Instruction/ maintenance manual of the product 99-7875 Metra Electronics
Go to page of 12
INST ALLA TION INSTRUCTIONS FOR PART 99-7875/99-7875T 99-7875/99-7875T APPLICA TIONS Honda Accord 2008-2010 (For Non-Navigation models with Dual Zone Climate controls) Honda Accord Cr osstour 2010 KIT.
.
99-7875/99-7875T DASH DISASSEMBL Y HONDA ACCORD 2008-10 / CROSSTOUR 2010 1 1 Unclip and remove the trim panel at the left side of the factory radio. ( Figure B) Disconnect the negative battery ter- minal to prevent an accidental short circuit. 3 Unclip and remove the trim panel from above the glove box at the right side of the factory radio.
99-7875/99-7875T DASH DISASSEMBL Y 2 Remove (2) Phillips screws facing up on the bottom of the factory radio. ( Figure H) 9 Unclip and remove the hazard switch/passenger air bag light assembly . (Retain the hazard switch/passenger air bag light assembly for re-use during kit prepa- ration.
99-7875/99-7875T KIT PREPARA TION PAS SENGER AIRBAG 3 1 Secure the climate controls into the radio housing using the factory hard- ware from rear . ( Figure C) Snap the hazard switch/passenger air bag light assembly into the radio housing from front. ( Figure A) 3 Secure the a/c vents into the radio housing using the factory hardware from rear .
99-7875/99-7875T KIT ASSEMBL Y 4 A B C DIN MOUNT RADIO PROVISION WITH POCKET Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 1 Slide the aftermarket radio into the DIN cage until it snaps into place .
99-7875/7875T KIT ASSEMBL Y 5 A B C ISO MOUNT RADIO PROVISION WITH POCKET Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 1 Slide the radio into the Radio Housing until it snaps into place . (Figure B) 2 Snap the T rim Plate onto the front of the Radio Housing.
99-7875/99-7875T KIT ASSEMBL Y 6 DOUBLE DIN/ST ACKED ISO MOUNT UNITS PROVISION Cut and remove the center bar from the Radio Housing. (Figure A) 1 Snap the Double DIN brackets to the inside edge of the Radio Housing.
99-7875/99-7875T FINAL ASSEMBL Y FINAL ASSEMBL Y (A) Strip wire ends back 1/2" B) T wist ends together C) Solder D) T ape A B C D Locate the factory wiring har ness in the dash. Metra recommends using the proper mating adapter and making connections as shown.
NOTES 8 99-7875/7875T.
NOTES 9 99-7875/99-7875T.
99-7875/7875T INSTRUCTIONS 1-800-221-0932 REV . 04/21/10 © COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORA TION INST99-7875 www .metr aonline.com.
An important point after buying a device Metra Electronics 99-7875 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metra Electronics 99-7875 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metra Electronics 99-7875 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metra Electronics 99-7875 you will learn all the available features of the product, as well as information on its operation. The information that you get Metra Electronics 99-7875 will certainly help you make a decision on the purchase.
If you already are a holder of Metra Electronics 99-7875, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metra Electronics 99-7875.
However, one of the most important roles played by the user manual is to help in solving problems with Metra Electronics 99-7875. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metra Electronics 99-7875 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
