Instruction/ maintenance manual of the product 6203DWAE Makita
Go to page of 17
Y Cordless Driver Drill Capacities Steel Wood Wood screw Machine screw ____ 10 mm 25 mm , 6.4 mm x 76 mm ,llm 1,,4,,1 1318'7 11") 1114" x 3") Equipped with Electric Brake MODEL 6203DWAE Dimensions Net (L x W x HI No load speed 1RPMI weight ,,200 ~ 4oo 233 mm x 77 mm x 241 mm 1.
GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area *Keep your work area clean and well lit.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Tool Use and Care Use clamps or other practical way to secure and support the workpiece to a stable platform.
Specific Safety Rules 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator.
SYMBOLS The followings show the symbols used for tool. ?.J n A Ab .../ min ........... volts ................................. amperes ................................. hens ................................. seconds ................................. alternating current .
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE I. SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) 25 AWG Size of Cord 18 50 100 150 18 18 16 6.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents.
Installing or removing battery cartridge *Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge.
*If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools.
OPERATION Switch action CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released To start the tool, simply pull the trigger. Tool speed is increased by increasing pres- sure on the trigger.
CAUTION: *Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned half-way between the "I" side and "11" side, the tool may be damaged. *Do not use the speed change lever while the tool is running.
NOTE: *Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. Nominal diameter of wood screw lmm) *When driving wood screws, predrill pilot holes to make driving easier and to pre- vent splitting of the workpiece.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark.
ACCESSORIES 784206-5 784207-3 CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
July-O9-'96 US CORDLESS DRIVER DRILL Model 6203DWA Note: The switch and other part configurations may differ from country to country. 15.
MODEL 6203DWA ';,'OM :&, DESCRIPTION 14 15 16 17 18 19 20 21 22 23 24 25 26 July-19-'96 US ';;M $FD DESCRIPTION 1 1 1 1 1 1 1 1 4 3 2 2 1 10 11 12 13 Name Plate Tapping Screw B.
Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b).
An important point after buying a device Makita 6203DWAE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 6203DWAE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 6203DWAE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 6203DWAE you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 6203DWAE will certainly help you make a decision on the purchase.
If you already are a holder of Makita 6203DWAE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 6203DWAE.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 6203DWAE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 6203DWAE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
