Instruction/ maintenance manual of the product IM468-A Lincoln Electric
Go to page of 16
K520 UTILITY C AR T OPERA TOR’S MANUAL IM468-A August, 2005 Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thought- ful operation on your part.
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
v v T ABLE OF CONTENTS Page Safety Precautions............................................................................................................. i - iv Product Description ....................................................................
A-1 UTILITY CART A-1 PRODUCT DESCRIPTION The K520 Utility Cart is designed for mounting and transporting the Lincoln family of small SP and Weld- Pak type welders and the small AC types. It has provi- sions for mounting a single gas cylinder when used with a SP type welder or Weld-Pak type.
A-2 A-2 FIGURE 2 STEP 4 (SEE FIGURE 3) With the Rear Shelf still raised, install the right hand Vertical Gusset alongside the Tank Support. Begin by placing the tab in the bottom of the Vertical Gusset into the slot in the Bottom Shelf, just to the right of the Rear Upright.
A-3 A-3 STEP 8 Tighten all eleven screws (7 inserted by the customer, 4 inserted at the factory) used to hold the Utility Cart together. STEP 9 (SEE FIGURE 6) Stand the Utility Cart on its front. Slide the Rear Axle through the mounting holes provided.
A-4 A-4 WELDER MOUNTING INSTRUCTIONS Small SP welder and Weldpak to the Utility Cart Parts Required: Part Number Description Required S19528 Mounting Clip 3 CF000014 1/4-20 x .75 screw 3 T9860-6 Lock Washer 3 CF000017 1/4-20 Hex Nut 3 Refer to FIGURE 8 while mounting your welder.
A-5 A-5 AC-225-C WELDER TO THE UTILITY CART Parts Required: Part Number Description Required S8025-54 1/4-20 x 1.25 4 Screw Refer to FIGURE 9 while mounting your AC-225-C welder. Position the AC-225-C as shown. Attach the AC-225- C with four 1/4 x 1 1/4 in.
A-6 A-6 OPERA TING INSTRUCTIONS The Utility Cart is designed for hand moving only. Do not attempt to pull the cart with any mechanized vehi- cle. Use the cart on a level surface only. Moving the cart over steep inclines could cause the cart to roll out of control, or tip over.
G2300 A.01 1 2 4 5 8 9 10 11 12 A A 12.85 34.58 A A A A 20.25 29.88 A A 33.88 A A 7 A A 14 31.03 A A INSIDE 6 N.A. N.A. N.A. .12 ± .12 4.00 ± .25 15 16 17 3 3 17.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECAUCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE PARA ESTE EQUIP AMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
An important point after buying a device Lincoln Electric IM468-A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lincoln Electric IM468-A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lincoln Electric IM468-A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lincoln Electric IM468-A you will learn all the available features of the product, as well as information on its operation. The information that you get Lincoln Electric IM468-A will certainly help you make a decision on the purchase.
If you already are a holder of Lincoln Electric IM468-A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lincoln Electric IM468-A.
However, one of the most important roles played by the user manual is to help in solving problems with Lincoln Electric IM468-A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lincoln Electric IM468-A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
