Instruction/ maintenance manual of the product 170-230 Metabo
Go to page of 17
115 117 3671 / D/GB/F/NL /1303 - 5.1 Betriebsanleitung Schutzgas-Schweißgeräte MIG/MAG 170 - 230 Operating Instruction MIG W elding Machines 170 - 230 Amp Models Notice d´utilisation postes de soud.
GB User Responsibility This machine will perform in conformity with the description contained in the instructions provided. This machine must be checked periodically. Defective equipment (including service leads) should not be used. Parts that are broken, missing, plainly worn, distorted or contaminated, should be replaced immediately.
MIG/MAG MIG/MAG MIG/MAG 180/35 ET 200/35 ET 230/40 ET Combi Welding range 25 - 180 A 25 - 200 A 25 - 230 A Open-circuit voltage 15.3 - 23 V 15.3 - 24 V 15.
2.1 Welding Output Box 6 Welding process Symbol e.g.: Manual metal arc welding with covered electrodes Tungsten inert-gas welding Metal inert and active gas welding including the use of flux cored wir.
b) Welding Output Box 6 Welding process Symbol e.g.: Manual metal arc welding with covered electrodes Tungsten inert-gas welding Metal inert and active gas welding including the use of flux cored wire.
Column a) need not be used if the duty cycle (duty factor) for the rated maximum welding current is 60 % or 100 %. Column b) need not be used if the duty cycle (duty factor) at the rated maximum welding current is 100 %. c) Energy input Box 14 Energy input symbol e.
4 Installing the Wire Spool 4.1 Disconnect from power mains Place wire spool onto spool carrier so that wire runs off clockwise. Central coupling KZ 2 for welding gun Wire feed regulator Weld time pot.
4.2 Wire Feed Set-up 5 Welding Stainless Steel and Aluminium This MIG welding machine is factory set for welding low-carbon steel. Use a mixed gas (e.g. Ar 99.988 %). 4.3 Feeding the Wire into the Torch Place the wire through the spiral guide tube across the feed roller into the central coupling's wire intake.
1. Disconnect torch lead assembly from machine and remove electrode wire. 2. Place aluminium wire spool onto spool carrier. 3. Remove liner collet from the torch lead's central coupling and pull steel liner from torch lead assembly.
6 Practical Hints for MIG Welding This distance required between the torch and the workpiece is directly related to the welding current: ● small current = small distance ● high current = greater distance Too little distance causes excessive wear of the contact tip and gas shroud.
8 Trouble Shooting Irregular wire feed Incorrect tension of tension roller Pilot groove of feed roller and intake nozzle not aligned Liner clogged or not correct size for wire Wire spooled irregularly.
9 Spare Parts List and Accessories 170/30 170/30 180/35 200/35 230/40 TL TL ET ET ET Description Stock-no. Combi Combi Rectifier bank 805 307 5313 x x Rectifier bank 805 307 0850 x Rectifier bank 805 .
Pos. Description Order No. Welding torch SB 14/2 cpl. with torch leads 3 m 090 200 9914 10 Swan neck cpl. 090 202 7378 12 Nozzle spring (5x) 090 202 7670 13 Head insulator 132 704 5241 15 Swan neck boot 132 706 1093 20 Handle red cpl. 132 704 5101 21 Trigger red 2-pol.
MIG W elding T orch SB 15/3; SB 15/4; SB 15/5 For models: MIG/MAG 180/35 ET Combi MIG/MAG 200/35 ET Pos. Description Order No. Welding torch SB 15/2 3 090 200 9949 Welding torch SB 15/2 4 090 200 9957.
MIG W elding T orch SB 25/2 For models: MIG/MAG 230/40 ET Pos. Description Stock-No. 100 Contact tip M6 - 1.0 mm Aluminium 132 700 9709 100 Contact tip M6 - 1.
D DEUTSCH ENG ENGLISH KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY Wir erklären in alleiniger Verantwortlichkeit, daß dieses Produkt mit den folgenden Normen übereinstimmt* gemäß den Bestimmungen der Richtlinien**.
Country; Company; Address 1; Address 2; City; Phone; Fax; E-mail Albania; Extra Industrial Goods; Rl. Fadil Rada 88; ; Tirana; (+35 5) 42 - 3 30 62; (+355) 42 - 3 30 62; abeqiri@t-onli ne.de Algerie; Haddad Equipement Pro fessionel; 98 A, Site du Lycée ; ; 16012 Rouiba; (+213) 21 - 85 49 05; (+213) 21 - 85 57 72; heprouiba@hotmail.
An important point after buying a device Metabo 170-230 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Metabo 170-230 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Metabo 170-230 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Metabo 170-230 you will learn all the available features of the product, as well as information on its operation. The information that you get Metabo 170-230 will certainly help you make a decision on the purchase.
If you already are a holder of Metabo 170-230, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Metabo 170-230.
However, one of the most important roles played by the user manual is to help in solving problems with Metabo 170-230. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Metabo 170-230 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
