Instruction/ maintenance manual of the product GR-S552 LG Electronics
Go to page of 34
CAUTION BEFORE SERVICING THE UNIT, READ THE "SAFETY PRECAUTIONS" IN THIS MANUAL. MODEL: GR-S552 / GR-S592 REFRIGERATOR SERVICE MANUAL http://biz.
CONTENTS ............................................................................................................................................................................. 2 SERVICING PRECAUTIONS.............................................
- 3 - Air Recharging in Compressor T est the refrigeration by connecting it electrically before refilling operation. It is necessary to ascertain the function of the motor-compressor and identify the defects immediately .
- 4 - ITEMS SPECIFICA TIONS FREEZER 1 14 NET CAP ACITY REFRIGERA TOR 306 TOT AL 420 DIMENSIONS (mm) 755(W) X 689(D) X 1777(H) NET WEIGHT (kg) 79 COOLING SYSTEM Fan Cooling TEMPERA TURE CONTROL Micom C.
- 5 - 2-1 FEA TURE CHART NOTE : This is a basic model. The shape of refrigerator is subject to change. 2. P ARTS IDENTIFICA TION Egg Storage Rack Freezer Door Rack Freezer Temperature Control Dial Leveling Screw Vegetable Drawer Used to keep fruits and vegetables, etc.
- 6 - 3-1 DOOR ● Freezer Door 1. Remove the hinge cover by pulling it upwards. 2. Loosen hexagonal bolts fixing the upper hinge to the body and lift the freezer door . 3. Pull out the door gasket to remove from the door foam Ass'y . ● Refrigerator Door 1.
- 7 - 3-4 DEF' CONTROL ASSY Def control ASM consists of Defrost Sensor and FUSE–M. Defrost Sensor functions to defrost automatically and it is attached to the Evaporator and the metal side of the case senses T emp. Fuse-M is a kind of safety device for preventing over- heating of the Heater when defrosting.
- 8 - 4-1 COMPRESSOR 4-1-1 Role The compressor inhales low temperature and low pressure gas evaporated from Evaporator of the Refrigerator , and condenses this gas to high temperature and high pressure gas, and then plays delivering role to Condenser .
- 9 - 4-3 OLP (OVER LOAD PROTECTOR) 4-3-1 Definition of OLP (1) OLP (OVER LOAD PROTECTOR) is attached to Hermetic Compressor and protects Motor by cutting off current in Compressor Motor by Bimetal in the OLP in case of over-rising temperature.
- 10 - 6-1 COMPRESSOR AND ELECTRIC COMPONENTS 6. TROUBLESHOOTING 1 2 3 4 5 2 5 5 3 5 4 5 5 1 4 3 YES YES YES YES NO NO YES YES YES NO NO NO Power Source. Remove the PTC-Starter from the Compressor and measure the voltage between T erminal C of Compressor and T erminals 5 or 6 of PTC.
- 11 - 6-2 PTC AND OLP 6 5 3 4 YES NO Normal operation of Compressor is impossible or poor . Separate the PTC from Compressor and measure the resistance between No.
- 12 - 6-3 ANOTHER ELECTRIC COMPONENTS ▼ Cooling is impossible Compressor doesn't run. Running state of Compressor is poor . Check a starting voltage. Check if current flows to the following components. a. Thermistor b. Starting devices c. OLP d.
- 13 - COMPLAINT POINTS TO BE CHECKED REMEDY Cooling is • Is the power cord unplugged from the outlet? • Plug to the outlet. impossible. • Check if the power S/W is set to OFF . • Set the switch to ON. • Check if the fuse of power S/W is shorted.
- 14 - 6-5 REFRIGERA TING CYCLE ▼ T roubleshooting Chart ▼ Leakage Detection Observe discharging point of refrigerant which may be in oil discharging part in compressor and hole of evaporator . YES YES Whether Compressor runs or not. Whether frost forms or not in Evaporator .
- 15 - NO. ITEMS CONTENTS AND SPECIFICA TIONS REMARKS WELDING (1) H 30 ROD (1) • Chemical Ingredients • Recommend H34 containing 34% Ag in the (1) • Ag: 30%, Cu: 27%, Zn: 23%, Cd: 20% • Service Center . (1) • Brazing T emperature: 710~840°C (2) Bcup-2 (1) • Chemical Ingredients (1) • Cu: About 93% (1) • P: 6.
The following description is basically for GR-S552/GR-S592. For the other models, refer to the diagram of the entire PCB circuit. 7-1 FUNCTION 7-1-1 FUNCTION 1.
7-1-4 DEFROSTING 1. The defrosting is performed each time when the total running time of the compressor reaches 7 hours. 2. After the power is turned on (or restored after a power failure), the defrosting starts when the total running time of the compressor reaches 4 hours.
7-1-6 ERROR DIAGNOSTIC MODE 1. The error diagnostic mode allows the SVC when a fault that may affect the performance of the product occurs while operating the product. 2. Even if the function control button is pushed when an error occurs, the function will not be performed.
7-2 PCB FUNCTION 7-2-1 POWER CIRCUIT The secondary part of the TRANS is composed of the power supply for the display and relay drive (12Vdc) and that for the MICOM and IC (5Vdc). The voltage for each part is as follows. V A1 is a part for preventing the over voltage and noise.
7-2-2 OSCILLA TION CIRCUIT This circuit is to generate the base clock for calculating time and the synchro clock for transmitting data from and to the inside logic elements of the IC1(MICOM). Be sure to use the authentic parts since the calculating time by the IC1 may be changed or it will not work if the OSC1 SPEC is changed.
7-2-4 LOAD DRIVE CIRCUIT 1. Load Drive Condition Check - 21 - Load T ype Measurement Location (IC5) No. 16 No. 13 No. 15 No. 14 No. 12 ON 1V or below Condition OFF 12V Comp Defrosting Heater Freezer F.
7-2-5 TEMPERA TURE SENSOR CIRCUIT The upper CIRCUIT reads REFRIGERA TOR temperature and DEF-SENSOR temperature for defrosting into MICOM. OPENING or SHORT state of each TEMPERA TURE SENSOR are as follows. 7-2-6 DOOR OPEN DETECTION CIRCUIT - 22 - SENSOR CHECK POINT NORMAL(-30 °C ~ 50 °C) SHORT -CIRCUITED OPEN Refrigerator Sensor POINT V oltage 0.
- 23 - 7-2-7 TEMPERA TURE COMPENSA TION & OVERCOOLING/UNDERCOOLING COMPENSA TION CIRCUIT 1. Refrigerator T emperature Compensation ➧ T able of T emperature Compensation by adjusting the resistance (Difference with the current temperature) E.
7-2-8 KEY BUTTON INPUT & DISPLA Y LIGHT ON CIRCUIT ➧ The circuit shown above is to determine whether a function control key on the operation display is pushed and to turn on the corresponding function indication LED. The drive type is the scan type.
- 25 - 7-3 RESIST ANCE SPECIFICA TION OF SENSOR • The resistance of SENSOR has ± 5% common difference. • Measure the resistance of SENSOR after leaving it over 3 minutes in measuring temperature. This postponing is necessary because of perceiving speed.
- 26 - 7-4 TROUBLE SHOOTING • Replace PCB when no trouble after checking the contents of trouble. CLASSIFICATION STATE OF TROUBLE POINT BE CHECKED CHECKING METHOD CONTENT REMEDY POWER SOURCE 1. All the DISPLAY 1. FREEZER/ FREEZER/REFRIGERATOR POWER SOURCE is poor Certify Fuse.
- 27 - CLASSIFICATION STATE OF TROUBLE POINT BE CHECKED CHECKING METHOD CONTENT REMEDY COOLING is poor. REFRIGERATOR 1. FREEZER TEMPERATURE See "FREEZER Certify the attaching state TEMPERATURE is is normal? TEMPERATURE is poor". of DOOR. poor.
7-5 MAIN PWB ASS'Y AND P ARTS LIST 7-5-1 MAIN PWB ASS'Y - 28 - 1. R-B52DZ/R-B55DZ.
7-5-2 REPLACEMENT P ARTS LIST - 29 -.
7-5-3 PWB ASS'Y , DISPLA Y AND P ARTS LIST - 30 -.
7-6 PWB DIAGRAM - 31 -.
- 32 -.
- 33 - 8. EXPLODED VIEW 104A 106A 310A 308A 314A 307A 309A 312A 328B 315A 281C 281B 281A 282A 282B 103C 318A 317A 304A 323B 328A 329C 420A 319A 105A 315B 327A 315C 319C 106A 283B 120A 158F 329D 409B 1.
* : optional parts - 34 - 151A 151A 155K 154A 233B * 149C * 149C * 140A * 149A 241A 205A or 205A or 241D 241C 235A 205A 205A * 131A 405C 404A 405C 405A * 131C 233A 230A 203A 200A 201A * 136A * 136B * .
An important point after buying a device LG Electronics GR-S552 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought LG Electronics GR-S552 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data LG Electronics GR-S552 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, LG Electronics GR-S552 you will learn all the available features of the product, as well as information on its operation. The information that you get LG Electronics GR-S552 will certainly help you make a decision on the purchase.
If you already are a holder of LG Electronics GR-S552, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime LG Electronics GR-S552.
However, one of the most important roles played by the user manual is to help in solving problems with LG Electronics GR-S552. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device LG Electronics GR-S552 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
