Instruction/ maintenance manual of the product "E" System Mantis
Go to page of 14
© 2006 Mantis, Div . of Schiller -Pfeiffer Inc. All Rights Reserved. Edger “E” System Owner s Manual and Saf ety Instr uctions.
1 T able of Contents Important Information A. Introduction This attachment is fitted with a blade, intended to be used to edge flower beds, sidewalks, driveways, curbs, etc. B. Specification. C. Contents of the package 1. Edge T rimmer Attachment Assembly 2.
2 Safety and W arnings A. Safety Decals Please pay particular attention to the warning and information decals found on various parts of this Edger Attachment unit. They are an important part of the safety system. These decals must be replaced in time due to abrasion, etc.
3 General Safety Rules 1. Never edge while people, especially children or pets are nearby . 2. Before using, always visually inspect to see that the blade, blade bolts and cutter assembly are not worn or damaged. 3. Do not start the motor when a bystander is standing in front of the blade.
Length (feet) 1 to 25 26 to 50 51 to 100 101 to 150 Cord gauge (A WG) 18 16 14 12 4 b. Based on the total length of cord that you are going to use, check the chart to make sure the cord meets the correct minimum cord gauge (A WG) requirements.
5 W ARNING – DANGER IMPROPER ASSEMBL Y OF THIS EQUIPMENT CAN RESUL T IN SERIOUS INJUR Y . MAKE SURE TO FOLLOW ALL INSTRUCTIONS CAREFULL Y . IF YOU HA VE ANY QUESTIONS, CONT ACT MANTIS CUSTOMER SER VICE. 34. Always disconnect power cord from power source: a.
6 T ools: 9 / 16 " wrench, pin supplied with the unit or screwdriver 1. Remove the following parts from the Edge T rimmer Assembly: blade mounting bolt #1 by rotating it clockwise, clamping plate #2, gear case cover #3, holding screws #4, and cover #5.
7 Check the balance of the assembled unit. The handles and shoulder harness have been assembled at the factory and set according to the average sized person.
8 T ools: 9 / 16 " wrench, pin or screwdriver 1. Lock the gear shaft by inserting the pin or screwdriver through the aligned keyholes in the gear case cover and the gear case to prevent rotation (Picture 19).
9 1. Clean. 2. Lubricate for rust prevention. 3. Store indoor . Storage 1. W ith both hands on the handles, push lockout trigger button with your thumb first, and then squeeze trigger . Start edging when blade rotates at full RPM, by lowering the blade gently into the ground.
10 Service Maintenance Guide Area Maintenance procedure Frequency Spline male/female connection of the inner drive shaft Inspect/Lubricate 1. Remove the side screw , and loosen up other three as shown on the diagram (left). 2. Pull the shaft from the gear housing.
11 1 2 3 4 6 5 7 8 20 11 12 24 25 9 10 13 14 15 16 23 22 18 19 21 26 31 29 28 30 32 27 42 39 41 40 34 33 35 36 37 38 44 43 49 58 48 47 46 51 54 55 56 57 53 52 56 45 50 62 60 61 59 63 1 7 Edger “E”.
KEY # DESCRIPTION P ART # QTY 1 GEAR CASE ASSEMBL Y 331 137 1 2 GEAR CASE 331 138 1 3 O-RING 331 139 1 4 BEARING 6201Z 331 140 1 5 SEAL 331 141 1 6 RING RET AINING 331 142 1 7 SHAFT 331 143 1 8 GEAR 3.
Specifications, descriptions, and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice.
An important point after buying a device Mantis "E" System (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Mantis "E" System yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Mantis "E" System - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Mantis "E" System you will learn all the available features of the product, as well as information on its operation. The information that you get Mantis "E" System will certainly help you make a decision on the purchase.
If you already are a holder of Mantis "E" System, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Mantis "E" System.
However, one of the most important roles played by the user manual is to help in solving problems with Mantis "E" System. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Mantis "E" System along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
