Instruction/ maintenance manual of the product 99-7013 Metra Electronics
Go to page of 12
INST ALLA TION INSTRUCTIONS FOR PART 99-7013 99-7013 APPLICA TIONS Mitsubishi Outlander 2007-2010 KIT FEA TURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double.
Dash Disassembly - Mitsubishi Outlander 2007-2010. . . . . . . . . . . . . . . . . . . . 1 , 2 Kit Preparation ...........................................3 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . .
99-7013 DASH DISASSEMBL Y MITSUBISHI OUTLANDER 2007-2010 PAS SE N G ER AIR BAG O FF P A S S E N G E R PA S SEN GER AIR BAG O F F P AS SEN G ER B C 1 D isconnect the negative battery ter- minal to prevent an accidental short circuit. 1 Unclip and remove the vents from the left and right side of the factory radio panel.
99-7013 DASH DISASSEMBL Y MITSUBISHI OUTLANDER 2007-2010 2 Remo ve the labels from the front of the radio trim panel at each side of the hazar d switch by pushing them out from behind the panel. (Retain the labels to be reused during kit prepa- ration) ( Figure F) 6 E F Continued to kit preparation.
99-7013 KIT PREPARA TION 3 Secure the hazard switch panel into the radio housing using the factory hardwar e removed previously and apply labels from the front of the factory radio trim panel to front of the Metr a radio panel. (Figure A,B) 5 Continue to kit assembly .
4 99-7013 KIT ASSEMBL Y A B C DIN RADIO PROVISION WITH POCKET Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 1 Slide the aftermarket radio into the cage until it snaps into place . (Figure B) 2 Snap the pocket into the radio housing .
99-7013 KIT ASSEMBL Y 5 B C D ISO MOUNT RADIO PROVISION WITH POCKET Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure A) 1 Slide the radio into the Radio Housing until it snaps into place . (Figure B) 2 Snap the T rim Plate onto the front of the Radio Housing.
99-7013 KIT ASSEMBL Y 6 B C DOUBLE DIN/ST ACKED ISO UNITS PROVISION Cut and remove the center bar from the Radio Housing. (Figure A) 1 Snap the Double DIN Brackets to the inside edge of the Radio Housing.
7 99-7013 FINAL ASSEMBL Y FINAL ASSEMBL Y (A) Strip wire ends back 1/2" B) T wist ends together C) Solder D) T ape A B C D Locate the factory wiring har ness in the dash. Metra r ecommends using the proper mating adapter and making connections as shown.
99-7013 NOTES 8.
99-7013 NOTES 9.
99-7013 INSTRUCTIONS 1-800-221-0932 REV . 04/21/10 © COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORA TION INST99-7013 www .metr aonline.com.
An important point after buying a device Metra Electronics 99-7013 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metra Electronics 99-7013 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metra Electronics 99-7013 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metra Electronics 99-7013 you will learn all the available features of the product, as well as information on its operation. The information that you get Metra Electronics 99-7013 will certainly help you make a decision on the purchase.
If you already are a holder of Metra Electronics 99-7013, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metra Electronics 99-7013.
However, one of the most important roles played by the user manual is to help in solving problems with Metra Electronics 99-7013. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metra Electronics 99-7013 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
