Instruction/ maintenance manual of the product R104-11 METRObility Optical Systems
Go to page of 16
Installation & User Guide Model: R104-1 1 M ETROBILITY ® F OUR - POR T S WITCH PWR 10/100 BASE LK AT LK AT LK AT LK AT 1 2 3 4.
This publication is protected by the copyright laws of the United States and other countries, with all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, tra.
T able of Contents Metrobility 4-port Switch Installation & User Guide Overview .............................................................................................................. 4 Installation Guide ...................................
4 Overview Overview The Metrobility ® R104-1 1 is a four -port 10/100Mbps TX switch that provides a cost-effective solution for situations in which a simple switching option with few ports is required. When configured for stacking in a Metrobility chassis, the card eliminates the need for any external equipment.
Metrobility 4- port Switch 5 Installation Guide Follow the simple steps outlined in this section to install and start using the R104. NOTE: Electr ostatic dischar ge pr ecautions should be taken when handling any cir cuit boar d. Pr oper gr ounding is r ecommended (i.
6 Installation Guide *DIP switches also can be managed via console commands or with the Metrobility NetBeacon® or WebBeacon™ management software. Refer to the Command Line Interface Reference Guide.
Metrobility 4- port Switch 7 Duplex Switch (FD) Switch FD determines the duplex mode on all ports that have auto- negotiation disabled. • The ports will operate at full duplex if FD is OPEN. (default) • They will operate at half duplex if FD is CLOSED.
8 Installation Guide AN indicates that auto-negotiation is enabled. + indicates the switch is enabled (OPEN) . — indicates the switch is disabled (CLOSED). A blank space indicates that the switch setting is not applicable and can be either OPEN or CLOSED.
Metrobility 4- port Switch 9 • Insert the card into either slot in the R400 or R1000. In the R5000 chassis,any slot excluding slot #17. Make sure the top and bottom edges of the board are aligned with the top and bottom card guides in the chassis. Do not force the card into the chassis unnecessarily .
10 Installation Guide Connect to the Network T o connect the R104 to the network, insert the twisted-pair cables into the appropriate connectors. Be sure the card is secured to the chassis by tightening the thumbscrew before making network connections.
Metrobility 4-port Switch 11 User Guide This section contains information regarding the operating featur es of the Metrobility R104. LED Indicators The R104 provides several LEDs for the visible verification of unit status and proper functionality . These LEDs can assist in troubleshooting and with overall network diagnosis and management.
12 User Guide T echnical Specifications Network Connections T wisted-Pair Interface Connector __________________________________ Shielded RJ-45, 8-pin jack Impedance ________________________________________ 100 Ohms nominal Signal Level Output (differential) ________________ 0.
Metrobility 4-port Switch 13 Product Safety , EMC and Compliance Statements This equipment complies with the following requirements: •U L • CSA •C E •C B • FCC Part 15, Class A • EN55022 C.
14 User Guide W arranty and Servicing T elco Systems’ Pr oduct W arranty TELCO MAKES NO W ARRANTIES EXCEPT AS HEREIN SET FOR TH: T elco warrants that the equipment and accessories manufactured by T .
Metrobility 4-port Switch 15 Replacement, Repair or Refund Procedur e for Hardware: T elco’ s sole obligation under this express warranty shall be, at T elco’ s option and expense, to repair the defective product or part or deliver to Customer an equivalent product or part to replace the defective item.
5660-000023 D 12/06 US Headquarters 2 Hampshire Street Suite 3A Foxboro MA USA 02035 tel: 1.781.551.0300 • fax: 1.781.255.2344 www .telco.com.
An important point after buying a device METRObility Optical Systems R104-11 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought METRObility Optical Systems R104-11 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data METRObility Optical Systems R104-11 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, METRObility Optical Systems R104-11 you will learn all the available features of the product, as well as information on its operation. The information that you get METRObility Optical Systems R104-11 will certainly help you make a decision on the purchase.
If you already are a holder of METRObility Optical Systems R104-11, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime METRObility Optical Systems R104-11.
However, one of the most important roles played by the user manual is to help in solving problems with METRObility Optical Systems R104-11. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device METRObility Optical Systems R104-11 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
