Instruction/ maintenance manual of the product MW 71PY10 LG Electronics
Go to page of 48
MW -71PY10 MW -71PY10G OWNER’S MANUAL PLASMA MONITOR PLASMA MONITOR Please read this manual carefully before oper- ating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back of the set and quote this information to your dealer when you require service.
2 Plasma Monitor Warning/Caution W ARNING/CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE P AR TS INSIDE.
Owner ’s Manual 3 Safety Instructions IMPORT ANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appara- tus.
4 Plasma Monitor Safety Instructions 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel.
Owner ’s Manual 5 Contents Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2~4 Introduction Controls and Connection Options . . . . . . . . . .7~8 Remote Control Key Functions . . . . . . . . . . . . . .9 Installation Installation .
6 Plasma Monitor Introduction Introduction Introduction What is a Plasma Display Panel (PDP)? If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
Owner ’s Manual 7 Introduction Controls Controls INPUT MENU VOL TruSurround XT Front Panel Controls Front Panel Controls MENU Button INPUT Button VOLUME ( F , G ) Buttons E , D Buttons INDEX Switches LED Display on or off. Remote Control Sensor Power Indicator Illuminates red in standby mode, Illuminates green when the monitor is turned on.
8 Plasma Monitor Introduction Connection Options Connection Options REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE) AC INPUT DVI INPUT AUDIO INPUT RGB INPUT AUDIO COMPONENT COMPONENT RL VIDEO INPUT 1 I.
Owner ’s Manual 9 Introduction - When using the remote control, aim it at the remote control sensor on the monitor . - Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary .
10 Plasma Monitor Installation Installation Installation Ensure that the following accessories are included with your plasma display . If an accessory is missing, please contact the dealer where you purchased the product. Owner ’ s Manual 1.5V 1.5V Batteries Power Cord L I G H T IN P U T MODE PIP MUTE SLEEP VOL CH WIN.
Owner ’s Manual 11 Installation 4 inches 4 inches 4 inches 4 inches 2 inches W W all Mount Installation all Mount Installation For proper ventilation, allow a clearance of 4 ” on each side and 2 ” from the wall.
12 Plasma Monitor Installation External Equipment Connections External Equipment Connections NOTE: Not all cables shown are included with the plasma display . - T o avoid picture noise (interference), leave an adequate distance between the VCR and Monitor .
Owner ’s Manual 13 Installation External Equipment Connections External Equipment Connections - After subscribing to a cable monitor service from a local provider and installing a converter , you can watch cable TV program- ming.
14 Plasma Monitor Installation • Component Input ports T o get better picture quality , connect a DVD player to the component input ports as shown. - T o watch digitally broadcast programs, purchase and connect a digital set-top box.
Owner ’s Manual 15 Installation How to connect 1. T o get the best picture quality , adjust the PC graphics card to a 1280x1024, 60Hz. Resolutions over UXGA cannot be displayed. 2. Use the monitor ’ s RGB INPUT or DVI (Digital Visual Interface) port for video connections, depending on your PC connector .
16 Plasma Monitor Installation Monitor Display Specifications (RGB-PC / DVI-PC Mode) Resolution 720x400 640x480 800x600 848x480 Horizontal Frequency(KHz) 31.469 37.927 31.469 35.000 37.861 37.500 43.269 35.156 37.879 46.875 53.674 49.725 31.500 35.000 37.
Owner ’s Manual 17 Installation HDMI HDMI - HDMI TM , the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC." - This monitor can receive the High-Definition Multimedia Interface(HDMI).
18 Plasma Monitor Operation Operation Operation Menu Language Selection Menu Language Selection T T urning on the Monitor urning on the Monitor T urning on the Monitor just after installation 1. Connect power cord correctly . At this moment, the Monitor is switched to standby mode.
Owner ’s Manual 19 Operation 1. Press the APC button repeatedly to select the picture appearance setup option as shown below . APC (Auto Picture Control) APC (Auto Picture Control) - T o initialize values (reset to default settings), select the Normal option.
20 Plasma Monitor Operation - Y ou can adjust picture contrast, brightness, color, sharpness, and tint to the levels you prefer . 1. Press the MENU button and then use D / E button to select the PICTURE menu. 2. Press the G button and then use D / E button to select the desired picture option ( Contrast , Brightness , Color , Sharpness or Tint ) .
Owner ’s Manual 21 Operation Off Sound Menu Options Sound Menu Options 1. Press the DASP button repeatedly to select the appropriate sound setup as shown below . DASP DASP (Digital (Digital Auto Sound Processing) Auto Sound Processing) 1. Press the MENU button and then use D / E button to select the SOUND menu.
22 Plasma Monitor Operation - T imer function operates only if current time has already been set. - Off-T imer function overrides On-Timer function if they are set to the same time. - If you do not press any button within 2 hours after the monitor turns on with the On T imer function, the monitor will automatically revert to standby mode.
Owner ’s Manual 23 Operation Special Menu Options Special Menu Options Key Lock Key Lock - The monitor can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing by disabling the front panel controls.
24 Plasma Monitor Operation Special Menu Options continued Special Menu Options continued PIC- TURE SOUND TIMER SPECIAL SCREEN PIP/DW Prev. Menu T o start Language Key lock ISM Method Low power Set ID Demo G Index PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Prev.
Owner ’s Manual 25 Operation Auto Auto Adjustment Adjustment - RGB (PC) mode only; This function doesn ’ t work for RGB-DTV . - Automatically adjusts picture position and minimizes image shaking. - After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment.
26 Plasma Monitor Operation 1 4 ▲ ▼ ◀▶ 2-Split zoom ▲ ▼ ◀▶ 12 5 4 4-Split zoom ▲ ▼ ◀▶ 12 3 4 5 6 7 89 9-Split zoom Manual Configure (RGB-PC mode only) Manual Configure (RGB-PC .
Owner ’s Manual 27 Operation 1. Press the MENU button and then use D / E button to select the SCREEN menu. 2. Press the G button and then use D / E button to select Reset . 3. Press the G button. • Y ou can initialize Manual config., Position, Split zoom, PIP size, PIP posi- tion, PIP transparency and sub picture size for DW .
28 Plasma Monitor Operation Screen Screen Adjustments (V Adjustments (V ideo1-2 and Component 480i mode only) ideo1-2 and Component 480i mode only) - Use this function to correct jittering or picture instability while viewing a video tape. 1. Press the MENU button and then use D / E button to select the SCREEN menu.
Owner ’s Manual 29 Operation W W atching PIP atching PIP - PIP lets you view 2 dif ferent inputs (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - This function doesn ’ t work for RGB-DTV(1080p).
30 Plasma Monitor Operation Selecting a Source for the DW Selecting a Source for the DW W W atching DW atching DW Press the DW button repeatedly to select one of the DW options. Sub Picture Size Sub Picture Size Adjustment Adjustment Press the WIN.SIZE button.
Owner ’s Manual 31 External Control Device Setup No. Pin Name 1 No Connection 2 RXD (Receive data) 3 TXD (Transmit data) 4 DTR (DTE side ready) 5 GND 6 DSR (DCE side ready) 7 RTS (Ready to send) 8 C.
32 Plasma Monitor External Control Device Setup T ransmission * [Command 1]: k, j, m * [Command 2]: T o control PDP set. * [Set ID]: Y ou can adjust the set ID to choose desired moni- tor ID number in Special menu. Adjustment range is 1 ~ 99. When selecting Set ID ‘ 0 ’ , every con- nected PDP set is controlled.
Owner ’s Manual 33 External Control Device Setup 02. Input Select (Command 2:b) (Main Picture Input) G T o select input source for the Monitor . Y ou can also select an input source using the INPUT button on the Monitor's remote control.
34 Plasma Monitor External Control Device Setup 13. Remote Control Lock Mode (Command2:m) G T o lock the remote control and front panel controls on the monitor T ransmission [k][m][ ][Set ID][ ][Data].
Owner ’s Manual 35 External Control Device Setup 20. Color T emperature (Command2:u) G T o adjust color temperature. Y ou can also adjust ACC in the Picture menu. T ransmission Data 0: Cool 1: Normal 2: W arm [k][u][ ][Set ID][ ][Data][Cr] Acknowledgement [u][ ][Set ID][ ][OK][Data][x] 17.
36 Plasma Monitor External Control Device Setup 23. ISM Method (Command2:p) G T o avoid having a fixed image remain on screen. T ransmission Data 0: Normal 1: White wash 2: Orbiter 3: Inversion [j][p][ ][Set ID][ ][Data][Cr] Acknowledgement [p][ ][Set ID][ ][OK][Data][x] 26.
Owner ’s Manual 37 IR Code G Connect your wired remote control to the Remote Control port on the Monitor . G Output waveform Single pulse, modulated with 37.
38 Plasma Monitor IR Code Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 SLEEP MUTE POWER VOL+ VOL- CH+ CH- APC DASP ENTER ( Á ) AII INPUT SELECT MENU ARC Split Zoom Window Position Window Size F G D E EXIT PIP XD PIP Input DW Video HDMI Key lock Index Auto config.
Owner ’s Manual 39 Programming the Remote G The remote control is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable devices of other manufacturers. Note that the remote control may not control all models of other brands.
40 Plasma Monitor Programming the Remote Programming Codes Programming Codes VCRs VCRs CA CA TV TV AIWA 034 AKAI 016 043 046 124 125 146 AMPRO 072 ANAM 031 033 103 AUDIO DYNAMICS 012 023 039 043 BROKS.
Owner ’s Manual 41 Programming the Remote Audio Audio APEX DIGIT AL 022 DENON 020 014 GE 005 006 HARMAN KARDON 027 JVC 012 LG 001 010 016 025 MAGNA VOX 013 MARANTZ 024 MITSUBISHI 002 NAD 023 ONKYO 0.
42 Plasma Monitor T roubleshooting Checklist No output from one of the speakers • Adjust Balance in the Sound menu. (Refer to p.21) Unusual sound from inside the monitor • A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or of f and does not indicate a fault with the monitor .
Owner ’s Manual 43 Specifications • The specifications shown above may change without notice for quality improvement. Product Specifications Product Specifications MODELS Width (inches / mm) Heigh.
44 Plasma Monitor Notes Notes Notes.
Owner ’s Manual 45 Notes Notes Notes.
Y our LG Plasma Display Panel will be repaired or replaced in accordance with the terms of this w arranty , at LGE’s option, if it proves to be defective in material or workmanship under normal use,.
TO CONTACT THE LGE CUSTOMER SERVICE CENTER BY MAIL: LGE Customer Interactiv e Center P .O. Box 240007 201 James Record R oad Huntsville, Alabama 35824 http://www .lgservice.com FOR SERVICE: Before you call for warranty service, check your operating guide – you may avoid a service call.
MW -71PY10 MW -71PY10G OWNER’S MANUAL PLASMA MONITOR PLASMA MONITOR Please read this manual carefully before oper- ating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back of the set and quote this information to your dealer when you require service.
An important point after buying a device LG Electronics MW 71PY10 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought LG Electronics MW 71PY10 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data LG Electronics MW 71PY10 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, LG Electronics MW 71PY10 you will learn all the available features of the product, as well as information on its operation. The information that you get LG Electronics MW 71PY10 will certainly help you make a decision on the purchase.
If you already are a holder of LG Electronics MW 71PY10, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime LG Electronics MW 71PY10.
However, one of the most important roles played by the user manual is to help in solving problems with LG Electronics MW 71PY10. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device LG Electronics MW 71PY10 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
