Instruction/ maintenance manual of the product 99-7861 Metra Electronics
Go to page of 8
INST ALLA TION INSTRUCTIONS FOR P ART 99-7861 1-800-221-0932 www .metr aonline.com KIT FEA TURES © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORA TION REV .
Dash Disassembly Honda Pilot 2003-2008. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Honda Pilot 2006-2008 (Without Factor y Navigation) . . . . . . . . . . 2 Kit Assembly ... ................................... .3 DIN Head Unit Provision With Pocket .
99-7861 1 Disconnect the negative batter y terminal to prevent an accidental short circuit. 1 Using a small flat blade screwdriver remove the blank plate from upper right side of radio trim panel. (Figure A) 2 HOND A PILOT 2003-2008 Unsnap radio trim panel.
99-7861 2 Disconnect the negative batter y terminal to prevent an accidental short circuit. 1 Remove (2) screws from the top of the instrument panel trim. Unclip and remove the instru- ment panel trim. (Figure A) 2 HOND A PILOT 2006-2008 (Without Factory Navigation) Unclip and remove the left center trim panel.
3 99-7861 Select the proper radio housing for your vehicle . EX models use radio housing (E) and LX models use radio housing (L). The radio housings are labeled on one of the mounting tabs. (Figure A) 1 Mount the pocket to the back of the radio housing with the (2) #8x3/8” phillips pan head screws supplied.
4 99-7861 KIT ASSEMBL Y Slide DIN cage (supplied with radio) into the assembled radio housing from the front. (Figure A) 1 Secure DIN cage to radio housing b y bending the locking tabs outw ard. (Figure A) 2 Slide the radio into the DIN cage until it snaps into place .
5 99-7861 KIT ASSEMBL Y Align the holes in the ISO brackets with the holes in the radio . Mount the brackets to the r adio using screws supplied with the radio . (Figure A) 1 Slide the radio/brack et assembly into the assembled radio housing until it snaps into place .
6 99-7861 FINAL ASSEMBL Y FINAL A SSEMBL Y 1 Locate the factor y wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to pr event electrical short circuit.
An important point after buying a device Metra Electronics 99-7861 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metra Electronics 99-7861 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metra Electronics 99-7861 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metra Electronics 99-7861 you will learn all the available features of the product, as well as information on its operation. The information that you get Metra Electronics 99-7861 will certainly help you make a decision on the purchase.
If you already are a holder of Metra Electronics 99-7861, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metra Electronics 99-7861.
However, one of the most important roles played by the user manual is to help in solving problems with Metra Electronics 99-7861. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metra Electronics 99-7861 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
