Instruction/ maintenance manual of the product 99-8205 Metra Electronics
Go to page of 12
INST ALLA TION INSTRUCTIONS FOR P ART 99-8205 1-800-221-0932 www .metr aonline.com © COPYRIGHT 2004-08 METRA ELECTRONICS CORPORA TION KIT FEA TURES • DIN head unit provision • ISO DIN head unit p.
T ABLE OF CONTENTS 99-8205 Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 4, 5, 6, 7,8 Final Assembly . . . . . . . . . . . . . . .
99-8205 1 Disconnect the negative batter y terminal to prevent an accidental short circuit. 1 Unclip the bottom edge of the radio trim panel then lift up and out to remove . (Figure A) 2 TO Y OT A MA TRIX 2003-2008 PONTIA C VIBE 2003-2008 Remove (4) 10 MM bolts securing the factor y r adio.
99-8205 KIT ASSEMBL Y 2 Attach the pocket to the bac k of the ISO/DIN Faceplate (by holding the faceplate upside down and inserting the right edge of the pocket into place then pushing the rest of the pocket onto the lip) and mount with (2) #8X3/8” Phillips screws.
99-8205 KIT ASSEMBL Y 3 Slide the DIN cage into the Radio Housing and secure b y bending the metal locking tabs down. ( Figure E) 5 Slide the aftermarket head unit into the cage and secure .
4 ISO DIN HEAD UNIT PRO VISION 99-8205 KIT ASSEMBL Y Attach the the pocket to the back of the ISO/DIN Faceplate (by holding the face- plate upside down and inserting the right edge of the pocket into place then push- ing the rest of the pock et onto the lip) and mount with (2) #8X3/8” Phillips screws.
5 ISO DIN HEAD UNIT PRO VISION 99-8205 KIT ASSEMBL Y Mount the ISO Brackets to the head unit with the screws supplied with the unit. ( Figure E) 5 Mount the rear support to the back of the pocket with (2) #8x3/8” Phillips screws. ( Figure D) 4 Slide the the head unit into the radio opening until the side clips engage .
6 DOUBLE DIN HEAD UNIT PRO VISION 99-8205 KIT ASSEMBL Y Cut and remove the bottom portion (Displayed) of the mounting brack- ets. ( Figure A) 1 NO TE: 2005-2008 Matrix not applicable .
ST A CKED ISO DIN HEAD UNIT PROVISION Cut and remove the bottom portion (Displayed) of the mounting brack- ets. ( Figure A) 1 A Attach the ISO spacers to the mount- ing brackets b y inserting the (4) bosses on each spacer into the (4) holes in each brack et.
8 FINAL A SSEMBL Y 1 Locate the factor y wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.
9 NOTES 99-8205.
INST998205 1-800-221-0932 www .metr aonline.com © COPYRIGHT 2004-08 METRA ELECTRONICS CORPORA TION INST99-8205 REV . 09/26/08.
An important point after buying a device Metra Electronics 99-8205 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metra Electronics 99-8205 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metra Electronics 99-8205 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metra Electronics 99-8205 you will learn all the available features of the product, as well as information on its operation. The information that you get Metra Electronics 99-8205 will certainly help you make a decision on the purchase.
If you already are a holder of Metra Electronics 99-8205, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metra Electronics 99-8205.
However, one of the most important roles played by the user manual is to help in solving problems with Metra Electronics 99-8205. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metra Electronics 99-8205 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
