Instruction/ maintenance manual of the product KM2030 en-CA Miele
Go to page of 18
Installation Instructions KM2030 en-CA IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE To prevent accidents and machine damage read these instructions before installation or use.
To avoid damage to the appliance, it should not be installed until the upper cabinet and exhaust hood have already been mounted. ~ This appliance is not connected to an exhaust vent. It must be installed and connected to the power supply in compliance with the applicable installation requirements.
Upper clearance For an exhaust hood above the appliance, the safe clearance distance indicated by the hood manufacturer must be maintained. If there are no specifications from the hood manufacturer or if flammable materials (e. g., a hanging cabinet) are installed above the appliance, the clearance distance must be at least 30" (760 mm).
When installing a gas stovetop, the cabinetry or walls to ONE side and to the rear of the appliance can be as tall as you wish. However, on the other side there must not be any appliance or furniture that is taller than the installed gas stovetop (see illustrations).
KM 2030 a front b Installation height c Gas connection R 1/2" ISO 7-1 d Junction box with power cable ,L=7 8 3 / 4 " (2000 mm) Appliance and installation dimensions 29.
KM 2050 a front b Installation height c Gas connection R 1/2" ISO 7-1 d Junction box with power cable ,L=7 8 3 / 4 " (2000 mm) Appliance and installation dimensions 30.
How to make the countertop cut-out ^ Use the template to make a countertop cut-out. Be sure to observe the minimum distance from the rear wall and from the left or right to a side wall .
Sealing NEVER use sealing unless it is explicitly called for in the instructions. The sealing strip under the edge of the upper part of the appliance provides a sufficient seal against the countertop.
This appliance must be grounded according to local or national codes. All electrical work should be performed by a qualified electrician in accordance with local codes and with the: - National Electrical Code ANSI / NFPA 70 for the USA or - Canadian Electrical Code Part I for Canada (CSA Standard C 22.
Installation and service must be performed by a qualified installer, service agency or the gas supplier. This appliance must be installed with its own shut off valve and the included gas pressure regulator.
Gas pressure regulator A pressure regulator that is convertible from natural to LP gas (Propane) or vice versa is included with the appliance. The included regulator corresponds with the gas type of the appliance. Verify before installing. The adjusted pressure is: natural gas - 4" w.
The appliance should have been ordered for connection to either natural gas or LP gas (propane). If the appliance is not configured for the proper type of gas connection please contact your Miele Dealer.
Rated load at high setting Burner Type of gas KM 2030 KM 2050 BTU/hr kW BTU/hr kW Small burner Natural gas (NG) Liquid gas (LP) 3500 3500 1,00 1,00 3500 3500 1,00 1,00 Regular burner Natural gas (NG) .
, Switchover to a different gas type should only be performed by a duly authorized gas company technician. Save the nozzles removed from the appliance for future use. Nozzle table If you switch to a different type of gas, the large and small burner nozzles will need to be changed.
How to change a nozzle Unplug the appliance from the electrical supply. How to change the main nozzle ^ Remove the burner cover b , the burner ring a (wok) and the burner head c . ^ Use a socket wrench (M7) to unscrew the main nozzle h . ^ Insert the proper nozzles (see Nozzle table) and tighten them down.
How to change the small nozzles (all burners) To change the small nozzles, you will first need to remove the upper part of the appliance. ^ Unscrew the mounting screws on the burner. ^ Pull the control knob up and off. ^ Take off the upper part of the appliance.
After switching over ^ Use the reverse order to re-assemble the burner parts. ^ Before putting the upper part of the appliance back in place, light each burner with matches to test the seal on all the gas flow parts. ^ After testing, set aside the loose burner parts.
Alteration rights reserved / 4908 For the most updated manual see the Miele web site. M.-Nr. 07 520 080 / 00.
An important point after buying a device Miele KM2030 en-CA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele KM2030 en-CA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele KM2030 en-CA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele KM2030 en-CA you will learn all the available features of the product, as well as information on its operation. The information that you get Miele KM2030 en-CA will certainly help you make a decision on the purchase.
If you already are a holder of Miele KM2030 en-CA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele KM2030 en-CA.
However, one of the most important roles played by the user manual is to help in solving problems with Miele KM2030 en-CA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele KM2030 en-CA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
