Instruction/ maintenance manual of the product CC13B1MG Magnavox
Go to page of 60
TV CR CC13B1MG CC19B1MG Color TV with built-in VCR Color TV with built-in VCR Owner’s Manual Owner’s Manual.
Once your purchase is registered, you’re eligible to receive all the privileges of owning this prod- uct. So complete and return the Warranty Registration Card enclosed with your purchase at once.
Introduction 3 • Before doing anything else, record the TV/VCR’s model and serial num- bers in the spaces provided on page two. These numbers will help us assist you if you ever call for help. • Your new product, its packaging, and this manual contain materials that can be recycled and reused.
4 Table of Contents Setting Up Your TV/VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• The remote control and its batteries are supplied. • Do not mix alkaline and man- ganese batteries. • Do not mix old and new batteries. Before Using the TV/VCR 5 Putting Batteries in the Remote Control 1 Remove the battery compartment lid on the bottom of the remote control by sliding it in the direction of the arrow.
6 Hooking Up the TV/VCR ANT. ANT. Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna ANT. IN OUT ANT. Connect an RF coaxial cable (75- ohm, not supplied) to the OUT Jack on the Cable Box and to the ANT(enna) Jack on the TV/VCR. Connect a Cable signal or an antenna to the ANT(enna) Jack.
Hooking Up the TV/VCR (cont’d) 7 AUDIO VIDEO STOP EJECT REW PLAY F.FWD REC OTR CHANNEL VOLUME POWER EARPHONE OUT IN VIDEO IN OUT 3CH 4CH AUDIO ANT. OUT IN VIDEO IN OUT 3CH 4CH AUDIO ANT. VIDEO AUDIO • Before connecting an antenna or cable signal to the ANT(enna) Jack, make sure the pin is not bent.
8 Turning On the TV/VCR Before you turn on the TV/VCR, make sure batteries are in the remote control and the TV/VCR is hooked up correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. 1 Press the POWER button.
Language Selection 9 Follow the steps below to change the language of the on-screen displays and menus. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to choose SELECT LANGUAGE. Then, press the FF/SEARCH/ B button. 4 Press the PLAY/ ▲ button or the STOP/ ▼ button to select ENGLISH or ESPAÑOL (Spanish).
10 Automatic Channel Setup Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following the steps below. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select PRIM.
Automatic Channel Setup (cont’d) 11 4 Press the FF/SEARCH/ B button or the REW(ind)/SEARCH/ { button to select SAVED (to add that channel) or DELETED (to delete that channel). Repeat steps 3-4 to add or delete other channels. 5 Press the STATUS/EXIT button.
12 Setting the Clock • Entries that do not match the TV/VCR’s clock or calendar will cause a question mark (?) to appear on the screen. • To make corrections while you are setting the clock, press the CLEAR button until the space for the informa- tion you want to correct is flashing.
Setting the Clock (cont’d) 13 5 Press two Number buttons for the hour(s) and two Number buttons for the minute(s). Then press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
14 Setting the Clock (cont’d) Automatic PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the PLAY/ ▲ button or the STOP/ ▼ button to select AUTO CLOCK. Then, press the FF/SEARCH/ B button so that ON appears to the right of AUTO CLOCK, then press the MENU button.
Setting the Clock (cont’d) 15 7 When the TV/VCR finds the PBS channel, the time will appear on the screen. Press the STATUS/EXIT button. 6 NOW SEARCHING flashes on the TV/VCR screen. ● If CANNOT FIND CLOCK DATA flashes on the TV/VCR screen, you will be prompted to turn off the TV/VCR.
16 Setting the Clock (cont’d) Manual PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the PLAY/ ▲ button or the STOP/ ▼ button to select AUTO CLOCK. Then, press the FF/SEARCH/ B button so that ON appears to the right of AUTO CLOCK, then press the MENU button.
Setting the Clock (cont’d) 17 8 When the TV/VCR finds the clock data, the time will appear on the screen. Press the STATUS/EXIT button. 6 Use the Number buttons to select your PBS station.
18 Daylight-Savings Time 4 Press the PLAY/ ▲ button or the STOP/ ▼ button to select DAYLIGHT SVG.TIME. Then, press the FF/SEARCH/ B button so that ON or OFF appears beside DAYLIGHT SVG. TIME (Daylight Savings Time). 5 Press the STATUS/EXIT button.
Time Zone 19 When you set the clock using AUTO CLOCK, specify your time zone. The TV/VCR will maintain the clock according to your time zone. • If you select AUTO at step 5, the TV/VCR will set the clock according to the time zone data of the PBS station it finds.
20 Front Panel AUDIO VIDEO STOP EJECT REW PLAY F.FWD REC OTR CHANNEL VOLUME POWER EARPHONE Cassette Compartment Insert a video cassette tape here. POWER Button Press to turn the power on or off.
Rear Panel 21 ANT . ANT(enna) Jack Connect your antenna or cable here. Details are on pages six-seven. Antenna Hole Connect the stem of an indoor antenna here. Details are on page six. AC Power Cord Connect to a standard AC outlet to supply power to the TV/VCR.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY MENU Button Press to display the pop up menu. You also may use the buttons on the front panel of the TV/VCR to access the pop up menu.
REW(ind)/SEARCH/ { Button When tape playback is stopped, press to rewind the tape at high speed. During tape playback, press to rewind the tape while the picture stays on the screen. Details are on page 41. Press to change a setting of a pop up menu item or to return to a previous menu.
TO ADJUST PRESS { / B 24 Adjusting the Picture Controls Follow these steps to adjust the TV/VCR’s brightness, picture, color, tint, and sharpness. 1 Press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select the desired control (BRIGHTNESS, for example).
Adjusting the Picture Controls (cont’d) 25 Decrease Increase BRIGHTNESS decreased brightness increased brightness PICTURE decreased contrast increased contrast COLOR paler more brilliant TINT more purple more green SHARPNESS softer clearer Press the REW(ind)/SEARCH/ { button to decrease a picture control.
• You cannot view closed captions during recording or tape playback if COUNTER ONLY is set to ON. Details are on pages 48-49. • If STATUS is set to ON, closed cap- tions will be interrupted briefly when you insert or remove a tape. Details are on page 48-49.
Reminder 27 The channel number will remain on the screen at all times when you set REMINDER to ON. The exceptions are during tape play- back or when closed captioning is selected. Set REMINDER to ON or OFF by following the steps below. 1 Press the MENU button.
28 Playing • If the tape you want to play is already in the TV/VCR, turn on the TV/VCR power, then press the PLAY/ ▲ button. • Playback features and options are on pages 37-41. • When you play a tape recorded in S-VHS format on this unit, you can not get the high resolution that would be available on an S-VHS VCR.
Recording 29 • You cannot record one channel while watching another. • Recording options are on pages 30-36. • You cannot record if DEFEAT RECORDING is set to ON.
30 One-Touch Recording The One-Touch Recording (OTR) function allows you to program an immediate timed recording from 30 minutes to eight hours long without setting the timer. Before you begin, make sure: ● Channels are set up. ● There is a tape in the TV/VCR.
Rerecording (Tape Duplication) 31 • Unauthorized recording of copy- righted television programs, video tapes, or other materials may infringe on the rights of copyright owners and violate copyright laws. • If a program has copyright protec- tion, it may not record clearly.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY 32 Timer Recording Follow the steps below to program the TV/VCR to record TV programs while you’re away from home.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY ONE TIME PROGRAM PROGRAM 1 CHANNEL – – .
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY 34 Timer Recording (cont’d) Turn off the TV/VCR for the recording. Insert a tape in the TV/VCR.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY Timer Recording (cont’d) 35 6 Repeat steps 1 - 4 to make sure you have cleared the cor- rect position.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY 36 Defeat Recording Follow the steps below to prevent accidental recording. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR SETUP, then press the FF/SEARCH/ B button.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY Repeat Play 37 Follow the steps below to program the TV/VCR to play a tape over and over.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY 38 A-B Repeat Play • To cancel A-B Repeat Play, set ONE TIME PLAY to ON. To set ONE TIME PLAY to ON, follow steps 2-3 above.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY 6 Press the STATUS/EXIT button to remove the menu. A-B REPEAT will appear on the screen. Beneath it, the letter A will flash beside the real-time counter.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY 40 Real-Time Counter Memory Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later.
Playback Options 41 Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the FF/SEARCH/ B button or the REW(ind)/SEARCH/ { button. A fast forward or reverse picture search will begin. 2 To return to normal playback, press the PLAY/ ▲ button.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY 42 SmartLock SmartLock enables parents to prevent their children from watch- ing inappropriate material on TV.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY SmartLock (cont’d) 43 5 Press the PLAY/ ▲ button or the STOP/ ▼ button to select Movie Ratings or Parental Guidelines.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY To change the access code, follow these steps. 44 SmartLock (cont’d) 1 Press the MENU button.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY SmartLock (cont’d) 45 To check the SmartLock settings, follow these steps. 1 Press the MENU button.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY 46 Wake Up Timer 1 4 2-3 The Wake Up Timer turns on the TV/VCR automatically at a speci- fied time within the next 24 hours.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY 1 Press the SLEEP/WAKE UP button. • To cancel the Sleep Timer, press the SLEEP/WAKE UP button.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY When you watch a program that is being broad.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY Closed Caption (cont’d) 49 • You cannot view closed captions dur- ing recording or tape playback if COUNTER ONLY is set to ON.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY 2 Press the PLAY/ o o button or the STOP/ p p button to select VCR SETUP, then press the FF/SEARCH/ B B button.
POWER CLEAR STATUS/EXIT 1 2 3 4 5 6 7 8 9 0 CHANNEL SLEEP/WAKE UP MUTE SPEED VOLUME REW/SEARCH PLAY/ FF/SEARCH REC/OTR PAUSE/STILL STOP/ ALT.CH MENU MEMORY Usually, the volume bar appears when you press the VOLUME ▲ / ▼ buttons. If you do not need it, set the VOLUME BAR to OFF.
52 Automatic Operation Features The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically.
General CRT: 13-inch in line gun (CC13B1MG) 19-inch in line gun (CC19B1MG) Television system: NTSC-M Closed caption system: Section 15.119, FCC (Federal Communications Commission) Standard Video Heads: Two heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.
54 Helpful Hints Location For safe operation and satisfactory performance of your TV/VCR, remember the following: • Shield it from direct sunlight and keep it away from sources of intense heat. • Avoid dusty or humid places. • Avoid places with insufficient ventilation.
Helpful Hints (cont’d) 55 The remote control is not available, or the remote control will not access the pop up menu. • Use the buttons on the front panel of the TV/VCR to access the pop up menu. You can not enter numbers (for example, to program a timer recording) using the front panel buttons.
AUDIO In Jack: jack located on the front of the TV/VCR which is used to record audio from another source. Automatic Channel Setup: process in which the TV/VCR scans all available channels and places the ones you receive in its memory. Then, when you push the CHANNEL o / p buttons, you only scan through channels you receive.
RENEWED 90 DAY LIMITED WARRANTY.
a-b repeat play . . . . . . . . .38-39 accessories . . . . . . . . . . . . . . .60 ant(enna) jack . . . . . . . . . . .6, 21 audio in jack . . . . . . . . .7, 20, 31 automatic playback . . . . . . . . . . . . . . .52 rewind . . . . . . . . . . . . . .
.
IB8204E001 Printed In Malaysia 0EMN01666 / T5114UQ * * * * * S UPPLIED A CCESSORIES O PTIONAL A CCESSORIES The following items are supplied with your TV/VCR; they are provided to help you use or set up your TV/VCR. The following additional items are not provided with your TV/VCR, but they are designed for use with your new TV/VCR.
An important point after buying a device Magnavox CC13B1MG (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Magnavox CC13B1MG yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Magnavox CC13B1MG - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Magnavox CC13B1MG you will learn all the available features of the product, as well as information on its operation. The information that you get Magnavox CC13B1MG will certainly help you make a decision on the purchase.
If you already are a holder of Magnavox CC13B1MG, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Magnavox CC13B1MG.
However, one of the most important roles played by the user manual is to help in solving problems with Magnavox CC13B1MG. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Magnavox CC13B1MG along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
