Instruction/ maintenance manual of the product HC 1011/1060 Liebherr
Go to page of 14
Installation Instructions Combined fridge-freezer for integrated use, door-on-door HC 1011/1060 HC 1001/1050 020707 7084000 - 01.
Contents 1 General safety information ........................... 2 2 Setting up the appliance ............................... 2 3 Changing the door hinges ............................ 3 3.1 To detach the soft stop mechanism.................. 3 3.2 Reversing the door .
u Examine the unit and packaging for shipping damage. Contact the carrier immediately if you suspect there is any damage. u Note the type (model, number), index, appliance/serial number, date of purchase and where purchased on the spaces provided in see Appliance Information.
u Screw in ball stud Fig. 3 ( 3) together with the soft stop mechanism Fig. 3 ( 2) in the fastening hole. u Re-attach all covers Fig. 2 ( 5,6,7,8) . 4 Kitchen Cabinet Construction This is a fully integrated appliance which means that it is fully enclosed by a kitchen cabinet.
Fig. 6 u In the cabinet base, cut out a ventilation opening that is 17-23/32 in. ( 450 mm) in width and 2-7/32 in. (56 mm ) in height. u Insert ventilation grille Fig. 6 ( 3) into the cabinet base cut- out Fig. 6 ( 1) . u From the back side, slide the snap-fits Fig.
w The floor and side walls must be at right angles to each other. The joint between the upper and the lower kitchen cabinet door must align with the joint between the upper and lower appliance door. Follow distance L to the wall to allow the drawers to be pulled out properly.
Fig. 7 1 Unit door fridge compartement 3 Fridge compartement door 2 Unit door freezer compartement 4 Freezer compartement door The freezer door height is 24-24/32 in. (629 mm). u To cover the lower part of the appliance: increase the height of the panel to 27-3/32 in.
u The total opening of the cabinet (i.e. 70-3/8 in. (1788 mm)) plus the thickness of the top as well as the floor board (usually 3/4 in. (19 mm )) minus the height of the freezer door panel (xxx in. (xxx mm)) as calculated above and subtract the width of the gap (approximately 1/8 in.
Note u Before assembling the unit door, make sure that the permitted weight for the unit doors is not exceeded. u Otherwise damage to the hinges and malfunctions arising from this cannot be ruled out. Maximum weight of unit door Fridge compartment door 30.
For appliances with a fixed water supply for the IceMaker: * u Connect the IceMaker as indicated the section entitled Water Supply.* u Fit the locking clip Fig. 11 ( 62) .* Fig. 11 * All appliances: u Push the appliance 3/4 of the way into the recess.
u Slightly loosen the screws Fig. 20 ( 55) . u Secure the top mounting bracket Fig. 20 ( 50) to the unit wall with a ø4x19 chipboard screw Fig. 20 ( 29) . u Break off the protruding end of the cover Fig. 20 ( 53) . Fig. 20 u Tighten the screws Fig. 20 ( 55) .
Ensure that both metal edges are flush, symbol // : u Drill pilot holes in the door of the unit (you could make a preliminary hole with a bradawl). Fig. 25 u Fasten the appliance door to the unit door with screws Fig. 25 ( 41) through the mounting brackets Fig.
7 Connecting the appliance WARNING Electrical shock hazard! u Start-up should only take place once the appliance has been installed according to these instructions. u Electrically ground appliance. u Do not ground to a gas pipe. u Check with a qualified electrician if you are not sure the appliance is properly grounded.
Connecting the appliance 14.
An important point after buying a device Liebherr HC 1011/1060 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Liebherr HC 1011/1060 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Liebherr HC 1011/1060 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Liebherr HC 1011/1060 you will learn all the available features of the product, as well as information on its operation. The information that you get Liebherr HC 1011/1060 will certainly help you make a decision on the purchase.
If you already are a holder of Liebherr HC 1011/1060, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Liebherr HC 1011/1060.
However, one of the most important roles played by the user manual is to help in solving problems with Liebherr HC 1011/1060. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Liebherr HC 1011/1060 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
