Instruction/ maintenance manual of the product WM2032HW LG Electronics
Go to page of 48
100 W ASHING MACHINE SER VICE MANUAL READ THIS MANUAL CAREFULL Y TO DIAGNOSE PROBLEMS CORRECTL Y BEFORE SERVICING THE UNIT . MODEL : WM241 1HW / WM201 1 HS WM201 1HW / WM181 1CW WM2432HW / WM2032 HS WM2032HW / WM1832CW CAUTION Website:http://www .LGEservice.
CONTENTS 1. SPECIFICA TIONS .........................................................................................................................3 2. FEA TURES & TECHNICAL EXPLANA TION ..........................................................
3 1. SPECIFICA TIONS ITEM WM241 1HW WM201 1HS / WM201 1HW WM181 1CW WM2432HW WM2032HS / WM2032HW WM1832CW POWER SUPPL Y 120V ~ 60Hz PRODUCT WEIGHT 190 lbs.
4 2. FEA TURES & TECHNICAL EXPLANA TION 2-1.FEA TURES Direct Drive System The advanced Brushless DC motor directly drives the drum without belt and pulley . Tilted Drum and Extra Lar ge Door Opening The tilted drum and extra large door opening make it possible to load and unload easily .
5 2-2.FUZZY LOGIC W ASHING TIME OPTIMIZA TION T o get the best washing performance, optimal time is determined by the water temperature, the selected washing temperature, and the size of the load. 2-3.W A TER LEVEL CONTROL This model incorporates a pressure sensor which can sense the water level in the tub.
6 3. P AR TS IDENTIFICA TION ACCESSORIES • If the supply cord is damaged, it must be replaced by the manufacturer or its authorized service technician in order to avoid a hazard.
7 Before servicing, ask the customer what the trouble is. Check the setup (power supply is 120V AC, remove the transit bolts....). Check with the troubleshooting guide. Plan your service method by referring to the disassembly instructions. Service the unit.
8 HOW TO CONNECT THE INLET HOSE V erify that the rubber washer is inside of the valve connector . Connect the inlet hose firmly to prevent leaks. CONNECT THE DRAIN HOSE CONNECT POWER PLUG The end of the drain hose should be placed less than 96 ” from the floor .
9 TEST OPERA TION Connect the power plug to the outlet. Connect the inlet hose. Press the POWER button twice to restart. Press the SPIN SPEED button. Press the ST ART / P AUSE button. Check the drain and spin functions. Listen for clicking sounds to determine if the door is unlocking.
10 5. OPERA TION • Use this button to turn the power On / Off . • Rotate the Cycle selector knob to select the cycle designed for different types of fabric and soil levels. • Allows you to store a customized wash cycle for future use. • T o create a Custom Program : 1) Select a cycle.
11 • Use this option to prevent unwanted use of the washer . Press and hold Quick Cycle and Delay W ash button for 3 seconds to lock / unlock control. • When Child lock is set, “ ” blinks and all buttons are disabled but the Power button. Y ou can thereby lock the washer while it is operating.
12 WM241 1HW WM201 1HS / WM201 1HW WM181 1CW WM2432HW WM2032HS / WM2032HW WM1832CW.
13 6. WIRING DIAGRAM / PROGRAM CHART WM241 1HW / WM201 1HS / WM201 1HW / WM2432HW / WM2032HS / WM2032HW WM181 1CW / WM1832CW.
14.
15 7. TROUBLESHOOTING 7-1. BEFORE PERFORMING SER VICE Be careful of electric shock when disconnecting parts for while troubleshooting. The voltage of each terminal is 120V AC and DC when the unit is plugged in. 7-2. QC TEST MODE. The washer must be empty and the controls must be in the off state.
16 7-4. ERROR DISPLA Y If you press the ST ART/P AUSE button when an error is displayed, any error except will disappear and the machine will go into the pause status. In case of if the error is not resolved within 20 sec., or the in case of other errors, if the error is not resolved within 4 min.
17 ERROR SYMPTOM CAUSE OVER CURRENT ERROR • MAIN PWB ASSEMBL Y is out of order . • Winding in the ST A TOR ASSEMBL Y is short-circuited. • The connector (3-pin, male, white) in the MOT OR HARNESS is not connected to the connector (3-pin, female, white) of ST A TOR ASSEMBL Y .
18 8-1.DIAGNOSIS AND SOLUTION FOR ABNORMAL OPERA TION 8. ERROR DIAGNOSIS AND CHECK LIST SYMPTOM GUIDE FOR SERVICE CALL No power W ater inlet trouble Is the power plug connected firmly to 120V AC outlet? Power failure? or Breaker opened? Is the outlet controlled by a switch? Visit to service.
19 SYMPTOM GUIDE FOR SERVICE CALL Door error Drain trouble W as the load too large? Visit to service. Visit to service..
20 SYMPTOM GUIDE FOR SERVICE CALL Suds overflow from the appliance. (In this condition, wash and spin do not operate normally) No softening effect Is a low-sudsing detergent used? Is the proper amount of detergent used as recommended? Recommend to reduce the amount of detergent.
Is the supplied voltage 120V AC? Is the voltage between the 2 FIL TER ASSEMBL Y connectors 120V AC? Is the LED(1) on? Are the connectors(2) on the PWB loose? Is wire of the DISPLA Y PWB ASSEMBL Y broken? Replace DISPLA Y PWB ASSEMBL Y or repair wire. Check the fuse or reset the circuit breaker .
NO YES NO NO YES NO YES YES NO NO YES YES YES NO NO NO YES 22 Is water supply shut-off? Is the tap opened? When you press both SPIN SPEED button and SOIL LEVEL button simultaneously , is the water level frequency below 246? Is the inlet valve filter clogged? Is resistance between each terminal of INLET V AL VE ASSEMBL Y 0.
23 ABNORMAL SOUND SOFTENER / BLEACH DOES NOT FLOW IN Secure the bolt. Replace the ST A TOR ASSEMBL Y or ROTOR ASSEMBL Y . Refer to NO W A TER SUPPL Y Check the wiring on the dispenser .
24 Replace the SENSOR SWITCH ASSEMBL Y . Replace the MAIN PWB ASSEMBL Y . Repair the DRAIN HOSE ASSEMBL Y . Remove foreign material. Reconnect or repair the connector Replace the DRAIN PUMP ASSEMBL Y .
25 Push the THERMISTOR tightly to the rubber . When checking the THERMISTOR on the tub, is the THERMISTOR loose? HEA TING CONTINUOUSL Y ABOVE THE SETTING W A TER TEMPERA TURE W ASH HEA TER TROUBLE.
WILL NOT CIRCULA TE W A TER Is the impeller of the drain pump clogged? Are the Hose Connector and/or Hose clogged? Is the connector disconnected, disassembled? Is the coil of the right side of drain p.
27 SPIN TROUBLE Check the SENSOR SWITCH ASSEMBL Y or HOSE (Pressure). If the problem is on the SENSOR SWITCH ASSEMBL Y or the HOSE, replace the SENSOR SWITCH ASSEMBL Y or the HOSE. Normal Correct the connection. Replace the ST A TOR ASSEMBL Y Check during spin if the frequency of the water level is 248 or more.
28 1. Unscrew 7 screws on the Rear Frame. 2. Disassemble the Rear Frame. 3. Pull the Control panel forward. 4. Disconnect connectors. 5. Unscrew 5 screws. 6. Disassemble the controller assembly . 1. Open the Lid. 2. Unscrew 4 screws. 3. Disassemble the Lid Assembly .
29 1. Disassemble the 5 hose clamps. 2. Release the 5 hoses. 3. Unscrew the nut at the lower part of the dispenser . 4. Unscrew the 4 screws on the holder . 5. Disassemble the 5 connectors from the valves. 1. Unscrew the screw from the top plate. 2. Unplug the 2 connectors.
30 1. Unscrew the 2 screws from upper side of the cabinet cover . 2. Unscrew the screw from filter cover . 3. Put a flat ( – ) screwdriver into the both sides of the filter cover , and pull it out. 4. Unscrew the 2 screws from the lower side of the cabinet cover .
31 Clamp Assembly 5. Open the door . 6. Disassemble the clamp assembly using a flat ( – ) screwdriver . 7. Separate the clamp assembly from cabinet cover . 8. T ilt the cabinet cover . 9. Disconnect the door switch connector . 10. Lift and separate the cabinet cover .
32 1. Open the door . 2. Unscrew the 7 screws from the hinge cover . 3. Put a flat ( – ) screwdriver into the opening of the hinge, and pull out the hinge cover . 4. Unscrew the screws from the door . 5. Disassemble the door upward / downward. 1. Open the door .
33 1. Disassemble the cabinet cover . 2. Separate the pump hose, the bellows and the circulation hose assembly from the pump assembly . 3. Disassemble the pump assembly in arrow direction. 1. Disassemble the cabinet cover . 2. Separate 2 connectors from the heater .
34 1. Disassemble the cabinet cover . 2. Separate the heater from the tub. 3. Remove any foreign objects (wire, coin, etc.) by inserting a long bar in the opening. 1. Unscrew the 4 screws from the back cover . 2. Unscrew the single screw from the lower-right side of the cabinet.
35 1. Disassemble the back cover . 2. Loosen the bolt. 3. Pull out the Rotor . 4. Unscrew the 2 screws from the tub bracket. 5. Loosen the 6 bolts on the stator . 6. Unplug the 2 connectors from the stator . 1. Disassemble the damper hinges from the tub and base.
36 10-1. CABINET & CONTROL P ANEL ASSEMBL Y 10. EXPLODED VIEW A160 A125 A105 F215 A495 A490 A303.
37 K344 K345 K123 K1 15 K 111 K340 F315 F463 K125 K343 K121 K101 K122 F141 K105 F463 F464 10-2. DRUM & TUB ASSEMBL Y.
38 F300 F160 F170 F120 A275 HOT (BLUE) A276 COLD (RED) F430 F435 F431 F440 F436 F432 F302 F301 10-3. DISPENSER ASSEMBL Y.
REPLACEMENT PARTS LIST CAUTION : Before replacing any part of these components Read carefully the safety precautions in this manual ■ NOTE : S(Safety Parts), AL(Alternative parts) LG MODEL: WD-10210BD ABWEEUS Run_Date : 2003-04-03 YOUR MODEL: WD-2032HW SPECIFICATION: 120V 60Hz S AL LOC DESCRIPTION PARTS No.
LG MODEL: WD-10210BD ABWEEUS Run_Date : 2003-04-03 YOUR MODEL: WD-2032HW SPECIFICATION: 120V 60Hz S AL LOC DESCRIPTION PARTS No. Q'TY REMARKS K121 BEARING,BALL 4280FR4048D 1 K122 BEARING,BALL 428.
REPLACEMENT PARTS LIST CAUTION : Before replacing any part of these components Read carefully the safety precautions in this manual ■ NOTE : S(Safety Parts), AL(Alternative parts) LG MODEL: WD-10215BD ATTEEUS Run_Date : 2003-04-03 YOUR MODEL: WD-2032HS SPECIFICATION: 120V 60Hz S AL LOC DESCRIPTION PARTS No.
LG MODEL: WD-10215BD ATTEEUS Run_Date : 2003-04-03 YOUR MODEL: WD-2032HS SPECIFICATION: 120V 60Hz S AL LOC DESCRIPTION PARTS No. Q'TY REMARKS K121 BEARING,BALL 4280FR4048D 1 K122 BEARING,BALL 428.
REPLACEMENT PARTS LIST CAUTION : Before replacing any part of these components Read carefully the safety precautions in this manual ■ NOTE : S(Safety Parts), AL(Alternative parts) LG MODEL: WD-12210BD ABWEEUS Run_Date : 2003-04-03 YOUR MODEL: WD-2432HW SPECIFICATION: 120V 60Hz S AL LOC DESCRIPTION PARTS No.
LG MODEL: WD-12210BD ABWEEUS Run_Date : 2003-04-03 YOUR MODEL: WD-2432HW SPECIFICATION: 120V 60Hz S AL LOC DESCRIPTION PARTS No. Q'TY REMARKS K115 SPIDER 4434ER0001A 1 K121 BEARING,BALL 4280FR404.
REPLACEMENT PARTS LIST CAUTION : Before replacing any part of these components Read carefully the safety precautions in this manual ■ NOTE : S(Safety Parts), AL(Alternative parts) LG MODEL: WD-90210BD ABWEEUS Run_Date : 2003-04-03 YOUR MODEL: WD-1832CW SPECIFICATION: 120V 60Hz S AL LOC DESCRIPTION PARTS No.
LG MODEL: WD-90210BD ABWEEUS Run_Date : 2003-04-03 YOUR MODEL: WD-1832CW SPECIFICATION: 120V 60Hz S AL LOC DESCRIPTION PARTS No. Q'TY REMARKS K121 BEARING,BALL 4280FR4048D 1 K122 BEARING,BALL 428.
.
101 DEC. 2002 PRINTED IN KOREA P/No.:3828ER3013T.
An important point after buying a device LG Electronics WM2032HW (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought LG Electronics WM2032HW yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data LG Electronics WM2032HW - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, LG Electronics WM2032HW you will learn all the available features of the product, as well as information on its operation. The information that you get LG Electronics WM2032HW will certainly help you make a decision on the purchase.
If you already are a holder of LG Electronics WM2032HW, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime LG Electronics WM2032HW.
However, one of the most important roles played by the user manual is to help in solving problems with LG Electronics WM2032HW. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device LG Electronics WM2032HW along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
