Instruction/ maintenance manual of the product 99-8711 Metra Electronics
Go to page of 8
INST ALLA TION INSTRUCTIONS FOR P ART 99-8711 99-8711 KIT FEA TURES • DIN Radio Provision with Pocket • Stacked DIN Units Provision A) Radio Housing B) Pocket KIT COMPONENTS A Small Flat Blade Screwdriver/ Panel Removal T ool • Phillips Screwdriver • T orx Screwdriver 1-800-221-0932 © COPYRIGHT 2004 METRA ELECTRONICS CORPORA TION www .
Dash Disassembly - M e r c e d e s C - C l a s s 2 0 0 1 - 2 0 0 4 ...................................... 1 - M e r c e d e s C L K 2 0 0 4 .............................................. 2 Kit Assembly - D I N M o u n t R a d i o P r o v i s i o n ...
99-8711 DA SH DISASSEMBL Y MERCEDES C-CLASS 2001-2004 A B 1 D isconnect the negative battery ter- minal to prevent an accidental short circuit. 1 Unclip shifter trim (with gear indica- tors). 2 Unclip and remove center console trim panel. (Figure A) 3 Repeat steps 5 and 6 for the other vent and remove vent assembly .
2 99-8711 DA SH DISASSEMBL Y B A C D MERCEDES CLK 2004 Loosen shifter boot and pull up over shifter handle . (Figure A) 2 T urn the retainer on the shifter 1/2 turn to remove shifter handle and boot. (Figure B) 3 Unclip and remove the shifter trim panel.
3 99-8711 KIT ASSEMBL Y B A DIN MOUNT RADIO PROVISION Slide the aftermarket radio into the cage until it snaps into place . (Figure B) 2 Slide the pocket into the radio housing until it snaps into place . (Figure B) 3 Continue to final assembly . * Note: Refer also to the instructions included with the aftermarket radio.
4 99-8711 KIT ASSEMBL Y B A ST A CKED DIN UNITS PROVISION Slide the aftermarket units into the cages until they snap into place . (Figure B) 2 Continue to final assembly . * Note: Refer also to the instructions included with the aftermarket radio. Slide the DIN cages into the Radio Housing and secure by bending the metal locking tabs outward.
99-8711 FINAL ASSEMBL Y FINAL A SSEMBL Y (A) Strip wire ends back 1/2" B) T wist ends together C) Solder D) T ape A B C D Locate the factory wiring har ness in the dash. Metra recommends using the proper mating adapter and making connections as shown.
99-8711 INSTRUCTIONS 1-800-221-0932 REV . 10/20/06 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-8711 www .metraonline.com.
An important point after buying a device Metra Electronics 99-8711 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metra Electronics 99-8711 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metra Electronics 99-8711 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metra Electronics 99-8711 you will learn all the available features of the product, as well as information on its operation. The information that you get Metra Electronics 99-8711 will certainly help you make a decision on the purchase.
If you already are a holder of Metra Electronics 99-8711, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metra Electronics 99-8711.
However, one of the most important roles played by the user manual is to help in solving problems with Metra Electronics 99-8711. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metra Electronics 99-8711 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
