Instruction/ maintenance manual of the product EZXS88W Linksys
Go to page of 10
Instant EtherFast ® Series EtherFast ® 10/100 Autosensing W orkgroup Switch Use This User Guide T o Install These Linksys Pr oducts • EtherFast ® 10/100 5-P ort W orkgroup Switch (EZXS55W) • Et.
.
COPYRIGHT & TRADEMARKS Copyright © 2000 Linksys, All rights reserved. Micr osoft, Windows, and the Windows logo are r egistered trademarks of Micr osoft Corporation. All other trademarks and brand names are the pr operty of their respective proprietors.
Introduction Y our EtherFast 10/100 Autosensing Workgroup Switch Congratulations on purchasing your new Linksys EtherF ast 10/100 Autosensing W orkg roup Switch for your netw ork's 10/100 mig ration needs.
3 EtherFast 10/100 Autosensing Switches Instant EtherFast ® Series 2 Hardware Installation Planning Y our Network Layout Building a F ast Ether net netw ork in v olves more topolo gy rules in addition to the 10BaseT netw ork rules. These rules specify distance limitations and cabling specif ications.
Powering On the Switch Plug in the Switch's AC po w er adapter . Each time your Switch po w ers up, it will run a Diagnostic/Self-T est. After the test, the P o w er LED will light up. As connections to the Switch’ s LEDs are pow ered on, each por t's cor respon- ding Link/Act LED will light up.
About Fast Ethernet History of Fast Ether net Standard Ethernet has been the most popular netw orking technology during this past decade, with a maximum data throughput of 10Mbps .
A netw ork without a s witch is called a shar ed netw ork because e very node on the netw ork competes for a fraction of the total bandwidth. In a shared netw ork, data packets are randoml y broadcasted to all stations until the y disco v er their intended destination.
Straight-Thr ough T wisted P air Wiring Cr ossed-Ov er T wisted P air W iring 11 EtherFast 10/100 Autosensing Switches T ypes of Ether net Cabling T wisted-pair cab ling comes in v arious grades, or categories. Category 5 is required for F ast Ether net, and is also the most reliable and most commonl y used type of cabling.
13 Customer Support F or help with the installation or operation of your EtherF ast 10/100 Autosensing Switch, contact Linksys Customer Support at one of the phone numbers or Internet addresses below . T echnical Support 800-326-7114 949-261-1288 Fa x 949-261-8868 Email support@linksys.
An important point after buying a device Linksys EZXS88W (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Linksys EZXS88W yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Linksys EZXS88W - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Linksys EZXS88W you will learn all the available features of the product, as well as information on its operation. The information that you get Linksys EZXS88W will certainly help you make a decision on the purchase.
If you already are a holder of Linksys EZXS88W, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Linksys EZXS88W.
However, one of the most important roles played by the user manual is to help in solving problems with Linksys EZXS88W. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Linksys EZXS88W along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
