Instruction/ maintenance manual of the product STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER Manley Labs
Go to page of 11
MANLEY LABORATORIES, INC. OWNER'S MANUAL STUDIO STANDARD 350 W ATT MONOBLOCK AMPLIFIER.
CONTENTS INTRODUCTION 3 MAINS CONNECTIONS 4 CONNECTING YOUR AMPLIFIER 5 FIGURE 1 FRONT PANEL 6 FIGURE 2 TOP PANEL 7 FIGURE 3 REAR PANEL 8 BIAS PROCEDURES 9 OPERATIONAL NOTES 10 SPECIFICATIONS 11 WARRA.
THANK YOU!... for choosing the Manley Laboratories Studio Standard 350 watt monoblock amplifiers. Designed around the concept that less is more, the Studio Standard 350 uses the best available parts with the shortest, cleanest, signal path possible. With the use of our own C.
MAINS CONNECTIONS Your amplifier has been factory set to the correct mains voltage for your country. The voltage setting is marked on the serial badge, located on the rear panel. Check that this complies with your local supply . Export units for certain markets have a moulded mains plug fitted to comply with local requirements.
CONNECTING YOUR AMPLIFIER Setting up your amplifier is rather easy. 1. Connect all source components (turntable, CD, Tuner, Tape DAT, etc.) to your preamplifier. 2. Connect the interconnects from the output of the preamplifier or switching center to RCA input .
BIAS PROCEDURES The Manley Studio Standard 350 is a fixed bias system that requires very little attention. If you wish to adjust or check the bias, follow the following steps. 1. On diagram 1, which depicts the front panel of the Manley 350, you can see two measurement tip jacks labled "READ BIAS".
OPERATIONAL NOTES SWITCHING ON The power switch is located on the lower right hand corner of the front panel. Push the top of the rocker switch (1) to turn on the amplifier and the bottom of the rocker to turn off the amplifier.
SPECIFICA TIONS Vacuum Tubes: 8 x 6550, 1 x 6350, 1x 12AT7 Output Power 20 Hz - 20 KHz, 4 Ohm Load 380 W 3%T.H.D. feedback MAXIMUM 376 W 3%T.H.D. feedback STANDARD 360 W 3%T.H.D. feedback MINIMUM Slope Adjustment 20 KHz, (Ref. to 0dB @ 1K) +1 dB slope = MINIMUM +0.
W ARRANTY All Manley Laboratories equipment is covered by a limited warranty against defects in materials and workmanship for a period of 90 days from date of purchase to the original purchaser only.
WARRANTY REGISTRATION We ask that you please fill out this registration form and send the bottom half to: MANLEY LABORATORIES REGISTRATION DEPARTMENT 13880 MAGNOLIA AVE. CHINO CA, 91710 Registration entitles you to product support, full warrenty benefits, and notice of product enhancements and upgrades.
NOTES.
An important point after buying a device Manley Labs STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Manley Labs STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Manley Labs STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Manley Labs STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER you will learn all the available features of the product, as well as information on its operation. The information that you get Manley Labs STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER will certainly help you make a decision on the purchase.
If you already are a holder of Manley Labs STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Manley Labs STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER.
However, one of the most important roles played by the user manual is to help in solving problems with Manley Labs STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Manley Labs STUDIO STANDARD 350 WATT MONOBLOCK AMPLIFIER along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
