Instruction/ maintenance manual of the product 95-7504 Metra Electronics
Go to page of 8
INST ALLA TION INSTRUCTIONS FOR PART 95-7504 95-7504 Mazda 3 2004-2009 KIT FEA TURES • Double DIN Radio Provision • Stacked ISO Mount Units Provision • Bonus Display Replacement Pocket • A) Ra.
Dash Disassembly - M a z d a 3 2 0 0 4 - 2 0 0 9 ......................... . . . . . . . . 1 Kit Assembly - Display Brackets/Pocket Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Double DIN Radio Provision . . . . . . . . . . . . .
95-7504 DASH DISASSEMBL Y MAZDA 3 2004-2009 A CL O CK S ET LO A D FM1 /2 A M C D TA P E/ M D HOOK B REAR VI EW - DISPLA Y TRIM PA N EL C 1 D isconnect the negative battery ter- minal to prevent an accidental short circuit. 1 Unclip and remove display trim panel above radio .
95-7504 DISPLA Y POCKET ASSEMBL Y DISPLA Y BRACKETS/POCKET ASSEMBL Y MAZDA 3 2004-2009 A B REAR VIEW - DISPLA Y R EPL ACE MENT P ANEL DISPLA Y REP LAC EMENT POCKET MOUNTED IN DISPLA Y TRIM PA N EL 2 Using the (2) 3/8” #10 bolts and (2) #10 nuts attach the display retention brackets to the display unit.
3 95-7504 KIT ASSEMBL Y A B C DOUBLE DIN RADIO PROVISION Slide the Double DIN radio into the br acket/radio housing assembly and secur e the radio to the assembly using the screws supplied with the radio . Snap the trim plate onto the front of the radio housing.
95-7504 KIT ASSEMBL Y 4 A B ST ACKED ISO UNITS PROVISION Snap the Double DIN brackets to the inside edge of the radio housing. (Figure A) 1 Slide the stacked ISO units into the bracket/radio housing assembly and secur e the units to the kit using the scr ews supplied with the units.
Note: When inserting the 99-7504 into the sub dash be aware of the locations pointed out in Figure B . If the 99-7504 does not snap in correctly the result will be a noticeable gap on each side of the installation kit.
FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder , T ape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
An important point after buying a device Metra Electronics 95-7504 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metra Electronics 95-7504 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metra Electronics 95-7504 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metra Electronics 95-7504 you will learn all the available features of the product, as well as information on its operation. The information that you get Metra Electronics 95-7504 will certainly help you make a decision on the purchase.
If you already are a holder of Metra Electronics 95-7504, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metra Electronics 95-7504.
However, one of the most important roles played by the user manual is to help in solving problems with Metra Electronics 95-7504. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metra Electronics 95-7504 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
