Instruction/ maintenance manual of the product STB1000 LG Electronics
Go to page of 86
© Copyright 201 1, LG Electronics U.S.A., Inc. P/N: 206-4147 (Rev A) STB1000 HD Commercial Interface Set-top Box for use in Lodging Environments Installation & Setup Guide W arranty.
2 206-4147 W ARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE P AR TS INSIDE. REFER T O QUALIFIED SERVICE PERSONNEL.
3 206-4147 IMPORT ANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation openings.
4 206-4147 IMPORT ANT SAFETY INSTRUCTIONS (Continued from previous page) 20. Grounding Ensure that you connect the earth ground wire to prevent possible electric shock (i.e., an STB with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet).
5 206-4147 Safety W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . 3 – 4 T able of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setup Checklist .
6 206-4147 Setup Checklist Installation and Setup __ Unpack the STB1000 and all accessories. Accessories provided: • 6 ft AC power cord • 5 ft RS-232C-F to RS-232C-F null-modem cable with 3.
7 206-4147 DIGIT AL VIDEO OUT AC IN AC OUT MAX 8A 960W USB SERVICE ONL Y A V IN 2 VIDEO L/MONO -AUDIO- R AUDIO OUT INT PILLOW PILLOW SPEAKER ANT DISPLA Y IR IN IR RECEIVER IN AC 120V~ 60Hz COMPONENT IN VIDEO AUDIO R L UPDATE RESET AUDIO (RGB/DVI) P B Y P R .
8 206-4147 COMPONENT IN VIDEO AUDIO R L UPDA TE RESET AUDIO (RGB/DVI) P B Y P R ..... .... .......... 2 1(DVI) DIGIT AL VIDEO IN OPTICAL DIGIT AL AUDIO OUT REMOTE CONTROL OUT SPEAKER OUT 8 RJP INTERF ACE RGB IN VIDEO R -A UDIO- L/MONO A V IN 1 RGB(PC) .
9 206-4147 POWER STATUS STB1000 DIGITAL VIDEO OUT AC IN AC OUT MAX 8A 960W USB SERVICE ONLY AV IN 2 VIDEO L/MONO -AUDIO- R AUDIO OUT INT PILLOW PILLOW SPEAKER ANT DISPLAY IR IN IR RECEIVER IN AC 120V~.
10 206-4147 STB1000 Cabling Connections Refer to the cabling diagram below , and complete the procedure on page 1 1 to connect the STB1000 to a compatible LG display panel.
11 206-4147 STB1000 Cabling Connections (Cont.) 1. Use one of the supplied RS-232 cables—either the serial DB9-Female to DB9-Female null-modem cable or the DB9-Female to DB9-Male straight-through ca.
12 206-4147 STB1000 Installer Remote The LG Installer Remote is supplied with and dedicated to operate the STB1000. See next page for typical key functions.
13 206-4147 Installer Remote Control T ypical Key Functions 1 2 3 4 5 6 7 8 9 0 ABC DEF GHI JKL MNO PQRS TUV WXYZ PIP CH- PIP CH+ PIP SW AP PIP INPUT PIP SAP FLASHBK REMOVE ALPHA/NUM P A G E MUTE TIMER MENU RETURN VOL CH POWER GUIDE INPUT CC ENTER TV DVD VCR STB &@ .
14 206-4147 Important: Pro:Centric operation requires that Installer Menu item 1 19 DA T A CHANNEL be set appropriately and that the STB1000 be in PPV or FTG Mode. The interactive Pro:Centric STB enables guests—from the comfort of their rooms—to view and select from a complete listing of hotel/institution services and amenities.
15 206-4147 STB1000 Setup Menus CHANNEL PICTURE AUDIO INPUT OPTION L OCK TIME USB PICTURE Enter Move TIME Enter Move AUDIO Enter Move CHANNEL Enter Move INPUT Enter Move LOCK Enter Move OPTION Enter Move On-screen setup menus control the basic features of the STB1000/display .
16 206-4147 Channel Setup Options Auto T uning (Channel Search) Auto T uning (Channel Search) Auto T uning automatically finds and stores all digital and analog channels available through antenna or cable inputs. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the CHANNEL menu option.
17 206-4147 Channel Setup Options (Cont.) Manual T uning (Add/Delete Channels) / View Digital Signal Strength Manual T uning (Add/Delete Channels) Use this option to manually add active channels or remove unwanted channels. See also “Edit Channels” on the following page.
18 206-4147 Channel Setup Options (Cont.) Edit Channels / Channel Labels CHANNEL Enter Move Close Channel ANALOG 1 1-0 Logo PBS ► ► PBS Edit Channels Use this option to add or delete channels from the channel lineup. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the CHANNEL menu option.
19 206-4147 Picture Setup Options Aspect Ratio (Picture Size) Control PICTURE Enter Move RG ► Aspect Ratio : 16:9 Picture Mode : Standard • Backlight 90 • Contrast 90 • Brightness 50 • Sharpness 50 • Color 50 • T int 0 16:9 Just Scan Set By Program 4:3 Zoom Notes: • The RGB-PC input source can only use the 4:3 or 16:9 aspect ratio.
20 206-4147 Picture Setup Options (Cont.) Picture Mode PICTURE Enter Move RG ► Aspect Ratio : 16:9 Picture Mode : Standard • Backlight 90 • Contrast 90 • Brightness 50 • Sharpness 50 • Col.
21 206-4147 Picture Setup Options (Cont.) Advanced Control Advanced Control 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the PICTURE menu option. Then, press ENTER . 2. Use the Up/Down arrows to select Advanced Control under Picture Mode, and then press ENTER .
22 206-4147 Picture Reset This option restores the Picture Mode to factory default settings. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the PICTURE menu option. Then, press ENTER . 2. Use the Up/Down arrows to select Picture Reset under Picture Mode, and then press ENTER .
23 206-4147 Screen Auto Con fi guration This option automatically adjusts the picture position and mini- mizes image instability . 1. In the Screen Menu, use the Up/Down arrows to select Auto Con fi g , and then press ENTER . 2. Use the Left/Right arrows to select Ye s , and then press ENTER to initiate the auto adjustment.
24 206-4147 Option Settings Menu Language / Audio Language Menu Language Use this option to select the language of on-screen menus. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the OPTION menu option. Then, press ENTER .
25 206-4147 OPTION Enter Move Menu Language : English Audio Language : English Caption : Off Set ID : 1 Demo Mode : Off Data Broadcasting Option Settings (Cont.) Captions Captions Use this option to select the appropriate mode for displaying captions.
26 206-4147 Option Settings (Cont.) Set ID / Demo Mode Set ID 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the OPTION menu option. Then, press ENTER . 2. Use the Up/Down arrows to select Set ID , and then press ENTER .
27 206-4147 Audio Setup Options Auto V olume / Clear V oice II / Balance Auto V olume Each broadcasting station has its own signal conditions, which may result in different volume levels for dif ferent programs/ channels. This option enables the STB1000 to make automatic adjustments to maintain a consistent volume level between channels.
28 206-4147 Audio Setup Options (Cont.) Sound Mode Sound Mode This feature enables you to select a preset Sound Mode option and/or customize sound settings manually . 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the AUDIO menu option.
29 206-4147 Audio Setup Options (Cont.) Audio Reset / TV Speaker / Secondary Audio Program (SAP) Setup Audio Reset This option restores the Sound Mode to factory default settings. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the AUDIO menu option.
30 206-4147 T ime Setup Options Set the STB Clock / STB On and Off Time Settings Set the STB Clock The STB1000 clock is set automatically from a digital channel signal. The signal includes clock information provided by the broadcasting station. Y ou can also set the clock manually if the auto clock function does not set the current time correctly .
31 206-4147 Sleep Timer 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the TIME menu option. Then, press ENTER 2.
32 206-4147 Lock Setup Options Lock System Overview / Enable or Disable the Lock System Lock System Overview Parental Control can be used to block individual channels, programs with speci fi c ratings or in speci fi c categories, and external viewing sources.
33 206-4147 Lock Setup Options (Cont.) Set Password / Channel Blocking LOCK Enter Move Lock System : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Set Password Use the following procedure to set a new password for the Lock System.
34 206-4147 Lock Setup Options (Cont.) Movie Rating / TV Rating-Children Movie Rating (MP AA) (for USA) This option blocks movies according to movie ratings limits. Y ou can set the ratings limit by blocking out all movies with ratings above a speci fi ed level.
35 206-4147 TV Rating-General (for USA) This option blocks TV programs based on US ratings. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the LOCK menu option. Then, press ENTER . 2. If prompted for it, enter the Lock System password.
36 206-4147 LOCK Enter Move Lock System : Off Set Password Block Channel TV Rating-English TV Rating-French Downloadable Rating Input Block E C C8+ G PG 14+ 18+ Blocking Off Blocking off : Permits all.
37 206-4147 Downloadable Rating This option is available only for digital channels and operates only when the STB has received Region 5 rating data. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the LOCK menu option.
38 206-4147 Select the Input Source 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the INPUT menu option. Then, press ENTER . 2. Use the Up/Down arrows to select the appropriate input source (see descriptions below).
39 206-4147 Overview This document describes how to set up the STB1000 for Commercial Mode either while in the Embedded b -LAN™ (EBL) module’s Pass-through Mode or its Free-T o-Guest (FTG) Mode.
40 206-4147 Commercial Mode Setup for Master STB1000 T ypical STB1000 Installer Menu Adjust the settings for these Installer Menu items. 1. Set Installer Menu items. This step provides speci fi c instruction only on the Installer Menu items that should be set on a Master TV .
41 206-4147 After verifying the STB Setup, set Installer Menu item 028 CH. OVERIDE to 000.* Commercial Mode Setup for Master STB1000 (Cont.) DIGIT AL WXYZ MONO STEREO SAP 19-3 Custom T ext Label “WXYZ” created in 2-5-4 + MENU (Add Channel Label) Mode.
42 206-4147 Installer Menu T ypical STB1000 Installer Menu Use the Installer Menu to set up or change operational settings. Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing.
43 206-4147 Installer Menu (Cont.) Installer Menu Items 000 through 071 Menu Item Function V alue Range Default V alue Brief Description of Function and Comments 000 INST ALLER SEQ 0 ~ 3 0 Leave default set to 0. 001 POWER MANAGE 0 ~ 7 0 Sets number of hours of no activity before automatic shutoff.
44 206-4147 Installer Menu (Cont.) Installer Menu Items 073 through 1 19 Menu Item Function V alue Range Default V alue Brief Description of Function and Comments 073 CH NOT A VBLE 0 / 1 0 If set to 1 and Channel Override is 0, “NOT A V AILABLE” message is displayed when directly accessing a channel not in the favorite Channel List.
45 206-4147 Installer Menu (Cont.) Detailed Descriptions of Installer Menu Items 000 - INST ALLER SEQUENCE Speci fi es entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff.
46 206-4147 Installer Menu (Cont.) 016 - EN TIMER (Enable On/Off Timers) * If set to 1, the T imer function is available to the end user and enabled continuously . Set to 0 to disable On/Off Timers. Note: Clock must be set in order to use timers. 017 - ALARM * Gives the installer the option of making the Alarm function avail- able to the end user .
47 206-4147 Installer Menu (Cont.) 070 - FOR. CH-TIME (Channel-Time Display Foreground Color) Set according to Color Chart: 0 = Black 3 = Cyan 6 = Y ellow 1 = Blue 4 = Red 7 = White 2 = Green 5 = Violet Note: Applies only to “Channel Not Available” message if item 073 is set to 1 (enabled).
48 206-4147 Installer Menu (Cont.) • 6 = Scaler Model RJPs: DVI Mode Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP , only digital video is expected via the HDMI cable. Analog audio is provided via separate cable, from the source, connect- ed to an RJP AUDIO IN.
49 206-4147 Adding Channel Label Icons / Custom Channel Labels (2-5-4 + MENU Mode) Changing a Channel’ s Icon on the Master STB1000 1. Use Channel Up/Down to select the desired channel. 2. Use the Left/Right arrow keys to select the thin letter “ I ” on the Channel ID display .
50 206-4147 Use one of the following options to Learn and T each the Master STB1000 Setup: • Using a USB memory device • Using a TLL-1 100A clone programmer • Using a L T2002 clone programmer Each option is described in further detail on the pages that follow .
51 206-4147 Cloning Procedures Learning / T eaching a Master STB1000 Setup using a USB Memory Device Learn Setup from Master STB1000 1. Ensure the Master STB1000 is set up completely and the EBL is in Pass-through Mode. 2. Plug the USB memory device into the USB port on the Master STB1000 rear panel.
52 206-4147 Cloning Procedures (Cont.) Learning / T eaching a Master STB1000 Setup using a TLL-1 100A Clone Programmer W arning: Do not connect a clone programmer to the STB1000 MPI/GAME CONTROL port while the STB is in LodgeNet PPV Mode, as this will damage the clone programmer .
53 206-4147 Learn Setup from Master STB1000 1. Ensure the Master STB1000 is set up completely and the EBL is in Pass-through Mode. 2. If an analog channel is not available, direct tune the Master STB1000 to an Aux source, or select an Aux source, such as A V -1, from the Input Menu.
54 206-4147 Cloning Procedures (Cont.) Learning / T eaching a Master STB1000 Setup using a TLL-1 100A Clone Programmer (Cont.) T each Master STB1000 Setup to T arget STB1000 1.
55 206-4147 Cloning Procedures (Cont.) Learning / T eaching a Master STB1000 Setup using an L T2002 Clone Programmer Cloning is accomplished using the STB/clone programmer MPI ports for communication (see diagram). L T2002 Cloning Notes • Read the IMPORT ANT CLONING INFORMA TION on page 50 before beginning any cloning procedures.
56 206-4147 Cloning Procedures (Cont.) Learning / T eaching a Master STB1000 Setup using an L T2002 Clone Programmer (Cont.) Learn Setup from Master STB1000 1.
57 206-4147 Cloning Procedures (Cont.) Learning / T eaching a Master STB1000 Setup using an L T2002 Clone Programmer (Cont.) T each Master STB1000 Setup to T arget STB1000 1.
58 206-4147 FTG Mode of Operation FTG Con fi guration Overview The following steps outline local FTG configuration of individual STB1000s. Since these models are equipped with the EBL module, they can also be broadcast configured in FTG Mode by a Free-T o-Guest Management Appliance (FMA) head end device.
59 206-4147 CHANNEL PICTURE AUDIO TIME INPUT USB OPTION LOCK STB Setup Menus Shows that the EBL is in Pass-through Mode . Function Menu Shows that the EBL is in FTG Mode . While this menu is present on-screen, Installer Menu settings can ONL Y be accessed/changed using the FTG Configuration Application.
60 206-4147 FTG Mode of Operation (Cont.) FTG Channel Map Con fi guration Utility / FTG Channel Map Editor Overview DELETE Click to remove highlighted channel from FTG Channel Map. ADD After defining a new Logical Channel, click to add channel to the FTG Channel Map.
61 206-4147 FTG Mode of Operation (Cont.) FTG Installer Menu Con fi guration Utility Overview LEARN Click to transfer Installer Menu settings from the PTC to the EBL and FTG Configuration Application. * INST ALLER DEF AUL TS Click to reset FTG Installer Menu items shown in the FTG Configuration Application to defaults.
62 206-4147 Remote Jack Pack Setup RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093 RJP A V AILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP A V AILABLE to 001). See Installer Menu detailed descriptions for further information.
63 206-4147 External Equipment Setup Digital Audio Optical Connections / Component Connections Digital Audio Optical Connections 1. Connect an optical cable between the OPTICAL DIGIT AL AUDIO OUT con- nector on the STB1000 jack panel and the digital audio input connector on the external Digital Audio Ampli fi er System.
64 206-4147 .......... COMPONENT IN VIDEO AUDIO R L UPDA TE RESET AUDIO (RGB/DVI) P B Y P R ..... .... .......... 2 1(DVI) DIGIT AL VIDEO IN OPTICAL DIGIT AL AUDIO OUT REMOTE CONTROL OUT SPEAKER OUT 8 RJP INTERF ACE RGB IN VIDEO R -AUDIO- L/MONO AV IN 1 RGB(PC) .
65 206-4147 External Equipment Setup (Cont.) Composite Connections L R VIDEO COMPONENT IN VIDEO AUDIO R L UPDA TE RESET AUDIO (RGB/DVI) P B Y P R ..... .... .......... 2 1(DVI) DIGIT AL VIDEO IN OPTICAL DIGIT AL AUDIO OUT REMOTE CONTROL OUT SPEAKER OUT 8 RJP INTERF ACE RGB IN VIDEO R -AUDIO- L/MONO A V IN 1 RGB(PC) .
66 206-4147 Reference: Upgrading STB Software using a USB Memory Device Checking the Software V ersions Note: This function is not accessible while the TV is in FTG or PPV Mode.
67 206-4147 Reference: Downloading a Splash Screen using a USB Memory Device Splash Screen Image File Guidelines • The splash screen image must be a 24-bit (RGB 8 x 8 x 8) BMP . • The image should be no larger than 3 MB. • The ideal resolution for the image is 1366 x 768 pixels.
68 206-4147 Reference: RS-232 Display Panel Requirements DB9 Male LG monitors/displays listed below require an RS-232 serial null-modem DB9 cable with female connectors at each end.
69 206-4147 Reference: Display Panel T ype Speci fi cations The following table identifies the Installer Menu item 1 13 P ANEL TYPE setting for each of the compatible monitors/TVs listed in the “RS-232 Display Panel Requirements” Reference.
70 206-4147 Reference: STB1000 Aux Input Con fi guration DIRECT ACCESS T uning STB ENABLE MPI DA T A ST ART AUX SOURCE ASSIGN- MENT Installer Menu MPI DA T A ST A TUS TYPE 0x41 SOURCES ENABLED (R/W) .
71 206-4147 Reference: STB1000 Camport Auto Sense Operation The Camport Auto Sense function is enabled when: 1. Installer Menu item 034 CAMPORT EN is set to 1 AND 2. Installer Menu item 040 AUTO CAMPORT is enabled (1). Selectable : Can be accessed with INPUT key , direct access, etc.
72 206-4147 Reference: b -LAN Setup & Overview The control device at the head end, for example, an FMA-LG101 or a PCS150R, can control multiple STBs. When the STB1000 is first installed, it must be turned ON in order for the head end to be able to communicate with the b -LAN.
73 206-4147 Reference: RJP Model List and Input Auto-sensing Hierarchy RJP Model List Legacy Models Scaler Models RJP-101M RJP-201M RJP-101ML N/A RJP-1 10F N/A RJP-1 10FW N/A RJP-1 10W N/A RJP-1 10WBR.
74 206-4147 Reference: Programming the Installer Remote The Installer Remote can be programmed to operate most remote-controllable devices. Note that the Installer Remote may not control all models of other brands. 1. T est the remote to fi nd out whether it can operate other components without programming.
75 206-4147 Reference: Remote Control Codes Brand Code(s) AIW A 034 AKAI 016, 043, 046, 124, 125, 146 AMPRO 072 ANAM 031, 033, 103 AUDIO DYNAMICS 012, 023, 039, 043 BROKSONIC 035, 037, 129 CANON 028, .
76 206-4147 DVD Codes Brand Code(s) APEX DIGIT AL 022 ONKYO 008, 017 P ANASONIC 003, 009 PHILIPS 013 PIONEER 004, 026 PROCEED 021 PROSCAN 005, 006 RCA 005, 006 SAMSUNG 01 1, 015 SONY 007 THOMPSON 005, 006 TOSHIBA 008, 019 Y AMAHA 009, 018 ZENITH 010, 016, 025 Reference: Remote Control Codes (Cont.
77 206-4147 Reference: IR Codes Con fi guration of Frame 1st frame Repeat frame Lead Code Repeat Code Bit Description Frame Interval: Tf The waveform is transmitted as long as a key is depressed. Bit “0” Bit “1” Remote Control Connection Connect your wired remote control to the REMOTE CONTROL OUT port on the STB1000 jack panel.
78 206-4147 Code (Hexa) Function Note 08 POWER Remote Control Button (Power On/Of f) 0F TV Remote Control Button 0B INPUT Remote Control Button 0A SAP Remote Control Button AB RA TIO Remote Control Bu.
79 206-4147 T roubleshooting General T roubleshooting Some Quick and Easy T ips for Resolving Problems Software Problems Cannot direct enter channel number or “No Signal” appears. Channel not included in channel lineup in internal STB controller (PTC).
80 206-4147 Controller Quick Check Bad STB Ye s No No Ye s Press POWER on Installer Remote. STB responded? No Ye s End Bad STB Display panel ON? Ye s No Press VOLUME UP/ DOWN or MUTE key on LG Installer Remote. STB conected to AC Power? Plug into AC Power outlet.
81 206-4147 T roubleshooting (Cont.) Commercial Mode Check / FTG Operation T roubleshooting Press POWER on Installer Remote. STB responded? Bad STB Ye s No STB stopped responding or continued to respond? STB is in Commercial Mode. Stopped responding STB is not in Commercial Mode.
82 206-4147 T roubleshooting (Cont.) Clone Programmer T roubleshooting W arning: Do not connect a clone programmer to the STB1000 MPI/GAME CONTROL port while the STB is in LodgeNet PPV Mode, as this will damage the clone programmer .
83 206-4147 Specifications Dimensions Height: 1.77 inches (45 mm) Width: 13.875 inches (352.42 mm) Depth: 9.72 inches (247 mm) Weight: 6.4 pounds (2.90 kgrms) Environmental Storage Conditions T empera.
84 206-4147 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider . The end looks like a hex-shaped nut with a wire through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV . 300 TO 75 OHM ADAPTER A small device that connects a 2-wire 300 ohm antenna to a 75 ohm RF jack.
85 206-4147 Document Revision History / Notes Notes Document Revision History Date Description February 201 1 Revision A: New document Product documentation is available online at: www .LGsolutions.com/products . From the Products page, select TVs, Systems & Solutions , then Interface / Control Boxes & Cards , then STB1000 .
© Copyright 201 1, LG Electronics U.S.A., Inc. 206-4147 Revision A Broadcast Products Welcome to the LG family! We believe that you will be pleased with your new STB1000 HD Commercial Interface STB. Please read this warranty carefully , it is a “LIMITED WARRANTY” as defined under Federal Law .
An important point after buying a device LG Electronics STB1000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought LG Electronics STB1000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data LG Electronics STB1000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, LG Electronics STB1000 you will learn all the available features of the product, as well as information on its operation. The information that you get LG Electronics STB1000 will certainly help you make a decision on the purchase.
If you already are a holder of LG Electronics STB1000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime LG Electronics STB1000.
However, one of the most important roles played by the user manual is to help in solving problems with LG Electronics STB1000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device LG Electronics STB1000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
