EN
Lindy logo
Official user manual

Lindy 32825

32 pages·256 KB·Computer Hardware·PDF·ENNLJA
Lindy 32825
Table of Contents 10 sections CPU Switch LITE USB 2.0 2 Port, No. 32825 · CPU Switch LITE USB 2.0 · 4 Port, No. 32826 · www. LINDY .com · … ShowHide
Page 1 of the Lindy 32825 user manual — CPU Switch LITE USB 2.0 2 Port, No. 32825
Page 1 · click to enlarge
Page 1
Lindy 32825 — CPU Switch LITE USB 2.0 2 Port, No. 32825 diagram (page 1)
Fig. 1 · CPU Switch LITE USB 2.0 2 Port, No. 32825

CPU Switch LITE USB 2.0 User Manual English Benutzerhandbuch Deutsch Manuel Utilisateur Français Manuale d’uso Italiano

Lindy 32825 — CPU Switch LITE USB 2.0 2 Port, No. 32825 diagram (page 1)
Fig. 2 · CPU Switch LITE USB 2.0 2 Port, No. 32825
Lindy 32825 — CPU Switch LITE USB 2.0 2 Port, No. 32825 diagram (page 1)
Fig. 3 · CPU Switch LITE USB 2.0 2 Port, No. 32825
Lindy 32825 — CPU Switch LITE USB 2.0 2 Port, No. 32825 diagram (page 1)
Fig. 4 · CPU Switch LITE USB 2.0 2 Port, No. 32825

CPU Switch LITE USB 2.0 2 Port, No. 32825

CPU Switch LITE USB 2.0

4 Port, No. 32826

www. LINDY .com

For Home and Office Use Tested to Comply with FCC Standards

© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (MAY 2004)

Page 2 of the Lindy 32825 user manual — CPU Switch LITE USB 2.0 2 Port, No. 32825
Page 2 · click to enlarge
Page 2
Page 2 of the Lindy 32825 user manual — CPU Switch LITE USB 2.0 2 Port, No. 32825
Page 3 of the Lindy 32825 user manual — Content
Page 3 · click to enlarge
Page 3

Content

This manual contains the following parts: A Quick Start Instructions B English Manual C German Manual / Deutsches Benutzerhandbuch D French Manual / Manuel en français E Italian Manual / Manuale in italiano F Technical Data and Compliance Statement

Page 4 of the Lindy 32825 user manual — before switching to the next port!
Page 4 · click to enlarge
Page 4

Quick Start Instructions

  • Make sure all the devices to be connected to the CPU Switch LITE USB 2.0 are turned off.
  • Connect the CPU Switch LITE USB 2.0 to the computers keyboards, monitors and mice.
  • USB devices are hot pluggable. Please always allow the connected computers to install their drivers completely

before switching to the next port!

  • Switch the monitor on first, then the computers.
  • Do not switch channels during boot up of the connected computers.
  • For operation you can change the computer ports by pressing the hotkey from your keyboard. To learn about the advanced hotkey switching possibilities of this

switch please read the manual.

Detailed information can be found under the Installation and Operation Sections of this manual.

Page 5 of the Lindy 32825 user manual — Quick Start Instructions
Page 5 · click to enlarge
Page 5

Overview The LINDY CPU Switch LITE USB 2.0 combines control of up to 4 computers from one PS/2 or USB keyboard, mouse and monitor, with the facility to share USB 2.0/1.1 devices. The unit requires no software installation. Any modern USB 2.0 enabled operating system will support both the switch and the USB hub. Simply connect the cables and turn on the devices! CPU Switch function With the CPU Switch you can eliminate the cost of additional accessories, save valuable desk space and remove all of the problems associated with using multiple keyboards, monitors and mice. The CPU Switch LITE USB 2.0 provides flexible switching between the connected computers, using either the built-in button or PC keyboard hotkeys. Note: Keyboard hotkey switching is not supported when using USB Mac/Sun keyboards! USB Share function When using a PS/2 PC keyboard and mouse, the USB Share function allows USB devices to be switched independently from the ‘PS/2 + VGA’ part of the CPU Switch. This means you can switch keyboard, monitor and mouse from one computer whilst keeping the USB devices connected to the other. For example, you can print to a USB printer from PC 1, and then switch your keyboard, monitor and mouse to PC 2, leaving the USB printer still connected to PC 1. Restrictions when using 4D/5D and wireless mice, and extended multimedia keyboards The CPU Switch LITE USB 2.0 interprets and converts PS/2 to USB signals and then sends them via the USB bus to the attached computers. The official PS/2 to USB Conversion Standard does not define any proprietary function for mice with more than 3 buttons and 1 wheel. Also, it does not define a conversion standard for the additional keys of extended multimedia keyboards. Furthermore, there is no conversion standard for special wireless functions like battery status monitoring and RF device ID identification etc. The CPU Switch LITE USB 2.0 is not able to convert these special functions from PS/2 to USB, indeed these functions will not work with any current KVM switch which features PS/2 to USB conversion! Note: If you need these extra functions you can use USB mice and keyboards – but you will lose the advanced keyboard hotkey switching features, and some of the USB Share functionality!

Page 6 of the Lindy 32825 user manual — Features
Page 6 · click to enlarge
Page 6

Features

  • USB 2.0 specification compliant, backwards compatible with USB 1.1
  • Supports EHCI, UHCI, OHCI USB interface
  • Compatible with any widely used USB enabled operating system
  • Embedded USB hub to share different USB peripherals between all computers
  • LED port display for easy status monitoring
  • Beep sound when switching between computers
  • Auto scan function
  • Supports monitor resolution of up to 2048 x 1536 and high bandwidth over 250MHz
  • Supports DDC, DDC2, DDC2B
  • Bus powered (if used with self powered or low power USB devices) or self powered (requires power supply, not included) Package Contents
  • LINDY CPU Switch LITE USB 2.0, 2 Port or 4 Port model
  • 2 or 4 KVM combo cables USB 2.0 + VGA (depending on model)
  • This manual Installation

1. Before installation, please switch off all of the devices. 2. Connect the computers to the CPU Switch LITE USB 2.0 using the supplied 2m KVM USB 2.0 + VGA cables. 3. Connect either a PS/2 or USB keyboard and mouse, and a monitor to the sockets on the LINDY CPU Switch LITE USB 2.0. 4. The console port of the CPU Switch LITE USB 2.0 supports PS/2 or USB keyboards and mice, in any combination. 5. You can use a (self powered) USB 2.0 hub to connect extra USB devices. Power requirements / USB bus powered operation The CPU Switch LITE USB 2.0 can draw its power from either the connected computers or from an optional external 5V DC power supply (regulated voltage - an old style heavy power supply with a transformer may damage the connected USB devices and computers). When using the CPU Switch LITE 2.0 in USB bus power mode (without the optional power supply), you can connect low power USB devices (driving up to 100mA power from the USB bus), or self powered USB devices only! Tip: You can find the power requirement of any USB device which is connected to your PC by launching –

Windows Device Manager ►USB Controller ►USB Hubs ►Properties ►Power and then checking the ‘Power Required’ in the ‘Attached Devices’ box.

Page 7 of the Lindy 32825 user manual — ↑
Page 7 · click to enlarge
Page 7

For bus powered operation with low power USB devices attached, at least two computers should be connected, and be powered up. Bus powered operation also depends on the number of USB devices attached, and how much current they draw from the USB bus. Alternatively, you can attach a regulated 5V DC power supply to the CPU Switch LITE USB 2.0 or you can connect your USB devices via a self powered USB 2.0 hub. Operation To switch between the connected computers press the button on the CPU Switch LITE USB 2.0 or use a hotkey from your PC keyboard. Hotkey control (PC USB & PS/2 PC Keyboards only!) To send commands to the CPU Switch the key must be pressed twice within 2 seconds. This puts the CPU Switch into command mode. You will hear a beep for confirmation. Any further key presses must follow within another two seconds. If not, the CPU Switch exits from command mode and any further key presses are transferred to the selected computer. Note: Hotkey switching is available when using either a PS/2 or USB PC keyboard only! It is not available when using Mac and Sun keyboards! Advanced Hotkey control is only available when using a PS/2 PC keyboard! USB PC Keyboard Controls To switch USB Keyboard, Mouse, Monitor & USB devices (together) between computers Within 2 seconds + + = Previous Channel or + + = Next Channel Note: This is the only Hotkey control available when using USB PC Keyboards. For Advanced Hotkey control you must use a PS/2 PC keyboard! Advanced Hotkey Control (PS/2 PC Keyboards only!) To switch PS/2 Keyboard/Mouse, Monitor & USB devices (together) between computers Within 2 seconds + + = Previous Channel or + + = Next Channel Select PC port : + + = To select PC1 ~ PC2 or ~ PC4 directly

↑

↓

↑

↓

Port No. 1…2/4

Show 7 more labels / short text on this page
Scroll Lock · Scroll Lock · Scroll Lock · Scroll Lock · Scroll Lock · Scroll Lock · Scroll Lock
Page 8 of the Lindy 32825 user manual — B
Page 8 · click to enlarge
Page 8

To switch PS/2 Keyboard/Mouse & Monitor between computers (not USB devices) Within 2 seconds + + + = Previous Channel or + + + = Next Channel Select PC port : + + + = To select PC1 ~ PC2 or ~ PC4

↑

END

↓

END

Port No. 1…2/4

directly To switch USB devices only between computers Within 2 seconds + + + = Previous Channel or + + + = Next Channel Select PC port : + + + = To select PC1 ~ PC2 or ~ PC4

↑

↓

Port No. 1…2/4

directly To change Auto Scan Mode and Scan Interval

Scroll Lock Scroll Lock

S

+ + = Auto Scan. To get out of Auto Scan Mode,

Press any key or SPACE bar. OR + + = + any Number between 0-9 with: 1 = 10 seconds, 2 = 20 seconds, 3 = 30 seconds, 4 = 40 seconds, 5 = 50 seconds, 6 = 60 seconds, 7 = 70 seconds, 8 = 80 seconds, 9 = 90 seconds, 0 = 100 seconds The default Auto Scan Interval is 5 seconds at power on.

Scroll Lock Scroll Lock

S

The first command switches the console only into Scan mode. USB devices are not switched. It

works only when two computers are powered on at the same time. Exit Auto Scan Mode by pressing any key

To check beep function

+ + = Beeper , Check beep function is OK

Scroll Lock Scroll Lock

B

Show 10 more labels / short text on this page
Scroll Lock · Scroll Lock · Scroll Lock · Scroll Lock · Scroll Lock · Scroll Lock · Home · Scroll Lock · Scroll Lock · Home
Page 9 of the Lindy 32825 user manual — END
Page 9 · click to enlarge
Page 9

Keyboard Mapping for Mac & Sun Computers The following diagram shows the Hotkey combinations that emulate Mac and Sun keyboard commands. Note: This feature is only available on a PS/2 PC keyboard attached to the CPU Switch LITE USB 2.0. It is not available when using a USB keyboard! Example: Left Windows Key = L_Win

Sun Microsystems KeyboardWindows ps2 KeyboardMac OS StopL Win & L Alt Props_ _ L Win & L Ctrl Compose_ _ L Win & L Shift Front_ _ L Win & F1 Open_ L Win & F2 Find_ L Win & F3 Again_ L Win & F4 _ UndoL Win & F5 Copy_ L Win & F6 Paste_ L Win & F7 _ CutL Win & F8 _ HelpL Win & F11 _ PowerL Win & F12Power Mute_ L Win & "1" _ V DNL Win & "2" _ V UP_ L Win & "3" __ Windows KeyApple Key AltOption Print ScreenF13 Scroll LockF14 Pause BreakF15
Page 10 of the Lindy 32825 user manual — END
Page 10 · click to enlarge
Page 10

Troubleshooting If you experience any problems, first ensure that all cables are well seated and that both the mouse and keyboard have been correctly installed in each of the connected computers operating systems before connecting to the CPU Switch Lite USB 2.0. Tip: To avoid confusion label the cables with the number of each connected computer! PC Computers

  • Error Message: Keyboard or mouse are not found/not recognised during Boot-up. When connecting a PS/2 keyboard to the CPU Switch LITE USB 2.0’s PS/2 port, the computer fails to boot because of a keyboard error! The PC’s BIOS (Basic Input Output System) may need to be upgraded to so that it accepts USB to PS/2 conversion (normally most modern BIOS will support this). Check your PC/motherboard manufacturer’s web site for the latest BIOS version.
  • The keyboard or mouse is not working or not compatible with the PC! Please make sure the keyboard and/or mouse works correctly when plugged directly into each of the computers. If the problem persists, please try another keyboard or mouse. (Please also regard the restriction remarks on page 1 of this manual).
  • Mouse not working in Auto Scan mode! Press any key on the keyboard, or the button on the CPU Switch to return it to standard mode and then try the keyboard or mouse again.
  • About Auto Scan mode. When the CPU Switch LITE USB is in Auto Scan mode, each computers display is output to the monitor one by one. The USB Hub is not switched in auto scan mode! When you see the display of the computer you want to control, simply press a key and the console connects to that port.
  • What is the maximum recommended VGA cable length? The maximum recommended VGA cable length is 5m (20 feet).
  • What are the maximum recommended keyboard and mouse cable lengths? The recommended maximum keyboard and/or mouse cable length is 3m (10 feet).
  • What is the maximum recommended USB cable length? The maximum USB cable length is 5m (20 foot). If you experience problems using longer cable lengths, please use a USB Active Extension Cable. Please always regard the maximum USB cable segment length of 5m, and the maximum number of USB 2.0/1.1 segments.
  • When switching the USB Hub from one computer to another and there are many USB devices attached or shared, it will take about 10 seconds for all USB devices to be initialised.
Page 11 of the Lindy 32825 user manual — END
Page 11 · click to enlarge
Page 11

Sun Microsystems Computers If you use a Sun Microsystems computer with the CPU Switch LITE USB 2.0, you need to switch the console to the port connected to the Sun Microsystems computer before you boot up. After you finish booting the Sun, you can switch the console to the other computer ports. If you connect a USB PC keyboard to a USB hub port and a Sun Microsystems computer is connected to the CPU Switch LITE USB 2.0, then the keyboard will not work correctly as there is no Sun-to-PC keyboard mapping available. Sun-to-PC keyboard mapping is only available when using a PS/2 PC keyboard. You can connect a Sun USB keyboard to one of the USB hub ports. Note: Please note that most Hotkey switching functions are available from PS/2 PC keyboards only! Mac Computers If you connect a USB PC keyboard to a USB hub port and a Mac is connected to the CPU Switch LITE USB 2.0, then the keyboard will not work correctly as there is no Mac-to-PC keyboard mapping available. Mac-to-PC keyboard mapping is only available when using a PS/2 keyboard. You can connect a Mac keyboard to one of the USB hub ports.

Ask about the Lindy 32825

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lindy 32825

Be the first to ask — other owners or our team will answer.

Original document

Lindy 32825 manual PDF

32 pages·256 KB·Computer Hardware·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…