Instruction/ maintenance manual of the product C45 McIntosh
Go to page of 36
C45 Owner ’s Manual McIntosh Laboratory , Inc. 2 Chambers Street Binghamton, New Y ork 13903-2699 Phone: 607-723-3512 F AX: 607-724-0549 Audio Control Center.
2 IMPOR T ANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERA TING THIS EQUIPMENT . W ARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT T O RAIN OR MOISTURE.
3 Customer Service T echnical Assist ance Please T ake A Moment Thank Y ou Copyright 2003 © by McIntosh Laboratory , Inc. The serial number , purchase date and McIntosh Dealer name are important to you for possible insurance claim or future service.
4 XLR Connectors Below is the Pin configuration for the XLR Balanced Input and Output Connectors on the C45. Refer to the diagram for connection: PIN 1: Shield/Ground PIN 2: + Signal PIN 3: - Signal Power Contr ol and T rigger Connectors The C45’ s Power Control Outputs provide a 5 volt signal.
5 • • • • • Balanced Inputs and Outputs One pair of Balanced high level Inputs and a six channel Balanced Output are provided. • • • • • Precision T racking V ariable Rate V olume Control V olume levels are controlled by a new Multi-Stage Precision Digitally Controlled Attenuator System with a tracking ac- curacy of 0.
6 Dimensions The following dimensions can assist in determining the best location for your C45. There is additional information on the next page pertaining to installing the C45 into cabinets. Dimensions 17- 1/2 " 44.45cm 4- 5/8 " 1 1.75cm 6" 15.
7 Installation The C45 can be placed upright on a table or shelf, standing on its four feet. It also can be custom installed in a piece of furniture or cabinet of your choice. The four feet may be removed from the bottom of the C45 when it is custom in- stalled as outlined below .
8 Rear Panel Connections Connect the power cord to a live AC outlet. Refer to in- formation on the back panel of the C45 to determine the correct voltage External KEYP AD or Sensor Jack per- mits the .
9 McIntosh DVD-Audio Player McIntosh Power Amplifier How to Connect for Power Control McIntosh CD Player How to Connect for Power Control McIntosh Power Control The three Power Control Jacks have default settings as ex- plained on page 8. The hookup example below utilizes the default settings.
10 How to Connect for Dat a Control and Remote Operation Data Control Connections facilitate the ability to remotely operate McIntosh Source Components using the supplied C45 Audio Control Center Remote Control.
11 in out The C45 Audio Control Center has assignable Inputs. Be- fore the Balanced and Phono Inputs can be used, they must be first selected in the Setup Mode, refer pages 15, 17 and 18. 1. Connect Audio Cables from the McIntosh C45 RF and LF Balanced OUTPUTS to the McIntosh Power Ampli- fier Balanced INPUTS.
12 McIntosh T wo Channel Power Amplifier Number T wo How to Connect for Six Channel Operation The C45 Audio Control Center has assignable Inputs. Be- fore the Balanced and Phono Inputs can be used they must be first selected in the Setup Mode. Refer pages 15, 17 and 18.
13 How to Connect for Six Channel Operation in out McIntosh DVD-Audio Player McIntosh CD Player T ape Deck Turntable McIntosh Powered Subwoofer.
14 Front Panel Controls, Displays, Push-Buttons, and Switch Main Switch turns all AC power com- pletely On or Off Selects various Pro- gram Sources for lis- tening and is used dur- ing the entering or.
15 How to Operate the Setup Mode Y our McIntosh C45 has been factory configured for default operating settings that will allow immediate enjoyment of superb audio without the need for further adjustments.
16 Display Brightness The Front Panel Alphanumeric DISPLA Y Brightness may be varied from a setting of 1 (Dim) to 15 (Bright). Follow the steps below for reducing the Display Brightness. Refer to figure 4. 1. Press the SETUP Push-button to access the Setup Mode.
17 Setup, con’t Figure 10 Figure 1 1 T uning Method Description TUNE - Allows for Manual Tuning Up or Down the radio dial. PRESETS - Allows selection of a radio station preset from a previously stored station in memory . SEEK - Automatically scan the dial and will stop on the next available station.
18 6. Press the TRIM LEVEL UP S or Down T T T T T Push-button until the Front Panel Alphanumeric Display indicates “LEVEL 0.0 TUN”. 7. Rotate the INPUT Clockwise until the display indicates “LEVEL 0.
19 Setup, con’t Figure 21 2 Channel Sub The C45 has both Balanced and Unbalanced SUBwoofer Outputs. If either one of the 6 Channel Inputs are selected, the C45 Amplifies the signal at the SUBwoofer Input and makes it available at the SUBwoofer Output.
20 Setup, con’t Remote Control Selection The C45 will respond to two different sets of the Remote Control Codes. The Remote Control included with the C45 utilizes the NORMal McIntosh Control Codes. The Second Set of Control Codes the C45 will respond to is referred to as the AL T ernate Codes.
21 The McIntosh C45 Audio Control Center has been factory configured for operating settings that allow immediate en- joyment of superb high fidelity audio without the need for further adjustments. If you wish to make changes to the fac- tory default settings, refer to the SETUP Section of this Owner ’ s Manual starting on page 15.
22 TRIM push-button until the word and number “BALANCE 00” appears on the Alphanumeric Display , then press the TRIM LEVEL Up S or Down T Push-button to emphasize the Left Channel or the Right Channel. Refer to figures 35a, 35b and 41. The Front Panel Display indicates the balance changes in steps from 0 to 107.
23 How to Operate the C45, con’t Refer to figure 37. 6. Press and release the TRIM Push-button until “SUR- ROUND 0.0” appears on the Front Panel Display . 7. Press the LEVEL Down T T T T T Push-button until “SUR- ROUND -8.5” appears on the Front Panel Display .
24 Remote Control Push-Buttons Selects one of the twelve High Level Audio/V ideo Sources or Phono Input T urns AC Power ON or OFF to certain McIntosh Components when connected via the Data Port Adjust.
25 How to Operate by Remote Control The supplied Remote Control is capable of directly control- ling the functions of contemporary McIntosh Source Com- ponents connected to the C45.
26 Frequency Response +0, -0.5dB from 20Hz to 20,000Hz T otal Harmonic Distortion 0.002% maximum from 20Hz to 20,000Hz at rated output Signal T o Noise Ratio Phono: 86dB below 10mV input (A W eighted) High Level: 96dB below rated output (A W eighted) Rated Output V oltage 2.
27 • • • • • Special FM RF Amplifier Double-Diffused Metal Oxide Field Ef fect T ransistor (DMOS-FET) RF amplifier increases sensitivity and Cross Modulation rejection.
28 75ohm FM ANT (Antenna) connects to an external FM antenna or cable AM ANT (An- tenna) connector allows a McIntosh Remote Antenna to be connected RAA1 Remote Antenna can be adjusted to a position fo.
29 FM Antenna 1. Connect the Remote AM antenna by plugging the DIN connector of the supplied 3 conductor cable into the AM ANT , DIN socket on the back panel of the C45. Note: If a longer length cable needs to be used between the C45 and the RAA1, use a 2 conductor shielded cable.
30 The McIntosh C45 TM1 AM/FM T uner Module incorpo- rates an advanced design AM/FM T uner with many desir- able performance features to enhance your enjoyment of ra- dio broadcasts. There are three methods of tuning AM/FM Broadcast Stations using the Front Panel Tune Push-buttons and four methods using the Remote Control.
31 How to Assign T uner Presets Figure 44 S tation Signal Strengh FM S tereo Signal S tation Frequency Broadcast Band Preset Number The C45 AM/FM T uner Module (TM1) allows for preset- ting radio stations into memory . Refer to figure 44 and per- form the following the below steps to enter stations: 1.
32 How to Optimize AM Reception The McIntosh RAA1 Remote AM Antenna is designed to provide the best in AM Reception especially if the C45 is located in a noisy reception area. Locate the RAA1 away from all electronic and electrical interference sources.
33 Notes.
34 FM T uner Specifications Useable Sensitivity 14dBf which is 1.4uV across 75 ohms 50dB Quieting Sensitivity Mono: 19dBf which is 2.4uV across 75 ohms Stereo: 35dBf which is 15uV across 75 ohms Signa.
35 Packing Instructions In the event it is necessary to repack the equipment for ship- ment, the equipment must be packed exactly as shown be- low . It is very important that the four plastic feet are at- tached to the bottom of the equipment. This will ensure the proper equipment location on the bottom pad.
McIntosh Part No. 04088702 McIntosh Laboratory , Inc. 2 Chambers Street Binghamton, NY 13903 The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.
An important point after buying a device McIntosh C45 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought McIntosh C45 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data McIntosh C45 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, McIntosh C45 you will learn all the available features of the product, as well as information on its operation. The information that you get McIntosh C45 will certainly help you make a decision on the purchase.
If you already are a holder of McIntosh C45, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime McIntosh C45.
However, one of the most important roles played by the user manual is to help in solving problems with McIntosh C45. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device McIntosh C45 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
