
PLASMA TV OWNER’S MANUAL 42PQ20 50PQ20 42PQ30 50PQ30 42PQ31 50PQ31 42PQ60 50PQ60 50PS30 50PS60
Please read this manual carefully before operating your set and retain it for future reference. The model and serial number of the TV is located on the back and one side of the TV. Record it below should you ever need service.
Serial:
1-800-243-0000 USA, Consumer User
This product qualifies for ENERGY STAR in the “fac- tory default (Home Use mode)” setting and this is the setting in which power savings will be achieved.
1-888-865-3026 USA, Commercial User 1-888-542-2623 CANADA
LG Customer Information Center
Changing the factory default picture setting or enabling other features will increase power consumption that could exceed the limits necessary to quality for Energy Star rating.
www.lgusa.com / www.lg.ca
www.lgusa.com / www.lg.ca / www.lgcommercial.com

WARNING / CAUTION
To prevent fire or shock hazards, do not expose this product to rain or moisture.
DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO
Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera- ture accompanying the appliance.
receiver. - Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Operation is subject to the following two condi- tions: (1) This device may not cause (harmful) interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (of the device).
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product

IMPORTANT SAFETY INSTRUCTIONS
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Do not use this apparatus near water.
Only use attachments/accessories specified by the manufacturer.
Clean only with dry cloth.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus com- bination to avoid injury from tip-over.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.
Unplug this apparatus during lighting storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

Never touch this apparatus or antenna during a thunder or lighting storm.
When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.
Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something.
CAUTION concerning the Power Cord: It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC out- let). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable.
"As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH" (Except 42/50PQ30C, 50/60PS60C)
Power Supply Short-circuit · Breaker

ANTENNAS Outdoor antenna grounding If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of over- head power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna dis- charge unit, connection to grounding elec- trodes and requirements for the grounding electrode. Antenna grounding according to the National Electrical Code, ANSI/NFPA 70
Ventilation Install your TV where there is proper ventila- tion. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places.
If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center.
Do not press strongly upon the panel with hand or sharp object such as nail, pencil or pen, or make a scratch on it.
Keep the product away from direct sunlight.
Pince de mise à la terre
Fil d entrée d antenne
Décharge d antenne (section 810-20 du NEC)
Conducteur mis à la terre (section 810-21 du NEC)
Pince de mise à la terre
Système d électrode de mise à la terre (article 250, section H du NEC)
Cleaning When cleaning, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
Moving Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV.
Équipement électrique


Manufactured under license from Dolby Laboratories. “Dolby “and the double-D symbol are trademarks of Dolby Laboratories.
is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.
This TV contains the detailed calibrations necessary for professional certification by the Imaging Science Foundation. The resulting ISF “day” and “night” modes will then be accessible by the user to experience the best their LG HDTV has to offer. CALIBRATE LIKE A PRO: Sophisticated and detailed calibrations can be made through the ISFccc mode. Detailed calibration requires a licensed technician. Please contact your local dealer to inquire about an ISF certified technician.
THX Cinema mode is recommended for watching movies. Designed for use in a dark room. (This feature is not available for all models.)
High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions.
HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing."
for an extended period, it can become permanently imprinted on the screen. This phenomenon is known as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.
(2 or more hours for LCD, 1 or more hours for Plasma).
areas of your TV if you use the 4:3 aspect ratio setting for an extended period.

ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below.
Q. MENU MENU
SOUND
RATIO
POWER
PICTURE
SLEEP
INPUT
AV MODE RETURN
VOL CH
INFO
FAV
AV MODE ENERGY SAVING
INPUT POWER
MUTE
P A G E
LIST
FLASHBK
VOL CH
MUTE
FLASHBK
P A G E
Q.MENU
FREEZE RATIO
RETURN
1.5V 1.5V
MARK
FAV
Owner’s Manual Power Cord Remote Control,
Bolts for stand assembly
(Refer to P.11)
(Refer to P.11)

Option Extras * Wipe spots on the exterior only with the polishing cloth.
When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain stan- dards compliance.
* Do not wipe roughly when removing stain. Excessive pressure may cause scratch or discoloration. Polishing Cloth (Not included with all models)

FRONT PANEL INFORMATION

G When the TV cannot be turned on with the remote control, press the (power) button on the TV. (The remote control will not work when the (power) button on the TV is switched off. )
Intelligent Sensor Adjusts picture according to the surrounding conditions. Remote Control Sensor
Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on.
Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on.


Remote Control Sensor Intelligent Sensor Adjusts picture according to the surrounding conditions.
Remote Control Sensor Intelligent Sensor Adjusts picture according to the surrounding conditions.
Power/Standby Indicator Illuminates red in standby mode. Illuminates white when the TV is switched on and goes out slowly .

50/60PS60, 50/60PS60C
BACK PANEL INFORMATION

HDMI/DVI IN, HDMI IN Digital Connection. Supports HD video and Digital audio. Doesn’t support 480i. Accepts DVI video using an adapter or HDMI to DVI cable (not included)
COMPONENT IN Analog Connection. Supports HD. Uses a red, green, and blue cable for video & red and white for audio.
AV (Audio/Video) IN Analog composite connection. Supports standard definition video only (480i). S-VIDEO Better quality than standard composition. Supports standard definition video only (480i).
OPTICAL DIGITAL AUDIO OUT Optical digital audio output for use with amps and home theater systems. Note: In standby mode, this port doesn’t work.
RS-232C IN (CONTROL & SERVICE) PORT Used by third party devices.
ANTENNA/CABLE IN Connect over-the air signals to this jack. Connect cable signals to this jack.
AUDIO IN (RGB/DVI) 1/8” headphone jack for analog PC audio input. RGB IN (PC) Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable).
USB IN Used for viewing photos and listening to MP3.
Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power.
REMOTE CONTROL IN PORT For a wired remote control.

Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.


Assemble the TV as shown.





Fix the 4 bolts securely using the holes in the back of the TV. 3





Protection Cover
After removing the stand, install the included protection cover over the hole for the stand. Press the PROTECTION COVER into the TV until you hear it click.
G When assembling the stand, make sure to distinguish
and assemble the front and rear side of the stand correctly.
G When assembling the desk type stand, check
whether the bolt is fully tightened. (If not tight- ened fully, the product can tilt forward after the product installation). If you tighten the bolt with excessive force, the bolt can deviate from abra- sion of the tightening part of the bolt.











DESKTOP PEDESTAL INSTALLATION
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.


4 inches 4 inches
G Do not mount near or above any type of heat source. CAUTION
G Ensure adequate ventilation by following the clearance recommendations.
(This feature is not available for all models.)
After installing the TV, you can adjust the TV manually to the left or right direction by 20 degrees to suit your viewing position.

After connecting the cables as necessary, install CABLE HOLDER as shown and bundle the cables.
4 inches · 4 inches

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. LG recommends that wall mounting be performed by a qualified professional installer.
VESA (A * B)
A
B
42PQ20, 42PQ30, 42PQ31, 42PQ30C, 42PQ60,42PQ10, 50PQ20, 50PQ30, 50PQ31, 50PQ30C, 50PQ60, 50PS30, 50PS60, 50PS60C, 50PQ10, 50PS10
AW-50PG60MS
60PS60, 60PS60C, 60PS10
600 * 400 M8 4
AW-60PG60MS
NOTE !
G Screw length needed depends on the wall mount
screws may differ depending on their specifica- tions.
used. For further information, refer to the instruc- tions included with the mount.
G Do not use screws that do not comply with the
VESA standard screw specifications. Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. LG is not liable for these kinds of accidents.
G Standard dimensions for wall mount kits are shown
in the table.
G When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for assembly are provided.
G Do not use screws longer then the standard dimen-
G LG is not liable for TV damage or personal injury
sion, as they may cause damage to the inside to the TV.
when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installa- tion instructions.
G For wall mounts that do not comply with the VESA
standard screw specifications, the length of the
G Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric
shock.

SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.

*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.
the rope so it becomes horizontal between the wall and the product.

G Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
G To use the TV safely, make sure that the height of the bracket on the wall and the one on the TV are


Wall Antenna Socket or Outdoor Antenna without a Cable Box Connection. For optimum picture quality, adjust antenna direction if needed.
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Be careful not to bend the copper wire when connecting the antenna.


This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

Connect the video outputs (Y, PB, PR) of the digital set- top box to the COMPONENT IN VIDEO 1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red).
Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO 1 jacks on the TV. 2
(Refer to the owner’s manual for the digital set-top box. operation)
Y, CB/PB, CR/PR Supported Resolutions



1. How to connect
OPTICAL DIGITAL AUDIO OUT
AUDIO (RGB/DVI)
Connect the digital set-top box to HDMI/DVI IN 1, 2, 3 or 4 (Only 42/50PQ60, 50/60PS60, 50/60PS60C) jack on the TV.
(CONTROL & SERVICE)
RS-232C IN
RGB(PC)
No separate audio connection is necessary. HDMI supports both audio and video.
2. How to use
(Refer to the owner’s manual for the digital set-top box.)
50/60PS60, 50/60PS60C) input source on the TV using the INPUT button on the remote control.
NOTE !
G Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
Horizontal Vertical Frequency(KHz) Frequency(Hz)
31.469 59.94 31.50 60.00
44.96 59.94 45.00 60.00
33.72 59.94 33.75 60.00
27.00 24.00 33.75 30.00 67.43 59.94 67.50 60.00

DVI to HDMI Connection
1. How to connect

Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1, 2, 3 or 4 (Only 42/50PQ60, 50/60PS60, 50/60PS60C) jack on the TV.
AUDIO IN (RGB/DVI)

Connect the audio output of the digital set-top box to the AUDIO IN (RGB/DVI) jack on the TV.
ual for the digital set-top box.)
50/60PS60, 50/60PS60C) input source on the TV using the INPUT button on the remote control.

G A DVI to HDMI cable or adapter is required for this
connection. DVI doesn't support audio, so a separate audio connection is necessary.

Component Connection

Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO 1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red).
Connect the audio outputs of the DVD to the COMPONENT IN AUDIO 1 jacks on the TV.
Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below.


S-Video Connection

Connect the S-VIDEO output of the DVD to the S -VIDEO input on the TV.
Connect the audio outputs of the DVD to the AUDIO input jacks on the TV.
1. How to connect


Connect the HDMI output of the DVD to the HDMI/DVI IN 1, 2, 3 or 4 (Only 42/50PQ60, 50/60PS60, 50/60PS60C) jack on the TV.
No separate audio connection is necessary. HDMI supports both audio and video.
50/60PS60, 50/60PS60C) input source on the TV using the INPUT button on the remote control.

Antenna Connection
1. How to connect
AV IN 1
Connect the RF antenna out socket of the VCR to the ANTENNA/CABLE IN socket on the TV.
CABLE IN
ANT OUT
L R S-VIDEO VIDEO
Connect the antenna cable to the RF antenna in socket of the VCR.
Wall Jack
2. How to use
tune TV to the same channel number.
PLAY on the VCR. (Refer to the VCR owner’s manual.)

Composite (RCA) Connection

Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
G If you have a mono VCR, connect the audio cable
from the VCR to the AUDIO L/MONO jack of the TV.

Connect the S-VIDEO output of the VCR to the S -VIDEO input on the TV.
Connect the audio outputs of the VCR to the AUDIO input jacks on the TV.


and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.



Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors. (Video = yellow, Audio Left = white, and Audio Right = red)
L/MONO R AUDIO VIDEO USB IN HDMI IN 3
2. How to use
the INPUT button on the remote control.
input source on the TV.
Send the TV’s audio to external audio equipment via the Audio Output port.
Connect one end of the optical cable to the TV’s OPTICAL port of DIGITAL AUDIO OUT.
AUDIO (RGB/DVI)
Connect the other end of the optical cable to the digital audio input on the audio equipment.
(CONTROL & SERVICE)
Set the “TV Speaker option - Off” in the AUDIO menu. (G p.76). See the external audio equipment instruction manual for operation.
RGB(PC)
NOTE !
G When connecting with external audio equipment, such as
amplifiers or speakers, you can turn the TV speakers off in the menu. (G p.76)
G Do not look into the optical output port. Looking at the laser beam may damage your vision.
G Audio with ACP (Audio Copy Protection) function may block digital audio output.

USB CONNECTION
i.e)
DVI IN 3
EXTERNAL EQUIPMENT SETUP
AV IN 2
1. How to connect
Connect the USB device to the USB IN jack on the side of TV.
tion. (G p.50)

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
AUDIO IN (RGB/DVI)

Connect the VGA output of the PC to the RGB IN (PC) jack on the TV.
Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the TV.
AUDIO IN (RGB/DVI)
DVI to HDMI Connection


Connect the DVI output of the PC to the HDMI/DVI IN 1, 2, 3 or 4 (Only 42/50PQ60, 50/60PS60, 50/60PS60C) jack on the TV.
Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the TV.
50/60PS60, 50/60PS60C) input source on the TV using the INPUT button on the remote control.

NOTES ! Supported Display Specifications (RGB-PC, HDMI-PC)
Horizontal Vertical Frequency(KHz) Frequency(Hz)
42/50PQ30C, 42/50PQ60: To get the the best picture quality, adjust the PC graphics card to 1360x768.
31.468 70.08
31.469 59.94
the the best picture quality, adjust the PC graphics card to 1920x1080.
37.879 60.31
G Depending on the graphics card, DOS mode
48.363 60.00
may not work if a HDMI to DVI Cable is in use.
G In PC mode, there may be noise associated
47.78 59.87
with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
47.72 59.80
66.647 59.988
G Avoid keeping a fixed image on the screen for a
long period of time. The fixed image could become permanently imprinted on the screen.
G The synchronization input form for Horizontal
and Vertical frequencies is separate.
G Depending on the graphics card, some resolu-
tion settings may not allow the image to be positioned on the screen properly.

Selecting Resolution
You can choose the resolution in RGB-PC mode. The Position, Phase, and Size can also be adjusted.
Screen Move Prev.
1360 x 768 Auto config.
R G
Select the desired resolution.
Select PICTURE.
Select Screen (RGB-PC).
Select Resolution.
Prev. MENU
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, try using the manual settings or a differ- ent resolution or refresh rate on the PC.
Auto config. G
Select Yes. 4
Start Auto Configuration. 5
Select Screen (RGB-PC).
Select Auto config..

Adjustment for screen Position, Size, and Phase

If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This feature operates only in RGB-PC mode.
Select PICTURE.

Select Screen (RGB-PC).
vertical bars or stripes visible on the screen background. And the horizontal screen size will also change.
Select Position, Size, or Phase.
remove any horizontal noise and clear or sharpen the image of characters.
Make appropriate adjustments.


Returns Position, Size, and Phase to the default factory settings. This feature operates only in RGB-PC mode.
Select PICTURE.
Select Screen (RGB-PC).
Select Yes. 4

REMOTE CONTROL FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.

Select the remote operating mode: TV, STB or DVD.
Turns the TV on from standby or off to standby.
Opens the list of Quick Menu options. G p.38
Displays the main menu or clears all on-screen displays and returns to TV viewing.
Rotates through inputs. Also switches the TV on from standby. G p.45
Used to enter a program number for multiple program channels such as 2-1, 2-2, etc.
Controls USB menu (PHOTO LIST and MUSIC LIST). Controls the SIMPLINK compatible devices.
See a list of AV devices connected to TV. When you toggle this button, the SIMPLINK menu appears at the screen. G p.48-49
Changes the aspect ratio of the video. G p.58

Navigates the on-screen menus and adjusts the system settings to your preference.
Allows the user to move return one step in an interactive application or other user interaction function.
WATCHING TV / CHANNEL CONTROL
INFO
Displays channel information at the top of the screen.
Toggles through preset Video and Audio modes. G p.47
Adjusts the volume.
Scroll through the programmed Favorite channels. G p.43
MARK
Use to mark or unmark a photo/music G p.52
Switches the sound on or off. G p.34
Changes the channel.
Moves from one full set of screen information to the next one.
the batteries matching correct polarity.
new ones.
(Up/Down/Left · Right/ENTER)


Displays channel information at the top of the screen.
Toggles through preset Video and Audio modes. G p.47
Turns the TV on from standby or off to standby.
Rotates through inputs. Also switches the TV on from standby. G p.45
Moves from one full set of screen information to the next one.
Controls USB menu (PHOTO LIST and MUSIC LIST). Controls the SIMPLINK compatible devices.
Opens the list of Quick Menu options. G p.38
See a list of AV devices connected to TV. When you toggle this button, the SIMPLINK menu appears at the screen. G p.48-49
Changes the aspect ratio of the video. G p.58
Use to mark or unmark a photo/music G p.52

Used to enter a program number for multiple program channels such as 2-1, 2-2, etc.
LIST
Displays the channel list.
Tunes to the last channel viewed.
Navigates the on-screen menus and adjusts the system settings to your preference.
Displays the main menu or clears all on-screen displays and returns to TV viewing.
Allows the user to move return one step in an interactive application or other user interac- tion function.
batteries matching correct polarity.
with new ones.
NUMBER button · (Up/Down/Left · Right/ENTER)

WATCHING TV / CHANNEL CONTROL
TURNING ON TV
First, connect power cord correctly. At this moment, TV is in standby mode.
Select the viewing source by using the INPUT button on the remote control.
When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.
G If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
G If the TV is unplugged once or turn off with the (power) button on the TV, reset the Clock func- tion.
Press the CH ( or ) or NUMBER buttons to select a channel number. 1
Adjust the volume to suit your personal preference.
Press the VOL (+ or -) button to adjust the volume.
If you want to switch the sound off, press the MUTE button.
You can cancel the Mute function by pressing the MUTE or VOL (+ or -) button.
(Only 42/50PQ30C, 50/60PS60C) · (Except 42/50PQ30C, 50/60PS60C)

This Function guides the user to easily set the essential items for viewing the TV for the first time when pur- chasing the TV. It will be displayed on the screen when turning the TV on for the first time. It can also be acti- vated from the user menus.
in your home environment.
menu - Picture mode” manually while inspecting the TV, but the TV will automatically return to preset in- store mode after 5 minutes.
Factory defaults are set when you choose “Home Use”.
setting procedure is completed.
Select menu Language . 1
Step2. Mode setting
Select Home Use mode. 1
ENTER Selecting the environment. Choose the setting mode you want.
Store Demo Home Use
Select [Home Use] to use this TV at home.

Step3. Time setting
Select Auto or Manual.
Select desired time option.
Start Auto Tuning. 1
Check your antenna connection. The previous channel information will be updated during Auto Tuning.


Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.

QUICK MENU
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently.
SAP: Selects MTS sound (Analog signal).
Q.Menu
CH
1 Q. MENU
Display each menu.
Make appropriate adjustments.
Return to TV viewing.


Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list.

Select CHANNEL.
Select Auto Tuning.
control has been activated (Lock Menu). Use the password you set up in the Lock Menu to allow a channel search.
Select Yes.


If you select DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the quali- ty of the signal being received.
Select CHANNEL. 1

Select Manual Tuning.
Select DTV, TV, CADTV, or CATV.
control has been activated (Lock Menu). Use the password you set up in the Lock Menu to allow a channel search.
Select channel you want to add or delete.


When a channel number is deleted, it means that you will be unable to select it using CH , button during TV viewing. If you wish to select the deleted channel, directly enter the channel number with the NUMBER buttons or select it in the Channel Edit menu.
Select CHANNEL. 1
ENTER Select Channel Edit.
Select a channel.
Add or delete the channel.

CHANNEL LIST
You can check channels which are stored in the memory by displaying the channel list.
This padlock is displayed when the channel is locked with parental control
DTV 15-1
18-2 DTV
WATCHING TV / CHANNEL CONTROL
Displaying Channel List
Display the Channel List. 1
LIST
Selecting a channel in the channel list
Select a channel. 1
Switch to the chosen channel number. 2
Paging through a channel list
Turn the pages. 1
P A G E
CH
Return to TV viewing. 2
RETURN
Channel List · Exit

Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
Favorite Channels are a convenient feature that lets you quickly select channels of your choice without waiting for the TV to select through all the in-between channels. To tune to a favorite channel, press the FAV (Favorite) button repeatedly.

2 3 Select your desired channel. or
CH
WATCHING TV / CHANNEL CONTROL
Select Del/Add/Fav. 2 Q. MENU
3 Select Favorite.
4Q. MENU Return to TV viewing.
Display the Favorite channel list. 1 Displaying the favorite channel list
FAV
FAV
MARK
DTV
DTV 15-1
18-2 DTV
Selecting a channel in the favorite channel list
Select a channel. 1
Switch to the chosen channel number. 2
Paging through a favorite channel list
Turn the pages. 1
P A G E
CH
Return to TV viewing. 2
RETURN
Favorite List · or · Exit

BRIEF INFORMATION
Brief Info shows the present screen information.
Show the Brief Info on the screen.
RETURN Return to TV viewing
1 2 3 4 5 6 7
No Program Information.
Wed, Aug 21, 2009 10:10 AM 11:40 AM
Multilingual Caption 1080i MPAA PG CC
Multilingual : The program contains two or more audio services. Use the Q.MENU menu to select wanted Audio.
Caption : The program contains one or more caption services. Use the Q.MENU menu to select wanted Closed caption.
The original aspect ratio of the video is 4:3 The original aspect ratio of the video is 16:9 (wide)
4:3 16:9
480i 480p 720p 1080i 1080p
The video resolution is 720x480i The video resolution is 720x480p The video resolution is 1280x720p The video resolution is 1920x1080i The video resolution is 1920x1080p
V-Chip: The program contains V-Chip information. Refer to the LOCK menu: A (Age), D (Dialogue), L (Language), S (Sex), V (Violence), FV (Fantasy Violence)

Only these input signals which are connected to a TV can be activated and selected.

TV AV1 AV2 Component1 Component2
INPUT
INPUT
TV AV1 AV2 Component1
HDMI3 HDMI2 HDMI1 RGB-PC
HDMI3
Disconnected inputs are inactive (grayed out)

TV AV1 AV2 Component1 Component2
Select a desired input source (except TV). Then, you can select your desired Input Label with using Blue button. G p.46
ie) In case of changing the input label with using Blue button
If selecting Yes, you can select input source that you want to appreciate.
! New external device is connected. Do you want to enjoy this?
! Select input source that you want to appreciate.
AV2
cable broadcasts.
nition devices.
nal equipment.
Digital set-top box.


You can set a label for each input source when it's not in use.
With using OPTION menu
With using INPUT button


Select OPTION.
Select the source(except TV).
Select Input Label.
Select the label.
Select the label.

AV Mode toggles through preset Video and Audio settings.
(O n ly 50 / 60 P S 60 . 50/60PS60C)
WATCHING TV / CHANNEL CONTROL
Game Sport
1 AV MODE
Press the AV MODE button repeatedly to select the desired source.
“Picture Mode” and “Sound Mode” return to previous selected value.
watching movies.
watching sports events.
playing games.
Cinema or


Simplink allows you to control and play other AV devices connected with HDMI cable without additional cables and settings. This TV may work with devices with HDMI-CEC support, but only devices with the
logo are fully supported. SIMPLINK can be turned on and off in the user menus.


G Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of the SIM-
G When you switch the Input source with the INPUT button on the remote control, the SIMPLINK device will
G When you select a device with home theater functionality, the sound output automatically switches to the
home theater speakers and the TV speakers are turned off.
G If a connected SIMPLINK home theater system doesn't play the audio from the TV, connect the DIGITAL
AUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the back of the SIM- PLINK device with an OPTICAL cable.

out additional settings.
will change automatically to turn on mode. (A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does not provide this function) Note: To operate SIMPLINK, an HDMI cable over Version 1.3 with *CEC function should be used. (*CEC: Consumer Electronics Control).


Display SIMPLINK menu.
Select the desired device.
Control connected AV devices.
F G
F G
F G
SIMPLINK Menu
TV viewing: Switch to the previous TV channel regardless of the current mode. DISC playback: Select and play discs. When multiple discs are available, the titles of discs are conveniently displayed at the bottom of the screen. VCR playback: Control the connected VCR. HDD Recordings playback: Control recordings stored in HDD. Audio Out to Home Theater speak- er/Audio Out to TV: Select Home Theater speaker or TV speaker for Audio Out.

G When no device is con-
nected (displayed in gray)
G When a device is connected
(displayed in bright color)
F G

ENTRY MODES
When you connect a USB device, this screen is displayed automatically. In USB device, you can not add a new folder or delete the existing folder.
Connect the USB device to the USB IN jacks on the side of TV.
G In order to avoid losing the USB memory stick, use
the USB connector to fix the USB memory stick to the USB connector holder of the TV.
USB
USB Connector (sold separately)
Select Photo List or Music List.
- Fix the one end of the USB connector to
the USB memory stick and the other end to the USB connector holder.
Photo List Music List
Select the Eject USB menu before removing the USB device.
Select Eject USB.
Select Eject.
G Only a USB storage device is recognizable.
a storage device formatted as a different utility pro- gram which is not supported by Windows, it may not be recognized.
G If the USB storage device is connected through a USB
hub, the device is not recognizable.
G Please connect power to a USB storage device which
G A USB storage device using an automatic recognition
program may not be recognized.
requires an external power supply. If not, the device may not be recognized.
G A USB storage device which uses its own driver may
not be recognized.
G Please connect a USB storage device with cable is
offered by USB maker. If connected with cable is not offered by USB maker or an excessively long cable, the device may not be recognized.
G In case of a card reader, up to four memory cards are
concurrently recognizable.
G The recognition speed of a USB storage device may
depend on each device.
G Some USB storage devices may not be supported or
operate properly.
G Please do not turn off the TV or unplug the USB
device when the connected USB storage device is working. When such device is suddenly separated or unplugged, the stored files or the USB storage device may be damaged.
G The TV will display up to 128 characters of a files
name.
G Please backup important files because data on USB
device may be damaged. Data management is con- sumer's responsibility and as a result, the manufactur- er does not cover data damage.
G Only use a USB storage device which has normal
music files or image files.
G The recommended capacity is 1TB or less for a USB external
G Please use only a USB storage device which was for-
hard disk and 32GB or less for USB memory. Any device with more than the recommended capacity may not work properly.
matted as a FAT16, FAT32 or NTFS file system pro- vided with the Windows operating system. In case of
USB connector holder · USB Input Port

You can view .JPG files from USB storage devices. The On Screen Display on your model may be slightly different.

Screen Components


Photo Selection and Popup Menu


When you select a file (not folder), this PopUp menu is displayed.
G Mark All: Mark all photos on the screen.
Select the target folder or drive.

photo. When one or more photos are marked, you can view individual photos or a slide show of the marked photos. If no photos are marked, you can view all photos individually or all pho- tos in the folder in a slide show.
4 Select the desired Popup menu.

You can change the Photo List view so that it fills the screen. More operations are available in full screen mode.

Move Move Page Mark CH MARK PopUp Menu Exit


Move Move Page Mark CH MARK PopUp Menu Exit
The aspect ratio of a photo may change the size of the photo displayed on the screen in full size.
Select the target folder or drive.
Select the desired photos.
Show the Popup menu.
Select View.
The selected photo is displayed in full size.


Select the Slideshow, BGM,
(Rotate), Delete, Option, or Hide.
Slideshow BGM Delete Option Hide
slide show. If no photo is selected, all photos in the cur- rent folder are displayed during slide show.
G BGM: Listen to music while viewing photos in full size.
G (Rotate): Rotate photos.

G Delete: Delete photos.
Press F G to set the time interval between slides.
Folder.
... Music Folder
playing.
G Hide : Hide the menu on the full-sized screen.
ENTER button to display.
G This TV will not be able to decode
most JPEG images saved using the Progressive option.
1/17 · Slide Speed Fast · Cancel

You can use the Music List menu to play MP3 files form a USB storage device. This TV cannot play back copy-protected files. The On Screen Display on your model may be slightly different.

Screen Components


Music Selection and Popup Menu
Up to 6 music titles are listed per page.

Once a song finishes playing, the next selected one will be played. When there are no selected musics to play, the next one in the current fold- er will be played. If you go to a different folder and press the ENTER button, the current music in playback will stop.
a music finishes playing, the next selected one will be played automatically.
G Mark All: Mark all musics in the folder.
Move Move Page Mark CH MARK PopUp Menu Exit

file. If no music is marked, all the music in the folder will be played in sequence. When one or more music files are marked, the marked music files will be played in sequence. If you want to listen to only one song repeatedly, just mark that one file and play.

move across the screen when there is no user input to pre- vent a fixed image remaining on the screen for a extended period of time.

NOTE !
G When music is playing, is displayed in front of the music play time.
G A damaged or corrupted music file that does not play displays 00:00 as the play time.
G Music files with copy-protection will not play.
G Press ENTER, A , or RETURN button to stop the screen saver.
G This TV can not play music files less than 16 Kbytes.

PICTURE SIZE (ASPECT RATIO) CONTROL
This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV.
Q.Menu
16:9 Just Scan
Set By Program
Zoom Cinema Zoom
4:3
CH
PICTURE CONTROL
1 Q. MENU
Select the Aspect Ratio.
Select the desired picture format.
Return to TV viewing.
ly on the remote control.

16:9 Adjust the picture horizontally, in a linear pro- portion to fill the entire screen.
4:3 Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio.


Just Scan Normally the edges of video signals are cropped 1-2%. Just Scan turns off this cropping and shows the complete video. Notes: If there is noise on the edges of the original signal, it will be visible when Just Scan is activated. Just Scan operates only in DTV/CADTV/Component/HDMI-DTV/DVI-DTV (720p/1080i/1080p) input source.
Zoom Choose Zoom when you want to view the picture without any alteration. However, the top and bot- tom portions of the picture will be cropped.


Cinema Zoom Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging or reducing the picture, the image may become distorted.
Set by program Selects the proper picture proportion to match the source’s image.

(4:3 4:3) (16:9 16:9)




This feature lets you adjust the picture quality of the original image. Use this to calibrate the screen quality by adjusting the Black and White Level etc. You can calibrate the screen quality by easily following each step. When you adjust the image to Low, Recommended or High, you can see the example of the changes you made.
Set the screen above identical to the Recommended sample below.
Set the screen above identical to the Recommended sample below.
With Picture Wizard, you can adjust the picture quality of the original image.
Set the screen above identical to the Recommended sample below.
Set the screen above identical to the Recommended sample below.

Select (an) input(s) to apply the settings.
Set the screen above identical to the Recommended sample below.
TV
AV1
AV2
E
RGB-PC
HDMI1
HDMI2
HDMI3
Adjust Horizontal Sharpness. 8
HDMI4
PICTURE CONTROL
E
Select input source to apply the settings. 10
MARK
FAV
Save. 11
Set the screen above identical to the Recommended sample below.
The current adjustment value is saved to Expert1. !
E
Finish the Picture Wizard. 12
Adjust Vertical Sharpness. 9
step, the changes will not be saved to the TV.


It reduces the TV’s power consumption. The default factory setting complies with the Energy Star requirements and is adjusted to the comfort- able level to be viewed at home. You can increase the brightness of your screen by adjusting the Energy Saving level or by setting the Picture Mode. This feature is disabled in “Picture Mode-Cinema”.

Select Intelligent Sensor ( Select Low, Middle, or High.),
Off, Minimum, Medium or Maximum.

screen to the most suitable picture according to the surrounding conditions.

There are factory presets for picture settings available in the user menus. You can use a preset, change each setting manually.
Q.Menu
F 16:9 G
16:9
Cinema
Expert2
CH
Expert1
Game Sport
PICTURE CONTROL
1Q. MENU Select Picture Mode.
2 Select Vivid, Standard, Cinema (or Cinema), Sport, Game, Expert1or Expert2.
TURE menu.
of the video in the retail store. Strengthen the contrast, brightness, color and sharpness for vivid picture.
3Q. MENU Return to TV viewing.
viewing condition for the general user.
ing movies.
dynamic video and primary color (Ex, white, uni- form, grass, sky blue etc.) by realizing the opti- mal screen for sports.
speed in a fast gaming screen.
detail for video quality expert and general user.


Adjust the picture appearance to suit your preference and viewing situations. 50/60PS60, 50/60PS60C only: This feature is disabled in “Picture Mode- Cinema”.
Select PICTURE.

Select Contrast, Brightness, Sharpness, Color, or Tint.
Make appropriate adjustments.

of the video signal. You may use Contrast when the bright part of picture is saturated.
in the picture. You may use brightness when the dark part of the picture is saturated.
edges between the light and dark areas of the picture. The lower the level, the softer the image.


You can calibrate the screen for each Picture Mode or set the video value according to the special video screen. You can set the video seeing differently for each input. To reset to the factory default screen after making adjustments to each video mode, execute the “Reset” func- tion for each Picture Mode.

Select PICTURE.
Select Advanced Control.
Select your desired options.


By segmenting categories, Expert1 and Expert2 provide more categories which users can set as they see fit, offering the optimal picture quality for users. This may also be used be a professional to help optimize the TV performance in the environment the TV is in.

screen. The picture is improved by making bright parts brighter and dark parts darker.
hue, saturation and luminance so that red, blue, green and white look more vivid.
Low : Make dark and middle gray level area of the picture brighter. Medium: Express original picture levels. High: Make dark and middle gray level area of the picture darker.
Low: The reflection of the screen gets darker. High: The reflection of the screen gets brighter. Auto: Realizing the black level of the screen and set it to High or Low automatically.
HDMI or Component. Otherwise, 'Black level' is set to 'Auto'.
Standard: Displays standard color area. Wide: Mode to use and set the rich color area of the display.
The adjustment range is -50 - +50. b. Method :20 Point IRE - Pattern: Inner, Outer - IRE (Institute of Radio Engineers) is the unit to display the size of the video signal and can be
set among 5, 10, 15 - 95, 100. You can adjust Red, Green or Blue according to each setting. - Red/Green/Blue: The adjustment range is -50 - +50.
this does not affect other colors but can be used to selectively adjust the 6 color areas (Red/Green/Blue/Cyan/Mgt/Yellow). Color difference may not be distinctive even when you make the adjustments for the general video. Adjusts Red/Green/Blue/Yellow/Cyan, Magenta. - Red/Green/Blue/Yellow/Cyan, Magenta Color: The adjustment range is -30 -
+30. - Red/Green/Blue/Yellow/Cyan, Magenta Tint: The adjustment range is -30 - +30. - This feature is disable in RGB-PC and HDMI (PC) mode.


Settings of the selected picture modes return to the default factory settings.



A frozen still picture displayed on the screen for prolonged periods can result in a ghost image. You can use Orbiter to help prevent image sticking. The other two functions are for removing a ghost image.

Select OPTION.
problem, ISM is not necessary - set to Normal.
Select ISM Method.
ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a ghost image on the screen, the image will move every 2 min- utes.
Select Normal, Orbiter, Color Wash or White Wash.
screen moved a little and the white pat- tern are alternately displayed. It is diffi- cult to see the after image on all colors. Once it has been corrected it will not be visible in any color.
ghost images from the screen. Use spar- ingly. Watch the TV normally for a while before using this feature to see if the ghost image disappears on its own.

G An excessive ghosted image may be impossible to
clear entirely with White Wash. To return to nor- mal viewing, press the any button.


Displays a slide show to explain the various features of this TV. This feature is disabled in “Initial Setting-Home Use”.
Return to TV viewing.
After a while, Demo Mode starts. If you want to stop the demo, press any button. (except VOL or MUTE)
6 Show the difference XD Engine features.

AUTO VOLUME LEVELER (AUTO VOLUME)

Auto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program.
Because each broadcasting station has its own signal conditions, volume adjustment may be needed every time the channel is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each program.
Select AUDIO.
Select Auto Volume.
Select On or Off.


By differentiating the human sound range from others, it improves the sound quality of voices.
Adjustment for Clear Voice II Level With selecting On
Select Level. 4
Make appropriate adjustments. 5
Level 0 - +
E
Close

Sound Mode lets you enjoy the best sound without any special adjustment as the TV sets the appropriate sound options based on the program content. Standard, Music, Cinema, Sport, and Game are preset for optimum sound quality at the factory and are not adjustable.
Q.Menu
16:9
Cinema
Game Sport
CH
SOUND & LANGUAGE CONTROL
1Q. MENU Select Sound Mode.
2 Select Standard, Music, Cinema, Sport, or Game.
the AUDIO menu.
sound.
3Q. MENU Return to TV viewing.
to music.
movies.
events.
games.


Adjust the sound to suit your taste and room situations.
SRS TRUSURROUND XT Select this option to sound realistic.

Select AUDIO.
patented SRS technology that solves the prob- lem of playing 5.1 multichannel content over two speakers.
Select SRS TruSurround XT.
Select On or Off.


Adjust the left/right sound of speaker to suit your taste and room situations.
Select AUDIO.
Select Balance.
Make appropriate adjustments.


Turn the TV speakers off if using external audio equipment. If you wish to use an external Hi-Fi system or a SRS system, turn off the TV’s internal speakers.
Select AUDIO.
Select TV Speaker.
Select On or Off.


Settings of the selected Sound Mode return to the default factory settings.
Select AUDIO.
Select Reset.

STEREO/SAP BROADCAST SETUP
For Analog only: This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accom- panies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used if the broadcast is only in Mono.
Q.Menu
16:9
SOUND & LANGUAGE CONTROL
Analog TV Digital TV
1 Q. MENU
1 Q. MENU
Select SAP.
Select Multi Audio.
Select Mono, Stereo, or SAP.
Select other languages.
Return to TV viewing.
Return to TV viewing.


Other languages may be available if a digital signal is provided by the broadcasting station. This feature operates only in DTV/CADTV mode.



The menus can be shown on the screen in the selected language.
Select OPTION.
Select Menu Language(Language).
Select your desired language. From this point on, the on-screen menus will be shown in the selected language.


Captions are provided to help people with hearing loss watch TV. Select a caption mode for displaying cap- tioning information if provided on a program. Analog caption displays information at any position on the screen and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable. This TV is programmed to memorize the caption/text mode which was last set when you turned the power off. This function is only available when Caption Mode is set On.

The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the pro- gram provided for the hearing impaired.
The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provid- ed by the broadcaster. 5


Choose the language you want the DTV/CADTV Captions to appear in. Other Languages can be chosen for digital sources only if they are included on the program. This function in only available when Caption Mode is set On.
Select OPTION.
Select Caption.
Select On.


Customize the DTV/CADTV captions that appear on your screen. This function in only available when Caption Mode is turned On.
Customize the Style, Font, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language.


The time is set automatically from a digital channel signal. The digital channel signal includes information for the current time provided by the broadcasting station. Set the clock manually if the current time is set incorrectly by the auto clock function.

Select Auto, On, or Off (depending on whether or not your viewing area observes Daylight Saving time).


If the current time setting is wrong, set the clock manually.
Select the Year, Month, Date, Hour, or Minutes option. 4
G If you unplug the TV once or turn the

AUTO ON/OFF TIME SETTING

This function operates only if the current time has been set. The Off Time function overrides the On Time function if they are both set to the same time. The TV must be in standby mode for the On Time to work. If you do not press any button within 2 hours after the TV turns on with the On Time function, the TV will automatically revert to standby mode.
Select Off, Once, Daily, Mon.~Fri., Mon.~Sat., Weekend, or Sunday. 4

The Sleep Time turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off.
Q.Menu
16:9
Select Sleep Timer. 1 Q. MENU
TIME SETTING
2 Select Off, 10, 20, 30, 60, 90, 120, 180, or 240 minutes. 3Q. MENU Return to TV viewing.
the TIME menu.

Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broad- casting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be done : 1. Set ratings and categories to be blocked. 2. Specify a password 3. Enable the lock
V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to- video movies use the Movie Rating System (MPAA) only.

Set up blocking schemes to block specific channels, ratings, and external viewing sources. A password is required to gain access to this menu.



ENTER ■When you select On, the Lock System



Choose any 4 digits for your new password. As soon as the 4 digits are entered, re-enter the same 4 digits on the Confirm.


Blocks any channels that you do not want to watch or that you do not want your children to watch.
Input Block Ch.Change Move Page CH Move Previous Block/Unblock

Select a channel to block or unblock. 4


Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.

Select G, PG, PG-13, R, NC-17, X, or Blocking Off. 4
be available, PG-13, R, NC-17 and X will be blocked.


Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audi- ences in the TV Rating - sub menu, your children can view those programs.

Select TV Rating-Children.


Based on the ratings, blocks certain TV programs that you and your family do not want to view.



Select E, C, C8+, G, PG, 14+, 18+, or Blocking Off. 4


Select E, G, 8ans+, 13ans+, 16ans+, 18ans+, or Blocking off. 4


This function is available only for digital channels. This function operates only when TV has received Region5 Rating data.
(On Screen Display) may differ slightly from what is shown in this manual.

Select desired option and block it. 5




The TV can be set up so that it can only be used with the remote control. This feature can be used to prevent unauthorized viewing by locking out the front panel controls. This TV is programmed to remember which option it was last set to even if you turn the TV off.
Select OPTION.
Select Key Lock.

off, press the INPUT, CH D , E button on the TV or POWER, INPUT, CH , or NUMBER buttons on the remote con- trol.
‘ Key Lock’ appears on the screen if any button(Except (power) button) on the front panel is pressed while view- ing the TV.

TROUBLESHOOTING
The operation does not work normally.
causing obstruction. Ensure you are pointing the remote control directly at the TV.
*This feature is not available for all models.
The video function does not work.
No picture &No sound
where the product’s power cord was plugged in.
contact your service center, if the picture has not appeared after five minutes.
No or poor color
No picture when connecting HDMI
The HDMI cables don’t support HDMI version 1.3, it cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.

The audio function does not work.
Picture OK & No sound
No output from one
when the product is turned on or off and does not indicate a fault with the product.
No sound when connecting
There is a problem in PC mode. (Only PC mode applied)
The signal is out of range
Vertical bar or stripe on
background & Horizontal Noise &
Screen color is unstable

MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
G If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.

50PQ20, 50PQ10 (50PQ20-UA, 50PQ10-UB)
40.5 x 28.3 x 12.1 inches 1031.2 x 720.9 x 308.0 mm 40.5 x 25.8 x 3.1 inches 1031.2 x 656.7 x 80.8 mm
47.9 x 32.2 x 13.8 inches 1216.7 x 818.1 x 353.0 mm 47.9 x 29.8 x 3.2 inches 1216.7 x 759.0 x 83.0 mm
Dimensions (Width x Height x Depth)
With stand Without stand
54.6 lbs / 24.8 kg 50.0 lbs / 22.7 kg
74.2 lbs / 33.7 kg 68.7 lbs / 31.2 kg
50PQ30, 50PQ31, 50PQ30C (50PQ30-UA, 50PQ30-UD, 50PQ31-UD,
MODELS
50PQ30C-UA)
42PQ30C-UA )
40.5 x 28.3 x 12.1 inches 1031.2 x 720.9 x 308.0 mm
47.9 x 32.2 x 13.8 inches 1216.7 x 818.1 x 353.0 mm
Dimensions (Width x Height x Depth)
40.5 x 25.8 x 3.1 inches 1031.2 x 656.7 x 80.8 mm
47.9 x 29.8 x 3.2 inches 1216.7 x 759.0 x 83.0 mm
With stand Without stand
54.6 lbs / 24.8 kg 50.0 lbs / 22.7 kg
74.2 lbs / 33.7 kg 68.7 lbs / 31.2 kg
50PQ60 (50PQ60-UA)
60PS10 (60PS10-UA)
40.9 x 28.5 x 12.1 inches 1040.8 x 725.8 x 308.0 mm
48.3 x 32.4 x 13.8 inches 1228.8 x 824.6 x 353.0 mm
57.7 x 39.7 x 16.2 inches 1468.0 x 1009.1 x 413.9 mm 57.7 x 37.3 x 3.4 inches 1468.0 x 949.5 x 88.5 mm
Dimensions (Width x Height x Depth)
40.9 x 26.3 x 3.0 inches 1040.8 x 669.2 x 76.8 mm
48.3 x 30.3x 3.1 inches 1228.8 x 772.0 x 78.9 mm
With stand Without stand
55.7 lbs / 25.3 kg 51.3 lbs / 23.3 kg
77.1 lbs / 35.0 kg 71.6 lbs / 32.5 kg
177.6 lbs/ 80.6 kg 160.0 lbs/ 72.6 kg
50PS60, 50PS60C (50PS60-UA, 50PS60C-UA)
60PS60, 60PS60C (60PS60-UA, 60PS60C-UA)
Dimensions (Width x Height x Depth)
47.9 x 32.2 x 13.8 inches 1216.7 x 818.1 x 353.0 mm
48.3 x 32.4 x 13.8 inches 1228.8 x 824.6 x 353.0 mm
57.6 x 38.6 x 15.5 inches 1465.4 x 982.6 x 395.5mm
47.9 x 29.8 x 3.2 inches 1216.7 x 759.0 x 83.0 mm
48.3 x 30.3 x 3.1 inches 1228.8 x 772.0 x 78.9 mm
57.6 x 35.5 x 3.2 inches 1465.4 x 903.2 x 82.1 mm
78.0 lbs / 35.4 kg 72.3 lbs / 32.8 kg
80.0 lbs / 36.3 kg 74.5 lbs / 33.8 kg
111.9 lbs / 50.8 kg 99.2 lbs / 45.0 kg
With stand Without stand
Power requirement Television System Program Coverage External Antenna Impedance
AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
Operating Temperature Operating Humidity
32 ~ 104°F (0 ~ 40°C) Less than 80%
Storage Temperature Storage Humidity

PROGRAMMING THE REMOTE CONTROL (This feature is not available for all models.)
The provided universal remote control can be programmed to operate most remote-controllable devices. Note that the remote may not control all models of other brands.
Testing your remote control. To find out whether your remote control can operate other components without programming, turn on a component such as a STB and press the corresponding mode button (such as a STB) on the remote con- trol, while pointing at the component. Test the POWER and CH buttons to see if the component responds correctly. If the component does not operate correctly, the remote control requires programming to operate the device.
Turn on the component to be programmed, then press the corresponding mode button (such as STB) on the remote control. The remote control button of the desired device is illuminated.
Press the MENU and MUTE buttons simultaneously, and the remote control is ready to be programmed with the code.
Enter a code number using the number buttons on the remote control. Programming code numbers for the corresponding component can be found on the following pages. If the code is correct, the device will turn off.
Press the MENU button to store the code.
Test the remote control functions to see if the component responds correctly. If not, repeat from step 2.

VCR
Brand Codes Brand Codes Brand Codes
AIWA 034 AKAI 016 043 046 124 125 146 AMPRO 072 ANAM 031 033 103 AUDIO DYNAMICS 012 023 039 043 BROKSONIC 035 037 129 CANON 028 031 033 CAPEHART 108 CRAIG 003 040 135 CURTIS MATHES 031 033 041 DAEWOO 005 007 010 064 065 108 110 111 112 116 117 119 DAYTRON 108 DBX 012 023 039 043 DYNATECH 034 053 ELECTROHOME 059 EMERSON 006 017 025 027 029 031 034 035 036 037 046 101 129 131 138 153 FISHER 003 008 009 010 FUNAI 034 GE 031 033 063 072 107 109 144 147 GO VIDEO 132 136 HARMAN KARDON 012 045 HITACHI 004 018 026 034 043 063 137 150 INSTANTREPLAY 031 033 JCL 031 033 JCPENNY 012 013 015 033 040 066 101 JENSEN 043 JVC 012 031 033 043 048 050 055 060 130 150 152 KENWOOD 014 034 039 043 047 048 LG (GOLDSTAR) 001 012 013 020 101 106 114 123 LLOYD 034 LXI 003 009 013 014 017 034 101 106 MAGIN 040
MAGNAVOX 031 033 034 041 067 068 MARANTZ 012 031 033 067 069 MARTA 101 MATSUI 027 030 MEI 031 033 MEMOREX 003 010 014 031 033 034 053 072 101 102 134 139 MGA 045 046 059 MINOLTA 013 020 MITSUBISHI 013 020 045 046 049 051 059 061 151 MTC 034 040 MULTITECH 024 034 NEC 012 023 039 043 048 NORDMENDE 043 OPTONICA 053 054 PANASONIC 066 070 074 083 133 140 145
SAMSUNG 032 040 102 104 105 107 109 112 113 115 120 122 125 SANSUI 022 043 048 135 SANYO 003 007 010 014 102 134 SCOTT 017 037 112 129 131 SEARS 003 008 009 010 013 014 017 020 031 042 073 081 101 SHARP 031 054 149 SHINTOM 024 SONY 003 009 031 052 056 057 058 076 077 078 149 SOUNDESIGN 034 STS 013 SYLVANIA 031 033 034 059 067 SYMPHONIC 034 TANDY 010 034 TATUNG 039 043 TEAC 034 039 043 TECHNICS 031 033 070 TEKNIKA 019 031 033 034 101 THOMAS 034 TMK 006 TOSHIBA 008 013 042 047 059 082 112 131 TOTEVISION 040 101 UNITECH 040 VECTOR RESEARCH 012 VICTOR 048 VIDEO CONCEPTS 012 034 046 VIDEOSONIC 040 WARDS 003 013 017 024 031 033 034 040 053 054 131 YAMAHA 012 034 039 043 ZENITH 034 048 056 058 072 080 101
PENTAX 013 020 031 033 063 PHILCO 031 034 067 PHILIPS 031 033 034 054 067 071 101 PILOT 101 PIONEER 013 021 048 PORTLAND 108 PULSAR 072 QUARTZ 011 014 QUASAR 033 066 075 145 RCA 013 020 033 034 040 041 062 063 107 109 140 144 145 147 REALISTIC 003 008 010 014 031 033 034 040 053 054 101 RICO 058 RUNCO 148 SALORA 014

HDSTB
Brand Codes Brand Codes Brand Codes
ALPHASTAR DSR 123 AMPLICA 050 BIRDVIEW 051 126 129 CHANNEL MASTER 013 014 015 018 036 055 CHAPARRAL 008 009 012 077 CITOH 054 CURTIS MATHES 050 145 DRAKE 005 006 007 010 011 052 112 116 141 DX ANTENNA 024 046 056 076 ECHOSTAR 038 040 057 058 093 094 095 096 097 098 099 100 122 ELECTRO HOME 089 EUROPLUS 114 FUJITSU 017 021 022 027 133 134 GENERAL INSTRUMENT 003 004 016 029 031 059 101 HITACHI 139 140
PROSAT 072 RCA 066 106 REALISTIC 043 074 SAMSUNG 123 SATELLITE SERVICE CO 028 035 047 057
057 104 HUGHES 068 JANIEL 060 147 JERROLD 061 KATHREIN 108 LEGEND 057 LG 001 LUTRON 132 LUXOR 062 144 MACOM 010 059 063 064 065 MEMOREX 057 NEXTWAVE 028 124 125 NORSAT 069 070 PACE SKY SATELLITE 143 PANASONIC 060 142 PANSAT 121 PERSONAL CABLE 117 PHILIPS 071 PICO 105 PRESIDENT 019 102 PRIMESTAR 030 110 111
085 SCIENTIFIC ATLANTA 032 138 SONY 103 STARCAST 041 SUPER GUIDE 020 124 125 TEECOM 023 026 075 087 088 090 107 130 137 TOSHIBA 002 127 UNIDEN 016 025 042 043 044 045 048 049 078 079 080 086 101 135 136 VIEWSTAR 115 WINEGARD 128 146 ZENITH 081 082 083 084 091 120
DVD
Brand Codes Brand Codes Brand Codes
APEX DIGITAL 022 DENON 020 014 GE 005 006 HARMAN KARDON 027 JVC 012 LG 001 010 016 025 MAGNAVOX 013 MARANTZ 024
MITSUBISHI 002 NAD 023 ONKYO 008 017 PANASONIC 003 009 PHILIPS 013 PIONEER 004 026 PROCEED 021 PROSCAN 005 006
RCA 005 006 SAMSUNG 011 015 SONY 007 THOMPSON 005 006 TOSHIBA 019 008 YAMAHA 009 018 ZENITH 010 016 025

1. How to Connect
Single pulse, modulated with 37.917KHz signal at 455KHz
FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3
Lead code Low custom code High custom code Data code Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
4.5 ms 9 ms
0.55 ms
2.25 ms 9 ms
Bit ”0” Bit ”1”
0.56 ms
0.56 ms
1.12 ms
2.24 ms
The waveform is transmitted as long as a key is depressed.

Code Function Note (Hexa)
Code Function Note (Hexa)
08 POWER Remote control Button (Power On/Off)
D6 TV Discrete IR Code
45 Q.MENU Remote control Button
43 MENU Remote control Button
C4 POWER ON Discrete IR Code
0B INPUT Remote control Button
10-19 Number Key 0-9 Remote control Button
C5 POWER OFF Discrete IR Code
4C - Dash(List) Remote control Button
1A FLASHBK Remote control Button
5A AV1 Discrete IR Code
09 MUTE Remote control Button
02 VOL + Remote control Button
D0 AV2 Discrete IR Code
03 VOL - Remote control Button
00 CH Remote control Button
BF COMPONENT1 Discrete IR Code
01 CH Remote control Button
1E FAV Remote control Button
D4 COMPONENT2 Discrete IR Code
40 Remote control Button
41 Remote control Button
D5 RGB-PC Discrete IR Code
07 Remote control Button
06 Remote control Button
CE HDMI1 Discrete IR Code
44 ENTER Remote control Button
28 RETURN Remote control Button
CC HDMI2 Discrete IR Code
7E SIMPLINK Remote control Button
30 AV MODE Remote control Button
E9 HDMI3 Discrete IR Code
79 RATIO Remote control Button
65 FREEZE Remote control Button
DA HDMI4 Discrete IR Code
95 ENERGY Remote control Button
AA Info Remote control Button
76 Ratio 4:3 Discrete IR Code
72 Red Remote control Button
(Only 4:3 Mode)
71 Green(Stop A ) Remote control Button
77 Ratio 16:9 Discrete IR Code
63 Yellow(Play G) Remote control Button
(Only 16:9 Mode)
61 Blue(Pause l l) Remote control Button
AF Ratio Zoom Discrete IR Code
8E FF GG Remote control Button
8F Rew FF Remote control Button
Only 42/50PQ60, 50/60PS60, 50/60PS60C

The RS-232C port allows you connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the TV’s functions externally.

The instructions below are provided to help with programming software or to test functionality using telenet software.
Type of Connector; D-Sub 9-Pin Male
Communication Parameters


RS-232C Configurations
Either cable below can be used.
7-Wire Configuration (Serial female-female NULL modem cable)
3-Wire Configurations (Not standard)
PC TV

RXD 2 3 TXD TXD 3 2 RXD GND 5 5 GND DTR 4 6 DSR DSR 6 4 DTR RTS 7 8 CTS CTS 8 7 RTS
RXD 2 3 TXD TXD 3 2 RXD GND 5 5 GND DTR 4 6 DTR DSR 6 4 DSR RTS 7 7 RTS CTS 8 8 CTS
Use this function to specify a TV ID number. Refer to ‘Real Data Mapping’.
Select OPTION.

Select Set ID.
Choose the desired TV ID number. The adjustment range of Set ID is 1~99.

DATA (Hexadecimal) COMMAND1 COMMAND2 DATA (Hexadecimal)
01. Power k a 00 ~ 01 02. Input Select x b (G p.112) 03. Aspect Ratio k c (G p.112) 04. Screen Mute k d 00 ~ 01 05. Volume Mute k e 00 ~ 01 06. Volume Control k f 00 ~ 64 07. Contrast k g 00 ~ 64 08. Brightness k h 00 ~ 64 09. Color k i 00 ~ 64 10. Tint k j 00 ~ 64 11. Sharpness k k 00 ~ 64 12. OSD Select k l 00 ~ 01
00 ~ 01 k m 13. Remote Control Lock Mode 14. Treble k r 00 ~ 64 15. Bass k s 00 ~ 64 16. Balance k t 00 ~ 64 17. Color Temperature k u 00 ~ 02 18. ISM Method j p (G p.113) 19. Power Saving j q 00 ~ 01 20. Auto Configuration j u (G p.113) 22. Channel Add/Del m b 00 ~ 01 23. Key m c (G p.114)
COMMAND1 COMMAND2 DATA00 (Hexadecimal)
physical major major low minor high minor low attribute program high program low m a
* In this model, TV will not send the status during the standby mode. * Data Format [Command 2] : Use as command. [Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’. [DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’. [OK] : Use the large character.
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the set.(j, k, m or x) [Command 2] : Second command to control the set. [Set ID] : You can adjust the set ID to choose desired TV ID
number in Setup menu. Adjustment range is 1~ 99. When selecting Set ID ‘0’, every connected the TV is controlled. Set ID is indicated as decimal (1~ 99) on menu and as Hexa decimal (0x0~ 0x63) on transmission /receiving protocol. [DATA] : To transmit the command data.
[Command2][ ][Set ID][ ][NG][Data][x]
The TV transmits ACK (acknowledgement) based on this for- mat when receiving abnormal data from non-viable functions or communication errors.
Transmit the ‘FF’ data to read status of command. [Cr] : Carriage Return
ASCII code ‘0x0D’ [ ] : ASCII code ‘space (0x20)’ * In this model, TV will not send the status during the standby mode.
Data3: Wait more time * In this model, TV will not send the status during the standby mode. * Data Format [Command 2] : Use as command. [Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’. [DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’. [NG] : Use the large character
[Command2][ ][Set ID][ ][OK][Data][x]
The TV transmits ACK (acknowledgement) based on this for- mat when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.

Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]
To control Power On/Off of the TV.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
To adjust volume.
You can also adjust volume with the volume buttons on remote control.
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
* In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
*Refer to ‘Real data mapping’. G p.110.
* Note: In this model, TV will send the Acknowledge after power on processing completion.
Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
There might be a time delay between command and acknowledge.
To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
To select input source for TV.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
*Refer to ‘Real data mapping’. G p.110.
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
*Refer to ‘Real data mapping’. G p.110.
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
To adjust the screen format.
To adjust screen color.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
You can also adjust color in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
*Refer to ‘Real data mapping’. G p.110.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
To select screen mute on/off.
To adjust screen tint.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
*Refer to ‘Real data mapping’. G p.110.
Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [ j ][ ][Set ID][ ][OK/NG][Data][x]
* In case of Video-Out mute on only, TV will display On Screen Display(OSD). But, In case of Screen Mute On, TV will not display OSD.
To adjust screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control.
*Refer to ‘Real data mapping’. G p.110.
Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][e][ ][Set ID][ ][Data][Cr]

To select OSD (On Screen Display) on/off.
To avoid having a fixed image remain on screen.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Transmission [ j ][p][ ][Set ID][ ][Data][Cr]
Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [p][ ][Set ID][ ][OK/NG][Data][x]
To lock the remote control and the front panel controls on the TV.
To control the low power function on/off.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Transmission [ j ][q][ ][Set ID][ ][Data][Cr]
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
If you’re not using the remote control and front panel controls on the TV, use this mode. When main power is on/off, remote control lock is released.
To adjust treble.
Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]
You can also adjust treble in the AUDIO menu.
Transmission [k][r][ ][Set ID][ ][Data][Cr]
To adjust picture position and minimize image shaking automatically. Auto configuration only works in RGB-PC mode.
*Refer to ‘Real data mapping’. G p.110.
Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]
Transmission [ j ][u][ ][Set ID][ ][Data][Cr]
To adjust bass.
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
You can also adjust bass in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
To tune channel to following physical/major/minor number.
*Refer to ‘Real data mapping’. G p.110.
Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]
Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the number that the channel should be mapped to, and the Minor is the sub-channel. Since the ATSC tuner automatically maps the channel to the Major number, the Physical number is not required when sending a command.
To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
*Refer to ‘Real data mapping’. G p.110.
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]
To adjust color temperature.
You can also adjust color temperature in the PICTURE menu.
Transmission [k][u][ ][Set ID][ ][Data][Cr]
Two bytes are available for the Major and Minor, nor- mally only the second byte is used.
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
Not needed for NTSC.

Data 05:
Two/One Part Channel 7
Using Physical Channel 6
NTSC Air NTSC Cable
ATSC Air ATSC Cable_std ATSC Cable_hrc
ATSC Cable_irc ATSC cable_auto
... Reserved
The table above lists the binary code which must be converted to Hexadecimal before sending. For example: The binary code to tune the sub source to an NTSC cable channel is “1000 0001”, which translates to “81” in Hex.
To add and delete the channels.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
* 7th bit : For which source do you want to change the channel.
* 6th bit: Use a two part or one part channel. Most cases just use 0 since it’s ignored when using NTSC.
To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
* 5th bit: Use 0 with NTSC since it can only use the phys- ical channel number. Normally use 1 for ATSC since most times it doesn’t matter what the physical number is.
G p.108.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
* 4th bit: Set to 0.
* 3-0 bits: Choose signal type.
* Tune Command Examples:
Acknowledgement[a][ ][Set ID][ ][OK][Data00][Data01] [Data02][Data03][Data04][x][a][ ][Set ID]


Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.