EN
Linksys logo
Official user manual

Linksys Etherfast

57 pages·2.1 MB·Network Router·PDF·ENDEFRITNLJA
Linksys Etherfast
Table of Contents 13 sections Instant EtherFast ® Series · User Guide · UG-EF24G2M-011029NC JL · EtherFast ® Series Table of Contents · … ShowHide
Page 1 of the Linksys Etherfast user manual — User Guide
Page 1 · click to enlarge
Page 1
Use this guide to installLinksys EtherFast ® Managed 24-Port with Dual Gigabit Switch (EF24G2M)
Linksys Etherfast — Instant EtherFast ® Series diagram (page 1)
Fig. 1 · Instant EtherFast ® Series

Instant EtherFast ® Series

Linksys Etherfast — Instant EtherFast ® Series diagram (page 1)
Fig. 2 · Instant EtherFast ® Series

User Guide

Page 2 of the Linksys Etherfast user manual — UG-EF24G2M-011029NC JL
Page 2 · click to enlarge
Page 2

UG-EF24G2M-011029NC JL

  • Reorient or relocate the receiving antenna
  • Increase the separation between the equipment or devices
  • Connect the equipment to an outlet other than the receiver’s
  • Consult a dealer or an experienced radio/TV technician for assistance

FCC STATEMENT The EtherFast® Managed 24-Port with Dual Gigabit Switch has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radi- ate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guaran- tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Linksys P.O. Box 18558, Irvine, CA 92623.

Linksys makes no warranty or representation, expressed, implied, or statutory, with respect to its products or the contents or use of this documentation and all accompa- nying software, and specifically disclaims its quality, performance, merchantability, or fitness for any particular purpose. Linksys reserves the right to revise or update its products, software, or documentation without obligation to notify any individual or entity. Please direct all inquiries to:

IN NO EVENT SHALL LINKSYS’ LIABILITY EXCEED THE PRICE PAID FOR THE PROD- UCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAM- AGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFT- WARE, OR ITS DOCUMENTATION. LINKSYS DOES NOT ISSUE REFUNDS. WARRAN- TY DOES NOT COVER NATURAL DISASTERS OR ACTS OF NATURE.

LIMITED WARRANTY Linksys guarantees that every EtherFast® Managed 24-Port with Dual Gigabit Switch is free from physical defects in material and workmanship under normal use for FIVE years from the date of purchase. If the product proves defective during this warranty period, call Linksys Customer Support in order to obtain a Return Authorization Number. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALL- ING. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PUR- CHASE. When returning a product, mark the Return Authorization Number clearly on the outside of the package and include a copy of your original proof of purchase. All customers outside of the United States of America and Canada shall be held responsi- ble for shipping and handling charges.

COPYRIGHT & TRADEMARKS Copyright © 2001 Linksys, All Rights Reserved. EtherFast is a registered trademark of Linksys. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. All other trademarks and brand names are the property of their respective proprietors.

Page 3 of the Linksys Etherfast user manual — Introduction
Page 3 · click to enlarge
Page 3

Specifications 104 Environmental 104

Glossary 96 Upgrading Firmware via the Serial Port 96

Troubleshooting 93 Common Problems and Solutions 93

Configuring the Switch 12 Overview 12 Logging On to the Switch 12 Main Menu 13 System Information Menu 14 Management Setup Menu 17 Device Control Menu 30 Network Monitor Menu 65 System Restart Menu 91 Exit 92

Switch Management 8 Overview 8

Installing the Switch 6 Pre-Installation Considerations 6 Rack-Mounting the Switch 7 Powering on the Switch 7 Uplinking the Switch 7

Getting to Know the Switch 3 LEDs 3 The RJ-45 Ports 5 The Gigabit Ports 5 The Console Port 5

Introduction 1 Package Contents 2

EtherFast ® Series Table of Contents

Save money and time with this all-in-one managed solution for Gigabit connectiv- ity to your servers or Gigabit backbone.

The Managed 24-Port Switch’s “intelligent” Layer 3 switching and design provide maximum network control, regulating traffic and eliminating server bottlenecks. Integrate the Managed 24-Port Switch into your current Ethernet network, and your data traffic efficiency will improve several times over. Connect your worksta- tions to the managed 10/100 ports, and speed up access time for all your users in just one move. Connect your servers through the Gigabit ports for dedicated band- width of up to 1000Mbps—and you’ve maximized your network potential. Plus, configuration’s a snap using the Web management interface.

Migrate your network to Gigabit speed with the EtherFast® Managed 24-Port with Dual Gigabit Switch. Perfect for today’s network computing demands, this new Managed 24-Port Switch from Linksys delivers Layer 3 switching and blazing transfer speeds for your network applications with integrated Gigabit over cop- per connectivity.

The Linksys EtherFast® Managed 24-Port with Dual Gigabit Switch

Introduction

Contact Information 106 · Warranty Information 105 · Glossary 93

Page 4 of the Linksys Etherfast user manual — Getting to Know the Switch
Page 4 · click to enlarge
Page 4
  • One EtherFast ® Managed 24-Port with Dual Gigabit Switch
  • One Power Cord
  • Mounting Brackets (not shown)
  • One Serial/Console Cable (not shown)
  • User Guide
  • Registration Card (not shown)
Linksys Etherfast — Getting to Know the Switch diagram (page 4)
Fig. 3 · Getting to Know the Switch

ACT (Green) The LED will illuminate when the port is actively operating.

GIGABIT PER PORT (G1/G2) LNK (Green) The LED will illuminate when the port is successfully connected to a network.

Mode (Green) The LED will illuminate when the port is operating in full-duplex mode.

PER PORT LNK (Green) The LED will illuminate when the port is connected.

OverHeat (Green) The LED will illuminate when the switch is overheating.

Fan Failure (Green) The LED will illuminate when a fan has failed.

Console (Green) The LED will illuminate when the switch is being managed via the local console.

SNMP (Green) The LED will illuminate when the switch is being managed via SNMP.

Power (Green) The LED will illuminate when the switch is powered on.

Getting to Know the Switch

Linksys Etherfast — Getting to Know the Switch diagram (page 4)
Fig. 4 · Getting to Know the Switch

Package Contents · LEDs

Page 5 of the Linksys Etherfast user manual — Getting to Know the Switch
Page 5 · click to enlarge
Page 5

MODE COL (Amber) The LED will illuminate when collisions are detected. ACT (Amber) The LED will illuminate when there are active ports. FDX (Amber) The LED will illuminate when there are ports operating in full-duplex mode. 100M (Amber) The LED will illuminate when there are ports transmitting data at 100Mbps.

If your Switch is having problems with network connections, press the Reset button for five seconds. This clears up any jammed connections, and is simi- lar to pressing the Reset button on your PC to reboot it.

Linksys Etherfast — Getting to Know the Switch diagram (page 5)
Fig. 5 · Getting to Know the Switch

The EtherFast® Managed 24-Port with Dual Gigabit Switch is equipped with a serial port (located on the rear of the switch) that allows you to connect to a computer (for configuration purposes) using the provided serial cable.

The EtherFast® Managed 24-Port with Dual Gigabit Switch is equipped with two Gigabit ports. These ports provide links to high-speed network segments or individual workstations at speeds of up to 1000Mbps (Gigabit Ethernet). The two Gigabit ports require UTP Category 5e cable (or better).

Linksys Etherfast — Getting to Know the Switch diagram (page 5)
Fig. 6 · Getting to Know the Switch

To connect a device to a port, you will need to use a network cable. If you are using 100BaseTX devices you will need to use UTP Category 5 (or better) cable. The two Gigabit ports require UTP Category 5e cable (or better).

The EtherFast® Managed 24-Port with Dual Gigabit Switch is equipped with twenty-four 10/100 RJ-45 ports. These RJ-45 ports support network speeds of either 10-100Mbps in half-duplex mode, or 20-200Mbps in full-duplex mode. Auto-sensing technology enables each port to automatically detect the speed of the device connected to it (10Mbps or 100Mbps), and adjust its speed and duplex accordingly.

Show 4 more labels / short text on this page
The Reset Button · The Console Port · The Gigabit Ports · The RJ-45 Ports
Page 6 of the Linksys Etherfast user manual — Getting to Know the Switch
Page 6 · click to enlarge
Page 6
  • Do not stack free-standing Switches more than four units high.
  • To ensure adequate air flow around the Switch, be sure to provide a minimum of one inch (25mm) clearance.
  • Position the Switch away from water and moisture sources.
  • Keep cabling away from sources of electrical noise, power lines, and fluorescent lighting fixtures.

Before you choose a location for the Switch, observe the following guide- lines:

If you will be using the Switch in full-duplex mode, the maximum UTP cable length using Category 5e (or better) cable is 328 feet (100 meters).

As previously mentioned, the Switch provides full-duplex support for its RJ- 45 ports. Full-duplex operation allows data to be sent and received simultane- ously, doubling a port’s potential data throughput.

Rack-Mounting the Switch The EtherFast®Managed 24-Port with Dual Gigabit Switch can be used as a free-standing unit, or installed in any standard 19-inch rack. Use the following instructions to rack-mount the Switch: Before you begin, disconnect all cables from the Switch. 1. Place the Switch right side up, with the front panel facing you. 2. Position a mounting bracket over the screw holes on one side of the Switch. 3. Secure the mounting bracket by inserting three screws into the screw holes. Use a screwdriver to tighten the screws, ensuring that they are fastened firmly in place. 4. Repeat steps 2 and 3 to install the other mounting bracket on the opposite side of the Switch. 5. Insert the Switch into the 19-inch rack and secure it with suitable screws (not provided). Ensure that the ventilation holes are not obstructed. The rack-mount installation is complete. You can now re-connect the cables to the Switch. Powering on the Switch To power on the Switch, simply connect the AC power cord to the back of the Switch, and then plug the power cord into an electrical outlet. The Switch will boot up within approximately 30 seconds. Uplinking the Switch Any of the 26 ports on the EtherFast®Managed 24-Port with Dual Gigabit Switch can act as an uplink port, allowing you to uplink to other switches or hubs using a standard Ethernet connection. UTP Category 5e (or better) cable is recommended when using the Gigabit ports. To uplink the switch, connect one end of a network cable into the Switch, then connect the other end of the cable into the desired network device’s uplink port.Any of the 26 ports on the EtherFast®Managed 24-Port with Dual Gigabit Switch can act as an uplink port, allowing you to uplink to other switches or hubs using a standard Ethernet connection. UTP Category 5e (or better) cable is recommended when using the Gigabit ports. To uplink the switch, connect one end of a network cable into the Switch, then connect the other end of the cable into the desired network device’s uplink port. 7

To uplink the switch, connect one end of a network cable into the Switch, then connect the other end of the cable into the desired network device’s uplink port.

Any of the 26 ports on the EtherFast® Managed 24-Port with Dual Gigabit Switch can act as an uplink port, allowing you to uplink to other switches or hubs using a standard Ethernet connection. UTP Category 5e (or better) cable is recommended when using the Gigabit ports.

To power on the Switch, simply connect the AC power cord to the back of the Switch, and then plug the power cord into an electrical outlet. The Switch will boot up within approximately 30 seconds.

Powering on the Switch

5. Insert the Switch into the 19-inch rack and secure it with suitable screws (not provided). Ensure that the ventilation holes are not obstructed.
4. Repeat steps 2 and 3 to install the other mounting bracket on the opposite side of the Switch.
3. Secure the mounting bracket by inserting three screws into the screw holes. Use a screwdriver to tighten the screws, ensuring that they are fastened firmly in place.

The rack-mount installation is complete. You can now re-connect the cables to the Switch.

Positioning the Switch · Uplinking the Switch

Page 7 of the Linksys Etherfast user manual — Switch Management
Page 7 · click to enlarge
Page 7
1. Click the Start button. Select Accessories and then Communications . Hyperterminal should be one of the options listed in this menu. Select Hyperterminal .

The serial port settings need to be configured before connecting to the Switch. In order to change the settings of your port, run the Hyperterminal program. This program comes packaged with Windows, but it may not be installed on your computer. It should be located as is shown below (varies according to operating system). If it is not, consult your Windows documenta- tion for instructions on installing Hyperterminal.

You can manage the Switch locally by connecting the switch to a PC or work- station with terminal emulation software using the serial port.

  • Enable/disable any port
  • Set the communication mode for any port
  • Configure SNMP parameters
  • Add ports to network VLANs

The Linksys EtherFast® Managed 24-Port with Dual Gigabit Switch offers an easy-to-use, menu-driven configuration program. This program can be accessed by a console interface, a Web browser, a telnet connection, or SNMP/RMON. Using this configuration program, you can perform various switch configuration and management activities, including:

Switch Management

Linksys Etherfast — Switch Management diagram (page 7)
Fig. 7 · Switch Management
3. The following screen will appear. In the bottom drop down box labeled Connect using: , click the arrow and choose the COM port that the Switch will be connected to. In the example below, COM1 is the port selected. Click the OK button.
2. The following screen will appear. Enter a Name for this connection. In the example below, the name of the connection is EF24G2M. Click the OK button.
Linksys Etherfast — Switch Management diagram (page 7)
Fig. 8 · Switch Management
Linksys Etherfast — Switch Management diagram (page 7)
Fig. 9 · Switch Management

Overview · Local Console Management

Page 8 of the Linksys Etherfast user manual — Switch Management
Page 8 · click to enlarge
Page 8

Web management is available after the Switch has been configured with a valid IP address, subnet mask, and default gateway (for Layer 2 mode) via the console interface. Use a standard Web browser (Internet Explorer 4.0 or above, or Netscape Navigator 4.0 or above is suggested) from any computer attached to the network. The Switch has a default IP address of 192.168.1.254 and a default subnet address of 255.255.255.0.

4. When the following screen appears, make sure that the Switch’s serial port settings are as follows:

Click the OK button.

BAUD RATE19200 DATA BITS: 8 PARITY: None STOP BITS: 1 FLOW CONTROL: None
Linksys Etherfast — Switch Management diagram (page 8)
Fig. 10 · Switch Management

SNMP/RMON management is available after the Switch has been configured with a valid IP address, subnet mask, and default gateway (for Layer 2 mode) via the console interface. Manage the Switch from any network computer using network management software.

Telnet management is available after the Switch has been configured with a valid IP address, subnet mask, and default gateway (for Layer 2 mode) via the console interface. Use telnet from any computer attached to the network.

Web Management · SNMP/RMON Management · Telnet Management

Page 9 of the Linksys Etherfast user manual — Switch Management
Page 9 · click to enlarge
Page 9

When you select User Configuration from the Management Setup Menu (discussed later in this User Guide), you will be allowed to define a new administrator password.

Enter the default User Name (“admin”), and press Enter. Do not enter any- thing for the Password, and press Enter.

User NamePassword:

When logging on to the Switch, you will receive the following screen prompt:

Main Menu After you log on to the Switch, the Main Menu screen will appear. The Main Menu screen consists of a series of options. Each option leads you to the screen for that management setting. Highlighting any option selects it; pressing the Enter key takes you to that screen. To navigate through the Console Interface, use the Tab or arrow keys to move, the Enter key to select, and the Esc key to return to the previous selection. Scroll through choices using the spacebar. Options for the currently selected item are displayed in the highlighted area at the bottom of the interface screen. The text string in the top right corner of the screen shows if the Switch is operating as a Layer 2 switch or as a multilayer routing switch. • System Information Menu - Displays a basic description of the switch, including contact information and hardware and firmware versions. • Management Setup Menu - Adjust the communication parameters, ensuring a reliable connection. • Device Control Menu - Controls a broad range of functions, including port mode, port mirroring, port trunking, spanning tree, VLANs, IP subnets, multicast filtering, and routing protocols.After you log on to the Switch, the Main Menu screen will appear. The Main Menu screen consists of a series of options. Each option leads you to the screen for that management setting. Highlighting any option selects it; pressing the Enter key takes you to that screen. To navigate through the Console Interface, use the Tab or arrow keys to move, the Enter key to select, and the Esc key to return to the previous selection. Scroll through choices using the spacebar. Options for the currently selected item are displayed in the highlighted area at the bottom of the interface screen. The text string in the top right corner of the screen shows if the Switch is operating as a Layer 2 switch or as a multilayer routing switch. • System Information Menu - Displays a basic description of the switch, including contact information and hardware and firmware versions. • Management Setup Menu - Adjust the communication parameters, ensuring a reliable connection. • Device Control Menu - Controls a broad range of functions, including port mode, port mirroring, port trunking, spanning tree, VLANs, IP subnets, multicast filtering, and routing protocols. 13
Linksys Etherfast — Switch Management diagram (page 9)
Fig. 11 · Switch Management

The text string in the top right corner of the screen shows if the Switch is operating as a Layer 2 switch or as a multilayer routing switch.

To navigate through the Console Interface, use the Tab or arrow keys to move, the Enter key to select, and the Esc key to return to the previous selec- tion. Scroll through choices using the spacebar. Options for the currently selected item are displayed in the highlighted area at the bottom of the inter- face screen.

The Main Menu screen consists of a series of options. Each option leads you to the screen for that management setting. Highlighting any option selects it; pressing the Enter key takes you to that screen.

  • Device Control Menu - Controls a broad range of functions, including port mode, port mirroring, port trunking, spanning tree, VLANs, IP subnets, multicast filtering, and routing protocols.
  • Management Setup Menu - Adjust the communication parameters, ensuring a reliable connection.
  • System Information Menu - Displays a basic description of the switch, including contact information and hardware and firmware versions.
Linksys Etherfast — Switch Management diagram (page 9)
Fig. 12 · Switch Management
Page 10 of the Linksys Etherfast user manual — Switch Management
Page 10 · click to enlarge
Page 10

Select OK to return to the previous panel.

The System Information Menu displays a basic description of the Switch, including contact information and hardware and firmware versions.

  • Switch Information - Shows hardware and firmware version numbers, power status, and Gigabit port usage of the Switch.
  • System Information - Provides basic system descriptions, including contact information.
  • Exit - Exits the program and terminates communications with the Switch for the current session.
  • System Restart Menu - Resets the management agent.
  • Network Monitor Menu - Provides access to port statistics, RMON statistics, address tables, VLAN registration and forwarding information, multicast groups, and subnet addresses.
Linksys Etherfast — Switch Management diagram (page 10)
Fig. 13 · Switch Management

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

* The maximum string length is 99, but the screen only displays 45 charac- ters. You can use the arrow keys to browse the entire string.

The System Information screen displays descriptive information about the Switch or system.

  • System Location* - Specifies the area or location where the system resides.
  • System Contact* - Contact person for the system.
  • System Name* - Name assigned to the switch system.
  • System Up Time - Length of time the current management agent has been running. Note that the first value is in centiseconds.
  • System Object ID - MIB II object identifier for the Switch’s network management subsystem.
  • System Description - System hardware description.
Linksys Etherfast — Switch Management diagram (page 10)
Fig. 14 · Switch Management

System Information Menu · System Information

Page 11 of the Linksys Etherfast user manual — Switch Management
Page 11 · click to enlarge
Page 11

Select OK to return to the previous panel.

  • G2 Information - Speed of the second Gigabit port.
  • G1 Information - Speed of the first Gigabit port.
  • Fan Power Status - Shows if power to fan is active or inactive.
  • Power Status - Shows if power is active or inactive.
  • Number of Ports - Number of ports available on this Switch.
  • Serial Number - Serial number of the main board.
  • Firmware Version - System firmware version in ROM.
  • Hardware Version - Hardware version of the main board.
Management Setup Menu The Management Setup Menu screen allows you to adjust the communication parameters, ensuring a reliable connection. The new administrator password is set through this menu. The IP parameters for Web, telnet, or SNMP/RMON management are set here as well. • Network Configuration - Includes IP setup, ping facility, and HTTP setup for the on-board Web agent. • Serial Port Configuration - Sets communication parameters for the serial port, including baud rate, console time-out, and screen data refresh interval. • SNMP Configuration - Activates authentication failure traps and configures communities and trap managers. • User Configuration - Sets the user names and passwords for system access. • TFTP Download - Downloads new version of firmware to update your system. • Configuration File - Allows downloading of a configuration file. Select OK to return to the previous panel.The Management Setup Menu screen allows you to adjust the communication parameters, ensuring a reliable connection. The new administrator password is set through this menu. The IP parameters for Web, telnet, or SNMP/RMON management are set here as well. • Network Configuration - Includes IP setup, ping facility, and HTTP setup for the on-board Web agent. • Serial Port Configuration - Sets communication parameters for the serial port, including baud rate, console time-out, and screen data refresh interval. • SNMP Configuration - Activates authentication failure traps and configures communities and trap managers. • User Configuration - Sets the user names and passwords for system access. • TFTP Download - Downloads new version of firmware to update your system. • Configuration File - Allows downloading of a configuration file. Select OK to return to the previous panel. 17
Linksys Etherfast — Switch Management diagram (page 11)
Fig. 15 · Switch Management

Select OK to return to the previous panel.

  • Configuration File - Allows downloading of a configuration file.
  • TFTP Download - Downloads new version of firmware to update your system.
  • User Configuration - Sets the user names and passwords for system access.
  • SNMP Configuration - Activates authentication failure traps and configures communities and trap managers.
  • Serial Port Configuration - Sets communication parameters for the serial port, including baud rate, console time-out, and screen data refresh interval.
  • Network Configuration - Includes IP setup, ping facility, and HTTP setup for the on-board Web agent.
Linksys Etherfast — Switch Management diagram (page 11)
Fig. 16 · Switch Management
Page 12 of the Linksys Etherfast user manual — Switch Management
Page 12 · click to enlarge
Page 12

Select OK to return to the previous panel.

* This menu does not appear if the Switch is set to multilayer mode. In this case, you need to configure an IP interface for each VLAN that needs to con- nect to any device outside of its own VLAN group.

The Network Configuration menu allows you to set the Switch’s IP address, configure the IP parameters, or enable the on-board Web management.

  • HTTP Configuration - Allows the admin to enable or disable the Web administration.
  • IP Connectivity Test (Ping) - Tests IP connectivity to a specified device.
  • IP Configuration* - Sets the bootup option or configure the Switch’s IP parameters.
Linksys Etherfast — Switch Management diagram (page 12)
Fig. 17 · Switch Management

EtherFast® Managed 24-Port with Dual Gigabit Switch EtherFast® Series

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

  • IP State - Specifics whether IP functionality is enabled via manual configuration (default setting), or set by Boot Protocol (BOOTP).
  • Gateway IP - Gateway used to pass trap messages from the system to the management station. Note: The gateway must be defined (when operating at Layer 2) if the management station is located in a different IP segment.
  • Subnet Mask - Subnet mask of the Switch. This mask identifies the host address bits used for routing to specific subnets.
  • IP Address - IP address of the Switch you are managing. The system supports SNMP over UDP/IP transport protocol. In this environment, all systems on the Internet, such as network interconnection devices, must have an IP address.
  • Interface Type - Indicates IP over Ethernet.

The IP Configuration menu allows you to configure the IP parameters. (Only displayed in Layer 2 mode)

Linksys Etherfast — Switch Management diagram (page 12)
Fig. 18 · Switch Management

Network Configuration · IP Configuration

Page 13 of the Linksys Etherfast user manual — Switch Management
Page 13 · click to enlarge
Page 13

Select Start to begin the test. Select Cancel to cancel the test.

  • Success/Failure - The number of times the specified site has responded— or not—to a ping request.
  • Test Times - The number of ICMP echo requests to send to the specified site. Range varies from 1 to 1000.
  • IP Address - IP address of the device you want to ping.

The IP Connectivity Test is used to see if another site or node on the net- work can be reached.

IP Connectivity Test (Ping)

Linksys Etherfast — Switch Management diagram (page 13)
Fig. 19 · Switch Management

EtherFast® Managed 24-Port with Dual Gigabit Switch EtherFast® Series

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

The HTTP Configuration screen allows you to enable or disable Web man- agement.

Linksys Etherfast — Switch Management diagram (page 13)
Fig. 20 · Switch Management

HTTP Configuration

Page 14 of the Linksys Etherfast user manual — Switch Management
Page 14 · click to enlarge
Page 14

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

The Serial Port Configuration screen allows you to access the communication parameters for the Switch’s serial port.

  • Auto Refresh - Sets the interval before a console session will auto refresh the console information, such as Spanning Tree Information, Port Configuration, Port Statistics, and RMON Statistics. Default is 1 second. The range is 0, or 5 to 255 seconds, where 0 indicates disabled.
  • Time-Out - If no input is received from the attached device after this interval, the current session is automatically closed. Default is 10 minutes. The range is 0 to 100 minutes, where 0 indicates disabled.
  • Parity - Sets the parity of the RS-232 port. Default is None. Options are none, odd, and even.
  • Stop Bits - Sets the stop bits of the RS-232 port. Options are 1 and 2.
  • Data Bits - Sets the data bits of the RS-232 port. Options are 7 and 8.
  • Baud Rate - The rate at which data is sent between devices. Default is 19200. Options are 9600, 19200, and 38400 baud.
Linksys Etherfast — Switch Management diagram (page 14)
Fig. 21 · Switch Management

EtherFast® Managed 24-Port with Dual Gigabit Switch EtherFast® Series

Select OK to return to the previous panel.

The SNMP Configuration screen displays parameters for the Simple Network Management Protocol (SNMP).

  • IP Trap Managers - Specifies management stations that will receive authentication failure messages or other trap messages from the Switch.
  • SNMP Communities - Assigns SNMP access based on specified strings.
  • Send Authentication Fail Traps - Issue a trap message to specified IP trap managers whenever authentication of an SNMP request fails. Default is enabled.
Linksys Etherfast — Switch Management diagram (page 14)
Fig. 22 · Switch Management

Serial Port Configuration · SNMP Configuration

Page 15 of the Linksys Etherfast user manual — Switch Management
Page 15 · click to enlarge
Page 15

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

  • Status - Sets administrative status of entry to enabled or disabled.
  • Access - Management access is restricted to Read Only or Read/Write.
  • Community Name - A community entry authorized for management access. Maximum string length is 19 characters.

The SNMP Communities screen allows you to configure the community strings authorized for management access. Up to five community names may be entered.

Linksys Etherfast — Switch Management diagram (page 15)
Fig. 23 · Switch Management

EtherFast® Managed 24-Port with Dual Gigabit Switch EtherFast® Series

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

  • Community Name - A community specified for trap management access.
  • IP Address - IP address of the trap manager.

The IP Trap Managers screen specifies management stations that will receive authentication failure messages or other trap messages from the Switch. Up to five trap managers may be entered.

Linksys Etherfast — Switch Management diagram (page 15)
Fig. 24 · Switch Management

SNMP Communities · IP Trap Managers

Page 16 of the Linksys Etherfast user manual — Switch Management
Page 16 · click to enlarge
Page 16

Select Add to add a user. Select OK to return to the previous panel.

The User Configuration screen to restrict management access based on speci- fied user names and passwords. There are two user types, Administrator and Guest. Only the Administrator has write access for parameters governing the SNMP agent.

  • HTTP - Authorizes management via HTTP, e.g., a Web browser.
  • Telnet - Authorizes management via a telnet connection.
  • Console - Authorizes management via the console.
  • Access Right - ADMIN: Read/Write for all screens. GUEST: Read Only for all screens.
  • User Name - Specifies user authorized management access to the Switch via the console, telnet, or the Web.
Linksys Etherfast — Switch Management diagram (page 16)
Fig. 25 · Switch Management

Select OK to confirm the changes. Select Cancel to cancel any changes.

  • HTTP Access - Authorizes management via HTTP, e.g., a Web browser.
  • Telnet Access - Authorizes management via a telnet connection.
  • Console Access - Authorizes management via the console.
  • Access Right - ADMIN: Read/Write for all screens. GUEST: Read Only for all screens.
  • Password - Sets up the password for the new user.
  • User Name - Specifies user authorized management access to the Switch via the console, telnet, or the Web.

The Add User screen allows you to add a user.

Linksys Etherfast — Switch Management diagram (page 16)
Fig. 26 · Switch Management

User Configuration · Add User

Page 17 of the Linksys Etherfast user manual — Switch Management
Page 17 · click to enlarge
Page 17

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

The TFTP Download screen lets you load software updates to permanent flash ROM in the Switch. After downloading the new software, the agent will automatically restart itself.

  • Download Option - You may choose either Runtime Code or Post Code .
  • Download Filename - The binary file to download.
  • Download Server IP - IP address of a TFTP server.
Linksys Etherfast — Switch Management diagram (page 17)
Fig. 27 · Switch Management

Select Start to begin the download. Select Cancel to cancel the download.

The Configuration File screen allows you to load a configuration file on any Switch on the network.

  • Operation - Gives you the choice of downloading the configuration file from your Switch.
  • Station IP - IP address of the Switch you want the configuration file to be sent to.
Linksys Etherfast — Switch Management diagram (page 17)
Fig. 28 · Switch Management

Upload to switch - Uploads a configuration file to the Switch from the client PC.

Download from switch - Downloads the current switch configura- tion to a file on the client PC.

TFTP Download · Configuration File

Page 18 of the Linksys Etherfast user manual — Switch Management
Page 18 · click to enlarge
Page 18

The Device Control Menu is used to control a broad range of functions, including port mode, port mirroring, port trunking, Spanning Tree, VLANs, IP subnets, multicast filtering, and routing protocols.

  • Security Menu - Configures security settings here.
  • IP Menu - Configures the subnets for each VLAN group, global configuration for unicast and multicast routing protocols, and IGMP snooping. (Only displayed for multilayer mode)
  • VLAN Menu - Configures VLAN settings for specific ports, and defines the port membership for VLAN groups.
  • Bridge Menu - Configures the Spanning Tree Protocol for the bridge or for specific ports, GMRP and GVRP for automatic registration of multicast and VLAN groups, traffic class priority threshold, and address aging time.
  • Layer 2 Menu - Configures port communication mode, mirror ports, and port trunking.
  • System Mode - Sets the Switch to operate as a Layer 2 switch or as a multilayer routing switch.
Linksys Etherfast — Switch Management diagram (page 18)
Fig. 29 · Switch Management

Select OK to return to the previous panel.

  • IGMP Snooping Configuration - Configures IGMP multicast filtering. (Only displayed for Layer 2 mode. When the Switch is in multilayer mode, IGMP Snooping Configuration is available through the IP Menu.)
Linksys Etherfast — Switch Management diagram (page 18)
Fig. 30 · Switch Management

Device Control Menu

Page 19 of the Linksys Etherfast user manual — Switch Management
Page 19 · click to enlarge
Page 19

Select OK to return to the previous panel.

The System Mode screen lets you set the Switch to operate as a Layer 2 switch or as a multilayer routing switch. As a Layer 2 switch, the Switch makes all filtering and forwarding decisions based strictly on MAC address- es. As a multilayer routing switch, it switches packets for all non-IP protocols based on MAC addresses, and routes all IP packets based on the specified routing protocol.

  • Multilayer - Switching based on MAC addresses will be used for all non-IP protocol traffic, and routing will be used for all IP protocol traffic.
  • Layer 2 - Filtering and forwarding decisions will be based on MAC addresses for all protocol traffic.
Linksys Etherfast — Switch Management diagram (page 19)
Fig. 31 · Switch Management

Select OK to return to the previous panel.

The Layer 2 Menu contains options for port configuration, port mirroring, and port trunking.

  • Static Multicast Address Configuration - Used to manually configure host MAC addresses in the multicast table.
  • Static Unicast Address Configuration - Used to manually configure host MAC addresses in the unicast table.
  • Port Trunking Configuration - Specifies ports to group into aggregate trunks.
  • Mirror Port Configuration - Sets the source and target ports for mirroring.
  • Port Configuration - Enables any port, enables/disables flow control, and sets communication mode to auto-negotiation, full duplex, or half duplex.
Linksys Etherfast — Switch Management diagram (page 19)
Fig. 32 · Switch Management

System Mode · Layer 2 Menu

Page 20 of the Linksys Etherfast user manual — Switch Management
Page 20 · click to enlarge
Page 20
  • Flow Control - Used to enable or disable flow control. Flow control can eliminate frame loss by “blocking” traffic from end stations or segments
  • Current Type - Indicates the current speed and duplex mode.
  • Default Type - If auto-negotiation is disabled, the port will be set to the indicated speed and duplex mode.
  • Auto Negotiate - Enables or disables auto-negotiation for port speed, duplex mode, and flow control.
  • Admin Status - Allows you to disable a port due to abnormal behavior (e.g., excessive collisions), and then re-enable it after the problem has been resolved.
  • Link Status - Indicates if the port has a valid connection to an external device.

The Port Configuration screen lets you display or set communication parameters for any port or module on the Switch, including administrative status, auto-negotiation, default communication speed and duplex mode, as well as flow control in use.

Linksys Etherfast — Switch Management diagram (page 20)
Fig. 33 · Switch Management

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes. Select Prev Page to view the previous page. Select Next Page to view the next page.

  • Mirrored Ports (Tx/Rx) - The port whose transmitted or received traffic will be mirrored. Press Add to specify mirrored ports.
  • Enable Port Mirror - Enables or disables the mirror function.

The Mirror Port Configuration screen allows you to mirror traffic from any source port to a target port for real-time analysis. You can then attach a logic analyzer or RMON probe to the target port and study the traffic crossing the source port in a completely unobtrusive manner. When mir- roring port traffic, the target port must be included in the same VLAN as the source port.

  • Jack Type - Shows the jack type for each port. Ports 1-26 are RJ-45.

connected directly to the Switch when its buffers fill. When enabled, back pressure is used for half duplex and IEEE 802.3x for full duplex.

Linksys Etherfast — Switch Management diagram (page 20)
Fig. 34 · Switch Management

Port Configuration · Mirror Port Configuration

Page 21 of the Linksys Etherfast user manual — Switch Management
Page 21 · click to enlarge
Page 21

Select OK to return to the previous panel. Select Add to add a trunk.

Select Apply to make changes. Select OK to return to the previous panel. Select Add to add a port.

  • Port Number - The ports assigned to each trunk.
  • Port Count - Trunks can contain 2, 4, or 8 ports.
  • Index - The trunk identifier.

Ports can be combined into an aggregate link to increase the bandwidth of a network connection or ensure fault recovery. You can configure trunks between any two switches. The RJ-45 ports on this Switch can be grouped into a trunk consisting of two, four, or eight ports, creating an aggregate bandwidth up to 400, 800, or 1600Mbps when operating at full duplex.

  • Monitor Port - The port that will duplicate the transmitted or received traffic appearing on the mirrored port.
Linksys Etherfast — Switch Management diagram (page 21)
Fig. 35 · Switch Management

To assign a destination MAC address to one or more ports, use Add. To delete or modify an address, highlight it with the cursor and press Enter. Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

  • Port - The switch port the host device is attached to.
  • Address - The MAC address of a host device attached to this Switch.

The Static Unicast Address Table can be used to assign the MAC address for a host device to a specific port on this Switch. Static unicast addresses are never aged out, and cannot be learned on another port.

Static Unicast Address Configuration

Linksys Etherfast — Switch Management diagram (page 21)
Fig. 36 · Switch Management

Port Trunking Configuration

Page 22 of the Linksys Etherfast user manual — Switch Management
Page 22 · click to enlarge
Page 22

Select OK to confirm the changes. Select Cancel to cancel any changes.

Linksys Etherfast — Switch Management diagram (page 22)
Fig. 37 · Switch Management
  • Port - The switch port the host device is attached to.
  • Address - The MAC address of a host device attached to this Switch.

The Add Static Address Entry screen allows you to add static addresses for unicasting.

Add Static Address Entry

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

  • Port - The ports to which this multicast traffic can be forwarded. Read the numbers vertically; they range from 1-26. For each port number, there are two choices:
  • Address - The destination MAC address for a multicast service.
  • VLAN - The VLAN corresponding to this multicast service.

The Static Multicast Address Table can be used to assign a destination MAC address (and the corresponding ports) to the VLAN group used for a specific multicast service. Static multicast addresses are never aged out, and traffic with these addresses can only be forwarded to ports specified in this table.

Static Multicast Address Configuration

Linksys Etherfast — Switch Management diagram (page 22)
Fig. 38 · Switch Management

If there is no letter “M,” then there is no access to messages trans mitted by that particular port.

If the letter “M” is present, it indicates that the VLAN has access to messages transmitted by that particular port.

Page 23 of the Linksys Etherfast user manual — Switch Management
Page 23 · click to enlarge
Page 23

Select OK to confirm the changes. Select Cancel to cancel any changes.

  • Port - The ports to which this multicast traffic can be forwarded.
  • Address - The destination MAC address for a multicast service.
  • VLAN - The VLAN corresponding to this multicast service.

Read the numbers vertically; they range from 1-26. For each port number, there are two choices: “M” or nothing. Use the spacebar to scroll through the choices.

Linksys Etherfast — Switch Management diagram (page 23)
Fig. 39 · Switch Management

Select a blank space to indicate that there is no access to messages transmitted by that particular port.

Select the letter “M” to indicate that the VLAN has access to mes- sages transmitted by that particular port.

The Add Static Address Entry screen allows you to add static addresses for multicasting.

Add Multicast Address Entry

Select OK to return to the previous panel.

The Bridge Menu is used to configure settings for the Spanning Tree Algorithm, as well as the global bridge settings for GMRP (GARP Multicast Registration Protocol) and GVRP (GARP VLAN Registration Protocol), traf- fic classes priority threshold, and address aging time.

  • Spanning Tree Port Configuration - Contains STA settings for individual ports, including port priority, path cost, and fast forwarding.
  • Bridge Configuration - Contains global bridge settings for STA (including bridge priority, hello time, forward delay, maximum message age), GMRP, GVRP, traffic class priority threshold, and address aging time.
Linksys Etherfast — Switch Management diagram (page 23)
Fig. 40 · Switch Management

Bridge Menu

Page 24 of the Linksys Etherfast user manual — Switch Management
Page 24 · click to enlarge
Page 24
  • GMRP - GMRP allows network devices to register endstations with multicast groups.
  • Max Age - The maximum time (in seconds) a device can wait without receiving a configuration message before attempting to reconfigure.
  • Forward Delay - The maximum time (in seconds the root device will wait before changing states.
  • Hello Time - Time interval (in seconds) at which the root device transmits a configuration message.
  • Bridge Priority - Bridge priority is used in selecting the root device, root port, and designated port. The device with the highest priority becomes the STA root device. However, if all devices have the same priority, the device with the lowest MAC address will then become the root device. Enter a value from 0-65535. The lower the numeric value, the higher the priority.
  • Spanning Tree - Enable this parameter to participate in a STA compliant network.

The Bridge Configuration screen allows you to configure global bridge settings.

Linksys Etherfast — Switch Management diagram (page 24)
Fig. 41 · Switch Management

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

  • Priority - Defines the priority for the use of a port in the STA algorithm. If the path cost for all ports on a switch are the same, the port with the highest priority (that is, lowest value) will be configured as an active link in the Spanning Tree. When more than one port is assigned the highest
  • Type - Shows port type as 100TX for 10Base-T/100Base-TX, or 1000T for 1000Base-T.

The Spanning Tree Port Configuration allows you to configure spanning tree port settings.

Spanning Tree Port Configuration

  • Aging Time - Time-out period in seconds for aging out dynamically learned forwarding information. Range varies from 10-415 seconds.
  • Priority Threshold - This Switch supports Quality of Service (QoS) by using two priority queues, with Weighted Fair Queuing for each port.
  • GVRP - GVRP defines a way for switches to exchange VLAN information in order to register VLAN members on ports across the network. This function should be enabled to permit automatic VLAN registration, and to support VLANs which extend beyond the local switch.
Linksys Etherfast — Switch Management diagram (page 24)
Fig. 42 · Switch Management

Bridge Configuration

Page 25 of the Linksys Etherfast user manual — Switch Management
Page 25 · click to enlarge
Page 25

The VLAN Menu is used to assign any port on the Switch to any of up to 256 VLAN groups. By using IEEE 802.1Q compliant VLANs, you can organize any group of network nodes into separate broadcast domains, confining broadcast traffic to the originating group. This also provides a more secure and cleaner network environment.

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes. Select Prev Page to view the previous page. Select Next Page to view the next page.

  • VLAN Port Configuration - Configure GARP, the default VLAN identifier, default port priority, VLAN tagging on the attached link, GVRP and
  • Fast Forwarding - This parameter is used to enable/disable the Fast Spanning Tree mode for the selected port.
  • Cost - This parameter is used by the STA algorithm to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (This takes precedence over port priority.)

priority, the port with the lowest numeric identifier will be enabled. The range is 0-255.

Linksys Etherfast — Switch Management diagram (page 25)
Fig. 43 · Switch Management

Select OK to return to the previous panel.

  • VLAN Table Configuration - Use this screen to create a new VLAN or modify the settings for an existing VLAN.
  • Leave Time - The interval (centiseconds) a port waits before leaving a group. This time should be set to more than twice the Join Time. This
  • Join Time - The interval (centiseconds) between transmitting requests/queries to participate in a group.

GARP Group Address Registration Protocol is used by GVRP and GMRP to reg- ister or deregister client attributes for client services within a bridged LAN.

The VLAN Port Configuration screen allows you to configure GARP, the default VLAN identifier, default port priority, VLAN tagging on the attached link, GVRP and GMRP status, and filtering of incoming frames for VLAN groups a specific port does not belong to.

GMRP status, and filtering of incoming frames for VLAN groups a spe- cific port does not belong to.

Linksys Etherfast — Switch Management diagram (page 25)
Fig. 44 · Switch Management

VLAN Menu · VLAN Port Configuration

Page 26 of the Linksys Etherfast user manual — Switch Management
Page 26 · click to enlarge
Page 26

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes. Select Prev Port to view the previous port. Select Next Port to view the next port. To display a specific port, set the port number in the Page field and then press Apply.

  • Ingress Filtering - If enabled, incoming frames for VLANs that do not include this ingress port in their member set will be discarded at the ingress port.
  • GMRP - Enables or disables GMRP for this port. When enabled, this port will allow endstations to register with multicast groups. Note: GMRP must be enabled for the Switch before this setting can take effect.
  • GVRP - Enables or disables GVRP for this port. When disabled, any GVRP packets received on this port will be discarded and no GVRP registrations will be propagated from other ports. Note: GMVP must be enabled for the Switch before this setting can take effect.
  • VLAN Tagging - Indicates whether or not VLAN tags will be included on frames passing through this port.
  • Port Default Priority - Sets the default ingress priority to any value beneath the priority threshold to specify the low priority queue, or to any value equal to or above this threshold to specify the high priority queue.
  • Port VID - The VLAN ID assigned to untagged frames received on this port.

VLAN and Priority These fields set the default values for VLANs, port priority, GVRP, and GMRP.

  • Leave All Time - The interval (centiseconds) between sending out a Leave All query message for group participants and the port leaving the group. This interval should be considerably larger than the Leave Time to minimize the amount of traffic generated by nodes rejoining the group.

ensures that after a Leave or Leave All message has been issued, the applicants can re-join before the port actually leaves the group.

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply. Select Add to add a VLAN.

  • Port - Port entries may be marked as:
  • VLAN - The ID for the VLAN currently displayed. The range is 1-2048.

The VLAN Table Configuration screen is used to create a new VLAN or modify the settings for an existing VLAN.

Linksys Etherfast — Switch Management diagram (page 26)
Fig. 45 · Switch Management

– (Normal) Uses GVRP to determine port membership. S (Static) Adds port as a static entry. GVRP protocol is disabled. R (Registration Fixed) Adds port as a static entry. GVRP protocol messages are still forwarded through this port. X (Forbidden) Disables GVRP for this VLAN on the specified port.

VLAN Table Configuration

Page 27 of the Linksys Etherfast user manual — Switch Management
Page 27 · click to enlarge
Page 27

Select OK to return to the previous panel.

The IP Menu is used to configure the IP subnets for each VLAN on your Switch, the unicast and multicast routing protocols, and IGMP. This menu is only available for a Switch in multilayer mode.

  • Default Route - Defines the router to which this Switch will forward all traffic for unknown networks.
  • Static Route - Configures a static route.
  • Static ARP Configuration - Specifies the static Address Resolution Protocol.
  • Protocol Configuration - Enables the unicast and multicast routing protocols globally for this Switch.
  • Subnet Configuration - Specifies the IP interface for VLANs configured on this Switch, including the subnet address and routing protocols.
Linksys Etherfast — Switch Management diagram (page 27)
Fig. 46 · Switch Management

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply. Select Add to add an IP interface.

  • DVMRP - Distance-Vector Multicast Routing Protocol.
  • RIP - Routing Information Protocol for unicast routing.
  • VLAN - The VLAN associated with this IP interface.
  • Subnet Mask - A template that identifies the address bits in the host address used for routing to specific subnets. Each bit that corresponds to a “1” is part of the network/subnet number, and each bit that corresponds to “0” is part of the host number.
  • IP Address - The IP address associated with the specified VLAN interface. By convention, the last three digits should be set to “254” to readily distinguish this device as a router port.

The Subnet Configuration screen allows you to specify an IP interface for any VLAN configured on this Switch that needs to communicate with a device outside of its own group (that is, another network segment).

Linksys Etherfast — Switch Management diagram (page 27)
Fig. 47 · Switch Management

IP Menu · Subnet Configuration

Page 28 of the Linksys Etherfast user manual — Switch Management
Page 28 · click to enlarge
Page 28

Select OK to confirm the changes. Select Cancel to cancel any changes.

Linksys Etherfast — Switch Management diagram (page 28)
Fig. 48 · Switch Management
  • DVMRP - Distance-Vector Multicast Routing Protocol.
  • RIP - Routing Information Protocol for unicast routing.
  • Proxy ARP - Proxy Address Resolution Protocol.
  • Subnet Mask - A template that identifies the address bits in the host address used for routing to specific subnets.
  • IP Address - The IP address associated with the specified VLAN interface.
  • Select - Use this option to create or modify a VLAN.
  • VLAN - The VLAN associated with this IP interface.

The Add Subnet screen allows you to add an IP interface.

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

  • DHCP Relay - Dynamic Host Configuration Protocol relay. Select Advanced for additional configuration. .
  • IGMP Snooping - IGMP multicast filtering. Select Advanced for addtional configuration. (See page 64.)
  • DVMRP - Distance-Vector Multicast Routing Protocol.
  • RIP - Routing Information Protocol for unicast routing. Select Advanced for additional configuration.
  • Proxy ARP - Proxy Address Resolution Protocol.
  • ARP - Address Resolution Protocol. Select Advanced for additional configuration.

The Protocol Configuration screen is used to globally enable or disable unicast or multicast routing protocols for the Switch.

Linksys Etherfast — Switch Management diagram (page 28)
Fig. 49 · Switch Management

Add Subnet · Protocol Configuration

Page 29 of the Linksys Etherfast user manual — Switch Management
Page 29 · click to enlarge
Page 29

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

Linksys Etherfast — Switch Management diagram (page 29)
Fig. 50 · Switch Management
  • ARP Timeout - Duration of timeout (in minutes).

The ARP Configuration screen allows you to specify the timeout duration.

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

  • Ignore Host Route - Does not use host routes.
  • Static Route Advertisement - Static route messages.
  • Default Route Advertisement - Default route messages.
  • RIP Update Time - Duration of timeout (in seconds).
Linksys Etherfast — Switch Management diagram (page 29)
Fig. 51 · Switch Management

The RIP Configuration screen allows you to specify the how routers exchange routing table information.

ARP Configuration · RIP Configuration

Page 30 of the Linksys Etherfast user manual — Switch Management
Page 30 · click to enlarge
Page 30

Select OK to return to the previous panel. Select Cancel to cancel any changes.

Select OK to return to the previous panel. Select Add to add another entry.

  • IP Address - IP address of server.

The Add BOOTP Relay Server screen allows you to add an entry.

Add BOOTP Relay Server

  • Index Server Address - Used to define any preferred DHCP servers or the outbound subnetwork for relaying a DHCP request broadcast. (Up to five entries are permitted.)

The BOOTP Relay Database Configuration screen allows you to specify the IP address for a BOOTP relay server.

BOOTP Relay Database Configuration

Linksys Etherfast — Switch Management diagram (page 30)
Fig. 52 · Switch Management
Linksys Etherfast — Switch Management diagram (page 30)
Fig. 53 · Switch Management

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply. Select Add to add a static ARP entry.

  • Interface - The index number of the IP interface that will use this static ARP entry. (Port “0” refers to the CPU.)
  • MAC Address - MAC address statically mapped to the corresponding IP address.
  • IP Address - IP address statically mapped to a physical MAC address.

The Static ARP Table screen is used to specify the static Address Resolution Protocol.

Linksys Etherfast — Switch Management diagram (page 30)
Fig. 54 · Switch Management

Static ARP Table

Page 31 of the Linksys Etherfast user manual — Switch Management
Page 31 · click to enlarge
Page 31

Select OK to return to the previous panel. Select Cancel to cancel any changes.

Linksys Etherfast — Switch Management diagram (page 31)
Fig. 55 · Switch Management
  • Interface - The index number of the IP interface that will use this static ARP entry. (Port “0” refers to the CPU.)
  • MAC Address - MAC address statically mapped to the corresponding IP address.
  • IP Address - IP address statically mapped to a physical MAC address.

The Add Static ARP Entry screen is used to add a static ARP entry.

Add Static ARP Entry

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply. Select Add to add a routing entry. 57

  • Type - The IP route type for the destination network.
  • Next Hop - The IP address of the router at the next hop.
  • VLAN - The VLAN within which the gateway or destination address resides.
  • Destination Mask - The subnet mask that specifies the bits to match. A routing entry will be used for a packet if the bits in the address set by the destination mask match the destination network.
  • Destination Network - A destination network, subnet, or host.

The Static Route Table screen is used to configure a static route.

Linksys Etherfast — Switch Management diagram (page 31)
Fig. 56 · Switch Management

Direct - A directly connected subnetwork Indirect - A remote IP subnetwork or host address Myself - A switch IP address on a specific IP subnetwork Bcast - A subnetwork broadcast address Mcast - An IP multicast address Invalid - An illegal IP address to be filtered

Static Route Table

Page 32 of the Linksys Etherfast user manual — Switch Management
Page 32 · click to enlarge
Page 32

Select OK to return to the previous panel. Select Cancel to cancel any changes.

Linksys Etherfast — Switch Management diagram (page 32)
Fig. 57 · Switch Management
  • Routing Metric - Indicate the number of hopes to the destination network.
  • Interface - Identification number for interface of static ARP entry.
  • MAC Address - MAC address of static ARP entry.
  • IP Address - IP address of static ARP entry.

The Add Routing Entry screen is used to add a routing entry.

Select Delete to delete the route. Select OK to return to the previous panel. Select Cancel to cancel any changes.

  • Metric - The number of hops required to reach the default router.
  • Next Hop Address - The IP address of the default router.
  • VLAN - The VLAN which has the IP interface to the default router.

The Default Route Menu screen is used to define a route to which this Switch will forward all traffic for unknown networks.

Linksys Etherfast — Switch Management diagram (page 32)
Fig. 58 · Switch Management

Add Routing Entry · Default Route Menu

Page 33 of the Linksys Etherfast user manual — Switch Management
Page 33 · click to enlarge
Page 33

Select OK to return to the previous panel.

The Security Menu is used to configure security options.

  • IP Filtering Configuration - Configures IP filtering settings. (Only available when the Switch is in multilayer mode)
  • Security Mode - Enable/disable the Learning mode here.
  • MAC Filtering Configuration - Security filtering can be used to drop all the traffic from a host device based on a specified MAC address. Traffic with either a source or destination address listed in the MAC Filtering Configuration table will be filtered.
Linksys Etherfast — Switch Management diagram (page 33)
Fig. 59 · Switch Management

To add a MAC address, use Add. To delete an address, highlight it with the cursor and press Enter. Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

The MAC Filtering Configuration screen allows you to filter out specified MAC addresses. Any node that presents a security risk or is malfunction- ing can be filtered from this Switch. Security filtering can be used to drop all the traffic from a host device based on a specified MAC address.

Linksys Etherfast — Switch Management diagram (page 33)
Fig. 60 · Switch Management

Security Menu · MAC Filtering Configuration

Page 34 of the Linksys Etherfast user manual — Switch Management
Page 34 · click to enlarge
Page 34

Select Apply to make a change. Select OK to return to the previous panel. Select Cancel to cancel any change.

Select OK to confirm the changes. Select Cancel to cancel any changes.

  • Learning Function - Enables/disables Learning function for security filtering.

The Security Mode menu is used to enable/disable the Learning function.

  • MAC Address - The MAC address of a host device attached to this Switch.

The Add MAC Address Filter screen allows you to add MAC addresses.

Add MAC Address Filter

Linksys Etherfast — Switch Management diagram (page 34)
Fig. 61 · Switch Management
Linksys Etherfast — Switch Management diagram (page 34)
Fig. 62 · Switch Management

Select OK to confirm the changes. Select Cancel to cancel any changes.

To add an IP address, use Add. To delete an address, highlight it with the cur- sor and press Enter. Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

  • IP Address - The IP address to be filtered.

Security filtering can be used to drop all the traffic from a specified IP address. (Only available when the Switch is in multilayer mode)

IP Security Filtering Configuration

The Add IP Address Filter screen allows you to add IP addresses.

Add IP Address Filter

Linksys Etherfast — Switch Management diagram (page 34)
Fig. 63 · Switch Management
Linksys Etherfast — Switch Management diagram (page 34)
Fig. 64 · Switch Management

Security Mode

Page 35 of the Linksys Etherfast user manual — Switch Management
Page 35 · click to enlarge
Page 35

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes.

The IGMP Snooping Configuration allows you to set up IGMP snooping. IGMP snooping is used to monitor for any attached hosts who want to receive a specific multicast service. It looks up the IP Multicast Group used for this service and adds any port that received a similar request to that group.

* These options are not available when the Switch is in multilayer mode.

  • Act as IGMP Querier* - If enabled, the Switch will query other devices in regards to IGMP.
  • IGMP Group Timeout - The time between last spotting an IGMP Report message for an IP multicast address on a specific port and the Switch removing that entry from its list. The range is 3-5 minutes.
  • IGMP Router Timeout - A switch port that stops receiving multicast protocol packets for this interval will be removed from the IGMP forwarding list. The range is 3-5 minutes.
  • IGMP Status* - If enabled, the Switch will monitor network traffic to determine which hosts want to receive multicast traffic.
Linksys Etherfast — Switch Management diagram (page 35)
Fig. 65 · Switch Management

The Network Monitor Menu provides access to port statistics, RMON statis- tics, address tables, VLAN registration and forwarding information, multicast groups, and subnet addresses.

  • VLAN Menu - Includes learned ports in the VLAN Dynamic Registration Information table, and the ports that are currently forwarding VLAN traffic in the VLAN Forwarding Information table.
  • Bridge Menu - The Bridge menu displays settings for the Spanning Tree Algorithm, as well as the global bridge settings for GMRP (GARP Multicast Registration Protocol) and GVRP (GARP VLAN Registration Protocol), traffic classes priority threshold, and address aging time.
  • Layer 2 Address Table - Displays detailed statistical information for the selected port such as packet type and frame size counters.
  • Port Statistics/Statistics Menu - Displays statistics on network traffic passing through the selected port. You have a choice of viewing port or RMON statistics.
Linksys Etherfast — Switch Management diagram (page 35)
Fig. 66 · Switch Management

IGMP Snooping Configuration · Network Monitor Menu

Page 36 of the Linksys Etherfast user manual — Switch Management
Page 36 · click to enlarge
Page 36

Select OK to return to the previous panel.

The Port Statistics/Statistics Menu allows you to view the port or RMON sta- tistics.

Select OK to return to the previous panel.

  • RMON Statistics - Displays statistics for each port from RMON group 1 (RMON groups 2, 3, and 9 can only be accessed using SNMP management software).
  • Port Statistics - Displays statistics on network traffic passing through the selected port. You have a choice of viewing port or RMON statistics.
  • IP Menu - Displays information regarding a variety of IP settings, including subnets, ARP table, routing table, and multicast groups. (Not shown in screenshot. Only available in multilayer mode)
  • IP Multicast Registration Table - Displays all the multicast groups active on this Switch, including the multicast IP address and the corresponding VLANs. (Only displayed for Layer 2 mode. When the Switch is in multilayer mode, IP Multicast Registration Table is available through the IP Menu.)
Linksys Etherfast — Switch Management diagram (page 36)
Fig. 67 · Switch Management
  • In Discards - The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
  • In Non-Unicast Pkts - The number of non-unicast (that is, subnetworkbroadcast or subnetwork-multicast) packets delivered to a higher-layer protocol.
  • In Octets - The total number of octets received on the interface, including framing characters.

Select the required port.

Port Statistics display key statistics from the Interfaces Group and Ethernet-like MIBs for each port. Error statistics on the traffic passing through each port are displayed. This information can be used to identify potential problems with the Switch (such as a faulty port or unusually heavy loading). The values displayed have been accumulated since the last system reboot.

Linksys Etherfast — Switch Management diagram (page 36)
Fig. 68 · Switch Management

Port Statistics/Statistics Menu · Interfaces Group · Port Statistics

Page 37 of the Linksys Etherfast user manual — Switch Management
Page 37 · click to enlarge
Page 37
  • Excessive Collisions - The number of frames for which transmission failed due to excessive collisions.
  • Deferred Transmissions - A count of frames for which the first transmission attempt on a particular interface is delayed because the medium was busy.
  • Single Collisions - The number of successfully transmitted frames for which transmission is inhibited by exactly one collision.
  • CRC Errors - Number of Ethernet Cyclic Redundancy Check errors detected by this device.
  • Out Errors - The number of outbound packets that could not be transmitted because of errors.
  • Out Discards - The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
  • Out Non-Unicast Pkts - The total number of packets that higher-level protocols requested be transmitted to a non-unicast (that is, a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.
  • Out Unicast Pkts - The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.
  • Out Octets - The total number of octets transmitted out of the interface, including framing characters.
  • Alignment Errors - The number of alignment errors (mis-synchronized data packets).
  • In Errors - The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.

Select Apply to make changes. Select Refresh to refresh the statistics. Select OK to return to the previous panel. Select Reset to reset a specific statistic. Select Reset All to reset the all statistics. Select Prev Port to view the previ- ous port. Select Next Port to view the next port. To display a specific port, set the port number in the Port field and then press Apply.

  • Jabbers - The total number of frames received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either an FCS or alignment error.
  • Fragments - The total number of frames received that were less than 64 octets in length (excluding framing bits, but including FCS octets) and had either an FCS or alignment error.
  • Carrier Sense Errors - The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame.
  • Late Collisions - The number of times that a collision is detected later than 512 bit-times into the transmission of a packet.
  • Multiple Collisions - A count of successfully transmitted frames for which transmission is inhibited by more than one collision.
  • Octets - Number of octets passing through this port.
  • Drop Events - The total number of events in which packets were dropped due to lack of resources.

Ethernet-Like

Page 38 of the Linksys Etherfast user manual — Switch Management
Page 38 · click to enlarge
Page 38
  • CRC/Alignment Errors - The number of CRC/alignment errors (FCS or alignment errors).
  • Broadcast Frames - The total number of good frames received that were directed to the broadcast address. This does not include multicast packets.
  • Received Frames - The total number of frames (bad, broadcast, and multicast) received.
  • Received Bytes - Total number of bytes of data received on the network. This statistic can be used as a reasonable indication of Ethernet utilization.
  • Drop Events - The total number of events in which packets were dropped due to lack of resources.

Select the required port.

The RMON Statistics screen provides access to a broad range of statistics, including a total count of different frame types and sizes passing through each port. The values displayed have been accumulated since the last sys- tem reboot.

Linksys Etherfast — Switch Management diagram (page 38)
Fig. 69 · Switch Management
  • 512-1023 Byte Frames - The total number of frames (including bad packets) received and transmitted where the number of octets fall within the specified range (excluding framing bits, but including FCS octets).
  • 256-511 Byte Frames - The total number of frames (including bad packets) received and transmitted where the number of octets fall within the specified range (excluding framing bits, but including FCS octets).
  • 128-255 Byte Frames - The total number of frames (including bad pacets) received and transmitted where the number of octets fall within the specified range (excluding framing bits, but including FCS octets).
  • 65-127 Byte Frames - The total number of frames (including bad packets) received and transmitted where the number of octets fall within the specified range (excluding framing bits, but including FCS octets).
  • 64 Byte Frames - The total number of frames (including bad packets) received and transmitted that were 64 octets in length (excluding framing bits, but including FCS octets).
  • Collisions - The best estimate of the total number of collisions on this Ethernet segment.
  • Jabbers - The total number of frames received that were longer than 1518 octets long (excluding framing bits, but including FCS octets) and had either an RCS or alignment error.
  • CRC Errors - The total number of frames received that were less than 64 octets long (excluding framing bits, but including FCS octets) and had either an FCS or alignment error.
  • Fragments - The number of outbound packets that could not be transmitted because of errors.
  • Oversize Frames - The total number of frames received that were longer than 1518 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
  • Undersize Frames - The total number of frames received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.

RMON Statistics

Page 39 of the Linksys Etherfast user manual — Switch Management
Page 39 · click to enlarge
Page 39

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

The Unicast Address Table contains the MAC addresses associated with each port (that is, the source port associated with the address).

Layer 2 Address Table

Select Apply to make changes. Select Refresh to refresh the statistics. Select OK to return to the previous panel. Select Reset to reset a specific statistic. Select Reset All to reset the all statistics. Select Prev Port to view the previ- ous port. Select Next Port to view the next port. To display a specific port, set the port number in the Port field and then press Apply.

  • Port - The port whose address table includes this MAC address.
  • Address - The MAC address of a node seen on this Switch.
  • 1519-1536 Byte Frames - The total number of frames (including bad packets) received and transmitted where the number of octets fall within the specified range (excluding framing bits, but including FCS octets).
  • 1024-1518 Byte Frames - The total number of frames (including bad packets) received and transmitted where the number of octets fall within the specified range (excluding framing bits, but including FCS octets).
Linksys Etherfast — Switch Management diagram (page 39)
Fig. 70 · Switch Management

Select OK to return to the previous panel.

The Bridge Menu is used to display settings for the Spanning Tree Algorithm, as well as the global bridge settings for GMRP (GARP Multicast Registration Protocol) and GVRP (GARP VLAN Registration Protocol), traffic classes priority threshold, and address aging time.

  • Spanning Tree Port Information - Displays a list of STA values used for each port, including status, designated cost, designated bridge, and designated port.
  • Spanning Tree Bridge Information - Displays a full list of STA values used for the bridge.
Linksys Etherfast — Switch Management diagram (page 39)
Fig. 71 · Switch Management

Bridge Menu

Page 40 of the Linksys Etherfast user manual — Switch Management
Page 40 · click to enlarge
Page 40
  • Designated Root - The priority and MAC address of the device in the Spanning Tree that this switch has accepted as the root device.
  • Hold Time - The minimum interval between the transmission of consecutive Configuration BPDUs.
  • Forward Delay - The maximum time (in seconds) the root device will wait before changing states (i.e., listening to learning to forwarding).
  • Max Age - The maximum time (in seconds) a device can wait without receiving a configuration message before attempting to reconfigure.
  • Hello Time - The time interval (in seconds) at which the root device transmits a configuration message.
  • Priority - Device priority is used in selecting the root device, root port, and designated port. The device with the highest priority becomes the STA root device. However, if all devices have the same priority, the device with the lowest MAC address will then become the root device.

The STA Bridge Information screen displays a summary of STA informa- tion for the overall bridge.

Spanning Tree Bridge Information

Linksys Etherfast — Switch Management diagram (page 40)
Fig. 72 · Switch Management

Select OK to return to the previous panel.

  • Type - Shows port type as:

The STA Port Information screen displays a summary of STA information for the various ports.

Spanning Tree Port Information

  • Topology Up Time - The time since the Spanning Tree was last reconfigured.
  • Configuration Changes - The number of times the Spanning Tree has been reconfigured.
  • Root Port - The number of the port on this Switch that is closest to the root. This Switch communicates with the root device through this port. If there is not root port, then this Switch has been accepted as the root device of the Spanning Tree network.
  • Root Cost - The path cost from the root port on this Switch to the root device.

100TX 10BaseT/100Base-TX 1000T 1000Base-T

Page 41 of the Linksys Etherfast user manual — Switch Management
Page 41 · click to enlarge
Page 41

Select OK to return to the previous panel.

  • Root Cost - The path cost from the root port on this Switch to the root device.
  • Designated Port (ID) - The priority and number of the port on the designated bridging device through which this Switch must communicate with the root of the Spanning Tree.
  • Designated Bridge (ID) - The priority and MAC address of the device through which this port must communicate to reach the root of the Spanning Tree.
  • Designated Cost - The cost for a packet to travel from this port to the root in the current Spanning Tree configuration. The slower the media, the higher the cost.
  • Status - Displays current state of this port within the Spanning Tree:

Forwarding The port forwards packets, and continues learning addresses.

Learning Port has transmitted configuration messages for an interval set by the Forward Delay parameter with out receiving contradictory information. Port address is cleared, and the port begins learning addresses.

Listening Port will leave blocking state due to a topology change, starts transmitting configuration messages, but does not yet forward packets.

Blocking Port received STA configuration messages, but does not forward packets.

Disabled No link has been established on this port. Otherwise, the port has been disabled by the user or has failed diagnostics.

Select OK to return to the previous panel.

The VLAN Information screen offers access to information on the ports that have been automatically learned via GVRP and all the ports that have been configured by dynamic or static means to forward VLAN traffic.

  • VLAN Forwarding Information - Shows all the ports that have been configured by either dynamic or static means to forward VLAN traffic.
  • VLAN Dynamic Registration Information - Shows the ports that have been automatically learned via GVRP.
Linksys Etherfast — Switch Management diagram (page 41)
Fig. 73 · Switch Management

VLAN Information

Page 42 of the Linksys Etherfast user manual — Switch Management
Page 42 · click to enlarge
Page 42

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

  • Port - The ports on the Switch. Read the numbers vertically; they range from 1-26. For each port number, there are two choices:
  • VLAN - The ID for the VLAN.

The VLAN Dynamic Registration Information screen shows the ports that have been automatically learned via GVRP.

VLAN Dynamic Registration Information

Linksys Etherfast — Switch Management diagram (page 42)
Fig. 74 · Switch Management

If there is no letter “D,” it indicates that the port has not been automatically learned via GVRP.

If the letter “D” is present, it indicates that the port has been auto- matically learned via GVRP.

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

  • Port - The ports on the Switch. Read the numbers vertically; they range from 1-26. For each port number, there are two choices:
  • VLAN - The ID for the VLAN.

The VLAN Forwarding Information screen shows all the ports that have been configured by either dynamic or static means to forward VLAN traf- fic.

Linksys Etherfast — Switch Management diagram (page 42)
Fig. 75 · Switch Management

If the letter “S” is present, it indicates that the port has been con- figured by static means.

If the letter “D” is present, it indicates that the port has been con- figured by dynamic means.

VLAN Forwarding Information

Page 43 of the Linksys Etherfast user manual — Switch Management
Page 43 · click to enlarge
Page 43

The IP Multicast Registration Table displays all the multicast groups active on the Switch, including the multicast IP address and the corresponding VLANs.

IP Multicast Registration Table

  • Learned by - Shows if this entry was learned dynamically or via IGMP Snooping. An entry is learned dynamically if a multicast packet was seen crossing the port, or via IGMP Snooping if an IGMP registration packet was seen crossing the port.
  • (Multicast Group Port Lists) - The ports that belong to the indicated VLAN group. Read the numbers vertically; they range from 1-26. For each port number, there are two choices:
  • Multicast IP - A source IP address that represents a specific multicast service.
  • VLAN - A VLAN with host members that have asked to receive the indicated multicast service.
Linksys Etherfast — Switch Management diagram (page 43)
Fig. 76 · Switch Management

If there is no letter “M,” then there is no access to messages trans mitted by that particular port.

If the letter “M” is present, it indicates that the VLAN has access to messages transmitted by that particular port.

Select OK to return to the previous panel.

The IP Menu displays information regarding a variety of IP settings, includ- ing subnets, ARP table, routing table, and multicast groups. (Only available in multilayer mode).

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

  • Multicast Table - Displays all the multicast groups active on this Switch, including the multicast IP address and the corresponding VLANs. (See page 80.)
  • Routing Table - Shows the routes through which all recognized Ethernet networks (and the corresponding VLAN) can be reached.
  • ARP Table - Shows the IP-to-MAC addresses discovered by ARP.
  • Subnet Information - Displays settings for the IP interface of VLANs.
Linksys Etherfast — Switch Management diagram (page 43)
Fig. 77 · Switch Management

IP Menu

Page 44 of the Linksys Etherfast user manual — Switch Management
Page 44 · click to enlarge
Page 44

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

  • ( Ports) - The ports on the Switch.
  • VLAN - The VLAN associated with this IP interface.
  • Subnet Mask - A template that identifies the address bits in the host address used for routing to specific subnets.
  • IP Address - The IP address associated with the specified VLAN interface.

The Subnet Information screen displays information about the IP interface for VLANs configured on this Switch.

Read the numbers vertically; they range from 1-26. For each port number, there are two choices: “S” or “P.” Use the spacebar to scroll through the choices.

The letter “P” indicates the port is a static entry, and the port’s PVID is set to this VLAN ID.

The letter “S” indicates a static entry.

Linksys Etherfast — Switch Management diagram (page 44)
Fig. 78 · Switch Management

Select OK to return to the previous panel. Select First Page to view the first page. Select Next Page to view the next page.

  • Port - The port this host device is attached to.
  • VLAN - The VLAN group this host has been assigned to.
  • MAC Address - MAC address that maps to the corresponding IP address.
  • IP Address - IP addresses for which ARP has resolved the physical address through a broadcast message.

The ARP Table shows the IP-to-MAC addresses discovered by ARP.

Linksys Etherfast — Switch Management diagram (page 44)
Fig. 79 · Switch Management

Subnet Information · ARP Table

Page 45 of the Linksys Etherfast user manual — Switch Management
Page 45 · click to enlarge
Page 45
  • Type - The IP route type for the destination network.
  • Next Hop - The IP address of the router at the next hop.
  • VLAN - The VLAN within which the gateway or destination address resides.
  • Destination Mask - The subnet mask that specifies the bits to match.
  • Destination Network - A destination network, subnet, or host.

The Routing Table lists the routes through which all recognized Ethernet networks (and corresponding VLAN) can be reached.

Direct: A directly connected subnetwork Indirect: A remote IP subnetwork or host address Myself: A switch IP address on a specific IP subnetwork Bcast: A subnetwork broadcast address Mcast: An IP multicast address Invalid: An illegal IP address to be filtered

Linksys Etherfast — Switch Management diagram (page 45)
Fig. 80 · Switch Management

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply. Select Flush RIP to flush the RIP protocol.

  • IGMP Cache - Cache for IGMP.
  • Multicast Registration Table - Displays all the multicast groups active on the Switch, including the multicast IP address and the corresponding VLANs. (See page 80.)

The Multicast Table Menu offers a variety of multicasting settings.

  • Protocol - How the route was learned.
Linksys Etherfast — Switch Management diagram (page 45)
Fig. 81 · Switch Management

Local: Manually configured Mgmt: Set via SNMP ICMP: Obtained via ICMP redirect RIP: Learned via RIP protocol Other: Learned by some other method

Routing Table · Multicast Table Menu

Page 46 of the Linksys Etherfast user manual — Switch Management
Page 46 · click to enlarge
Page 46

Select OK to return to the previous panel.

  • DVMRP Neighbor Table - Table of neighbors for Distance-Vector Multicast Routing Protocol.
  • DVMRP Routing Table - Routing table for Distance-Vector Multicast Routing Protocol.
  • Multicast Forwarding Cache Table - Cache for multicast forwarding.
  • Up Time - The time elapsed since this entry was created.
  • Reporter - IP address of the source of the last membership report received for this multicast group on this interface. If no membership report has been received, this object has the value 0.0.0.0.
  • Intf - The IP interface on this Switch that has received traffic directed to the IP multicast group address.
  • Group Address - An IP multicast group address with subscribers directly attached or downstream from this Switch.

The IGMP Cache screen shows the settings for the IGMP cache.

Linksys Etherfast — Switch Management diagram (page 46)
Fig. 82 · Switch Management

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

  • V1 Timer - The time remaining until the Switch assumes that there are no longer any IGMP Version 1 members on the IP subnet attached to this interface. (The default is 400 seconds.) If the Switch receives an IGMP Version 1 Membership Report, it sets a timer to note that there are Version 1 hosts present which are members of the group for which it heard the report. If there are Version 1 hosts present for a particular group, the Switch will ignore any Leave Group messages that it receives for that group.
  • Expire - The time remaining before this entry will be aged out. (The default is 260 seconds.)

IGMP Cache

Page 47 of the Linksys Etherfast user manual — Switch Management
Page 47 · click to enlarge
Page 47

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

  • Up Time - The time elapsed since this entry was created.
  • Protocol - The multicast routing protocol associated with this entry.
  • Upstream Nbr - The IP address of the network device immediately upstream for this group.
  • Mask - Subnet mask that is used for the source address. This mask identifies the host address bits used for routing to specific subnets.
  • Source Address - The IP subnetwork at the root of the multicast delivery tree. This subnetwork contains a known multicast source.
  • Group Address - An IP multicast group address with subscribers directly attached or downstream from this Switch.
Linksys Etherfast — Switch Management diagram (page 47)
Fig. 83 · Switch Management

The Multicast Forwarding Cache displays the settings for the cache.

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

  • Up Time - The time elapsed since this entry was created.
  • Metric - The metric for this interface used to calculate distance vectors.
  • Interface - The IP interface on this Switch that connects to the upstream neighbor.
  • Upstream Nbr - The IP address of the network device immediately upstream for this multicast delivery tree.
  • Mask - Subnet mask that is used for the source address. This mask identifies the host address bits used for routing to specific subnets.
  • Source Address - The IP subnetwork at the root of the multicast delivery tree. This subnetwork contains a known multicast source.
Linksys Etherfast — Switch Management diagram (page 47)
Fig. 84 · Switch Management

The DVMRP Routing Table shows the routes for the Distance- Vector Multicast Routing Protocol.

Multicast Forwarding Cache · DVMRP Routing Table

Page 48 of the Linksys Etherfast user manual — Switch Management
Page 48 · click to enlarge
Page 48

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply.

  • RcvRoute - The total number of routes received in valid DVMRP packets from this neighbor. This can be used to diagnose problems such as unicast route injection, as well as giving an indication of the level of DVMRP route exchange activity.
  • Ver - The neighboring router’s DVMRP version number.
  • ExpireTime - The time remaining before this entry will be aged out.
  • UpTime - The time since this device last became a DVMRP neighbor to this Switch.
  • Neighbor Address - The IP address of the network device immediately upstream for this multicast delivery tree.
  • Interface - The IP interface on this Switch that connects to the upstream neighbor.

The DVMRP Neighbor Table shows information about the neighbors used for the Distance-Vector Multicast Routing Protocol.

Linksys Etherfast — Switch Management diagram (page 48)
Fig. 85 · Switch Management

Select Restart to restart the Switch. Select Cancel to cancel the system restart.

The System Restart Menu resets the management agent.

  • [Restart] - Restarts the Switch.
  • Reload Factory Defaults - Reloads the factory defaults.
Linksys Etherfast — Switch Management diagram (page 48)
Fig. 86 · Switch Management

DVMRP Neighbor Table · System Restart Menu

Page 49 of the Linksys Etherfast user manual — EtherFast ® Managed 24-Port with Dual Gigabit Switch Troubleshooting
Page 49 · click to enlarge
Page 49

If you need to return to the program, press Enter repeatedly.

The Exit command under the Main Menu is used to exit the configuration program and terminate communications with the Switch for the current ses- sion.

Linksys Etherfast — EtherFast ® Managed 24-Port with Dual Gigabit Switch Troubleshooting diagram (page 49)
Fig. 87 · EtherFast ® Managed 24-Port with Dual Gigabit Switch…
2. I forgot or lost the password. • Reinstall the switch firmware as described in the Appendix. Otherwise, contact Linksys Technical Support for help.
  • 1. I can’t connect to the Managed 24-Port with Dual Gigabit Switch using the telnet, Web browser, or SNMP software.
  • Be sure you have configured the agent with a valid IP address, subnet mask, and default gateway (Layer 2).
  • Check that you have a valid network connection to the Switch and that the port you are using has not been disabled.
  • Check the network cabling between the management station and the Switch.
  • If you cannot connect using telnet, there may already be four active sessions. Try connecting again at a later time.

This section provides possible solutions to problems regarding the installation and operation of the Managed 24-Port with Dual Gigabit Switch. If your situ- ation is described here, the problem should be solved by applying the corre- sponding solution. If you can’t find an answer here, check the Linksys web- site at www.linksys.com

Common Problems and Solutions

EtherFast ® Managed 24-Port with Dual Gigabit Switch Troubleshooting

Exit

Page 50 of the Linksys Etherfast user manual — EtherFast ® Managed 24-Port with Dual Gigabit Switch Troubleshooting
Page 50 · click to enlarge
Page 50
  • 3. I can’t access the on-board configuration program via a serial port configuration.
  • Be sure you have set the terminal emulator program to VT100 compatible, 8 data bits, 1 stop bit, no parity, and 19200 bps.
  • Check that the null-modem serial cable conforms to the pin-out connections provided below.
Linksys Etherfast — EtherFast ® Managed 24-Port with Dual Gigabit Switch Troubleshooting diagram (page 50)
Fig. 88 · EtherFast ® Managed 24-Port with Dual Gigabit Switch…

Console Port to 25-Pin DCE Port on Modem

Console Port to 9-Pin COM Port on PC

DB-9 Port Pin Assignments

Linksys Etherfast — EtherFast ® Managed 24-Port with Dual Gigabit Switch Troubleshooting diagram (page 50)
Fig. 89 · EtherFast ® Managed 24-Port with Dual Gigabit Switch…
Linksys Etherfast — EtherFast ® Managed 24-Port with Dual Gigabit Switch Troubleshooting diagram (page 50)
Fig. 90 · EtherFast ® Managed 24-Port with Dual Gigabit Switch…

Console Port to 25-Pin DTE Port on PC

Linksys Etherfast — EtherFast ® Managed 24-Port with Dual Gigabit Switch Troubleshooting diagram (page 50)
Fig. 91 · EtherFast ® Managed 24-Port with Dual Gigabit Switch…
Page 51 of the Linksys Etherfast user manual — EtherFast ® Series Appendix
Page 51 · click to enlarge
Page 51

!!! If you want to download image file, Please press to download: !!! Download Runtime image, press !!! Download Diagnostic image, press !!! Clear the system parameter block, press r Please input the Baud Rate as following: Press 1: Baud Rate = 9600 Press 2: Baud Rate = 19200 Press 3: Baud Rate = 38400 Press 4: Baud Rate = 57600 Press 5: Baud Rate = 115200 Select a number and then press !!! 5 Please change local console BaudRate to exact rate and press !!!

Power-On SElf Test (POST) Int. Loopback Testing SCC2 UART Channel ...PASS Testing the System SDRAM ...PASS Int. Loopback Testing UART Channel ...PASS Int. Loopback Testing UART Channel ...PASS CPU Self Test ...PASS FlashROM CheckSum Test ...PASS

POST Version V2.55.A03 8/18/2000

2. When the system initialization screen appears as shown below, press “ D ” to download system firmware, and then indicate the code type ( Runtime image or Diagnostic image).
1. Restart the system by using the Restart System command, or by pulling out the power cord to reset the power, waiting five seconds, and plugging it back in.

You can upgrade system firmware by connecting your computer to the serial port on the Switch and using a console interface package that supports the XModem protocol.

Upgrading Firmware via the Serial Port

EtherFast ® Series Appendix

Press to start UI

XModem Download to 0x00400020: ... SUCCESS ! (P)ermanent or (T)emporary Download: [P] Update RunTime Image at 0x03040000 SUCCESS ! Change to original Baud Rate and Press to Run Application !!! Decompress now !!! run-time code starting now. !!! Starting System ... MAINBOARD OCTOPUS0 RAMBIST TEST PASS! MAINBOARD OCTOPUS1 RAMBIST TEST PASS! MAINBOARD OCTOPUS2 RAMBIST TEST PASS! MAINBOARD OCTOPUS3 RAMBIST TEST PASS! MAINBOARD DOLPHIN RAMBIST TEST PASS! MAINBOARD STARFISH RAMBIST TEST PASS!

4. After the file has been downloaded, the console screen will display information similar to that shown below. Press Enter to download to permanent memory, and change the baud rate back to 19200. Press Enter to start decompressing the new firmware, and then press Enter to open the Logon screen.
3. Change your baud rate to the selected value, and press Enter to enable download. From the terminal emulation program, select the file you want to download, set the protocol to XModem, and then initialize downloading.

Your firmware has now been updated.

Page 52 of the Linksys Etherfast user manual — Glossary
Page 52 · click to enlarge
Page 52

CAT 3 - ANSI/EIA (American National Standards Institute/Electronic Industries Association) Standard 568 is one of several standards that specify

BOOTP (BOOTstrap Protocol) - A TCP/IP protocol that lets a device connect- ed to the network be automatically configured and booted up. An IP address is automatically assigned for a specific length of time.

Bandwidth - The transmission capacity of a given facility, in terms of how much data the facility can transmit in a fixed amount of time; expressed in bits per second (bps).

Backbone - The part of a network that connects most of the systems and net- works together and handles the most data.

Auto-negotiate - To automatically determine the correct settings. The term is often used with communications and networking. For example, Ethernet 10/100 cards, hubs, and switches can determine the highest speed of the node they are connected to and adjust their transmission rate accordingly.

ARP (Address Resolution Protocol) - A TCP/IP protocol used to figure out a host’s Ethernet address from its Internet address.

Adapter - Printed circuit board that plugs into a PC to add capabilities or con- nectivity to a PC. In a networked environment, a network interface card (NIC) is the typical adapter that allows the PC or server to connect to the intranet and/or Internet.

1000BASE-T - Provides half-duplex (CSMA/CD) and full-duplex 1000Mbps Ethernet service over Category 5e links as defined by ANSI/TIA/EIA-568-A. Topology rules for 1000Base-T are the same as those used for 100Base-TX. Category 5e link lengths are limited to 100 meters by the ANSI/TIA/EIA-568- A cabling standard. Only one CSMA/CD repeater will be allowed in a collision domain.

100BaseTX - IEEE physical layer specification for 100Mbps over two pairs of Category 5 UTP wire.

10BaseT - An Ethernet standard that uses twisted wire pairs.

Glossary

DHCP supports static addresses for computers containing Web servers that need a permanent IP address.

DHCP (Dynamic Host Configuration Protocol) - A protocol that lets network administrators manage centrally and automate the assignment of Internet Protocol (IP) addresses in an organization’s network. Using the Internet’s set of protocol (TCP/IP), each machine that can connect to the Internet needs a unique IP address. When an organization sets up its computer users with a con- nection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address must be entered manually at each computer, and, if computers move to another location in another part of the network, a new IP address must be entered. DHCP lets a network administrator supervise and dis- tribute IP addresses from a central point and automatically sends a new IP address when a computer is plugged into a different place in the network. DHCP uses the concept of a “lease” or amount of time that a given IP address will be valid for a computer. The lease time can vary depending on how long a user is likely to require the Internet connection at a particular location. It’s especially useful in education and other environments where users change fre- quently. Using very short leases, DHCP can dynamically reconfigure networks in which there are more computers than there are available IP addresses.

Data Packet - One frame in a packet-switched message. Most data communi- cations is based on dividing the transmitted message into packets. For example, an Ethernet packet can be from 64 to 1518 bytes in length.

CAT 5e - The additional cabling performance parameters of return loss and far- end crosstalk (FEXT) specified for 1000Base-T and not specified for 10Base-T and 100Base-TX are related to differences in the signaling implementation. 10Base-T and 100Base-TX signaling is unidirectional—signals are transmitted in one direction on a single wire pair. In contrast, Gigabit Ethernet is bi-direc- tional—signals are transmitted simultaneously in both directions on the same wire pair; that is, both the transmit and receive pair occupy the same wire pair.

CAT 5 - ANSI/EIA (American National Standards Institute/Electronic Industries Association) Standard 568 is one of several standards that specify “categories” (the singular is commonly referred to as “CAT”) of twisted pair cabling systems (wires, junctions, and connectors) in terms of the data rates that they can sustain. CAT 5 cable has a maximum throughput of 100Mbps and is usually utilized for 100BaseTX networks.

“categories” (the singular is commonly referred to as “CAT”) of twisted pair cabling systems (wires, junctions, and connectors) in terms of the data rates that they can sustain. CAT 3 cable has a maximum throughput of 16Mbps and is usually utilized for 10BaseT networks.

Page 53 of the Linksys Etherfast user manual — Glossary
Page 53 · click to enlarge
Page 53

Hub - The device that serves as the central location for attaching wires from workstations. Can be passive, where there is no amplification of the signals; or active, where the hubs are used like repeaters to provide an extension of the cable that connects to a workstation.

Hardware - Hardware is the physical aspect of computers, telecommunications, and other information technology devices. The term arose as a way to distinguish the “box” and the electronic circuitry and components of a computer from the pro- gram you put in it to make it do things. The program came to be known as the soft- ware.

Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a time.

GVRP (GARP VLAN Registration Protocol) - Defines a way for switches to exchange VLAN information in order to register VLAN members on ports across the network.

GMRP (GARP Multicast Registration Protocol) - Allows network devices to register endstations with multicast groups. GMRP requires that any participat- ing network devices or endstations comply with the IEEE 802.1p standard.

GARP (General Attributes Registration Protocol) - A standard for registering or deregistering client attributes for client services within a bridged LAN.

Full Duplex - The ability of a device or line to transmit data simultaneously in both directions.

Fast Ethernet - A 100 Mbps technology based on the 10Base-T Ethernet CSMA/CD network access method.

Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium. Has a transfer rate of 10Mbps. Forms the underlying transport vehicle used by several upper-level pro- tocols, including TCP/IP and XNS.

Dynamic Routing - The ability for a router to forward data via a different route based on the current conditions of the communications circuits. For example, it can adjust for overloaded traffic or failing lines and is much more flexible than static routing, which uses a fixed forwarding path.

DVMRP (Distance-Vector Multicast Routing Protocol) - Used for routing multi- cast messages through the Internet.

Multicasting - Sends data to a group of nodes instead of a single destination.

Multicast Routing Protocol - A routing protocol that supports multicast pack- ets (one to many).

Mbps (MegaBits Per Second) - One million bits per second; unit of measure- ment for data transmission.

MAC Address - The MAC (Media Access Control) address is your computer’s unique hardware number.

Layer 3 - Network layer in the ISO 7-Layer Data Communications Protocol. This layer handles the routing functions for data moving from one open system to another.

Layer 2 - Data Link layer in the ISO 7-Layer Data Communications Protocol. This is directly related to the hardware interface for network devices and pass- es traffic based on MAC addresses.

Latency - The time delay between when the first bit of a packet is received and the last bit is forwarded.

LAN - A local area network (LAN) is a group of computers and associated devices that share a common communications line and typically share the resources of a single processor or server within a small geographic area (for example, within an office building).

IGMP (Internet Group Management Protocol) - A multicast host registration protocol that allows any host to inform its local router that it wants to receive transmissions addressed to a specific multicast group.

The IEEE fosters the development of standards that often become national and international standards. The organization publishes a number of journals, has many local chapters, and has several large societies in special areas, such as the IEEE Computer Society.

IEEE - The Institute of Electrical and Electronics Engineers. The IEEE describes itself as “the world’s largest technical professional society—promot- ing the development and application of electrotechnology and allied sciences for the benefit of humanity, the advancement of the profession, and the well- being of our members.”

Page 54 of the Linksys Etherfast user manual — Glossary
Page 54 · click to enlarge
Page 54

SNMP (Simple Network Management Protocol) - A widely used network mon- itoring and control protocol. Data is passed from SNMP agents, which are hardware and/or software processes reporting activity in each network device (hub, router, bridge, etc.) to the workstation console used to oversee the net- work. The agents return information contained in a MIB (Management Information Base), which is a data structure that defines what is obtainable from the device and what can be controlled (turned off, on, etc.).

RMON (Remote MONitoring) - RMON provides comprehensive network monitoring capabilities. It eliminates the polling required in standard SNMP, and can set alarms on a variety of traffic conditions, including specific error types.

RJ-45 (Registered Jack-45) - A connector similar to a telephone connector that holds up to eight wires, used for connecting Ethernet devices.

RIP (Routing Information Protocol) - A simple routing protocol that is part of the TCP/IP protocol suite. It determines a route based on the smallest hop count between source and destination. RIP is a distance vector protocol that routine- ly broadcasts routing information to its neighboring routers and is known to waste bandwidth. AppleTalk, DECnet, TCP/IP, NetWare, and VINES all use incompatible versions of RIP.

Port Trunk - Defines a network link aggregation and trunking method, which specifies how to create a single high-speed logical link that combines several lower-speed physical links.

Port - A pathway into and out of the computer or a network device such as a switch or router. For example, the serial and parallel ports on a personal com- puter are external sockets for plugging in communications lines, modems, and printers.

NIC (Network Interface Card) - A board installed in a computer system, usu- ally a PC, to provide network communication capabilities to and from that com- puter system. Also called an adapter.

Network - A system that transmits any combination of voice, video, and/or data between users.

VLAN (Virtual LAN) - A logical association that allows users to communicate as if they were physically connected to a single LAN, independent of the actu- al physical configuration of the network.

UTP - Unshielded twisted pair is the most common kind of copper telephone wiring. Twisted pair is the ordinary copper wire that connects home and many business computers to the telephone company. To reduce crosstalk or electro- magnetic induction between pairs of wires, two insulated copper wires are twisted around each other. Each signal on twisted pair requires both wires. Since some telephone sets or desktop locations require multiple connections, twisted pair is sometimes installed in two or more pairs, all within a single cable.

Unicast Routing Protocol - A routing protocol that does not support multicast.

TX Rate - Transmission Rate.

Throughput - The amount of data moved successfully from one place to anoth- er in a given time period.

TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password capability.

Subnet Mask - The method used for splitting IP networks into a series of sub- groups, or subnets. The mask is a binary pattern that is matched up with the IP address to turn part of the host ID address field into a field for subnets.

Static Routing - Forwarding data in a network via a fixed path. Static routing cannot adjust to changing line conditions as can dynamic routing.

STP (Spanning Tree Protocol) - A technology that checks your network for any loops. A loop can often occur in complicated or back-up linked network sys- tems. Spanning-tree detects and directs data along the shortest path, maximiz- ing the performance and efficiency of the network.

Page 55 of the Linksys Etherfast user manual — Warranty Information
Page 55 · click to enlarge
Page 55

Dimensions 16.93" x 13.78" x 1.75" (430mm x 350mm x 44.4mm) Unit Weight 8.38 lbs. (3.8kg) Power Input 100-240V AC, 50-60Hz Power Consumption 60 watts Certifications FCC Class A Operating Temp. 0° C to 40° C (32° F to 104° F) Storage Temp. -10° C to 70° C (-14° F to 158° F) Operating Humidity 10 % to 95 % Non-Condensing Storage Humidity 10 % to 95 % Non-Condensing

Model Number EF24G2M Standards IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.3, IEEE 802.3ab, IEEE 802.3u, IEEE 802.3x Protocol CSMA/CD Ports 24 10/100Base-TX RJ-45 Ports 2 1000Base-T RJ-45 Ports 1 RS-232 DB-9 Port Speed Per Port (Mbps) 10/100 Ports 10 or 100 (Half Duplex) 20 or 200 (Full Duplex) 1000 Ports 1000 (Half Duplex) 2000 (Full Duplex) MAC Addresses 32k MAC Addresses 64k Max Frame Size 1522 Bytes Buffer Memory 4MB Cabling Type UTP Category 5 or Better (10/100) UTP Category 5e or Better (1000) LEDs Power, FD/Col (per Port), Link/Act (per Port)

Specifications

LINKSYS OFFERS CROSS SHIPMENTS, A FASTER PROCESS FOR PRO- CESSING AND RECEIVING YOUR REPLACEMENT. LINKSYS PAYS FOR UPS GROUND ONLY. ALL CUSTOMERS LOCATED OUTSIDE OF THE UNITED STATES OF AMERICA AND CANADA SHALL BE HELD RESPONSIBLE FOR SHIPPING AND HANDLING CHARGES. PLEASE CALL LINKSYS FOR MORE DETAILS.

IN NO EVENT SHALL LINKSYS’ LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDEN- TAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS DOCU- MENTATION. LINKSYS DOES NOT OFFER REFUNDS FOR ANY PROD- UCT.

BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE FROM THE PRODUCT’S PACKAGING ON HAND WHEN CALLING. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE.

Warranty Information

Environmental

Page 56 of the Linksys Etherfast user manual — Contact Information
Page 56 · click to enlarge
Page 56

Sales Information 800-546-5797 (LINKSYS) Tech Support 888-793-5932 RMA Issues 949-261-1288 Fax 949-261-8868 Email support@linksys.com Web http://www.linksys.com FTP Site ftp.linksys.com

For help with the installation or operation of this product, contact Linksys Customer Support at one of the phone numbers or Internet addresses below.

Contact Information

Page 57 of the Linksys Etherfast user manual — Contact Information
Page 57 · click to enlarge
Page 57

© Copyright 2001 Linksys, All Rights Reserved. Printed in the USA.

http://www.linksys.com

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Linksys Etherfast

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Linksys Etherfast

Be the first to ask — other owners or our team will answer.

Original document

Linksys Etherfast manual PDF

57 pages·2.1 MB·Network Router·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…