Instruction/ maintenance manual of the product 911184 LM21SW CLASSIC Ariens
Go to page of 30
Owner/Operator Man ual Manuel Du Prop riétaire/Utilisateu r Model 91 1 160 – LM21 Cl assic 91 1 182 – LM21 Cl assic 91 1 183 – LM21S Classic 91 1 184 – LM21SW Classic W alk Behind Lawn Mower .
GB - 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Assembly . . . . . . . . . . . . . . . . . . . . . . . . 9 Controls a nd Fe a t ure s . . . . . . . . . . . . 10 Operati on . . . . . . . . . . . . . . . . . . . . . . . 1 1 Mainten ance.
GB - 3 • Record Unit Model and Serial numbers here: • Record Engine Model & Serial numbers here: PRODUCT REGISTRA TION The Ariens d ealer must register the product at the time of purchase. Registering the product will help the company process warranty claims or contact you with the latest service information.
GB - 4 SAFETY ALERTS Look for these symbols t o point out important safety precautions. They mean: Attention! Personal Safety Is Involved ! Become Al ert! Obey T he Messag e! The safety alert symbols above an d signal words below are used on decals and in this manual.
GB - 5 SAFETY DECALS AND LOCA TIONS AL WA YS replace missing or damage d safety decals. Refer to Figure 2 for safety decal locations. 1. DANGER! TO A VOID SE RIOUS INJUR Y OR DEA TH 2. DANGER! KEEP HANDS AND FEET A W A Y Do not opera te mower unless guard s are in operating position or bagger is att ac hed.
GB - 6 Keep away from drop-offs, ditches, or embankments that could c ause operator to lose footing or cont rol of unit. AL WA YS be awa re of traffic when operating along streets or curbs. Keep work area clear of all persons, children and pets. Keep children out of the work area a nd under the watchful care of a responsible adult .
GB - 7 DO NOT mow at too fast a r ate. DO NOT change engine governor setting or over- speed the engine. Do not operate m ower on gravel or loose material such a s sand. S top mower when crossing drives, walks , or roads to prevent damage or injury f rom thrown objects.
GB - 8 Accidental engine start up can cause death or serious injury . Excep t where specifically recommended, AL WA YS stop engine, remove key (electric start models), wait for moving parts to stop, allow parts to cool and disconnect spark plug wire before inspecting, servicing, adjusting or repairing unit.
GB - 9 CARTON CONTE NTS ASSEMB L Y 1. Unfold and adjust handlebar . See HANDLEBAR HEIGHT on page 20 . NOTE: DO NOT bend the speed control rod (if equipped) when unf olding the handlebars. 2. F ill engine crankcase with oil. Se e engine manual. 3. Set -up mowe r for bagging, side discharge or m ulching.
GB - 10 1. Engine/Blade Control 2. Wheel Drive Control ( 91 1 183, 184) 3. Adjustable and Fol ding Handlebars 4. Swivel Wheel Lock (91 1 184) 5. Grass Bag 6. Rear Door 7. Fuel T ank and Cap 8. Height Adjustment P ins (91 1 184) 9. Muffler and Muffler Guard 10.
GB - 11 CONTROLS AND FEA TURES See Figure 4 for locations. Engine/Blade Control The engine/blade control must be held against the handlebar to start the engine and blade. Engine/blade control feature on mower stops engine and blade within 3 secon ds whenever operator releases handlebar .
GB - 12 S tand ard Models T o c hange cutting height, move cutting height levers one notch at a t ime on each wheel to set desired height (Figure 5). NOTE: Each wheel on mower must be set at the same height fo r a level cut.
GB - 13 S peed Control (self-prope lled models) S peed control rod changes the mower ’s forward travel speeds. S tart mowing slowly and use speed control rod to gradually increase speed to a safe, comfortable walking pace. S peed control rod should hold the desired speed.
GB - 14 FILLING THE FUEL T ANK GASOLINE IMPORT ANT : AL W A YS use gasoline that meets the following guidel ines: • Clean, fresh gasoline. • A minimum o f 87 octane/87 AKI (91 RON). High altitude use may require a diff erent octane. Consult your engine manual.
GB - 15 To B a g 1. Shut of f unit. 2. Install side discharge co ver . 3. Lift rear door . 4. Hook grass bag frame on m ounting flange. 5. Lower rear doo r . If necessary , lift rear of gr ass bag frame to lock in position. There should be no openings between bag and mounting surface after inst alling bag.
GB - 16 EMERG ENCY STOPP ING T o stop the m ower in an emergency: 1. Release the engine/blade control. 2. Release the wheel drive control (self- propelled models). 3. Allow all moving parts to stop before leaving operator ’s position. ST ARTING AND SHUT OFF See Figure 4 for all Controls and Features.
GB - 17 Ariens Dealers will provide any service, parts or adjustments which may be required to keep your unit operating at peak ef ficiency . Should engine require se rvice, contact an Ariens Dealer or an authorized engine manufacturer's service center .
GB - 18 CHECK WHEEL DRIVE CONTROL (Self-Propelled Models) The unit must stop quickly and c ompletely when the control is released. Adjust or rep air if necessary . Se e WHEEL DRIVE CONTROL ADJUST MENT on page 22. CHECK GRASS BAG Check grass bag frequently for wear or deterioration.
GB - 19 3. Check mower blade balance. Slide mower blade on an unthreaded bolt. A balanced blade should remain in a horizontal position. If eit her end of mower blade moves downward, sharpen the heavy end until blade is balanced (Figure 12). 4. Install mower blade on unit.
GB - 20 SER VICE PO SITION Put unit into se rvice position for eas y access to underneath the deck. 1. Place unit on a flat, level surface. 2. Disconnect spark plug w ire. 3. Remove fuel cap, place a piece of plastic bag over the opening and tighten cap securely .
GB - 21 ENGINE/BLADE CONTROL ADJUSTMENT (91 1 184) T o adjust engine/blade control: 1. Loosen cable nuts away from bracket. 2. Squeeze z-bend brac ket at engine end of cable toward front of unit and hold in place. 3. Pull cable down from br acket until there is no slack in cable.
GB - 22 WHEEL DRIVE CONTROL ADJUSTMENT (Self-Propelled Models) See Figure 16. NOTE: When the whee l drive control is disengaged, the gap between the friction disc and the aluminum drive plate should be approximately .030" (0.7mm). See Figure 16. Check the adjustment with the engine off and with the engine on: 1.
GB - 23 T o decrease the gap between the friction disc and the aluminum drive plate: 1. Loosen the upper cable nut on the wheel drive control cable, and then tighten t he lower cable nut against the adjuster bracket. See Figure 18. 2. Check the adjustment and readjust as needed.
GB - 24 IMPORT ANT : NEVER spray unit with high- pressure wa ter or store unit outdoors . S tore mower in a coo l, dry , protected location. Cleaning Clean unit thoroughly with mild soap and low pressure water . Brush off dirt and debris from all surfaces.
GB - 25 TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Engine will not st art 1. Fuel tank empty or low . 2. Sp ark plug wire loose or off . 3. E ngine/Blade control cable detached, broken, or not adjusted properly . 1. Chec k fuel level. Fill tank if necessary .
GB - 26 SER VICE P ARTS Always use genuine Ariens parts to keep your mow er running like new. Description Part Number Air Filter 21543500 (91 1 160) Air Filter 21541000 (91 1 182, 183, 184) S park Plu.
GB - 27 SPECIFICA TIONS Model Number 91 1 183 91 1 184 91 1 160 91 1182 Descript ion LM21S LM21SW LM21 LM21 Length - in. ( cm) 61.5 (156) Height - in. (cm) 38 (96.5) Width - in. (cm) 23 (58.4) Actual Weight - l bs (kg) 109 (49.4) 125 (56.7) 99 (44.9) 99 (44.
ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NA TIONAL ® | BYNOR M ® | EVERRIDE ® | GREA T DANE ® Con_L&G_2010 29 T wo-Y ea r Limited Lawn and Garden W a rranty This warranty statement.
ARIENS COMP ANY GRA VEL Y ® | STENS ® | LOCKE ® | NA TIONAL ® | BYNOR M ® | EVERRIDE ® | GREA T DANE ® Con_L&G_2010 30 T o find an Ari ens or Gra vely auth orized ser vice repr esentative, contact Arie ns at: 655 W. Ryan Street Brillion, WI 541 10 (920) 7 56 - 21 41 www .
Ariens Company 655 West Ryan St reet Brillion, W I 541 10-1 072 920-756-2141 Fax 920-756-2407 www .ariens.com.
An important point after buying a device Ariens 911184 LM21SW CLASSIC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ariens 911184 LM21SW CLASSIC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ariens 911184 LM21SW CLASSIC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ariens 911184 LM21SW CLASSIC you will learn all the available features of the product, as well as information on its operation. The information that you get Ariens 911184 LM21SW CLASSIC will certainly help you make a decision on the purchase.
If you already are a holder of Ariens 911184 LM21SW CLASSIC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ariens 911184 LM21SW CLASSIC.
However, one of the most important roles played by the user manual is to help in solving problems with Ariens 911184 LM21SW CLASSIC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ariens 911184 LM21SW CLASSIC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
