Instruction/ maintenance manual of the product ODSHR42 Majestic Appliances
Go to page of 22
ODSHR Series Outdoor W oodbur ning Fireplace Homeowner's Installation & Operating Manual DO NOT DISCARD THIS MANUAL: Retain for future use. 20002264 2/03 Rev .
2 ODSHR Series 20002264 Safety Infor mation PLEASE READ THIS MANUAL BEFORE INST ALLING AND USING FIREPLACE. IMPORT ANT : Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty .
3 ODSH R Series 20002264 Rough Opening Height 42" 52 ¹⁄₄ " 44" ³⁄₄ " ³⁄₄ " 24 " 7⁷⁄₁₆ " 13 ³⁄₈ " Dia.
4 ODSHR Series 20002264 NOTE: If the fireplace is a freestanding unit, it must be located a minimum of 10' from the opening of the firebox to a combustible structure. A minimum height of 6'- 4" measured from the base of the firebox to the bottom of the termination cap is permitted.
5 ODSH R Series 20002264 Chimney Requirements - Offset Installations 0000 0 3 " 1 1 " 1000 0 8 ¹⁄₄ " 20" 0100 0 1 1 ¹⁄₄ "2 5 ¹⁄₄ " 2000 0 1 3 ¹⁄₂ &quo.
6 ODSHR Series 20002264 Planning Infor mation The T en Foot Rule Major U.S. building codes specify a minimum chimney height above the roof top. The “T en Foot Rule” is a fire safety rule and not a draft rule.
7 ODSH R Series 20002264 Chimney Supports The chimney system is supported by the fireplace for vertical chimney heights less than 30 feet above the hearth. Chimney supports are required if the vertical height exceeds 30 feet with 1 1CF chimneys. Locate chimney supports at ceiling holes or other structural framing at 30 foot heights.
8 ODSHR Series 20002264 Locate center point of the chimney on ceiling as though a straight up chimney arrangement is to be used. Measure your offset dimension from straight up chim- ney center point on ceiling.
9 ODSH R Series 20002264 Cutting the Hole Cover fireplace collar opening and cut proper sized chimney hole in chimney . (Fig. 10 & 1 1) Framing the Ceiling Hole Frame the ceiling chimney hole as shown in Figure 1 1. It is good practice to use framing lumber that is the same size as the ceiling joists; this is a requirement at attic level.
10 ODSHR Series 20002264 4. Positioning, Safety Strips, Securing the Fireplace Slide fireplace into position. Lift the fireplace front slightly and slide the metal safety strips under front bottom edge about 1 ¹⁄₂ inches, allowing the remainder to extend in front of firebox.
11 ODSH R Series 20002264 5. Installing the Chimney System Start by attaching the first chimney section to the collar on top of the fireplace. Install the pipe as pictured in Figure 14. When you get a good lock, you will hear the pipe clearly snap to- gether .
12 ODSHR Series 20002264 Firestop spacers are not available for , nor are they required on, vertical walls. The Majestic Fireplaces' chimney components have been tested and approved with the area where the outer pipe slides through the firestop spacer sealed with a noncombustible caulk if desired, or left com- pletely open with no sealant.
13 ODSH R Series 20002264 7. Finish W all Finish the wall with material of your choice. Do not install a combustible mantel shelf less than 12 inches above the front opening. If a combustible material is used below a flat mantel shelf, consult your local building codes for minimum clearance from top of fireplace opening to bottom of mantel shelf.
14 ODSHR Series 20002264 Stud 2 x 4 Finished Header Covered W all Ledge Bracket Finished W all Noncombustible Decorative Facing Must be Sealed with Noncombustible Material Surround FP1 167 Fig. 20 Facing on fireplace surround flush with finished wall.
15 ODSH R Series 20002264 8. Hearth Installation A hearth extension is required to protect a combustible floor in front of the fireplace. See Figure 24 for mini- mum dimensions and mounting detail. NOTE: Hearth Extension must not cover the air inlet opening of a fireplace.
16 ODSHR Series 20002264 COMMON MA TERIALS AND F A CT ORS MA TERIAL K* R MINIMUM THICKNESS EH2416 Common Brick 0.458 5.0 1.09 0.50 in.** 0.10 5.46 in.** (Majestic Products Company) R V alue is for ¹⁄₂ inch. * Units of K = BTU/SQ FT/HR/˚F/IN ** Thickness of Listed Material FP533ADD Fig.
17 ODSH R Series 20002264 From inside the fireplace, locate the knockout on the firebrick -- be sure you are on the appropriate or "gas line" side of the fireplace. Using a flat bladed screw- driver or small chisel and hammer , carefully tap around the knockout until it loosens and falls out.
18 ODSHR Series 20002264 2264 *T wo (2) required ** Four (4) required V ermont Castings, Majestic Products reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice.
19 ODSH R Series 20002264 The following accessories for this appliance are available from your local V ermont Castings, Majestic Products products distributor . Should you need additional information beyond what your distributor can furnish, contact: V ermont Castings, Majestic Products, 410 Admiral Blvd.
20 ODSHR Series 20002264 Accessory Description Model No. Extended Round T op Chimney Sections Chimney Elbows T op Housing with Upper Baffle Chimney Reducer Kit For use with Majestic T ype "1 1CF" Chim- ney Systems. Used to terminate chimney at top of chase.
21 ODSH R Series 20002264 LIMITED W ARRANTY & 30 YEAR PROTECTION PLAN For V er mont Castings, Majestic Products PRE-ENGINEERED Fireplace Systems V ermont Castings, Majestic Products warrants its P.
22 ODSHR Series 20002264 © V ermont Castings, Majestic Products 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777 www .majesticproducts.
An important point after buying a device Majestic Appliances ODSHR42 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Majestic Appliances ODSHR42 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Majestic Appliances ODSHR42 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Majestic Appliances ODSHR42 you will learn all the available features of the product, as well as information on its operation. The information that you get Majestic Appliances ODSHR42 will certainly help you make a decision on the purchase.
If you already are a holder of Majestic Appliances ODSHR42, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Majestic Appliances ODSHR42.
However, one of the most important roles played by the user manual is to help in solving problems with Majestic Appliances ODSHR42. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Majestic Appliances ODSHR42 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center