



About This Guide
Copyright and Trademarks
Linksys, Cisco and the Cisco Logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Other brands and product names are trademarks or registered trademarks of their respective holders. Copyright © 2008 Cisco Systems, Inc. All rights reserved.
While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons:
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
WEB: This globe icon indicates a noteworthy website address or e-mail address.
Website addresses in this document are listed without http:// in front of the address because most current web browsers do not require it. If you use an older web browser, you may have to add http:// in front of the web address.
i Player/Wireless-N Music Extender

Important Safety Instructions
Read these instructions. 1.
Keep these instructions. 2.
Heed all warnings. 3.
Follow all instructions. 4.
Do not use this apparatus near water. 5.
Clean only with dry cloth. 6.
Do not block any ventilation openings. Install in 7. accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, 8. heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized 9. or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on 10. or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the 11. manufacturer.
Use only with the cart, stand, 12. tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or 13. when unused for long periods of time.
Refer all servicing to qualified service personnel. 14. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
The socket-outlet shall be installed near the 15. equipment and shall be easily accessible.
ii Player/Wireless-N Music Extender





Wireless Home Audio Product Family
Conductor (DMC350)

Let your music play all around your home. Enjoy different songs in different rooms at the same time – or the same one everywhere in Party Mode. This is designed to let you stream, play and control your digital music via your home wireless network. The Wireless Home Audio family of devices is designed to work with your existing system to make it easy to customize complete home-filling music experiences. However you listen, you can configure a Wireless Home Audio setup perfectly suited to your space, tastes, and existing equipment. Set up in minutes – no drilling, no stringing wires.
Cisco, the world’s leader in networking technology, applied its years of knowledge and expertise to develop an amazing lossless digital audio delivery solution that preserves the full depth and richness of the recording, as originally intended by the artist. Through distributed decoding technology, each Wireless Home Audio player receives the unmodified audio source material without any trans-coding or compression. The audio is then reproduced by one or more players, synchronized to within microseconds in case of multiple players, without any of the compression and echo artifacts so often evident in other wireless audio systems. All of this means crystal clear music, exactly as recorded, anywhere in your home.
The Conductor – Wireless-N Digital Music Center is designed to let you play and command your digital music wherever you want in your home. And, as part of the Linksys by Cisco Wireless Home Audio family, it can become part of your complete, customized full-home music experience.
The stylish Conductor is an all-in-one Wireless-N music center that is designed to receive and play digital music streams over your wireless network through its built- in speakers and amplifier. It includes a CD-player if you want to simply pop in a disc. Light and easily portable, it is designed to go anywhere, so you can move it wherever you want your music to play: good in the garage, perfect for the patio, cool for the kitchen.

The intuitive 7” color touchscreen interface is designed to give you full and simple fingertip control over your listening experience. Search your music, create playlists, set up and play music in different rooms. Accesses your musical libraries on your networked PCs or storage devices, or millions of songs online through Rhapsody (30-day free trial included). Accommodates optional Docking Station for iPod, so you can access your playlists and tunes.
Controller (DMRW1000) Remote Control
Docking Station for iPod (MCCI40)
Wireless Home Audio Product Family

Director (DMC250)
Player (DMP100)


The Player – Wireless-N Music Extender is designed to enable any sound system or powered speakers to play your digital sound.
The Director – Wireless-N Music Player is designed to enable any sound system or speakers to play your digital music. The Director has a 3.5” display and can be used as a standalone or connect to other components.
This convenient, compact extender is designed to fit with your systems wherever they live and connect them to your wireless home network. A great way to enhance your home theater setup, premium audio configuration, office bookshelf unit, or any other way you’re currently enjoying music. Connect a player to each one and enjoy a multi- room music experience. Includes Infrared remote control.
Connect the Director to your existing audio system and enjoy digital music in excellent quality. It’s a great way to give your Home Theater or high-end sound systems the ability to access and play your digital music library without wires. Or build a wireless system from scratch. With its built-in 50-watt per channel amplifier, the Director can power any stand-alone speakers. Pair it with your high‑end speaker towers, or the Linksys by Cisco Stereo Speaker Kit (optional). With its compact design and elegant styling, the Director fits and looks great in any room.

The crowning touch of your Wireless Home Audio experience, the Controller - Wireless-N Touchscreen Remote is designed to give you complete, colorful at-a- touch command of your entire Linksys by Cisco Wireless Home system, from any room in your house. Wireless Home Audio: the fun, easy way to let your music play, all around your home.
Large, color touchscreen, thumbwheel, and engaging interface is designed to let you easily control any one or every one of your Wireless Home Audio devices, from anywhere in your home, even when they’re out of sight. Select listening sources, create and control listening zones and cue lists, browse and find playlists or individual songs, and more. Wireless Home Audio frees your music; the Controller frees you.

Docking Station for iPod® (MCCI40)
Other Great Linksys Products
There are many other great Linksys products that integrate perfectly with your Wireless Home Audio products.

Conveniently access and stream your media from a versatile, high-performance storage hub. Multi-stream capability lets you enjoy different media at the same time: watch a movie while your kids listen to music and your spouse browses photos. Elegant Web-based interface makes it simple to browse your media. Intelligent aggregation automatically finds, copies and organizes media from all the UPnP devices on your network -- even collecting songs from the same CD stored in different places into one virtual album.
Add your iPod to your wireless music experience and enjoy your music, podcasts, audiobooks, and all of your iTunes purchased content all around your home. The Docking Station for iPod is designed to let you integrate and control your iPod with your Linksys by Cisco Wireless Home Audio system.
Your iPod is a key part of how you enjoy your music. Now it can be a part of your Wireless Home Audio listening experience. This wired accessory makes it a snap to connect your iPod to a Linksys by Cisco Director or Conductor. Control the iPod from the Director, the Conductor, or with either the IR Remote or Wi-Fi Controller. Share your favorite tunes and playlists, advance tracks, adjust volume on each Wireless Home Audio device in your home. It even recharges docked iPods. Perfect for when friends drop by and want to include their iPods in the wireless fun. Includes adapters for most common iPod types. If you think this sounds like a great idea for a party, you’re right!
Connect everybody in your home at once without wires. Teaming the power of today’s most advanced wireless N networking technology standard with Gigabit-speed ports, the Wireless-N Gigabit Router delivers excellent performance for media-intensive activities and running multiple applications simultaneously. Easy to use and setup; includes Mac setup wizard.
Speakers (DMSPK50)
Built for speed – optimized for media. Music, movies, gaming: whatever you’re into, the Simultaneous Dual-N Band Wireless Router delivers double the bandwidth and media-optimized performance so you can enjoy it more smoothly, with less lag, all around your home. Easy to use and setup; includes Mac setup wizard.

The Stereo Speaker Kit is designed to compliment the Director - Wireless-N Music Player. These elegantly designed, high-performance vented stereo bookshelf speakers are tuned and optimized to deliver excellent music reproduction and are great for use in any room. When connected to the Director Wireless-N Music Player, they create a quality wireless audio system which you can place wherever you want in your home.

Sample Home Configuration
Click on the image below to launch an interactive Flash version of a Wireless Home Audio configuration. Place the cursor over a device to zoom in and obtain details.
Zone 4 - Office


Product Overview - Player
Front Panel
Before You Begin
This User Guide is intended to provide details on the product hardware, user interface, and use of the product. For initial installation instructions, please refer to the Quick Installation Guide included with your product.
Power (Blue/Orange) Pressing the Power button toggles between Power on and standby mode. Standby mode minimizes the power consumed by your Player when not in use. Standby mode allows you to power on your unit using the remote control or power button on the front panel.
To completely power off your Player, disconnect the power from the device.
The LED light flashes blue while the device is powering up and connecting to the network. It will remain solid blue once the device is connected to the network. When the device is in standby mode, the LED will appear orange. If the LED is red, there is an issue with the device.

Back Panel
S/PDIF Jack The S/PDIF jack provides a connector for a digital optical cable to deliver digital audio.

Ethernet The Ethernet port connects the Wireless Home Audio Player to your router or switch.
Headphone/Line Out A standard stereo mini headphone jack
Audio In Standard analog RCA left and right jacks used to deliver audio to the Wireless Home Audio Player from external sources. This input functions as a standard auxiliary input and is controlled on the external device.
Audio Out Standard analog RCA left and right jacks used to deliver audio from the Wireless Home Audio Player to an external device. This connection can be used to connect the Wireless Home Audio Player to an external receiver.
Power Connector The Power connector is where you will connect the power cord.

Setting Up Your Player
Connecting Your Player
The Player needs to be connected to some sort of powered speakers, amplifier, or headphones to play audio.
The Wireless Home Audio Installer will guide you through the setup of your Linksys by Cisco Wireless Home Audio devices.
If you have an existing stereo system that you want to connect to the Player, connect the RCA outputs on the back of the Player to the RCA inputs on your stereo system.

Below is an overview of the steps required to get up and running.
To begin, insert the CD into your CD-ROM drive. 1.
You can connect powered speakers to the Player using the RCA cables by connecting the RCA output on the Player to the RCA inputs of the powered speakers.

Click the 2. Start Setup button and follow the on-screen prompts to configure your Wireless Home Audio devices.


You can connect powered speakers to the Player using a stereo mini-plug cable by connecting one end to the Player and the other end to the powered speakers.
Your Player can be used by itself but works best when complemented with a Director or Conductor and the Controller – Wireless-N Touchscreen Remote.

The player doesn’t have a user interface screen so it is easiest to control playback using the Controller– Wireless-N Touchscreen Remote or using the Cisco Media Player software on your computer. The IR Remote that is included is fully functional but certain features such as adding favorites need to be configured with the Controller or Cisco Media Player software.
For details on the IR Remote functionality, please refer to IR Remote Control Functions, page 9.
For details on the Controller functionality, refer to the following sections:
You can connect headphones to the Player to listen to the audio.
For details on the Cisco Media Player software, refer to Using the Cisco Media Software, page 19.

IR Remote Control Functions
Volume Down Decreases the volume level of the music that is currently playing.
Infrared Lens/LED This is the area that transmits the remote functions to the device. For optimal use, point the remote directly at the device.
Stop Stops the current music selection (playing or paused music) and moves the first item played to the top of the queue which is then highlighted. The user is then brought to the Now Playing screen. The Stop button does not clear the queue.
Power/ Standby Toggles between Power On and Standby for your Conductor, Director, or Player.
Up Moves up in a list menu.
Volume Up Increases the volume level of the music that is currently playing.



Down Moves down in a list menu.
Alpha-Numeric Keypad/ Presets Numeric Keypad is the default mode. In Search and Setup modes, the keypad can be used for text entry similar to cell phones without a full keyboard, including numbers, letters and symbols. To begin playing a preset, press the Favorites button and then press the number that you selected for the preset.
Left Moves left in the carousel menu.
Right/Options Moves right in the carousel menu. It is also used to access additional options in the user interface on your Conductor or Director.
OK Selects and opens items that are highlighted in the user interface. In the Song menu, clicking OK will play that song.
Back Returns to the previous screen.
Favorites This button is a shortcut to favorites. Play a favorite track by pressing this button and the preset number.
Home Press this button once from the Home menu or twice from any other menu to go to the Now Playing screensaver.
Zero/Space This button functions as 0 in the preset list and as a space button when used in a text input field.
Add to Now Playing Queue When music is highlighted (Genre, Playlists, Artist, Album, or Song), the selected item will be added to the queue on the Now Playing screen. The queued item will be added to the bottom of the queue and will not begin playing even if it is the only item in the queue.
Search This button will open the Search field in the on-screen menu.
Previous Press this to play the previous track in the queue.

Click on this page to launch an interactive overview of the remote control functions.
Play/Pause This button toggles between playback and a paused state. If nothing is playing, pressing this button when music is selected starts playback of the selected music.
Next Plays the next song in the queue.

Using the Controller
User Interface
Carousel
Controller Touchscreen Button Functions


Navigation Arrows Scrolls through the icons in the direction selected.
Back Returns to the previous screen.
Play/Pause This button toggles between playback and a paused state. If nothing is playing, pressing this button when music is selected starts playback of the selected music.
Using the Controller to navigate through the carousel, there are multiple ways to achieve the same result:
Stop Stops the current music selection (playing or paused music) and moves the first item played to the top of the queue which is then highlighted. The user is then brought to the Now Playing screen. The Stop button does not clear the queue.
Play To Use this button to select the zones to play the music to.
Add to Now Playing Queue When music is highlighted (Genre, Playlists, Artist, Album, or Song), the selected item will be added to the queue on the Now Playing screen. The queued item will be added to the bottom of the queue and will not begin playing even if it is the only item in the queue.
Now Playing Queue Press this button for a shortcut to the Now Playing screen. The Now Playing screen shows the currently playing song and a list of your music in your queue.
Selected Device Touch to choose the device or zone that you want to control. All actions (Play, Stop) will be directed to that device/zone.

Lists
Play To Use this button to select the zones to play the music to.


Add to Favorites Adds the selected items to your list of favorites. You can add tracks, albums, or playlists to your favorites. Once you select this option you will be prompted to assign a favorite position number to the selection. You can press the touchscreen to select a number or scroll and select.
Remove Single Item Removes the item that was last selected before pressing this option.
Clear Now Playing Queue Remove all tracks from the Now Playing Queue.
Using the Controller to navigate through a list, there are multiple ways to achieve the same result:
Shuffle Select this option to randomly shuffle the playback order of the tracks in the Now Playing Queue.
Repeat This option will repeat the tracks in the Now Playing Queue once all of tracks in the queue have been played. To turn repeat off, return to the Quick Action menu and select Repeat off.
Remove All This option removes all currently stored favorites.
Rename Use this to rename a favorite. The touchscreen keyboard will appear and allow you to edit the current name.

Action Menus provide quick shortcuts that change depending upon your location in the interface.
Pressing right on the 5-Way Button/Scroll from a list menu displays the quick action options. You can select an action directly using the touchscreen or use the Scroll to navigate to the appropriate selection and press the center to select. Below is a list options you will encounter.

Common Uses
Playing Your Music
When you connect a USB drive to the Director or Conductor, a USB drive icon will appear on the carousel.
The Linksys by Cisco Wireless Home Audio system provides you with an extensive assortment of source options for playing audio throughout your home.

The optional Docking Station for iPod® (MCCI40) lets you connect your iPod to the Director or Conductor and play your iTunes music throughout your home. For details on connecting the Docking Station, please refer to the QIG that comes with it or the User Guide for your Director or Conductor.
Use the scroll or the left 1. and right buttons on the touchscreen or 5-Way button to move through the menu items. Press Devices on the touchscreen to or use the center of the 5-Way button to select it.
Once you select this option, you will be able to sort through the songs on the drive by Artist, Album, or Genre. You can also Browse through the folders or Search by Artist, Album, or Song title.


A list of options will appear. You can now navigate 2. through the music and audio on your iPod. Audio is sorted by Playlist, Artist, Album, Genre, Track, Podcast, Composer, and AudioBook.
For details on navigating through the content on your USB drive, refer to Artists, page 26, Albums, page 26, Genres, page 26, Search, page 27, and Browse Folders, page 27.

Installing the Cisco Media Server software on your computer allows you to play music from your computer on your Director, Conductor, or Player. The Cisco Media Player software allows you to control playback of your Wireless Home Audio devices from your computer.
When the Cisco Media Server software is installed and running, you will see a music note icon indicating that a shared library is available for playback. Browsing the media is performed the same way as if you were browsing a USB drive connected to your Wireless Home Audio device.
There are multiple options for navigating through the list:

Press directly on an item on the touchscreen or navigate through list menus by using the scroll or pressing the down and up buttons on the 5-Way button.

Press directly on an item on the touchscreen or press the center of the 5-Way button to view tracks in an album, playlist, or associated with an artist and press the Back button on the touchscreen to return to the title.
Press the Play button to start playing a title.
For additional details on the Rhapsody menus, refer to Rhapsody, page 24.
For additional details, refer to Using the Cisco Media Software, page 19.
Radiotime provides streaming access to over 100,000 radio stations and shows. You can locate shows based on location, topic, or music genre.
Rhapsody is the critically-acclaimed digital music service that provides its members unlimited access to millions of full-length, CD-quality tracks. With Rhapsody and your new Linksys by Cisco Wireless Home Audio product you will have instant access to all of your favorite music. Listen whenever you want, play continuous music with Rhapsody Channels and discover new music and old favorites.

The initial Rhapsody menu is a carousel menu.

When you select RadioTime, a list menu will appear with options that allow you to browse local radio stations, talk shows, sports shows, music genres, and stations in locations across the world.

Use the left and right buttons on the touchscreen or 5-Way button to move through the menu items. You can also use the scroll to move through the items.
Select an item on the touchscreen or press the center of the 5-Way button to select an item.

Press directly on an item on the touchscreen or navigate through list menus by using the scroll or pressing the down and up buttons on the 5-Way button.
For additional details on RadioTime, refer to RadioTime, page 29.
You can stream music from external sources such as turntables, stereo systems, DVD players, video cameras,

karaoke systems, and generic MP3 players using the RCA inputs on the back of your Director or Player.
For additional details, refer to Source, page 30.
Playlists can be created on your Director or Conductor by adding music to the Now Playing Queue and saving the queue as a favorite.
The playlist will be created as a favorite titled Queue 7. with the date displayed in parenthesis as part of the name.

To create a playlist on your Director or Conductor, perform the following steps:
Locate a song, album, artist, genre, or existing playlist 1. that you want in your new playlist.

If you want to rename this newly created preset, perform the following steps:
Press the 2. Add to Now Playing Queue
button on the touchscreen.
Repeat steps 1 and 2 until you’ve added all that you 3. wanted to your playlist.
Press the 4. Now Playing Queue
button.
Press right on the 5-Way button and select 5. Add to Favorites.
There are 10 favorite positions that can be used to store favorite tracks, albums, playlists, genres, artists or channels. When you select an album, playlist, genre, or artist, a playlist of available tracks is created at the time you add the favorite. If you add or remove tracks from the album, playlist, genre, or artist you will need to add it as a favorite again to update it.
Use the Scroll/5-Way Button to select a favorite 6. position.

For example, if you select an artist in Rhapsody, a playlist containing their entire catalog at the time of the selection will be created. Any time that you select this Favorite, this playlist will be added to the Now Playing Queue. If the artist releases a new song or album and you want to add it to the existing favorite, simply overwrite the existing favorite by adding this artist as a favorite again.
Press right on the Scroll/5‑Way button. 2.
Select 3. Add to Favorites on the touchscreen or use the Scroll/5-Way button to select it.
If you select an artist from your iPod, a playlist will be created containing all of the tracks from the selected artist located on your iPod at the time that the favorite is created. Playing the favorite will add these tracks to the Now Playing Queue. If you add additional songs from the artist to your iPod and want to add them to the existing favorite, simply overwrite the existing favorite by adding this artist as a favorite again.

Use the Scroll/5-Way Button to select a favorite 4. position. There are ten favorites available.
If a song is added or deleted from the selected playlist after it has been added as a favorite, the changes aren’t reflected in the favorite unless you overwrite the existing favorite by adding the playlist as a favorite again.

For example, if you have a USB drive attached and select the Alternative genre on the USB drive, a playlist will be created that contains all of the music on the USB drive that is tagged as alternative.
To create a favorite, perform the following steps:
Using the Controller, locate and highlight the track, 1. album, playlist, genre, or artist that you want to set as a favorite.
To play a favorite, go to the 1. Home menu.
Locate and select 2. Favorites.


To add music to the queue using the Controller, perform the following steps:
Using the Controller, locate and highlight the track, 1. album, playlist, genre, or artist that you want to add to the queue.
Use the Scroll to find the favorite that you want to play. 3. Select it on the touchscreen or press the center of the 5-Way button to select it.

Press the 2. Add to Now Playing Queue
button on the touchscreen.
A message will appear indicating that the tracks have 3. been added to the queue.
You can view the queue by pressing the Now Playing Queue
button on the touchscreen or pressing the Home button on the Controller twice.
The Queue is cleared whenever you select to play an item (track, album, artist, genre, or playlist) instead of adding it to the queue. The item that was selected will be added to the Now Playing Queue.
The Queue contains the track that is currently playing and any additional tracks that have been added to the queue. Adding songs to the queue allows you to play songs continuously without interruption. The songs are played in the order that they were added to the queue unless you select Shuffle. You can also turn on Repeat which will continuously repeat the tracks that are in the queue.
To remove individual tracks from the queue, perform the following steps:
Go to the 1. Now Playing Queue.
When you select to play an album, playlist, genre, or artist, all of the available tracks on the selected media are added to the queue. Anytime that you select to play music, it clears out the current queue and adds the content that you’ve chosen to play to the queue. If you don’t want to immediately clear out your queue, you need to use the Add to Now Playing Queue button when you make your selection instead of using the Play button.
Locate and highlight the track that you want to remove 2. using the scroll.
Press right on the Scroll/5‑Way button. 3.
Select 4. Remove Single Item on the touchscreen or use the Scroll/5-Way button to select it.



To turn Repeat off, follow the same steps. The Repeat button will indicate Repeat Off.
Whenever you play an item, the queue is immediately cleared and the item that you selected is added to the queue. If you do not want to clear the queue, be sure to add the item to the Now Playing Queue instead of selecting play.
Shuffle generates a random playback order of the tracks in the queue.
To shuffle the order, perform the following steps:
Go to the 1. Now Playing Queue.
When you locate an item that has more than one track associated with it such as an album, playlist, genre, or artist, you can either select it to view the details of the item or add it to the Now Playing Queue or set it as a Favorite.
Press right on the 5-Way button. 2.
Use the scroll or press down to move down the list and 3. select Shuffle.

The Controller allows you to control all of your Wireless Home Audio devices from a central remote that uses Wireless-N technology to provide you with extended range and portability.
You can play different songs on individual devices or link them so that multiple devices play the same songs in perfect synchronization by selecting party mode.
Press here on the touchscreen to open the 1. Device Control window.

Repeat allows you to continuously play the music in the queue. Once the end of the queue is reached, the track at the top of the queue will begin playing and playback will be continuous until you stop music playback.
Go to the 1. Now Playing Queue.
Press right on the 5-Way button. 2.
Use the scroll or press down to move down the list and 3. select Repeat..
From the Device Control window, press the device you 2. want to control on the touchscreen or use the 5-Way Button/Scroll to select the device.

The Now Playing Queue

The Now Playing Queue appears (unless disabled) after the time configured in Settings > General Settings > Now Playing Screen Set Up. This screen displays the album artwork, artist name, song title, and a track duration progress bar and the queue of songs to be played
You can also get to this screen by pressing the Home button once from the home menu or twice from anywhere else in the interface.

The upper right corner of the touchscreen should now show the device that you selected. This area indicates which device is currently being controlled. Use the same procedure to change to another device.
Party Mode allows you to link up all of your Wireless Home Audio devices to play the same music throughout your home. To enable party mode, perform the following steps:
Setting Up Party Mode
The Quick Action menu can be selected from the Now Playing Queue by pressing right on the 5-Way button. Move down the list for additional options.
Go to the 1. Play To option from the home menu.
Select 2. Play To All ‘Party Mode’.

A message will appear stating that the linking has been successful. To unlink the devices, select Play To Local.

Volume Control
*iTunes Plus files are not protected ††
The Cisco Media Server software should start automatically but if you need to start it manually, follow these steps:
Using the Controller, you can control the volume on multiple devices using the Controller. You can control individual or linked zones.
Go to 1. Start > Programs > Cisco Media Center > Cisco Media Server.
Press the Volume 1. button on the Controller.


Use the scroll to raise or lower the volume. Scrolling 2. clockwise will raise the volume, counterclockwise will lower the volume.
If you have multiple devices connected, you can use 3. a master volume control (when in Party mode) by adjusting the volume for Linked Zone. To navigate to an individual zone, use the Volume button to go through the list. Use the scroll to raise or lower the volume.
The Cisco Media Server will launch and a gray 2. Cisco Media Server
icon will appear on your taskbar. Right-click on the Cisco Media Server
icon and select Start.

Using the IR Remote, you can control the volume on the Player directly by pressing the Volume Up button or Volume Down button
The Cisco Media Server will launch and you will see 3. a green Cisco Media Server
Pressing the Power button on the remote toggles between Power on and standby mode. Standby mode minimizes the power consumed by your Wireless Home Audio device when not in use. Standby mode allows you to power on your unit using the remote control or power button on the front panel.
icon indicating it is ready. Once the Cisco Media Server is launched, you will not see any other windows indicating what music is being shared or providing any further control. You can view the shared library from your Wireless Home Audio Devices or launch the Cisco Media Player on your computer to view the shared libraries.
If you need to completely power off your Player, you will need to disconnect the power from the device.
Using the Cisco Media Software
The Cisco Media Server software and Cisco Media Player software are installed on your computer when you run the installation program from the LELA CD-ROM.
During the initial configuration, you are asked to select directories where your music is stored. To change or add additional directories, perform the following steps:
The Cisco Media Server software allows you to share the library of music from your computer’s hard drive with your Wireless Home Audio devices.
Right‑click on the 1. Cisco Media Server
icon on the taskbar and select Cisco Media Server Properties.

NOTE: Some iTunes files may not be available. Songs purchased from iTunes* may be protected with Digital Rights Management (DRM); DRM files cannot be played to your Wireless Home Audio devices directly from your PC. The optional Linksys by Cisco Docking Station for iPod (MCCI40) will allow you to connect your iPod to your Director or Conductor and play back all of the songs from your iPod.
Modify or type in a new directory in the 2. Local Media Directory field by typing in the entire path such as
Volume Control

C:\Documents and Settings\username\My Documents\My Music;


Additional directories are separated by a semicolon. If you want to change the name that appears on your network, you can modify the UPnP Friendly Name. Click OK after all updates are complete.


Right‑click on the 3. Cisco Media Server
icon on the taskbar and select Stop.


The Cisco Media Player allows you to control your Wireless Home Audio devices from a computer. You can play music to individual zones, link zones, add songs to the queue and control the volume.
To launch the Cisco Media Player software, go to Start > Programs > Cisco Media Center > Cisco Media Player.
The Media Player Interface contains several regions used for navigation, selection, and control of your Wireless Home Audio devices and libraries.
Once the Cisco Media Server has stopped and the icon 4. has turned gray, right-click on the Cisco Media Server
icon and select Start to start the server again.



The additional music should now be accessible from your media library.
Zones are displayed on the left side of the interface. A zone is selected when it is highlighted with a cyan border (as shown in the following image). The zone window displays playback controls, album art, a track progress bar, and the Queue, Play To, and Analog In tabs.



When a track is being played, a Now Playing icon will appear to the left of the track title. You can double-click on another song title to play that song instead of the track that is currently playing and move to that spot in the queue.
You can right-click on a track in the queue for additional track options:


Playback Control Functions Table A–
Volume Control The Volume Control slider allows you to adjust the volume for the selected device. You drag the slider up to increase the volume or down to lower the volume.
Bass/Treble Adjustment The upper right corner of the zone window displays an icon that allows brings up a the adjustment sliders for the bass and treble audio settings.
Previous Press this to play the previous track in the queue.
Stop Stops the current music selection (playing or paused music) and moves the first item played to the top of the queue which is then highlighted. The Stop button does not clear the queue.
Play/Pause This button toggles between playback and a paused state. If nothing is playing, pressing this button when music is selected starts playback of the selected music.
Next Plays the next song in the queue.
Repeat Now Playing Queue When this option is enabled, the Now Playing Queue will start playing again once the end of the queue has been reached.
The Queue tab also contains two buttons at the bottom of the window:

Queue The Queue tab displays a list of of the songs in the order they appear in the queue with the Song title, Artist name, and duration (Time) of the song.
Button Function

Play To The Play To tab displays the available zones with a checkmark indicating which zone is currently being controlled. The volume level can be controlled by using the volume slider on the Play To tab or at the top of the Zone window.




The Favorites window displays all of the Favorites that have been created on your Wireless Home Audio system. Double-click a favorite to add it to the queue of the selected zone.
You can create a Favorite in the Cisco Media Player interface by selecting a track or multiple tracks (use shift to select multiple tracks) from the details portion of the interface and dragging it to a Favorite position.
You can right-click on a favorite for additional options:


Analog In The Analog In tab allows you to select and play audio from the analog input on the back of the device you are controlling. Double-click Device : Analog Line In to replace the existing queue with the analog line in option.


Favorites

Reset Error Notification Resets error notification.
Manage Account Details This is used to modify your Cisco Username and Password.
The Menu options vary depending upon the Media Source selected. The Menu allows you to navigate through libraries and channels.
The View menu toggles the interface options that are displayed on the screen.


Media Sources are displayed and can be selected from this area. Click on the Media Source that you want to browse and select content from.
Go to File and select Exit when you want to exit the Cisco Media Player or use the X in the upper right corner to close the application.
Learn More Links to the Internet for additional information.
When these options are selected, the functions are performed on the zone that is highlighted (cyan border).
Downloads Links to the Internet for downloads for the Wireless Home Audio devices.
Play Plays the current track in the queue.
About Displays version information.
Pause Pauses the music and the song will continue once play is selected.
Stop Stops the current music selection (playing or paused music) and moves the first item played to the top of the queue which is then highlighted. Stop does not clear the queue.
Next Plays the next song in the queue.
Previous Select this option to play the previous track in the queue.
Shuffle This is a one time action that shuffles the queue contents into a random order.
Toggle Repeat Turns on or off the repeat function.
Increase Volume Raises the volume level.
Decrease Volume Lowers the volume level.
Mute Selected Zones This will mute the audio so that you do not hear any music playing. The music will continue to play but will not be audible.
Unmute Selected Zones This restores the audio from a muted state.
Rediscover Zones & Sources Use this option if a zone or library is not appearing. This will search for all available zones and sources.

Using Your Player with the Controller
My Library
The Controller provides the optimal experience for controlling your Player.
Use the Controller touchscreen or scroll/5-Way button to navigate and select options. You can press options directly on the touchscreen or use the scroll or the up and down buttons to navigate through options. Press the center of the 5-Way button to select an option or select it directly on the touchscreen. Use the Home button to return to the home screen from anywhere in the interface. If you are already at the home screen, pressing the Home button will display the Now Playing Queue.
My Library allows you to connect to favorite tracks and albums that you’ve bookmarked in Rhapsody’s extensive online music library. To bookmark tracks and albums in Rhapsody Online, you need to access Rhapsody Online from your computer and locate a track or album that you want to add. To add the album or track, click the + (plus sign) next to it and select Add to My Library.
Press the Home button on the Controller once from the Home menu or twice from any other menu to go to the Now Playing Queue.

Rhapsody is a digital music service that lets you listen to their entire catalog for one monthly price. Rhapsody’s catalog contains millions of songs and thousands of artists.

The initial Rhapsody menu is a carousel menu. Use the scroll or the left and right buttons on the touchscreen or 5-Way button to move through the menu items. Press an item on the touchscreen to select it or use the center of the 5-Way button to select.
Navigate through the lists by using the scroll or the down and up buttons on the 5-Way button. Press an item on the touchscreen or use the center of the 5-Way button to view tracks in an album, playlist, or associated with an artist and press the Back
Allows you to search by Artist, Album, or Track.
button to return to the title. Press the Play
button to start playing a title.

Music Guide
Playlist


Music Guide provides access to new releases, Rhapsody’s staff picks, exclusive content that you will only find on Rhapsody, featured albums and music/artists ranked by popularity.
Rhapsody has an area for playlists called Playlist Central that features playlists compiled by Rhapsody users and celebrities as well as playlists categorized by genre, artist, decade, and other themes. The top playlists and featured playlists can be accessed from this option.

Once the Media Server software has been installed and configured on a computer, you can control playback of music on the computer from within the Wireless Home Audio Director interface.
When you select the My Music option, a carousel menu is displayed that allows you to browse music by artist, album, genre, or browse the folders located on the USB device. You also have the option to search by artist, album, or genre.
Rhapsody Channels play continuous streams of music and are similar to radio station channels but without commercials.

Artists
Selecting an album title will display all of the track titles from the selected album available on the selected media.
Highlighting an album title and pressing the Add to Now Playing Queue
button on the touchscreen adds all tracks on the selected media from the album to the Now Playing Queue. This doesn’t disrupt any tracks that are currently playing.
Highlighting an album title and pressing the Play
button will clear any tracks currently in the Now Playing Queue and add all tracks from the album located on the selected media to the Now Playing Queue. Any track that was previously playing will be stopped and the first track available from the album will begin playing immediately.
Selecting Artists will display an alphabetical list of artists that are available on the selected media.
Selecting an artist brings up a screen with an option titled All and options for each album title available on the selected media from the selected artist. Selecting All will display all track titles by the selected artist on the selected media. Selecting an album title will display the tracks from the album that are located on the selected media.

Highlighting an artist name and pressing the Add to Now Playing Queue
button on the touchscreen adds all tracks on the selected media by the selected artist to the Now Playing Queue. This doesn’t disrupt any tracks that are currently playing.
Highlighting an artist name and pressing the Play
button will clear any tracks currently in the Now Playing Queue and add all tracks on the selected media by the selected artist to the Now Playing Queue. Any track that was previously playing will be stopped and the first track by the artist will begin playing immediately.
Selecting Genres will display an alphabetical list of musical genres that are available on the selected media. The genre must be tagged properly in the audio file for this to work correctly. All tracks that do not have a genre tagging will be listed under Unknown Genre.
Selecting a genre brings up a screen with an option titled All and options for each artist in the selected genre available on the selected media. Selecting All will display all track titles associated with the genre on the selected media. Selecting an artist will display the tracks from the artist that are located on the selected media.

Highlighting a genre and pressing the Add to Now Playing Queue
button on the touchscreen adds all tracks on the selected media from the selected genre to the Now Playing Queue. This doesn’t disrupt any tracks that are currently playing.
Highlighting a genre and pressing the Play
button will clear any tracks currently in the Now Playing Queue and add all tracks from the selected genre located on the selected media to the Now Playing Queue. Any track that was previously playing will be stopped and the first track available from the genre will begin playing immediately.
Selecting Albums will display an alphabetical list of album titles that are available on the selected media.

Search
USB Media

Search allows you to locate music by artist, album, or song. Once you select artist, album, or song, a search field and the touchscreen keyboard will appear.
When you connect a USB device to the Director or Conductor, a carousel menu is displayed that allows you to browse music by artist, album, genre, or browse the folders located on the USB device. You also have the option to search by artist, album, or genre.
Enter the title using the keyboard touchscreen and press the Search button.

When you have an iPod connected to your Director or Conductor using the optional Docking Station for iPod (MCCI40), you find music in the same manner that you do on your iPod. A list menu is displayed with the options to view by playlist, artist, album, genre, track, podcast, composer, or audiobook.

The Browse Folders option allows you to browse all of the folders located on your selected media. Folders will be displayed even if they do not contain any music.
Use the scroll or up and down buttons on the 5-Way button to navigate the list. Select an option by pressing it on the touchscreen or pressing the center of the 5-Way button.

Playlist Displays a list of playlists created on your computer using iTunes.
button on the touchscreen to add the tracks from the selected playlist to the Now Playing Queue. This doesn’t disrupt any tracks that are currently playing.
button on the touchscreen to add all tracks from the selected genre to the Now Playing Queue. This doesn’t disrupt any tracks that are currently playing.
button with a genre highlighted to begin playing the first track from the genre and add all of the tracks from the genre to the Now Playing Queue. Any track that was previously playing will be stopped and the first track from the genre will begin playing immediately.
button with a playlist highlighted to begin playing the playlist and add all of the tracks in the playlist to the Now Playing Queue. Any track that was previously playing will be stopped and the first track from the playlist will begin playing immediately.
Artist Displays a list of artists available on your iPod.
Track Displays an alphabetical list of all track titles located on your iPod.
button to add the track to the Now Playing Queue. The track will be added to the end of the Now Playing Queue and will not disrupt any music that is currently playing.
button on the touchscreen to add all tracks from the selected artist or album to the Now Playing Queue. This doesn’t disrupt any tracks that are currently playing.
button to clear the Now Playing Queue and add the selected track to the Now Playing Queue. The track will begin playing immediately.
button with an artist or album title highlighted to begin playing the first track from the artist or selected album and add all of the tracks to the Now Playing Queue. Any track that was previously playing will be stopped and the first track from the artist or album will begin playing immediately.
Podcast Displays an alphabetical list of podcasts available for playback.
Composer Displays an alphabetical list of all composers of the songs on your iPod.
AudioBook Displays an alphabetical list of audiobooks available for playback.
Album Displays an alphabetical list of album titles that are available on your iPod.

button on the touchscreen to add all tracks from the selected album to the Now Playing Queue. This doesn’t disrupt any tracks that are currently playing.
button with an album title highlighted to begin playing the first track from the album and add all of the tracks to the Now Playing Queue. Any track that was previously playing will be stopped and the first track from the album will begin playing immediately.
The All Libraries option will display all of your media volumes that are available for playback. This includes any USB drives and media being shared using the Cisco Media Server software.
Genre Displays an alphabetical list of musical genres that are available on your iPod.

Favorites

Browsing the content from All Libraries is the same as when you browse content on a USB drive. For details on searching through library content, refer to USB Media, page 28.
There are 10 favorite positions that can be used to store favorite tracks, albums, playlists, genres, artists or channels.
Selecting Favorites from the main menu will bring up the list of favorites that have been configured.
RadioTime provides streaming Internet radio broadcasts from all over the world. Station titles are displayed with location listed in parenthesis. When a syndicated talk show is selected, a list of affiliates carrying the broadcast is available for selection.
Scroll through the list or use the down and up buttons on the 5-Way button to move through the list of favorites. You can select a favorite on the touchscreen or press the center of the 5-Way button to select it.
Local Radio Displays a list of local FM and AM band radio stations that are accessible via RadioTime.
For details on creating favorites, refer to Creating and Using Favorites, page 14.
Browse Talk Brings up a list of various talk radio topics for selection. Select a topic and then you can bring up a list of stations that fit that category.

Browse Sports Provides links to radio stations that offer sports programming available on RadioTime.
Browse Music Select from a list of music categories. Once you select a category of music, a list of stations playing music that fits within that category appears.
Browse by Location Use this feature to find radio stations located all over the world. Stations are categorized by region.
Selecting Now Playing Queue from the main menu will bring up the Now Playing Queue. You can also bring up the screen by pressing the Home button on the Controller

once from the main menu or twice from anywhere else in the interface.
A message will appear stating that the linking has been successful. To unlink the devices, select Play To Local.
The Now Playing Queue displays the current track that is playing and the songs that are next up in the queue. You can move through the queue using the scroll or the down and up buttons on the 5-Way button.
The Settings option contains many configuration options for your Director. Following is a list of settings that are configured with details on the following pages:
The Now Playing icon indicates which track in the queue is currently playing. If you want to immediately play another track in the queue, select the track on the touchscreen or press the center of 5-Way button.

Play To allows you to link and unlink zones. You can play tracks to an individual player or select Party Mode to sync up all of your Wireless Home Audio devices. Audio will playback perfectly in sync on the devices throughout your home. To enable Party Mode, press Play To All ‘Party Mode’.
You can connect any external analog audio source to your Wireless Home Audio network using the RCA input jacks on the back of your Director or Player and play the music to all the devices in your home.
This allows you to stream music from sources such as turntables, stereo systems, DVD players, video cameras, karaoke systems, and generic MP3 players.
To play external analog audio, ensure that the RCA outputs are connected from your external device to the RCA inputs of the Director and perform the following steps:
Select 1. Settings from the main menu.

Select 2. Source from the Settings menu.
Select 3. Analog Line In on the Source screen.

The audio from your RCA inputs will be played on the device. If you want it to play throughout your home, be sure you have your zones linked. The Now Playing Queue will indicate that the Analog Line In is being played.
Advanced This option is used for IP configuration. A dynamic or static IP address can be selected here.
The Wireless Settings option allows you to modify your wireless network settings.
Select Network Use this option to select a wireless network name (also known as an SSID) from the list of available networks or enter a wireless network name manually by selecting Enter Network Name. To enter the name manually, use the touchscreen keyboard on the Controller and press Enter when done.
Details This option displays the current network connection settings including the wireless network name, wireless security type, DHCP status, IP address, subnet mask, gateway, and DNS information.
Once the wireless network name has been selected, a screen will appear asking for the wireless security mode utilized on the network.

Set Time A series of screens will appear allowing you to enter the month, day, year, and time manually.

Set Time Zone Select your local time zone.
Daylight saving This option should be selected when observing daylight saving time.
Time Format This allows you to select a 12 hour or 24 hour time format. The 12 hour format is the default setting.
Date Format Allows you to specify the order that the day, month, and year are displayed.
Now Playing Screen Set Up
Rename Zone This option is used to rename a device with a name that will allow you to know where it is located in your home. This makes it much easier to select which areas to play music to or link.

Rediscover If one of the Wireless Home Audio devices or one of your libraries on the network is not appearing, use this option to rescan for any devices or libraries that are not showing up.

The Now Playing Screen can be turned OFF or set to start after an idle period of 30 seconds, 60 seconds, or 2 minutes.
OK button Set Up

The General option allows you to configure general devices settings for your Director.

This option defines that action that will occur when the OK button is pressed on the IR remote. The options are the following:
Auto update When this option is enabled, the date and time settings are automatically updated via the Internet.
Zones and Libraries · Date/Time

Sleep Timer Set Up

Play button Set Up

The Sleep Timer can be turned OFF or set to start after an idle period of 30 seconds, 60 seconds, or 2 minutes. Sleep turns off the display on the screen to conserve battery power.
This option provides a safeguard from automatically eliminating the contents of the Now Playing Queue when pressing the Play

button. The following are the options:
button is pressed. This reminder will verify that you want to replace the contents of the Now Playing Queue with the item you selected. You need to press OK to continue or the Back
button to cancel.
button is selected, the selected item will start playing immediately and replace the contents of the Now Playing Queue. Any track that was previously playing will be stopped.
Hibernate can be turned OFF or set to start after an idle period of 10, 20, or 45 minutes. Hibernate mode conserves more battery power and is useful for long periods of idle time.


Use this option to calibrate your touchscreen. Press the center of the + symbol when it appears on the screen. When the OK appears on the screen, press the center of the 5-Way button.
Use the scroll on the Controller to adjust the brightness level of the viewing screen. After a few seconds of idle time the brightness adjustment slider window will close or press the Back
button to return to the list of settings.
Hibernate Set Up · Calibrate Touch Screen

Set Bass/Treble

Treble Setup Use the scroll on the Controller to adjust the high frequency audio playback level on the selected Wireless Home Audio device. After a few seconds of idle time the treble adjustment slider window will close or press the back button to return to the list of settings.
Bass Setup Use the scroll on the Controller to adjust the low frequency audio playback level on the selected Wireless Home Audio device. After a few seconds of idle time the treble adjustment slider window will close or press the back button to return to the list of settings.

Version Displays the version of the software installed on the Wireless Home Audio Director.
Autoupdate This feature will automatically check online for updates to the software installed on the Wireless Home Audio Director.
Check for update now This option can be used to check manually for an update to the software installed on the Wireless Home Audio Director.

Troubleshooting
My Cisco Media Server content is not appearing on my Wireless Home Audio devices but it seems to be running.
Do I need to run the CD to configure my Wireless Home Audio devices?
You may need to reconfigure of disable yours Windows firewall.
Yes. Basic settings can be applied on some devices via their screens, but in order to fully configure your Wireless Home Audio devices you must use the CD.
My devices are not showing up on the main menu carousel.
Perform each of the following steps until you are able to locate the devices on your main menu.
How do I share my music from additional computers and allow them to control my Wireless Home Audio devices?
Run the CD on your additional computers and select the Connect Computers option on the first screen.
Where do I find the Cisco Media Center software after installation is complete?
Go to Start > Programs and select Cisco Media Center. You can start the Cisco Media Player from here.
What do I do if my iTunes library or other audio files are not found by Cisco Media Center?
Some iTunes files may not be available. Songs purchased from iTunes* may be protected with Digital Rights Management (DRM); DRM files cannot be played to your Wireless Home Audio devices directly from your PC. The optional Linksys by Cisco Docking Station for iPod (MCCI40) will allow you to connect your iPod to your Director or Conductor and play back all of the songs from your iPod.
*iTunes Plus files are not protected ††
During the initial configuration, you are asked to select directories where your music is stored. To change or
add additional directories, right‑click on the
icon on the taskbar and select Properties. Modify or type in a new directory by typing in the entire path such as C:\Documents and Settings\username\My Documents\ My Music; in the Local Media Directory field. Additional directories are separated by a semicolon. Click OK after all updates are complete.
How do I start the Cisco Media Server software?
For details on starting the Cisco Media Server software, refer to Starting the Cisco Media Server Manually, page 19.

Specifications
Dimensions 5.43" x 2.37" x 5.47" (H x W x D) 138 x 60 x 139 mm
WiFi Standards Draft Dual Band 802.11n, 802.11g, 802.11b (2.4 GHz and 5 GHz)
Weight 1.28 lb (0.58 kg)
Power 100-240 VAC Input, 5VDC Output
Certification FCC, CE, TUV
Security features WEP, WPA, WPA2
Operating Temp. 32 to 104° F (0 to 40° C)
Security key bits 64, 128, 256
Storage Temp. -4 to 158° F (-20 to 70° C)
# of Antennas Internal Antennas Only
Operating Humidity 10 to 85% Noncondensing
Storage Humidity 5 to 90% Noncondensing
RF Pwr (EIRP) in dBm 11b=17dBm, 11g/n=16dBm
Antenna Gain in dBi 2.6 dBi (2.4 GHz), 4.6 dBi (5 GHz)
Specifications are subject to change without notice.
UPnP able/cert UPnP able
Ports 3.5mm Stereo Headphone Output, RJ-45 Connector (Ethernet), RCA L/R Input, RCA L/R Output, SPDIF (Toslink) Output, DC In
Buttons Front Power (Standby)
Buttons Rear WPS Button
LEDs One Blue LED indicating unit is ON. One orange LED will indicate STANDBY. On Connection to the Network, Blue LED will blink. On no power application, no LED.
Power supply 100-240Vac, 0.6A, 50-60Hz; o/p: 5Vdc, 3A
Cables Ethernet Cable, 6’ RCA Stereo Audio Cables
Output Sample Rates 8.0 kHz, 11.05 kHz, 12.0 kHz, 16.0 kHz, 22.05 kHz, 24.0 kHz, 32.0 kHz, 44.1 kHz, 48.0 kHz
Audio Codecs w/ Input bitrates
MPEG-1 Audio Layer 3 (MP3) 32, 40, 48, 56, 64, 80, 96, 112, 128, 144, 160, 192, 224, 256 and 320 kbit/s
AAC-LC 64, 96, 126, 256, and 320 kbits.
WMA9 64 to 192 kbit/s
WAV Bitrates from 16kbit (8 kHz Mono) to 1.92 mbit (48 kHz Stereo) Containers Supported MP4 containing AAC-LC media. M4A containing AAC-LC media. ASF containing WMA9 media
Model DMP100 · Detachable (y/n) N

Warranty Information
of a third party’s service for which this product’s use or operation may require.
TO THE EXTENT NOT PROHIBITED BY LAW, ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary by jurisdiction.
Linksys warrants this Linksys hardware product against defects in materials and workmanship under normal use for the Warranty Period, which begins on the date of purchase by the original end-user purchaser and lasts for the period specified below:
This limited warranty is non-transferable and extends only to the original end-user purchaser. Your exclusive remedy and Linksys’ entire liability under this limited warranty will be for Linksys, at its option, to (a) repair the product with new or refurbished parts, (b) replace the product with a reasonably available equivalent new or refurbished Linksys product, or (c) refund the purchase price of the product less any rebates. Any repaired or replacement products will be warranted for the remainder of the original Warranty Period or thirty (30) days, whichever is longer. All products and parts that are replaced become the property of Linksys.
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this limited warranty fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This limited warranty does not apply if: (a) the product assembly seal has been removed or damaged, (b) the product has been altered or modified, except by Linksys, (c) the product damage was caused by use with non‑Linksys products, (d) the product has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, (e) the product has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident, (f) the serial number on the Product has been altered, defaced, or removed, or (g) the product is supplied or licensed for beta, evaluation, testing or demonstration purposes for which Linksys does not charge a purchase price or license fee.
If you have a question about your product or experience a problem with it, please go to www.linksysbycisco.com/ support where you will find a variety of online support tools and information to assist you with your product. If the product proves defective during the Warranty Period, contact Linksys Technical Support for instructions on how to obtain warranty service. The telephone number for Linksys Technical Support in your area can be found in the product User Guide and at www.linksysbycisco.com. Have your product serial number and proof of purchase on hand when calling. A DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED TO PROCESS WARRANTY CLAIMS. If you are requested to return your product, you will be given a Return Materials Authorization (RMA) number. You are responsible for properly packaging and shipping your product to Linksys at your cost and risk. You must include the RMA number and a copy of your dated proof of original purchase when returning your product. Products received without a RMA number and dated proof of original purchase will be rejected. Do not include any other items with the product you are returning to Linksys. Defective product covered by this limited warranty will be repaired or replaced and returned to you without charge.
ALL SOFTWARE PROVIDED BY LINKSYS WITH THE PRODUCT, WHETHER FACTORY LOADED ON THE PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING THE PRODUCT, IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND. Without limiting the foregoing, Linksys does not warrant that the operation of the product or software will be uninterrupted or error free. Also, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the product, software or any equipment, system or network on which the product or software is used will be free of vulnerability to intrusion or attack. The product may include or be bundled with third party software or service offerings. This limited warranty shall not apply to such third party software or service offerings. This limited warranty does not guarantee any continued availability

Customers outside of the United States of America and Canada are responsible for all shipping and handling charges, custom duties, VAT and other associated taxes and charges. Repairs or replacements not covered under this limited warranty will be subject to charge at Linksys’ then-current rates.
This limited warranty is neither a service nor a support contract. Information about Linksys’ current technical support offerings and policies (including any fees for support services) can be found at: www.linksysbycisco.com/support.
This limited warranty is governed by the laws of the jurisdiction in which the Product was purchased by you.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.

Regulatory Information
Australian RF Exposure Statement
Safety Warning Statement
DMP100 player with Dipole type antenna and maximum antenna gain is 3.5dBi in 5 GHz band and 1.5dBi in 2.4GHz band.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna.
This equipment is in conformity with the IC radiation exposure limits set forth for an uncontrolled environment. This device must be installed and used at a distance of at least 20 cm (8 in) between the antenna and the body of the user. The transmitter should not be placed close to another antenna or another transmitter, or to function with another antenna or another transmitter.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Cet appareil numérique est conforme aux limites établies par IC en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d’au moins 20 cm (8 in) entre l’antenne et le corps de l’utilisateur. L’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur.
For operation within 5.150-5.250 GHz frequency range, it is restricted to indoor environment. The availability of some specific and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.

IC Class B Statement (Canada)
This class B digital device complies with Industry Canada ICES-003 and RSS-210 rules.
Operation is subject to the following two conditions
This device may not cause interference and 1.
This device must accept any interference, including 2. interference that may cause undesired operation of the device
This device has been designed to operate with an antenna having a maximum gain of 3.5dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
CE marking on this product represents the product is in compliance with all directives that are applicable to it.
EU Declaration of conformity (DOC)
This product complies with the essential requirements of the EMC Directive 2004/108/EC, the Low Voltage Directive 2006/95/EC and the R&TTE Directive 1999/5/EC. For more detail, Please see the DoC.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 et RSS-210 d’industrie.
L’opération est sujette aux deux conditions suivantes :
Ceci le dispositif peut ne pas causer l’interférence et 1.
Ceci le dispositif doit accepter n’importe quelle 2. interférence, y compris l’interférence qui peut causer fonctionnement peu désiré du dispositif.
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximum du dBi 3.5 L’antenne ayant un gain plus élevé est strictement interdite par règlements d’industrie Canada. L’impédance exigée d’antenne est de 50 ohms.
R&TTE Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. Compliance Information for 2.4-GHz and 5-GHz Wireless Products Relevant to the EU and Other Countries Following the EU Directive1999/5/ EC (R&TTE Directive).The following standards were applied during the assessment of the product against the requirements of the R&TTE Directive:
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co- channel mobile satellite systems;
The maximum antenna gain 3.5dBi permitted (for devices in the band 5250 - 5350 MHz and 5470 - 5725 MHz ) to comply with the e.i.r.p. limit ; and the maximum antenna gain 3dBi permitted (for devices in the band 5725-5825 MHz) to comply with the e.i.r.p. limits specified for point- to-point and non point-to-point operation as appropriate, as stated in section A9.2(3).
The DMP100 Player has disabled the 5600-5650M band by S/W to avoid 5600-5650M band for IC certification.

Ez a készülék teljesíti az alapvető követelményeket és más 1999/5/EK irányelvben meghatározott vonatkozó rendelkezéseket.
Това оборудване отговаря на съществените изисквания и приложими клаузи на Директива 1999/5/ЕС.
Magyar [Hungarian]:
Toto zařízení je v souladu se základními požadavky a ostatními odpovídajícími ustanoveními Směrnice 1999/5/EC.
Česky [Czech]:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-direktiv 1999/5/EF.
Norsk [Norwegian]:
Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Direktiv 1999/5/EF.
Dansk [Danish]:
Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi Dyrektywą UE: 1999/5/EC.
Polski [Polish]:
Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden Vorgaben der Richtlinie 1999/5/EU.
Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.
Deutsch [German]:
Português [Portuguese]:
Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale Directivei 1999/5/EC.
See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.
Eesti [Estonian]:
This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.
Slovensko [Slovenian]:
English:
Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív: 1999/5/EC.
Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva 1999/5/CE.
Slovensky [Slovak]:
Español [Spanish]:
Tämä laite täyttää direktiivin 1999/5/EY olennaiset vaatimukset ja on siinä asetettujen muiden laitetta koskevien määräysten mukainen.
Αυτός ο εξοπλισµός είναι σε συµµόρφωση µε τις ουσιώδεις απαιτήσεις και άλλες σχετικές διατάξεις της Οδηγίας 1999/5/EC.
Ελληνική [Greek]:
Suomi [Finnish]:
Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la Directive 1999/5/EC.
Français [French]:
Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC.
Svenska [Swedish]:
Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.
Íslenska [Icelandic]:
Alert sign! Follows CE marking
Alert sign must be indicated if a restriction on use applied to the product and it must follow the CE marking.
Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/CE.
Italiano [Italian]:
NB-Identification number (if there is any)
Šī iekārta atbilst Direktīvas 1999/5/ EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Latviski [Latvian]:
Notified body number is indicated if it is involved in the conformity assessment procedure.
Šis įrenginys tenkina 1999/5/EB Direktyvos esminius reikalavimus ir kitas šios direktyvos nuostatas.
Lietuvių [Lithuanian]:
Please check the CE mark on the product label to find out which notified body was involved during assessment.
Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1999/5/EC.
Nederlands [Dutch]:
In the majority of the EU and other European countries, the 2.4 GHz and the 5.0 GHz bands have been made available for the use of wireless local area networks (LANs). The table labeled “Overview of Regulatory Requirements for Wireless LANs” provides an overview of the regulatory requirements applicable for the 2.4 GHz and the 5.0 GHz bands.
Dan l-apparat huwa konformi mal-ħtiġiet essenzjali u l-provedimenti l-oħra rilevanti tad-Direttiva 1999/5/EC.
Malti [Maltese]:
Български [Bulgarian] · Română [Romanian] · National Restrictions

The requirements for any country may evolve. Linksys recommends that end-user check with the local authorities for the latest status of their national regulations for both the 2.4 GHz and the 5.0 GHz.
In Denmark, the band 5150-5350 MHz is also allowed for outdoor usage.
Overview of Regulatory Requirements for Wireless Table B–
In Italy, if used outside of own premises, “general authorization” is required within the band 5150-5350 MHz & 5470-5725 MHz. For detailed information on applying for license, the end-user should contact the national spectrum authorities in Italy or visit http://www.comunicazioni.it/it/
Max. Power
Latvia
5150-5250 200 X
In Latvia, outdoor usage of the 2,4 GHz band requires an authorization from the Electronic Communications Office. For detailed information, please visit http://www.esd.lv
5470-5725† 1000 X
Dynamic Frequency Selection (DFS) and Transmit Power Control †† (TCP) are required in the frequency ranges of 5250-5350 MHz and 5470-5725 MHz.
Although Norway, Switzerland and Liechtenstein are not EU 1. member states, the EU Directive 1999/5/EC has also been implemented in those countries.
Dynamic Frequency Selection (DFS) and Transmit Power Control (TPC) are required for operation in the 5.0 GHz band.
The regulatory limits for maximum output power are 2. specified in EIRP. The EIRP level of a device can be calculated by adding the gain of the antenna used (specified in dBi) to the output power available at the connector (specified in dBm).
DFS: This function is required by the national regulations to avoid interference with the Radio Location Services (radars) when operating in the 5.250-5.350 GHz & 5.470-5.725 GHz bands.
This device operates in a client mode without radar detection capability. The client software and associated drivers will not initiate any transmission in the DFS frequencies during the presence of radar.
The use of software or firmware not supported/provided by Linksys may result that the equipment is no longer compliant with the regulatory requirements.
TPC: For operation in the 5.0 GHz band, the maximum power level is 3 dB or more below the applicable limit. As such, TPC is not required.
This product contains a wireless-N, -G, -B, and/or –A transceiver, intended for use in all EU countries, and all other countries following EU directive 1999/5/EC, without any limitation except for any country listed in the restriction of use below:
Follow these steps to access technical documents:
Enter 1. http://www.linksysbycisco.com/international in your web browser.
Ce produit contient un sans fil-N, - G, - B, et/ou - A émetteur récepteur, destiné à l’utilisation dans tous les pays de l’UE, et tous autres pays après l’UE 1999/5/EC directif, sans n’importe quelle limitation excepté n’importe quel pays énuméré dans la restriction de l’utilisation ci-dessous :
Select the country or region in which you live. 2.
Click the 3. Products tab.
Dieses Produkt enthält ein drahtloses-n, - G, - ein B und/ oder - ein Lautsprecherempfänger, bestimmt für Gebrauch in allen EU-Ländern und in allen weiteren Ländern nach EU richtungweisendes 1999/5/EC, ohne irgendeine Beschränkung außer jedem möglichem Land, das nachstehend in der Beschränkung des Gebrauches aufgeführt wird:
Select the appropriate product category. 4.
Select the product sub-category, if necessary. 5.
Select the product. 6.
Select the type of documentation you want from the 7. More Information section. The document will open in PDF format if you have Adobe Acrobat installed on your computer.
Cer produit zahlt contient un sans fil-N, - G, - B, et/ou - ein émetteur récepteur, destiné à l’utilisation dans tous les de L’UE, und zahlt tous autres après l’UE 1999/5/EC directif, sans, n’importe quelle Beschränkung excepté n’importe, das quel énuméré dans la restriction de L’utilisation Ci-dessous zahlt:
In Croatia, license is required in the band 5150-5350 MHz.
In France, outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz. For detailed information, the end-user should contact the national spectrum authority in France or visit http://www.arcep.fr/

2002/96/EC on Waste Electric and Electronic Equipment (WEEE)
Ceština (Czech) - Informace o ochraně životního prostředí pro zákazníky v zemích Evropské unie Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené tímto symbolem na produktu anebo na obalu bylo likvidováno s netříděným komunálním odpadem. Tento symbol udává, že daný produkt musí být likvidován odděleně od běžného komunálního odpadu. Odpovídáte za likvidaci tohoto produktu a dalších elektrických a elektronických zařízení prostřednictvím určených sběrných míst stanovených vládou nebo místními úřady. Správná likvidace a recyklace pomáhá předcházet potenciálním negativním dopadům na životní prostředí a lidské zdraví. Podrobnější informace o likvidaci starého vybavení si laskavě vyžádejte od místních úřadů, podniku zabývajícího se likvidací komunálních odpadů nebo obchodu, kde jste produkt zakoupili.
This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:
Dansk (Danish) - Miljøinformation for kunder i EU EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol
English - Environmental Information for Customers in the European Union European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
på produktet og/eller emballagen ikke må bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald. Det er dit ansvar at bortskaffe dette og andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de lokale myndigheder. Korrekt bortskaffelse og genvinding vil hjælpe med til at undgå mulige skader for miljøet og menneskers sundhed. Kontakt venligst de lokale myndigheder, renovationstjenesten eller den butik, hvor du har købt produktet, angående mere detaljeret information om bortskaffelse af dit gamle udstyr.
Deutsch (German) - Umweltinformation für Kunden innerhalb der Europäischen Union Die Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist , nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.
Български (Bulgarian) - Информация относно опазването на околната среда за потребители в Европейския съюз Европейска директива 2002/96/EC изисква уредите, носещи този символ върху изделието и/или опаковката му, да не се изхвърля т с несортирани битови отпадъци. Символът обозначава, че изделието трябва да се изхвърля отделно от сметосъбирането на обикновените битови отпадъци. Ваша е отговорността този и другите електрически и електронни уреди да се изхвърлят в предварително определени от държавните или общински органи специализирани пунктове за събиране. Правилното изхвърляне и рециклиране ще спомогнат да се предотвратят евентуални вредни за околната среда и здравето на населението последствия. За по-подробна информация относно изхвърлянето на вашите стари уреди се обърнете към местните власти, службите за сметосъбиране или магазина, от който сте закупили уреда.

Eesti (Estonian) - Keskkonnaalane informatsioon Euroopa Liidus asuvatele klientidele Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on seadmeid, millel on tootel või pakendil käesolev sümbol , keelatud kõrvaldada koos sorteerimata olmejäätmetega. See sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike ametiasutuste poolt ette nähtud kogumispunktide kaudu. Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida võimalikke negatiivseid tagajärgi keskkonnale ning inimeste tervisele. Vanade seadmete kõrvaldamise kohta täpsema informatsiooni saamiseks võtke palun ühendust kohalike ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te toote ostsite.
Français (French) - Informations environnementales pour les clients de l’Union européenne La directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.
Español (Spanish) - Información medioambiental para clientes de la Unión Europea La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.
Italiano (Italian) - Informazioni relative all’ambiente per i clienti residenti nell’Unione Europea La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.
ξλληνικά (Greek) - Στοιχεία περιβαλλοντικής προστασίας για πελάτες εντός της Ευρωπαϊκής Ένωσης Η Κοινοτική Οδηγία 2002/96/EC απαιτεί ότι ο εξοπλισμός ο οποίος φέρει αυτό το σύμβολο στο προϊόν και/ή στη συσκευασία του δεν πρέπει να απορρίπτεται μαζί με τα μικτά κοινοτικά απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων οι οποίες παρέχονται από το κράτος ή τις αρμόδιες τοπικές αρχές. Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη πιθανών αρνητικών συνεπειών για το περιβάλλον και την υγεία. Για περισσότερες πληροφορίες σχετικά με την απόρριψη του παλιού σας εξοπλισμού, παρακαλώ επικοινωνήστε με τις τοπικές αρχές, τις υπηρεσίες απόρριψης ή το κατάστημα από το οποίο αγοράσατε το προϊόν.
Latviešu valoda (Latvian) - Ekoloģiska informācija klientiem Eiropas Savienības jurisdikcijā Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst izmest nešķirotā veidā kopā ar komunālajiem atkritumiem (tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo un citas elektriskas un elektroniskas ierīces izmest atkritumos, izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos un pārstrāde tiek veikta pareizi, tad mazinās iespējamais kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā, kur iegādājāties šo izstrādājumu.

Lietuvškai (Lithuanian) - Aplinkosaugos informacija, skirta Europos Sąjungos vartotojams Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį), negalima šalinti kartu su nerūšiuotomis komunalinėmis atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad ši ir kita elektros ar elektroninė įranga būtų šalinama per tam tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose įsigijote tą gaminį.
Nederlands (Dutch) - Milieu-informatie voor klanten in de Europese Unie De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit symbool op het product of de verpakking, niet mag worden ingezameld met niet-gescheiden huishoudelijk afval. Dit symbool geeft aan dat het product apart moet worden ingezameld. U bent zelf verantwoordelijk voor de vernietiging van deze en andere elektrische en elektronische apparatuur via de daarvoor door de landelijke of plaatselijke overheid aangewezen inzamelingskanalen. De juiste vernietiging en recycling van deze apparatuur voorkomt mogelijke negatieve gevolgen voor het milieu en de gezondheid. Voor meer informatie over het vernietigen van uw oude apparatuur neemt u contact op met de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft.
Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti fl-Unjoni Ewropea Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih is-simbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika li dan il-prodott għandu jintrema separatament minn ma’ l-iskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew il-ħanut minn fejn xtrajt il-prodott.
Norsk (Norwegian) - Miljøinformasjon for kunder i EU EU-direktiv 2002/96/EF krever at utstyr med følgende symbol
avbildet på produktet og/eller pakningen, ikke må kastes sammen med usortert avfall. Symbolet indikerer at dette produktet skal håndteres atskilt fra ordinær avfallsinnsamling for husholdningsavfall. Det er ditt ansvar å kvitte deg med dette produktet og annet elektrisk og elektronisk avfall via egne innsamlingsordninger slik myndighetene eller kommunene bestemmer. Korrekt avfallshåndtering og gjenvinning vil være med på å forhindre mulige negative konsekvenser for miljø og helse. For nærmere informasjon om håndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon for avfall eller butikken der du kjøpte produktet.
Magyar (Hungarian) - Környezetvédelmi információ az európai uniós vásárlók számára A 2002/96/EC számú európai uniós irányelv megkívánja, hogy azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott termék kidobásakor a szokványos háztartási hulladékelszállítási rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön felelõssége, hogy ezt, és más elektromos és elektronikus berendezéseit a kormányzati vagy a helyi hatóságok által kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ hulladékfeldolgozás segít a környezetre és az emberi egészségre potenciálisan ártalmas negatív hatások megelõzésében. Ha elavult berendezéseinek felszámolásához további részletes információra van szüksége, kérjük, lépjen kapcsolatba a helyi hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal üzlettel, ahol a terméket vásárolta.
Polski (Polish) - Informacja dla klientów w Unii Europejskiej o przepisach dotyczących ochrony środowiska Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt oznaczony symbolem znajdującym się na produkcie i/lub jego opakowaniu nie był wyrzucany razem z innymi niesortowanymi odpadami komunalnymi. Symbol ten wskazuje, że produkt nie powinien być usuwany razem ze zwykłymi odpadami z gospodarstw domowych. Na Państwu spoczywa obowiązek wyrzucania tego i innych urządzeń elektrycznych oraz elektronicznych w punktach odbioru wyznaczonych przez władze krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób i jego recykling pomogą zapobiec potencjalnie negatywnym konsekwencjom dla środowiska i zdrowia ludzkiego. W celu uzyskania szczegółowych informacji o usuwaniu starego sprzętu, prosimy zwrócić się do lokalnych władz, służb oczyszczania miasta lub sklepu, w którym produkt został nabyty.

Português (Portuguese) - Informação ambiental para clientes da União Europeia A Directiva Europeia 2002/96/CE exige que o equipamento que exibe este símbolo no produto e/ou na sua embalagem não seja eliminado junto com os resíduos municipais não separados. O símbolo indica que este produto deve ser eliminado separadamente dos resíduos domésticos regulares. É da sua responsabilidade eliminar este e qualquer outro equipamento eléctrico e electrónico através das instalações de recolha designadas pelas autoridades governamentais ou locais. A eliminação e reciclagem correctas ajudarão a prevenir as consequências negativas para o ambiente e para a saúde humana. Para obter informações mais detalhadas sobre a forma de eliminar o seu equipamento antigo, contacte as autoridades locais, os serviços de eliminação de resíduos ou o estabelecimento comercial onde adquiriu o produto.
Slovenčina (Slovene) - Okoljske informacije za stranke v Evropski uniji Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme, označene s tem simbolom – na izdelku in/ali na embalaži – med običajne, nerazvrščene odpadke. Ta simbol opozarja, da je treba izdelek odvreči ločeno od preostalih gospodinjskih odpadkov. Vaša odgovornost je, da to in preostalo električno in elektronsko opremo odnesete na posebna zbirališča, ki jih določijo državne ustanove ali lokalna uprava. S pravilnim odlaganjem in recikliranjem boste preprečili morebitne škodljive vplive na okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare opreme, se obrnite na lokalno upravo, odpad ali trgovino, kjer ste izdelek kupili.
Suomi (Finnish) - Ympäristöä koskevia tietoja EU- alueen asiakkaille EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoa ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana. Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet viemällä tuote tai tuotteet viranomaisten määräämään keräyspisteeseen. Laitteiston oikea hävittäminen estää mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä myymälästä, josta ostit tuotteen.
Română (Romanian) - Informaţii de mediu pentru clienţii din Uniunea Europeană Directiva europeană 2002/96/CE impune ca echipamentele care prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să nu fie casate împreună cu gunoiul menajer municipal. Simbolul indică faptul că acest produs trebuie să fie casat separat de gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi acest produs şi alte echipamente electrice şi electronice prin intermediul unităţilor de colectare special desemnate de guvern sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta la prevenirea potenţialelor consecinţe negative asupra sănătăţii mediului şi a oamenilor. Pentru mai multe informaţii detaliate cu privire la casarea acestui echipament vechi, contactaţi autorităţile locale, serviciul de salubrizare sau magazinul de la care aţi achiziţionat produsul.
Svenska (Swedish) - Miljöinformation för kunder i Europeiska unionen Det europeiska direktivet 2002/96/EC kräver att utrustning med denna symbol på produkten och/eller förpackningen inte får kastas med osorterat kommunalt avfall. Symbolen visar att denna produkt bör kastas efter att den avskiljts från vanligt hushållsavfall. Det faller på ditt ansvar att kasta denna och annan elektrisk och elektronisk utrustning på fastställda insamlingsplatser utsedda av regeringen eller lokala myndigheter. Korrekt kassering och återvinning skyddar mot eventuella negativa konsekvenser för miljön och personhälsa. För mer detaljerad information om kassering av din gamla utrustning kontaktar du dina lokala myndigheter, avfallshanteringen eller butiken där du köpte produkten.
Slovenčina (Slovak) - Informácie o ochrane životného prostredia pre zákazníkov v Európskej únii Podľa európskej smernice 2002/96/ES zariadenie s týmto symbolom na produkte a/alebo jeho balení nesmie byť likvidované spolu s netriedeným komunálnym odpadom. Symbol znamená, že produkt by sa mal likvidovať oddelene od bežného odpadu z domácností. Je vašou povinnosťou likvidovať toto i ostatné elektrické a elektronické zariadenia prostredníctvom špecializovaných zberných zariadení určených vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia pomôže zabrániť prípadným negatívnym dopadom na životné prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie informácie o likvidácii starého zariadenia, obráťte sa, prosím, na miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov alebo obchod, v ktorom ste si produkt zakúpili.

Software License Agreement
SYSTEMS-LINKSYS (ASIA) PTE LTD. OR CISCO-LINKSYS K.K. (“LINKSYS”) LICENSING THE SOFTWARE INSTEAD OF CISCO-LINKSYS LLC. BY DOWNLOADING OR INSTALLING THE SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO THE RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.
This product from Cisco-Linksys LLC or from one of its affiliates Cisco Systems-Linksys (Asia) Pte Ltd. or Cisco- Linksys K.K. (“Linksys”) contains software (including firmware) originating from Linksys and its suppliers and may also contain software from the open source community. Any software originating from Linksys and its suppliers is licensed under the Linksys Software License Agreement contained at Schedule 1 below. You may also be prompted to review and accept that Linksys Software License Agreement upon installation of the software.
License. Subject to the terms and conditions of this Agreement, Linksys grants the original end user purchaser of the Linksys product containing the Software (“You”) a nonexclusive license to use the Software solely as embedded in or (where authorized in the applicable documentation) for communication with such product. This license may not be sublicensed, and is not transferable except to a person or entity to which you transfer ownership of the complete Linksys product containing the Software, provided you permanently transfer all rights under this Agreement and do not retain any full or partial copies of the Software, and the recipient agrees to the terms of this Agreement.
Any software from the open source community is licensed under the specific license terms applicable to that software made available by Linksys at www.linksysbycisco.com/ gpl or as provided for in Schedules 2 and 3 below.
Where such specific license terms entitle you to the source code of such software, that source code is upon request available at cost from Linksys for at least three years from the purchase date of this product and may also be available for download from www.linksysbycisco.com/ gpl. For detailed license terms and additional information on open source software in Linksys products please look at the Linksys public web site at: www.linksysbycisco. com/gpl/ or Schedule 2 below as applicable.
“Software” includes, and this Agreement will apply to (a) the software of Linksys or its suppliers provided in or with the applicable Linksys product, and (b) any upgrades, updates, bug fixes or modified versions (“Upgrades”) or backup copies of the Software supplied to You by Linksys or an authorized reseller, provided you already hold a valid license to the original software and have paid any applicable fee for the Upgrade.
BY DOWNLOADING OR INSTALLING THE SOFTWARE, OR USING THE PRODUCT CONTAINING THE SOFTWARE, YOU ARE CONSENTING TO BE BOUND BY THE SOFTWARE LICENSE AGREEMENTS BELOW. IF YOU DO NOT AGREE TO ALL OF THESE TERMS, THEN YOU MAY NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR, IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO THE RETURN PROCESS AND POLICIES OF THE PARTY FROM WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.
Protection of Information. The Software and documentation contain trade secrets and/or copyrighted materials of Linksys or its suppliers. You will not copy or modify the Software or decompile, decrypt, reverse engineer or disassemble the Software (except to the extent expressly permitted by law notwithstanding this provision), and You will not disclose or make available such trade secrets or copyrighted material in any form to any third party. Title to and ownership of the Software and documentation and any portion thereof, will remain solely with Linksys or its suppliers.
The software Licenses applicable to software from Linksys are made available at the Linksys public web site at: www.linksysbycisco.com and www.linksysbycisco. com/gpl/ respectively. For your convenience of reference, a copy of the Linksys Software License Agreement and the main open source code licenses used by Linksys in its products are contained in the Schedules below.
Collection and Processing of Information. You agree that Linksys and/or its affiliates may, from time to time, collect and process information about your Linksys product and/ or the Software and/or your use of either in order (i) to enable Linksys to offer you Upgrades; (ii) to ensure that your Linksys product and/or the Software is being used in accordance with the terms of this Agreement; (iii) to provide improvements to the way Linksys delivers technology to you and to other Linksys customers; (iv) to enable Linksys to comply with the terms of any agreements it has with
THIS LICENSE AGREEMENT IS BETWEEN YOU AND CISCO-LINKSYS LLC OR ONE OF ITS AFFILIATES CISCO

any third parties regarding your Linksys product and/or Software and/or (v) to enable Linksys to comply with all applicable laws and/or regulations, or the requirements of any regulatory authority or government agency. Linksys and/ or its affiliates may collect and process this information provided that it does not identify you personally. Your use of your Linksys product and/or the Software constitutes this consent by you to Linksys and/ or its affiliates’ collection and use of such information and, for EEA customers, to the transfer of such information to a location outside the EEA.
FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.
Export. Software, including technical data, may be subject to U.S. export control laws and regulations and/or export or import regulations in other countries. You agree to comply strictly with all such laws and regulations.
U.S. Government Users. The Software and documentation qualify as “commercial items” as defined at 48 C.F.R. 2.101 and 48 C.F.R. 12.212. All Government users acquire the Software and documentation with only those rights herein that apply to non-governmental customers.
Software Upgrades etc. If the Software enables you to receive Upgrades, you may elect at any time to receive these Upgrades either automatically or manually. If you elect to receive Upgrades manually or you otherwise elect not to receive or be notified of any Upgrades, you may expose your Linksys product and/or the Software to serious security threats and/or some features within your Linksys product and/or Software may become inaccessible. There may be circumstances where we apply an Upgrade automatically in order to comply with changes in legislation, legal or regulatory requirements or as a result of requirements to comply with the terms of any agreements Linksys has with any third parties regarding your Linksys product and/or the Software. You will always be notified of any Upgrades being delivered to you. The terms of this license will apply to any such Upgrade unless the Upgrade in question is accompanied by a separate license, in which event the terms of that license will apply.
General Terms. This Agreement will be governed by and construed in accordance with the laws of the State of California, without reference to conflict of laws principles. The United Nations Convention on Contracts for the International Sale of Goods will not apply. If any portion of this Agreement is found to be void or unenforceable, the remaining provisions will remain in full force and effect. This Agreement constitutes the entire agreement between the parties with respect to the Software and supersedes any conflicting or additional terms contained in any purchase order or elsewhere.
Schedule 2
Open Source Software. The GPL or other open source code incorporated into the Software and the open source license for such source code are available for free download at http://www.linksysbycisco.com/gpl. If You would like a copy of the GPL or other open source code in this Software on a CD, Linksys will mail to You a CD with such code for $9.99 plus the cost of shipping, upon request.
If this Linksys product contains open source software licensed under Version 2 of the “GNU General Public License” then the license terms below in this Schedule 2 will apply to that open source software. The license terms below in this Schedule 2 are from the public web site at http://www.gnu.org/copyleft/gpl.html
Term and Termination. You may terminate this License at any time by destroying all copies of the Software and documentation. Your rights under this License will terminate immediately without notice from Linksys if You fail to comply with any provision of this Agreement.
Version 2, June 1991
Copyright © 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA
Limited Warranty. The warranty terms and period specified in the applicable Linksys Product User Guide shall also apply to the Software.
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Disclaimer of Liabilities. IN NO EVENT WILL LINKSYS OR ITS SUPPLIERS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF CAUSE (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software–to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors
Preamble

commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.
This License applies to any program or other work 0. which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/ or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
You may copy and distribute verbatim copies of the 1. Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.
You may modify your copy or copies of the Program 2. or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:
The precise terms and conditions for copying, distribution and modification follow.
You must cause the modified files to carry a.
prominent notices stating that you changed the files and the date of any change.
You must cause any work that you distribute or b.
publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.

If the modified program normally reads commands c.
Accompany it with the information you received as c.
interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)
to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
You may not copy, modify, sublicense, or distribute 4. the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
You may copy and distribute the Program (or a 3. work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:
You are not required to accept this License, since you 5. have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
Accompany it with the complete corresponding a.
machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
Accompany it with a written offer, valid for at least b.
Each time you redistribute the Program (or any work 6. based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.
three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,

If, as a consequence of a court judgment or allegation 7. of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
not specify a version number of this License, you may choose any version ever published by the Free Software Foundation.
If you wish to incorporate parts of the Program into 10. other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, 11. THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR 12. AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
If the distribution and/or use of the Program is 8. restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
END OF SCHEDULE 2
The Free Software Foundation may publish revised 9. and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
If this Linksys product contains open source software licensed under the OpenSSL license:
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/).
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does
This product includes cryptographic software written by Eric Young (eay@cryptsoft.com).

This product includes software written by Tim Hudson (tjh@cryptsoft.com).
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
In addition, if this Linksys product contains open source software licensed under the OpenSSL license then the license terms below in this Schedule 3 will apply to that open source software. The license terms below in this Schedule 3 are from the public web site at http://www.openssl.org/source/license.html.
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues related to OpenSSL please contact openssl-core@openssl.org.
This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com).
Copyright © 1995-1998 Eric Young (eay@cryptsoft.com) All rights reserved.
Copyright © 1998-2007 The OpenSSL Project. All rights reserved.
This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
The implementation was written so as to conform with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following conditions are adhered to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft. com).
Redistributions of source code must retain the above 1. copyright notice, this list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the 2. above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
All advertising materials mentioning features or 3. use of this software must display the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed.
If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.
The names “OpenSSL Toolkit” and “OpenSSL Project” 4. must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact openssl-core@openssl.org.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
Products derived from this software may not be called 5. “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project.
Redistributions of source code must retain the 1. copyright notice, this list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the 2. above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Redistributions of any form whatsoever must retain 6. the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”
All advertising materials mentioning features or 3. use of this software must display the following acknowledgement:
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
“This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)”

The word ‘cryptographic’ can be left out if the routines from the library being used are not cryptographic related.
If you include any Windows specific code (or a derivative 4. thereof) from the apps directory (application code) you must include an acknowledgement: “This product includes software written by Tim Hudson (tjh@ cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS’’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The license and distribution terms for any publicly available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution license [including the GNU Public License.]
9010210NC-RR
Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.