Instruction/ maintenance manual of the product DA 3480 Miele
Go to page of 40
Operating and Installation Instructions Ventilation System DA 3460 DA 3480 DA 3490 To prevent accidents and appliance damage, read these instructions before installation or use.
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Guide to the Ventilation System . . . .
READ AND SAVE THESE INSTRUCTIONS Keep these instructions in a safe place and pass them on to any future user. Read these instructions carefully before installing or using the Ventilation System. ~ This appliance is intended for residential use only. Use the appliance only for its intended purpose.
~ d) Before connecting the appliance to the power supply make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond to prevent appliance damage. If in doubt consult a qualified electrician.
, WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A COOKTOP GREASE FIRE, OBSERVE THE FOLLOWING * : ~ a) SMOTHER FLAMES with a close fitting lid, cookie sheet, or metal tray then turn off the burner. BE CAREFUL TO PREVENT BURNS . If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
Installation , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: ~ a) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
The ventilation hood offers two modes of operation: Air extraction The air is drawn in and cleaned by the grease filters and directed outside. The hood comes equipped with a non-return flap . The flap automatically closes when the hood is turned off so that no exchange of outside air and room air can occur.
Guide to the Ventilation System 8.
a Vent connection b Control panel c Grease filter d Expandable fume deflector e Overhead cooktop light f Active charcoal filter Optional accessory for recirculation mode g Facia Panel Accepts a custom.
The ventilation system is operated by pulling out and pushing in the expandable fume deflector. To turn the fan on ^ Pull the fume deflector out. The fan turns on to Level 2 .
Automatically switching back the intensive power level The intensive level can be programmed to automatically switch back to level 3 after 10 minutes. ^ To set this option, the fan and the overhead lighting must be turned off and the fume deflector pushed in.
, WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before cleaning or servicing the hood, disconnect it from the power supply, see "Important Safety Instructions". , The halogen bulbs are very hot when in use.
Grease filter The reusable metal grease filter removes solid particles from the vented kitchen air (grease, dust, etc). The grease filter should be cleaned ever y3-4 weeks. , A dirty filter is a fire hazard. ^ To remove hold and pull out the deflector and the grease filter together.
^ To insert the grease filter, make sure that the red plastic guides are at the front and facing up. ^ Insert the grease filter in the deflector and push upwards. It should glide onto the fixing pins. Inserting / replacing the active charcoal filters For recirculation mode an active charcoal filter must be used in addition to the grease filter.
Changing the light bulbs , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before changing the light bulbs, disconnect the hood from the power supply, see "Important Safety Instructions". When in use halogen bulbs become extremely hot, use caution.
Repairs In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department. ^ When contacting the Technical Service Department, please quote the model and serial number of your appliance. These are shown on the data plate which is visible when the grease filters are removed.
Installation Instructions Read these instructions and the "Important Safety Instructions" before installing this ventilation system. The installation steps are described in the enclosed "Installation Diagram". Leave these instructions with the appliance for the consumer/user.
18.
Disposal of packing material The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Please recycle. , DANGER Ensure that any plastic wrappings, bags, etc., are disposed of safely and kept out of the reach of babies and young children.
Appliance dimensions 20.
* The hood can also be installed in a 23 5 / 8 " (60 cm) cabinet. Appliance dimensions 21.
* The hood can also be installed in a 23 5 / 8 " (60 cm) cabinet. Appliance dimensions 22.
1) Air extraction mode; consider accessories when measuring cabinet height and cut-outs (e.g. muffler). 2) Recirculation mode with Installation kit DUU 151 Distance between cooktop and hood (S) Do not install this exhaust hood over cooktops burning solid fuel.
Installation accessories Installation 24.
a 2 runners (1 x right, 1x left) to support the hood in the cabinet. b 1 spacer strip to conceal the gap between the rear of the appliance and the wall.
Installation 26.
1. Installing the space bar T = K cabinet depth minus G hood depth ^ The hood depth G depends on the custom panel: – a Hood installed without front panel – b Hood installed with a cabinet matching custom panel These measures are only valid for the installation if the front panel sits flush with the cabinet corpus (without the door).
2. Runners The runners are made for side walls of 5/8" (16 mm) and 3/4" (19 mm). Screw on the angled side which has the imprint of the respective cabinet wall measure. ^ Align the runners with the drawn line and be sure that they are flush with the lower edge of the cabinet side wall.
^ Take the grease filter out and put it aside. ^ Push the deflector back in. ^ When installing a 29 13 / 16 " (80 cm) or a3 5 1 / 4 " (90 cm) hood into a 23 5 / 8 " (60 cm) cabinet, unscrew the deflector spring clips while the deflector is pulled out.
4. Secure the appliance ^ Push the hood back so it sits flush with the front of the spacer strip. ^ Pull the deflector out. ^ Screw the hood, with 4 screws, onto the runners. ^ Remove the installation protection between the deflector and casing. ^ Loosen the screws of the fixing brackets on the hood top.
The DA3460, DA3480 and DA3490 Built-In Ventilation Hoods all include brackets to affix the hood body to the rear wall of the enclosing cabinet. (Fig. 1) These brackets are necessary to ensure the long-term rigidity and stability of the installed appliance.
Weight of the front panel The weight of the front panel must not exceed 2.8 lbs (1.3 kg). This applies for front panels with a depth of up to 1 1 / 4 " (30 mm). In the case of front panels of greater depth or greater weight, the weight must be reduced by milling out the back of the panel, for instance.
7. Venting Air extraction mode ^ Complete the venting installation, see "Air extraction". Recirculation mode If the hood cannot be installed for air extraction the appliance must be connected for recirculation mode. For recirculation mode a respective installation kit is recommended which can be obtained from Miele.
, WARNING Danger of toxic fumes. Gas cooking appliances release carbon monoxide that can be harmful or fatal if inhaled. To reduce the risk of fire and to properly exhaust air, the exhaust gases extracted by the hood should be vented outside of the building only.
– If the exhaust is ducted into an inactive flue, the air must be expelled parallel to the flow direction of the flue. Never connect an exhaust hood to an active chimney, dryer vent, flue, or room venting ductwork. Seek professional advice before connecting an exhaust hood vent to an existing, inactive chimney or vent flue.
, WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: All electrical work should be performed by a qualified electrician in strict accordance with national regulations (for USA: ANSI-NFPA 70) and local safety regulations.
Maximum load ...............4 5 0W Light .....................2x5 0W Voltage .....................1 2 0V Frequency ..................6 0H z Circuit rating ..................1 5A Weight DA 3460 ........... 27.6 lb (12.5 kg) DA 3480 ........... 29.8 lb (13.
38.
39.
M.-Nr. 09 190 990 / 03 Alteration rights reserved / 3912 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
An important point after buying a device Miele DA 3480 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Miele DA 3480 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Miele DA 3480 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Miele DA 3480 you will learn all the available features of the product, as well as information on its operation. The information that you get Miele DA 3480 will certainly help you make a decision on the purchase.
If you already are a holder of Miele DA 3480, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Miele DA 3480.
However, one of the most important roles played by the user manual is to help in solving problems with Miele DA 3480. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Miele DA 3480 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
