Instruction/ maintenance manual of the product 99-7504 Metra Electronics
Go to page of 8
INST ALLA TION INSTRUCTIONS FOR PART 99-7504 99-7504 APPLICA TIONS Mazda 3 2004-2009 KIT FEA TURES • DIN Mount Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Bonus Display.
Dash Disassembly - M a z d a 3 2 0 0 4 - 2 0 0 9 ......................... . . . . . . . . 1 Kit Assembly - Display Brackets/Pocket Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - DIN Mount Radio Provision with Pocket . . . . . . . .
99-7504 DASH DISASSEMBL Y MAZDA 3 2004-2009 A CL O CK S ET LO A D FM1 /2 A M C D TA P E/ M D HOOK B REAR VI EW - DISPLA Y TRIM PA N EL C 1 D isconnect the negative battery ter- minal to prevent an accidental short circuit. 1 Unclip and remove display trim panel above radio .
99-7504 DISPLA Y/POCKET ASSEMBL Y DISPLA Y BRACKETS/POCKET ASSEMBL Y MAZDA 3 2004-2009 A B 2 Using the (2) 3/8” #10 bolts and (2) #10 nuts attach the display retention brackets to the display unit. 1 Using the (2) Phillips screws removed in step 4 of Dash Disassembly secure the display replacement pocket to the back of the display trim panel.
3 99-7504 KIT ASSEMBL Y A B C DIN MOUNT RADIO PROVISION Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 1 Slide the aftermarket radio unit into the cage and secure . (Figure B) 2 Snap the T rim plate into the Radio Housing.
99-7504 KIT ASSEMBL Y 4 A B ISO DIN MOUNT RADIO PROVISION Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure A) 1 Slide the radio into the radio housing until it snaps into place . (Figure B) 2 Attach the trim plate supplied with the kit to the front of the radio hous- ing assembly .
Note: When inserting the 99-7504 into the sub dash be aware of the locations pointed out in Figure B . If the 99-7504 does not snap in correctly the result will be a noticeable gap on each side of the installation kit.
FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder , T a pe. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
An important point after buying a device Metra Electronics 99-7504 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metra Electronics 99-7504 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metra Electronics 99-7504 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metra Electronics 99-7504 you will learn all the available features of the product, as well as information on its operation. The information that you get Metra Electronics 99-7504 will certainly help you make a decision on the purchase.
If you already are a holder of Metra Electronics 99-7504, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metra Electronics 99-7504.
However, one of the most important roles played by the user manual is to help in solving problems with Metra Electronics 99-7504. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metra Electronics 99-7504 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
