Instruction/ maintenance manual of the product 1999 Continental Lincoln Electric
Go to page of 208
Before driving Introduction 2 Instrumentation 3 Controls and features 20 Seating and safety restraints 87 Starting and driving Starting 110 Driving 115 Roadside emergencies 130 Servicing Maintenance and care 147 Capacities and specifications 191 Customer assistance 197 Reporting safety defects 209 Index 210 All rights reserved.
ICONS Indicates a safety alert. Read the following section on W arnings. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.
W ARNINGS W arnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment. BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently .
RESUME SET ACCEL COAST OFF ON 80 MPH km/h ABS P ! BRAKE + – RPMx1000 N O R M T/C OFF C H E F FILL ON RIGHT SERVICE ENGINE SOON AIR BAG TURN ON HEAD LAMPS 0 1 2 3 4 56 7 0 20 60 80 100 120 0 20 40 60 100 120 140 160 180 200 40 OFF HI LO P 0FF LIGHTS AUTO LAMP SRS Headlamp control (pg.
NEXT MODE VOL TEMP FAN 000000.0 SYSTEM DRIVER ID MENU TRIP RESET SELECT DISPLAY DTE ECON VEHICLE HANDLING N I T N O C L A T N E VOL PUSH ON TAPE MUTE SEEK TUNE AM FM REW FF SIDE 1 2 COMP SHUFF EXT OFF.
W ARNING LIGHTS AND CHIMES Service engine soon Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly installing and securely tightening the gas cap. After three driving cycles without these or any other temporary malfunctions present, the Service Engine Soon light should turn off.
Also illuminates when the parking brake is engaged. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately . Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned to the ON position and the engine is off.
Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly , requiring electrical system service. Engine oil pressure Momentarily illuminates when the ignition is turned to the ON position and the engine is off.
Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’ s door is opened. T urn signal chime Sounds when the turn signal lever has been activated to signal a turn and the vehicle is driven more than 0.
Speedometer Indicates the current vehicle speed. Odometer The odometer is located in the message center . It registers the total kilometers (miles) of the vehicle. Pressing the E/M control will alternate between English (miles) and Metric (kilometers) measurements.
Never remove the coolant reservoir cap while the engine is running or hot. This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. ELECTRONIC MESSAGE CENTER The electronic message center only works when the ignition is in the ON position.
If you have a vehicle with the Driver Select System, you have a DRIVER ID control in place of the E/M control. • Refer to DRIVER ID (if equipped) for DRIVER ID control information.
• distance to empty • traction control • ride control System warnings System warnings alert you to possible problems or malfunctions in your vehicle’ s operating systems. The message center will display the last selected feature if there are no more warning messages.
W arning messages that have been reset are divided into two categories: • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-ON cycle has been completed. This acts as a reminder that these warning conditions still exist within the vehicle.
E/M (if equipped) Press this control to switch the odometer and the message center display from metric (kilometers) to English (miles) units, and to change the temperature indication on the climate control unit. DRIVER ID (if equipped) Press this control to set vehicle comfort settings for up to two drivers.
Press the SELECT control to change these settings while in VEHICLE HANDLING mode. The combination of firm ride control (if equipped) and low steering effort is undesirable and cannot be selected. MENU Press this control to change various convenience settings throughout the vehicle.
under Operator Selectable Features. Refer to “Message Center” in this chapter for more information on the Message Center controls. The Message Center has a Driver ID control, which when pressed, allows the driver to select either Driver 1, Driver 2 or OFF .
Once the system has identified the driver (DRIVER MEMOR Y 1 or DRIVER MEMOR Y 2), the seat and mirror will automatically begin to move to that driver profile.
• The DRIVER ID control will display the option of selecting Driver 1, Driver 2 or OFF (Driver Select System only). Memory profile features Express window • Setting is saved as vehicle setting only .
• V ehicle with optional Driver Select System, setting may be saved to either the DRIVER MEMOR Y 1 or 2 personalized profiles or as a vehicle setting. • Settings-ON or OFF • Original setting-ON • Setting adjustment made using: Message Center -MENU/SELECT controls Reverse mirrors • Setting is saved as vehicle setting only .
Adjustable steering • Setting is saved as vehicle setting only . • V ehicle with optional Driver Select System, setting may be saved to either the DRIVER MEMOR Y 1 or 2 personalized profiles or as a vehicle setting.
• Settings-8–way adjustment • Original setting-N/A • Setting adjustment made using: driver seat control Outside mirror position • Setting may be saved to either the DRIVER MEMOR Y 1 or 2 personalized profiles or as a vehicle setting.
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps only . Rotate to the second position to also turn on the headlamps. The exterior lamps will illuminate when the ignition is ON and the windshield wiper control is in the interval, LO or HI position.
Flash to pass Pull toward you to activate and release to deactivate. P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation.
CLIMATE CONTROL SYSTEM Electronic Automatic T emperature Control (EA TC) system The EA TC system will maintain a selected temperature and automatically control airflow . Y ou can override automatic operation with any of the override controls, the fan speed control or the steering wheel controls (if equipped).
If unusual conditions exist (i.e.-window fogging, etc.), the manual override controls allow you to select airflow locations and the fan control allows you to adjust fan speed as necessary .
Fan speed ( ) When AUTO is pressed, fan speed is adjusted automatically for existing conditions. Y ou can override fan speed at any time. T o control fan speed manually , press the fan control or the steering wheel fan speed control to cancel automatic fan speed operation.
• MAX A/C-Uses recirculated air to cool the vehicle. The temperature will display 16°C (60°F). T o exit, press AUTOMA TIC or any other override controls. MAX A/C is noisier than normal A/C but more economical and will cool the inside of the vehicle faster .
Displaying outside temperature Press EXT to display the outside air temperature. It will be displayed until EXT is pressed again. If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window .
• If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle.
CLOCK Press + to increase the time displayed. Press – to decrease the time displayed. USING YOUR AUDIO SYSTEM Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated.
High Level Audio System with Premium AM/FM Stereo/Cassette (Radio Controlled CD Changer Compatible) Premium AM/FM Stereo/Cassette/Alpine Audio System (Radio Controlled CD Changer Compatible) VOL PUSH .
Y our vehicle is equipped with a delayed accessory feature. This feature enables the audio playing media to continue playing up to 10 minutes after the ignition has been turned off, or until a door is opened. V olume/power control Press the control to turn the audio system on or off.
• to increase volume compensation • to decrease or shut off the volume compensation AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). AM/FM select in radio mode This control allows you to select AM or FM frequency bands.
T une adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer . (Play will begin on the first track of the disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc.
Scan function The scan function works in radio, tape or CD mode (if equipped). Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode.
Autoset memory preset Autoset allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1.
Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. T ape/CD select (if equipped) • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the T APE control.
• In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in tape and CD modes (if equipped). • In the tape mode, tape direction will automatically reverse when the end of the tape is reached.
Press the COMP control to activate and deactivate compression adjust. Shuf fle feature The shuffle feature operates in CD mode and plays all tracks on the current disc in random order . If equipped with the CD changer , the shuffle feature continues to the next disc after all tracks are played.
• Use the SEL control to select the program type. W ith the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info .
Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Digital signal processing (if equipped) The digital signal processing (DSP) feature allows you to change the signal mode to suit your listening tastes.
CD changer (if equipped) Y our CD changer is either located in the passenger’ s footwell area or in the center console. Slide the door to access the CD changer magazine. Press to eject the magazine. Make sure only one disc is inserted in each slot. Each disc must be inserted with the label surface upward.
The magazine does not need to be full for the changer to operate. Radio power must be turned on to play the CDs in the changer . The magazine may be stored in the glove compartment when not being used. The CD magazine may be inserted or ejected with the radio power off.
CD and CD changer care • Handle discs by their edges only . Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extended periods of time. • Do not insert more than one disc into each slot of the CD changer magazine.
Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.
WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.
The flash rate of the turn signal will speed up considerably if the Lighting Control Module detects a left or right turn lamp bulb (front or rear) is burned out. STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features • Press BAND/MODE to select AM, FM1, FM2, T APE or CD (if equipped).
SPEED CONTROL T o turn speed control on • Press ON. V ehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). When the ON control is pressed, the message “SPEED CONTROL READY” will appear for 5 seconds in your message center .
T o set a speed • Press SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). When the SET ACCEL control is pressed, the message “SPEED CONTROL SET” will appear for 5 seconds in your message center .
• Accelerate with your accelerator pedal, then press and release SET ACC/SET ACCEL. When the SET ACCEL control is pressed and released, the message “SPEED CONTROL SET” will appear for 5 seconds in your message center . Y ou can accelerate with the accelerator pedal at any time during speed control usage.
• Press the OFF control. Pressing OFF will erase the previously programmed set speed. When the OFF control is pressed, the message “ SPEED CONTROL OFF” will appear for 5 seconds in your message center . T o return to a previously set speed • Press RES/RSM/RESUME.
Never adjust the steering wheel when the vehicle is moving. INTERIOR LAMPS Map lamps T o turn on the map lamps, press the control next to each lamp. If equipped with a moon roof, the map lamps are located on the rearview mirror . Press the control next to the map lamp to illuminate the lamp.
LINCOLN RESCU SYSTEM (IF EQUIPPED) Lincoln RESCU runs a self-test when you start your vehicle. During this test, the Lincoln RESCU warning light (located in the overhead console) will illuminate for several seconds.
Quick summary • T o utilize your vehicle’ s RESCU system, your cellular phone must be activated and plugged into the vehicle interface. • Information or emergency assistance can be requested whenever your key is in the RUN/ST ART position and for six minutes after the vehicle is turned off.
General description Lincoln’ s Remote Emergency Satellite Cellular Unit (RESCU) is designed to expedite roadside, emergency or information assistance to distressed motorists who are uncertain of their location and/or are uncertain of who to contact for assistance.
Information icon The Information icon is provided for customer information, such as points of interest near your current location, route assistance and other services as they become available. There may be charges incurred for certain services. Emergency (S.
Activation and deactivation When either of the two Lincoln RESCU controls are pressed, or the air bags are deployed (this will activate the system as an emergency automatically), a warning light, loca.
Message center interface During an activation, Lincoln RESCU communicates with the vehicle’ s message center . Status messages describing the sequence of the steps being executed are displayed, allowing you to visually follow the activation process.
Similarly , if the cellular call is disconnected by the network prior to receipt of the termination tone, another call to the response center will also automatically be dialed. The message “REDIAL IN PROGRESS” will be displayed on the message center and voice communication with an operator will be restored.
Lincoln RESCU system limitations • Inoperative if cellular phone inactive or inoperative Lincoln RESCU utilizes your vehicle’ s cellular phone and will not operate if cellular service has not been activated or if the phone is inoperative.
system will operate but the response center will not be able to identify your location. In this situation, the operator will depend on you to provide verbal information regarding vehicle location.
• Incompatible or performance limited with certain cellular providers features Some cellular carriers offer customers various optional features with their cellular services. Several of these features are not compatible or could potentially limit the performance of your Lincoln RESCU System.
1–800–334–1327. Alternatively , the registration process can be completed on-line during an acquaintance period activation. (See “Acquaintance activations” later in this section for details.) The information requested will aid in servicing you more efficiently during an assistance request.
Service charges For four years, beginning with your vehicle’ s warranty period, you will be entitled to unlimited emergency and roadside assistance activations without facing service charges. (These activations should be made only when emergency or roadside assistance is required.
ILLUMINATED VISOR MIRROR T o turn on the LH visor mirror lamps, lift the mirror cover . Adjust the amount of light by sliding the control. T o turn on the RH visor mirror lamps, lift the mirror cover .
Programming 1. Prepare for programming the HomeLink t Universal T ransceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds.
T o program your hand-held transmitters: • continue to hold the button on the HomeLink t Universal T ransceiver . • press and re-press the hand-held transmitter button every two seconds until the red light changes from a slow to a fast flash.
3. Press and release the programmed HomeLink t button. Press and release the HomeLink t button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training). The 2nd or 3rd press from step 3 will activate the door .
ELECTRONIC COMPASS (IF EQUIPPED) The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antennas. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy .
2. Locate the compass module mounted at the base of mirror . 3. T urn the ignition to the ON position. 4. Insert an appropriate diameter rod (paperclip) into the right switch access hole underneath the compass module and gently press for 1 to 2 seconds until ZONE and the current zone setting are displayed on the upper right corner of the mirror .
5. Release pressure from the switch. 6. Slowly drive the vehicle in a circle (less than 5 km/h [3 mph]) until the CAL indicator turns off. This will take up to five circles to complete calibration. 7. The compass is now calibrated. The compass display will remain on for approximately 40-45 minutes after the ignition key is removed.
POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors. Smart locks W ith the key in the ignition, in any switch position, and either the driver’ s or passenger’ s door open, the doors cannot be locked using the front door lock switches.
• Pull the top portion of the rocker switch to close. Express down T o make the driver window open fully without holding the window control, press the driver window control completely down. Press or pull the control to stop window operation. Window lock The window lock feature allows only the driver to operate the power windows.
POWER SIDE VIEW MIRRORS The ignition must be in ACC or ON position to adjust the power side view mirrors. T o adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror . 2. Move the control in the direction you wish to tilt the mirror .
CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door .
FUEL DOOR RELEASE Y our vehicle is equipped with a locking fuel door . T o open the door , press the control located on the door . Fuel filler door override release If the remote release is inoperative, open the trunk, then pull the override release handle located inside the trunk on the passenger side to open the fuel filler door .
Mini console (if equipped) The mini console is available in the six passenger vehicle only , and consists of the: • cupholder • compact disc changer (if equipped) • ashtray and lighter Use only soft cups in the cupholder . Hard objects can injure you in a collision.
The system is ready to arm whenever the ignition is turned OFF . Any of the following actions will prearm the alarm system: • Lock the doors with the remote transmitter (doors opened or closed). The horn will chirp to confirm that the control was pressed.
• Unlock the doors by using your keyless entry keypad. • Unlock the doors with a key . T urn the key full travel (toward the front of the vehicle) to make sure the alarm disarms. • T urn ignition to ACC or ON. REMOTE ENTRY SYSTEM The remote entry system allows you to lock or unlock all vehicle doors without a key .
This process will arm your anti-theft system (if equipped). For more information on arming the anti-theft system, refer to Perimeter anti-theft system in this chapter . Opening the trunk Press the control once to open the trunk. Ensure that the trunk is closed and latched before driving your vehicle.
Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. T ypical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Replacing lost transmitters T ake all your vehicle’ s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed), perform the followin.
Press the control once to unlock the driver’ s door and move the memory features to the corresponding memory position, just as if you had pressed the memory control in the vehicle. • transmitter #1 will recall memory profile position #1. • transmitter #2 will recall memory profile position #2.
Y our vehicle has a factory-set 5–digit code that operates the keyless entry system. Y ou can also program your own 5–digit personal entry code. The factory-set code is located: • on the owner.
Erasing personal code T o erase all of the personal entry codes programmed to a vehicle: 1. Enter the factory-set code. 2. Press 1/2 within 5 seconds of step 1. 3. Press and hold 1/2 for two seconds. All of the vehicle doors will lock and then unlock to confirm erasure.
Locking doors with the keyless entry system It is not necessary to enter the factory-set code prior to locking all doors. T o lock the doors: 1. Press 7/8 and 9/0 at the same time.
The SecuriLock y passive anti-theft system provides an advanced level of vehicle theft protection. Y our vehicle’ s engine can only be started with the two special SecuriLock y electronically coded keys provided with your vehicle. Each time you start your vehicle, the SecuriLock y key is read by the SecuriLock y passive anti-theft system.
Theft indicator The theft indicator on top of the dash will operate as follows: • When the ignition is OFF , the theft indicator will flash briefly every 2 seconds to indicate the SecuriLock y system is protecting your vehicle. • When the ignition is turned to RUN or ST ART , the theft indicator will light for 3 seconds and then go out.
3. W ithin five seconds of turning the ignition to OFF , insert the second previously programmed SecuriLock y key into the ignition and turn the ignition from OFF to RUN (maintain ignition in RUN for at least one second but no more than 5 seconds). 4.
SEA TING Adjustable head restraints Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Press the control to recline the seatback forward or backward.
Press to move the rear portion of the seat cushion up or down. Heated seats (if equipped) T o operate the heated seats: • Slide the control to BACK to heat the seatback only . • Slide the control to BOTH to heat the seatback and the seat cushion. • Rotate the thumbwheel to select the desired heat (from 0 (OFF) to 5 (HI)).
Easy access/easy out feature This feature automatically moves the driver’ s seat backward when: • the transmission is in N (Neutral) or P (Park) • the key is removed from the ignition cylinder T.
Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair . 1) Use the shoulder belt on the outside shoulder only . Never wear the shoulder belt under the arm.
Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • When a tight lap/shoulder fit is desired.
• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. T o tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips.
Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position.
AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
NHTSA recommends a minimum distance of at least 25 cm (ten [10] inches) between an occupant’ s chest and the air bag module. Steps you can take to properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably .
Air bags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.
While the system is designed to help reduce serious injuries, it may also cause minor burns, abrasions, swelling or temporary hearing loss. Because air bags must inflate rapidly and with considerable .
Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Air bag readiness section in the Instrumentation chapter . Routine maintenance of the air bag is not required.
How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment.
Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual.
SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children. Also see Air Bag Supplemental Restraint System (SRS) in this chapter for special instructions about using air bags.
Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle.
SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the safety seat you put in your vehicle.
Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Attaching safety seats with tether straps Some manufacturers make safety seats that include a tether strap that goes over the back of the vehicle seat and attaches to an anchoring point. Other manufacturers offer the tether strap as an accessory . Contact the manufacturer of your child safety seat for information about ordering a tether strap.
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
2. Make sure the headlamps and vehicle accessories are off. • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). 3. T urn the key to 4 (ON) without turning the key to 5 (ST ART).
Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light will not illuminate. ST ARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts.
Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly . Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below .
Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air . Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves and other debris.
BRAKES Y our service brakes are self-adjusting. Refer to the maintenance guide and or service guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system.
ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn off the ignition whenever you leave your vehicle. The parking brake is not recommended to stop a moving vehicle. However , if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency .
Wheel-speed sensors allow excess front wheel spin to be detected by the T raction Control y portion of the ABS computer . Any excessive wheel spin is controlled by automatically applying and releasing the front brakes in conjunction with engine torque reductions.
If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually , but it takes more effort. If the steering wanders or pulls, the condition could be cause.
The air suspension shut-off switch is located on the left side of the trunk. If this switch is in the OFF position, the rear air suspension will not operate. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle.
If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears in a steady pattern. Press lightly on the accelerator in each gear . Do not rock the vehicle for more than a few minutes, because it could damage the vehicle.
Understanding gearshift positions P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift is securely latched in P (Park). This locks the transaxle and prevent the front wheels from rotating. Always set the parking brake fully and make sure the gearshift is securely latched in P (Park).
N (Neutral) W ith the gearshift in the N (Neutral) position, the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Overdrive) The overdrive position is the normal driving position for an automatic overdrive transaxle.
When to use 3 (Third) 3 (Third) eliminates the needless shifting back and forth between third and fourth gears that your vehicle may do when driving on hilly terrain. It also gives more engine braking than overdrive to slow your vehicle on downgrades.
When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). T urn off the ignition whenever you leave your vehicle. Never leave your vehicle unattended while it is running.
• GA WR (Gross Axle W eight Rating) : Carrying capacity for each axle system. The GA WR is specific to each vehicle and is listed on the Safety Compliance Label on the driver’ s door pillar . • GCWR (Gross Combined W eight Rating) : Maximum combined weight of towing vehicle (including passengers and cargo) and the trailer .
Y ou may add equipment throughout your vehicle if the total weight added is equal to or less than the T otal Axle Reserve Capacity (T ARC) weight. Y ou should NEVER exceed the T otal Axle Reserve Capacity .
The amount of weight your loaded trailer should be no more than 907 kg (2 000 lbs.). Do not exceed the GVWR or the GA WR specified on the Safety Compliance Certification Label.
T railer lamps Do not connect a trailer’ s lighting system directly to your vehicle’ s lighting system. T o get the proper equipment for hooking up your trailer’ s lamps, see your Lincoln dealer . Be sure to follow their instructions carefully .
HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously .
FUSES AND RELA YS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating.
Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses.
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Description 1 5A Lighting Control Module: Anti-Theft Indicator Lamp, PWM Dimming Output, Illumination Lamps for Microphone, RR and L.
Fuse/Relay Location Fuse Amp Rating Description 12 10A Lighting Control Module 13 15A Lighting Control Module (LCM): RF T urn Lamp, Right T urn Indicator (VIC), RR Side Marker Lamps, T ail Lamps, Lice.
Fuse/Relay Location Fuse Amp Rating Description 31 15A Lighting Control Module (LCM): FCU, Electronic Day/Night Mirror , RH and LH Courtesy Lamp, Door Courtesy Lamps, RH and LH Map Lamps, RR and LR Reading Lamps, RH and LH V isor Lamps, Storage Bin Lamps, T runk Lid Lamp, Glove Box Lamp, Light Sensor Amplifier 32 15A Speed Control DEAC.
Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating D.
Fuse/Relay Location Fuse Amp Rating Description 1 30A* PCM 2 20A* AL T SENSE 3 30A* Right Rear Passenger W indow 4 30A* Air Suspension 5 — Not Used 6 20A* Horns 7 15A* High Beam 8 30A* Right Front P.
3. Remove the spare tire, jack and lug wrench. 4. Locate pry off notch (if equipped) and remove the center ornament from the aluminum wheel with the tapered end of the wheel nut wrench that came with your vehicle. Insert and twist the handle, then pry against the wheel.
On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to Air suspension system in the Driving chapter for more information. 6. Put the jack in the jack notch next to the door closest to the tire you are changing.
9. Remove the jack and fully tighten the lug nuts in the order shown. 10. Put flat tire, jack and lug wrench away . 11. If using a mini-spare tire, turn off the traction control switch.
JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. Y ou could damage the catalytic converter . Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted.
Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor .
Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for a further three minutes before disconnecting the jumper cables.
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
W RECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with slingbelt equipment.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service.
Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
1. Automatic transmission fluid dipstick 2. Brake fluid reservoir 3. Battery 4. Air filter assembly 5. Engine oil dipstick 6. Engine oil filler cap 7. Power steering fluid reservoir 8. W indshield washer fluid reservoir 9. Engine coolant reservoir 10.
6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range.
Engine oil and filter recommendations Look for this certification mark. Ford oil specification is WSS-M2C153-G. Use SAE 5W -30 motor oil certified for gasoline engines by the American Petroleum Institute. Do not use supplemental engine oil additives, oil treatments or engine treatments.
BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules: 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir .
WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way .
If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become empty . If this occurs, a LOW ENGINE COOLANT warning will illuminate in the message center and you will need to add engine coolant to the coolant reservoir .
3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. Change your engine coolant according to the appropriate schedule listed in the Scheduled Maintenance Guide.
Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter . Have your dealer check the engine cooling system for leaks if you have to add more than 1.
4. Check the fluid level in the reservoir . It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low , add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines.
7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal and room temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the outside temperatures are above 10°C (50°F).
An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.
Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation.
If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal.
2. Release and open the hood. 3. Pull the rubber cowl seal (number 1 in figure) away from the cowl vent screen. Remove the right half of the cowl vent screen (number 2 in figure) by placing your hand underneath the cowl vent screen and lifting straight up to release the four spring clips.
Be careful when installing the new filter . A void bending or tearing the filter and make sure it is fully seated in its mounting location after installation. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective.
At zero pressure, the SecuriT ires will provide you with a minimum driving capability of approximately 30 km (20 miles). How you drive and the actual amount of air pressure left in your tires will determine exactly how many miles can be driven.
Flat tire warning If the sensors detect a tire pressure lower than 68 kPa (10 psi), the LOW TIRE PRESSURE warning will appear in the overhead console and the message W ARNING LOW TIRE PRESSURE will be displayed in the message center , indicating an impending flat tire.
T ire Quality Grades apply to new pneumatic tires for use on passenger cars. They do not apply to deep tread, winter -type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in T itle 49 Code of Federal Regulations Part 575.
T emperature A B C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
• Four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over .
SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. Snow tires must be the same size and grade as the tires you currently have on your vehicle.
Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed.
Fuel Filler Cap Y our fuel tank filler cap has an indexed design with a one-eighth turn on/off feature. When fueling your vehicle: 1. T urn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe.
V ehicles certified to meet California emission standards (indicated on the underhood V ehicle Emissions Control Information label) are designed to operate on California cleaner -burning, low-sulfur gasolines.
Cleaner air Ford approves the use of gasolines to improve air quality , including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE. Running out of fuel A void running out fuel because this situation may have an adverse affect on modern powertrain components.
The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill Capacities chart in this “Owner Guide.” The advertised capacity is the amount of the Indicated Capacity and the Empty Reserve combined.
Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’ s fuel economy . Additionally , keeping records during summer and winter will show how temperature impacts fuel economy .
• Operating a vehicle with the wheels out of alignment will reduce fuel economy . • Use recommended engine oil. Refer to Lubricant Specifications . • Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in your vehicle Scheduled Maintenance Guide.
EMISSION CONTROL SYSTEM Y our vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. T o make sure that the catalytic converter and other emission control components continue to work properly: • Use only unleaded fuel.
Do not make any unauthorized changes to your vehicle or engine. By law , vehicle owners and anyone who manufactures, repairs, items, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
• Backup lamps • License plate lamp Do not remove lamp bulbs unless they will be replaced immediately . If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’ s reach.
5. Release clip and disconnect the electrical connector from the bulb. 6. Remove the bulb retaining ring by rotating it counterclockwise. 7. Remove the old bulb from the lamp assembly by pulling it straight out of the lamp assembly . T o install the new bulb: 1.
5. Carefully position the headlamp assembly onto the vehicle making sure the alignment pins are inserted into the proper holes. 6. Hold the headlamp assembly snugly against the vehicle and push down on the retainer pins to lock the lamp into place. 7.
High-mount brakelamp bulbs For bulb replacement, see a dealer or qualified technician. Replacing tail lamp/backup bulbs For bulb replacement, see a dealer or qualified technician. Replacing license plate lamp bulbs For bulb replacement, see a dealer or qualified technician.
Function T rade Number Illuminated visor mirror 74 Overhead console reading lamp (without moon roof) 912 Passenger assist handle (rear seat) 211-2 T o replace all instrument panel lights - see your dealer . AIMING THE HEADLAMPS Y our vehicle is equipped with a V ehicle Headlamp Aim Device (VHAD) on each headlamp.
3 .U s ea4m m wrench or socket to turn the horizontal adjusting screw until the “0” mark on the yellow dial lines up with the reference mark on the marker (as shown) when viewed directly from above. T urning the horizontal adjusting screw in the direction of the arrow changes the horizontal aim as shown.
3. The “U” and “D” on the bubble indicate the directional change (up or down) of the vertical aim. 4 .U s ea4m m wrench or socket to turn the vertical adjusting screw until the bubble is centered between the two red lines which represents the “0” mark position.
W axing your vehicle W ax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use cleaning fluid or alcohol with a clean cloth to remove any bugs and tar before waxing vehicle.
• Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning.
treatments used by commercial car washes. Clean the outside of the windshield with a non-abrasive cleanser such as the non-abrasive Bon-Ami t powder . Rinse thoroughly with clean water . Do not use abrasive cleansers on glass as they may cause scratches.
Cleaning leather seats (if equipped) T o clean, simply use a soft cloth dampened with water and a mild soap. W ipe the leather again with a damp cloth to remove soap residue. Dry with a soft cloth. For tougher soiling concerns, Ford recommends using the leather cleaning kit F8AJ-19G253–AA, which is available from your Ford Dealer .
MOTORCRAFT PART NUMBERS Component 4.6L DOHC V8 engine Air filter F A-1615 Cabin air filter FP-5 Fuel filter FG-800A Battery BXT -65-750 Oil filter FL-820-S PCV valve EV -111 Spark plugs* A WSF-32E * Refer to V ehicle Emissions Control Information (VECI) decal for spark plug gap information.
2 Use only brake fluids certified to meet Ford specifications. Refer to Adding engine coolant, in the Maintenance and Care chapter . DOT 3 fluid is recommended.
Item Ford Part Name or equivalent Ford Part Number Ford Specification Power steering fluid Motorcraft MERCON t AT F XT -2-QDX MERCON t W indshield washer fluid Ultra-Clear W indshield W asher Concentrate C9AZ-19550-AC ESR-M17P5-A 1 Use only brake fluids certified to meet Ford specifications.
1 4 5 3 2 Capacities and specifications 198.
IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
V ehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. For your protection, you will also find the vehicle iden.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
Accessory delay .......................... 75 Air bag supplemental restraint system ........................................ 101 and child safety seats ............ 102 description ....................... 101,105 disposal .............................
Fuses ................................... 136,137 Gas mileage (see Fuel economy) ..............178,179,180,181 Gauges ......................................... 10 engine coolant temperature gauge ......................................... 11 Hazard flashers .
replacement/additional transmitters ............................... 84 replacing the batteries ............. 83 Safety belts (see Safety restraints) ................. 9 Safety restraints cleaning the safety belts .................................. 100,193 extension assembly .
205.
206.
207.
Item Information Recommended fuel Unleaded fuel only - 91 octane Fuel tank capacity 75.7L (20.0 gallons) Engine oil capacity (includes filter change) 5.7L (6.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. Automatic transaxle fluid capacity 1 13.
An important point after buying a device Lincoln Electric 1999 Continental (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lincoln Electric 1999 Continental yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lincoln Electric 1999 Continental - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lincoln Electric 1999 Continental you will learn all the available features of the product, as well as information on its operation. The information that you get Lincoln Electric 1999 Continental will certainly help you make a decision on the purchase.
If you already are a holder of Lincoln Electric 1999 Continental, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lincoln Electric 1999 Continental.
However, one of the most important roles played by the user manual is to help in solving problems with Lincoln Electric 1999 Continental. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lincoln Electric 1999 Continental along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
