
LCD TV PLASMA TV OWNER’S MANUAL
LCD TV MODELS 32LG6*** 37LG6*** 42LG6*** 47LG6*** 42LG7*** 47LG7*** 52LG7*** 32LG8*** 42LG8***
PLASMA TV MODELS 50PG3*** 42PG6*** 50PG6*** 60PG6*** 50PG7*** 60PG7***
Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. Refer to the label on the back cover and quote this information. To your dealer when requiring service.



Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the product.
I Image shown may differ from your TV.

Polishing Cloth Polishing cloth for use on the screen This feature is not available for all models.
*Lightly wipe any stains or fingerprints on the surface of the TV with the polishing cloth.
Do not use excessive force. This may cause scratching or discolouration.
Ferrite core can be used to reduce the electromagnetic wave when connecting the power cord. The closer the location of the ferrite core to the power plug, the better it is.



FRONT PANEL CONTROLS
I This is a simplified representation of the front panel. Image shown may differ from your TV. I If your product has a protection film attached, remove the film and then wipe the product with a polishing
cloth.
Plasma TV Models

This feature is not available for all models. After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.



Intelligent Sensor Adjusts picture according to the surrounding conditions
Intelligent Sensor Adjusts picture according to the surrounding conditions.




I This is a simplified representation of the back panel. Image shown may differ from your TV.
HDMI Input Connect a HDMI signal to HDMI IN.
S-Video Input Connect S-Video out from an S-VIDEO device.
Audio/Video Input Connect audio/video output from an external device to these jacks.
L/L/MONO MONO R AUDIO AUDIO VIDEO VIDEO
HDMI Input Connect a HDMI signal to HDMI IN. Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable.
Component Input Connect a component video/audio device to these jacks.
Antenna Input Connect RF antenna to this jack.
RGB/Audio Input Connect the monitor output from a PC to the appropriate input port.
Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
Audio/Video Input (AV IN 1) Connect audio/video output from an external device to these jacks.
RS-232C Input (CONTROL) Port Connect the serial port of the control devices to the RS-232C jack. (This feature is not available for all models.)
AV Output Connect second TV or monitor to the AV OUT socket on the TV. Variable Audio Output Connect an external amplifier or add a subwoofer to your surround sound system.


HDMI Input Connect a HDMI signal to HDMI IN.
S-Video Input Connect S-Video out from an S-VIDEO device.
Audio/Video Input Connect audio/video output from an external device to these jacks.
S-Video Input Connect S-Video out from an S-VIDEO device.
Audio/Video Input Connect audio/video output from an external device to these jacks.
L(L(MONO) MONO) R AUDIO AUDIO VIDEO VIDEO

HDMI Input Connect a HDMI signal to HDMI IN. Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable. (HDMI IN 3 is available for 42/47LG6***, 42/47/52LG7***)
Component Input Connect a component video/audio device to these jacks.
Antenna Input Connect RF antenna to this jack.
RGB/Audio Input Connect the monitor output from a PC to the appropriate input port.
Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
Audio/Video Input Connect audio/video output from an external device to these jacks.
AV Output Connect second TV or monitor to the AV OUT socket on the TV. Variable Audio Output Connect an external amplifier or add a subwoofer to your surround sound system.

The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw.
G To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.

STAND INSTALLATION
I Image shown may differ from your TV.
When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt.

Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Fix the 4 bolts securely using the holes in the back of the TV.
When installing the wall-mounted unit, use the protection cover for desk-type stand installation. Insert the PROTECTION COVER into the TV until clicking sound.

Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the TV as shown.


2 Assemble the parts of the Stand Body with Cover Base of the TV.

Fix the 4 bolts securely using the holes in the back of the TV.



Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Fix the 4 bolts securely using the holes in the back of the TV.
2 Assemble the parts of the Stand Body with the Cover Base of the TV.
When installing the wall-mounted unit, use the protection cover for desk-type stand installation.
After removing the protection paper from the protection cover, adhere it to the TV as shown.
Insert the PROTECTION COVER into the TV until clicking sound.


To connect additional equipment, see the External Equipment Setup section.
To connect additional equipment, see the External Equipment Setup section.
Fix the Cable Holder as shown and bundle the cables.
Hold the CABLE MANAGEMENT CLIP with both hands and pull it upward.
Separate CABLE MAN- AGEMENT from TV by pressing two latches.
* For the 42PG6*** model, press the center of the CABLE MANAGEMENT CLIP and then lift up it.
G Do not use the CABLE MANAGEMENT CLIP to lift the TV. - If the TV is dropped, you may be injured or the TV may be damaged.

I Image shown may differ from your TV.

Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT CLIP as shown. If your TV has the CABLE HOLDER, install it as shown and bundle the cables.
Hold the CABLE MANAGEMENT CLIP with both hands and pull it upward.
G Do not use the CABLE MANAGEMENT CLIP to lift the TV. - If the TV is dropped, you may be injured or the TV may be damaged.


Align the hole with the tab on the CABLE MANAGEMENT CLIP. Turn the CABLE MANAGEMENT CLIP as shown. Note: This cable management can be broken by excessive pressure.
Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section of the manual. 1
Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section.

PLEASE SET IT UP CAREFULLY SO THE PRODUCT DOES NOT FALL OVER.
A You should purchase necessary components to fix the TV to the wall on the market.
A Position the TV close to the wall to avoid the possibility of it falling when pushed.
A The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the
possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.

Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen then bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with bolts to the wall. Ensure that both brackets are even.

3 Use a strong cord to secure the TV. Secure the cord in such a way that it becomes taught when the TV is in position.

G When moving the TV undo the cords first.
G Use a platform or cabinet string and large enough to support the size and weight of the TV.
G To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.

I The TV can be installed in various ways such as on a wall, or on a desktop etc.
I The TV is designed to be mounted horizontally.

EARTHING Ensure that you connect the earth wire to prevent possi- ble electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.
DESKTOP PEDESTAL INSTALLATION
For adequate ventilation allow a clearance of 4” (10cm) all around the TV .


For adequate ventilation allow a clearance of 4” (10cm) all around the TV. We recommend that you use a wall mounting bracket of LG brand when mounting the TV to a wall.
Power Supply · Circuit breaker

I To prevent damage do not connect to the mains outlet until all connections are made between the devices.

I An antenna cable and converter are not supplied.
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
I In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the
antenna as shown above.
I If signal needs to be split for two TVs, use an antenna signal splitter for connection.

I To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.
I This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 42/50/60PG6*** models.
I Image shown may differ from your TV.
Connecting with a component cable


Connect the video outputs (Y, PB, PR) of the digital TV top box to the COMPONENT IN VIDEO jacks on the TV.
Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO jacks on the TV.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
Select Component1 input source using the INPUT button on the remote control. If connected to COMPONENT IN 2, select Component2 input source.


Connecting a set-top box with an HDMI cable
HDMI IN HDMI DVI IN HDMI IN HDMI IN HDMI/DVI IN HDMI/DVI IN
Connect the HDMI output of the digital set-top box to the HDMI/DVI IN 1, HDMI IN 2 or HDMI IN 3(except 32/37LG6***, 32/42LG8***) jack on the TV.
EXTERNAL EQUIPMENT SETUP
L/MONO R AUDIO AV
VIDEO
OUT
Select HDMI1/DVI, HDMI2 or HDMI3(except 32/37LG6***, 32/42LG8***) input source using the INPUT button on the remote control.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
G TV can receive the video and audio signal simultaneously with using a HDMI cable.
G If the digital set-top box supports Auto HDMI function, the output resolution of the source device will
be automatically TV to 1280x720p.
G If the digital set-top box player does not support Auto HDMI, you need to TV the output resolution
appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p. (42/47LG6***, 42/47/52LG7***, 50PG3***, 50/60PG7***, 32/42LG80F* : 1920x1080i/1080p)


HDMI IN HDMI DVI IN HDMI/DVI IN HDMI/DVI IN
Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1 jack on the TV.
Connect the audio output of the digital set-top box to the AUDIO(RGB/DVI) jack on the TV.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
Select HDMI1/DVI input source using the INPUT button on the remote control.

G HDMI2, HDMI3(except 32/37LG6***, 32/42LG8***) source does not support DVI source.
G If the set-top box has a DVI output and no HDMI output, a separated audio connection is necessary.
G If the set-top box does not support Auto DVI, you need to set the output resolution appropriately.

DVD SETUP
Connecting with a component cable

Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the TV.
Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the TV.
Select Component1 input source using the INPUT button on the remote control. If connected to COMPONENT IN 2, select Component 2 input source.
Refer to the DVD player's manual for operating instructions.
Component Input ports To achieve better picture quality, connect a DVD player to the component input ports as shown below.



Connect the S-VIDEO output of the DVD to the S-VIDEO input on the TV.
Connect the audio outputs of the DVD to the AUDIO input jacks on the TV.
Select AV2 input source using the INPUT button on the remote control.
Refer to the DVD player's manual for operating instructions.

Connecting with a HDMI cable
Connect the HDMI output of the DVD to the HDMI/DVI IN 1, HDMI IN 2 or HDMI IN 3(except 32/37LG6***, 32/42LG8***) jack on the TV.
HDMI IN HDMI DVI IN HDMI IN HDMI IN HDMI/DVI IN HDMI/DVI IN
IN 1
Select HDMI1/DVI, HDMI2 or HDMI3(except 32/37LG6***, 32/42LG8***) input source using the INPUT button on the remote control.
VIDEO
OUT
VARIABLE AUDIO OUT
Refer to the DVD player's manual for operating instructions.
G The TV can receive video and audio signals simultaneously when
using a HDMI cable.
G If the DVD player supports Auto HDMI function, the output resolu-
tion of the source device will be automatically TV to 1280x720p.
G If the DVD player does not support Auto HDMI, you must TV the
output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p. (42/47LG6***, 42/47/52LG7***, 50PG3***, 50/60PG7***, 32/42LG80F* : 1920x1080i/1080p)

I To avoid picture noise (interference), allow adequate distance between the VCR and TV.
I Typically a frozen still picture from a VCR. If 4:3 picture format is used for an extended period the fixed
images on the sides of the screen may remain visible.


Connect the ANT OUT socket of the VCR to the ANTENNA IN socket on the TV.
Connect the antenna cable to the ANT IN socket of the VCR.
Press the PLAY button on the VCR and match the appropriate programme between the TV and VCR for viewing.



Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colours (Video = yellow, Audio Left = white, and Audio Right = red)
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
Select AV1 input source using the INPUT button on the remote control. If connected to AV IN 2, select AV2 input source.

G If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack


Connect the S-VIDEO output of the VCR to the S-VIDEO input on the TV. The picture quality is improved; compared to normal composite (RCA cable) input.
Connect the audio outputs of the VCR to the AUDIO input jacks on the TV.
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
Select AV2 input source using the INPUT button on the remote control.

G If both S-VIDEO and VIDEO sockets have been connected
to the S-VHS VCR simultaneously, only the S-VIDEO can be received.

OTHER A/V SOURCE SETUP


Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colours. (Video = yellow, Audio Left = white, and Audio Right = red)
Select AV2 input source using the INPUT button on the remote control. If connected to AV IN 1, select AV1 input source.
Operate the corresponding external equipment. Refer to external equipment operating guide.

Use to connected either an external amplifier, or add a sub-woofer to your surround sound system.
VIDEO
OUT
VARIABLE AUDIO OUT
Connect the input jack of the stereo amplifier to the VARIABLE AUDIO OUT jacks on the TV.
Set up your speakers through your analog stereo amplifier, according to the instructions provided with the amplifier. 2
NOTE !
G When connecting with external audio equipments, such as
amplifiers or speakers, please turn the TV speakers off. (G p.86)
G Select Variable Out in Audio menu to connect the
VARIABLE AUDIO OUT jacks.(G p.87)

AV OUTPUT SETUP

The TV has a special signal output capability which allows you
to hook up the second TV or monitor.

Connect the second TV or monitor to the TV’s AV OUT jacks.
See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings.

G Component, RGB, HDMI input sources cannot be used for
G We recommend to use the AV OUT jacks for VCR recording.

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.


Connect the RGB output of the PC to the RGB(PC) jack on the TV.
Connect the PC audio output to the AUDIO(RGB/DVI) jack on the TV.
Select RGB PC input source using the INPUT button on the remote control.

G To enjoy vivid picture and sound, connect the PC
G The synchronization input waveform for
to the TV.
Horizontal and Vertical frequencies are separate.
G Avoid keeping a fixed image on the TV ’s screen
G If the resolution of PC is over SXGA, there will
for prolonged periods of time.The fixed image may become permanently imprinted on the screen;use a screen saver when possible.
be no picture on the TV.(only HD Models)
G Connect the audio cable from the PC to the
Audio input on the TV.(Audio cables are not included with the TV).
G Connect the PC to the RGB (PC) port of the TV;
change the resolution output of PC accordingly.
G If you use too long an RGB-PC cable, there may
G There may be interference relating to resolution,
be interference on the screen. We recommend using under 5m of the cable. This provides the best picture quality.
vertical pattern, contrast or brightness in PC mode. Change the PC mode to another resolu- tion or change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the man- ufacturer of the PC graphic card.

Plasma TV models
Horizontal Vertical Frequency(kHz) Frequency(Hz)
Horizontal Vertical Frequency(kHz) Frequency(Hz)
31.47 59.94 31.50 60.00
640x350 720x400 640x480 800x600 1024x768 1280x768 1360x768 1366x768 1280x1024 1920x1080
31.468 70.09 31.469 70.09 31.469 59.94 37.879 60.317 48.363 60.004 47.776 59.87 47.720 59.799 47.7 60 63.668 59.895 66.587 59.934
31.25 50.00
44.96 59.94 45.00 60.00 37.50 50.00
33.72 59.94 33.75 60.00 28.125 50.00
67.432 59.94 67.5 60 56.250 50 27 24 33.75 30
Only 50/60PG6*** Only 50/60PG7***, 50PG3***
Horizontal Vertical Frequency(kHz) Frequency(Hz)
Horizontal Vertical Frequency(kHz) Frequency(Hz)
31.47 59.94 31.50 60.00
640x350 720x400 640x480 800x600 1024x768 1280x768 1360x768 1366x768 1280x1024 1920x1080
31.468 70.09 31.469 70.09 31.469 59.94 37.879 60.317 48.363 60.004 47.776 59.87 47.720 59.799 47.7 60 63.668 59.895 66.587 59.934
31.25 50.00
44.96 59.94 45.00 60.00 37.50 50.00
33.72 59.94 33.75 60.00 28.125 50.00
67.432 59.94 67.5 60 56.250 50 27 24 33.75 30
Only 42/47LG6***, 42/47/52LG7***, 32/42LG80F*

Screen Setup for PC mode
Auto Configure (RGB [PC] mode only)
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment.
This function is for automatic adjustment of the screen position, clock, and phase. The displayed image will be unstable for a few seconds while the auto configuration is in progress.
Picture Mode Colour Temperature
Press the MENU button and then use / button to select the Picture menu.
Advanced Aspect Ratio Picture Reset Screen
Press the button and then use / button to select Screen.
Press the button and then use / button to select Auto Config..
Picture Mode Colour Temperature
Advanced Aspect Ratio Picture Reset Screen To Set Screen G
Press the button to start Auto Config..
Auto config. Manual Config. XGA Mode Reset
To Set Auto Config. G
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

Manual Config. (RGB [PC] mode only) - Adjustment for screen Phase, Clock, Position
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually.
It’s not available to use Phase, Clock function in COMPONENT (480i/480p/576i/576p/720p/1080i/1080p), HDMI (480p/576p/720p/1080i/1080p).
Clock This function is to minimize any vertical bars or stripes
visible on the screen background the horizontal screen size will also change.
Phase This function allows you to remove any horizontal noise
and clear or sharpen the image of characters.
Picture Mode Colour Temperature
Advanced Aspect Ratio Picture Reset Screen
Press the MENU button and then use / button to select the Picture menu.
Press the button and then use / button to select Screen.
Picture Mode Colour Temperature
Advanced Aspect Ratio Picture Reset Screen To Set Screen G
Press the button and then use / button to select Manual Config..
Press the button and then use / button to select Phase, Clock, H-Position or V-Position.
Auto config. Manual Config. XGA Mode Reset
Manual Config. G
Phase 51 Clock 50 H-Position 50 V-Position 50
Press the / button to make appropriate adjustments.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Picture · Picture · Screen


To view a normal picture, match the resolution of RGB mode and selection of XGA mode.
This function works in the following mode: RGB[PC] mode.
Press the MENU button and then use / button to select the Picture menu.
Press the button and then use / button to select Screen.
Press the button and then use / button to select XGA Mode.
Advanced Aspect Ratio Picture Reset Screen To Set Screen G
Press the button and then use / button to select the desired XGA resolution.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.


This function operates in current mode. To initialize the adjusted value
Press the MENU button and then use / button to select the Picture menu.
Press the button and then use / button to select Screen.
Press the button and then use / button to select Reset.
Advanced Aspect Ratio Picture Reset Screen To Set Screen G
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Auto config. Manual Config. XGA Mode Reset Reset G

REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
Selects the remote operating modes.
Switches the TV on from standby or off to standby.
External input mode rotate in regular sequence. Switches the TV on from standby.
Q. MENU
Select the desired quick menu source.
Selects a menu. Clears all on-screen displays and returns to TV viewing from any menu.
See a list of AV devices connected to TV. When you toggle this button, the Simplink menu appears at the screen.
Allows the user to move return one step in an interac- tive application or other user interaction function.
Enter to the mode.
It helps you select and set images and sounds when connecting AV devices.
These buttons are used for teletext (on TELETEXT models only) , Programme edit.
TELETEXT BUTTONS
These buttons are used for teletext. For further details, see the ‘Teletext’ section.
PIP
Switches the sub picture PIP, DW mode.
Coloured · buttons


Allows you to navigate the on-screen menus and adjust the system settings to your preference.
Selects a programme. Selects numbered items in a menu.
Controls some video cassette recorders or DVD players. Control connected AV devices by pressing the / / / , OK buttons and buttons for G, A, l l, FF and GG. (The Ô button does not provide such functions.)
I Open the battery compartment cover on the back and install the
I Install two 1.5V AAA batteries. Do not mix old or used batteries

TURNING ON THE TV
When your TV is turned on, you will be able to use its features.
Firstly, connect the power cord correctly.
At this stage, the TV switches to standby mode.
I In standby mode to turn TV on, press the , INPUT, P D / E( or P / ) button on the TV or press the POWER, TV, INPUT, P
/ , NUMBER(0~9) buttons on the remote control and the TV will switch on.
If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the Language, Location, Auto Tuning.
Note: a. It will automatically disappear after approx. 40 seconds unless a button is pressed. b. “In-Store” mode is only for shop display and not for general customer use. c. "Home” mode is the optimal setting for home environments, and is the TV's default mode. d. "In-Store" mode is the optimal setting for store environments. If a user modifies image quality data,
“In-Store” mode initializes the product to the image quality set by us after a certain period of time. e. The mode (Home, In-Store) can be changed by executing Factory Reset in the Option menu.
Press the P / or NUMBER buttons to select a programme number.
Press the +/- button to adjust the volume.
If you wish to switch the sound off, press the MUTE button.
You can cancel the Mute function by pressing the MUTE or +/- button.
Installation Guide

Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently.
Q. MENU
F 4 : 3 G
Zoom Setting 0 0 Sport Sport L + R To Set Off
Power Saving Backlight Picture Mode Sound Mode Multi Audio Programme Edit Sleep Timer
* Only PLASMA TV models
* Only LCD TV models
Press the Q.MENU button and then / button to display each menu.
Press the / button to select your desired Source.
Press the Q.MENU button to return to normal TV viewing.
Aspect Ratio

ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
Press the MENU button and then / button to display each menu.
Press the button and then / button to select a menu item.
Change the setting of an item in the sub or pull-down menu with / button. You can move to a higher level menu by pressing the OK or MENU button.
Auto Tuning Manual Tuning Programme Edit Favourite Programme
Picture Mode Colour Temperature
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
Advanced Aspect Ratio Picture Reset Screen TruMotion Demo
DE F G OK RETURN DE F G OK RETURN
Setup MENU Picture MENU Audio MENU
Music List Photo List Movie List DivX Reg. Code
Language SIMPLINK Key Lock ISM Method Power Saving Set ID Power Indicator Factory Reset
Clock Off Time On Time Sleep Timer Auto Sleep
* Only PLASMA TV models
* Only LCD TV models
DE F G OK RETURN DE F G OK RETURN
Time MENU Option MENU
NOTE !
a. The OSD (On Screen Display) function enables you to adjust the screen status conveniently since it
provides graphical presentation. b. In this manual, the OSD (On Screen Display) may be different from your TV’s because it is just example
to help the TV operation. c. In the teletext mode and USB mode, menus are not displayed.

Up to 100 TV stations can be stored by programme numbers (0 to 99). Once you have preset the stations, you will be able to use the P / or NUMBER buttons to scan the stations you have programmed. Stations can be tuned using automatic or manual modes.
All stations which can be received are stored by this method. It is recommended that you use Auto tuning during installation of this TV.
P Press the MENU button and then / button to select the Setup menu.
Press the button and then / button to select Auto Tuning.
Auto Tuning Manual Tuning Programme Edit Favourite Programme
Press the button and then / button to select System.
Press the / button to select a TV system menu; BG: PAL B/G, SECAM B/G (Europe / East Europe / Asia /
NewZealand / M.East / Africa / Australia) I : PAL I/II (U.K. / Ireland / Hong Kong / South Africa) DK: PAL D/K, SECAM D/K (East Europe / China / Africa / CIS) M : (USA / Korea / Philippines)
To Set Auto Tuning G
Auto Tuning Manual Tuning Programme Edit Favourite Programme
Press the / button to select Storage From.
Press the / button or NUMBER buttons to select the ini- tial programme number. If you use NUMBER buttons, any number under 10 is entered with a numeric ‘0’ in front of it, i.e.‘05’ for 5.
System Storage From Search
Press the / button to select Search.
Press the button to begin auto tuning. All receivable stations are stored.
To stop auto tuning, press the RETURN button. When auto tuning is complete, the Programme edit menu appears on the screen. See the Programme edit section to edit the stored programme.
3 4 5 6 7
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

MANUAL PROGRAMME TUNING
Manual programme lets you manually tune and arrange the stations in whatever order you desire.
Press the MENU button and then / button to select the Setup menu.
Press the button and then / button to select Manual Tuning.
Press the button and then / button to select Storage.
Press the / button or NUMBER buttons to select the desired programme number (0 to 99). If you use NUMBER buttons, any number under 10 is entered with a numeric ‘0’ in front of it, i.e. ‘05’ for 5.
Press the / button to select System.
Press the / button to select a TV system menu; BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia /
Auto Tuning Manual Tuning Programme Edit Favourite Programme
NewZealand / M.East / Africa / Australia) I : PAL I/II (U.K. / Ireland / Hong Kong / South Africa) DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS) M : (USA / Korea / Philippines)
Press the / button to select Band.
Press the button and then / button to select V/UHF or Cable.
Auto Tuning Manual Tuning Programme Edit Favourite Programme
Press the / button to select Channel.
To Set Manual Tuning G
You can select the desired programme number with the / button or NUMBER buttons. If possible, select the programme number directly with the number buttons. Any number under 10 is entered with a numeric ‘0’ in front of it, i.e. ‘05’ for 5.
Press the / button to select Search.
Press the / button to commence searching. If a station is found the search will stop.
Storage System Band Channel Fine Search Name Booster
Press the OK button to store it.
To store another station, repeat steps 3 to 13.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
7 3 4 5 6
8 9 10 11 12


Normally fine tuning is only necessary if reception is poor.
Press the MENU button and then / button to select the Setup menu.
Press the button and then / button to select Manual Tuning.
Press the button and then / button to select Fine.
Press the button and then / button to fine tune for the best picture and sound.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.


You can assign a station name up to five characters to each programme number.
Press the MENU button and then / button to select the Setup menu.
Press the button and then / button to select Manual Tuning.
Press the button and then / button to select Name.
Press the button and then / button. You can use a blank, +, -, the number 0 to 9 and the alphabet A to Z.
Press the / button to select the position and make your choice of the second character, and so on.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.


In some models, Booster is an optional function. Only a set with Booster can perform this function.
If reception is poor, select Booster to On. When the signal is strong, select “OFF”.
Press the MENU button and then / button to select the SETUP menu.
Press the button and then / button to select Manual Tuning.
Press the button and then use / button to select Booster.
Press the button and then use / button to select On or Off.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Storage System Band Channel Fine Search Name Booster Booster G

PROGRAMME EDIT
This function enables you to delete or skip stored programmes. Also you can move some stations to other programme numbers or copy a blank station data into the selected programme number.
Press the MENU button and then / button to select the Setup menu.
Press the button and then / button to select Programme Edit.
Press the button to display the Programme edit menu.
A Deleting a programme
1.Select a programme to be deleted with the / / / button. 2.Press the RED button twice. The selected programme is deleted, all the following programmes are shifted up one position.
TIME SIZE UPDATE REVEAL
INDEX HOLD TEXT PIP
A Copying a programme
1.Select a programme to be copied with the / / / button. 2.Press the GREEN button. All the following programmes are shifted down one position.
Auto Tuning Manual Tuning Programme Edit Favourite Programme
A Moving a programme
1.Select a programme to be moved with the / / / button. 2.Press the YELLOW button. 3.Move the programme to the desired programme number with the / / / button. 4.Press the YELLOW button again to release this function.
Auto Tuning Manual Tuning Programme Edit Favourite Programme
A Skipping a programme number
To Set Programme Edit G
1.Select a programme number to be skipped with the / / / button. 2.Press the BLUE button. The skipped programme turns to blue. 3.Press the BLUE button again to release the skipped programme. When a programme number is skipped it means that you will be unable to select it using the / button during normal TV viewing. If you wish to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or table menu.
0 C 03 5 S 69 1 BLN 03 6 S 17 2 C 12 7 S 22 3 S 66 8 C 09 4 S 67 9 C 11
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

This function lets you select your favourite programmes directly.
Repeatedly press the FAV button to select stored favourite programmes.
LIST Q.VIEW
Press the MENU button and then / button to select the Setup menu.
Auto Tuning Manual Tuning Programme Edit Favourite Programme
Press the button and then / button to select Favourite Programme.
Press the button.
Auto Tuning Manual Tuning Programme Edit Favourite Programme Favourite Programme G
Press the / button to select -.
-
Select a desired programme with the / button or NUMBER buttons. Any number under 10 is entered with a numeric ‘0’in front of it, i.e.‘05’ for 5.
2 3 4 5
To store another programme, repeat steps 4 to 5. You can store up to 8 programmes.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Setup · Setup

SELECTING THE PROGRAMME LIST

You can check which programmes are stored in the memory by displaying the programme list.
A Displaying programme list
Press the LIST button to display the Programme list menu. The programme list appears on the screen. One programme list contains ten programmes as shown.

a. You may find some blue programmes. They have been set up
to be skipped by auto programming or in the programme edit mode. b. Some programmes with the channel number shown in the
programme list indicate there is no station name assigned.
A Selecting a programme in the programme list
Select a programme with the / / / button. Then press the OK button. The TV switches to the chosen programme number.
A Paging through a programme list
There are 10 programme table pages in which contain 100 pro grammes. Pressing the / / / button repeatedly turns the pages.
1 BLN 03 6 S 17
2 C 12 7 S 22
3 S 66 8 C 09
Press the LIST button to return to normal TV viewing.
F G DE OK
Programme List

This function operates only with devices with the SIMPLINK logo. Please check the SIMPLINK logo.
The product might not function properly when using it with other products with HDMI-CEC function.
This allows you to control and play other AV devices connected to the display through HDMI cable without additional cables and settings.
If you do not require the SIMPLINK menu, select “Off”.
Press the MENU button and then / button to select the Option menu.
INDEX HOLD TEXT PIP
Press the button and then / button to select SIMPLINK.
Language SIMPLINK Key Lock ISM Method Power Saving Set ID Power Indicator Factory Reset
Press the button and then / button to select On or Off.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Language SIMPLINK Key Lock ISM Method Power Saving Set ID Power Indicator Factory Reset
Option · Option · Off On

SIMPLINK Functions
Disc playback Control connected AV devices by pressing the / / / , OK, G, A, l l, FF and GG buttons. (The Ô button does not provide such functions)
Direct Play After connecting AV devices to the TV, you can directly control the devices and play media without additional settings.
Select AV device Enables you to select one of the AV devices connected to the TV and operate it.
Power off all devices When you switch off the TV, all connected devices are turned off.
Switch audio-out Offers an easy way to switch audio-out.
Sync Power On The television set will change automatically to turn on mode, after the Player with Simplink function start to reproduce through connection HDMI.
* A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does not provide this function.
SIMPLINK Menu Press the / / / button and then OK button to select the desired SIMPLINK source.
TV viewing : Switch to the previous TV programme regardless of the current mode.
DISC playback : Select and play discs. When multiple discs are available, the titles of the discs are conveniently displayed at the bottom of the screen.
VCR
When device is not connected (displayed in gray)
VCR playback : Control the connected VCR.
HDD Recordings playback : Control recordings stored in HDD.
When a device is connected (displayed in bright colour)
Audio Out to Home theater/Audio Out to TV : Select Home theater or TV speaker for Audio Out.
NOTE !
G Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal and Side terminal (HDMI
terminal) of the SIMPLINK device with the HDMI cable.
G After connecting the HDMI terminal for the home theatre with SIMPLINK function using the above
method, connect the VARIABLE AUDIO OUT terminal on the back of the TV to the VARIABLE AUDIO IN terminal on the back of the SIMPLINK device with the VARIABLE AUDIO OUT cable.
G When operating an external device with SIMPLINK, press the TV button from the MODE button on the
remote control.
G When you switch the Input source using the INPUT button on the remote control, you can stop the
operation of a device controlled by SIMPLINK.
G When you select or operate a media device with home theatre function, the speaker automatically
switches to home theatre speaker (HT speaker).
Selected Device

The TV can be set so that the remote control is needed to control it. This feature can be used to prevent unauthorized viewing.
This TV is programmed to remember which option it was last set to even if you turn the TV off.
Press the MENU button and then / button to select the Option menu.
Language SIMPLINK Key Lock ISM Method Power Saving Set ID Power Indicator Factory Reset
Press the button and then / button to select Key Lock.
Press the button and then / button to select On or Off.
Language SIMPLINK Key Lock ISM Method Power Saving Set ID Power Indicator Factory Reset
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
G In Key Lock ‘On’, if the TV is turned off, press the r / I, INPUT, P D / E( or P / ) button on the TV or POWER, INPUT, TV, P / or NUMBER buttons on the remote control.
G With the Key Lock On, the display ‘Key Lock On’ appears on the screen if any button on the front
panel is pressed while viewing the TV.

AV MODE
You can select the optimal images and sounds when connecting AV devices to external input.
WATCHING TV / PROGRAMME CONTROL
Game Sport
Press the AV MODE button repeatedly to select the desired source.
Press the RETURN button to return to normal TV viewing.

When connecting the USB device When you connect a USB device, this screen is displayed, automatically. In USB device, you can not add a new folder or delete the existing folder.
Connect the USB device to the USB IN jacks on the side of TV.
Press the button.
Press the / button to select the desired item.
Press the OK button.

Manufactured under license from Dolby Laboratories. “Dolby “and the double-D symbol are trademarks of Dolby Laboratories.
PHOTO MUSIC MOVIE
NOTE !
G In USB mode, P D / E( or P / ), +/- buttons on the TV are used to navigate (up/down/left/right).
G Only a USB storage device is recognizable. Digital camera and mobile phone are not supported.
G If the USB storage device is connected through a USB hub, the device is not recognizable.
G A USB storage device using an automatic recognition programme may not be recognized.
G A USB storage device which uses its own driver may not be recognized.
G In case of a card reader, up to one memory cards are concurrently recognizable.
G The recognition speed of a USB storage device may depend on each device.
G Please do not turn off the TV or unplug the USB device when the connected USB storage device is working.
When such device is suddenly separated or unplugged, the stored files or the USB storage device may be damaged.
G Please do not connect the USB storage device which was artificially maneuvered on the PC. The device may cause
the product to malfunction or fail to be played. Never forget to use only a USB storage device which has normal music files or image files.
G Please use only a USB storage device which was formatted as a FAT32 file system provided with the Windows
operating system. In case of a storage device formatted as a different utility programme which is not supported by Windows, it may not be recognized.
G Please connect power to a USB storage device which requires an external power supply. If not, the device may
not be recognized.
G Please connect a USB storage device with cable is offered by USB maker. If connected with cable is not offered
by USB maker or an excessively long cable, the device may not be recognized.
G Some USB storage devices may not be supported or operated smoothly.
G If the name of a folder or file is too long, it will not be displayed or recognized.
G File alignment method is based on storage order in USB storage device.
G Please backup the important file because a data of USB device may be damaged. Data management is consumer's
responsibility and in consequence the manufactures does not cover the product bearing data damage.
G If the quantity of folders and files is over 1,000, it will not be displayed or recognized about exceeded files and
folders.
G It is supported for only primary partition. If there is an extended partition, it is not displayed or recognized.
USB memory stick

PHOTO LIST
It is available to playback only the photo file(*.jpg) in the USB device. The On Screen Display may be different from your set. Images are an example to assist with the TV operation.

Listen to music while viewing photos in full size.
Set up the menu in Full-Sized Screen
You can change the settings to display photos stored on a USB device, on a full-sized screen. Detailed operations are available on full-sized photo view screen.

Use the / button to select the desired photos.
The selected photo is displayed in full size and show up the menu.

(Rotate) : Rotate photos. : Display the previous photo viewing. : Display the next photo viewing. : Stop the viewing the photos. : Hide the menu on the full-sized screen.
I To see the menu again on the full-sized screen,
Press RETURN button to return to TV viewing or press
The aspect ratio of a photo may change the size of the photo displayed on the screen in full size.
I If JPEG Viewing is operated, it should be pressed the

Use the / button to select the desired photos.
JMJ001
JMJ002
JMJ003
Press the button to select
1366x768 1/1
Press the OK button.
OK Move Move Page Exit
Stop: Stop the viewing the slide show. : Hide the menu on the full-sized screen.

I To see the menu again on the full-sized screen,
press OK button.
Showing.. 1/17
Press the button to select
Use / button to control the time interval of the slide show.
KY102
Press the OK button to store it.
JMJ002
JMJ003
Press the button to select
1366x768 1/1
Press the OK button to listen to music(BGM) while viewing photos in full size. Set the music device and album in Option.
OK Move Move Page Exit
I You should memorize FAV list to operate this
function in MUSIC LIST.
KY102
JMJ001
Press RETURN button to return to TV viewing or press button to return to the X-STUDIO menu.
JMJ003
I If Slideshow/BMG function is operated, it should be
1366x768 1/1
pressed the button after pressing the STOP button.
OK Move Move Page Exit
NOTE !
If it is Progressive JPEG format, some photos may be not decoded. If you do not press any button for 4 hours during the Slide show and BGM(Back Ground Music), it will be stopped. If the width of resolution is over 4800, it is not supported. When loading, some buttons may not work.

MUSIC LIST
Purchased music files(*.MP3) may contain copyright restrictions. Playback of these files may not be support- ed by this model. Music file on your USB device can be played by this unit. The On Screen Display may be different from your set. Images are an example to assist with the TV operation.

Delete All : Delete all music in music list.
a. If you want to listen to music, use the / button to select music. b. Press the OK button to play the music. c. All music in selected folder is played, repeatedly.
a. If you want to listen to several music in sequence,
use the / button to select music. b. Press FAV button and then use OK button to
I When FAV button is pressed, is displayed and
then it is possible to edit music list. c. To make music list, repeat steps a to b. d. Press button and then use OK button to play music in music list. e. Up to 30 files are stored.
Press RETURN button to return to TV viewing or press
I If MP3 playing is operated, it should be pressed the
button after pressing the STOP button.

I If you don't press any button for a while during
the playing, the play information box (as shown in the below) will float as a screen saver.
I The ‘Screen Saver’?
Screen saver is to prevent screen pixel damage due to an fixed image remaining on the screen for a extended period of time.
I If you press OK, A, RETURN buttons, screen saver is
stopped.
NOTE !
When music is playing, is displayed in Back of the music title. A music downloaded from a paid service with copyright protection does not start but displays inappropriate information in playtime.
The FF ,GG buttons on the remote control are not available in this mode. Customer should note that permission is required in order to download MP3 files form the internet, Our company has no right to quarantee such permission, Permission should always be sought from the copyright owner. When loading, some buttons may not work. MP3 files are supported as follows. Sampling Frequency : 32 ~ 48kHz Bit rate : 32 ~ 320kbps

MOVIE LIST
The movie list is activated once USB is detected. It is used when playing movie files on TV. Displays the movies in the USB folder and supports Play. Allows playback of all movies in the folder and user desired files. Editing such as delete and add is not allowed. It is a movie list that displays folder information and Divx file.
Movie List
Moves to upper level file
Corresponding buttons on the remote control
SA500005
SA500006
OK Move Move Page Exit
List · Up Folder

Use the button to select the desired movie titles.
Press the OK button to play the movie and show up the menu.
ON OFF Control Language Position Sync ARC
D To Set Hide
Control : Turns the subtitle display on and off during movie play. Language : Changes the Language Group of the subtitle during movie play. Position : Changes the position of the subtitle either up or down during movie play. Sync : Adjusts the time synchronisation of the subtitle from -5 secs ~ +5 secs by steps of 1 secs during movie play.
I To see the menu again on the full-sized screen, press OK button.
Press RETURN button to return to TV viewing or press button to return to the X-STUDIO menu.
I If movie playing is operated, it should be pressed the button after pressing the STOP button.
If you do not press any button for 10 minutes during Pause state, it will be stopped. When loading, some buttons may not work.
G When DivX is playing, if you press the OK button and then select language, this message is displayed.
Subtitle Language Group F Latin 1 G
Press the / / / button to select the desired option. Supports up to Mpeg, Mp3, PCM, Dolby D file.
Audio Language Dolby D
Subtitle Language

DIVX REGISTRATION CODE
Confirm the DivX registration code number of the TV. Using the registration number, movies can be rented or purchased at www.divx.com/vod With a DivX registration code from other TV, playback of rented or purchased DivX file is not allowed. (Only DivX files matched with the registration code of the purchased TV are playable.)
Press the MENU button and then use / button to select the USB menu.
Press the button and then use / button to select DivX Reg. Code.
Press the button to start DivX Reg. Code.
Music List Photo List Movie List Divx Reg. Code Divx Reg. Code G

: xxxxxxxx
Press the RETURN button to return to normal TV viewing.

Movie files are supported as follows. Resolution : under 720x480(720x576) WxH pixels. Frame rate : under 30 frames/sec
Video Codec : MP 43, DIVX_3_11, DIVX_4_12, DIVX_5_0, XVID, MP4S, RMP4, MP4V, _3IVX.
DivX Registration Code · To Set

WATCHING PIP(PICTURE-IN-PICTURE)
PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the other source will show a smaller inset image. PIP function is available in the Component, RGB, HDMI mode. (For FHD models, it can support TV, AV1, AV2 mode.(except 32/42LG80F*))
PIP PIP Input PIP PR PIP Size PIP Position
F PIP G TV C 07 7 Small
Watching PIP/Double Window
Press the PIP button and then press the / / / button to change the PIP options as shown below.

Press the PIP button and then press the / / / button to select a programme for the sub picture. The selected programme number is displayed just below the programme number of main picture.
Press the PIP button and then press the / / / button to select the PIP Input source for the sub picture. (Sub picture can be selected only TV, AV1, AV2)
Press the PIP button and then press the / / / button to adjust the sub picture size.
Press the PIP button and then press the / / / button to adjust the sub picture position.

PICTURE SIZE (ASPECT RATIO)CONTROL
You can watch the screen in various picture formats; 16:9, Original, 4:3, 14:9, Zoom1/2 and Just Scan.
Just Scan works in the following mode: Component (720p/1080i/1080p), HDMI (720p/1080i/1080p)
If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible.
You can adjust the enlarge proportion using button.
This function works in the following signal.

4:3
16:9

Original




G You can only select 4:3, 16:9 (Wide) in Component, HDMI, RGB(PC) mode.
G In HDMI/Component (over 720p) mode, Just Scan is available.
Zoom1 DE · Zoom2 DE

PRESET PICTURE SETTINGS
Picture Mode-Preset
Picture Mode adjusts the TV for the best picture appearance. Select the preset value in the Picture Mode menu based on the programme category.
Intelligent Sensor(Only LCD TV models), Vivid, Standard, Cinema, Sport and Game are programmed for optimum picture reproduction at the factory and cannot be changed.
When the Intelligent Sensor function is on, the most suitable picture is automatically adjusted according to the surrounding conditions.(Only LCD TV models)
Picture Mode Colour Temperature
Press the MENU button and then / button to select the Picture menu.
Advanced Aspect Ratio Picture Reset Screen
Press the button and then / button to select Picture Mode.
Press the button and then / button to select Intelligent Sensor(Only LCD TV models), Vivid, Standard, Cinema, Sport, Game, User1 or User2.
Picture Mode Colour Temperature
Intelligent Sensor Vivid Standard Cinema Sport Game User1 User2
Advanced Aspect Ratio Picture Reset Screen
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Picture · Picture · Picture Mode G

To initialize values (reset to default settings), select the Cool option.
Choose one of three automatic colour adjustments. Set to warm to enhance hotter colours such as red, or set to cool to see less intense colours with more blue.
This menu is activated after selecting “User1” or “User2” in the Picture Mode.
Picture Mode Colour Temperature
Press the MENU button and then / button to select the Picture menu.
Advanced Aspect Ratio Picture Reset Screen
Press the button and then / button to select Colour Temperature.
Press the button and then / button to select either Cool, Medium, Warm or User.
Picture Mode Colour Temperature
Cool Medium Warm User
Advanced Aspect Ratio Picture Reset Screen
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Picture · Picture · Colour Temperature G

MANUAL PICTURE ADJUSTMENT
Picture Mode-User Option
Backlight To control the brightness of the screen, adjust the brightness of LCD panel. Contrast Adjusts the difference between light and dark levels in the picture. Brightness Increases or decreases the amount of white in the picture. Colour Adjusts intensity of all colours. Sharpness Adjusts the level of crispness in the edges between the light and dark areas of the picture. The lower the level, the softer the image. Tint Adjusts the balance between red and green levels.
Picture Mode Colour Temperature
Press the MENU button and then / button to select the Picture menu.
Advanced Aspect Ratio Picture Reset Screen
Press the button and then / button to select Picture Mode.
Press the button and then / button to select User1 or User2.
Picture Mode Colour Temperature
Intelligent Sensor Vivid Standard Cinema Sport Game User1 User2
Press the button and then / button to select the desired picture option (Backlight(Only LCD TV modes), Contrast, Brightness, Colour, Sharpness and Tint).
Advanced Aspect Ratio Picture Reset Screen
Press the / button to make appropriate adjustments.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Backlight 50 Contrast 100 Brightness 50 Colour 50 Sharpness 50 Tint 0
G You cannot adjust colour, sharpness and tint in the
RGB-PC mode.
E


To adjust red, green, blue to any colour temperature you prefer.
This menu is activated after selecting “User1” or “User2” in the Picture Mode.
Press the MENU button and then / button to select the Picture menu.
Press the button and then / button to select Colour Temperature.
Press the button and then / button to select User.
Press the button and then / button to select Red, Green or Blue.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

- PICTURE IMPROVEMENT TECHNOLOGY
XD is LG electronic's unique picture improving technology to display a real HD source through an advanced digital signal processing algorithm.
It is not possible to use this function in RGB-PC mode.
Press the MENU button and then / button to select the Picture menu.
Picture Mode Colour Temperature
Press the button and then / button to select XD.
Advanced Aspect Ratio Picture Reset Screen
Press the button and then / button to select Auto or Manual.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Picture Mode Colour Temperature XD Advanced Aspect Ratio Picture Reset Screen
G
This menu is activated after selecting the User1 or User2 of Picture Mode.
Press the button and then / button to select XD Contrast, XD Colour or XD NR.
Press the button and then / button to select Off, Low or High. Select Off, Low, High, Adaptive.(only XD NR)
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
according to the brightness of the reflection.
automatically to reproduce as close as possible to natural colours.
does not damage the original picture.


High gamma values display whitish images and low gamma values display high contrast images.
It is not possible to use this function in RGB-PC mode.
Press the MENU button and then / button to select the Picture menu.
Press the button and then / button to select Advanced.
Press the button and then / button to select Gamma.
Press the button and then / button to select Low, Medium or High.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.


To set the TV up for the best picture quality for viewing films.
This feature operates only in Analog TV, AV, S-video and Component 480i/576i mode.(Film Mode only)
Press the MENU button and then / button to select
Press the button and then / button to select Advanced.
Press the button and then / button to select Film
Press the button and then / button to select On or Off.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

When you view a film this function adjust the TV to best picture quality. Adjusting the contrast and the brightness of the screen using the black level of the screen.
This function works in the following mode: RF(NTSC-M), AV, S-Video(NTSC-M, NTSC 4.43), COMPONENT or HDMI.
Picture Mode Colour Temperature
Press the MENU button and then / button to select the Picture menu.
Advanced Aspect Ratio Picture Reset Screen
Press the button and then / button to select Advanced.
Press the button and then / button to select Black Level.
Picture Mode Colour Temperature
Advanced Aspect Ratio Picture Reset Screen
Press the button and then / button to select Low or High.
A Low : The reflection of the screen gets darker.
A High : The reflection of the screen gets brighter.
Gamma Film Mode Black Level Eye Care
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.


It helps you adjust brightness when the screen is too bright to prevent dazzling. When selecting Picture Mode(Standard, Sport, Game, User1 and User2), you can operate this function.
Press the MENU button and then / button to select the Picture menu.
Press the button and then / button to select Advanced.
Press the button and then / button to select Eye Care.
Press the button and then / button to select On or Off.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Gamma Film Mode Black Level Eye Care Eye Care G

It is used for the best picture quality without any motion blur or judder when you enter a quick image or Film Source. This feature is disable in RGB-PC, HDMI-PC mode.
Press the MENU button and then / button to select the Picture menu.
Picture Mode Colour Temperature
Advanced Aspect Ratio Picture Reset Screen
Press the button and then / button to select Advanced.
Press the button and then / button to select TruMotion.
Picture Mode Colour Temperature
Press the / button to select Off, Low or High.
Advanced Aspect Ratio Picture Reset Screen
ting for standard use.
A High : Provides smoother picture movement.
result in noise.
Gamma Real Cinema Black Level Eye Care TurMotion TruMotion G
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.


Returns to the default factory setting for Picture Mode, Colour Temperature, XD, Advanced, Aspect Ratio.
Press the MENU button and then / button to select the Picture menu.
Press the button and then / button to select Picture Reset.
Advanced Aspect Ratio Picture Reset Screen Picture Reset G
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.


Use it to see the difference between TruMotion Demo on and TruMotion Demo off. It’s not available to use this function in RGB/HDMI-PC mode.
Press the MENU button and then / button to select the Picture menu.
Press the button and then / button to select TruMotion Demo.
Advanced Aspect Ratio Picture Reset Screen TruMotion Demo TruMotion Demo G


It helps you adjust the brightness of moving LED and sound when power is turned on.
Press the MENU button and then / button to select the Option menu.
Press the button and then / button to select Power Indicator.
Press the button and then / button to select Startup Sound(Only 32/37/42/47LG6***), Standby Light, Power Light or Demo Mode(Only 32/37/42/47LG6***).
Press the button and then / button to select your desired Source.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

A frozen or still picture from a PC/Video game displayed on the screen for prolonged periods will result in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain on the screen for prolonged periods.
White wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash.
Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the screen will move every 2 minutes.
Language SIMPLINK Key Lock ISM Method Power Saving Set ID Factory Reset
This function inverts the panel colour of the screen. The panel colour is automatically inverted every 30 minutes.
Press the MENU button and then / button to select the Option menu.
Language SIMPLINK Key Lock
ISM Method Power Saving Set ID Factory Reset
Normal White Wash Orbiter Inversion
Press the button and then / button to select ISM Method.
Press the button and then / button to select either Normal, White Wash, Orbiter or Inversion. If you do not need this function, set Normal.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.


This function allows you to reduce the power consumption of the TV.
Language SIMPLINK Key Lock ISM Method Power Saving Set ID Factory Reset
Press the MENU button and then / button to select the Option menu.
Press the button and then / button to select Power Saving.
Press the button and then / button to select power levels.
Language SIMPLINK Key Lock ISM Method Power Saving Set ID Factory Reset
Level 0 Level 1 Level 2 Level 3 Level 4
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

Use to quickly reset all the menu options to their original factory preset values. This function deletes all TV programmes.
Press the MENU button and then / button to select the Option menu.
Language SIMPLINK Key Lock ISM Method Power Saving Set ID Power Indicator Factory Reset
Press the button and then / button to select Factory Reset.
Press the button and then / button to select YES or NO.
Language SIMPLINK Key Lock ISM Method Power Saving Set ID Power Indicator Factory Reset Factory Reset G
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
F G OK RETURN


Auto Volume automatically remains on the same level of volume if you change programmes.
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
Press the MENU button and then / button to select the Audio menu.
Press the button and then / button to select Auto Volume.
Press the button and then / button to select On or Off.
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

You can select your preferred sound setting; SRS TSXT, Clear Voice, Standard, Music, Cinema, Sport or Game and you can also adjust the frequency of the equalizer.
Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate sound options based on the programme content.
SRS TSXT, Clear Voice, Standard, Music, Cinema, Sport and Game are preset for optimum sound quality at the factory and are not adjustable.
Press the MENU button and then / button to select the Audio menu.
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
Press the button and then / button to select Sound Mode.
Press the button and then / button to select SRS TSXT, Clear Voice, Standard, Music, Cinema, Sport, Game or User.
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
SRS TSXT Clear Voice Standard Music Cinema Sport Game User
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
G is a trademark of SRS Labs, Inc.
G TruSurround XT technology is incorporated under license from SRS Labs, Inc.


Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
Press the MENU button and then / button to select the Audio menu.
Press the button and then / button to select Sound Mode.
Press the button and then / button to select User.
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
SRS TSXT Clear Voice Standard Music Cinema Sport Game User
Select a frequency band by pressing the / button. Set the desired sound level with the / button.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.


You can adjust the sound balance of the speakers to the preferred levels.
Press the MENU button and then / button to select the Audio menu.
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
Press the button and then / button to select Balance.
Press the button and then / button to make desired adjustment.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

TV SPEAKERS ON/OFF SETUP
You can adjust the internal speaker status.
In TV, AV, COMPONENT, RGB[PC] and HDMI mode, internal speaker audio can be operational even though there is no video signal.
If you wish to use an external hi-fi system, turn off the TV internal speakers.
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
Press the MENU button and then / button to select the Audio menu.
Press the button and then / button to select TV Speaker.
Press the button and then / button to select On or Off.
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
TV Speaker G Off On
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
Select Monitor Out or Variable out to connect the audio outputs.
Press the MENU button and then / button to select the Audio menu.
Press the button and then / button to select Audio Out.
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out Audio Out G
Press the button and then / button to select Monitor Out or Variable out.
Monitor Out Variable Out
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

Superior quality of sound can be appreciated when used a speaker by the sliding mode function
Press the MENU button and then / button to select the Audio menu.
Press the button and then / button to select Sliding Mode.
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out
Press the button and then / button to select Open or Auto.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Sound Mode Auto Volume Balance 0 TV Speaker Audio Out Sliding Mode Sliding Mode G
G Speaker and related parts of the television can be damaged when the speaker is not put on action by a remote controller or control keys.








Audio · Audio · Open Auto

I/II
Stereo/Dual Reception
When a programme is selected, the sound information for the station appears with the programme number and station name.
Press the Q.MENU button and then / button to select the Multi Audio menu.
Press the / button to select the sound output.
MONO
STEREO
DUAL I, DUAL II, DUAL I+II
A Mono sound selection
If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the clarity of sound is improved. To switch back to stereo.
A Language selection for dual language broadcast
If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II.
DUAL I Sends the primary broadcast language to the loudspeakers. DUAL II Sends the secondary broadcast language to the loudspeakers. DUAL I+II Sends a separate language to each loudspeaker.

If the TV is equipped with a receiver for NICAM reception, high quality NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the type of broadcast received.
When NICAM mono is received, you can select NICAM MONO or FM MONO.
When NICAM stereo is received, you can select NICAM STEREO or FM MONO. If the stereo signal is weak, switch to FM MONO.
When NICAM dual is received, you can select NICAM DUAL I, NICAM DUAL II or NICAM DUAL I+II or FM MONO.
In AV, Component, RGB and HDMI mode, you can select output sound for the left and right loud- speakers.
Select the sound output.
L+R: Audio signal from audio L input is sent to the left loudspeaker and audio signal from audio
R input is sent to the right loudspeaker. L+L: Audio signal from audio L input is sent to left and right loudspeakers. R+R: Audio signal from audio R input is sent to left and right loudspeakers.

ON-SCREEN MENU LANGUAGE SELECTION

The menus can be shown on the screen in the selected language. First select your language.

Press the MENU button and then use / button to select the Option menu.
Press the button and then use / button to select Language.
Press the button and then use / / / button to select your desired language.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.


You must set the time correctly before using on/off timer function.
If current time setting is erased by a power failure or the TV is unplugged, reset the clock.
Clock Off Time On Time Sleep Timer Auto Sleep
Press the MENU button and then / button to select the Time menu.
Press the button and then / button to select Clock.
Press the button and then / button to set the hour.
Clock Off Time On Time Sleep Timer Auto Sleep
Press the button and then / button to set the minute.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

AUTO ON/OFF TIMER SETTING
The Off time function automatically switches the TV to standby at a preset time.
Two hours after the TV is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed.
Once the on time/off time is set, these functions operate daily at the preset time.
The Off time function overrides the On timer function if both are set to the same time.
The TV must be in standby mode for the On timer to work.
Clock Off Time On Time Sleep Timer Auto Sleep
Press the MENU button and then / button to select the Time menu.
Press the button and then / button to select On/Off Time. • To cancel On/Off Time function, select Off.
Press the button and then / button to set the hour.
Clock Off Time On Time Sleep Timer Auto Sleep
Press the button and then / button to set the minutes.
Clock Off Time On Time Sleep Timer Auto Sleep
07:00 PR 1 Vol. 8 On
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.


You do not have to remember to switch the TV off before you go to sleep. The sleep timer automatically switches the TV to standby after the preset time has elapsed.
Clock Off Time On Time Sleep Timer Auto Sleep
Press the MENU button and then / button to select the Time menu.
Press the button and then / button to select Sleep Timer.
Press the button and then / button to set the minute.
Clock Off Time On Time Sleep Timer Auto Sleep
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
G When you switch the TV off, the TV releases the preset sleep time.


If the TV set is switched on and there is no input signal, it will switch off automatically after 10 minutes.
Clock Off Time On Time Sleep Timer Auto Sleep
Press the MENU button and then / button to select the Time menu.
Press the button and then / button to select Auto Sleep.
Press the button and then / button to select On or Off.
Clock Off Time On Time Sleep Timer Auto Sleep Auto Sleep G
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

This feature is not available in all countries.
Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, television programmes, share prices and many other topics.
The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page num- ber. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext information.
Press the TEXT button to switch to teletext. The initial page or last page viewed appears on the screen. Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current page displayed. Press the TEXT or RETURN button to switch off teletext. The previous mode reappears.
SIMPLE TEXT
A Page selection
Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the correct page number. The P / button can be used to select the preceding or following page.

TOP TEXT
The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next group and the blue field indicates the next block.
With the blue button you can progress from block to block. Use the yellow button to proceed to the next group with automatic overflow to the next block. With the green button you can proceed to the next existing page with automatic overflow to the next group.
Alternatively the P button can be used. The red button return to the previous selection. Alternatively the P button can be used.
As with SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in TOP mode.
FASTEXT
The teletext pages are colour coded along the bottom of the screen and are selected by pressing the correspond- ing coloured button.
Press the button to select the index page. You can select the pages which are colour coded along the bottom line with corresponding coloured buttons. As with SIMPLE teletext mode, you can select a page by entering its three digit page number with the NUMBER buttons in FASTEXT mode. The P / button can be used to select the preceding or following page.

When viewing a TV programme, press this button to display the time at the top right hand corner of the screen. Press this button again to remove the display. In the teletext mode, press this button to select a sub page number. The sub page number is displayed at the bottom of the screen. To hold or change the sub page, press the RED/GREEN, P / or NUMBER buttons. Press again to exit this function.
Selects double height text. Press this button to enlarge the top half of the page. Press this button again to enlarge the bottom half of the page. Press this button again to return to the normal display.
TELETEXT
Displays the TV picture on the screen while waiting for a new teletext page. The display will appear at the top left hand corner of the screen. When the updated page is available then display will change to the page number. Press this button again to view the updated teletext page.
Press this button to display concealed information, such as solutions to riddles or puzzles. Press this button again to remove the information from the display.
Select the each index page.
Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages. The num- ber of sub pages and the sub page displayed is, usually, shown on the screen below the time. When this button is pressed the stop symbol is displayed at the top left-hand corner of the screen and the automatic page change is inactive. To continue press this button again.

TROUBLESHOOTING
The TV does not operate properly
I Check to see if there is any object between the TV and the remote control
causing an obstruction.
I Are batteries installed with correct polarity (+ to +, - to -)?
I Correct remote operating mode set: TV, STB etc.?
I Install new batteries.
I Is the sleep time set?
I Check the power control settings. Has the Power supply been interrupted.
I Is Auto sleep activated on this station.
The video function does not work.
I Check whether the TV is switched on.
I Try another channel. The problem may be with the broadcast.
I Is the power cord inserted correctly into the mains?
I Check your antenna direction and/or location.
I Test the mains outlet by plugging another TV into the same outlet.
I This is normal, the image is muted during the TV startup process. Please contact your
ly after switching on
service center, if the picture has not appeared after five minutes.
I Adjust Colour in menu option.
I Allow a sufficient distance between the TV and the VCR.
No or poor colour
I Try another channel. The problem may be with the broadcast.
I Are the video cables installed properly?
I Activate any function to restore the brightness of the picture.
Horizontal/vertical bars or picture shaking
I Check for local interference such as an electrical appliance or power tool.
I Station or cable channel experiencing problems, tune to another station.
I Station signal is weak, reposition the antenna to receive weaker stations.
I Check for sources of possible interference.
Lines or streaks in
I Check antenna (Change the position of the antenna).
I Check HDMI cable over version 1.3.
No picture when connecting
If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.

The audio function does not work.
I Press the +/- (or Volume) button.
I Sound muted? Press MUTE button.
I Try another channel. The problem may be with the broadcast.
I Are the audio cables installed properly?
No output from one
I Adjust Balance in menu option.
I A change in ambient humidity or temperature may result in an unusual noise when
the TV is switched on or off and does not indicate a fault with the TV.
I Check USB cable over version 2.0. No sound when connecting
I Check HDMI cable over version 1.3.
HDMI or USB *This feature is not available for all models.
There is a problem in PC mode. (Only PC mode applied)
I Adjust resolution, horizontal frequency, or vertical frequency.
The signal is out of
range.
I Check the input source.
Vertical bar or stripe
I Use Auto configure or adjust clock, phase, or H/V position.
on background & Horizontal Noise &
Screen colour is unstable or single
I Check the signal cable.
I Reinstall the PC video card.

MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV. Caution: Be sure to swith the power off and unplug the power cord before you begin any cleaning.
A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching on.
I To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
I Do not to use a wet cloth.
Extended Absence
CAUTION
If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power cord to protect against possible damage from lightning or power surges.

42PG6***
50PG6***
MODELS
50PG60UR-TA 50PG61UR-TA
60PG60UR-TA 60PG61UR-TA
42PG60UR-TA 42PG61UR-TA
1044.4 x 735.4 x 308.0 mm
1235.6 x 849.3 x 364.1 mm
1455 x 985 x 414 mm
41.1x 28.9 x 12.1 inches
48.6 x 33.4x 14.3inches
57.3 x 38.8 x 16.3 inches
(Width x Height x Depth)
1044.4 x 680.6 x 79.6 mm
1235.6 x 792.8 x 79.6 mm
1455 x 924.8 x 84.1 mm
41.1 x 26.7 x 3.1 inches
48.6x 31.2 x 3.1 inches
57.3x 36.4 x 3.3 inches
28 kg / 61.7 lbs
43.65 kg / 96.2 lbs
59.2 kg / 130.5 lbs
25 kg / 55.1 lbs
39.7kg / 87.5lbs
51.7 kg / 114 lbs
50PG7***
60PG7***
MODELS
50PG30FR-TD
50PG70FR-TB
60PG70FR-TB 60PG70FR-TA
1232 x 850 x 363.6 mm 48.5 x 33.5x 14.3inches
1235.6 x 849.3 x 364.1 mm 48.6 x 33.4x 14.3inches
1455 x 985 x 414 mm
57.3 x 38.8 x 16.3 inches
(Width x Height x Depth)
1232 x 793 x 84 mm 48.5x 31.2 x 3.3 inches
1235.6 x 792.8 x 79.6 mm 48.6x 31.2 x 3.1 inches
1455 x 924.8 x 84.1 mm
57.3x 36.4 x 3.3 inches
42.3 kg / 93.3 lbs 38.3kg / 84.4lbs
45.65 kg / 100.6 lbs 41.7kg / 91.9lbs
62.4 kg / 137.6 lbs
54.9 kg / 121 lbs
VHF: NZ1~E21, UHF: E21 ~ E69, CATV: S1 ~ S20, HYPER: S21 ~ S47
0 ~ 40°C / 32 ~ 104°F
-20 ~ 60°C / -4 ~ 140°F
I The specifications shown above may be changed without prior notice for quality improvement.

37LG6***
42LG6***
47LG6***
MODELS
32LG60UR-TA
37LG60UR-TA
42LG60FR-TA
47LG60FR-TA
805.6 x 626 x 333 mm
929 x 706.9x 374.7mm
1037.8 x 794.6 x 379.5 mm
1152.8 x 868.6 x 434.5 mm
(Width x Height x Depth)
31.7 x 24.6 x 13.1 inches
36.6x 27.8 x 14.8 inches
40.9x 31.3 x 14.9 inches
45.4 x 34.2 x 17.1 inches
805.6x 587.4x 96.2mm
929 x 665x 98.7 mm
1037.8x 747x 80.8mm
1152.8 x 820.8 x 79 mm
31.7 x 23.1 x 3.7 inches
36.6x 26.2 x 3.9 inches
40.9 x 29.4 x 3.2 inches
45.4 x 32.3x 3.1 inches
14.4 kg / 31.7 lbs
18.1 kg / 39.9 lbs
21.4 kg / 47.2 lbs
32.8 kg / 72.3 lbs
12.2 kg / 26.9 lbs
21.2 kg / 46.7 lbs
20.4 kg / 45 lbs
27.2 kg / 60 lbs
47LG7***
52LG7***
MODELS
42LG70YR-TA
47LG70YR-TA
52LG70YR-TA
1026.2 x 734.0 x 293.4 mm
1140.4 x 820.1 x 342.9 mm
1284.4 x 898.6 x 342.9 mm
40.4 x 28.8 x 11.5 inches
44.8 x 32.2 x 13.5 inches
50.5 x 35.3 x 13.5 inches
(Width x Height x Depth)
1026.2 x 687.9 x 111.8 mm
1140.4 x 764.8 x 129.0 mm
1284.4 x 844.6 x 129.5 mm
40.4 x 27.0 x 4.4 inches
44.8 x 30.1 x 5.0 inches
50.5 x 33.2 x 5.0 inches
21.7 kg / 47.8 lbs
30.1 kg / 66.3 lbs
39.9 kg / 87.9 lbs
19.1 kg / 42.1 lbs
25.4 kg / 55.9 lbs
35.2kg / 77.6lbs
32LG8***
42LG8***
47LG75**
MODELS
32LG80UR-TA 32LG80FR-TA
42LG80FR-TA
47LG75QR-TA
1063 x 722.2 x 293.3 mm
1140.4 x 820.1 x 342.9 mm
830 x 581.3 x 232 mm
41.9x 28.4 x 11.5 inches
44.8 x 32.2 x 13.5 inches
(Width x Height x Depth)
32.7 x 22.9 x 9.1 inches
1140.4 x 764.8 x 129.0 mm
830x 518.7x 108.5mm
41.9 x 25.6 x 3.9 inches
44.8 x 30.1 x 5.0 inches
32.7 x 20.4 x 4.3 inches
24.65 kg / 54.3 lbs
30.1 kg / 66.3 lbs
13.79 kg / 30.4 lbs
22.05 kg / 48.6 lbs
25.4 kg / 55.9 lbs
12.32 kg / 27.2 lbs
VHF: NZ1~E21, UHF: E21 ~ E69, CATV: S1 ~ S20, HYPER: S21 ~ S47
0 ~ 40°C / 32 ~ 104°F
-20 ~ 60°C / -4 ~ 140°F
I The specifications shown above may be changed without prior notice for quality improvement.

The remote control is a multi brand or universal remote. It can be programmed to operate most remote controlled devices from other manufacturers.
Testing your remote control. To find out whether your remote control can operate other components without programming, turn on a component such as a STB and press the corresponding mode button (such as a DVD or STB) on the remote control, while pointing at the component. Test the POWER and P / buttons to see if the component responds correctly. If the component does not operate correctly, the remote control requires programming to operate the device.
Switch on the component to be programmed, then press the corresponding mode button (such as a DVD or STB) on the remote control. The remote control button of the desired device is illumintated.
Press the MENU and MUTE buttons simultaneously, the remote control is ready to be programmed with the code.
Enter a code number using the number buttons on the remote control. Programming code numbers for the corresponding component can be found on the following pages. If the code is correct, the device will turn off.
Press the MENU button to store the code.
Test the remote control functions to see if the component responds correctly. If not, repeat from step 2.

Programming code
Brand Codes Brand Codes Brand Codes DVD
APEX DIGITAL 022 DENON 020 014 GE 005 006 HARMAN KARDON 027 JVC 012 LG 001 010 016 025 MAGNAVOX 013 MARANTZ 024
MITSUBISHI 002 NAD 023 ONKYO 008 017 PANASONIC 003 009 PHILIPS 013 PIONEER 004 026 PROCEED 021 PROSCAN 005 006
RCA 005 006 SAMSUNG 011 015 SONY 007 THOMPSON 005 006 TOSHIBA 019 008 YAMAHA 009 018 ZENITH 010 016 025
ALPHASTAR DSR 123 AMPLICA 050 Astro Philips(ML) 159 Astro Thompson(ML) 160 Astro Nokia(ML) 161 BIRDVIEW 051 126 129 CHANNEL MASTER 013 014 015 018 036 055 CHAPARRAL 008 009 012 077 CITOH 054 CURTIS MATHES 050 145 DRAKE 005 006 007 010 011 052 112 116 141 DX ANTENNA 024 046 056 076 ECHOSTAR 038 040 057 058 093 094 095 096 097 098 099 100 122 ELECTRO HOME 089 EUROPLUS 114 FUJITSU 017 021 022 027 133 134 GENERAL INSTRUMENT 003 004 016 029 031 059 101 HITACHI 139 140
HOUSTON TRACKER 033 037 039 051 057 104 HUGHES 068 Humax(SL) 158 JANIEL 060 147 JERROLD 061 KATHREIN 108 LEGEND 057 LG 001 LUTRON 132 LUXOR 062 144 MACOM 010 059 063 064 065 MEMOREX 057 NEXTWAVE 028 124 125 NORSAT 069 070 PACE SKY SATELLITE 143 PANASONIC 060 142 PANSAT 121 PERSONAL CABLE 117 PHILIPS 071 PICO 105 PRESIDENT 019 102 PRIMESTAR 030 110 111 PROSAT 072 PSI(TH) 157 RCA 066 106
REALISTIC 043 074 SAMSUNG 123 SATELLITE SERVICE CO 028 035 047 057 085 Samart(TH) 156 SCIENTIFIC ATLANTA 032 138 SONY 103 STARCAST 041 SUPER GUIDE 020 124 125 TEECOM 023 026 075 087 088 090 107 130 137 TOSHIBA 002 127 True Vision(TH) 155 UBC(TH) 153 UBC/SAMART(TH) 154 UNIDEN 016 025 042 043 044 045 048 049 078 079 080 086 10 135 136 VIEWSTAR 115 VTC(VN) 162 WINEGARD 128 146 ZENITH 081 082 083 084 091 120

1. How to Connect
A Connect your wired remote control to the Remote Control port on the TV.
Single pulse, modulated with 37.917KHz signal at 455KHz
FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3
A Configuration of frame
Lead code Low custom code High custom code Data code Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
A Lead code
4.5 ms 9 ms
0.55 ms
2.25 ms 9 ms
Bit ”0” Bit ”1”
0.56 ms
0.56 ms
1.12 ms
2.24 ms
The waveform is transmitted as long as a key is depressed.

Code Function Note (Hexa)
Code Function Note (Hexa)
0B INPUT R/C Button
09 MUTE R/C Button
08 POWER R/C Button (Power On/Off)
53 LIST R/C Button
60 PIP R/C Button
10 ~ 19 Number Key 0 ~ 9 R/C Button
43 MENU R/C Button
1E FAV R/C Button
5B RETURN R/C Button
1A Q.VIEW R/C Button
20 TEXT R/C Button
B0 SIZE R/C Button
8F INDEX R/C Button
B1 TIME R/C Button
44 OK R/C Button
BD REVEAL R/C Button
72 RED R/C Button
8E HOLD R/C Button
71 GREEN R/C Button
BA UPDATE R/C Button
63 YELLOW R/C Button
7E SIMPLINK R/C Button
61 BLUE R/C Button
B1 A Stop R/C Button
02 + R/C Button
B0 G Play R/C Button
BA l lPause R/C Button
00 P R/C Button
8F FF Rew R/C Button
01 P R/C Button
8E GG FF R/C Button
30 AV MODE R/C Button
45 Q.MENU R/C Button
BD Ô(Record) R/C Button

Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the TV’s functions externally. Connect the serial port of the control device to the RS-232C jack on the TV back panel. RS-232C connection cables are not supplied with the TV.


HDMI IN HDMI IN HDMI DVI IN HDMI DVI IN

RS-232C Configurations
7-Wire Configurations (Standard RS-232C cable)
PC TV
RXD 2 3 TXD TXD 3 2 RXD GND 5 5 GND DTR 4 6 DSR DSR 6 4 DTR RTS 7 8 CTS CTS 8 7 RTS
RXD 2 3 TXD TXD 3 2 RXD GND 5 5 GND DTR 4 6 DTR DSR 6 4 DSR RTS 7 7 RTS CTS 8 8 CTS
D-Sub 9 D-Sub 9
D-Sub 9 D-Sub 9

Language SIMPLINK Key Lock ISM Method Power Saving Set ID Factory Reset
Use this function to specify a set ID number. Refer to ‘Real Data Mapping’1. See page p.112.
Press the MENU button and then use / button to select the OPTION menu.
Press the button and then use / button to select Set ID.
Press the button and then use / button to adjust Set ID to choose the desired TV ID number.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
AUse a crossed (reverse) cable.
3-Wire Configurations(Not standard)

COMMAND1 COMMAND2 DATA (Hexadecimal) COMMAND1 COMMAND2
Transmission / Receiving Protocol
[Command1][Command2][ ][Set ID][ ][Data][Cr] [Command2][ ][Set ID][ ][OK][Data][x]
The TV transmits ACK (acknowledgement) based on this for- mat when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
[Command 2] : Second command to control the set.
number in Setup menu. Adjustment range is 1~ 99. When selecting Set ID ‘0’, every connected TV is controlled. Set ID is indicated as decimal (1~ 99)
on menu and as Hexa decimal (0x0~ 0x63) on transmission/receiving protocol.
[Command2][ ][Set ID][ ][NG][Data][x]
[DATA] : To transmit command data.
TV transmits ACK(acknowledgement) based on this format when receiving abnormal data form non-viable functions or communication errors. [Command 2] : use as command. [Set ID]: use the small character, if set ID is 10, TV will send the ‘0’, ‘a’ [Data]: use the small character, if data is 0xab, TV will send the ‘a’, ‘b’. [NG]: use the large character.
Transmit ‘FF’ data to read status of comand.

To control Power On/Off of the TV.
To adjust volume. You can also adjust volume with the volume buttons on remote control.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
To show Power On/Off.
Refer to ‘Real data mapping 1 ’. See page 112.
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
* If there is the time delay between command and ack message during power on sequence, It should be described like “Note: In this model, TV will send the Acknowledge after power on processing com- pletion. There might be a time delay between com- mand and acknowledge.”
To adjust screen contrast. You can also adjust contrast in the Picture menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Refer to ‘Real data mapping 1’. See page 112.
To adjust the screen format. (Main picture format) You can adjust the screen format using the Aspect Ratio in the Picture menu.
Acknowledgement [g][ ][Set ID][ ][OK][Data][x]
Transmission [k][c][ ][Set ID][ ][Data][Cr]
To adjust screen brightness. You can also adjust brightness in the Picture menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
Data Min : 00 ~ Max : 64 Refer to ‘Real data mapping 1’. See page 112.
* Using the RGB-PC, Component or HDMI input, you select either 16:9 or 4:3 screen aspect ratio. * In HDMI/Component (over 720p) mode, Just Scan is available.
Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
To adjust the screen colour. You can also adjust colour in the Picture menu.
To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Refer to ‘Real data mapping 1’. See page 112.
Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
To control volume mute on/off. You can also adjust mute using the MUTE button on remote control.
To adjust the screen tint. You can also adjust tint in the Picture menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Refer to ‘Real data mapping 1’. See page 112.
Acknowledgement [j][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]

To adjust the screen sharpness.
To adjust balance.
You can also adjust sharpness in the Picture menu.
You can also adjust balance in the Audio menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Refer to ‘Real data mapping 1’. See page 112.
Refer to ‘Real data mapping 1’. See page 112.
Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]
To select OSD (On Screen Display) on/off when controlling remotely.
To adjust colour temperature.
You can also adjust Colour Temperature in the Picture menu.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Transmission [k][u][ ][Set ID][ ][Data][Cr]
Acknowledgement [l][ ][Set ID][ ][OK][Data][x]
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
To lock the remote control and the front panel
controls on the set.
To adjust red in colour temperature.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Transmission [k][v][ ][Set ID][ ][Data][Cr]
Refer to ‘Real data mapping 2’. See page 112.
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
To control the PIP (Picture In picture)/DW.
You can also control the PIP/DW using the PIP button on the remote control or in the PIP/DW menu.
To adjust green in colour temperature.
Transmission [k][n][ ][Set ID][ ][Data][Cr]
Transmission [k][w][ ][Set ID][ ][Data][Cr]
Data 00:PIP/DW off Data 01: PIP Data 02: DW1 Data 03: DW2
Refer to ‘Real data mapping 2’. See page 112.
Acknowledgement [n][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [w][ ][Set ID][ ][OK/NG][Data][x]
To select sub picture position for PIP.
You can also adjust the sub picture position using
To adjust blue in colour temperature.
PIP button on the remote control or in the PIP/DW menu.
Transmission [k][$][ ][Set ID][ ][Data][Cr]
Transmission [k][q][ ][Set ID][ ][Data][Cr]
Data 00: Right down on screen Data 01: Left down on screen Data 02: Left up on screen Data 03: Right up on screen
Refer to ‘Real data mapping 2’. See page 112.
Acknowledgement [$][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]

To recognize an abnormal state.
To adjust picture position and minimize image
Transmission [k][z][ ][Set ID][ ][FF][ ][Cr]
shaking automatically. It works only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Acknowledgement [z][ ][Set ID][ ][OK/NG][Data][x]
Data 00: Normal (Power on and signal exist) Data 01: No signal (Power on) Data 02: Turn the TV off by remote control Data 03: Turn the TV off by sleep time function Data 04: Turn the TV off by RS-232C function Data 05: 5V down Data 06: AC down Data 07: Turn the TV off by Fan Alarm function (option) Data 08: Turn the TV off by Off time function Data 09: Turn the TV off by Auto off function Data a: Turn the TV off by AV board detection. * This function is “read only”.
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
G To adjust equalize.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
0
4 3 2 1 0
To avoid having a fixed image remain on screen.
0
Transmission [j][p][ ][Set ID][ ][Data][Cr]
0 1
0 0 0 1 0
0
Reserved Inversion Orbiter White Wash Normal
1 0
31(decimal) 7 6 5 4 3 2 1 0 Function
1 1 1 8’th Band
1
0 0 0 1 Inversion
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
0 0 1 0 Orbiter
0 1 0 0 White wash
1 0 0 0 Normal
* Real data mapping 1
* Real data mapping 2
x Reserved
*More two kinds of function can not be set at a time.
Acknowledgement [p][ ][Set ID][ ][OK/NG][Data][x]
To reduce the power consumption of the TV.
Transmission [j][q][ ][Set ID][ ][Data][ ][Cr]
Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]

Tune Channel to following Physical/major/minor number
(Main Picture Input) To select input source for TV.
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1]
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data 0: Min: 00H ~ Max: 63H (* transmit by Hexadecimal code) Data 1: Don’t care Data 2: 0 : Main
0
External Input Input Number
Acknowledgement [a][ ][Set ID][ ][OK][Data0][Data1][x]
[a][ ][Set ID][ ][NG][Data0][x]
0 0 0 1 Analog
0 1 0 0 Component
G To set skip status for the current Programme.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
0 Input1
0 0 0 1 Input2
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
0 0 1 0 Input3
0 0 1 1 Input4
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
To send IR remote key code.
To adjust input source for sub picture in PIP mode
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Transmission [x][y][ ][Set ID][ ][Data][Cr]
Data: Key code - Refer to page 106.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
0
External Input Input Number
0 0 0 1 Analog
0 Input1
0 0 0 1 Input2
0 0 1 0 Input3
0 0 1 1 Input4
Acknowledgement [y][ ][Set ID][ ][OK/NG][Data][x]


Pages referenced in this manual — manufacturer, support and downloads.
Common problems, likely causes, and what to do.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.