Instruction/ maintenance manual of the product 2008 Tribute HEV Mazda
Go to page of 312
Introduction 4 Instrument Cluster 20 W arning lights and chimes 20 Gauges 25 Entertainment Systems 27 Auxiliary input jack (Line in) 35 Satellite radio information 38 Navigation system 41 Climate Cont.
Seating and Safety Restraints 97 Seating 97 Safety restraints 105 Airbags 120 Child restraints 135 Tires, Wheels and Loading 147 T ire information 149 T ire inflation 151 T ire Pressure Monitoring Sys.
Maintenance and Specifications 247 Engine compartment 250 Engine oil 253 Battery 256 Engine Coolant and Motor/Electronics Coolant 258 Fuel information 264 Air filter(s) 278 Maintenance product specifi.
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
W ARNING: Fuel pump and high voltage battery shut-off switches: In the event of an accident the fuel pump shut-off switch may automatically cut off the fuel supply to the engine and the high voltage shut-off switch cuts of f power from the high voltage battery .
Drive your new vehicle at least 500 miles (800 km) before towing a trailer . For more detailed information about towing a trailer , refer to T railer towing in the T ires, Wheels and Loading chapter . Do not add friction modifier compounds or special break-in oils since these additives may prevent piston ring seating.
Stopping: The gas engine may shut off to conserve fuel as you come to a stop. Restarting the vehicle is not required. Simply step on the accelerator when you are ready to drive.
If the vehicle is left inoperative for over 31 days, it may be necessary to jumpstart the vehicle. For more information, refer to Jump starting your (Low voltage [underhood] battery only) in the Roadside Emergencies chapter . Engine: The engine speed in your hybrid is not directly tied to your vehicle speed.
Driving to optimize fuel economy Y our fuel economy should improve throughout your hybrid’ s break-in period. As with any vehicle, fuel economy can be significantly impacted by your driving habits and accessory usage. For best results, keep in mind these tips: T ire Inflation: Keep tires properly inflated and only use recommended size.
Frequently asked questions Question Answer What is the pumping sound I hear when I unlock or enter the vehicle, and the venting sound a few minutes after shutting off my vehicle? This is the hydraulic portion of your regenerative braking system pressurizing and depressurizing.
Question Answer Why does my engine never shut down above 40 mph (64 km/h)? The engine is required to turn on above this speed to protect the transaxle hardware.
Question Answer What is the fan noise and slight tapping sound I hear from the rear of my hybrid? The fan noise comes from two fans located inside the high voltage battery .
Question Answer Can you charge the battery with a plug into an A/C outlet? There are no provisions for charging the high voltage battery from a power supply external to the vehicle.
Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. W ARNING: Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury .
T o access this information, special equipment must be directly connected to the recording modules. Mazda Motor Corporation and Mazda Canada do not access event data recorder information without obtai.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Manual Protecting the Environment Fasten Seat Belt Airbag - Front Airbag - Side Passenge.
V ehicle Symbol Glossary Rear W indow Defrost/Demist Power W indows Power W indow Lockout Personal Alarm System Feature Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Batte.
Multi-function lever (pg. 58) Instrument cluster (pg. 20) Hazard flasher control (pg. 202) Headlamp control (pg. 47) Parking brake release (pg. 189) Speed controls* (pg.
Climate controls (pg. 42) Audio system (pg. 27) Auxiliary input jack (pg. 35) Auxiliary power point (pg. 61) *if equipped 2008 Tribute Hybrid (thv) Owners Guide (post-2002-fmt) USA (fus) Instrument Cl.
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a safety hazard or a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions.
W ARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Check fuel cap: Illuminates when the fuel cap may not be properly installed.
Airbag readiness: If this light fails to illuminate when the ignition is turned to RUN, continues to flash or remains on, have the system serviced immediately by your authorized dealer . A chime will also sound when a malfunction in the supplemental restraint system has been detected.
Engine oil pressure: Illuminates when the oil pressure falls below the normal range, refer to Engine oil in the Maintenance and Specifications chapter . Engine or motor electronic coolant temperature: Illuminates when the coolant temperature exceeds the threshold.
Low fuel: Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is engaged. T urns off when the speed control system is disengaged. Anti-theft system: Flashes when the SecuriLock™ Passive Anti-theft System has been activated.
T ransmission not in park chime: Sounds when the PRNDL is not in P (Park) position, the driver’ s door is ajar and the ignition is in the RUN position. HEV Engine off Reminder Chime: Sounds for 10 seconds when the PRNDL is in the P (Park) position and the Driver’ s door is ajar (open) while ignition is in the RUN position.
Battery gauge: Provides information about the vehicle’ s energy usage. • ASSIST — Battery provides extra power to boost the vehicle’ s acceleration. • CHARGE — Storing extra energy in the battery when coasting or slowing down. Odometer: Registers the total miles (kilometers) of the vehicle.
AUDIO SYSTEMS AM/FM/single CD/in-dash CD6/MP3 satellite compatible sound system Accessory delay: Y our vehicle is equipped with accessory delay . W ith this feature, the window switches, radio and moon roof (if equipped) may be used for up to ten minutes after the ignition is turned off or until either front door is opened.
For a CD6 system, press EJECT and select the desired CD slot by pressing the corresponding memory preset #. The display will read EJECTING #. When the system has ejected the CD, the display will read REMOVE CD #. Remove the CD. If you do not remove the CD the system will reload the disc.
F ADE: Press SOUND repeatedly to reach the fade setting. Press SEEK/TRACK to adjust the audio between the back (B) and front (F) speakers. SPEED COMPENSA TED VOLUME (if equipped): Press SOUND repeatedly to reach the SPEED COMPENSA TED VOLUME setting.
display . After a category is selected, press SEEK to search for that specific category of channels only (i.e. ROCK). Y ou may also select CA TEGORY ALL to seek all available SIRIUS categories and channels. Press OK to close and return to the main menu.
stations without losing your original manually set preset stations for AM/FM1/FM2. T o activate the autoset feature, toggle AUTOSET to ON, and either wait five seconds for the search to initiate or press OK to immediately initiate the search. (If you press another control within those five seconds, the search will not initiate.
9. SA T (Satellite Radio, if equipped): Press SA T to access satellite radio mode, if equipped. Press repeatedly to cycle through SA T1, SA T2 and SA T3 modes. 10. CD: Press to enter CD/MP3 mode. If a disc is already loaded into the system, CD/MP3 play will begin where it ended last.
In MP3 mode, press FOLD and then press / to access the previous/next folder . In satellite radio mode (early availability — if equipped), use to select from various satellite radio categories. T o change categories in satellite radio mode, press CA T/FOLD.
For a CDX6 system, the system will shuffle between all loaded discs. The disc # will appear in the top left hand corner of the display . 16. SCAN: In radio mode, press for a brief sampling of all strong radio stations. In CD/MP3 mode, press for a brief sampling of all tracks on the current disc or folder .
will prompt you to load discs for the remaining available slots. Insert the discs, one at a time, label side up, when prompted. Once loaded, the disc in preset #1 will begin to play . 19. CD slot: For a single CD system, insert a CD/MP3, label side up.
3. Attach one end of the audio extension cable to the headphone output of your player and the other end of the audio extension cable to the AIJ in your vehicle. 4. T urn the radio on, using either a tuned FM station or a CD loaded into the system. Adjust the volume to a comfortable listening level.
GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.
CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players. Do not use any irregular shaped CDs or discs with a scratch protection film attached.
• Antenna obstructions: For optimal reception performance, keep the antenna clear of snow and ice build-up and keep luggage and other material as far away from the antenna as possible.
Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly .
Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly . NO TEXT Category information not available. Category information not available at this time on this channel.
DUAL AUTOMATIC TEMPERATURE CONTROL 1. AUTO/Driver temperature: Press to engage full automatic operation. The system will automatically determine fan speed, airflow distribution, A/C on or off, and outside or recirculated air , to heat or cool the vehicle to reach the desired temperature.
4. Defrost/Floor: Distributes air through the windshield defroster vents, demister vents, floor vents and rear seat floor vents. The system will automatically provide outside air to reduce window fogging. On days where the outside temperature is approximately freezing or higher , the engine will run continuously in this mode.
12. ECON: Press to activate/deactivate economy air conditioning operation. ECON mode may provide improved fuel economy by preventing the gasoline engine from running for the sole purpose of providing A/C. When the gas engine turns off, the A/C compressor does not operate to cool the cabin and comfort may be reduced.
For maximum cooling performance: • Automatic operation: 1. Press AUTO for full automatic operation. 2. Do not override A/C or (recirculated air). 3. Set the temperature to 60°F (16°C). Make sure ECON mode is deactivated. • Manual operation: 1. Select A/C.
REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel and works to clear the rear window of fog and thin ice. The ignition must be in the 3 (RUN) position to operate the rear window defroster . Press R to turn the rear window defroster on.
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Autolamp delay system (if equipped) If your vehicle is equipped with autolamps, you can set the delay time to keep the headlights on for up to three minutes after the key is turned OFF .
High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the lowbeam headlamps on with a reduced output.
P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation.
3. T urn on the low beam headlamps to illuminate the wall or screen and open the hood. Cover the left-hand headlamp with an opaque cloth. 4. On the wall or screen you will observe a light pattern with a distinct horizontal edge of high intensity light towards the right.
INTERIOR LAMPS Dome lamps and map lamps The front dome lamp is located overhead between the driver and passenger seats. The dome lamp control has three positions: • OFF: In this position, the lamp will not illuminate.
Cargo and dome lamp Rear cargo lamp equipped with an ON/OFF/DOOR control will light when: • the doors are closed and the control is in the ON position. • the control is in the DOOR position and any door is open. When the control is in the OFF position, it will not illuminate when you open the doors.
Function Number of bulbs T rade number Backup lamp 2 921 Foglamp (front) 2 9145 Center High-mount stop lamp 5 W5WL Rear license plate lamp 2 168 All replacement bulbs are clear in color except where noted. T o replace all instrument panel lights - see your authorized dealer Replacing the interior bulbs Check the operation of all bulbs frequently .
5. Disconnect the electrical connector from the bulb. W ARNING: Children and Halogen Bulbs: Playing with a halogen bulb is dangerous. Serious injuries could be caused by dropping a halogen bulb or breaking in some other way . Always keep halogen bulbs out of the reach of children.
7. Carefully install the tail lamp assembly on the vehicle and secure with two screws. Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the OFF position. 2. Depress the lever and carefully pry the license plate lamp assembly (located above the license plate) from the liftgate.
3. Pull the bulb straight out of the socket and push in the new bulb. T o complete installation, follow the removal procedure in reverse order . Replacing foglamp bulbs (if equipped) 1. Make sure the foglamp switch is in the OFF position. 2. From underneath the vehicle, rotate the harness/bulb assembly counterclockwise, to remove from the fog lamp.
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid.
Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position. Select: INT 2 — Normal speed operation of rear wiper . INT 1 — Intermittent operation of rear wiper . OFF — Rear wiper and washer off.
W ARNING: Adjusting the steering wheel while the vehicle is moving is dangerous. Moving it can very easily cause the driver to abruptly turn to the left or right. This can lead to loss of control or an accident. Never adjust the steering wheel while the vehicle is moving.
The tray and inside bin can be removed to open up space to fit a laptop computer , MP3 players, CDs or handbags. T o remove, open the console lid and pull the bin straight up and out from the console housing. The sliding tray and inside bin can be hooked on the side or rear of the console for extra storage.
The auxiliary power point is located in the instrument panel. A second auxiliary power point is located on the rear side of the center console. Do not use the power point for operating the cigarette lighter element (if equipped). T o prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W .
Note: The 110 V AC power point is equipped with a safety cap and a safety twist tab. They both provide protection from inserting any object into the power point other than the 110 V AC electrical device plug. The safety cap should always be in a closed position whenever the power point outlet is not in use.
Indicator light Code Green light is On — Power point is ready to supply power Green light is Off — Power point power supply is off. Ignition is not in RUN position Green light is blinking — Power point is in fault mode POWER WINDOWS W ARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows.
Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls (except for the driver’ s) press the right side of the control.
Electronic compass (if equipped) The compass heading is displayed as one of N, NE, E, SE, S, SW , W and NW in the center stack display . The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna.
4. Press and hold the reset button on the compass module for approximately 5 seconds until ZONE XX appears in the center stack display . 5. Continue to press the reset button until the correct zone appears in the center stack display . 6. The direction will display after the button is released.
EXTERIOR MIRRORS Power side view mirrors T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror . 2. Move the control in the direction you wish to tilt the mirror .
CRUISE CONTROL/SPEED CONTROL (IF EQUIPPED) W ith cruise control/speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal.
• If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage. Disengaging speed control T o disengage the speed control: • Depress the brake pedal Disengaging the speed control will not erase previous set speed.
Reducing speed while using speed control There are three ways to reduce a set speed: • Press and hold the SET - control until you get to the desired speed, then release the control. • Press and release the SET - control to operate the T ap-Down function.
STEERING WHEEL CONTROLS (IF EQUIPPED) W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Mazda strongly recommends that drivers use extreme caution when using any device that may take their focus off the road.
In any mode: • Press VOL + or - to adjust the volume. MOON ROOF (IF EQUIPPED) W ARNING: Do not let children play with the moon roof or leave children unattended in the vehicle.
If you open and close the moon roof repeatedly , the moon roof motor may overheat and shut down for 45 seconds while the motor cools. MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the RUN position, the message center , located on your instrument cluster , displays important vehicle information through a constant monitor of vehicle systems.
Distance to empty (DTE) Selecting this function from the INFO menu will give you an estimate of how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling your vehicle. Otherwise, the display will not show the addition of fuel for a few miles (kilometers).
Y our vehicle must be moving to calculate instantaneous fuel economy . When your vehicle is not moving, this function shows , one or no bars illuminated. Instantaneous fuel economy cannot be reset. Electric Energy Select this function from the INFO menu for the state of charge of the high voltage battery .
Pressing the RESET control cycles the message center through each of the systems being monitored. If you don’t press any button, the system will cycle itself. The sequence of the system check report is as follows: 1. Oil life 2. Electric drive 3. Brake system 4.
Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change the message display from English to Metric. Autolamp delay This feature keeps your headlights on for up to three minutes after the ignition is switched off.
Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. W aiting 4 seconds or pressing the RESET control cycles the message center through each of the language choices. Selectable languages are English, Spanish, or French.
W arnings Status Stop safely now W arning returns after 10 minutes if condition still exists High engine temperature High motor temperature Park brake engaged XXX miles (km) to empty fuel level low Liftgate/Glass ajar W arning returns after the ignition key is turned from OFF to RUN.
W ARNING: When the engine and radiator are hot, scalding coolant and steam may shoot out under pressure and cause serious injury . Do not remove the cooling system cap when the engine and radiator are hot. HIGH MOTOR TEMPERA TURE. Displayed when the motor electronics are overheating.
Understanding Y our T ire Pressure Monitoring System in the T ires, Wheels and Loading chapter . If the warning stays on or continues to come on, have the system inspected by your authorized dealer XX% OIL LIFE CHANGE SOON/OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 10% or less.
CARGO AREA FEATURES Cargo shade (if equipped) If your vehicle has a cargo shade, you can use it to cover items in the cargo area of your vehicle. T o install the shade: • Insert the ends of the cargo shade into the mounting features located behind the rear seat on the rear trim panels.
LUGGAGE RACK Y our vehicle is equipped with a roof rack. The maximum load for the roof rack is 100 lbs (44 kg), evenly distributed on the cross-bars. If it is not possible to evenly distribute the load, position it in the center or as far forward on the cross-bars as possible.
2. Slide the cross-bar to the end of the rail. 3. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar . 4. Slide the cross-bar assembly off the end of the rail. T o reinstall the cross-bar assembly (if equipped) to the roof rack side rails: 1.
KEYS Y our vehicle is equipped with two Integrated Keyhead T ransmitters (IKT s). The IKT functions as both a programmed ignition key that operates all the locks and starts the vehicle, and a remote keyless entry transmitter . Y our IKT s are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start.
POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Door key unlocking/locking Unlocking the doors T urn the key in the door cylinder to unlock the driver’ s door only . All other doors will remain locked.
REMOTE ENTRY SYSTEM (IF EQUIPPED) The Integrated Keyhead T ransmitter (IKT) complies with part 15 of the FCC rules and with RSS-210 of Industry Canada.
2. Press and release again within three seconds to unlock the passenger doors, the liftgate and liftgate glass. The battery saver feature will turn off the interior lamps 10 minutes after the ignition is turned to the 1 (OFF/LOCK) position.
Sounding a panic alarm Press and hold for 1.5 seconds to activate the alarm. T o deactivate the feature, press the control again, turn the ignition to the 3 (RUN) or 4 (ST ART) position, or wait for the alarm to time out in approximately 3 minutes. Note: The panic alarm will only operate when the ignition is in the 1 (LOCK) position.
Replacing lost Integrated Keyhead T ransmitters (IKT s) If you would like to have your Integrated Keyhead T ransmitters reprogrammed because you lost one, or would like to buy additional IKT s, you can either reprogram them yourself, or take all IKT s to your authorized dealer for reprogramming.
• T ail lamps The lamps will automatically turn off: • if the ignition switch is turned to the 3 (RUN) position, or • the IKT (lock) control is pressed, or • after 25 seconds of illumination. Note: On some vehicles, the perimeter lamps illuminated entry feature will not activate in daylight conditions.
8. T urn the ignition to the 1 (LOCK) position to exit the procedure. Note: The horn will chirp once to confirm the procedure is complete. SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM SecuriLock™ passive anti-theft system is an engine immobilization system.
If a problem occurs with the SecuriLock™ system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (RUN) position. If this occurs, the vehicle will not start and should be taken to an authorized dealer for service.
portion of the IKT to your vehicle. Note : A maximum of eight coded keys can be programmed to your vehicle; only four of these eight can be IKT s with remote entry functionality . T ips: • Only use Integrated Keyhead T ransmitters (IKT s) or standard SecuriLock™ keys.
8. T urn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least six seconds. 9. Remove the newly programmed coded key from the ignition.
FRONT SEATS Notes: W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s seat belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Push side control and push down on head restraint to lower it. Adjusting the front manual seat (if equipped) Lift handle to move seat forward or backward.
Adjusting the front power seat (if equipped) W ARNING: Never adjust the driver’ s seat or seatback when the vehicle is moving. Y ou could move out of position to control the vehicle. Then a serious accident could occur . Sudden braking or a collision could cause serious injury .
The control is located on the outboard side of the seat cushion. Move the front of the control up or down to raise or lower the front portion of the seat cushion. Move the rear of the control up or down to raise or lower the rear portion of the seat cushion.
REAR SEATS Head restraints The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
2. Place the head restraint under the front seat for storage. 3. Pull the seat release control. Note: Make sure the floor is clear of all objects before folding the seat.
Attach the seat belt web snap button to the quarter trim panel snap button. This will ensure that seat belt does not get caught by staying out of the seat back folding path. 5. T o release seatback, pull the seatback release lever (on top of seat) toward the front seat.
Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place and the red seat unlatched indicator on release paddle is not visible.
W ARNING: Remove the head restraint stored under the front set and return it to the original position on the seatback. Failure to do so could result in personal injury . 3. Unsnap the seat belt webbing from the quarter trim panel. T o remove the rear cushion 1.
analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.
Front crash severity sensor The front crash severity sensor enhances the ability to detect the severity of an impact. Positioned up front, it provides valuable information early in the crash event on the severity of the impact.
technology , parents are STRONGL Y encouraged to always properly restrain children in the rear seat. The sensor also turns off the passenger front airbag and seat-mounted side airbag (if equipped) when the passenger seat is empty to prevent unnecessary replacement of airbag(s) after a collision.
seat belt pretensioners, front seat belt buckle sensors, driver seat position sensor , and front passenger sensing system. In addition, the RCM also monitors the restraints warning light in the instrument cluster . A difficulty with the system is indicated by one or more of the following.
W ARNING: In a rollover crash, an unbelted person is significantly more likely to die or be seriously injured than a person wearing a seat belt. W ARNING: Each seating position in your vehicle has a specific seat belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair .
2. T o unfasten, push the release button and remove the tongue from the buckle. Energy Management Feature • This vehicle has a seat belt system with an energy management feature at the front outboard seating positions to help further reduce the risk of injury in the event of a head-on collision.
How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
W ARNING: BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked by an authorized dealer . Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.
W ARNING: The driver and front passenger seat belt system (including retractors, buckles and height adjusters) must be replaced if the vehicle is involved in a collision that results in deployment of front airbags, seat-mounted side airbags and Safety Canopy™, and seat belt pretensioners.
W ARNING: Failure to inspect and if necessary replace the seat belt assembly under the above conditions could result in severe personal injuries in the event of a collision. For proper care of soiled seat belts, refer to Interior in the Cleaning chapter .
Both the driver’ s and passenger’ s seat belt usages are monitored and either may activate the Belt-Minder 威 feature. The warnings are the same for the driver and the front passenger .
The following are reasons most often given for not wearing seat belts (All statistics based on U.S. data): Reasons given... Consider ... ⬙ Crashes are rare events ⬙ 36700 crashes occur every day . The more we drive, the more we are exposed to ⬙ rare ⬙ events, even for good drivers.
W ARNING: Do not sit on top of a buckled seat belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. T o do so may adversely affect the performance of the vehicle’ s air bag.
1. T urn the ignition switch to the RUN (or ON) position. (DO NOT ST ART THE ENGINE) 2. W ait until the seat belt warning light turns off. (Approximately 1 minute) • Step 3 must be completed within 50 seconds after the seat belt warning light turns off.
AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the seat belt to help protect the driver and right front passenger from certain upper body injuries.
W ARNING: The driver should always hold onto only the rim of the steering wheel. Never place your arm over the airbag module or anywhere inside the rim as a deploying airbag can result in serious arm fractures or other injuries.
Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.
The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic.
W ARNING: If the airbag has deployed, the airbag will not function again and must be replaced immediately . If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Note : The indicator lamp will illuminate for a short period of time when the ignition is turned to the ON position to confirm it is functional. When the front passenger seat is not occupied (empty seat) or in the event that the front passenger frontal airbag is enabled (may inflate), the indicator lamp will be unlit.
Occupant Pass Airbag Off Indicator Lamp Passenger Airbag Empty seat Unlit Disabled Small child in child safety seat or booster Lit Disabled Small child with seat belt buckled or unbuckled Lit Disabled Adult Unlit Enabled W ARNING: Even with Advanced Restraints Systems, children 12 and under should be properly restrained in the back seat.
Objects Pass Airbag Off Indicator Lamp Passenger Airbag Small (i.e. 3 ring binder , small purse, bottled water) Unlit Disabled Medium (i.e. heavy briefcase, fully packed luggage) Lit Disabled Empty se.
In case there is a problem with the front passenger sensing system, the airbag readiness lamp in the instrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects that may be lodged underneath the front passenger seat or cargo interfering with the seat.
A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard.
How does the side airbag system work? The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group.
to inflate in side-impact collisions, not roll-over , rear -impact, frontal or near -frontal collisions, unless the collision causes sufficient lateral deceleration. W ARNING: Several airbag system components get hot after inflation. Do not touch them after inflation.
W ARNING: Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying side-curtain airbags (if equipped). Failure to follow these instructions may increase the risk of personal injury in the event of a collision.
How do the side-curtain airbags (if equipped) work? The design and development of the side air curtain system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group.
The side-curtain airbags are mounted to roof side-rail sheet metal, behind the headliner , above the first and second row seats. In certain lateral collisions or rollover events, the side-curtain airbags will be activated, regardless of which seats are occupied.
A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on.
Children and seat belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear seat belts. Follow all the important safety restraint and airbag precautions that apply to adult passengers in your vehicle.
• Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? • Does the lap belt rest low across the hips? • Is the s.
Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
W ARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child.
tether anchors. For more information on top tether straps and anchors, refer to Attaching safety seats with tether straps in this chapter . For more information of LA TCH anchors refer to Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments in this chapter .
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats.
4. Clip the tether strap to the anchor as shown. The arrow in the above graphic points toward the front of the vehicle. W ARNING: If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision.
Y our vehicle has LA TCH anchors for child seat installation at the following locations: The anchors on both sides of the center of the rear seat are provided primarily for child seats at the outboard seats, and are further apart than the pairs of lower anchors for child seat installation at other seats.
If you install a child seat with rigid LA TCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.
NOTICE TO UTILITY V EHICLE AND T RUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
V EHICLE CHARACTERISTICS 4WD and A WD Systems A vehicle equipped with A WD or 4WD has the ability to use all four wheels to power itself. This increases traction which may enable you to safely drive over terrain and road conditions that a conventional two-wheel drive vehicle cannot.
• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition.
government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
Glossary of tire terminology • T ire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry .
Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped).
When weather temperature changes occur , tire inflation pressures also change. A 10°F (6°C) temperature drop can cause a corresponding drop of 1 psi (7 kPa) in inflation pressure. Check your tire pressures frequently and adjust them to the proper pressure which can be found on the Safety Compliance Certification Label or T ire Label.
TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs.
W ARNING: Age T ires degrade over time depending on many factors such as weather , storage conditions, and conditions of use (load, speed, inflation pressure, etc.) the tires experience throughout their lives. In general, tires should be replaced after 6 years regardless of tread wear .
W ARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Mazda.
Important: Remember to replace the valve stems when the road tires are replaced on your vehicle. Note: The use of a different tire can effect the fuel economy of your vehicle. The tire pressure monitoring sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels.
Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of your vehicle to become misaligned or cause damage to your tires. If your vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment.
• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires.
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R .
Compliance Certification Label, which is located on the B-Pillar or the edge of the driver’ s door , for the correct tire pressure for your vehicle. 12.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W ARNING: The T ire Pressure Monitoring System is NOT a substitute for manually checking tire pressure.
When your temporary spare tire is installed When one of your road tires needs to be replaced with the temporary spare, the TPMS system will continue to identify an issue to remind you that the damaged road wheel/tire needs to be repaired and put back on your vehicle.
Low T ire Pressure W arning Light Possible cause Customer Action Required Solid W arning Light T ire(s) under -inflated 1. Check your tire pressure to ensure tires are properly inflated; refer to Inflating your tires in this chapter .
Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use.
any tire is under -inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. SNOW TIRES AND CHAINS W ARNING: Snow tires must be the same size and grade as the tires you currently have on your vehicle.
V ehicle Curb W eight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying.
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
W ARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’ s GVWR and GA WR limitations. Replacement tires with a higher limit than the original tires do not increase the GVWR and GA WR limitations.
• A final example for your vehicle with 1400 lb. (635 kg) of cargo and luggage capacity . Y ou and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years. Measuring the inside of the vehicle with the rear seat folded down, you have room for 12-100 lb.
T railer towing puts additional loads on your vehicle’ s engine, transaxle, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing. Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’ s load limits.
4WD GCWR (Gross Combined W eight Rating)/T railer W eights Engine Maximum GCWR - lb. (kg) T railer W eight Range - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) 2.3L 4980 (2259) 1000 (454) 24 (2.2) Notes: For high altitude operation, reduce GCW by 2% per 1000 ft.
If you use a rental trailer , follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper . T railer brakes Electric, manual, automatic or surge-type brakes, if compatible with the vehicle, are safe if installed properly and adjusted to the manufacturer’ s specifications.
• Do not exceed the GCWR rating or transmission damage may occur . Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your scheduled maintenance information for more information.
Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability , emissions and reliability . Replace the rear axle lubricant any time the axle has been submerged in water .
STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY , allows the electrical accessories such as the radio to operate while the vehicle is not running. 3. RUN, all electrical circuits operational and warning lights will illuminate.
Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine. If the engine idle speed does not slow down automatically , have the vehicle checked.
3. T urn the key to 3 (RUN) without turning the key to 4 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the vehicle 1.
vehicle still does not start, it may require refueling, jump starting, resetting of the fuel pump/high voltage shut-off switches or service. For information on jump starting the vehicle and resetting .
Association (CSA). Use only an extension cord that can be used outdoors, in cold temperatures, and is clearly marked ⬙ Suitable for Use with Outdoor Appliances. ⬙ Never use an indoor extension cord outdoors; it could result in an electric shock or fire hazard.
Make sure system is unplugged and properly stowed before driving the vehicle. While not in use, make sure the protective cover seals the prongs of the engine block heater cord plug.
Using ABS When hard braking is required, apply continuous force on the brake pedal; do not pump the brake pedal since this will reduce the effectiveness of the ABS and will increase your vehicle’ s stopping distance. The ABS will be activated immediately , allowing you to retain steering control during hard braking and on slippery surfaces.
to interact with the anti-lock brake system (ABS). Regenerative braking is disabled when the ABS is activated or the battery is fully charged. Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops.
Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy . STEERING Y our vehicle is equipped with an Electric Power -Assisted Steering (EP AS) system. There is no fluid reservoir to check or fill.
W ARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Utility vehicles and trucks have larger tires and increased ground clearance, giving the vehicle a higher center of gravity than a passenger car .
2. Using a screwdriver or similar tool, carefully pry out the small Brake T ransmission Shift Interlock (BTSI) cover cap located to the right of the gearshift lever .
Understanding the gearshift positions of the electronically-controlled Continuously V ariable T ransaxle (eCVT) P (Park) This position locks the transaxle and prevents the front wheels from turning.
N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle is free to roll; hold the brake pedal down while in this position. Because of the unique nature of the hybrid vehicle, the engine will not start in the N (Neutral) position. The vehicle does not charge the high voltage battery in the N (Neutral) position.
power distribution between the front and rear wheels. It combines transparent all-surface operation with highly capable four -wheel drive. The 4WD system is always active and requires no driver input. It is capable of handling all road conditions, including street and highway driving as well as off-road and winter driving.
• It often may be less risky to strike small objects, such as highway reflectors, with minor damage to your vehicle rather than attempt a sudden return to the pavement which could cause the vehicle to slide sideways out of control or roll over . Remember , your safety and the safety of others should be your primary concern.
Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over -driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency . Excessive steering will result in less vehicle control, not more.
Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall.
Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. A void driving crosswise or turning on steep slopes or hills .
Driving on snow and ice 4WD vehicles have advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control.
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).
HAZARD FLASHER CONTROL The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash.
The fuel pump shut-off switch is located in the front passenger’ s footwell, behind a flip-up cover . The high voltage shut-off switch is located in the cargo area on the passenger side of the vehicle in the jack compartment, behind the jack access door .
If you see or smell fuel, do not reset the fuel pump shut-off or try to start your vehicle; you could injure yourself or others. Have all the passengers get out of the vehicle and call the local fire department or a towing service. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown.
COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 70A — — T an — Brown 80A — — Natural Black Black Passenger compartment fuse panel The fuse panel is located on the right-hand side of the center console, by the instrument panel.
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 30A Not used (spare) 2 15A Brake On/Off switch 3 15A Not used (spare) 4 30A 110V inve.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 28 5A Radio 29 5A Instrument panel cluster 30 5A Not used (spare) 31 10A Compass module 32 10A Restraints control modul.
W ARNING: T o reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the low voltage (underhood) battery or refilling fluid reservoirs.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 10 30A** Front wipers 11 30A** PCM/Power sustain 12 40A** Blower motor 13 10A* A/C clutch 14 10A* Heater/Coolant pump 15 50A** T .
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 31C — Heater pump relay 31D — Coolant pump relay 31E — Not used 31F — Not used 32 — A/C clutch diode 33 — PCM diode 3.
W ARNING: The use of tire sealants may damage your T ire Pressure Monitoring System and should not be used. W ARNING: Refer to T ire Pressure Monitoring System (TPMS) in the T ire, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longer function.
Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability 3.
Stopping and securing the vehicle 1. Park on a level surface, set the parking brake and activate the hazard flashers. 2. Place gearshift lever in P (Park) and turn engine off. Removing the jack and tools The jack and tools are located in the right rear of the cargo area behind an access panel.
T o remove jack from vehicle: 1. Release the thumbscrew on the bracket. 2. Release the retention clip on the upper part of the jack bracket. 3. Dislodge the jack from the bracket and carefully guide jack down and out through trim opening, upper end out first.
If equipped with a tether , perform the following additional steps: 4. Lift the spare tire on end to access tether attachment (1). 5. Use the lug wrench to remove the lug nut from the spare tire tether . 6. If not replacing the spare or flat tire to the underbody storage area, raise winch up into the installed position.
W ARNING: T o help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed. W ARNING: Changing a tire is dangerous if not done properly .
• Front View shown from rear of front tire. Position the jack directly below the protruding bolt. • Rear View shown from forward of rear tire. Position jack directly below the stud on the rear trailing arm.
3. Position the jack according to the guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground. Never use the differentials as a jacking point. W ARNING: T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire.
Stowing the jack and tools Make sure the jack is fully lowered and reclip the tools onto the jack. Reinstall the jack and tools in the cargo area. T o replace the jack in the vehicle, • guide the ja.
1. Place tire on end with valve stem facing rearward, away from vehicle. 2. Place tether into bolt holes in wheel and attach lug nut using lug wrench. 3. Lay the tire on the ground with the valve stem facing down. If your vehicle is equipped with aluminum wheels, remove the wheel ornament.
WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.). Bolt size Wheel lug nut torque* lb.ft. N • m M12 x 1.5 100 135 * T orque specifications are for nut and bolt threads free of dirt and rust.
JUMP STARTING (LOW VOLTAGE [UNDERHOOD] BATTERY ONLY) Y our vehicle has two separate jump starting procedures; the following procedure is for the low voltage (underhood) battery only . Refer to Jump starting the high voltage battery in this chapter for information on jump starting the high voltage battery .
5. T urn the heater fan on in both vehicles to protect from any electrical surges. T urn all other accessories off. Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery .
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system.
Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
JUMP STARTING THE HIGH VOLTAGE BATTERY Y our vehicle has two separate jump starting procedures; the following procedure is for the cargo area high voltage battery only . Refer to the Jump starting your vehicle (Low voltage [underhood] battery only) section in this chapter for information on jump starting the low voltage (underhood) battery .
When the button is pressed, the indicator light on the button will illuminate. After eight minutes has passed, the indicator light will flash rapidly for two minutes.
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment.
If the vehicle is towed by other means or incorrectly , vehicle damage may occur . In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer , or fl.
CUSTOMER ASSISTANCE (U.S.A. MAINLAND AND HAWAII) Y our complete and permanent satisfaction is our business. W e are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
Whatever way you contact us, please help us to serve you more efficiently and effectively by providing the following information: 1. Y our name, address, and telephone number 2. Y ear and model of vehicle 3. V ehicle Identification Number (17 digits, noted on your registration or title or located on the upper driver’ s side corner of the dash) 4.
Provide the Department with the following information: 1. Y our name, address, and telephone number 2. Y ear and model of vehicle 3. V ehicle Identification Number (VIN). Refer to V ehicle identification label in the Maintenance and Specifications chapter of this manual for the location of the VIN.
CAMV AP uses the services of Provincial Administrators to assist consumers in scheduling and preparing for their arbitration hearings. However , before you can proceed with CAMV AP you must follow your Mazda dispute resolution process as outlined previously .
CUSTOMER ASSISTANCE (PUERTO RICO & VIRGIN ISLANDS) Y our complete and permanent satisfaction is our business. That is why all Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition.
IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’ s applicable e.
(Distributor in each area) CANADA Mazda Canada, Inc. 55 V ogell Road Richmond Hill, Ontario L4B 3K5 Canada TEL: 1 (800) 263–4680 (in Canada) (416) 609–9909 (outside Canada) PUERTO RICO & VIRGIN ISLANDS Plaza Motors Corp. (Mazda de Puerto Rico) P .
• Federal Emission Control W arranty – Emission Defect W arranty – Emission Performance W arranty • California Emission Control W arranty (if applicable) • Replacement Parts and Accessories Limited W arranty • T ire W arranty NOTE: Detailed warranty information is provided with your Mazda portfolio.
recommend that you NOT take your Mazda outside Canada. However , in the event that you are moving to the United States permanently , Mazda vehicles built for use in Canada could be eligible for exportation to the United States with specific vehicle modifications to comply with the United States Federal Motor V ehicle Safety requirements.
W ARNING: Add-On Electrical and Electronic Equipment: Incorrectly choosing or installing improper add-on equipment or choosing an improper installer could be dangerous. Essential systems could be damaged, causing engine stalling, air -bag (SRS) activation, ABS inactivation, or a fire in the vehicle.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Mazda Corporation.
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo. • Never use strong household detergents or soap, such as dish washing or laundry liquid.
PAINT CHIPS Y our dealer has touch-up paint to match your vehicle’ s color . T ouch-up paint can be used to repair minor scratches to painted surfaces. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips.
• Cover the highlighted areas to prevent water damage when cleaning the engine. Note: As with all transmissions, be especially careful as water entry into the vents can damage internal parts. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage.
• The wiper blades can be cleaned with isopropyl (rubbing) alcohol or a windshield washer concentrate. This washer fluid concentrate contains a special solution in addition to alcohol which helps to remove the hot wax deposited on the wiper blade and windshield from automated car wash facilities.
• Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials. W ARNING: Do not use chemical solvents or strong detergents when cleaning the seat where the side air bag (if equipped) is mounted.
SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service.
1. High voltage connector shield 2. Service Disconnect 3. High voltage battery case Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. T urn off the engine and remove the key . 3. Block the wheels to prevent the vehicle from moving unexpectedly .
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. 3. Lift the hood open and secure it with the prop rod.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Engine coolant reservoir 2. Motor/Electronics (M/E) coolant reservoir 3. Engine oil filler cap 4. Brake fluid reservoir 5. Power distribution box 6. Low V oltage (underhood) battery 7.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Mazda specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. T urn the blade at a right angle to the arm. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. 3. Attach the new blade to the arm and snap it into place.
T o replace the wiper blade: 1. Grab the wiper arm just below the blade attachment and pull it as far away from the glass as possible. Do not use excessive force because it can break the wiper arm at the heel.
5. Locate and carefully remove the engine oil level dipstick. 6. W ipe the dipstick clean. Insert the dipstick fully , then remove it again. • If the oil level is within the MIN and MAX marks or the lower and upper holes, the oil level is acceptable.
2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity . Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the FULL mark on the engine oil level dipstick.
Change your engine oil and filter according to the appropriate schedule listed in scheduled maintenance information. When changing the oil filter on the 2.3L engine you must also replace the filter cap O-ring. The oil filter drain plug O-ring must also be replaced whenever the oil filter drain plug is removed.
W ARNING: Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes.
6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more to relearn the idle and fuel trim strategy . • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in scheduled maintenance information . The coolant concentration should be maintained at 50/50 coolant and distilled water , which equates to a freeze point of -34°F (-36°C).
Checking motor/electronics (M/E) coolant The M/E coolant reservoir is located behind the engine coolant reservoir . Refer to the following engine coolant sections for all information, instructions and warnings related to cooling systems.
If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty . If the reservoir is low or empty , add engine coolant to the reservoir .
A large amount of water without engine coolant may be added, in case of emergency , to reach a vehicle service location. In this instance, the cooling system must be drained and refilled with a 50/50 mixture of engine coolant and distilled water as soon as possible.
Y our cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage). Recycled engine coolant Mazda Motor Corporation does.
• Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive.
W ARNING: Gasoline may contain benzene, which is a cancer -causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling.
W ARNING: The flow of fuel through a fuel pump nozzle can produce static electricity , which can cause a fire if fuel is pumped into an ungrounded fuel container . Refueling W ARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries.
If the check fuel cap lamp or a “check fuel cap” message come on, the fuel filler cap may not be properly installed. The lamp or message can come on after several driving events after you’ve refueled your vehicle. At the next opportunity , safely pull off of the road, remove the fuel filler cap, align the cap properly and reinstall it.
Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas.
If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal.
2. Each time you fill the tank, record the amount of fuel added (in gallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading.
• Minimize temperature extremes when the vehicle is parked, for example by storing in a garage to avoid extreme cold in winter and extreme sun loads in summer . The high voltage battery operates more efficiently in moderate temperatures. • Combine errands.
EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. T o make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed.
it from working. Information about your vehicle’ s emission system is on the V ehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your W arranty Information Booklet for complete emission warranty information.
Readiness for Inspection/Maintenance (I/M) testing Some state/provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration.
BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Check fluid levels with the ignition in the RUN position. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid.
Note: The brake system on this vehicle can only be bled at a authorized dealer . T RANSMISSION FLUID Checking electronically controlled continuously variable transmission (eCVT) Refer to your scheduled maintenance information chapter for scheduled intervals for fluid checks and changes.
5. Using the hole in the splash shield, remove the check plug from the side of the transmission. If this is the first check of the transmission fluid, it may be necessary to remove the perforated section of the splash shield (as indicated on the splash shield).
7. The fluid level should be within 1/4 inch (6 mm) of the plug threads. 8. Replace the check plug. Adjusting eCVT fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is indicated in the Maintenance product specifications and capacities section in this chapter .
Changing the air filter element 1. Release the clamps that secure the air filter housing cover . 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4. W ipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing.
Changing the high voltage battery air filter element 1. Remove access panel located in the rear cargo area on the driver’ s side trim panel to expose the filter cover . 2. Push the tabs (located on each side of filter cover) while pulling gently to remove filter cover .
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Mazda Part Name or equivalent Application Brake fluid Between MIN and MAX lines on reservoir High Performance DOT 3 Motor V ehicle Brake Fluid Brake fluid reservoir Engine coolant 8.5 quarts (8.
Item Capacity Mazda Part Name or equivalent Application Fuel tank 15 gallons (56.8L) — All 1 Add the coolant type originally equipped in your vehicle.
ENGINE DATA Engine 2.3L I4 engine Cubic inches 140 Required fuel 87 octane Firing order 1-3-4-2 Ignition system Coil on plug Spark plug gap 0.049–0.053 inch (1.
IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint System 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6.
CELL PHONES Use of cell phones and other devices by driver: W ARNING: Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver’ s hands.
GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for your vehicle. Carefully following this schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it.
Mazda strongly recommends the use of genuine Mazda replacement parts. Parts other than Mazda or Mazda authorized remanufactured parts that are used for maintenance replacement or for the service of components affecting emission control must be equivalent to genuine Mazda Motor Corporation parts in performance and durability .
Genuine Mazda Parts and Service When planning your maintenance services, consider your Mazda dealership for all your vehicle’ s needs. Get the most from your service and maintenance visits There are a lot of reasons why visiting your Mazda Dealership for all your service needs is a great way to help keep your vehicle running great.
• Wheel Alignment • Brakes And when your vehicle needs replacement parts, insist that only parts meeting Mazda Motor Corporation’ s specifications are used. Genuine Mazda branded parts meet these specifications. Y ou can find them at your Mazda Dealership.
WHICH MAINTENANCE SCHEDULE SHOULD Y OU FOLLOW? Owner Checks and Services Refer to Mileage Intervals for Additional Checks and Services Certain basic maintenance checks and inspections should be performed by the owner or a service technician at the intervals indicated.
Multi-point Inspection In order to keep your vehicle running right, it is important that you have the systems on your vehicle checked regularly . This can help identify any potential issue before there are any problems.
U.S. AND CANADIAN SCHEDULE 5,000 miles (8,000 km) ❑ Inspect tires for wear and measure tread depth ❑ Rotate tires D EALER V ALIDATION : RO#: P&A C ODE : D ATE :M ILEAGE : 10,000 miles (16,000 .
30,000 miles (48,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth ❑ Rotate tires ❑ Inspect high voltage battery A/C filter, replace if necess.
60,000 miles (96,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth ❑ Rotate tires ❑ Inspect brake pads, shoes, rotors, drums, brake lines and .
90,000 miles (144,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth ❑ Rotate tires ❑ Inspect high voltage battery A/C filter, replace if neces.
120,000 miles (192,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth ❑ Rotate tires ❑ Inspect brake pads, shoes, rotors, drums, brake lines an.
150,000 miles (240,000 km) ❑ Change engine oil and replace oil filter ❑ Inspect tires for wear and measure tread depth ❑ Rotate tires ❑ Inspect high voltage battery A/C filter ❑ Replace engi.
SPECIAL OPERATING CONDITIONS T owing a trailer or using a camper or car-top carrier Every 5,000 miles, 6 months or 200 hours of engine operation (whichever comes first) Change engine oil and replace f.
Special Operating Conditions Log D EALER V ALIDATION : RO#: P&A C ODE : D ATE :M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D ATE :M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D .
Special Operating Conditions Log D EALER V ALIDATION : RO#: P&A C ODE : D ATE :M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D ATE :M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D .
MAZDA PREMIUM GOLD ENGINE COOLANT CHANGE RECORD Current mileage goes here => Add 50,000 miles to the current miles + 50,000 Next change due at this mileage => Or T oday’s date goes here => Add 3 years + 00 / 00 / 03 Date of next change => whichever comes first Dealer Stamp P & A CODE R.
A Accessory delay .......................... 65 Air cleaner filter ............... 278–280 Air conditioning automatic temperature control system ..........................42 Airbag supplemental restraint system ........................120, 129, 131 and child safety seats .
waxing ..................................... 242 wheels ...................................... 243 wiper blades ............................ 244 Climate control (see Air conditioning or Heating) ............42 Compass, electronic ....................66 calibration .
fuel pump/high voltage shut-off switches ....................202 improving fuel economy ........ 269 octane rating ...................268, 283 quality ...................................... 268 running out of fuel ................. 268 safety information relating to automotive fuels .
doors .......................................... 87 Lubricant specifications ...........281 Lug nuts ....................................221 Luggage rack ...............................84 M Manual transmission fluid capacities ........................
Safety Compliance Certification Label .................... 284 Satellite Radio Information ........38 Scheduled Maintenance Guide ......................................... 287 General Maintenance Information ............................. 287 Normal Scheduled Maintenance and Log .
V V ehicle Identification Number (VIN) .......................................... 284 V ehicle loading ..........................170 V entilating your vehicle ...........185 W W arning lights (see Lights) ....... 20 W asher fluid .....................
309.
310.
311.
312.
An important point after buying a device Mazda 2008 Tribute HEV (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Mazda 2008 Tribute HEV yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Mazda 2008 Tribute HEV - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Mazda 2008 Tribute HEV you will learn all the available features of the product, as well as information on its operation. The information that you get Mazda 2008 Tribute HEV will certainly help you make a decision on the purchase.
If you already are a holder of Mazda 2008 Tribute HEV, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Mazda 2008 Tribute HEV.
However, one of the most important roles played by the user manual is to help in solving problems with Mazda 2008 Tribute HEV. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Mazda 2008 Tribute HEV along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
