Instruction/ maintenance manual of the product 3707FC Makita
Go to page of 20
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.
2 SPECIFICATIONS • Manuf acturer reser v es the right to change specifications without notice. • Specifications ma y differ from countr y to country . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions.
3 5. A void bod y contact with grounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is g rounded. 6. Do not expose po wer tools to rain or wet conditions. W ater enter ing a pow er tool will increase the risk of electr ic shoc k.
4 SER VICE 23. T ool service must be performed onl y by qualified repair personnel. Service or main- tenance perf ormed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual.
5 9. Before using the tool on an actual w ork- piece, let it run for a while. W atch f or vibration or wobb ling that could indicate improperl y installed bit. 10. Be careful of the bit rotating direction and the feed direction. 11 . Do not leave the tool running.
6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is s witched off and unplugged bef ore adjusting or checking function on the tool. Adjusting bit protrusion T o adjust the bit protrusion, loosen the lev er and mov e the tool base up or down as desired b y tur ning the adjusting roller .
7 NO TE: • Use a dr y cloth to wipe the dir t off the lens of light. Be careful not to scratch the lens of light, or it ma y lower the illumination. ASSEMBL Y CA UTION: • Alwa ys be sure that the tool is s witched off and unplugged bef ore carr ying out any work on the tool.
8 NO TE: • Moving the tool f orward too f ast may cause a poor quality of cut, or damage to the bit or motor . Moving the tool f orward too slowly ma y burn and mar the cut. The proper f eed rate will depend on the bit size, the kind of workpiece and depth of cut.
9 Loosen the screws and remo ve the base protector . Place the templet guide on the base and replace the base protector . Then secure the base protector by tightening the scre ws. Secure the templet to the workpiece. Place the tool on the templet and mov e the tool with the templet guide sliding along the side of the templet.
10 Attach the guide plate to the straight guide with the bolt, the wa ve w asher , the flat washer and the wing n ut. Attach the straight guide with the clamp scre w (A). Loosen the wing nut on the straight guide and adjust the distance between the bit and the straight guide .
11 F or cutting circles between 70 mm (2-3/4 ” ) and 121 mm (4-3/4 ” ) in radius . F or cutting circles between 121 mm (4-3/4 ” ) and 221 mm (8-11/16 ” ) in radius . NO TE: Circles between 172 mm (6-3/4 ” ) and 186 mm (7-5/16 ” ) in radius cannot be cut using this guide.
12 T rimmer guide T rimming, cur ved cuts in v eneers f or furniture and the like can be done easily with the trimmer guide. The guide roller rides the cur ve and assures a fine cut. Install the trimmer guide on the tool base with the clamp screw (A).
13 Replacing carbon brushes Remov e and check the carbon brushes regularl y . Replace when they w ear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only iden- tical carbon brushes.
Memo 14.
Memo 15.
Memo 16.
17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut.
18 1. This product was pur chased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom F riend Previous Usage Other ( ) 2.
19 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ALABAMA 2365 Pelham P arkway Pelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadw ay Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd.
W ARNING Some dust created by po wer sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm.
An important point after buying a device Makita 3707FC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 3707FC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 3707FC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 3707FC you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 3707FC will certainly help you make a decision on the purchase.
If you already are a holder of Makita 3707FC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 3707FC.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 3707FC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 3707FC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
