Instruction/ maintenance manual of the product MCD-479 Metrik Mobile Electronics
Go to page of 12
PLL SYNTHESIZER STEREO RADIO WITH COMP A CT DISC PLA YER DIGIT AL + – OWNER'S MANU AL MCD-479.
2 INST ALLA TION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver . • Before completly installing the unit, connect the wiring temporarily and make sure it is functioning properly.
3 1. Dashboard 2. Nut (5mm) 3. Spring washer 4. Screw (5 x 25mm) 5. Screw 6. Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. 7. Plain washer Removing the unit 1. Frame 2. Insert fingers into the groove in the front of frame and pull out to remove the frame.
HOW TO REMOVE AND INST ALL THE FRONT P ANEL 1. Press the release button and pull-off the front panel. Place the front panel into the supplied case to protect it. 2. T o install the front panel, insert the right side of thepanel into the housing first, then press the left side in until it locks in place.
5 WIRING CONNECTIONS 1. All connections should be soldered and insulated with electrical tape. 2. Be sure to connect the red power input lead to + 12V power terminal after all the other leads have been properly connected. 3. Run all ground wires to a common ground.
6 + – 25 6 9 8 12 10 13 4 7 5 18 19 20 17 24 15 1 14 2 16 11 3 21 22 23 Basic Operation 1.0 ON/OFF Press PWR button (1) to turn on. Press PWR again to turn it off. 2.0 Select Mode Press SEL button (2) to move display through volume, bass, treble, balance and fader functions.
7 8.0 Mute Press MUTE (13) to silence the receiver . Press again to resume listening. 9.0 Set the Clock 10.1 Press and hold DSP button (1 1) for three seconds until the display flashes.
8 Radio Operation 1.0 Select a Band Press BND button (5) to change between three FM bands and AM/L W bands. Each band stores up to six preset stations. 2.0 Select a Station T ouch a TUNE button (7) or (6) for less than two seconds to move radio frequency number down or up on step.
9 CD Player Operation 1.0 Insert and Eject CD Insert a CD into the loader slot. The CD will begin to pla y . Press (eject) (10) to stop CD play and eject the CD. The Receiver automatically switches to radio operation. 2.0 Skip T racks Press TUNE (7) or (6) to advance CD to next track.
10 SPECIFICA TION GENERAL Power Supply Requirements : DC 12 V olts, Negative Ground ONLY Chassis Dimensions : 178 (W) X 155 (D) X 50 (H) Tone Controls - Bass (at 100 Hz) : +10 dB/ – 10 dB - T reble .
11 TROUBLE SHOO TING Be f ore going through the che c k list, check all wiring connections. If any of the problems persist after check list has been completed, consult your Metrik deale r . Symptom Cause Solution No power . The car ignition is not If the power supply is properly on.
88-06902-37 L I M I T E D O N E Y E AR W ARRAN T Y This warranty shall be in e ffect for a period of one year fro m the date of the first consumer purchase. This w arranty is valid during the warranty period providing that proo f of date of purchase fro m an authorized deale r is presented whenever warranty service is required.
An important point after buying a device Metrik Mobile Electronics MCD-479 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metrik Mobile Electronics MCD-479 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metrik Mobile Electronics MCD-479 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metrik Mobile Electronics MCD-479 you will learn all the available features of the product, as well as information on its operation. The information that you get Metrik Mobile Electronics MCD-479 will certainly help you make a decision on the purchase.
If you already are a holder of Metrik Mobile Electronics MCD-479, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metrik Mobile Electronics MCD-479.
However, one of the most important roles played by the user manual is to help in solving problems with Metrik Mobile Electronics MCD-479. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metrik Mobile Electronics MCD-479 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
