Instruction/ maintenance manual of the product Stacked Washer/Dryer Maytag
Go to page of 14
printed in U.S .A. 6 3717020 ST A CKED W ASHER-DR YER INST ALLA TION INSTR UCTIONS LEA VE THESE INSTR UCTIONS WITH THE O WNER IMPOR T ANT T O INST ALLER REMO VE THE DOOR FROM ALL DISCARDED APPLIANCES SUCH AS DR YERS AND COMBINA TION W ASHER/DR YERS T O A V OID THE D ANGER OF A CHILD SUFFOCA TING SHOULD HE/SHE CRA WL INSIDE AND THE DOOR BE SHUT .
printed in U.S .A. 1 IMPOR T ANT T O O WNER Retain these instructions for future ref erence. This new Ma ytag appliance is designed to ser ve you dependab ly for man y years . How ev er , it cannot do so unless provided with sufficient electrical power , suitable e xhausting and if a gas model, adequate gas supply .
2 printed in U.S .A. PREINST ALLA TION CONSIDERA TIONS Location: The stack ed washer/dr y er is approv ed f or zero clearance installation on the sides and the back (depending on v enting used).
printed in U.S .A. 3 ALCO VE OR CLOSET INST ALLA TION When the stack ed washer/dr yer is to be installed in an alcov e area or a closet, clearance should be provided around the unit f or an adequate air supply and f or ease of installation and ser vicing.
EXHA UST HOOD TYPE Number of 90° T ur ns Maximum length of 4 inch diameter rigid metal duct 0 54 f eet 44 f eet 1 43 f eet 33 f eet 2 36 f eet 26 f eet 3 30 f eet 20 f eet 4 24 f eet 14 f eet Maximum.
printed in U.S .A. 5 RIGID DUCTW ORK LIMIT A TIONS Rigid metal ductwork should not e xceed 54 feet of straight 4 inch duct. Each 90° elbow and the e xhaust hood should be considered equivalent to 8 f eet of straight ductwork. F or e xample, if an e xhaust hood and two 90° elbows are used, the maxim um straight duct allow ed would be 26 f eet.
6 printed in U.S .A. Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. ADDITIONAL GR OUND PR OCEDURE WHERE LOCAL CODE PERMITS. A grounding kit (P ar t No . 12001875) is av ailable.
printed in U.S .A. 7 4-WIRE RECEPT A CLE F or a 4-wire hook-up , the frame of a 120/240 v olt machine must NO T be connected to neutral ter minals. It MUST be connected to the 4th wire (green) of the po wer supply or to the metallic cov er ing of a 3-wire supply .
8 printed in U.S .A. 36 inch standpipe recommended If standpipe is less than 36 inches (or floor drain) – drain hose should be routed through the clip to raise hose to the proper height, use clip tie to securely hold drain hose in clip .
printed in U.S .A. 9 INST ALLA TION INST ALL DR YER UNIT AND ST AND The dr yer and stand are installed first. With the connections prepared f or e xhausting, electric pow er and gas (if gas stack ed washer/dryer , see page 9), the dr yer and stand are mo ved to the location.
10 printed in U.S .A. DR YER INST ALLA TION A CCESSORIES V ent Kit – standard – 4 ″ (10.16cm) kit includes two elbo ws, three pipes and one v ent hood V ent Hood – 4 ″ (10.16cm) opening Aluminum Pipe – 4 ″ x 24 ″ (10.16cm x 60.96cm) Aluminum Elbo w – 4 ″ (10.
printed in U.S .A. 11 Attach the inlet hoses to the HO T and COLD f aucets. Being sure the hose marked “HO T” is attached to the HO T water f aucet. Tighten by hand until snug and then 2/3 of a tur n with pliers. Do not overtighten. Attach the 90° ends of the inlet hoses to the HO T and COLD connections on the back of the w asher .
12 printed in U.S .A. 10. Connect the dr yer po wer cord to 120 volt A C outlet f or gas models. 240 v olt outlet f or electric models. Make appropriate e xter nal ground connection. See DET AILED Installation Instructions for ELECTRICAL REQUIRE- MENTS AND GROUNDING (pages 6-7).
printed in U.S .A. 13 ADDITIONAL INFORMA TION ODD CYCLE OPERA TION This Ma ytag stack ed washer/dr yer is man uf ac- tured f or operation on 60 Hz approv ed electr ical ser vice. It is not designed for use on 50 Hz A C electrical ser vice and conv ersion of the product from 60 to 50 cycle operation is not recom- mended.
An important point after buying a device Maytag Stacked Washer/Dryer (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Maytag Stacked Washer/Dryer yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Maytag Stacked Washer/Dryer - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Maytag Stacked Washer/Dryer you will learn all the available features of the product, as well as information on its operation. The information that you get Maytag Stacked Washer/Dryer will certainly help you make a decision on the purchase.
If you already are a holder of Maytag Stacked Washer/Dryer, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Maytag Stacked Washer/Dryer.
However, one of the most important roles played by the user manual is to help in solving problems with Maytag Stacked Washer/Dryer. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Maytag Stacked Washer/Dryer along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
