Instruction/ maintenance manual of the product PPC-200 Magnadyne
Go to page of 8
Owner's Man ual Model PPC-200 AM/FM Stereo Receiver with Digital Clock, Seek / Scan / Manual T uning ME RCL 12 3 45 6 TUNING FM/ AM LO/ DX SEEK SCAN TONE VOLUME ON/OFF M H FADER TIME ST FM LOC CH.
CONTROLS AND OPERA TIONS On / Off / V olume / Balance / Control Knob (1) T o turn the unit on, rotate the the volume control knob to the right. T o adjust the the volume level, continue rotating the knob to the right. T o turn the unit off, rotate the knob to the left until it clicks.
CONTROLS AND OPERA TIONS Seek/ Scan Button (6) Pressing the seek button will cause the tuner to search out the next strongest station up the tuning scale. T o continue seeking, you must repeatedly press the seek button each time the tuner stops on a station.
CONTROLS AND OPERA TIONS How to Preset Radio Stations: Repeat the following procedures to memorize radio stations: 1. T urn on the unit by rotating the volume control knob to the right. 2. Select the radio band (FM1, FM2, AM1) you want to memorize radio stations in by pressing the FM/AM button.
INST ALLING THE RADIO Installing the Radio 1. Locate the factory supplied opening for the radio or choose a location within reach of the primary operator of the vehicle. 2. Cut and file the opening if necessary so the shafts and the nosepiece of the radio will slide through the opening.
ELECTRICAL CONNECTIONS 6 RED (+) To 12 Volt DC Power ORANGE Memory to Battery BLACK ( - ) To Ground YELLOW Power Antenna GREEN (+) ORANGE ( - )* LEFT REAR Noise Filter BLUE (+) WHITE ( - )* GRAY (.
ELECTRICAL CONNECTIONS Red Wire: (with fuse holder and noise filter) Connect the red wire to a +12 volt power source that is “switched on and off by the ignition key . Most power sources can be located at the vehicles fuse block. Use a test light or volt meter to select the correct connection point.
SPECIFICA TIONS FM T uner Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5 - 107.9MHz Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . 17dBf (2uV) 50dB Quieting Sensitivity . . . . . . . . . . . . . .
An important point after buying a device Magnadyne PPC-200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Magnadyne PPC-200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Magnadyne PPC-200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Magnadyne PPC-200 you will learn all the available features of the product, as well as information on its operation. The information that you get Magnadyne PPC-200 will certainly help you make a decision on the purchase.
If you already are a holder of Magnadyne PPC-200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Magnadyne PPC-200.
However, one of the most important roles played by the user manual is to help in solving problems with Magnadyne PPC-200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Magnadyne PPC-200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
