Instruction/ maintenance manual of the product 99-7011 Metra Electronics
Go to page of 12
INST ALLA TION INSTRUCTIONS FOR PART 99-7011 99-7011 MITSUBISHI Lancer 2008-2010 KIT FEA TURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provis.
Dash Disassembly - Mitsubishi Lancer 2008-2010 . . . . . . . . . . . . . . . . . . . . . . . . 1, 2 Kit Preparation ............................................ 3 Kit Assembly - DIN Radio Provision with Pocket ............................ .4 - ISO Mount Radio Provision with Pocket.
1 3 MITSUBISHI LANCER 2008-2010 99-7011 DASH DISASSEMBL Y D isconnect the negative battery ter- minal to prevent an accidental short circuit. 1 Open the glove box and remove (1) Phillips screw from the panel to the right of the glove box door . Unclip and remove the panel.
2 MITSUBISHI LANCER 2008-2010 99-7011 DASH DISASSEMBL Y 4 Unclip the radio switch panel includ- ing the hazard switch assembly . Unplug hazard switch assembly and remove panel. (Figure C) 5 Remove (4) Phillips screws secur- ing the radio chassis. Unplug and remove chassis.
3 99-7011 KIT PREPARA TION Secure the hazard switch assembly into the radio housing using the factory hard- ware . Snap the a/c vents into the radio housing . (Figure A) Use the (7) plastic factory clips previously removed during dash disassembly and attach where shown.
99-7011 KIT ASSEMBL Y 4 A B C DIN RADIO PROVISION WITH POCKET Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 1 Slide the aftermarket radio into the cage until it snaps into place . (Figure B) 2 Snap the pocket into the radio hous- ing.
99-7011 KIT ASSEMBL Y 5 A B C ISO MOUNT RADIO PROVISION WITH POCKET Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 1 Slide the radio into the radio housing until it snaps into place . (Figure B) 2 Snap the trim plate onto the front of the radio housing.
99-7011 KIT ASSEMBL Y 6 DOUBLE DIN RADIO PROVISION ST ACKED ISO MOUNT UNITS PROVISION Cut and remove the center bar from the radio housing. (Figure A) 1 Snap the Double DIN brackets to the inside edge of the radio housing .
99-7011 FINAL ASSEMBL Y FINAL ASSEMBL Y (A) Strip wire ends back 1/2" B) T wist ends together C) Solder D) T ape A B C D Locate the factory wiring har ness in the dash. Metra recommends using the proper mating adapter and making connections as shown.
99-7011 NOTES 8.
99-7011 NOTES 9.
99-7011 INSTRUCTIONS 1-800-221-0932 REV . 04/21/10 © COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORA TION INST99-7011 www .metr aonline.com.
An important point after buying a device Metra Electronics 99-7011 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metra Electronics 99-7011 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metra Electronics 99-7011 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metra Electronics 99-7011 you will learn all the available features of the product, as well as information on its operation. The information that you get Metra Electronics 99-7011 will certainly help you make a decision on the purchase.
If you already are a holder of Metra Electronics 99-7011, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metra Electronics 99-7011.
However, one of the most important roles played by the user manual is to help in solving problems with Metra Electronics 99-7011. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metra Electronics 99-7011 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
