EN
LOREX Technology logo
Official user manual

LOREX Technology DGN209

52 pages·3.1 MB·DVR·PDF·ENDEFRITNLJA
LOREX Technology DGN209
Table of Contents 79 sections Important Safety Instructions · Introduction · Features · System Contents · … ShowHide
Important Safety Instructionsp.5Introductionp.6Featuresp.6System Contentsp.7Getting Startedp.7Front Panel Controlsp.82. LED INDICATORSp.814. PAUSE / Upp.8Back Panel Connectionsp.10Accessing the Main Menup.11Main Menup.11Searchp.11Last Recordp.12Full Listp.12Alarm Listp.12Motion Listp.12Time Searchp.12Timer Recording Setupp.12Timerp.13Record Settingsp.14HDD Overwrite Setupp.14Record IPS Setupp.14Record Quality Setupp.14Alarm REC IPS Setupp.14Alarm REC Quality Setupp.14Motion Trigger Recordp.15Camera Channel Setupp.15Motion Detectionp.17System Setupp.19Selecting the Audio Input Channelp.19Setting the Internal Audible Alarm Buzzerp.19Setting the External Audible Alarm Devicep.19Setting the Motion Audible Alarm featurep.20Setting the Alarm Durationp.20Setting the Dwell Timep.20Setting the Message Latch Featurep.20System Time/Date Set upp.20Selecting the Date Display Formatp.20Setting System Time & Datep.21Changing the System Passwordp.21Clearing the Hard Drive Datap.21Resetting System to Factory Defaultsp.21Networkp.22Operationp.22On Screen Display (OSD)p.22Video Loss - Screen will display if the video input is not connected properly.p.23Recording Methodsp.23Viewing Options:p.23Individual Camera Select (1 - 9):p.23Multi View Select:p.23Picture in Picture (PIP):p.23Zoom:p.23Video Searchp.24Playing Back Videop.24Hardware Connection from DVRp.25Static IP Settingp.25STEP 2: STATIC IP SETTINGp.27Dynamic IP Settingp.28WHAT IS A DYNAMIC IP ADDRESS?p.28STEP 2: DDNS REGISTRATION FOR A DYNAMIC IP ADDRESS:p.28STEP 5 : IP SETTINGp.33STEP 6 : Connect Routerp.33STEP 7 : Connect to the DVR via the Internetp.34Software Operation at the Remote Sitep.35Control Panel and Basic Operationp.36A. Video Web Server control panelp.36B. Digital device control panelp.37Play Back Operationp.37Advanced Settingsp.38Connecting the Video Web Server Via the Internet Explorer Browserp.40Key Lockp.42Troubleshootingp.43Technical Specificationsp.44Appendix 1: Installing the HDDp.45Appendix 2: Connection Diagram to Cameras and Monitorp.47Appendix 3: Pin Configurationsp.48Appendix 4: Rack Mount Installationp.49Appendix 5: Recording Times (in Hours)p.50Appendix 6: Compatible HDD Brandsp.51
Page 1 of the LOREX Technology DGN209 user manual — MODEL: DGN209
Page 1 · click to enlarge
Page 1

9 CHANNEL MULTIPLEX DIGITAL VIDEO RECORDER

Instruction Manual

English Version1.0

LOREX Technology DGN209 — 9 CHANNEL MULTIPLEX DIGITAL VIDEO RECORDER diagram (page 1)
Fig. 1

MODEL: DGN209

www.lorexcctv.com

Copyright © 2006 LOREX Technology Inc.

Page 2 of the LOREX Technology DGN209 user manual
Page 2 · click to enlarge
Page 2

Under the copyright laws, this documentation may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or part without the prior written consent of Lorex Technologies Inc., except in the manner described in the documentation.

Lorex Technologies Inc.

300 Alden Road Markham, Ontario L3R 4C1 CANADA

All rights reserved. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at one’s own expense. CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

1. THIS DEVICE MAY NOT CAUSE HARMFULL INTERFERENCE, AND 2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

© Copyright 2006

Page 3 of the LOREX Technology DGN209 user manual — Table of contents
Page 3 · click to enlarge
Page 3

Table of contents

Important Safety Instructionsp.5Introductionp.6Featuresp.6System Contentsp.7Getting Startedp.7Front Panel Controlsp.82. LED INDICATORSp.814. PAUSE / Upp.8Back Panel Connectionsp.10Accessing the Main Menup.11Main Menup.11Searchp.11Last Recordp.12Full Listp.12Alarm Listp.12Motion Listp.12Time Searchp.12Timer Recording Setupp.12Timerp.13Record Settingsp.14HDD Overwrite Setupp.14Record IPS Setupp.14Record Quality Setupp.14Alarm REC IPS Setupp.14Alarm REC Quality Setupp.14Motion Trigger Recordp.15Camera Channel Setupp.15Motion Detectionp.17System Setupp.19Selecting the Audio Input Channelp.19Setting the Internal Audible Alarm Buzzerp.19Setting the External Audible Alarm Devicep.19Setting the Motion Audible Alarm featurep.20Setting the Alarm Durationp.20Setting the Dwell Timep.20Setting the Message Latch Featurep.20System Time/Date Set upp.20Selecting the Date Display Formatp.20Setting System Time & Datep.21Changing the System Passwordp.21Clearing the Hard Drive Datap.21Resetting System to Factory Defaultsp.21Networkp.22Operationp.22On Screen Display (OSD)p.22Video Loss - Screen will display if the video input is not connected properly.p.23Recording Methodsp.23Viewing Options:p.23Individual Camera Select (1 - 9):p.23Multi View Select:p.23Picture in Picture (PIP):p.23Zoom:p.23Video Searchp.24Playing Back Videop.24Hardware Connection from DVRp.25Static IP Settingp.25STEP 2: STATIC IP SETTINGp.27Dynamic IP Settingp.28WHAT IS A DYNAMIC IP ADDRESS?p.28STEP 2: DDNS REGISTRATION FOR A DYNAMIC IP ADDRESS:p.28STEP 5 : IP SETTINGp.33STEP 6 : Connect Routerp.33STEP 7 : Connect to the DVR via the Internetp.34Software Operation at the Remote Sitep.35Control Panel and Basic Operationp.36A. Video Web Server control panelp.36B. Digital device control panelp.37Play Back Operationp.37Advanced Settingsp.38Connecting the Video Web Server Via the Internet Explorer Browserp.40Key Lockp.42Troubleshootingp.43Technical Specificationsp.44Appendix 1: Installing the HDDp.45Appendix 2: Connection Diagram to Cameras and Monitorp.47Appendix 3: Pin Configurationsp.48Appendix 4: Rack Mount Installationp.49Appendix 5: Recording Times (in Hours)p.50Appendix 6: Compatible HDD Brandsp.51
Page 4 of the LOREX Technology DGN209 user manual — Table of contents
Page 4 · click to enlarge
Page 4

Table of contents

Important Safety Instructionsp.5Introductionp.6Featuresp.6System Contentsp.7Getting Startedp.7Front Panel Controlsp.82. LED INDICATORSp.814. PAUSE / Upp.8Back Panel Connectionsp.10Accessing the Main Menup.11Main Menup.11Searchp.11Last Recordp.12Full Listp.12Alarm Listp.12Motion Listp.12Time Searchp.12Timer Recording Setupp.12Timerp.13Record Settingsp.14HDD Overwrite Setupp.14Record IPS Setupp.14Record Quality Setupp.14Alarm REC IPS Setupp.14Alarm REC Quality Setupp.14Motion Trigger Recordp.15Camera Channel Setupp.15Motion Detectionp.17System Setupp.19Selecting the Audio Input Channelp.19Setting the Internal Audible Alarm Buzzerp.19Setting the External Audible Alarm Devicep.19Setting the Motion Audible Alarm featurep.20Setting the Alarm Durationp.20Setting the Dwell Timep.20Setting the Message Latch Featurep.20System Time/Date Set upp.20Selecting the Date Display Formatp.20Setting System Time & Datep.21Changing the System Passwordp.21Clearing the Hard Drive Datap.21Resetting System to Factory Defaultsp.21Networkp.22Operationp.22On Screen Display (OSD)p.22Video Loss - Screen will display if the video input is not connected properly.p.23Recording Methodsp.23Viewing Options:p.23Individual Camera Select (1 - 9):p.23Multi View Select:p.23Picture in Picture (PIP):p.23Zoom:p.23Video Searchp.24Playing Back Videop.24Hardware Connection from DVRp.25Static IP Settingp.25STEP 2: STATIC IP SETTINGp.27Dynamic IP Settingp.28WHAT IS A DYNAMIC IP ADDRESS?p.28STEP 2: DDNS REGISTRATION FOR A DYNAMIC IP ADDRESS:p.28STEP 5 : IP SETTINGp.33STEP 6 : Connect Routerp.33STEP 7 : Connect to the DVR via the Internetp.34Software Operation at the Remote Sitep.35Control Panel and Basic Operationp.36A. Video Web Server control panelp.36B. Digital device control panelp.37Play Back Operationp.37Advanced Settingsp.38Connecting the Video Web Server Via the Internet Explorer Browserp.40Key Lockp.42Troubleshootingp.43Technical Specificationsp.44Appendix 1: Installing the HDDp.45Appendix 2: Connection Diagram to Cameras and Monitorp.47Appendix 3: Pin Configurationsp.48Appendix 4: Rack Mount Installationp.49Appendix 5: Recording Times (in Hours)p.50Appendix 6: Compatible HDD Brandsp.51
Page 5 of the LOREX Technology DGN209 user manual — CAUTION
Page 5 · click to enlarge
Page 5

Important Safety Instructions

All the safety and operating instructions should be read before operating this equipment. The improper operation may cause irreparable damage to the appliance. Lift and place this equipment gently. Do not expose this equipment to direct sunlight. Do not use this equipment near water or in contact with water. Do not spill liquid of any kind on the equipment. Do not unplug the power connector before turning the power off correctly. This equipment should be operated using only the power source from standard package. Unauthorized repair or parts substitutions may result in fire, electric shock or other hazards. Do not switch the Power On & Off within short period (within 3 seconds). Do not attempt to service this equipment by yourself. Refer all servicing to qualified service personnel. This installation should conform to all local codes. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-

CAUTION

!

RISK OF ELECTRIC SHOCK. DO NOT OPEN.

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Page 6 of the LOREX Technology DGN209 user manual — Introduction
Page 6 · click to enlarge
Page 6

Introduction

The DXR209 combines a 9 channel multiplexer with a Digital Video Recorder (DVR). The DVR offers many advantages over traditional time lapse VCR’s, allowing you to quickly access and search for a specific time segment or event, which has been recorded. This high quality recorded video can be viewed at various playback speeds as well as frame-by-frame with the Jog Button feature. To learn more about Lorex products, please visit our website at www.Lorexcctv.com Features

  • Wavelet Compression Format
  • 4 Audio inputs and 2 outputs
  • Resolution: 704X564 - full screen, 352X282 - 4 channels, 224X188 9 - channels
  • Independent main and call monitor outputs allow for sequencing of camera views or full screen viewing
  • Multi screen display mode
  • 9 channel alarm input, alarm display and 1 alarm output
  • Video loss detection able to record 160 events on each channel
  • Power-loss memory feature (In case of power failure, set-up parameter will remain)
  • Supports 1 removable HDD, IDE type (up to a maximum of 250GB)
  • Display refresh rate up to 72 IPS (NTSC) and 50 IPS(PAL)
  • Record refresh rate up to 25 IPS (NTSC) and 22 IPS (PAL)
  • Quick multiple search by date/time, alarm or full list
  • Multiple speed playback
  • Security password protection
  • LAN connector for internet connection
Page 7 of the LOREX Technology DGN209 user manual — DISK DRIVE. Getting Started
Page 7 · click to enlarge
Page 7

System Contents

The DXR209 box should include the items listed below. Please take a moment to verify that no items are missing from the package. NOTE: KEEP THE KEYS IN A SAFE PLACE. THEY ARE NECESSARY FOR INSTALLATION / REMOVAL OF THE HARD

LOREX Technology DGN209 — System Contents diagram (page 7)
Fig. 2 · System Contents
LOREX Technology DGN209 — System Contents diagram (page 7)
Fig. 3 · System Contents

DXR209 Digital Video Recorder 80 GB Hard Disk Drive is included

LOREX Technology DGN209 — System Contents diagram (page 7)
Fig. 4 · System Contents
LOREX Technology DGN209 — System Contents diagram (page 7)
Fig. 5 · System Contents
LOREX Technology DGN209 — System Contents diagram (page 7)
Fig. 6 · System Contents

Installation / User Manual Power Adapter and Cord 2 Keys for Hard Drive Cartridge

DISK DRIVE. Getting Started

If the purchased DVR model did not contain a hard disk drive, please refer to Appendix #1 for HDD installation instructions.

1. Connect video sources and monitor(s) following the configuration example shown in Appendix # 2 . 2. Connect the AC Power Cord to the Power Adapter and plug into an electrical outlet. A Red LED indicator light will be ON to indicate that the DVR is in Standby mode.

3. Press the Power button. The POWER LED will turn from red to orange, and other red LED indicators will turn ON. Note: the system takes approximately 5 to 15 seconds to power up. During the power-up, you will see the following messages: “HDD Detecting”, followed by “Master HDD Connected”. Once connected, the POWER LED will change to green, and the red indicator lights will be ON next to the Alarm and Timer buttons. (The Alarm and Timer LED’s simply indicate that these features are enabled) NOTE: IF YOU GET THE MESSAGE “HDD NOT FOUND”, PLEASE SEE APPENDIX #1 AS THE HDD IS LIKELY NOT

INSTALLED CORRECTLY.

Page 8 of the LOREX Technology DGN209 user manual — 1 3 6 4 7 8 9 2 5 10 11 12
Page 8 · click to enlarge
Page 8
LOREX Technology DGN209 — Front Panel Controls diagram (page 8)
Fig. 7 · Front Panel Controls
  • 1. REMOVABLE HDD CARTRIDGE Please refer to Appendix #1. 2. LED INDICATORS These LED Lights are ON under the following conditions:
  • HDD Full: HDD is full
  • ALARM: If you want to turn off the ALARM LED light, please refer to page 13 and set the Camera / ALARM item as OFF (all of the cameras should be set as OFF.)
  • TIMER: When Timer is set as Enabled
  • PLAY: On Play mode
  • REC: On Recording mode 3. MENU Press MENU to enter or exit the system setup menu. 4. ENTER Press ENTER to select an item for change while in the setup menu. 5. SELECT Press the SELECT button to change the camera shown in the individual panes of the multi screen modes. 6. ZOOM Press ZOOM to enlarge the picture display 2x. 7. This button has two functions: PIP & Motion Detection (a) Press the PIP button to change to Picture in Picture mode. (b) When you are in the Camera Channel Setup Menu and Motion Detection is activated it turns all targets on the screen ON or OFF. 8. 4/7 channel display mode 9. 9 channel display mode 10. REC Press REC to start recording. 11. STOP / Down
  • STOP: Under the DVR Record / Play mode, it can stop the moment action.
  • DOWN: When in the setup mode, it works as the Down directional button. 12. POWER Press Power to turn ON / OFF the DVR. 13. FF / Right FF: It can play video forward at high speed, and press FF again to adjust speed from 1, 2, 4, 8, 16, 32 times. Right: When in the setup mode, it can work as the Right directional button. 14. PAUSE / Up Pause: Under the DVR play mode, it can pause the action.

1 3 6 4 7 8 9 2 5 10 11 12

1 3 6 4 7 8 9 2 5 10 11 12

Page 9 of the LOREX Technology DGN209 user manual — Front Panel Controls
Page 9 · click to enlarge
Page 9

UP: When in the setup mode, it works as an Up directional button. 15. PLAY Press PLAY to playback the most recently recorded video. 16. REW / Left REW: Under DVR play mode, it can play video backward at different speeds. (Press REW again to adjust speed as 1, 2, 4, 8, 16, 32 times) Left: When in the setup mode, it works as Left directional button. 17. SLOW Press to slow down the playback speed. 18. CAMERA SELECT (1-9) Press the Camera Select (1-9) to select specified camera.

Page 10 of the LOREX Technology DGN209 user manual — Back Panel Connections
Page 10 · click to enlarge
Page 10

Back Panel Connections

1. POWER INPUT Connects to the Power cord. 2. EXTERNAL I/O Connects to a PC for Remote Control via RS-232 or to an Alarm Block. (see Appendix #3 for more info) 3. 75/HI When using the LOOP function, allows for HI impedance or 75ohms. 4. VIDEO INPUT (1-9) Connects to a video source (i.e. camera). 5. CALL Connects to the CALL monitor for real time sequencing. 6. LAN Connects DVR by LAN cable. 7. AUDIO OUTPUT (R/L) Connects to monitor or speaker (2 mono audio outputs from the same source) 8. AUDIO INPUT (1-4) Connects to an audio source such as a microphone for recording purposes (4 audio inputs, but only 1 can be selected during recording). 9. MAIN Connects to the main display monitor. 10. LOOP (1-9) Allows connection to other video devices.

10 9 8 7

LOREX Technology DGN209 — Back Panel Connections diagram (page 10)
Fig. 8 · Back Panel Connections

1 2 3 4 5 6

Page 11 of the LOREX Technology DGN209 user manual — Accessing the Main Menu
Page 11 · click to enlarge
Page 11

Accessing the Main Menu

The Menu allows you to configure your DVR settings and program various recording options. Follow these steps in order to access the Menu:

Press the MENU button. The password screen will appear: The default Password is 0000.

Password0000

To change the number of the Password, use the ◄ / ► buttons to scroll left and right between numbers, and use the ▲ / ▼ buttons to change the value of the number that is flashing. Press the ENTER button once the correct Password is entered. The menu options screen will appear. NOTE: If you get a message “Password Error”, you have entered an incorrect password. Main Menu When the correct password is entered, the Main Menu options will be displayed. There are 7 options available in the Main Menu: Search: Finds recorded list Timer: Scheduling recording Record: Record mode setup Camera: Camera channel setup System: System setup (sets the date, chooses an HDD overwrite setting, changes password, resets system settings, or clears the HDD) Event: Event List - Allows you to view video from a list of recorded events Network: Network setup Navigating the Menu: ▲ / ▼: Scroll up and down through menu options; change values when an option is selected and is blinking ◄ / ►: Scroll sideways within a menu option that has been selected ENTER: Selects a submenu / an option in a submenu for browsing / modification MENU: Completes modification of a menu option; exits a menu NOTE: The Menu setup will timeout after 1 minute of no key presses. Search The DXR209 allows you to easily find sections of recorded video using the SEARCH feature. To access the Search option, press MENU followed by the 4 digit password. Use the ▲ / ▼ to scroll to the Search option and press ENTER.

(Menu) Search Timer Record Camera System Event Network

(Menu) ► Search Timer Record Camera System Event Network

Page 12 of the LOREX Technology DGN209 user manual — Last Record
Page 12 · click to enlarge
Page 12

The following options are available in the Search Menu:

►Last Record Full List Alarm List Motion List Time Search

Last Record

This feature is used to play the last recorded piece of video.

  • In the Search menu, press ▲ / ▼ to scroll to the Last Record option, then press ENTER .
  • The last recorded video will begin playing. Full List

This feature is used to choose from a listing of all recorded video on the HDD sorted by time.

1. In the Search menu, press ▲ / ▼ to scroll to the Full List option, then press ENTER .
2. Press ▲ / ▼ to select the desired recorded video and press ◄ / ► to change pages.
3. Press ENTER to play selected video.

An example of a Full List search is shown on the left. Note that the date and time appear, along with the letter representing the method of recording that took place. Press ENTER to view a selected piece of video on the list. The DXR209 will play the video in chronological order, until it hits the End of the list. Playback can be stopped at any time by pressing the STOP button. D: Motion Recording M: Manual Record Time A: Alarm Record Time T: Timer Recording M-HDD: Storage in Master HDD S-HDD: Storage in Slave HDD Alarm List

► M 2002-JAN-01 01:02:03 M-HDD M 2002-JAN-01 01:02:03 M-HDD A 2002-JAN-01 01:02:03 M-HDD T 2002-JAN-01 01:02:03 M-HDD D 2002-JAN-01 01:02:03 S-HDD M 2002-JAN-01 01:02:03 S-HDD ◄: Page Up ►: Page Down

This feature shows a listing of all recorded video triggered by an Alarm.

1. In the Search menu, press ▲ / ▼ to scroll to the Alarm List option, then press ENTER .
2. Press ▲ / ▼ to select the desired recorded video and press ◄ / ► to change pages.
3. Press ENTER to play selected video. Motion List This feature shows a list of all triggered motion detections.
1. In the Search menu, press ▲ / ▼ to scroll to the Motion List option, then press ENTER .
2. Press ▲ / ▼ to select the desired recorded video and press ◄ / ► to change pages.
3. Press ENTER to play selected video. Time Search

This feature finds video recorded on a specific time and date that is entered.

1. In the Search menu, press ▲ / ▼ to scroll to the Time Search option, then press ENTER .
2. Press ▲ / ▼ to select the desired time and date, and press ◄ / ► to move to the next character.
3. Press ENTER to play selected video. NOTE: If there is no record found that matches the selected time and date, the screen will display “NOT FOUND”.
Page 13 of the LOREX Technology DGN209 user manual — Timer Recording Setup
Page 13 · click to enlarge
Page 13

Timer Recording Setup

On the Main Menu, selecting the Timer option will allow you to set daily schedules in which you would like the DVR to automatically record. Pressing ENTER after scrolling to the Timer option will bring up the following menu options: Timer

System Event Network (Timer) Day Start End QUALITY IPS Daily 01:00 02:00 BEST 25A SUN 12:00 13:00 BEST 15 MON 08:00 09:00 HIGH 10 MO~FR 00:00 01:00 NORMAL 2 SA~SU 20:00 21:00 BASIC 25A JAN-01 15:00 16:00 NORMAL 8 Timer Enable: No

Example: If you want to record from Tuesday at 8 pm (21:00) to Wednesday at 9 am (09:00) you will need to make two separate entries Day Start End TUE 21:00 23:59 WED 24:00 09:00

1. Press ▲ / ▼ to select the day(s) to record on, the available options are: Daily: Everyday SUN: Sunday MON: Monday TUE: Tuesday WED: Wednesday THU: Thursday FRI: Friday SAT: Saturday MO-FR: Monday to Friday SA-SU: Saturday & Sunday JAN-01: Special Date OFF: Not activated 2. Use the ◄ / ► scroll keys to move to START record time 00:00 (HH:MM) Press ▲ / ▼ to set the start time 3. Press ◄ / ► move to END record time 00:00 (HH:MM) Press ▲ / ▼ to change END record Time numerical digit 4. Press ◄ / ► move to QUALITY Press▲ / ▼ to choose options of

BEST, HIGH, NORMAL, BASIC 5. Press ◄ / ► move to Record IPS (Images Per Second) Press▲ / ▼ to choose one of the following options NTSC: 25A, 15, 8, 4, 2, 1 PAL: 18A, 12, 6, 3, 2, 1

7. Press ◄ / ► move location to Timer Enable, Yes or No setup YES : To confirm Timer Enable/Scheduling Timer Record feature NO : To confirm no Timer Enable/No Scheduling Timer Record feature
8. Press MENU to exit and confirm current operation.
9. Press MENU again to exit and close TIMER setup mode. NOTE: WHEN THE TIMER IS SET, THE REC LED INDICATOR WILL BE ON. ALTHOUGH THE LIGHT MAY BE ON, THE

SYSTEM IS NOT NECESSARILY RECORDING SINCE IT WILL ONLY RECORD DURING ITS SCHEDULED TIME.

(Menu) Search ►Timer · Record Camera

Page 14 of the LOREX Technology DGN209 user manual — Record Settings
Page 14 · click to enlarge
Page 14

Record Settings On the Main menu, selecting the Record option will allow you to set the quality and speed of recordings. Pressing ENTER after scrolling to the Record option will bring up the following menu options:

(Menu) Search Timer ► Record

Camera System Event Network

HDD Overwrite Setup 1. Press ENTER to confirm HDD OVERWRITE setup. 2. Press ▲ / ▼ to choose HDD OVERWRITE.

(RECORD) HDD Overwrite: NO Record IPS: 25A Record Quality: Normal Alarm Rec IPS: 25A Alarm Rec Quality: Normal Motion Trigger Record: ON

NO: When HDD full will stop recording YES: When HDD full will overwrite the HDD recording 3. Press MENU to exit and confirm current operation. 4. Press MENU again to exit and close HDD OVERWRITE setup mode.

Record IPS Setup 1. Press ENTER to confirm RECORD IPS setup. 2. Press ▲ / ▼ to choose IPS record speed. Note that ‘25A’ indicates 25 ips with audio.

NTSC: 25A, 15, 8, 4, 2, 1 PAL: 18A, 12, 6, 3, 2, 1 3. Press MENU to exit and confirm current operation. 4. Press MENU again to exit and close RECORD IPS setup mode.

Record Quality Setup 1. Press ENTER to confirm Record Quality setup. 2. Press▲ / ▼ to choose Record Quality level.

BEST, HIGH, NORMAL, BASIC 3. Press MENU to exit and confirm current operation. 4. Press MENU again to exit and close RECORD QUALITY setup mode.

Alarm REC IPS Setup 1. Press ENTER to confirm ALARM REC IPS setup. 2. Press ▲ / ▼ to choose ALARM REC IPS record speed.

NTSC: 25A, 15, 8, 4, 2, 1 PAL: 18A, 12, 6, 3, 2, 1 3. Press MENU to exit and confirm current operation. 4. Press MENU again to exit and close ALARM REC IPS setup mode. Alarm REC Quality Setup 1. Press ENTER to confirm ALARM REC QUALITY setup. 2. Press▲ / ▼ to choose ALARM REC QUALITY level.

BEST, HIGH, NORMAL, BASIC 3. Press MENU to exit and confirm current operation. 4. Press MENU again to exit and close ALARM REC QUALITY setup mode.

Page 15 of the LOREX Technology DGN209 user manual — TITLE DWELL ALARM RECORD
Page 15 · click to enlarge
Page 15

Motion Trigger Record 1. Press ENTER to confirm MOTION TRIGGER RECORD setup. 2. Press▲ / ▼ to toggle the option between ON and OFF. 1. Select “ON” to set up the motion trigger recording: It can automatically switch from stand-by mode to Recording Mode. The motion detection will change the scanning sequence and show “D” on the monitor. NOTE: The trigger recording time will depend on the ALARM DURATION mode setting. It will record from the last trigger time. For example, when the alarm duration setting is 1 min, the time recording time is from 9:00:00 to 9:01:00. If the motion detection trigged again at 9:00:40, the triggered recording time will from 9:00:00 to 9:00:40 and 9:00:40 to 9:01:40. The total recording time is 00:01:40. 2. Select ”OFF”: The screen shows the motion detection and will change the scanning sequence while in the recording mode and show “M” on the monitor.

Camera Channel Setup

To access the Camera option, press MENU followed by the 4-digit password. Use the ▲ / ▼ to scroll to the Camera option and press ENTER.

TITLE DWELL ALARM RECORD

---01 ON 5 5 5 LOW EVENT

---02 ON 5 5 5 LOW EVENT

---03 ON 5 5 5 LOW EVENT

---04 ON 5 5 5 LOW EVENT The options available in this section are as follows: Title This feature is used to assign a 6-character title to each camera input.

1. Press ▲ / ▼ to select the desired time camera channel (1-9), and then press ENTER .
2. Press ▲ / ▼ to select the desired character and ◄ / ►to move to the next character
3. Press MENU to confirm and exit the Title setting. 4. Press MENU again to exit the Camera Setup Option. Dwell This feature is used to enable or disable the dwell feature for each camera when viewing using the call monitor output.
1. Press ▲ / ▼ to select the desired time camera channel (1-9), then press ENTER .
2. Press ◄ / ► to select the Dwell feature on the screen. 3. Press MENU to confirm and exit the dwell setting. 4. Press MENU again to exit the Camera Setup Option. Brightness / Contrast / Color This feature is used to adjust the video settings on each channel.
1. Press ▲ / ▼ to select the desired time camera channel (1-9), then press ENTER .
2. Press ◄ / ► to select the Brightness, Contrast, or Color feature on the screen.
3. Press ▲ / ▼ to select 0~9 on the screen.
4. Press MENU to confirm and exit the Brightness, Contrast, or Color control feature 5. Press MENU again to exit the Camera Setup Option. Alarm Polarity This feature is used to select the alarm polarity as LOW / OFF / HIGH.
1. Press ▲ / ▼ to select the desired time camera channel (1-9), then press ENTER .
2. Press ◄ / ► to select the Alarm Polarity feature on the screen.
3. Press ▲ / ▼ to select LOW / OFF / HIGH on the screen.
4. Press MENU to confirm and exit the Alarm Polarity feature 5. Press MENU again to exit the Camera Setup Option.
Page 16 of the LOREX Technology DGN209 user manual — Motion Trigger Record
Page 16 · click to enlarge
Page 16

Record Method This feature is used to select the DVR record method as either EVENT / NORMAL / OFF.

1. Press ▲ / ▼ to select the desired time camera channel (1-9), then press ENTER .
2. Press ◄ / ► to select the Record Method feature on the screen.
3. Press ▲ / ▼ to select EVENT / NORMAL / OFF on the screen.

EVENT: When the alarm input is triggered, the DVR will increase the recording time to that channel.

i.e. the normal record sequence for cameras is Camera 1, Camera 2, Camera 3 etc. In Event mode, when an alarm in triggered from channel 1, the DVR will record using the following sequence: Camera 1, Camera 2, Camera 1, Camera 3, Camera 1, Camera 4 etc. NORMAL: When an External Audible Alarm is triggered, the DVR will record normally as set up. OFF: An Alarm Trigger will not cause the DVR to start recording. 4. Press MENU to confirm and exit the Record Method feature. 5. Press MENU again to exit the Camera Setup Option

Page 17 of the LOREX Technology DGN209 user manual — Motion Detection
Page 17 · click to enlarge
Page 17

Motion Detection The Motion Detect feature provides a visual indication on the monitor when movement is detected in the picture. Also, if the ‘Motion Trigger Record’ option is enabled in the ‘Record’ menu, recording will activate on all cameras when motion is detected. Use the steps below to enable/disable the detection zones for each camera. Press MENU to enter the menu set up, then ▼ to CAMERA setup. Press ENTER twice to enter the Motion Detection setup. Each screen displays the current camera picture overlaid with the motion targets (as Figure 1). Pressing the ◄ / ►, ▲ / ▼ buttons will toggle the motion detection between ON or OFF. The targets on each motion setup can be turned to ON or OFF individually by row. To set up targets, using the following front panel buttons:

1. Press ENTER to confirm the channel. 2. Press ENTER to enter motion mode. 3. ▲ moves the target cursor up one row at a time. 4. ▼ moves the target cursor down one row at a time. 5. ◄ moves the target cursor left one column at a time. 6. ► moves the target cursor right one column at a time. 7. Press ENTER to turn the target cursor ON. Press ENTER again to turn the target cursor OFF. 8. Camera Select (1-15) toggles the corresponding target on the cursor line ON or OFF. (see Figure 1.1) There are only 15 targets in a row, therefore; only Camera Selected (1-15) can be operated. 9. Zoom: turns all targets in the current row ON or OFF. (Figure 1-2) 10. PIP: turns all targets on the screen ON or OFF. (Figure 1-3) Press SLOW button to setup the Sensitivity list up to 255

1. Press REC button to setup the Sensitivity list down to 000. 2. Sensitivity value is related to motion and brightness change. 3. Low value (as 001) means higher sensitivity on motion and brightness change. 4. High value (as 255) means lower sensitivity on motion and brightness change. User can choose the suitable sensitivity value in different locations. The default value is set on 32.

Figure 1 MOTION DETECTION SETUP

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

LOREX Technology DGN209 — Motion Detection diagram (page 17)
Fig. 9 · Motion Detection
Page 18 of the LOREX Technology DGN209 user manual — Motion Detection
Page 18 · click to enlarge
Page 18

Figure 1-1 MOTION DETECTION SETUP – 1~9

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

LOREX Technology DGN209 — Motion Detection diagram (page 18)
Fig. 10 · Motion Detection

Figure 1-2 MOTION DETECTION SETUP – LINE

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

LOREX Technology DGN209 — Motion Detection diagram (page 18)
Fig. 11 · Motion Detection

Figure 1-3 MOTION DETECTION SETUP – ALL

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

LOREX Technology DGN209 — Motion Detection diagram (page 18)
Fig. 12 · Motion Detection
Page 19 of the LOREX Technology DGN209 user manual — Selecting the Audio Input Channel
Page 19 · click to enlarge
Page 19

System Setup The System menu is used to configure the system level options on the DXR209. To access the System features, press MENU followed by the 4-digit password. Use the ▲ / ▼ to scroll to the ‘System’ option and press ENTER.

(SYSTEM) o Audio Input: 1 Int Audible Alarm: ON Ext Audible Alarm: ON Motion Audible Alarm: ON Alarm Duration: 10 SEC Dwell Time: 02 SEC Message Latch: NO Title Display: ON Time Display: Y/M/D 2003-JAN-02 (THU) 17:37:09 New Password: XXXX Clear HDD: NO System Reset: NO

Using the ▲ / ▼ buttons, scroll to the desired option and press ENTER to select it.

Selecting the Audio Input Channel

This feature is used to select the audio channel to record. To set this Audio Input Channel:

1. On the System screen, press ▲ / ▼ to select Audio Input, then press ENTER .
2. Press ▲ / ▼ to select the desired time audio channel (1-4).
3. Press MENU to confirm your change.
4. Press ▲ / ▼ to move to another field on the System screen or press MENU to exit.

Setting the Internal Audible Alarm Buzzer To enable or disable the Internal Audible Alarm Buzzer: If enabled, the buzzer will sound when the external alarm input is activated.

1. On the System screen, press ▲ / ▼ to select Internal Audible Alarm Buzzer, then press ENTER .
2. Press ▲ / ▼ to enable or disable the Internal Audible Alarm Buzzer. Options are:

ON = Buzzer is on. When the DVR detects an alarm, the system sounds the internal buzzer to alert the user. OFF = Buzzer is off. 3. Press MENU to confirm your change.

4. Press ▲ / ▼ to move to another field on the System screen or press MENU to exit.

Setting the External Audible Alarm Device To enable or disable the External Audible Alarm Device:

1. On the System screen, press ▲ / ▼ to select External Audible Alarm Device, then press ENTER .
2. Press ▲ / ▼ to enable or disable the External Audible Alarm Device. Options are:

ON = External Device is on. When the DVR detects an alarm, the system triggers the external audible alarm. OFF = External Device is off 3. Press MENU to confirm your change.

Page 20 of the LOREX Technology DGN209 user manual — Selecting the Date Display Format
Page 20 · click to enlarge
Page 20
4. Press ▲ / ▼ to move to another field on the System screen or press MENU to exit.

Setting the Motion Audible Alarm feature If enabled, the buzzer will sound if the video Motion Detect Feature is set and motion is detected.

1. On the System screen, press ▲ / ▼ to select Motion Audible Alarm, then press ENTER .
2. Press ▲ / ▼ to enable or disable the Motion Audible Alarm. Options are:

ON = Buzzer will sound when motion is detected. OFF = The buzzer will remain silent when motion is detected. 3. Press MENU to confirm your change.

4. Press ▲ / ▼ to move to another field on the System screen or press MENU to exit.

Setting the Alarm Duration To set the duration of the Alarm:

1. On the System screen, press ▲ / ▼ to select Alarm Duration, then press ENTER .
2. Press ▲ / ▼ to select the desired time (10s, 15s, 20s, 30s, 1min, 2min, 3min, 5min, 10min, 15min, 30min, always)
3. Press MENU to confirm your change.
4. Press ▲ / ▼ to move to another field on the System screen or press MENU to exit.

Setting the Dwell Time This timer is used to select the amount of time (between 1-10s) a channel appears on the call monitor before sequencing to the next channel. To Set the Dwell Time:

1. On the System screen, press ▲ / ▼ to select Dwell Time, then press ENTER .
2. Press ▲ / ▼ to select the desired time (1-10s).
3. Press MENU to confirm your change.
4. Press ▲ / ▼ to move to another field on the System screen or press MENU to exit.

Setting the Message Latch Feature This feature determines if the On Screen messages will remain on the screen or disappear after 10s. To set the Message Latch:

1. On the System screen, press ▲ / ▼ to select Message Latch, then press ENTER .
2. Press ▲ / ▼ to enable or disable the Message Latch feature. Options are:

NO = Screen messages will disappear after a 10 sec. (this is the default setting) YES = On Screen messages will remain on the screen for the duration of the event. 3. Press MENU to confirm your change.

4. Press ▲ / ▼ to move to another field on the System screen or press MENU to exit.

System Time/Date Set up

Selecting the Date Display Format

1. On the System screen, press ▲ / ▼ to select Date Display, then press ENTER .
2. Press ▲ / ▼ to choose a display format. Options are:

Y-M-D = Year - Month - Day M-D-Y = Month - Day - Year

Page 21 of the LOREX Technology DGN209 user manual — Resetting System to Factory Defaults
Page 21 · click to enlarge
Page 21

D-M-Y = Day - Month - Year Off = The date and time will not show on the screen. 3. Press MENU to confirm your change.

4. Press ▲ / ▼ to move to another field on the System screen or press MENU to exit this screen and confirm the current operation.

Setting System Time & Date

1. On the System screen, press ▲ / ▼ to select System Time & Date, then press ENTER .
2. Press ▲ / ▼ to choose a number, then press ◄ / ►to move to the next digit:

2003-Jan-01 (Mon) 22:38:29 3. Press MENU to confirm your change.

4. Press ▲ / ▼ to move to another field on the System screen or press MENU to exit this screen and confirm the current operation.

Changing the System Password

1. On the System screen, press ▲ / ▼ to select New Password, then press ENTER .
2. Press ▲ / ▼ to choose a number, then press ◄ / ► to move to the next digit.
3. Press MENU to confirm your change.
4. Press ▲ / ▼ move to another field on the System screen or press MENU to exit this screen and confirm the current operation. 5. If you have completed all your system configuration changes, press MENU again to exit and close menu setup.

Clearing the Hard Drive Data This option will erase all data from the hard drive. Ensure that there are no important recordings on the disk before using this option.

1. On the System screen, press ▲ / ▼ to select Clear HDD, and then press ENTER .
2. Press ▲ / ▼ to choose YES to clear the HDD or NO to leave as is.

All Data in HDD Will Be Cleared Are you sure? (◄ : No ► : Yes )

3. When you choose “Yes” on this option and press ENTER , the DVR will prompt: 4. Press ►to confirm clearing, or ◄ to cancel. 5. Press MENU to confirm your change.
6. Press ▲ / ▼ to move to another field on the System screen or press MENU to exit this screen and confirm the current operation. NOTE: Clearing the data from the Hard Drive results in permanent, irreversible loss of all video and related data currently

stored on the Hard Drive.

Resetting System to Factory Defaults

Using the System Reset option will set all options back to factory default settings. Use the steps below to perform this option:

1. On the System screen, press ▲ / ▼ to select System Reset, and then press ENTER .
2. Press ▲ / ▼ to choose:

Yes = Confirm the system reset and load the default settings. No = Do not reset the system at this time. 3. Press MENU to exit this screen and confirm the current operation. If you have completed all your system configuration changes, press MENU again to exit and close menu setup. NOTE: This will not affect the time and date settings.

Page 22 of the LOREX Technology DGN209 user manual — 2002 – JAN –01 01:02:03
Page 22 · click to enlarge
Page 22

Event Log Viewing To access the Event Log Viewing option, press MENU followed by the 4-digit password. Use the ▲ / ▼ to scroll to the Event option and press ENTER to view the list of logged events. Use the ▲ / ▼ to scroll through the events on the display and ◄ / ► to go to the next page. To view the video associated with an event, scroll to the event and press ENTER. The following is a list of events that can be displayed on the DXR209.

(Menu) Search Timer Record Camera System ► Event Network

M-HDD WARNING: Master HDD might be failed M-HDD LOSS: Master HDD does not exist. User can use other HDD. M-HDD ERROR: Master HDD may contain error. S-HDD WARNING: Slave HDD may have failed. S-HDD LOSS: Slave HDD does not exist. User can use other HDD S-HDD ERROR: Slave HDD may contain error. HDD FULL: HDD is full. SYSTEM ERROR: System may have failed. 02 VLOSS: Channel: 2 Video Loss 03 ALARM: Channel: 3 External I/O Alarm triggered. POWER RESTORE: Power restore.

Network To access the network option, press the MENU and use the ▲ / ▼ to scroll to the NETWORK option and press ENTER to view the list of options. The following is a list of network options that is displayed on the DXR209.

To obtain the following network addresses listed in the Menu screen above, please follow the software installation in the next section.

(Menu) Search Timer Record Camera System Event ► Network

(Network) SERVER IP 192.168.001.010 GATEWAY 192.168.001.065 NET MASK 255.255.255.000 DNS 168.095.001.001 WEB PORT 0080 REST DEFAULT NO

Operation

On Screen Display (OSD)

The DXR209 will display all current status on the OSD. Here is an example of the display. The following status will be shown: Time and Date – The current time and date will be shown on the first line. Record Type – The current recording method will be shown: M= Manual, T= Timer, A= Alarm, D= Motion Record Status – An ● icon will be displayed when the unit is currently recording.

2002 – JAN –01 01:02:03

D ● 32GB

Page 23 of the LOREX Technology DGN209 user manual — 2002 – JAN –01 01:02:03 A ● OW
Page 23 · click to enlarge
Page 23

HDD Status – This will display either the remaining HDD capacity in GB or OW to indicate that it is set to Overwrite. Video Loss - Screen will display if the video input is not connected properly.

Recording Methods

The DXR209 offers a variety of flexible recording modes. The unit can be set up to record continually, following a schedule, or by record events. In addition, the recording speed and resolution is also configurable (these options are configurable through the system menu). Under the recording status, if power is stopped accidentally, recorded video will still be stored in the HDD and will be available when the power is restored, and the original recording setup will remain. When recording, the top line of the display will show the date, time, and the amount of available HDD memory (in GB). In the example below, the letter “A” represents the alarm trigger and the letters “OW” represents HDD over write. There are 4 record modes for DXR209: Alarm Record, Timer Record, Manual Record and Motion Trigger Record.

2002 – JAN –01 01:02:03 A ● OW

1. Alarm Record The display will indicate a recording triggered by an Alarm using the letter “A”. 2. Timer Record The display will indicate a scheduled recording using the letter “T”. 3. Manual Record The display will indicate a manual recording (by pressing the REC button) using the letter “M”. 4. Motion Trigger Record Recording will be triggered by motion sensing and is indicated with the letter ‘D’. Viewing Options:

Individual Camera Select (1 - 9):

Press Camera Select (1 - 9) button to select the desired camera to display in full screen mode. Multi View Select:

This button is used to select the ideal viewing configuration.

1. Press the buttons to toggle the camera views. Picture in Picture (PIP):

This button is used to configure the monitor so a full screen is displayed in the background with a 1/16th size screen insert.

1. Press the button to display the PIP mode. 2. Press SELECT then ◄ / ► button to move the insert screen. 3. Press MENU to exit. Zoom:

Feature is used to enlarge the display (2X) the size of the main picture. The screen will now display the “zoomed” picture as the main picture with a small window inserted containing a moveable 1/4 view size of the appointed camera. 1. Select the desired camera by pressing Camera Select (1-9). 2. Press the Zoom button to zoom the image on the display. 3. Press the Zoom button again to move the zoom pointer. 4. Press MENU to exit.

Page 24 of the LOREX Technology DGN209 user manual — Playing Back Video
Page 24 · click to enlarge
Page 24

Video Search

The DVR allows you to easily find sections of recorded video using the Search feature. Press the SEARCH button and you will see the following options: Last Record: Plays the last recorded piece of video. Full List: Shows a listing of all recorded video on the HDD, sorted by time. Alarm List: Shows a listing of all recorded video triggered by an Alarm. Time Search: Finds video recorded on a specific date that is entered.

Full List Alarm List Time Search

An example of a Full List search is shown on the left. Note that the date and time appear, along with the letter representing the method of recording that took place. Simply press ENTER to view a selected piece of video on the list. The DVR will play that video, followed by the next video in chronological order, until it hits the End of the list. You can stop the video at any time by pressing the STOP button.

►M 2002-JAN-01 01:02:03 M-HDD M 2002-JAN-01 01:02:03 M-HDD A 2002-JAN-01 01:02:03 M-HDD T 2002-JAN-01 01:02:03 M-HDD E 2002-JAN-01 01:02:03 S-HDD M 2002-JAN-01 01:02:03 S-HDD

◄: Page Up ►: Page Down

Playing Back Video

Pressing PLAY while in Normal operation will play back the most recently recorded video clip. The controls below will allow you further controls over the playback whether in this mode or when viewing video from the Search mode. Fast Forward - Press PLAY on the front panel, then press FF/► to open the fast forward search screen.

Press FF/► once to increase the speed to 2X, twice to increase the speed to 4X, and so on. The maximum fast forward speed is 32X.

Fast Reverse - Press PLAY on the front panel, then press REW/◄ to open the fast reverse search screen. Press REW/◄ once to increase the reverse speed to 2X, twice to increase the reverse speed to 4X, and so on. The maximum fast rewind speed is 32X.

Slow Forward - Press PLAY on the front panel, then press SLOW for slow play. Press FF/► to play images at slow speed

(1/2X). Press FF/► again to slow the speed to 1/4X. Continue to press FF/► to slow down the speed. The minimum slow speed is 1/32X. Slow Reverse - Press PLAY on the front panel, then press SLOW for slow forward. Press REW/◄ to play images slowly

forward (1/2X). Press REW/◄ again to slow the speed to 1/4X. Continue to press REW/◄ to slow down the speed. The minimum slow forward speed is 1/32X. Image Jog - Press PLAY on the front panel, then press PAUSE to lock the current image on the screen. Press FF/► to select single image play. Each time you press FF/► the next image will display. Continuing to press FF/► will result in forward image-by-image playback. Pressing REW/◄ will result in reverse image by image playback. Pause - Press PLAY on the front panel, and then press PAUSE/▲ to lock the current image on the screen. Stop - Press STOP on the front panel whenever you want to return the DVR to live monitoring mode.

►Last Record

Page 25 of the LOREX Technology DGN209 user manual — STEP 1: SOFTWARE INSTALLATION – STATIC IP SETTING:
Page 25 · click to enlarge
Page 25

Hardware Connection from DVR

Static IP Setting

LOREX Technology DGN209 — Hardware Connection from DVR diagram (page 25)
Fig. 13 · Hardware Connection from DVR
1. Put the attached CD into the CD-ROM. The application program will install on your PC. Note: The CD contains a self-running installation that automatically starts when the CD is inserted. Follow the instructions for installation as indicated in the next few pages. 2. Press “Next”.

STEP 1: SOFTWARE INSTALLATION – STATIC IP SETTING:

LOREX Technology DGN209 — STEP 1: SOFTWARE INSTALLATION – STATIC IP SETTING: diagram (page 25)
Fig. 14
Page 26 of the LOREX Technology DGN209 user manual — Hardware Connection from DVR
Page 26 · click to enlarge
Page 26
3. Choose the destination location and press “Next”.
4. Set the program shortcut setting and press “Next”.
LOREX Technology DGN209 — Hardware Connection from DVR diagram (page 26)
Fig. 15 · Hardware Connection from DVR
5. Press “Next” to begin copying the files.
LOREX Technology DGN209 — Hardware Connection from DVR diagram (page 26)
Fig. 16 · Hardware Connection from DVR
LOREX Technology DGN209 — Hardware Connection from DVR diagram (page 26)
Fig. 17 · Hardware Connection from DVR
Page 27 of the LOREX Technology DGN209 user manual — STEP 2: STATIC IP SETTING
Page 27 · click to enlarge
Page 27
6. After the installation, the following files listed below will appear in your assigned path or file folder. There will be 6 files and 1 folder.
LOREX Technology DGN209 — STEP 2: STATIC IP SETTING diagram (page 27)
Fig. 18

STEP 2: STATIC IP SETTING

In the DVR MENU / NETWORK set the IP ADDRESS, GATEWAY, NET MASK, DNS and WEB PORT as provided from your local ISP (internet service provider).

When all of the network settings are finished, connect the DVR to the internet (computer).

Below is an example of the settings required:

(MENU) SEARCH TIMER RECORD CAMERA SYSTEM EVENT XNETWORK

LOREX Technology DGN209 — STEP 2: STATIC IP SETTING diagram (page 27)
Fig. 19

(NETWORK) SERVER IP 61.66138.74 GATEWAY 61.66.138.254 NET MASK 255.255.255.000 DNS 168.095.001.001 WEB PORT 00080 RESET DEFAULT NO

LOREX Technology DGN209 — STEP 2: STATIC IP SETTING diagram (page 27)
Fig. 20
3. Connecting the PC and DVR via the Internet
1. To configure the Server IP, please click twice to enter the setup. 2. Key in the User Name, Password, and Server IP (The default setting for the User Name is admin and the default Password is admin ; Server IP is the address that you set in Step 2). Click on OK to connect.
LOREX Technology DGN209 — STEP 2: STATIC IP SETTING diagram (page 27)
Fig. 21
Page 28 of the LOREX Technology DGN209 user manual — WHAT IS A DYNAMIC IP ADDRESS?
Page 28 · click to enlarge
Page 28

Dynamic IP Setting

WHAT IS A DYNAMIC IP ADDRESS?

A Dynamic IP Address is an IP (Internet Protocol) address that changes each time you connect to the internet. This cuts down on the number of IP addresses large consumer providers need because not all of their customers are using the service at any given time. It also cuts down on bandwidth usage by preventing consumers from hosting servers. Note: a number of companies have started to offer services aimed at updating DNS for dynamically connected clients. STEP 1: SOFTWARE INSTALLATION – DYNAMIC IP SETTING: Follow the same procedure as outlined on Page 19 for the Static IP Setting. STEP 2: DDNS REGISTRATION FOR A DYNAMIC IP ADDRESS: 1. You must have a gateway router that supports DDNS (Dynamic Domain Network Service). Please go to www.dlink.com or www.linksys.com for a list of available routers. To register for a dynamic IP address click on the free site “http://www.dyndns.org” and click on “Account” (please look at the example below).

LOREX Technology DGN209 — WHAT IS A DYNAMIC IP ADDRESS? diagram (page 28)
Fig. 22
2. Click on “Create Account”.
3. Register your information (Username, E-mail address & password). Click on “Create Account” when the necessary information is completed.
LOREX Technology DGN209 — WHAT IS A DYNAMIC IP ADDRESS? diagram (page 28)
Fig. 23
LOREX Technology DGN209 — WHAT IS A DYNAMIC IP ADDRESS? diagram (page 28)
Fig. 24
Page 29 of the LOREX Technology DGN209 user manual — POWER
Page 29 · click to enlarge
Page 29
4. After registering your account, you will receive an e-mail, which contains instructions to activate your account. If you do not follow these directions within 48 hours, you will need to re-register your account.
5. Login your account.
LOREX Technology DGN209 — Dynamic IP Setting diagram (page 29)
Fig. 25 · Dynamic IP Setting
6. Click on “Account” and “Add Host”
LOREX Technology DGN209 — Dynamic IP Setting diagram (page 29)
Fig. 26 · Dynamic IP Setting
7. Users can set up their own DDNS HOST. For example, the user’s Host name is “Lorex.dyndns.org”. Click on “Add Host” to finish the setting. (NOTE: Some routers don’t support some DDNS HOSTs)
LOREX Technology DGN209 — Dynamic IP Setting diagram (page 29)
Fig. 27 · Dynamic IP Setting

E STEP 3: CONNECTING THE PC TO A ROUTER / ROUTER LOGIN: NOTE: The following settings are different from router to router. Please read the instructions on your router thoroughly. 1. Connect the PC to the router using the LAN cable (LAN end).

LOREX Technology DGN209 — Dynamic IP Setting diagram (page 29)
Fig. 28 · Dynamic IP Setting

POWER

Lorex · LAN end

Page 30 of the LOREX Technology DGN209 user manual — Click twice
Page 30 · click to enlarge
Page 30
2. Network setting for PC. (The instruction is based on Win XP O/S. If your O/S is Win 2000 or Win 2003, the setup procedure is similar to that of Win XP O/S.)
3. Click on “Properties” for TCP/IP setup.
LOREX Technology DGN209 — Dynamic IP Setting diagram (page 30)
Fig. 29 · Dynamic IP Setting
LOREX Technology DGN209 — Dynamic IP Setting diagram (page 30)
Fig. 30 · Dynamic IP Setting
LOREX Technology DGN209 — Dynamic IP Setting diagram (page 30)
Fig. 31 · Dynamic IP Setting

Local Area Connection Enabled Realtek RTL8139 Family

Local Area Connection Enabled Realtek RTL8139 Family

Click twice

Click twice

LOREX Technology DGN209 — Click twice diagram (page 30)
Fig. 32 · Click twice
4. Click on “INTERNET PROTOCOL (TCP/IP)” and then select “Properties” to setup.
LOREX Technology DGN209 — Click twice diagram (page 30)
Fig. 33 · Click twice
Page 31 of the LOREX Technology DGN209 user manual — Dynamic IP Setting
Page 31 · click to enlarge
Page 31
5. Choose “Obtain an IP address automatically”.
LOREX Technology DGN209 — Dynamic IP Setting diagram (page 31)
Fig. 34 · Dynamic IP Setting
6. Enter the “Command Prompt”.
7. In the setting window, enter “ ipconfig” , and write down the router’s gateway (e.g. 192.168.1.1).
LOREX Technology DGN209 — Dynamic IP Setting diagram (page 31)
Fig. 35 · Dynamic IP Setting
LOREX Technology DGN209 — Dynamic IP Setting diagram (page 31)
Fig. 36 · Dynamic IP Setting
8. Close the window above. Enter the IP address (router’s gateway: 192.168.1.1) to log in to the router from the Internet Explorer. Enter the login web page and key in the router’s user name and password.
Page 32 of the LOREX Technology DGN209 user manual — SVC
Page 32 · click to enlarge
Page 32
LOREX Technology DGN209 — Dynamic IP Setting diagram (page 32)
Fig. 37 · Dynamic IP Setting
4. ROUTER SETTING (Please refer to your Router manual for the configuration ) NOTE: In the router setting, there are four steps to follow: 1. Dial setting 2. DHCP setting 3. Virtual server setting 4. DDNS setting
1. Click on “INTERNET PORT” and choose your WAN type (e.g. PPPoE). Enter your “User Name” and “Password” to dial up the dynamic IP address. Press save after you set up.
2. Press “LOCAL PORT” and set “Start IP address” and “Number of IP address”. (For example, if the IP address of your Video Web Server is 192.168.1.10, then 10 is excluded from the setting range.) Press save after you finish setting up.
LOREX Technology DGN209 — Dynamic IP Setting diagram (page 32)
Fig. 38 · Dynamic IP Setting

SVC

LOREX Technology DGN209 — SVC diagram (page 32)
Fig. 39
Page 33 of the LOREX Technology DGN209 user manual — ADSL modem (WAN end)
Page 33 · click to enlarge
Page 33
3. In the “ADVANCED SETUP / Virtual Server”. Choose “By Port” and set the “Port Number” to 80 for the Video Web Server. Set the “Local Server IP Address” to 192.168.1.10. (The default Video Web Server IP and port). Press add & save after you set up.
4. In the “ADVANCED SETUP / Dynamic DNS”, key in the “DNS Account”, “User Name” and “Password” that you applied in step 3. Press save after you set up.
LOREX Technology DGN209 — STEP 5 : IP SETTING diagram (page 33)
Fig. 40
LOREX Technology DGN209 — STEP 5 : IP SETTING diagram (page 33)
Fig. 41

STEP 5 : IP SETTING

In the DVR MENU / NETWORK set the IP ADDRESS, GATEWAY, NET MASK, DNS and WEB PORT.

6. Connect Router

Below is an example of the settings required:

(MENU) SEARCH TIMER RECORD CAMERA SYSTEM EVENT XNETWORK

(NETWORK) SERVER IP 61.66138.74 GATEWAY 61.66.138.254 NET MASK 255.255.255.000 DNS 168.095.001.001 WEB PORT 00080 RESET DEFAULT NO

ADSL modem (WAN end)

Page 34 of the LOREX Technology DGN209 user manual — STEP 7 : Connect to the DVR via the Internet
Page 34 · click to enlarge
Page 34
7. Connect to the DVR via the Internet 1. Change PC network setting to the original setting and link PC to the internet . 2. Click twice and enter your User name, Password and host on the Video Web Server. (Note: If you did not change the “Account” , the User Name and Password are both “admin”.) Click OK to connect. Example:

There are two ways to get the software: one is via the attached CD, and the other is via the Video Web Server. Address Book You can press the “Address Book” button to add a new IP or choose any login IP address to access the Video Server. This function is designed to store a list of IP addresses which you can control and manage. Backup Program You can press “ ” button and backup all related files of this application program to any storage device that you want (for example: any hard disk or USB Flash Drive). Play last record file You can press “ ” button and you can play the last recorded file.

LOREX Technology DGN209 — STEP 7 : Connect to the DVR via the Internet diagram (page 34)
Fig. 42 · STEP 7 : Connect to the DVR via the Internet

The default value for the web port is 80. If you change this port you will also need to make the same change in the software, and also in the Internet Explorer Address. For example , if you change this port to 2000 then the IP Address would be 61.62.147.111:2000

Play the last record file

LOREX Technology DGN209 — STEP 7 : Connect to the DVR via the Internet diagram (page 34)
Fig. 43 · STEP 7 : Connect to the DVR via the Internet

Backup Program

Page 35 of the LOREX Technology DGN209 user manual — Software Operation at the Remote Site
Page 35 · click to enlarge
Page 35

Software Operation at the Remote Site

Follow the steps below to connect to a remote site. (e.g. If you set up the server at your office with one static ADSL, you can remotely watch the video anywhere, with a networkable computer.)

1. Click twice to enter the Login setup (please refer to “software installation”).
2. Key in “User Name” and “Password”. Click “OK” to establish the connection.

Example:

LOREX Technology DGN209 — Software Operation at the Remote Site diagram (page 35)
Fig. 44 · Software Operation at the Remote Site
3. If you see the video screen, then you have successfully connecting to the server.
LOREX Technology DGN209 — Software Operation at the Remote Site diagram (page 35)
Fig. 45 · Software Operation at the Remote Site
Page 36 of the LOREX Technology DGN209 user manual — Control Panel and Basic Operation
Page 36 · click to enlarge
Page 36

Control Panel and Basic Operation

A. Video Web Server control panel

1. Image transmission rate per second. 2. Data transmission rate. 3. Connection/Disconnection. 4. Resolution: D1,CIF 5. Image quality: High, Middle, Low. 6. Image adjusting: Brightness/ Contrast/ Saturation. 7. Snapshot: press this button, to automatically save the image on your PC. 8. Record: press this button to record the files and automatically save them on your PC. 9. System Configuration. 10. Number of online users.

1 2 3 4 5 6 7 8 9 10

LOREX Technology DGN209 — Control Panel and Basic Operation diagram (page 36)
Fig. 46 · Control Panel and Basic Operation
Page 37 of the LOREX Technology DGN209 user manual — 2004/11/17 11:52:32 2004-NOV-17 25:45:03 M y OW
Page 37 · click to enlarge
Page 37

B. Digital device control panel

1. CH1-9 2. 4cut, 7cut, 9cut, PIP 3. Zoom, Select, Lock, Record 4. Stop, Rewind, Fast Forward, Pause, Slow, Play 5. Menu (Exit), Left, Right, Up, Down 6. Enter 7. TURBO*
LOREX Technology DGN209 — B. Digital device control panel diagram (page 37)
Fig. 47 · B. Digital device control panel

*TURBO: Activate the turbo button when you would like to shift the selection more quickly by jumping 6 selections at a time.

Play Back Operation

You will find the recorded file on the PC. Click twice to playback.

1 2 3 4 5 6 7 8 9 11 12 13

1. On Screen Display 2. Snapshot 3. Stop 4. Pause 5. Slow (1/2X, 1/4X,1/8X,1/16X, 1/32X) 6. PLAY 7. Fast (2X, 4X, 8X, 16X, 32X) 8. OSD show / hide 9. System setting (Path of snapshot, text color, progress color, channel color) 10. Last Video 11. Next Video 12. Duration time / Status 13. Playback controlling bar
LOREX Technology DGN209 — Play Back Operation diagram (page 37)
Fig. 48 · Play Back Operation

2004/11/17 11:52:32 2004-NOV-17 25:45:03 M y OW

100%

61.66.138.74 PAL_CIE

Page 38 of the LOREX Technology DGN209 user manual — SYSTEM CONFIG
Page 38 · click to enlarge
Page 38

Advanced Settings

Click on “System Config” for advanced setting.

ACCOUNT

SYSTEM CONFIG

ALARM

LOREX Technology DGN209 — SYSTEM CONFIG diagram (page 38)
Fig. 49

Set up the user’s account (Max 10 accounts), password and authority (Max 5 accounts on line at the same time).

1. User’s level: SUPERVISORcontrols all the functions HIGH LEVELcontrols advanced functions NORMAL - controls basic functions only GUEST LEVEL - watch the image only 2. Life time: During this period of time, users are allowed to control the Video Web Server.
LOREX Technology DGN209 — SYSTEM CONFIG diagram (page 38)
Fig. 50

Set up the ALARM function. You can use it to operate the “alarm trigger recording” function.

1. Alarm Trigger: Enable or disable Alarm trigger function. 2. Alarm Method : Two selections—E-mail or FTP. 3. Image Resolution : Image storing resolution for Email or FTP function(CIF is

176 *144; D1 is 352*288) 4. Alarm refresh: Clear the alarm message “ ” which is showed on the screen. * When the motion detection is triggered, the DVR will send the alarm image to notify the users.

Page 39 of the LOREX Technology DGN209 user manual — FILE PATH
Page 39 · click to enlarge
Page 39

MAIL

FTP

LOREX Technology DGN209 — MAIL diagram (page 39)
Fig. 51

When the alarm is triggered, the video server program will capture the instant picture and e-mail the captured image to the assigned recipients.

1. Get all the data from the ISP company or by mailing it to the server supplier. (POP3/SMTP server) 2. Set the mail list which you want to send to when the alarm is triggered. 3. If it is not necessary for you to verify the password and user’s name, please choose Verify as “No”.

FILE PATH

LOREX Technology DGN209 — FILE PATH diagram (page 39)
Fig. 52

When the alarm is triggered, the video server program will capture the instant picture and upload the captured image to the assigned FTP site.

1. Get all the data from the ISP company. 2. The default uploading port is No.21. 3. Set the uploading directory.
LOREX Technology DGN209 — FILE PATH diagram (page 39)
Fig. 53

You can modify the storing path for the recording file and snapshot images.

Page 40 of the LOREX Technology DGN209 user manual — VIDEO WEB SERVER – MICROSOFT INTERNET EXPLORER
Page 40 · click to enlarge
Page 40

TOOL BOX

ONLINE USER

LOREX Technology DGN209 — TOOL BOX diagram (page 40)
Fig. 54

Upgrade the firmware and get the online users’ information. NOTE: Do not reboot the DVR while it is upgrading the firmware. 1. Firmware Version: For the current

firmware version, you can click on the “Find” button to get the latest firmware from your PC. Press “Upgrade Firmware” to upgrade it. 2. Turbo step: Activate the turbo button when you would like to shift the selection by jumping 6 selections at a time.

Connecting the Video Web Server Via the Internet Explorer Browser

LOREX Technology DGN209 — Connecting the Video Web Server Via the Internet Explorer Browser diagram (page 40)
Fig. 55 · Connecting the Video Web Server Via the Internet Exp…

Get online users information

1. Info refresh : Refresh the online users information

You can also connect to the Video Web Server via the Internet Explorer browser. This function is suitable for both WIN 2000 and WIN XP (WIN XP is preferable over WIN 2000). Step 1: Enter the IP address that you want to connect to. (see example below)

LOREX Technology DGN209 — Connecting the Video Web Server Via the Internet Explorer Browser diagram (page 40)
Fig. 56 · Connecting the Video Web Server Via the Internet Exp…

VIDEO WEB SERVER – MICROSOFT INTERNET EXPLORER

61.66.138.74

Page 41 of the LOREX Technology DGN209 user manual — Connecting the Video Web Server Via the Internet Explorer Browser
Page 41 · click to enlarge
Page 41
2. Enter your Username and Password to login to the Video Web Server.
LOREX Technology DGN209 — Connecting the Video Web Server Via the Internet Explorer Browser diagram (page 41)
Fig. 57 · Connecting the Video Web Server Via the Internet Exp…
3. Click on “YES” to confirm that the Download Application is authentic and has been verified.
LOREX Technology DGN209 — Connecting the Video Web Server Via the Internet Explorer Browser diagram (page 41)
Fig. 58 · Connecting the Video Web Server Via the Internet Exp…
Page 42 of the LOREX Technology DGN209 user manual — Key Lock
Page 42 · click to enlarge
Page 42
4. After you login, you will see the Video Web Server screen (example below).

2 3 4 5 6 7 8 9

LOREX Technology DGN209 — Key Lock diagram (page 42)
Fig. 59 · Key Lock
1. Image transmission rate per second 2. Data transmission rate 3. Video Channel 4. Resolution:D1,CIF 5. Image quality: High, Middle, Low 6. Number of online users 7. Channel switching button 8. Resolution switching button
9. Quality switching button 10. Menu, Left, Right, Up, Down, Exit 11. Lock, Enter, Zoom, Search, Select. 12. Stop, Play, Record, Rew, Fast, Pause, Slow, 13. Camera 14. 4cut, 7cut, 9cut, PIP 15. Position of view

Key Lock

For added security, you can Lock the buttons on your DXR209. Locking disables the functionality of the buttons and prevents accidental key presses from altering the operation of the DXR209.

To enable the Key Lock feature, press and hold the ENTER and MENU keys at the same time. To disable the Key Lock feature when it is locked, press the ENTER and MENU keys at the same time, key in the password (Default : 0000) and press the ENTER key again.

Page 43 of the LOREX Technology DGN209 user manual — SOLUTION PROBLEM
Page 43 · click to enlarge
Page 43

Troubleshooting

SOLUTION PROBLEM

Need to insert HDD. Make sure that the HDD Cartridge is locked, then press any key to continue.

Check the power source cord connections. Check that there is power at the outlet. No Power

Buttons aren’t working when pressed

Check if the system is in Key Lock mode. Press MENU and ENTER at the same time and enter password to escape the Key Lock mode.

Check that the HDD has been installed correctly. No recorded video

Check that Timer / Alarm Enable is set to YES. Timer / Alarm recording isn’t working

Check camera’s video cables and connections. Check monitor’s video cables and connections. Make sure that the camera is receiving power.

HDD not found · No video

Page 44 of the LOREX Technology DGN209 user manual — Technical Specifications
Page 44 · click to enlarge
Page 44

Technical Specifications

Video format NTSC/EIA or PAL/CCIR

Network Interface Ethernet (10100 Base-T)

Protocols TCPIP, ICMP, SMTP, HTTP, FTP

Triggers & Actions E-mail images or images uploaded to FTP site / Remote recording

HDD storage IDE type, UDMA 66 above, 1 removable HDD supported

Record mode Manual / Alarm / Timer/Motion Trigger

Camera input signal Composite video signal 1 Vp-p 75Ω BNC, 9 Channels

Camera loop back Composite video signal 1 Vp-p 75Ω BNC, 9 Channels

Main monitor output Composite video signal 1 Vp-p 75Ω BNC

Call monitor output Composite video signal 1 Vp-p 75Ω BNC

Audio input/ output 4 audio inputs, (RCA) and 2 audio outputs, (RCA)

Motion detect area 15 X 12 Targets per camera (NTSC)/ 15*14 targets per camera (PAL)

Motion detect sensitivity 256 Levels

Video loss detection Yes

Refresh rate 72 IPS for NTSC / 100 IPS for PAL

Recording rate 25 IPS for NTSC / 12 IPS for PAL

Dwell time Programmable (1 - 10 Sec)

Picture in picture Yes (Moveable)

Picture zoom 2X (Moveable)

Camera title 6 Characters

Video adjustable Color / Contrast / Brightness Adjustable

Alarm input / output InputTTL input, Hi (5V), Low (GND) Output: COM,/N.O/N.C

Time display format YY/MM/DD, DD/MM/YY, MM/DD/YY, OFF

Power source AC 100-240V +/- 10% switching adaptor

Operation temperature 10 - 40 degrees C

Dimension (mm) 430 (W) x 65 (H) x 300 (D)

Net weight 5.4 Kgs

Key lock Yes · Power consumption

Page 45 of the LOREX Technology DGN209 user manual — Appendix 1: Installing the HDD
Page 45 · click to enlarge
Page 45

Appendix 1: Installing the HDD

more complicated. Please follow the next steps carefully in order to ensure proper installation. The compartment (with the handle) located on the front panel of the DXR209 is the removable Cartridge Casing where the HDD is inserted. The various parts of the Cartridge Casing are labeled for your reference.

LOREX Technology DGN209 — Appendix 1: Installing the HDD diagram (page 45)
Fig. 60 · Appendix 1: Installing the HDD
1. Keyhole 2. LED indicator lights (Power indicator & HDD Access indicator) 3. Handle Step 1: Remove the Cartridge Casing from the DXR209. Lift the handle and pull towards you. The Cartridge Casing will slide out of the DXR209. NOTE : The Cartridge must be unlocked to remove it, (please see step 8 for more information on locking and unlocking the

removable HDD cartridge). Step 2: Remove the Cover from the Cartridge Casing. Step 3: Unclip the release latch with the word “OPEN,” printed beside it by gently pushing on the latch. Step 4: Slide the cover off the Cartridge Casing.

LOREX Technology DGN209 — Appendix 1: Installing the HDD diagram (page 45)
Fig. 61 · Appendix 1: Installing the HDD
LOREX Technology DGN209 — Appendix 1: Installing the HDD diagram (page 45)
Fig. 62 · Appendix 1: Installing the HDD
5. Insert the HDD into the Cartridge Casing. Take the Hard Disk Drive and connect the two cables from the back of the Cartridge Casing to the HDD. The cables should be pushed in firmly, but not forcibly.
LOREX Technology DGN209 — Appendix 1: Installing the HDD diagram (page 45)
Fig. 63 · Appendix 1: Installing the HDD

Cartridge Casing

Page 46 of the LOREX Technology DGN209 user manual — Appendix 1: Installing the HDD
Page 46 · click to enlarge
Page 46

Step 6: Secure the HDD in the Cartridge Casing. Position the HDD into place and secure it using the six screws supplied. Step 7: Slide the top Cover over the Cartridge Casing. Slide the Cover forward over the Cartridge Case. Ensure it is secured in place over the release latch. Reinsert the Cartridge Casing into the DXR209 Step 8: Lock the Cartridge To Lock the cabinet, turn the key clockwise to Position A. To unlock the cabinet, turn the key counter-clockwise to Position B. NOTE: The DXR209 will not function if the key is not in the locked position. 1. The HDD should be selected as “Master “. 2. This product does not support hot swap. Please power off the unit before removing HDD. 3. Approved models and manufactures of HDD are listed in Appendix #6 and have been tested and proven compatible with this DVR. 4. Please remove hard disk drive ONLY after power is shut off for more than 60 seconds. This would protect and extend the operating life of the hard disk drive. 5. HDD should be set up by selecting HDD Jumper.

LOREX Technology DGN209 — Appendix 1: Installing the HDD diagram (page 46)
Fig. 64 · Appendix 1: Installing the HDD
LOREX Technology DGN209 — Appendix 1: Installing the HDD diagram (page 46)
Fig. 65 · Appendix 1: Installing the HDD
LOREX Technology DGN209 — Appendix 1: Installing the HDD diagram (page 46)
Fig. 66 · Appendix 1: Installing the HDD

A (locked) · B (unlocked)

Page 47 of the LOREX Technology DGN209 user manual — Appendix 2: Connection Diagram to Cameras and Monitor
Page 47 · click to enlarge
Page 47

Appendix 2: Connection Diagram to Cameras and Monitor

LOREX Technology DGN209 — Appendix 2: Connection Diagram to Cameras and Monitor diagram (page 47)
Fig. 67 · Appendix 2: Connection Diagram to Cameras and Monito…
Page 48 of the LOREX Technology DGN209 user manual — PIN 10,14 ---- PIN OFF
Page 48 · click to enlarge
Page 48

Appendix 3: Pin Configurations

25 Pin Com Port

DVR

LOREX Technology DGN209 — DVR diagram (page 48)
Fig. 68

EXTERNAL ALAM NO EXTERNAL ALARM COM

PIN OFF ALARM INPUT 9 ALARM INPUT 10 ALARM INPUT 11 ALARM INPUT 12 ALARM INPUT 13 ALARM INPUT 14 ALARM INPUT 15 ALARM INPUT 16 ALARM INPUT 1 ALARM INPUT 2 ALARM INPUT 3 ALARM INPUT 4 ALARM INPUT 5 ALARM INPUT 6 ALARM INPUT 7 ALARM INPUT 8 PIN OFF GND

GND

PIN 1 GROUND

ALARM INPUT

PIN 2-9; PIN 15-22 To connect wire from ALARM INPUT (PIN 2 -- 9; PIN 15-22) to GND (PIN 1) connector, DVR will start recording and buzzer will sound. ¾ When Menu / Camera / Alarm is set to “Low”: the unit starts to record and the buzzer sounds. ¾ When Menu / Camera / Alarm is set up to “High”: the unit starts to record and the buzzer sounds.

PIN 10,14 PIN OFF

PIN13 Under normal operations COM disconnects with NO. When the Alarm is triggered, COM connects with NO. EXTERNAL ALARM NO

PIN 25 Under normal operations COM disconnects with NO. When the Alarm is triggered, COM connects with NO. EXTERNAL ALARM COM

Page 49 of the LOREX Technology DGN209 user manual — Appendix 4: Rack Mount Installation
Page 49 · click to enlarge
Page 49

Appendix 4: Rack Mount Installation

Screws and brackets for rack mounting applications can be purchased as an optional accessory.

Front Angle with Rack Mount (Optional)

Side View with Rack Mount (Optional) For more information about the rack mount & other accessories through Lorex, please visit: www.Lorexcctv.com

Page 50 of the LOREX Technology DGN209 user manual — NTSC SYSTEM
Page 50 · click to enlarge
Page 50

Appendix 5: Recording Times (in Hours)

NTSC SYSTEM

LOREX Technology DGN209 — NTSC SYSTEM diagram (page 50)
Fig. 69

Normal 32hr 64hr 120hr 240hr 480hr 960hr Record Quality

LOREX Technology DGN209 — NTSC SYSTEM diagram (page 50)
Fig. 70

Normal 48hr 96hr 1600hr 360hr 720hr 1440hr Record Quality

LOREX Technology DGN209 — NTSC SYSTEM diagram (page 50)
Fig. 71

Normal 64hr 128hr 240hr 480hr 960hr 1920hr Record Quality

Page 51 of the LOREX Technology DGN209 user manual — Western Digital Caviar WD2000BB-00DWA0 200GB 7200rpm
Page 51 · click to enlarge
Page 51

Appendix 6: Compatible HDD Brands

Manufacturer Model Capacity Rotation HITACHI Deskstar 180 GXP (120 GB) 120GB 7200 rpm HITACHI Deskstar 7K250, HDS722516VLAT20 160GB 7200rpm HITACHI Deskstar 7K250, HDS722525VLAT80 250GB 7200rpm

IBM Deskstar 120GXP (80GB) 80GB 7200 rpm IBM Deskstar 120GXP (120GB) 120GB 7200 rpm Maxtor DiamondMax 536DX(60GB) 4W060H4 60GB 5400rpm

Maxtor DiamondMax Plus 9 80GB 7200 rpm Maxtor DiamondMax Plus 9, Model#6Y120L 120GB 7200 rpm Maxtor DiamondMax Plus 9, Model#6Y160L0 160GB 7200rpm Seagate Barracuda ATA IV, ST380021A 80GB 7200rpm Seagate Barracuda ATA V, ST3120023A 120GB 7200 rpm

Seagate Barracuda 7200.7 Plus, ST3160023A 160GB 7200 rpm Western Digital Caviar WD1200BB-00CAA1 120GB 7200rpm

Western Digital Caviar WD2000BB-00DWA0 200GB 7200rpm

LOREX Technology DGN209 — Western Digital Caviar WD2000BB-00DWA0 200GB 7200rpm diagram (page 51)
Fig. 72 · Western Digital Caviar WD2000BB-00DWA0 200GB 7200rpm
Page 52 of the LOREX Technology DGN209 user manual — www.lorexcctv.com VISIT
Page 52 · click to enlarge
Page 52

It’s all on the web

Product Information

Specification Sheets

User Manuals

Software Upgrades

 Quick Start Guides

Firmware Upgrades

LOREX Technology DGN209 — User Manuals diagram (page 52)
Fig. 73 · User Manuals
LOREX Technology DGN209 — User Manuals diagram (page 52)
Fig. 74 · User Manuals

www.lorexcctv.com VISIT

www.lorexcctv.com

Strategic Vista International Inc.

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
HDD not foundNeed to insert HDD. Make sure that the HDD Cartridge is locked, then press any key to continue. p.43
No PowerCheck the power source cord connections. Check that there is power at the outlet. p.43
Buttons aren’t working when pressedCheck if the system is in Key Lock mode. Press MENU and ENTER at the same time and enter password to escape the Key Lock mode. p.43
No recorded videoCheck that the HDD has been installed correctly. p.43
Timer / Alarm recording isn’t workingCheck that Timer / Alarm Enable is set to YES. p.43
No videoCheck camera’s video cables and connections. Check monitor’s video cables and connections. Make sure that the camera is receiving power. p.43
No video p.43

Ask about the LOREX Technology DGN209

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LOREX Technology DGN209

Be the first to ask — other owners or our team will answer.

Original document

LOREX Technology DGN209 manual PDF

52 pages·3.1 MB·DVR·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…