EN
LG logo
Official user manual

LG Electronics 47LA71**

128 pages·11.8 MB·Flat Panel Television·PDF·ENDEFRITNLJA
LG Electronics 47LA71**
Table of Contents 1 sections #EV# ShowHide
Page 1 of the LG Electronics 47LA71** user manual — Printed in Korea P/NO : MFL67727101(1311-REV01)
Page 1 · click to enlarge
Page 1
LG Electronics 47LA71** diagram (page 1)
Fig. 1

Internal Use Only

North/Latin America http://aic.lgservice.com Europe/Africa http://eic.lgservice.com Asia/Oceania http://biz.lgservice.com

LED TV SERVICE MANUAL

CHASSIS : LD33B MODEL : 47LA66** 47LA66**-Z*

47LA71** 47LA71**-ZA

LG Electronics 47LA71** — Internal Use Only diagram (page 1)
Fig. 2 · Internal Use Only
LG Electronics 47LA71** — Internal Use Only diagram (page 1)
Fig. 3 · Internal Use Only

Printed in Korea P/NO : MFL67727101(1311-REV01)

Page 2 of the LG Electronics 47LA71** user manual — CONTENTS
Page 2 · click to enlarge
Page 2

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ......................................................................... 3

SERVICING PRECAUTIONS.................................................................... 4

SPECIFICATION........................................................................................ 6

ADJUSTMENT INSTRUCTION............................................................... 14

BLOCK DIAGRAM ................................................................................. 21

EXPLODED VIEW .................................................................................. 22

SCHEMATIC CIRCUIT DIAGRAM

- 2 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 3 of the LG Electronics 47LA71** user manual — Before returning the receiver to the customer,
Page 3 · click to enlarge
Page 3

SAFETY PRECAUTIONS

LG Electronics 47LA71** — SAFETY PRECAUTIONS diagram (page 3)
Fig. 4

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5 mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB.

Leakage Current Hot Check circuit

Keep wires away from high voltage or high temperature parts.

LG Electronics 47LA71** — Leakage Current Hot Check circuit diagram (page 3)
Fig. 5 · Leakage Current Hot Check circuit

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check) With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 MΩ and 5.2 MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

- 3 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 4 of the LG Electronics 47LA71** user manual — a. Removing or reinstalling any component, circuit board mod
Page 4 · click to enlarge
Page 4

SERVICING PRECAUTIONS

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or expo sure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as “anti-static” can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electri cally shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replace ment ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity suf ficient to damage an ES device.)

General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before;

a. Removing or reinstalling any component, circuit board mod

ule or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection. c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explo sion hazard. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.

General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 °F to 600 °F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire- bristle (0.5 inch, or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature.

(500 °F to 600 °F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuit board printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged eas ily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component dam age caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alter natively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent poten tial shock reasons prior to applying power to the unit under test.

(500 °F to 600 °F) b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the compo nent lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

- 4 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 5 of the LG Electronics 47LA71** user manual
Page 5 · click to enlarge
Page 5

IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the cir cuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connec tions).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

"Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly con nected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as pos sible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top.

- 5 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 6 of the LG Electronics 47LA71** user manual
Page 6 · click to enlarge
Page 6

SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement.

1. Application range This specification is applied to the LCD TV used LD33B chassis.
3. Test method 1) Performance: LGE TV test method followed 2) Demanded other specification - Safety : CE, IEC specification - EMC : CE, IEC
2. Requirement for Test Each part is tested as below without special appointment.

1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C 2) Relative Humidity: 65 % ± 10 % 3) Power Voltage : Standard input voltage (AC 100-240 V~, 50/60 Hz) * Standard Voltage of each products is marked by models. 4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM. 5) The receiver must be operated for about 20 minutes prior to the adjustment.

4. Model General Specification No.ItemSpecificationRemarks 1MarketEU(PAL Market-37Countries)DTV & Analog (Total 37 countries) DTV (MPEG2/4, DVB-T) : 29 countries Germany, Netherland, Switzerland, Hungary, Austria, Slov enia, Bulgaria, France, Spain, Italy, Belgium, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ireland, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus DTV (MPEG2/4, DVB-T2): 8 countries UK(Ireland), Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan, Russia DTV (MPEG2/4, DVB-C): 37 countries Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ire land, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus, UK, Sweden, Denmark, Finland, Norway, Ukraine, Kazakhstan DTV (MPEG2/4,DVB-S): 30 countries Germany, Netherland, Switzerland, Hungary, Austria, Slovenia, Bulgaria, France, Spain, Italy, Belgium, Russia, Luxemburg, Greece, Czech, Croatia, Turkey, Moroco, Ire land, Latvia, Estonia, Lithuania, Poland, Portugal, Romania, Albania, Bosnia, Serbia, Slovakia, Beralus Supported satellite : 22 satellites HISPASAT 1C/1D, ATLANTIC BIRD 2, NILESAT 101/102, ATLANTIC BIRD 3, AMOS 2/3, THOR 5/6, IRIUS 4, EUTELSAT-W3A, EUROBIRD 9A, EUTELSAT-W2A, HOTBIRD 6/8/9, EUTELSAT-SESAT, ASTRA 1L/H/M/ KR, ASTRA 3A/3B, BADR 4/6, ASTRA 2D, EUROBIRD 3, EUTELSAT-W7, HELLASSAT 2, EXPRESS AM1, TURK SAT 2A/3A, INTERSAT10

- 6 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 7 of the LG Electronics 47LA71** user manual
Page 7 · click to enlarge
Page 7
No.ItemSpecificationRemarks 2Broadcasting system1) PAL-BG 2) PAL-DK 3) PAL-I/I’ 4) SECAM-L/L', DK , BG, I 5) DVB-T 6) DVB-C 7) DVB-T2 8) DVB-S/S2Model : *L*V*-Z* (T2 only Model) DVB-S: Satellite 3Program coverage1 ) Digital TV - VHF, UHF - C-Band,Ku-Band 2) Analogue TV - VHF : E2 to E12 - UHF : E21 to E69 - CATV : S1 to S20 - HYPER : S21 to S47 4Receiving systemAnalog : Upper Heterodyne Digital : COFDM, QAM► DVB-T - Guard Interval(Bitrate Mbit/s) _ 1/4, 1/8, 1/16, 1/32 - Modulation : Code Rate QPSK : 1/2, 2/3, 3/4, 5/6, 7/8 16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 ► DVB-T2 (Model : *L*V*-Z* (T2 only Model)) - Guard Interval(Bitrate Mbit/s) _ 1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256, - Modulation : Code Rate QPSK : 1/2, 2/5, 2/3, 3/4, 5/6 16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 ► DVB-C - Symbolrate : 4.0Msymbols/s to 7.2Msymbols/s - Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM ► DVB-S/S2 - symbolrate DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s DVB-S (QPSK) : 2 ~ 45Msymbol/s - viterbi DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8 DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10 5Scart (1EA)PAL, SECAMScart 1 Jack is Full scart and support ATV/DTV-OUT (not support DTV Auto AV) 6Video Input RCA(1EA)PAL, SECAM, NTSC4 System : PAL, SECAM, NTSC, PAL60 Common port 7Head phone outAntenna, AV1, AV2, Component, HDMI1, HDMI2, HDMI3, USB1, USB2, USB3 8Component Input (1EA)Y/Cb/Cr Y/Pb/PrHybrid Type 9HDMI Input (3EA)HDMI1-DTV HDMI2-DTV HDMI3-DTVHDMI1: PC support(HDMI version 1.3) Support HDCP 10Audio Input (3EA)DVI Audio Component/AV2 AV1L/R Input. 11SDPIF out (1EA)SPDIF out 12USB (1EA)EMF, DivX HD, For SVC (download)JPEG, MP3, DivX HD 13Ethernet Connect(1EA)Ethernet Connect

- 7 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 8 of the LG Electronics 47LA71** user manual
Page 8 · click to enlarge
Page 8
5. Component Video Input (Y, Pb, Pr) No.ResolutionH-freq(kHz)V-freq(Hz)Pixel clock 1.720×48015.7360.00SDTV, DVD 480i 2.720×48015.6359.94SDTV, DVD 480i 3.720×48031.4759.94480p 4.720×48031.5060.00480p 5.720×57615.62550.00SDTV 576i 6.720×57631.2550.00SDTV 576p 7.1280×72045.0050.00HDTV 720p 8.1280×72044.9659.94HDTV 720p 9.1280×72045.0060.00HDTV 720p 10.1920×108031.2550.00HDTV 1080i 11.1920×108033.7560.00HDTV 1080i 12.1920×108033.7259.94HDTV 1080i 13.1920×108056.25050HDTV 1080p 14.1920×108067.560HDTV 1080p
LG Electronics 47LA71** diagram (page 8)
Fig. 6

- 8 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 9 of the LG Electronics 47LA71** user manual
Page 9 · click to enlarge
Page 9
6. HDMI Input 6.1. DTV mode No.ResolutionH-freq(kHz)V-freq.(Hz)Pixel clock(MHz) 1.640*48031.469 / 31.559.94/60SDTV 480P 2.720*48031.469 / 31.559.94 / 60SDTV 480P 3.720*57631.2550SDTV 576P 4.720*57615.62550SDTV 576I 5.1280*72037.50050HDTV 720P 6.1280*72044.96 / 4559.94 / 60HDTV 720P 7.1920*108033.72 / 33.7559.94 / 60HDTV 1080I 8.1920*108028.12550.00HDTV 1080I 9.1920*108026.97 / 2723.97 / 24HDTV 1080P 10.1920*108025HDTV 1080P 11.1920*108033.716 / 33.7529.976 / 30.00HDTV 1080P 12.1920*108056.25050HDTV 1080P 13.1920*108067.43 / 67.559.94 / 60HDTV 1080P
LG Electronics 47LA71** diagram (page 9)
Fig. 7
6.2. PC mode No.ResolutionH-freq(kHz)V-freq.(Hz)Pixel clock(MHz) 1640 x 350 @70Hz31.46870.09EGA 2720 x 400 @70Hz31.46970.08DOS 3640 x 480 @60Hz31.46959.94VESA(VGA) 4800 x 600 @60Hz37.87960.31VESA(SVGA) 51024 x 768 @60Hz48.36360.00VESA(XGA) 61152 x 864 @60Hz54.34860.053VESA 71280 x 1024 @60Hz63.98160.020VESA(SXGA) 81360 x 768 @60Hz47.71260.015VESA(WXGA) 91920 x 1080 @60Hz67.560.00WUXGA(Reduced Blanking) 10.1920*108025HDTV 1080P 11.1920*108033.716 / 33.7529.976 / 30.00HDTV 1080P 12.1920*108056.25050HDTV 1080P 13.1920*108067.43 / 67.559.94 / 60HDTV 1080P
LG Electronics 47LA71** diagram (page 9)
Fig. 8

- 9 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 10 of the LG Electronics 47LA71** user manual
Page 10 · click to enlarge
Page 10
7. 3D Mode 7.1. HDMI 1.4b (3D supported mode automatically) No.ResolutionH-freq(kHz)V-freq.(Hz)Pixel clock(MHz)VIC3D input proposed modeProposed 1640*48031.469 / 31.559.94/ 6025.1251Top-and-Bottom Side-by-side(half)Secondary(SDTV 480P) Secondary(SDTV 480P) 262.938/6359.94/ 6050.35/50.41Frame packing Line alternativeSecondary(SDTV 480P) (SDTV 480P) 331.469 / 31.559.94/ 6050.35/50.41Side-by-side(Full)(SDTV 480P) 4720*48031.469 / 31.559.94 / 6027.00/27.032,3Top-and-Bottom Side-by-side(half)Secondary(SDTV 480P) Secondary(SDTV 480P) 562.938/6359.94 / 6054/54.062,3Frame packing Line alternativeSecondary(SDTV 480P) (SDTV 480P) 631.469 / 31.559.94 / 6054/54.062,3Side-by-side(Full)(SDTV 480P) 7720*57631.25502717,18Top-and-Bottom Side-by-side(half)Secondary(SDTV 576P) Secondary(SDTV 576P) 862.5505417,18Frame packing Line alternativeSecondary(SDTV 576P) (SDTV 576P) 931.25505417,18Side-by-side(Full)(SDTV 576P) 10720*57615.625502721Top-and-Bottom Side-by-side(half)Secondary(SDTV 576I) Secondary(SDTV 576I) 1131.25505421Frame packing Field alternativeSecondary(SDTV 576I) (SDTV 576I) 1215.625505421Side-by-side(Full)(SDTV 576I) 131280*72037.5005074.2519Top-and-Bottom Side-by-side(half)Primary(HDTV 720P) Primary(HDTV 720P) 147550148.519Frame packing Line alternativePrimary(HDTV 720P) (HDTV 720P) 1537.50050148.519Side-by-side(Full)(HDTV 720P) 1644.96 / 4559.94 / 6074.18/74.254Top-and-Bottom Side-by-side(half)Primary(HDTV 720P) Primary(HDTV 720P) 1789.91/9059.94 / 60148.35/148.54Frame packing Line alternativePrimary(HDTV 720P) (HDTV 720P) 1844.96 / 4559.94 / 60148.35/148.54Side-by-side(Full)(HDTV 720P) 191920*108033.72 / 33.7559.94 / 6074.18/74.255Top-and-Bottom Side-by-side(half)Secondary(HDTV 1080I) Primary(HDTV 1080I) 2067.432 / 67.5059.94 / 60148.35/148.55Frame packing Field alternativePrimary(HDTV 1080I) (HDTV 1080I) 2133.72 / 33.7559.94 / 60148.35/148.55Side-by-side(Full)(HDTV 1080I) 2228.12550.0074.2520Top-and-Bottom Side-by-side(half)Secondary(HDTV 1080I) Primary(HDTV 1080I) 2356.2550.00148.520Frame packing Field alternativePrimary(HDTV 1080I) (HDTV 1080I) 2428.12550.00148.520Side-by-side(Full)(HDTV 1080I) 251920*108026.97 / 2723.97 / 2474.18/74.2532Top-and-Bottom Side-by-side(half)Primary(HDTV 1080P) Primary(HDTV 1080P) 2643.94/5423.97 / 24148.35/148.532Frame packing Line alternativePrimary(HDTV 1080P) (HDTV 1080P) 2726.97 / 2723.97 / 24148.35/148.532Side-by-side(Full)(HDTV 1080P) 2828.1252574.2533Top-and-Bottom Side-by-side(half)Secondary(HDTV 1080P) Secondary(HDTV 1080P) 2956.2425148.533Frame packing Line alternativeSecondary(HDTV 1080P) (HDTV 1080P) 3028.1225148.533Side-by-side(Full)(HDTV 1080P) 3133.716 / 33.7529.976 / 30.0074.18/74.2534Top-and-Bottom Side-by-side(half)Primary(HDTV 1080P) Secondary(HDTV 1080P) 3267.432 / 67.529.976 / 30.00148.35/148.534Frame packing Line alternativePrimary(HDTV 1080P) (HDTV 1080P) 3333.716 / 33.7529.976 / 30.00148.35/148.534Side-by-side(Full)(HDTV 1080P) 3456.25050148.531Top-and-Bottom Side-by-side(half)Primary(HDTV 1080P) Secondary(HDTV 1080P) 3567.43 / 67.559.94 / 60148.35/148.5016Top-and-Bottom Side-by-side(half)Primary(HDTV 1080P) Secondary(HDTV 1080P)

- 10 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 11 of the LG Electronics 47LA71** user manual
Page 11 · click to enlarge
Page 11
7.2. HDMI Input(1.3) No.ResolutionH-freq(kHz)V-freq.(kHz)Pixel clock(MHz)Proposed3D input proposed mode 11280*72045.0060.0074.25HDTV 720P2D to 3D, Side by Side(half), Top & Bottom, Single Frame Sequential 21280*72037.5005074.25HDTV 720P 31920*108033.7560.0074.25HDTV 1080I2D to 3D, Side by Side(half), Top & Bottom 41920*108028.12550.0074.25HDTV 1080I 51920*108027.0024.0074.25HDTV 1080P2D to 3D, Side by Side(Half), Top & Bottom, Checker Board 61920*108028.122574.25HDTV 1080P 71920*108033.7530.0074.25HDTV 1080P 81920*108067.5060.00148.5HDTV 1080P2D to 3D, Side by Side(half), Top & Bottom, Checkerboard, Single Frame Sequential, Row Interleaving, Column Interleaving 91920*108056.2550148.5HDTV 1080P
7.3. RF Input(3D supported mode manually) No.ResolutionProposed3D input proposed mode 1HD1080I 720P2D to 3D Side by Side(Half) Top & Bottom 2SD576P 576I2D to 3D
LG Electronics 47LA71** diagram (page 11)
Fig. 9
7.4. RF Input (3D supported mode automatically) No.Signal3D input proposed mode 1Frame CompatibleSide by Side(Half), Top & Bottom
LG Electronics 47LA71** diagram (page 11)
Fig. 10
7.5. USB Input (3D supported mode manually) No.ResolutionH-freq(kHz)V-freq.(Hz)Pixel clock(MHz)Proposed3D input proposed mode 11920*108033.753074.25HDTV 1080P2D to 3D, Side by Side(Half)*, Top & Bottom*, Checkerboard*, Row Interleaving, Column Interleaving (Photo : side by Side(half), Top & Bottom) Others---640*350 720*400 640*480 800*600 1152*864 1280*10242D to 3D (“*” 3D supported mode manually & automatically)
LG Electronics 47LA71** diagram (page 11)
Fig. 11

- 11 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 12 of the LG Electronics 47LA71** user manual
Page 12 · click to enlarge
Page 12
7.6. HDMI-PC Input (3D supported mode manually) No.ResolutionH-freq(kHz)V-freq.(Hz)Pixel clock(MHz)3D input proposed modeProposed 11024*76848.3660652D to 3D, Side by Side(half) Top & BottomHDTV 768P 21360*76847.716085.52D to 3D, Side by Side(half) Top & BottomHDTV 768P 31920*108067.50060148.502D to 3D, Side by Side(half) Top & Bottom, Checker Board, Single Frame Sequential, Row Interleaving, Column InterleavingHDTV 1080P 4Others---2D to 3D640*350 720*400 640*480 800*600 1152*864
LG Electronics 47LA71** diagram (page 12)
Fig. 12
7.7. DLNA Input (3D supported mode manually) No.ResolutionH-freq(kHz)V-freq.(Hz)Pixel clock(MHz)Proposed3D input proposed mode 11920*108033.753074.252D to 3D, Side by Side(Half)*,Top & Bottom*,Checker Board*, Row Interleav ing, Column Interleaving(Photo : Side by Side(Half), Top&Bottom) (“*” 3D supported mode manually & automatically)
LG Electronics 47LA71** diagram (page 12)
Fig. 13
LG Electronics 47LA71** diagram (page 12)
Fig. 14
No.ResolutionH-freq(kHz)V-freq.(Hz)Pixel clockProposed3D input proposed mode 11280*72045.0060.0074.25HDTV 720P2D to 3D, Side by Side(Half), Top & Bottom 21280*72037.5005074.25HDTV 720P 31920*108033.7560.0074.25HDTV 1080I 41920*108028.12550.0074.25HDTV 1080I 51920*108027.0024.0074.25HDTV 1080P 61920*108028.122574.25HDTV 1080P 71920*108033.7530.0074.25HDTV 1080P 81920*108067.5060.00148.5HDTV 1080P 91920*108056.25050148.5HDTV 1080P
7.9. 3D Input mode No.Side by SideTop & BottomChecker boardSingle Frame SequentialFrame Packing2D to 3D 1ii.iii.iv.v.vi.
LG Electronics 47LA71** diagram (page 12)
Fig. 15

- 12 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 13 of the LG Electronics 47LA71** user manual —
Page 13 · click to enlarge
Page 13

ADJUSTMENT INSTRUCTION

1. Application Range This specification sheet is applied to all of the LED LCD TV with LD33B chassis.

3.2. LAN Inspection 3.2.1. Equipment & Condition ▪ Each other connection to LAN Port of IP Hub and Jig

LG Electronics 47LA71** — ADJUSTMENT INSTRUCTION diagram (page 13)
Fig. 16
2. Designation (1) Because this is not a hot chassis, it is not necessary to

use an isolation transformer. However, the use of isolation transformer will help protect test instrument. (2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of

25 °C ± 5 °C of temperature and 65 % ± 10 % of relative humidity if there is no specific designation. (4) The input voltage of the receiver must keep AC 100-240

  • 3.2.2. LAN inspection solution
  • LAN Port connection with PCB
  • Setting automatic IP

V~, 50/60 Hz. (5) The receiver must be operated for about 5 minutes prior to

LG Electronics 47LA71** — ADJUSTMENT INSTRUCTION diagram (page 13)
Fig. 17

the adjustment when module is in the circumstance of over 15.

In case of keeping module is in the circumstance of 0 °C, it should be placed in the circumstance of above 15 °C for 2 hours.

LG Electronics 47LA71** — ADJUSTMENT INSTRUCTION diagram (page 13)
Fig. 18

In case of keeping module is in the circumstance of below -20 °C, it should be placed in the circumstance of above 15 °C for 3 hours.

  • If you want manual connection, enter Network connection at

MENU Mode of TV. Press Start connection key, then Network will be connected.

[Caution] When still image is displayed for a period of 20 minutes or longer (Especially where W/B scale is strong. Digital pattern 13ch and/or Cross hatch pattern 09ch), there can some afterimage in the black level area.

LG Electronics 47LA71** — ADJUSTMENT INSTRUCTION diagram (page 13)
Fig. 19
  • 3. Automatic Adjustment 3.1. MAC address D/L, CI+ key D/L, Widevine key D/L, ESN D/L, HDCP14/20 D/L Connect: USB port Communication Prot connection
  • Com 1,2,3,4 and 115200(Baudrate) Mode check: Online Only
  • Check the test process: DETECT -> MAC -> CI -> Widevine
  • Setting state confirmation

- If automatic setting is finished, you confirm IP and MAC

  • -> ESN -> HDCP14 -> HDCP20
  • Play: Press Enter key
  • Result: Ready, Test, OK or NG
  • Printer Out (MAC Address Label)

Address at ‘in start’ menu mode.

LG Electronics 47LA71** —  diagram (page 13)
Fig. 20
LG Electronics 47LA71** —  diagram (page 13)
Fig. 21

- 13 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 14 of the LG Electronics 47LA71** user manual — *IP Number : 12.12.2.2
Page 14 · click to enlarge
Page 14

3.2.3. WIDEVINE key Inspection - Confirm key input data at the "IN START" MENU Mode.

3.4. Model name & Serial number Download 3.4.1. Model name & Serial number D/L

  • Press "P-ONLY" key of service remote control.

(Baud rate : 115200 bps)

  • Connect RS-232C Signal to USB Cable to USB.
  • Write Serial number by use USB port.
  • Must check the serial number at Instart menu.

3.4.2. Method & notice (1) Serial number D/L is using of scan equipment. (2) Setting of scan equipment operated by Manufacturing

Technology Group. (3) Serial number D/L must be conformed when it is produced

in production line, because serial number D/L is mandatory by D-book 4.0.

* Manual Download (Model Name and Serial Number) If the TV set is downloaded by OTA or service man, sometimes model name or serial number is initialized.(Not always) It is impossible to download by bar code scan, so It need Manual download. 1) Press the "Instart" key of Adjustment remote control. 2) Go to the menu "7.Model Number D/L" like below photo. 3) Input the Factory model name(ex 42LA690V-ZA) or Serial number like photo.

3.3. LAN PORT INSPECTION(PING TEST) Connect SET → LAN port == PC → LAN Port

SET PC

3.3.1. Equipment setting (1) Play the LAN Port Test PROGRAM. (2) Input IP set up for an inspection to Test Program.

LG Electronics 47LA71** — SET PC diagram (page 14)
Fig. 22

*IP Number : 12.12.2.2

3.3.2. LAN PORT inspection(PING TEST) (1) Play the LAN Port Test Program. (2) Connect each other LAN Port Jack. (3) Play Test (F9) button and confirm OK Message. (4) Remove LAN cable.

LG Electronics 47LA71** — *IP Number : 12.12.2.2 diagram (page 14)
Fig. 23 · *IP Number : 12.12.2.2
4. Check the model name Instart menu. → Factory name displayed. (ex 42LA690V-ZA) 5) Check the Diagnostics.(DTV country only) → Buyer model displayed. (ex 42LA690V-ZA)

3.5. CI+ Key checking method - Check the Section 3.1 Check whether the key was downloaded or not at ‘In Start’ menu. (Refer to below).

LG Electronics 47LA71** — *IP Number : 12.12.2.2 diagram (page 14)
Fig. 24 · *IP Number : 12.12.2.2

=> Check the Download to CI+ Key value in LGset.

- 14 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 15 of the LG Electronics 47LA71** user manual — ⓖ Colorimetry Data Block(HDMI)
Page 15 · click to enlarge
Page 15

3.5.1. Check the method of CI+ Key value (1) Check the method on Instart menu (2) Check the method of RS232C Command

4. Manual Adjustment * ADC adjustment is not needed because of OTP(Auto ADC adjustment)

1) Into the main ass’y mode(RS232: aa 00 00)

CMD 1 CMD 2 Data 0

4.1. EDID DATA 4.1.1. 3D EDID

A A 0 0

2) Check the key download for transmitted command (RS232: ci 00 10)

LG Electronics 47LA71** — 1) Into the main ass’y mode(RS232: aa 00 00) diagram (page 15)
Fig. 25 · 1) Into the main ass’y mode(RS232: aa 00 00)

CMD 1 CMD 2 Data 0

C I 1 0

3. Result value - Normally status for download : OKx - Abnormally status for download : NGx

3.5.2. Check the method of CI+ key value(RS232) 1) Into the main ass’y mode(RS232: aa 00 00)

CMD 1 CMD 2 Data 0

  • Reference

A A 0 0

- HDMI1 ~ HDMI4 / RGB - In the data of EDID, bellows may be different by S/W or

2. Check the mothed of CI+ key by command (RS232: ci 00 20)

Input mode. ⓐ Product ID

CMD 1 CMD 2 Data 0

HEX EDID Table DDC Function 0001 0100 Analog 0001 0100 Digital

C I 2 0

3) Result value i 01 OK 1d1852d21c1ed5dcx

ⓑ Serial NoControlled on production line. ⓒ Month, Year: Controlled on production line:

CI+ Key Value

ex) Monthly‘01’ → ‘01’ Year : ‘2013’ → ‘17’ ⓓ Model Name(Hex): LGTV

3.6. WIFI MAC ADDRESS CHECK (1) Using RS232 Command

Chassis MODEL NAME(HEX)

H-freq(kHz) V-freq.(Hz)

LD33B 00 00 00 FC 00 4C 47 20 54 56 0A 20

Transmission [A][I][][Set ID][][20][Cr] [O][K][X] or [NG]

ⓔ Checksum(LG TV): Changeable by total EDID data.

ⓔ 1 ⓔ 2 ⓔ 2 ⓔ 3 10bit /none XvYcc

(2) Check the menu on in-start

8bit /none XvYcc HDMI1 E8 85 CC X HDMI2 E8 75 BC X HDMI3 E8 65 AC X

LG Electronics 47LA71** — ⓔ 1 ⓔ 2 ⓔ 2 ⓔ 3 10bit /none XvYcc diagram (page 15)
Fig. 26 · ⓔ 1 ⓔ 2 ⓔ 2 ⓔ 3 10bit /none XvYcc

ⓕ Vendor Specific(HDMI)

1) Deep color (module 10bit)

INPUT MODEL NAME(HEX)

HDMI1 78 03 0C 00 10 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI2 78 03 0C 00 20 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI3 78 03 0C 00 30 00 B8 2D 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

2) None deep color (module 8bit)

INPUT MODEL NAME(HEX)

HDMI1 78 03 0C 00 10 00 80 1E 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI2 78 03 0C 00 20 00 80 1E 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

HDMI3 78 03 0C 00 30 00 80 1E 20 C0 0E 01 4F 3F FC 08 10 18 10 06 10 16 10 28 10

ⓖ Colorimetry Data Block(HDMI)

1) The Model not supporting XvYcc

INPUT MODEL NAME(HEX) HDMI1 E3 05 00 00 HDMI2 E3 05 00 00 HDMI3 E3 05 00 00

- 15 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 16 of the LG Electronics 47LA71** user manual — G Cut
Page 16 · click to enlarge
Page 16

4.1.2. 2D EDID

4.2.3. Equipment connection MAP

LG Electronics 47LA71** — 4.1.2. 2D EDID diagram (page 16)
Fig. 27

Color Analyzer

RS-232C

Computer

RS-232C

RS-232C

Pattern Generator

Signal Source

* If TV internal pattern is used, not needed

  • Reference

4.2.4. Adj. Command (Protocol) <Command Format>

- HDMI1 ~ HDMI4 / RGB - In the data of EDID, bellows may be different by S/W or

START 6E A 50 A LEN A 03 A CMD A 00 A VAL A CS STOP

Input mode. ⓐ Product ID

- LEN: Number of Data Byte to be sent - CMD: Command - VAL: FOS Data value - CS: Checksum of sent data - A: Acknowledge Ex) [Send: JA_00_DD] / [Ack: A_00_okDDX]

HEX EDID Table DDC Function 0001 0100 Analog 0001 0100 Digital

ⓑ Serial NoControlled on production line. ⓒ Month, Year: Controlled on production line:
  • RS-232C Command used during auto-adjustment.
ex) Monthly‘01’ → ‘01’ Year : ‘2012’ → ‘16’ ⓓ Model Name(Hex): LGTV

RS-232C COMMAND [CMD ID DATA] Explantion

wb 00 00 Begin White Balance adjustment

Chassis MODEL NAME(HEX) LD33B 00 00 00 FC 00 4C 47 20 54 56 0A 20

wb 00 10 Gain adjustment(internal white pattern)

wb 00 1f Gain adjustment completed

wb 00 20 Offset adjustment(internal white pattern)

ⓔ Checksum(LG TV): Changeable by total EDID data.

wb 00 2f Offset adjustment completed

ⓔ1 ⓔ2 ⓔ3 HDMI1 43 15 X HDMI2 43 05 X HDMI3 43 F5 X

wb 00 ff End White Balance adjustment (internal pattern disappears )

Ex) wb 00 00 -> Begin white balance auto-adj.

wb 00 10 -> Gain adj. ja 00 ff -> Adj. data jb 00 c0 wb 00 1f → Gain adj. completed *(wb 00 20(Start), wb 00 2f(end)) → Off-set adj. wb 00 ff → End white balance auto-adj.

ⓕ Vendor Specific(HDMI)

INPUT MODEL NAME(HEX) HDMI1 67 03 0C 00 10 00 80 2D HDMI2 67 03 0C 00 20 00 80 2D HDMI3 67 03 0C 00 30 00 80 2D

4.2. White Balance Adjustment 4.2.1. Overview ▪ W/B adj. Objective & How-it-works

  • Adj. Map Applied Model : LD33B Chassis ALL MODELS

(1) Objective: To reduce each Panel's W/B deviation (2) How-it-works : When R/G/B gain in the OSD is at 192, it

Adj. item Command (lower caseASCII)

Default (Decimal) CMD1 CMD2 MIN MAX

Data Range

(Hex.)

means the panel is at its Full Dynamic Range. In order to prevent saturation of Full Dynamic range and data, one of R/G/B is fixed at 192, and the other two is lowered to find the desired value. (3) Adjustment condition : normal temperature

R Gain j g 00 C0 G Gain j h 00 C0 B Gain j i 00 C0 R Cut G Cut B Cut

Cool

1. Surrounding Temperature : 25 °C ± 5 °C 2) Surrounding Humidity : 20 % ~ 80 %

R Gain j a 00 C0 G Gain j b 00 C0 B Gain j c 00 C0 R Cut G Cut B Cut

4.2.2. Equipment (1) Color AnalyzerCA-210 (LED Module : CH 14) (2) Adjustment Computer(During auto adj., RS-232C protocol

Medium

is needed) (3) Adjustment Remote control (4) Video Signal Generator MSPG-925F 720p/216-Gray

R Gain j d 00 C0 G Gain j e 00 C0 B Gain j f 00 C0 R Cut

Warm

(Model: 217, Pattern: 78) → Only when internal pattern is not available ▪ Color Analyzer Matrix should be calibrated using CS-1000.

G Cut

- 16 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Probe

Page 17 of the LG Electronics 47LA71** user manual — Mode Coordinate Temp ∆uv x y
Page 17 · click to enlarge
Page 17

4.2.5. Adj. method (1) Auto adj. method

  • Standard color coordinate and temperature using CA-210(CH 14)

Mode Coordinate Temp ∆uv x y

1. Set TV in adj. mode using POWER ON key. 2) Zero calibrate probe then place it on the center of the Display. 3) Connect Cable.(RS-232C to USB) 4) Select mode in adj. Program and begin adj. 5) When adj. is complete (OK Sign), check adj. status pre mode. (Warm, Medium, Cool) 6) Remove probe and RS-232C cable to complete adj. ▪ W/B Adj. must begin as start command “wb 00 00” , and

Cool 0.269 ± 0.002 0.273 ± 0.002 13000 K 0.0000

Medium 0.285 ± 0.002 0.293 ± 0.002 9300 K 0.0000

Warm 0.313 ± 0.002 0.329 ± 0.002 6500K 0.0000

4.2.7. ALELF & EDGE LED White balance table - EDGE LED module change color coordinate because of

finish as end command “wb 00 ff”, and Adj. offset if need.

aging time. - Apply under the color coordinate table, for compensated

(2) Manual adjustment. method

aging time. * Normal Line [LN5xxx, LA6xxx, LA7xxx, LA8xxx]

1. Set TV in Adj. mode using POWER ON. 2) Zero Calibrate the probe of Color Analyzer, then place it on the center of LCD module within 10 cm of the surface. 3) Press ADJ key → EZ adjust using adj. R/C → 7. WhiteBalance then press the cursor to the right(key ►).

Cool Medium Warm X y x y x y 271 270 286 289 313 329 1 0-2 283 287 298 306 322 342 2 3-5 282 285 297 304 321 340 3 6-9 281 284 296 303 320 339 4 10-19 279 281 294 300 318 336 5 20-35 277 277 292 296 316 332 6 36-49 275 274 290 293 314 329 7 50-79 273 272 288 291 312 327 8 80-119 272 271 287 290 311 326 9 Over 120 271 270 286 289 310 325

Aging

NC4.0

time (Min)

(When right key(►) is pressed 204 Gray internal pattern will be displayed) 4) One of R Gain / G Gain / B Gain should be fixed at 192, and the rest will be lowered to meet the desired value. 5) Adjustment is performed in COOL, MEDIUM, WARM 3 modes of color temperature. ▪ If internal pattern is not available, use RF input. In EZ

Adj. menu 7.White Balance, you can select one of 2 Test-pattern: ON, OFF. Default is inner(ON). By selecting OFF, you can adjust using RF signal in 204 Gray pattern.

  • Adjustment condition and cautionary items

*Aging Chamber [LN5xxx, LA6xxx, LA7xxx, LA8xxx]

1. Lighting condition in surrounding area Surrounding lighting should be lower 10 lux. Try to isolate adj. area into dark surrounding. 2) Probe location : Color Analyzer(CA-210) probe should be within 10 cm

Cool Medium Warm X y x y x y 271 270 286 289 313 329 1 0-5 282 285 297 304 321 340 2 6-10 278 280 293 299 317 335 3 11-20 275 275 290 294 314 330 4 21-30 272 272 287 291 311 327 5 31-40 269 269 284 288 308 324 6 41-50 268 267 283 286 307 322 7 51-80 267 266 282 285 306 321 8 81-119 266 264 281 283 305 319 9 Over 120 265 263 280 282 304 318

Aging

NC4.0

time (Min)

and perpendicular of the module surface (80° ~ 100°) 3) Aging time - After Aging Start, Keep the Power ON status during 5

Minutes. - In case of LCD, Back-light on should be checked

using no signal or Full-white pattern.

  • 4.2.6. Reference (White balance Adj. coordinate and color temperature)
  • Luminance : 204 Gray
  • Standard color coordinate and temperature using CS-1000 (over 26 inch)

Mode Coordinate Temp ∆uv x y

Cool 0.269 0.273 13000 K 0.0000

Medium 0.285 0.293 9300 K 0.0000

Warm 0.313 0.329 6500 K 0.0000

- 17 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 18 of the LG Electronics 47LA71** user manual — through the AP/Magic Remocon Equipment on the line
Page 18 · click to enlarge
Page 18

4.3. Local Dimming Function Check Step 1) Turn on TV. Step 2) At the Local Dimming mode, module Edge Backlight

(2) When 3D OSD appear automatically, then select OK key.

moving right to left Back light of IOP module moving. Step 3) Confirm the Local Dimming mode. Step 4) Press "exit" key.

LG Electronics 47LA71** diagram (page 18)
Fig. 28

(3) Don't wear a 3D Glasses, check the picture like below.

LG Electronics 47LA71** diagram (page 18)
Fig. 29

4.6. Wi-Fi Test Step 1) Turn on TV Step 2) Select Network Connection option in Network Menu.

4.4. Magic Motion Remote control test - Results are automatically marked in Instart OSD after

through the AP/Magic Remocon Equipment on the line

LG Electronics 47LA71** — through the AP/Magic Remocon Equipment on the line diagram (page 18)
Fig. 30 · through the AP/Magic Remocon Equipment on the line
LG Electronics 47LA71** — through the AP/Magic Remocon Equipment on the line diagram (page 18)
Fig. 31 · through the AP/Magic Remocon Equipment on the line
LG Electronics 47LA71** — through the AP/Magic Remocon Equipment on the line diagram (page 18)
Fig. 32 · through the AP/Magic Remocon Equipment on the line
3. Select Start Connection button in Network Connection.
LG Electronics 47LA71** — through the AP/Magic Remocon Equipment on the line diagram (page 18)
Fig. 33 · through the AP/Magic Remocon Equipment on the line
4. If the system finds any AP like blow PIC, it is working

well.

4.5. 3D function test (Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4]) * HDMI mode NO. 872 , pattern No.83 (1) Please input 3D test pattern like below.

LG Electronics 47LA71** — through the AP/Magic Remocon Equipment on the line diagram (page 18)
Fig. 34 · through the AP/Magic Remocon Equipment on the line
LG Electronics 47LA71** — through the AP/Magic Remocon Equipment on the line diagram (page 18)
Fig. 35 · through the AP/Magic Remocon Equipment on the line

- 18 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 19 of the LG Electronics 47LA71** user manual — EQ Off AVL Off Clear Voice Off
Page 19 · click to enlarge
Page 19

4.7. LNB voltage and 22KHz tone check (only for DVB-S/S2 model) ▪ Test method

7. GND and Internal Pressure check 7.1. Method (1) GND & Internal Pressure auto-check preparation

(1) Set TV in Adj. mode using POWER ON. (2) Connect cable between satellite ANT and test JIG. (3) Press Yellow key(ETC+SWAP) in Adj Remote control to

- Check that Power cord is fully inserted to the SET. (If loose, re-insert) (2) Perform GND & Internal Pressure auto-check

make LNB on. (4) Check LED light ‘ON’ at 18 V menu. (5) Check LED light ‘ON’ at 22 KHz tone menu. (6) Press Blue key(ETC+PIP INPUT) in Adj Remote control

- Unit fully inserted Power cord, Antenna cable and A/V

arrive to the auto-check process. - Connect D-terminal to AV JACK TESTER - Auto CONTROLLER(GWS103-4) ON - Perform GND TEST - If NG, Buzzer will sound to inform the operator. - If OK, changeover to I/P check automatically.

to make LNB off. (7) Check LED light ‘OFF’ at 18 V menu. (8) Check LED light ‘OFF’ at 22 KHz tone menu.

(Remove CORD, A/V form AV JACK BOX.) - Perform I/P test - If NG, Buzzer will sound to inform the operator. - If OK, Good lamp will lit up and the stopper will allow the

  • Test result

(1) After press LNB On key, ‘18 V LED’ and ‘22 KHz tone

LED’ should be ON. (2) After press LNB OFF key, ‘18 V LED’ and ‘22 KHz tone

LED’ should be OFF.

pallet to move on to next process.

4.8. Option selection per country 4.8.1. Overview - Option selection is only done for models in Non-EU

7.2. Checkpoint ▪ TEST voltage

  • - GND: 1.5 KV / min at 100 mA - SIGNAL: 3 KV / min at 100 mA
  • TEST time: 1 second
  • TEST POINT

4.8.2. Method (1) Press ADJ key on the Adj. R/C, then select Country Group

Meun (2) Depending on destination, select Country Group Code 04

- GND TEST = POWER CORD GND & SIGNAL CABLE

METAL GND - Internal Pressure TEST = POWER CORD GND & LIVE &

or Country Group EU then on the lower Country option, select US, CA, MX. Selection is done using +, - or ►◄ key.

NEUTRAL ▪ LEAKAGE CURRENT: At 0.5 mArms

5. Tool Option selection ▪ Method : Press "ADJ" key on the Adjustment remote control,
8. Audio Measurement condition: (1) RF input: Mono, 1 KHz sine wave signal, 100 % Modulation (2) CVBS, Component: 1 KHz sine wave signal 0.5 Vrms (3) RGB PC: 1 KHz sine wave signal 0.7 Vrms

then select Tool option.

6. Ship-out mode check(In-stop) ▪ After final inspection, press "IN-STOP" key of the Adjustment

No. Item Min Typ Max Unit Remark

Audio practical max Output, L/R (Distortion=10% max Output)

9 10 12 W

remote control and check that the unit goes to Stand-by mode.

EQ Off AVL Off Clear Voice Off

8.10 10.8 Vrms

2. Speaker (8Ω Impedance) 9 10 12 W

- 19 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 20 of the LG Electronics 47LA71** user manual — - If your downloaded program version in USB Stick is
Page 20 · click to enlarge
Page 20
9. USB S/W Download(Service only) (1) Put the USB Stick to the USB socket (2) Automatically detecting update file in USB Stick

- If your downloaded program version in USB Stick is

Lower, it didn’t work. But your downloaded version is Higher, USB data is automatically detecting (Download Version High & Power only mode, Set is automatically Download) (3) Show the message “Do not unplug!”

LG Electronics 47LA71** — - If your downloaded program version in USB Stick is diagram (page 20)
Fig. 36 · - If your downloaded program version in USB Stick i…

(4) Updating is starting.

LG Electronics 47LA71** — - If your downloaded program version in USB Stick is diagram (page 20)
Fig. 37 · - If your downloaded program version in USB Stick i…
LG Electronics 47LA71** — - If your downloaded program version in USB Stick is diagram (page 20)
Fig. 38 · - If your downloaded program version in USB Stick i…

(5) Updating Completed, The TV will restart automatically (6) If your TV is turned on, check your updated version and

Tool option. (explain the Tool option, next stage) * If downloading version is more high than your TV have, TV can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didn’t have a DTV/ATV test on production line.

* After downloading, have to adjust Tool Option again. (1) Push "IN-START" key in service remote control. (2) Select "Tool Option 1" and push "OK" key. (3) Punch in the number. (Each model has their number)

- 20 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 21 of the LG Electronics 47LA71** user manual
Page 21 · click to enlarge
Page 21
LG Electronics 47LA71** diagram (page 21)
Fig. 39

- 21 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 22 of the LG Electronics 47LA71** user manual — * Set + Stand * Stand Base + Body
Page 22 · click to enlarge
Page 22
LG Electronics 47LA71** — #EV# diagram (page 22)
Fig. 40

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

* Set + Stand * Stand Base + Body

- 22 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 23 of the LG Electronics 47LA71** user manual — R131 4.7K
Page 23 · click to enlarge
Page 23
LG Electronics 47LA71** — #EV# diagram (page 23)
Fig. 41

ICE mode + 27M + ROM to eMMC boot from 1 0 1 1

ICE mode + 27M + serial boot 1 0 0 0

ICE mode + 27M + ROM to Nand boot 1 0 0 1

ICE mode + 27M + ROM to 60bit ECC Nand boot 1 0 1 0

ICE mode + 27M + ROM to eMMC 1 1 0 0

I2C_1 : AMP, L/DIMMING,HDCP KEY

I2C_6 : TUNER_MOPLL(T/C,ATV)

NON_TU_Q_KR

I2C_2 : T-CON,

R151

2.7K R141

I2C_3 : MICOM

I2C_5 : NVRAM

R149 4.7K

R148 4.7K

NVRAM_RENESAS

MTK_EPI

MTK_NON_EPI

R150

2.7K

R1EX24256BSAS0A

7 WP

6 SCL

5 SDA

+3.3V_NORMAL

R146 4.7K

R144 4.7K

IC100-*2

DDR_0.78G

NON_DDR_0.78G

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

R147

2.7K

Model Option

1 A0

2 A1

3 A2

4 VSS

I2C_SCL5

I2C_SDA5

R145 4.7K

R143 4.7K

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

- LowNormal Operation
- HighWrite Protection

MTK_DVB_S_TUNER

MTK_NON_DVB_S_TUNER

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

R142

2.7K

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

EAX64797001* : LD33B

EAX64872101* : LA33B

R140 4.7K

R139 4.7K

MTK_DVB_T2_TUNER

MTK_NON_DVB_T2_TUNER

I2C_SCL1

I2C_SDA1

2.7K

M24256-BRMN6TP

7 WC

6 SCL

5 SDA

NVRAM_ST

IC100-*1

R135 33

R134 33

R137 4.7K

R136 4.7K

R138

2.7K

MTK_CP_BOX

MTK_NON_CP_BOX

1 E0

2 E1

3 E2

4 VSS

C100 0.1uF

R131 4.7K

R129 4.7K

+3.3V_NORMAL

OPT

R133

2.7K

MTK_DDR_1.25GB

MTK_DDR_1.5GB

+3.3V_NORMAL

R130 4.7K

R128 4.7K

R132

2.7K

MODULE_V12

R125 4.7K

R126 22 OPT

R127 22

MODULE_V13

NVRAM

OPT

OPT

R124

1.2K

R123 4.7K

R122 4.7K

6 SCL

5 SDA

AT24C256C-SSHL-T

7 WP

6 SCL

5 SDA

R121

1.2K

R108 4.7K

R107 4.7K

NVRAM_ATMEL

7 WC

R120 33

R115 33

R116 33

R117 33

R118 33

R119 33

R110 33

R111 33

R112 33

R113 33

R114 33

R109 33

MTK_FHD

MTK_HD

HDCP EEPROM

M24C16-R

OPT

+3.3V_NORMAL

R106 4.7K

R104 4.7K

1 NC_1

2 NC_2

3 NC_3

4 VSS

1 A0

2 A1

3 A2

4 GND

R105 4.7K

R103 4.7K

R102

4.7K OPT

STB_SCL

STB_SDA

OPCTRL_11_SCL

OPCTRL_10_SDA

OSCL1

OSDA1

OSCL2

OSDA2

OSCL0

OSDA0

OPCTRL_1_SCL

OPCTRL_0_SDA

+3.3V_NORMAL

R101

4.7K

R100

4.7K OPT

Show 7 more labels / short text on this page
Write Protection · Country_AJJA · Non_Country_AJJA · FRC_120Hz · NON_FRC_60Hz · Country_TW · NON_Country_TW
Page 24 of the LG Electronics 47LA71** user manual — OPT
Page 24 · click to enlarge
Page 24
LG Electronics 47LA71** — #EV# diagram (page 24)
Fig. 42

D0+_HDMI3_JACK

D0-_HDMI3_JACK

D1+_HDMI3_JACK

D1-_HDMI3_JACK

D2+_HDMI3_JACK

D2-_HDMI3_JACK

CK+_HDMI3_JACK

CK-_HDMI3_JACK

D0+_HDMI1_SOC

D0-_HDMI1_SOC

D1+_HDMI1_SOC

D1-_HDMI1_SOC

D2+_HDMI1_SOC

D2-_HDMI1_SOC

CK+_HDMI1_SOC

CK-_HDMI1_SOC

D0+_HDMI4_MHL

D0-_HDMI4_MHL

D1+_HDMI4_MHL

D1-_HDMI4_MHL

D2+_HDMI4_MHL

D2-_HDMI4_MHL

CK+_HDMI4_MHL

CK-_HDMI4_MHL

0.1uF

AVDD_33SB

HDMI_ARC

Place at JACK SIDE

TXVP_0 AL13

TXVN_0 AM13

RXVP_1 AL12

RXVN_1 AM12

PHYLED1 AF13

PHYLED0 AJ13

REXT AN12

AVDD33_ETH AN14

AVSS33_ELDO AE13

AVSS33_LD AC16

AVSS33_COM AC15

HDMI_0_RX_0 AG30

HDMI_0_RX_0B AG31

HDMI_0_RX_1 AF30

HDMI_0_RX_1B AF31

HDMI_0_RX_2 AE32

HDMI_0_RX_2B AE33

HDMI_0_RX_C AG32

HDMI_0_RX_CB AG33

HDMI_1_RX_0 AD30

HDMI_1_RX_0B AD31

HDMI_1_RX_1 AC32

HDMI_1_RX_1B AC33

HDMI_1_RX_2 AC30

HDMI_1_RX_2B AC31

HDMI_1_RX_C AE30

HDMI_1_RX_CB AE31

HDMI_2_RX_0 Y30

HDMI_2_RX_0B Y31

HDMI_2_RX_1 W32

HDMI_2_RX_1B W33

HDMI_2_RX_2 W30

HDMI_2_RX_2B W31

HDMI_2_RX_C AA30

HDMI_2_RX_CB AA31

HDMI_3_RX_0 U30

HDMI_3_RX_0B U31

HDMI_3_RX_1 T32

HDMI_3_RX_1B T33

HDMI_3_RX_2 T30

HDMI_3_RX_2B T31

HDMI_3_RX_C V30

HDMI_3_RX_CB V31

+5V_NORMAL

LGE2122[A2_M13]

HP_LOUT

HP_ROUT

R308 1.2K OPT

R309 100K

LGE2122[A2_M13]

HP_OUT

0.22uF 10V

HP_OUT

0.22uF 10V

AVDD12_HDMI_0_RX AA33

AVDD12_HDMI_1_RX AA32

AVDD12_HDMI_2_RX P33

AVDD12_HDMI_3_RX P32

AVSS33_HDMI_RX_1 AE27

AVSS33_HDMI_RX_2 T25

AVSS33_HDMI_RX_3 W25

AVSS33_HDMI_RX_4 AD27

BLM18PG121SN1D

AVDD33_USB_P0P1P2 K33

HP_OUT

HP_OUT

BLM18PG121SN1D

R303 82

HDMI_0_SCL AC27

HDMI_1_SCL AB27

HDMI_2_SCL AA26

HDMI_3_SCL W27

HDMI_0_SDA AC26

HDMI_1_SDA AB26

HDMI_2_SDA Y26

HDMI_3_SDA W26

HDMI_0_PWR5V AE29

HDMI_1_PWR5V Y27

HDMI_2_PWR5V AA28

HDMI_3_PWR5V V28

HDMI_0_HPD AD29

HDMI_1_HPD AA27

HDMI_2_HPD AA29

HDMI_3_HPD V29

AVDD33_HDMI AH33

AVDD33_USB_P3 AN8

AVSS33_USB_P1 M25

AVSS33_USB_P3 AE11

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

HDMI_CEC V26

USB_DP_P0 H32

USB_DM_P0 H33

USB_DP_P1 J32

USB_DM_P1 J31

USB_DP_P2 K32

USB_DM_P2 K31

USB_DP_P3 AN10

USB_DM_P3 AM10

R302

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

HP_ROUT_AMP

ARC

HP_LOUT_AMP

TP381

0.1uF

R305 1K

R306 1K

R307 1K

USB_DP3

USB_DM3

USB_DP2

USB_DM2

USB_DP1

USB_DM1

HDMI_CEC

0.1uF

0.1uF

VDD3V3

DDC_SCL_3_JACK

DDC_SCL_1_SOC

DDC_SCL_MHL

DDC_SDA_3_JACK

DDC_SDA_1_SOC

DDC_SDA_MHL

5V_HDMI_3_JACK

5V_HDMI_1_SOC

HDMI_HPD_3_JACK

HDMI_HPD_1_SOC

HDMI_HPD_4_MHL

0.1uF

Port was changed !!!!

R382 0

R383

5VBUS

0.1uF

+1.2V_MTK_AVDD

0.1uF 16V

OPT

VDD3V3_HDMI

0.1uF 16V

OPT

WIFI_DP

WIFI_DM

Wake On Lan · C311 1uF

Page 25 of the LG Electronics 47LA71** user manual — B
Page 25 · click to enlarge
Page 25
LG Electronics 47LA71** — #EV# diagram (page 25)
Fig. 43

TP501

LAN_JACK_POWER

DECAP FOR SOC (HIDDEN - UCC) DECAP FOR SOC Rework (BOTTOM)

0.1uF

OPT

TP500

0.1uF

OPT +1.2V_MTK_CORE

+1.2V_MTK_CORE

POWER_ON/OFF1

OPT

VDD3V3

0.1uF 16V

TP503

OPT

+1.5V_DDR C541

0.1uF 16V

3.3V_EMMC

BLM18PG121SN1D

+1.2V_MTK_CORE

0.1uF

TP502

+1.5V_DDR

OPT

+3.3V_NORMAL

0.1uF C520

+1.2V_MTK_AVDD

0.1uF

AVDD_33SB

0.1uF C514

BLM18PG121SN1D

2 VOUT 3 VIN

OPT +1.2V_MTK_CORE

AP2121N-3.3TRE1

GND

0.1uF

0.1uF 16V

+3.5V_ST_WAKE

0.1uF

2.2uF

0.1uF

+3.5V_ST_WAKE

AVDD_33SB

ZD500 5V OPT

VDD3V3

0.1uF

BLM18PG121SN1D

0.1uF 16V

0.1uF

OPT

+3.3V_NORMAL

BLM18PG121SN1D

BLM18PG121SN1D

D

OPT

Q501

PMV48XP

G

S

MMBT3904(NXP)

4.7uF 10V

+3.5V_ST_WAKE

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Q500

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

E

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

R502 10K R501 1.8K

4.7uF 10V OPT

B

+3.5V_ST

VDD3V3

R500

10K

WOL_CTL

Show 9 more labels / short text on this page
10uF · 10uF · 1uF 10V · 5600mA · 10uF · 10uF · 60mA · 10uF · 10uF
Page 26 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 26 · click to enlarge
Page 26
LG Electronics 47LA71** — #EV# diagram (page 26)
Fig. 44

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

Page 28 of the LG Electronics 47LA71** user manual — AR900 47 CI
Page 28 · click to enlarge
Page 28
LG Electronics 47LA71** — #EV# diagram (page 28)
Fig. 45

Close to CI Slot

CI_TS_CLK

CI_TS_VAL

R917 47 CI CI_TS_SYNC

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

CI_TS_DATA[0]

CI_TS_DATA[1]

CI_TS_DATA[2]

CI_TS_DATA[3]

CI_TS_DATA[4]

CI_TS_DATA[5]

CI_TS_DATA[6]

CI_TS_DATA[7]

CI_MDI[0]

CI_MDI[1]

CI_MDI[2]

CI_MDI[3]

CI_MDI[4]

CI_MDI[5]

CI_MDI[6]

CI_MDI[7]

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

Close to CI Slot

Close to MT5369

Close to CI Slot

AR900 47 CI

AR901 47 CI

R915 47 CI

R916 47 CI

AR902

AR903

Close to MT5369

R907 47 CI

R908 47 CI

R909 47 CI

Close to MT5398

MT5398_TS_OUT[0]

MT5398_TS_OUT[2]

MT5398_TS_OUT[7]

MT5398_TS_OUT[1]

MT5398_TS_OUT[3]

MT5398_TS_OUT[4]

MT5398_TS_OUT[5]

MT5398_TS_OUT[6]

MT5398_TS_IN[0]

MT5398_TS_IN[1]

MT5398_TS_IN[2]

MT5398_TS_IN[3]

MT5398_TS_IN[4]

MT5398_TS_IN[5]

MT5398_TS_IN[6]

MT5398_TS_IN[7]

CI TS INPUT

MT5398_MIVAL_ERR

CI TS OUTPUT

MT5398_MISTRT

MT5398_MCLKI

MT5398_TS_OUT[0-7]

MT5398_TS_IN[0-7]

MT5398_TS_SYNC

MT5398_TS_CLK

MT5398_TS_VAL

12pF 50V OPT · 12pF 50V OPT

Page 30 of the LG Electronics 47LA71** user manual — MICOM_DEBUG
Page 30 · click to enlarge
Page 30
LG Electronics 47LA71** — #EV# diagram (page 30)
Fig. 46

25 P27/ANI7 26 P26/ANI6 27 P25/ANI5 28 P24/ANI4 29 P23/ANI3 30 P22/ANI2 31 P21/ANI1/AVREFM 32 P20/ANI0/AVREFP 33 P130 34 P01/TO00/RXD1 35 P00/TI00/TXD1 36 P140/PCLBUZ0/INTP6

25 P27/ANI7 26 P26/ANI6 27 P25/ANI5 28 P24/ANI4 29 P23/ANI3 30 P22/ANI2 31 P21/ANI1/AVREFM 32 P20/ANI0/AVREFP 33 P130 34 P01/TO00/RXD1 35 P00/TI00/TXD1 36 P140/PCLBUZ0/INTP6

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Don’t remove R3014,

not making float P40

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

GP4 High/MID Power SEQUENCE

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

MICOM MODEL OPTION

Renesas MICOM

MICOM_DEBUG

MICOM_RESET

MODEL1_OPT_0

MODEL1_OPT_1

MODEL1_OPT_2

MODEL1_OPT_3

MODEL1_OPT_4

MODEL1_OPT_5

R3007-*2 22K

MICOM_OLED_FRC

R3007-*1 56K

MICOM_OLED_MAIN

R3016 1K

POWER_ON/OFF2_1

POWER_ON/OFF2_2

POWER_ON/OFF2_3

POWER_ON/OFF2_4

+3.5V_ST

R3014 10K

POWER_ON/OFF!

R3013 10K MICOM_LOGO_LIGHT

R3012 10K MICOM_NON_LOGO_LIGHT

For Debug

MICOM_DEBUG

SOC_RESET

+3.5V_ST

MICOM_DEBUG

R3010 10K MICOM_TOUCH_KEY

R3008 10K MICOM_TACT_KEY

12507WS-04L

P3000

R3007 10K MICOM_PDP

R3005 10K MICOM_LCD/OLED

R3006 10K MICOM_NC4_8PIN

R3004 10K MICOM_GP3_12/15PIN

R3003 10K MICOM_H13

R3001 10K MICOM_M13

R3002 10K MICOM_GED

R3000 10K MICOM_NON_GED

Page 31 of the LG Electronics 47LA71** user manual — +12V
Page 31 · click to enlarge
Page 31
LG Electronics 47LA71** — #EV# diagram (page 31)
Fig. 47

21 HPD_IN 22 TX2+ 23 TX2- 24 TX1+ 25 TX1- 26 TX0+ 27 TX0- 28 TXC+ 29 TXC- 30 AVDD12

SIL_HPD/CBUS

R3376 0

R3375 10K

R3331 1K HDMI_HPD_3_JACK

DDC_SDA_3_JACK

DDC_SCL_3_JACK

PMBFJ177 G

OPT

DDC_SCL_4_JACK

+3.5V_ST

Q3304

Q3314

DDC_SDA_MHL

MMBT3904(NXP) E

2N7002K

R3374 10K

S

D

D

S

R3371 820

B

CK+_HDMI3_JACK

G

Q3301

UI : HDMI3

R3336

4.7K

D0-_HDMI3_JACK

D0+_HDMI3_JACK

D1-_HDMI3_JACK

D1+_HDMI3_JACK

UI : HDMI1

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

OPT

R3384

R3370

CK-_HDMI3_JACK

D2-_HDMI3_JACK

D2+_HDMI3_JACK

1K

1K

R3328 100

R3329 100

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

R3308 100

R3309 100

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

+12V

0.1uF 16V OPT

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

+12V

OPT

R3373

1/16W 5%

OPT

1K

VA3307 ADLC 5S 02 015

5VBUS

VA3301 ADLC 5S 02 015

R3330

B

1K

OPT

BLM18PG121SN1D

VA3300 ADLC 5S 02 015 OPT

R3386 180K R3387 120K

VA3306 ADLC 5S 02 015

RCLAMP0524PA

E

RCLAMP0524PA

SOC_RX

CK-_HDMI4_JACK

CK+_HDMI4_JACK

D0-_HDMI4_JACK

D0+_HDMI4_JACK

D1-_HDMI4_JACK

D1+_HDMI4_JACK

D2-_HDMI4_JACK

D2+_HDMI4_JACK

Q3303

MMBT3904(NXP)

CEC_REMOTE

5V_HDMI_3_JACK

CEC_REMOTE

D3320

OPT

HDMI_ARC

D3321

ADLC 5S 02 015 OPT

R3327

100K

OPT

OPT

OPT

VA3303 ADLC 5S 02 015

R3342 0

OPT

VA3304

VA3302 ADLC 5S 02 015

OPT

VA3305 ADLC 5S 02 015

CE_REMOTE

51U019S-312HFN-E-R-B-LG

HP_DET

DDC_DATA

DDC_CLK

CK_GND

8 D0_GND

5 D1_GND

2 D2_GND

51U019S-312HFN-E-R-B-LG

GND

14 NC

CK-

10 CK+

9 D0-

7 D0+

6 D1-

4 D1+

3 D2-

1 D2+

CE_REMOTE

SIDE

BODY_SHIELD

HP_DET

DDC_DATA

DDC_CLK

CK_GND

8 D0_GND

5 D1_GND

2 D2_GND

JK3301

BODY_SHIELD GND

GND

ARC

CK-

10 CK+

9 D0-

7 D0+

6 D1-

4 D1+

3 D2-

1 D2+

GND

SIDE

JK3303

EAG62611204

EAG62611204

Page 32 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 32 · click to enlarge
Page 32
LG Electronics 47LA71** — #EV# diagram (page 32)
Fig. 48

JK3602

JST1223-001

4 FIX_POLE

GND

VINPUT

SPDIF

0.1uF 16V

+3.3V_NORMAL

R3611

2.7K OPT

R3610

SPDIF OUT

SPDIF_OUT

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

Fiber Optic

Page 33 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 33 · click to enlarge
Page 33
LG Electronics 47LA71** — #EV# diagram (page 33)
Fig. 49

JK3700

PEJ034-01

3 E_SPRING

4 R_SPRING

5 T_SPRING

7B B_TERMINAL2

6B T_TERMINAL2

+3.3V_NORMAL

R3700

10K

R3701

1K

HP_ROUT

HP_LOUT

HP_DET

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

Page 34 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 34 · click to enlarge
Page 34
LG Electronics 47LA71** — #EV# diagram (page 34)
Fig. 50

SOC_RX

SOC_TX

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

Page 35 of the LG Electronics 47LA71** user manual — +3.5V_ST
Page 35 · click to enlarge
Page 35
LG Electronics 47LA71** — #EV# diagram (page 35)
Fig. 51

OPT

R4125 10K

LED_R

22 LOGO_LIGHT

R4131

E

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

MMBT3904(NXP)

+3.5V_ST

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

5.6V AMOTECH CO., LTD.

LED_R

LOGO_LIGHT

B

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

Q4100

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

D4101

R4107

10K

OPT

LOGO_LIGHT

5.6V AMOTECH CO., LTD.

R4134 1K

IR

D4100

OPT

0.1uF

BLM18PG121SN1D

0.1uF 16V

0.1uF

+3.5V_ST

OPT

R4133 10K

LOGO_LIGHT

+3.5V_ST

R4132 10K

LOGO_LIGHT

Place Near Micom

R4118

LOGO_LIGHT

+3.5V_ST

10K 5%

R4117

10K 5%

R4113

R4114

KEY1

KEY2

100pF 50V · C4104 1000pF 50V

Page 36 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 36 · click to enlarge
Page 36
LG Electronics 47LA71** — #EV# diagram (page 36)
Fig. 52

/USB_OCD2

/USB_OCD3

+3.3V_NORMAL

USB3

R4302 10K

+5V_USB_2

+5V_USB_3

R4301 10K

OCP USB2/3

[EP]GND

8 FLT1

7 OUT1

6 OUT2

5 FLT2

TPS2066CDGNR

THERMAL

1 GND

2 IN

3 EN1

4 EN2

+5V_NORMAL

USB_CTL2

USB_CTL3

0.1uF 16V

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

10uF 10V USB3 · 10uF 10V

Page 37 of the LG Electronics 47LA71** user manual — +5V_NORMAL
Page 37 · click to enlarge
Page 37
LG Electronics 47LA71** — #EV# diagram (page 37)
Fig. 53

DVR Ready OCP USB1 USB1

10uF 10V C4502

USB_DM1

USB_DP1

+5V_USB_1

8 OUT_3

7 OUT_2

6 OUT_1

5 OC

BD82020FVJ

1 GND

2 IN_1

3 IN_2

4 EN

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

+5V_NORMAL

0.1uF 16V

R4501

10K

+3.3V_NORMAL

R4500

10K OPT

/USB_OCD1

USB_CTL1

Page 38 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 38 · click to enlarge
Page 38
LG Electronics 47LA71** — #EV# diagram (page 38)
Fig. 54

DTV/MNT_V_OUT

LG Electronics 47LA71** — DTV/MNT_V_OUT diagram (page 38)
Fig. 55

+3.3V_NORMAL

Full Scart(18 Pin Gender)

1 AUDIO_R_OUT 2 AUDIO_R_IN 3 AUDIO_L_OUT 4 AUDIO_GND 5 B_GND 6 AUDIO_L_IN 7 B_OUT 8 ID 9 G_GND 10 D2B_IN 11 G_OUT 12 D2B_OUT 13 R_GND 14 RGB_GND 15 R_OUT 16 RGB_IO 17 SYNC_GND1 18 SYNC_GND2 19 SYNC_OUT 20 SYNC_IN 21 COM_GND 22 AV_DET

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

Page 39 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 39 · click to enlarge
Page 39
LG Electronics 47LA71** — #EV# diagram (page 39)
Fig. 56

Ethernet Block

EPHY_TDP

EPHY_TDN

EPHY_RDP

EPHY_RDN

5.5V LAN_ESD

D5003

5.5V LAN_ESD

D5002

0.01uF 50V

5.5V LAN_ESD

D5001

0.1uF 16V

D5000

5.5V LAN_ESD

RJ45VT-01SN002

NON_LN56

JK5000

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

Page 40 of the LG Electronics 47LA71** user manual — +24V
Page 40 · click to enlarge
Page 40
LG Electronics 47LA71** — #EV# diagram (page 40)
Fig. 57

21 OUT2A 22 PGND2A 23 BST2A 24 VDR2 25 AGND 26 VCC5 27 VDR1 28 BST1B 29 PGND1B 30 OUT1B

-->32"POLA/ROW LPB’s 3.5st drop time is very fast

-->For fixing AC-OFF POP noise 32"POLA/ROW model

0.1uF 16V

OPT

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

Q1801 1ST : 0TRIY80001A 2ND : 0TR387500AA

POWER_DET

AMP_MUTE_PWR_DET

R5402 100

R5403 100

R5419 100

DUAL COMPONENT

R5405 100

AMP_MUTE_MICOM

AMP_MUTE_MICOM

AMP_MUTE_MICOM E

MMBT3904(NXP)

+3.3V_NORMAL

R5401 10K

Q5400

[AMP_MUTE_PWR_DET]

0.1uF C5401

+24V_AMP

I2C_SDA1

I2C_SCL1

B

AMP_MUTE_MICOM

CIS21J121

R5400 10K

AUD_LRCH

AUD_LRCK

AUD_SCK

0.1uF C5400

+24V

AMP_MUTE

33pF 50V · 33pF 50V · 1000pF 50V

Page 41 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 41 · click to enlarge
Page 41
LG Electronics 47LA71** — #EV# diagram (page 41)
Fig. 58

AUD_OUT >> EU/CHINA_HOTEL_OPT

DTV/MNT_L_OUT

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

1uF 25V EU

Page 42 of the LG Electronics 47LA71** user manual — HP_ROUT_MAIN
Page 42 · click to enlarge
Page 42
LG Electronics 47LA71** — #EV# diagram (page 42)
Fig. 59

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

HP_ROUT_MAIN

Page 43 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 43 · click to enlarge
Page 43
LG Electronics 47LA71** — #EV# diagram (page 43)
Fig. 60
LG Electronics 47LA71** — #EV# diagram (page 43)
Fig. 61

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

Page 44 of the LG Electronics 47LA71** user manual — SMARTCARD_PWR_SEL/SD_EMMC_DATA[1]
Page 44 · click to enlarge
Page 44
LG Electronics 47LA71** — #EV# diagram (page 44)
Fig. 62

75 ohm in I/O is for short circuit Protection

R6301

R6302

R6300 22

JAPAN

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

SMARTCARD_PWR_SEL/SD_EMMC_DATA[1]

Page 45 of the LG Electronics 47LA71** user manual — TDS’W’-J551F : Japan Dual NIM
Page 45 · click to enlarge
Page 45
LG Electronics 47LA71** — #EV# diagram (page 45)
Fig. 63

TU_M/W = apply TDSM&TDSW Type Tuner else : Max mA

TU_CVBS

LG Electronics 47LA71** — TU_CVBS diagram (page 45)
Fig. 64

I2C_SCL4

I2C_SDA4

should be guarded by ground 3. Signal Width >= 12mils

+3.3V_TU

LG Electronics 47LA71** — +3.3V_TU diagram (page 45)
Fig. 65

+1.23V_D_Demod

TU_Q/W

+3.3V_TU

RF_SWITCH_CTL_TU

/TU_RESET1_TU

I2C_SCL6_TU

I2C_SDA6_TU

TUNER_SIF_TU

TU_+1.8V_TU

TU_CVBS_TU

IF_AGC_TU

IF_P

IF_N

+3.3V_TU

CN_RESET_TU

FE_DEMOD1_TS_ERROR

FE_DEMOD1_TS_SYNC

FE_DEMOD1_TS_VAL

FE_DEMOD1_TS_CLK

FE_DEMOD1_TS_DATA[0]

FE_DEMOD1_TS_DATA[1]

FE_DEMOD1_TS_DATA[2]

FE_DEMOD1_TS_DATA[3]

FE_DEMOD1_TS_DATA[4]

FE_DEMOD1_TS_DATA[5]

FE_DEMOD1_TS_DATA[6]

FE_DEMOD1_TS_DATA[7]

+1.23V_D_Demod_TU

/S2_RESET_TU

+3.3V_TU

LNB_TX

I2C_SCL4_TU

I2C_SDA4_TU

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

TU_Q_T2 = apply TDSQ type tuner and T2 country

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

TDS’Q’-G601D : T2/C/S2 Combo Horizontal Type

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

13’ Tuner Type for Global TDS’S’-G501D : T/C Half NIM Horizontal Type

TDS’Q’-G501D : T/C/S2 Combo Horizontal type

TDS’M’-C601D : China NIM with Isolater Type

TDS’Q’-G651D : T2/C/S2 Combo Vertical Type

1. TU 2. Tuner Name = TDS’S’,TDS’Q’... 3. Country Name = T,T2,S2,KR,US,BR ...

TDS’W’-J551F : Japan Dual NIM

Global F/E Option Name

Example of Option name

Power_D_Demod_TU

Page 46 of the LG Electronics 47LA71** user manual — TU_W
Page 46 · click to enlarge
Page 46
LG Electronics 47LA71** — #EV# diagram (page 46)
Fig. 66

FE_DEMOD1_TS_DATA[0]

FE_DEMOD1_TS_DATA[1]

FE_DEMOD1_TS_DATA[2]

FE_DEMOD1_TS_DATA[3]

FE_DEMOD1_TS_DATA[4]

FE_DEMOD1_TS_DATA[5]

FE_DEMOD1_TS_DATA[6]

FE_DEMOD1_TS_DATA[7]

RF_SWITCH_CTL_TU

FE_DEMOD1_TS_ERROR

FE_DEMOD1_TS_SYNC

FE_DEMOD1_TS_VAL

FE_DEMOD1_TS_CLK

+1.23V_D_Demod_TU

FE_DEMOD2_TS_ERROR

FE_DEMOD2_TS_SYNC

FE_DEMOD2_TS_VAL

FE_DEMOD2_TS_CLK

FE_DEMOD2_TS_DATA

FE_DEMOD3_TS_ERROR

FE_DEMOD3_TS_SYNC

FE_DEMOD3_TS_VAL

FE_DEMOD3_TS_CLK

FE_DEMOD3_TS_DATA

/TU_RESET1_TU

TUNER_SIF_TU

/S2_RESET_TU

I2C_SCL6_TU

I2C_SDA6_TU

TU_+1.8V_TU

TU_CVBS_TU

IF_AGC_TU

CN_RESET_TU

I2C_SCL4_TU

I2C_SDA4_TU

+3.3V_TU

+3.3V_TU

+3.3V_TU

LNB_OUT

IF_P

IF_N

LNB_TX

LG Electronics 47LA71** — FE_DEMOD2_TS_ERROR diagram (page 46)
Fig. 67

TDSW-J501F(B)

TU6602

TDSQ-G501D(B)

TU6601

TDSS-G501D(B)

A1 A1 B1 B1

SHIELD

TU_M/W

0.1uF

1 NC_1

2 RESET

3 SCL

4 SDA

6 NC_2

8 NC_3

9 IF_AGC

10 DLIF_[P]

11 DLIF_[N]

TU6600

TU_S_T

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

/TU_RESET2

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

TU_GND_B

TU_M_CN

TU_W

R6611 0

GND seperation for CHINA tuner

TU_W

R6610 0

TU_W

TU_GND_A

R6609 0

TU_W

R6608 0

TU_GND_B

R6607 0 TU_S/N/Q/W

R6606 0 TU_S/N/Q/W

R6605 0 TU_S/N/Q/W

R6604 0 TU_S/N/Q/W

Power_D_Demod_TU · C6604 1000pF · C6603 1000pF TU_M_CN

Page 47 of the LG Electronics 47LA71** user manual — 14 DOUT1
Page 47 · click to enlarge
Page 47
LG Electronics 47LA71** — #EV# diagram (page 47)
Fig. 68

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

14 DOUT1

13 RIN1

12 ROUT1

11 DIN1

10 DIN2

8 RIN2 9 ROUT2

15 GND

JAPAN_HOTEL

MAX3232CDR

EAN41348201

1 C1+

2 V+

4 C2+

7 DOUT2

0.1uF

0.1uF

0.1uF

0.1uF

0.33uF

OPT

JAPAN_HOTEL

JAPAN_HOTEL

JAPAN_HOTEL

JAPAN_HOTEL

Page 48 of the LG Electronics 47LA71** user manual — R6900
Page 48 · click to enlarge
Page 48
LG Electronics 47LA71** — #EV# diagram (page 48)
Fig. 69

Input trace widths should be sized to conduct at least 3A

Ouput trace widths should be sized to conduct at least 2A

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

R6900

2.2K 1W LNB

D6900

(Option:LNB)

LNB

Surge protectioin

Close to Tuner

33pF LNB

18pF LNB

LNB_OUT

Page 49 of the LG Electronics 47LA71** user manual — R7100 33 LGD_2D/3D_CTRL
Page 49 · click to enlarge
Page 49
LG Electronics 47LA71** — #EV# diagram (page 49)
Fig. 70
LG Electronics 47LA71** — #EV# diagram (page 49)
Fig. 71

BLM18SG121TN1D

TXA0N

TXA0P

TXA1N

TXA1P

TXA2N

TXA2P

TXACLKN

TXACLKP

TXA3N

TXA3P

TXA4N

TXA4P

TXB0N

TXB0P

TXB1N

TXB1P

TXB2P

TXBCLKN

TXBCLKP

TXB3N

TXB3P

TXB4N

TXB4P

I2C_SDA1

I2C_SCL1

LVDS_51PIN

2D/3D_CTL

OPC_EN

PWM_DIM1

PANEL_VCC

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

R7109 0

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

R7100 33 LGD_2D/3D_CTRL

OPT

R7110 33 AUO_L/D_EN

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

R7108 33

OPC_EN

R7105 33 CP_BOX

R7106 33 CP_BOX

R7107 33

6 AUO_65_MIRROR

10 L/DIM_ENABLE

7 LVDS_SEL

27 BIT_SEL

19 RACLKN

20 RACLKP

35 RBCLKN

36 RBCLKP

LVDS

FI-RE51S-HF-J-R1500

1 NC

2 NC

3 NC

4 NC

5 NC

8 NC

9 NC

11 GND

12 RA0N

13 RA0P

14 RA1N

15 RA1P

16 RA2N

17 RA2P

18 GND

21 GND

22 RA3N

23 RA3P

24 RA4N

25 RA4P

26 GND

28 RB0N

29 RB0P

30 RB1N

31 RB1P

32 RB2N

33 RB2P

34 GND

37 GND

38 RB3N

39 RB3P

40 RB4N

41 RB4P

42 GND

43 GND

44 GND

45 GND

46 GND

47 NC

48 VLCD

49 VLCD

50 VLCD

51 VLCD

LVDS_51PIN

GND

P7100

1000pF 50V OPT · 10uF 16V OPT · LGD_T-Con_Scanning

Page 50 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 50 · click to enlarge
Page 50
LG Electronics 47LA71** — #EV# diagram (page 50)
Fig. 72
LG Electronics 47LA71** — #EV# diagram (page 50)
Fig. 73

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

Page 51 of the LG Electronics 47LA71** user manual — R7755
Page 51 · click to enlarge
Page 51
LG Electronics 47LA71** — #EV# diagram (page 51)
Fig. 74

25 SS 26 COMP 27 SCL 28 SDA 29 VL 30 TCOMP 31 CTRLP 32 VGH 33 SWP 34 SWN 35 VGL 36 CTRLN

[Left Source(51PIN LOCATION)] [Right Source(41PIN LOCATION)]

THIS IS REVERSE PATTERN !!!!

BLM18PG121SN1D

GMA18

GMA16

GMA15

GMA14

GMA12

GMA10

GMA9

GMA7

GMA5

GMA4

GMA3

GMA1

EPI_H13

0.1uF 50V

0.1uF 16V

FL8S050HA1

P7703

EPI

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

R7700

2K 1/16W

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

EPI_LOCK6

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

H_VDD

VDD

Q7703 MMBT3904(NXP)

EPI_LOCK3

FROM SOC CH6

CH5

FROM SOC

CH4

FROM SOC

R7758

GMA1

GMA3

GMA4

GMA5

GMA7

GMA9

GMA10

GMA12

GMA14

GMA15

GMA16

GMA18

10K

VCOML_FB

VCOM_IN

VGH_EVEN

E

GIP_RST

VGL_I

VGH_ODD

VGH_F

VGH_R

Z_OUT

TXB2P

TXB2N

TXB1P

TXB1N

TXB0P

TXB0N

VST

CLK6

CLK5

CLK4

CLK3

CLK2

CLK1

MMBT3904(NXP)

B

R7757

10K

Q7702

+3.3V_NORMAL

10K

0.01uF 50V

E

B

0.1uF 50V

R7755

R7761

10K OPT

FL8S050HA1

P7702

EPI

EPI_LOCK6_SOURCE

Vcore · Vcore

Page 52 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 52 · click to enlarge
Page 52
LG Electronics 47LA71** — #EV# diagram (page 52)
Fig. 75

EPI

VDD VDD_EPI

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

EPI

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

68uF · 68uF

Page 53 of the LG Electronics 47LA71** user manual — 3.3V_EMMC
Page 53 · click to enlarge
Page 53
LG Electronics 47LA71** — #EV# diagram (page 53)
Fig. 76

Don’t Connect Power At VDDI

R8117 10K

EMMC_CMD_BALL

EMMC_CLK_BALL

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

DAT6

(Just Interal LDO Capacitor)

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

EMMC DATA LINE

DAT5

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

10K PULL/UP FOR M13

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

DAT4

DAT3

R8107 10K

R8106 10K

R8105 10K

R8104 10K

R8103 10K

0.1uF 16V OPT

3.3V_EMMC

R8102 10K

EMMC_SERIAL_22

R8101 10K

R8100 10K

EMMC_SERIAL_22

AR8100

AR8101

EMMC_CLK AR8102 22

EMMC_SERIAL_22

22 1/16W

22 1/16W

eMMC I/F

eMMC serial 100 ohm option

EMMC DATA LINE 47K PULL/UP

R8107-*1 47K

AR8102-*1

R8106-*1 47K

R8105-*1 47K

100 1/16W

R8104-*1 47K

AR8101-*1

EMMC_SERIAL_100

EMMC_DATA[0]

EMMC_DATA[1]

EMMC_DATA[2]

EMMC_DATA[3]

R8103-*1 47K

EMMC_DATA[4]

EMMC_DATA[5]

EMMC_DATA[6]

EMMC_DATA[7]

100 1/16W

R8102-*1 47K

EMMC_CMD

EMMC_RST

R8101-*1 47K

EMMC_DATA[0-7]

R8100-*1 47K

AR8100-*1

EMMC_SERIAL_100

100 1/16W

EMMC_SERIAL_100

10pF 50V OPT

Page 54 of the LG Electronics 47LA71** user manual — OPT
Page 54 · click to enlarge
Page 54
LG Electronics 47LA71** — #EV# diagram (page 54)
Fig. 77

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

OPT

10uF 35V

+24V_AMP

Page 55 of the LG Electronics 47LA71** user manual — ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
Page 55 · click to enlarge
Page 55
LG Electronics 47LA71** — #EV# diagram (page 55)
Fig. 78

USE Two serial TS Port for Japan : MTK

FE_DEMOD1_TS_DATA[1]

FE_DEMOD3_TS_CLK

FE_DEMOD1_TS_DATA[3]

FE_DEMOD3_TS_SYNC

FE_DEMOD1_TS_DATA[4]

FE_DEMOD1_TS_DATA[2]

FE_DEMOD3_TS_VAL

FE_DEMOD1_TS_CLK

FE_DEMOD2_TS_CLK

FE_DEMOD1_TS_SYNC

FE_DEMOD2_TS_SYNC

FE_DEMOD1_TS_DATA[0]

FE_DEMOD2_TS_DATA

FE_DEMOD1_TS_VAL

FE_DEMOD2_TS_VAL

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.

ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS

Page 56 of the LG Electronics 47LA71** user manual — #EV#
Page 56 · click to enlarge
Page 56
Page 56 of the LG Electronics 47LA71** user manual — #EV#
Page 57 of the LG Electronics 47LA71** user manual — 1 / 88
Page 57 · click to enlarge
Page 57

1 / 88

< Applicable Model : Mid-end Platform >

2013 LED/LCD TV Engineering guide

XXLA64/62/61*-Z*

XXLA69/66*-Z*

XXLA74*-Z*

XXLA71*-Z*

XXLN57*-Z*

Page 58 of the LG Electronics 47LA71** user manual — 2 / 88
Page 58 · click to enlarge
Page 58
1. New features 2. Main PCBs 3. Block Diagrams, IIC Map 4. Structure of TV set and connection of sub ass’ys 5. New sub ass’ys

2 / 88

- Instruction of new sub ass’ys

6. Adjust way of new features 7. Repair guide

◈ CONTENT ◈

Page 59 of the LG Electronics 47LA71** user manual — EPI Interface
Page 59 · click to enlarge
Page 59
LG Electronics 47LA71** — #EV# diagram (page 59)
Fig. 79

LOCK

Figure1. Topology

TCON

  • Lock signal cascading and feedback to T-Con

3 / 88

  • Point-Point topology (support 2 Pair option)

EPI(Embedded Point-Point Interface)

  • No data skew and better EMI margin
  • Better reliability on common noise
  • Bandwidth up to 1.85Gbps/pair

at FHD 120Hz 10 bit application

  • CDR (Clock Data Recovery)
  • Fewer lines than mini-LVDS
  • Embedded Control Data
  • Slim PCB design

EPI Interface

Features

Merits

Page 60 of the LG Electronics 47LA71** user manual — 4 / 88
Page 60 · click to enlarge
Page 60
LG Electronics 47LA71** — #EV# diagram (page 60)
Fig. 80

* Bandwidth Capability - FHD 120Hz 10Bit : 594Mbps@36Lines → 1.65Gbps@12Lines

- FHD 240Hz 10Bit : 594Mbps@72Lines →1.25Gbps@32Lines

LG Electronics 47LA71** — * Bandwidth Capability - FHD 120Hz 10Bit : 594Mbps@36Lines → 1.65Gbps@12Lines diagram (page 60)
Fig. 81 · * Bandwidth Capability - FHD 120Hz 10Bit : 594Mbps@3…

(FHD 120Hz)

(FHD 120Hz)

LG Electronics 47LA71** — (FHD 120Hz) diagram (page 60)
Fig. 82 · (FHD 120Hz)

What to change

LCM (T-con to S-Driver IC)

LG Electronics 47LA71** — What to change diagram (page 60)
Fig. 83 · What to change

4 / 88

-Slim S-PCB design (14mm Æ 10mm) helps slimmer TV

- Multiple number of wires needed for higher bandwidth

EPI Interface (mini-LVDS vs. EPI)

EPI (Embedded clock P-to-P Interface)

60Hz 120Hz 240Hz

Connector 60pin (2ea) 60pin (2ea) 80pin (2ea)

60Hz 120Hz 240Hz

960ch 960ch 720ch

Connector - 50 pin (2ea) 70pin (2ea)

No. of Signal 12 12 32

No. of Signal 36 36 72

HF miniLVDS FHD (10bit)

FHD (10bit)

Comparison

- Difficult to upgrade bandwidth limit

- Better reliability on common noise

- No data skew. Better EMI margin

- Lower cost ( Cable, Connector )

HF mini-LVDS

EPI

Page 61 of the LG Electronics 47LA71** user manual — @10bit, FHD120
Page 61 · click to enlarge
Page 61
LG Electronics 47LA71** — #EV# diagram (page 61)
Fig. 84
  • Fewer Lines : 12
  • Embedded clock : low EMI, Clock skew free
  • Point to Point
  • Data rate : 1.8Gbps
  • Embedded clock, Control
  • Transmission Overhead : 4bit delimiter

HF mini-LVDS EPI

  • Easy to PCB design

5 / 88

EPI Interface (mini-LVDS vs. EPI)

TCON

  • Too many lines : 36
  • Clock skew
  • EMI due to clock lines
  • Bandwidth limit
  • Multi Drop
  • Data rate: 660Mbps
  • External clock
  • Merit
  • Simple structure
  • Standardization

@10bit, FHD120

Topology

Protocol

Features

Demerit

Page 62 of the LG Electronics 47LA71** user manual — User Action Area
Page 62 · click to enlarge
Page 62
LG Electronics 47LA71** — #EV# diagram (page 62)
Fig. 85
LG Electronics 47LA71** — #EV# diagram (page 62)
Fig. 86
LG Electronics 47LA71** — #EV# diagram (page 62)
Fig. 87

Present and anticipated applications include contactless transactions, data exchange, and simplified setup of more complex

communications such as Wi-Fi. Communication is also possible between an NFC device and an unpowered NFC chip, called

Near field communication (NFC) is a set of standards for smartphones and similar devices to establish radio communication

with each other by touching them together or bringing them into close proximity, usually no more than a few centimetres.

From Smart phone

to Smart phone

From TV

to TV

LG Electronics 47LA71** — From Smart phone diagram (page 62)
Fig. 88 · From Smart phone
LG Electronics 47LA71** — From Smart phone diagram (page 62)
Fig. 89 · From Smart phone
LG Electronics 47LA71** — From Smart phone diagram (page 62)
Fig. 90 · From Smart phone

6 / 88

NFC Tag Player choose

NFC (Near field communication)

Samrt phone close to

a "tag".

User Action Area

Page 63 of the LG Electronics 47LA71** user manual — To PSU
Page 63 · click to enlarge
Page 63

Main PCB for Broadband Main + TCON all in one

LNB IC Block

model

Only S model

1 Main processor, DDR Memory

S

Micom for Key/IR sensing

LG Electronics 47LA71** — Main PCB for Broadband Main + TCON all in one diagram (page 63)
Fig. 91 · Main PCB for Broadband Main + TCON all in one
LG Electronics 47LA71** — Main PCB for Broadband Main + TCON all in one diagram (page 63)
Fig. 92 · Main PCB for Broadband Main + TCON all in one
LG Electronics 47LA71** — Main PCB for Broadband Main + TCON all in one diagram (page 63)
Fig. 93 · Main PCB for Broadband Main + TCON all in one

eMMC Memory

Audio AMP

6 Level shifter

5 EPI Wafer

PMIC

PCB P/No : EAX64797003

LG Electronics 47LA71** — eMMC Memory diagram (page 63)
Fig. 94 · eMMC Memory
LG Electronics 47LA71** — eMMC Memory diagram (page 63)
Fig. 95 · eMMC Memory
LG Electronics 47LA71** — eMMC Memory diagram (page 63)
Fig. 96 · eMMC Memory

7 / 88

Chassis : LD33B

LG Electronics 47LA71** — 7 / 88 diagram (page 63)
Fig. 97

To PSU

xxLA660S-Zx

WIFI/BT

Key+IR

Front Spk

To module

Page 64 of the LG Electronics 47LA71** user manual — DVB-S DEMOD
Page 64 · click to enlarge
Page 64

ASSY

SUB

LG Electronics 47LA71** — ASSY diagram (page 64)
Fig. 98

DVB-S DEMOD

(S2)

LNB

T/C/S2 Without ATV

1. LGE2122 Block Diagram

DVB-S : I2C 4

Cable TUNER

(T/C/A)

TUNER

(S2)

MHL : I2C 4 MHL

Air/

MHL 1A

SIL1392

R

E

A

R

(H)

Page 65 of the LG Electronics 47LA71** user manual — I2C_SDA4
Page 65 · click to enlarge
Page 65

TUNER(S)

TUNER(D)

MHL IC105

LNB 33Ω

NVRAM

22Ω

I2C_SCL5 33Ω 33Ω

33Ω 33Ω

+3.3V_Normal

+3.3V_Normal

+3.3V_Normal

2.7KΩ

2.7KΩ

2.7KΩ

33Ω

LG Electronics 47LA71** — TUNER(S) diagram (page 65)
Fig. 99

I2C_SDA4

I2C_SCL4

I2C_SDA5

I2C_SDA6

I2C_SCL6

LGE 2122

I2C_SDA3

I2C_SCL3

I2C_SDA2

I2C_SCL2

I2C_SDA1

I2C_SCL1 100Ω

+3.3V_Normal

+3.3V_Normal

+3.3V_Normal

33Ω

33Ω

33Ω

2.7KΩ

2.7KΩ

1.2KΩ

2. LGE 2122 I2C Block Diagram

+3.5V_ST

Local dimming 33Ω

HDCP EEPROM 22Ω

3.3KΩ

Renesas MICOM

NTP7513(AMP)

PMIC

P7600

Page 66 of the LG Electronics 47LA71** user manual — 5V USB 1CH DCDC 4A 2CH OCP 1.2A USB2(Max 1.2A)
Page 66 · click to enlarge
Page 66
LG Electronics 47LA71** — #EV# diagram (page 66)
Fig. 100

5V USB 1CH DCDC 4A 2CH OCP 1.2A USB2(Max 1.2A)

TUNER(+1.23V)

MTK (DDRV)

DDR(VDDQ)

DDR(VDD)

1.5V DDR 3A

1.23V 2A

LNB option

+12V_LNB

3. Power Block Diagram

NTP_7400(PVDD1)

NTP_7400(PVDD2)

PANEL_POWER

MICOM(VDD)

PANEL_VCC

IR A'ssy

AMP

Page 67 of the LG Electronics 47LA71** user manual — [+3.3V_S2_DEMOD] 32
Page 67 · click to enlarge
Page 67
LG Electronics 47LA71** — #EV# diagram (page 67)
Fig. 101

CI Slot

TS_OUT_SYNC

ADDR[0-14]

TS_OUT_CLK

TS_OUT_VAL

[GPIO34-41] TS_OUT[0-7]

M31[CI_TSCLK] CARD_EN1

CARD_EN2

CI_RESET

[GPIO18-25] TS_IN[0-7]

CI_DET1 L33[SPI_CLK]

CI_DET2 L30[SPI_CLK1]

DAT[0-7]

CI_WAIT

INPACK

WR_EN

IOWD

/IRQA

O_EN

VS1 M27[PVR_TS_VAL]

IORD

REG

CI_TS_SYNC

47 Ω MT5398_TS_IN[0-7] CI_TS_DATA[0-7]

CI_TS_CLK

CI_TS_VAL

Power detect PCM_5V_CTL +5V_CI_ON

CI_ADDR[0-14] CI_A_ADDR[0-14]

47 Ω MT5398_TS_OUT[0-7] CI_MDI[0-7]

+5V_CI_ON +3.3V_NORMAL

CI_DATA[0-7] CI_A_DATA[0-7]

47K Ω

PCM_INPACK /PCM_WAIT

/PCM_A_REG

/CI_CD1

/CI_CD2

/PCM_CE1

/PCM_CE2

/PCM_IOWR

/PCM_IORD

/PCM_IRQA

PCM_RST

/PCM_WE /PCM_OE

CI_VS1

10K Ω

MTK5398_TS_CLK

MTK5398_TS_SYNC MTK5398_TS_VAL

F28[TCON12]

LG Electronics 47LA71** — CI Slot diagram (page 67)
Fig. 102 · CI Slot

N34[SPI_DATA]

N35[SPI_CLE]

[GPIO0-14]

[GPIO26-33]

T34[DEMOD_RST]

P34[PVR_TSDATA1]

N36[CI_INT]

P33[PVR_TSDATA0]

R36[CI_TSVAL]

R37[CI_TSSYNC]

R33[PVR_TSSYNC]

R3[PVR_TSCLK]

R35[CI_TSDATA0]

LGE 2122

LNB

A8303SESTR-TB

R29 [DEMOD_TSSYNC]

AM27 [ADCINP_DEMOD]

AN27 [ADCINN_DEMOD]

P27 [DEMOD_TSVAL]

P30 [DEMOD_TSCLK]

[DEMOD_TSDATA0-7]

[RESET] 2 AG24 [ADIN6_SRV]

[S2_RESET] 31 AM18 [ADIN7_SRV]

AJ19 [OPCTRL0]

AF19[OPCTRL1]

10 [TONECTRL]

AP6 [SCL3]

AR6 [SDA3]

2 [LNB]

7 [SCL]

8 [SDA]

ADCINP_DEMOD

ADCINN_DEMOD

33 Ω 33Ω

FE_DEMOD1_TS_DATA [0-7]

22 Ω

FE_DEMOD1_TS_SYNC

+3.3V_NORMAL

FE_DEMOD1_TS_VAL

FE_DEMOD1_TS_CLK

+1.23V_D_Demod

TUNER_SIF(for T2/C/S)

3.3K Ω

/TU_RESET1

/S2_RESET

LNB_OUT

IC2_SCL6 IC2_SDA6

Attenuator

LNB_TX

I2C_SCL4

I2C_SDA4

T2/C/S) IF_AGC

TU_CVBS(for

4. Tuner/CI Block Diagram

+1.8_TU +3.3V_TU +3.3V_D_Demod

IF_P

IF_N

LG Electronics 47LA71** — 10 [TONECTRL] diagram (page 67)
Fig. 103

[+3.3V_S2_DEMOD] 32

[+1.23V_S2_DEMOD] 30

[S2_F22_OUTPUT] 33

[LNB] 36

[S2_SCL] 34

[S2_SDA] 35

[SLC] 3

[SDA] 4

[ERROR] 16

[SYNC] 17

[VALID] 18

[MCLK] 19

[D0-7] 20-27

[T/C_DIF[P]] 10

[T/C_DIF[N]] 11

[+3.3V_TUNER] 5

[+.1.8V_TUNER] 7

TDSQ-

G501D

Page 68 of the LG Electronics 47LA71** user manual — LGE 2122
Page 68 · click to enlarge
Page 68
LG Electronics 47LA71** — #EV# diagram (page 68)
Fig. 104

LGE 2122

[MPXP, ADCINP_DEMOD, ADCINN_DEMOD]

[ADIN0_SRV, SOY1]

[PR1P, PB1P, Y1P]

[AIN1_L/R_AADC]

[AIN4_L_AADC]

[AIN4_R_AADC] COMP1/AV1/DVI_R_IN_SOC

[CVBS2P]

[CVBS3P] SC_CVBS_IN_SOC

[CVBS1P]

[PB0P]

[PR0P]

Parallel TS / ERROR,VAL,SYNC,CLK Parallel TS / ERROR,VAL,SYNC,CLK

COMP1/AV1/DVI_L_IN_SOC

COMP1_Y/AV1_CVBS_SOC

TUNER_SIF, IF_P/N

COMP1_Pb_SOC

COMP1_Pb_SOC

SC_L/R_IN_SOC

Jack Side SoC Side

SC_R/G/B_SOC

SC_FB_SOC

TU_CVBS

5. Video/Audio In Block Diagram

COMP1/AV1/DVI_R_IN

COMP1_Y/AV1_CVBS

COMP1/AV1/DVI_L_IN

TUNER_SIF, IF_P/N

COMP1_Pb

SC_CVBS_IN

COMP1_Pr

SC_ID/FB

SC_R/G/B

SC_L/R_IN

TU_CVBS

JK501

JK4600

SCART

Tuner

Page 69 of the LG Electronics 47LA71** user manual — [AIN1_L_AADC] [AIN1_R_AADC]
Page 69 · click to enlarge
Page 69
LG Electronics 47LA71** — #EV# diagram (page 69)
Fig. 105

6. Audio Out Block Diagram

LG Electronics 47LA71** — 6. Audio Out Block Diagram diagram (page 69)
Fig. 106 · 6. Audio Out Block Diagram
LG Electronics 47LA71** — 6. Audio Out Block Diagram diagram (page 69)
Fig. 107 · 6. Audio Out Block Diagram

SCART

IC6000 AZ4580MTR

DTV/MNT_L/R_OUT [AL1_ADAC] [AR1_ADAC]

SCART_L/Rout

COMP1/AV1/DVI_L_IN_SOC COMP1/AV1/DVI_R_IN_SOC

LPF

[AIN4_L_AADC] [AIN4_R_AADC]

OP AMP

Mute CTRL

(TR)

JK4600

JK501

DVB only

SCART_MUTE

SCART

AUD_MASTER_CLK [AOMCLK]

LG Electronics 47LA71** — SCART diagram (page 69)
Fig. 108

SC_L_IN / SC_R_IN

AUD_LRCH

LG Electronics 47LA71** — SC_L_IN / SC_R_IN diagram (page 69)
Fig. 109

[AIN1_L_AADC] [AIN1_R_AADC]

[AOSDATA0]

AUD_LRCK

[AOLRCK]

4P WAFER

AUD_SCK [AOBCK]

IC8101 Audio AMP

LPF

SPEAKER_L

JK4600

DVB only

I2C_SDA1

[STB_SDA]

NTP7513

LPF

SPEAKER_R

I2C_SCL1

[STB_SCL]

[OPCTRL4] AMP_RESET_N

WOOFER

LGE 2122

AMP_MUTE

Tuner

IC3000 MICOM

TUNER_SIF

TR BUF [MPXP]

SIDE_HP_MUTE

IC6100 TPA6138A2PWR

[AL0_ADAC] [AR0_ADAC]

HP_L/ROUT_MAIN

HP_L/ROUT_AMP

HEAD PHONE LPF

HP AMP

JK3700

SPDIF_OUT

[ASPDIF0]

JK3602

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 70 of the LG Electronics 47LA71** user manual — DDC_SCL_1_SOC
Page 70 · click to enlarge
Page 70

7. HDMI

LG Electronics 47LA71** — 7. HDMI diagram (page 70)
Fig. 110
LG Electronics 47LA71** — 7. HDMI diagram (page 70)
Fig. 111

DDC_SCL_1_SOC

DDC_SDA_1_SOC

HDMI_ARC

TMDS Link 8bits

HDMI1

DDC_SCL_2_JACK

DDC_SDA_2_JACK

CEC_REMOTE

LGE 2122

TMDS Link 8bits

HDMI2

I2C_SCL4

DDC_SCL_3_JACK

I2C_SDA4

DDC_SDA_3_JACK

SIL1292

TMDS Link 8bits

TMDS Link or MHL Link

HDMI3

5V_BUS OCP 5V_MHL

Q3001

HDMI_CEC

MHL_DET

X-tal 32.768kHz

RENESAS

WOL_CTL

MICOM

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 71 of the LG Electronics 47LA71** user manual — 8. Panel Interface Block Diagram
Page 71 · click to enlarge
Page 71
LG Electronics 47LA71** — #EV# diagram (page 71)
Fig. 112

8. Panel Interface Block Diagram

PANEL_VCC

(+12V)

VDD

PMIC TPS65178

H_VDD

Level Shift

TPS65198

VCOM_P

VCOM_N

LGE 2122

VCOM_LOOP

CLK1_I~CLK6_I

SWP CTRLP

TR/ Diode

VGH

SWN CTRLN

TR/ Diode

VGL

GIP_RST

VGL_I

VST

50Pin X 2

GMA4/GMA5/GAM7/GMA12/GMA14/ GMA15

EPI CH1 +/- EPI CH2 +/- EPI CH3 +/-

GMA1/GMA3/GAM9/GMA10/GMA16/GMA18

VCOM

VCOM_DYN VCOMLFB

VGH_EVEN/VGH_ODD

VGH_F/VGH_R

EPI Tx

EO GST GCLK MCLK

EPI_LOCK3

Block

Z_Out

VCOMRFB

EPI CH4 +/- EPI CH5 +/- EPI CH6 +/-

EPI_LOCK6_SOURCE EPI_LOCK6

GMA4/GMA5/GAM7/GMA12/GMA14/GMA15

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 72 of the LG Electronics 47LA71** user manual — 9. PMIC & Level Shift Bloc Diagram
Page 72 · click to enlarge
Page 72
LG Electronics 47LA71** — #EV# diagram (page 72)
Fig. 113

9. PMIC & Level Shift Bloc Diagram

PANEL_VCC

PMIC TPS65178

Vdd

Boost Converter

Buck 1 converter(VCC)

Buck 2 converter(Vcore)

Vcore

HVdd

Buck 3 converter(HVdd)

Level Shift

Buck 4 converter(VCC18)

TPS65198

SWN

TR/ Diode

VGL

Positive Charge Pump Controller

CTRLN

SWP

VGH

Negative Charge Pump Controller

TR/ Diode

CTRLP

GAM4/5/7/12/14/15

6-Ch Gamma Buffer(DAC output)

VCOM_P

VCOM_N

Vcom reference & gain

VCOM_LOOP

PMIC_RESET

Reset

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 73 of the LG Electronics 47LA71** user manual — 4Pin debugging wafer
Page 73 · click to enlarge
Page 73

10. USB / WIFI / M-REMOTE / UART

LG Electronics 47LA71** — 10. USB / WIFI / M-REMOTE / UART diagram (page 73)
Fig. 114

USB_DM1

USB1

LG Electronics 47LA71** — USB_DM1 diagram (page 73)
Fig. 115

[USB_DP_P2] [USB_DM_P2]

+5V_USB_1

USB_DP1

[GPIO43] [GPIO46] OCP

/USB_OCD1

USB_CTL1

USB_DM2

USB2

+5V_USB_2

[USB_DM_P1]

USB_DP2

[USB_DP_P1]

/USB_OCD2

[GPIO42] [TCON12]

USB_CTL2

OCP

USB3 USB_DM3

[USB_DM_P0]

+5V_USB_3

USB_DP3

[USB_DP_P0]

/USB_OCD3

[GPIO44] [ADIN2_SRV]

USB_CTL3

USB_WIFI WIFI_DM

[USB_DM_P3]

[USB_DP_P3]

WIFI_DP

[U1RX]

M_REMOTE_RX

LG Electronics 47LA71** — [USB_DP_P2] [USB_DM_P2] diagram (page 73)
Fig. 116

[U1TX]

M_REMOTE_TX

Motion Remote

RTS [ADIN4_SRV]

M_RFModule_RESET

Receiver

[OPCTRL49]

CTS

[OPCTRL50]

HDMI2

SOC_TX

[U0TX] [U0RX]

LG Electronics 47LA71** — [U1TX] diagram (page 73)
Fig. 117
LG Electronics 47LA71** — [U1TX] diagram (page 73)
Fig. 118

4Pin debugging wafer

SOC_RX

LGE 2122

HDMI3

RENESAS MICOM

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 74 of the LG Electronics 47LA71** user manual — 1 / 88
Page 74 · click to enlarge
Page 74

Interconnection - 1

47LA660S-ZA

[PCBs]

LG Electronics 47LA71** — Interconnection - 1 diagram (page 74)
Fig. 119 · Interconnection - 1

1 Main PCB

2 Power Board

3 Local key Assy

4 RF Assy

5 WIFI Assy

[Cables]

Main / LPB 24Pin + Local Dimming Cable

Main / Module EPI Cable 50& 50Pin

LED driver / PSU

IR 8Pin Cable

WiFi 6Pin + RF 8Pin Cable

LG Electronics 47LA71** — 1 Main PCB diagram (page 74)
Fig. 120 · 1 Main PCB

SPK Cable

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

1 / 88

Page 75 of the LG Electronics 47LA71** user manual — 2 / 88
Page 75 · click to enlarge
Page 75

Interconnection - 2

47LA660S-ZA

LG Electronics 47LA71** — Interconnection - 2 diagram (page 75)
Fig. 121 · Interconnection - 2

[PCBs]

6 IR Assy

[Cables]

IR to Local Key 3Pin Cable

IR to Logo Assy 4Pin Cable

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

2 / 88

Page 76 of the LG Electronics 47LA71** user manual — 3 / 88
Page 76 · click to enlarge
Page 76

Introductions of 13Y RF ass’y + Magic Remote control

1. System

2. Remote Buttons

3. MR13 Block Diagram

4. Function List

5. Pairing/Un-pairing Method

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

3 / 88

Page 77 of the LG Electronics 47LA71** user manual — 4 / 88
Page 77 · click to enlarge
Page 77

1. System

LG Electronics 47LA71** — 1. System diagram (page 77)
Fig. 122 · 1. System
LG Electronics 47LA71** — 1. System diagram (page 77)
Fig. 123 · 1. System

UART or USB

LG Electronics 47LA71** — UART or USB diagram (page 77)
Fig. 124 · UART or USB

RF

RF Receiver

TV

Remote

LG Electronics 47LA71** — RF diagram (page 77)
Fig. 125

Pairing Information Transmission (Send to TV after Paired)

  • Static Calibration Data (Bypass only)
  • Remote FW ver. (Save also in Receiver)
  • BD_ADDR (Save also in Receiver)
  • Pairing Information Transmission Sequence
  • When it is paired, the remote sends packets(pairing success, F/W version, BD_ADDR) to the receiver.
  • The receiver sends the pairing success packet to TV directly.
  • F/W version and BD_ADDR packets are just saved on the receiver.
  • The receiver sends F/W version or BD_ADDR packet to TV when it is required. Motion Data Transmission
  • Period : 7.5msec
  • Motion Data : gyro, accelerometer Voice Data Transmission
  • Period : 10msec
  • Voice sampling : 16khz 16bit

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

4 / 88

Page 78 of the LG Electronics 47LA71** user manual — 5 / 88
Page 78 · click to enlarge
Page 78

2. Remote Buttons (M4 vs. MR13)

LG Electronics 47LA71** — 2. Remote Buttons (M4 vs. MR13) diagram (page 78)
Fig. 126 · 2. Remote Buttons (M4 vs. MR13)
LG Electronics 47LA71** — 2. Remote Buttons (M4 vs. MR13) diagram (page 78)
Fig. 127 · 2. Remote Buttons (M4 vs. MR13)
LG Electronics 47LA71** — 2. Remote Buttons (M4 vs. MR13) diagram (page 78)
Fig. 128 · 2. Remote Buttons (M4 vs. MR13)
LG Electronics 47LA71** — 2. Remote Buttons (M4 vs. MR13) diagram (page 78)
Fig. 129 · 2. Remote Buttons (M4 vs. MR13)

BUTTON RF Unpaired

RF Paired

IR continuous

repeat ETC.

IR_CODE

RF_CODE

POWER 0x08 NONE Y IR only

POWER

POWER

BACK 0x28 0x8028 Y

SMART 0x7C 0x807C Y

↑

BACK HOME

← 0x07 0x8007 Y

→ 0x06 0x8006 Y

OK ← →

↑

BACK SMART

↑ 0x40 0x8040 Y

↓ 0x41 0x8041 Y

↓

OK ← →

OK 0x75 0x8044 Y

Phsical Buttons

↓

VOICE

VOICE 0xDE 0x808B Y = VOICE_START

3D 0xDC 0x80DC Y

3D Screen RMT

Screen RMT / Q.MENU 0xDE 0x80DE Y

Q.MENU

MUTE VOL CH

CH + 0x00 0x8000 Y

CH - 0x01 0x8001 Y

MUTE VOL CH

3D MYAPPS

VOL + 0x02 0x8002 Y

VOL - 0x03 0x8003 Y

MUTE 0x09 0x8009 Y

AUTO_WAKEUP X 0x800C

VOICE_START X 0x800A

Logical

VOICE_STOP X 0x800D

Buttons

POINT_START X 0x803E

M4 Remote

MR13 Remote

POINT_STOP X 0x803F

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

5 / 88

Page 79 of the LG Electronics 47LA71** user manual — 6 / 88
Page 79 · click to enlarge
Page 79

3. MR13 Block Diagram

LG Electronics 47LA71** — 3. MR13 Block Diagram diagram (page 79)
Fig. 130 · 3. MR13 Block Diagram

MPU-6150 (Gyro+ACC)

I2C ch1

IR Emitter1

Antenna

(Invensense)

512Kb (Serial F/M)

IR Emitter2 (Voice Scene IR)

BCM20702M (BROADCOM) Bluetooth 4.0

BCM20733M A2

(BROADCOM)

Bluetooth 3.0 Key Button

SPI

( 4 x 4 )

512Kbit (Serial Flash)

Voice

Antenna

I2S

Partron

WM8950 (Wolfson)

X-tal 20 MHz

X-tal 24 MHz

I2C ch2

MIC. (Knowles)

Codec(ADC )

Wheel Encoder

4-mode Only

UART

Power Management

AA x 2 Battery DC-DC Boost

2.8V LDO uP0108NEC5-28

2.8V LDO uP0108NEC5-28

TI TPS61097

Connector

SOT23-5

SC70

SC70

Bluetooth Remote control

Bluetooth Receiver

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

6 / 88

Page 80 of the LG Electronics 47LA71** user manual — 7 / 88
Page 80 · click to enlarge
Page 80

4. Function list

주요 Item IC Manufacturer Function

Voice Codec WM8950 Wolfson 16KHz Sampling of Audio data

Voice

MEMS Mic. SPU0414HR5H Knowles Sensing Voice

Gyro Sensor

Sensing angular velocity of X, Y, Z-axis

Motion Sensor

+ Accelerometer

MPU-6150 Invensense

Sensing device tilt (Pitch & Roll angle)

RF Antenna SDBTPTR3015 Partron

Remocon

RF

Wireless communication X-tal 24MHz Partron

+ Micom

RF + Micom BCM20733A2 Broadcom

DC-DC Converter TPS61097 TI Battery Boost up Regulator

LDO1 uP0108NEC5-28 uPI RF, Gyro, Accelerometer Power Supply

LDO2 uP0108NEC5-28 uPI Audio Codec, Mic. Power Supply

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

7 / 88

Page 81 of the LG Electronics 47LA71** user manual — 8 / 88
Page 81 · click to enlarge
Page 81

5. RF Pairing / Un-pairing Method

Method Description

  • When do pairing, the remote should make pairing request IR signal(0x75) to TV.
  • When TV receive the IR signal, it should send "pairing request packet" to the RF receiver.
  • After pairing success, the remote should blink LED for some time and TV send "pairing success packet" back to TV.
  • When remote try to unpairing, it doesn’t care about state of receiver(stand alone).

Method1

– If unpaired, just press "OK" button. – If paired, press "OK" button after

RF Pairing

unpairing. Method 2 (Repairing)

– Press “BACK" button for 5 sec.

  • When remote try to unpairing, it doesn’t care about state of receiver(stand alone).
  • After unpairing, all pairing information should be erased.
  • After unpairing, LED should be blinked for 3sec.
  • The remote just becomes to IR mode.

RF Unpairing Press “BACK" button and “SMART" button at the same time for 5 sec.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

8 / 88

Page 82 of the LG Electronics 47LA71** user manual — 9 / 88
Page 82 · click to enlarge
Page 82

Introductions of 13Y WIFI built in ass’y

1. Wi-Fi built in Ass’y feature 2. Wi-Fi built in Ass’y specification

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

9 / 88

Page 83 of the LG Electronics 47LA71** user manual — 10 / 88
Page 83 · click to enlarge
Page 83

WIFI Built in ass’y feature

Block diagram

LG Electronics 47LA71** — WIFI Built in ass’y feature diagram (page 83)
Fig. 131 · WIFI Built in ass’y feature
LG Electronics 47LA71** — WIFI Built in ass’y feature diagram (page 83)
Fig. 132 · WIFI Built in ass’y feature

USB DP, DN

DCDC EUP3010

Wafer

3.3V 1.2V

- Pin map

GND

WOL

6pin 1.25mm

3.3V 1.2V

PIN USB interface

2 DM

RX/TX

Switch DM3030

Antenna

3 DP

2.4G/5G

USB DP, DN

4 GND

BCM43236B

RX/TX

5 WOW

Switch DM3030

Antenna

Crystal

2.4G/5G

20MHz

6 NC

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

10 / 88

Page 84 of the LG Electronics 47LA71** user manual — 11 / 88
Page 84 · click to enlarge
Page 84

WIFI Built in ass’y Specification

LG Electronics 47LA71** — WIFI Built in ass’y Specification diagram (page 84)
Fig. 133 · WIFI Built in ass’y Specification
LG Electronics 47LA71** — WIFI Built in ass’y Specification diagram (page 84)
Fig. 134 · WIFI Built in ass’y Specification

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

11 / 88

Page 85 of the LG Electronics 47LA71** user manual — 12 / 88
Page 85 · click to enlarge
Page 85

Widevine & HDCP 2.0 & NETFLX

Contents

표지

1. Widevine?

2. HDCP 2.0 & NETFLIX?

3. DTCP?

4. Changed BOM

2012. 12. 08

LCD TV LCD TV R&D Lab / HW1 team

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

12 / 88

Page 86 of the LG Electronics 47LA71** user manual — 13 / 88
Page 86 · click to enlarge
Page 86

1. Widevine?

LG Electronics 47LA71** — 1. Widevine? diagram (page 86)
Fig. 135 · 1. Widevine?
LG Electronics 47LA71** — 1. Widevine? diagram (page 86)
Fig. 136 · 1. Widevine?

[Widevine] Widevine is the Solution(Library) offering Adaptive Streaming and DRM. In BBTV, when special CP do service, this module is required key. Currently CP which is requested to widevine, is typically Australian Bigpond Live and North American CinemaNow. Furthermore, because the future will be the spread of CP, widevine key download for the global model should be applied to production. (Because operation unique key should be downloaded for Widevine , Widevine key dowmload by NSU is impossible.)

LG Electronics 47LA71** — 1. Widevine? diagram (page 86)
Fig. 137 · 1. Widevine?
LG Electronics 47LA71** — 1. Widevine? diagram (page 86)
Fig. 138 · 1. Widevine?

[Widevine Key] Widevine Key is unique data stored TV for using Widevine.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

13 / 88

Page 87 of the LG Electronics 47LA71** user manual — 14 / 88
Page 87 · click to enlarge
Page 87

2. HDCP 2.0 & NETFLIX?

HDCP

LG Electronics 47LA71** — 2. HDCP 2.0 & NETFLIX? diagram (page 87)
Fig. 139

High-bandwidth Digital Content Protection

Protect high-value digital motion pictures, television programs and audio against unauthorized interception and copying between a digital set top box or digital video recorder and a digital TV or PC. Specification developed by Intel Corporation to protect digital entertainment across the DVI/HDMI interface.

Why HDCP2.0? HDCP revision 2.0 supports a broader range of wired and wireless interfaces.

Netflix the services maintain a huge selection of movies and latest releases and offer

DVD rentals via mail & online streaming.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

14 / 88

Page 88 of the LG Electronics 47LA71** user manual — 15 / 88
Page 88 · click to enlarge
Page 88

3. DTCP?

LG Electronics 47LA71** — 3. DTCP? diagram (page 88)
Fig. 140
LG Electronics 47LA71** — 3. DTCP? diagram (page 88)
Fig. 141

[DTCP] The Digital Transmission Content Protection Specification defines a cryptogrphic protocol for protecting audio/video entertainment content from unauthorized copying, intercepting, and tampering as it traverses digital transmission mechanisms such as a high-performance serial bus that conforms to the IEEE 1394-1995 standard. Only legitimate entertainment content delivered to a source device via another approved copy protection system (such as the DVD Content Scrambling System) will be protected by this protection system. [Three cryptographic Keys]

  • Authentication Key which is formed as a result of authentication and used to protect the exchange keys.
  • Exchage Key which is used to set up and protect content streams.
  • Content Key which is used to encrpt the content being exchanged.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

15 / 88

Page 89 of the LG Electronics 47LA71** user manual — 16 / 88
Page 89 · click to enlarge
Page 89

4. Changed BOM

As-Was Current

LG Electronics 47LA71** — 4. Changed BOM diagram (page 89)
Fig. 142 · 4. Changed BOM
LG Electronics 47LA71** — 4. Changed BOM diagram (page 89)
Fig. 143 · 4. Changed BOM

Changed Item : Separate HDCP check box. - HDCP 2.0 Tx - HDCP 2.0 Rx - HDCP 1.4 Rx

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

16 / 88

Page 90 of the LG Electronics 47LA71** user manual — 17 / 88
Page 90 · click to enlarge
Page 90

Contents of LCD TV Standard Repair Process

No. Error symptom (High category) Error symptom (Mid category) Page Remarks

No video/Normal audio 1

2 No video/No audio 2

3 Video error, video lag/stop, fail tunning 3, 4

A. Video error

4 Color error 5

5 Vertical/Horizontal bar, residual image, light spot, external device color error 6

No power 7

B. Power error

7 Off when on, off while viewing, power auto on/off 8

8 C. Audio error

No audio/Normal video 9

9 Wrecked audio/discontinuation/noise 10

No response in remote controller, key error, recording error, memory error 11

10 D. Function error

11 External device recognition error 12

12 E. Noise Circuit noise, mechanical noise 13

13 F. Exterior error Exterior defect 14

14 G. Network error Connection defect / Network speed low 15

First of all, Check whether there is SVC Bulletin in GCSC System for these model.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

17 / 88

Page 91 of the LG Electronics 47LA71** user manual — 18 / 88
Page 91 · click to enlarge
Page 91

Contents of LCD TV Standard Repair Process Detail Technical Manual

No. Error symptom Content Page Remarks

Check LCD back light with naked eye A1

2 LED driver B+ 24V measuring method A2

A. Video error_ No video/Normal audio

3 Check White Balance value A3

4 Power Board voltage measuring method A4

6 A. Video error_ No video/Video lag/stop

TUNER input signal strength checking method A6

7 LCD-TV Version checking method A7

LCD TV connection diagram A8

10 Tuner Checking Part A9

11 Check Link Cable (LVDS) reconnection condition

A. Video error_Color error

A10 A11

A10 : 32/37/42/47/55 A11 : 32 AUO

12 Adjustment Test pattern - ADJ Key A12

LCD TV connection diagram A8

14 Check Link Cable (LVDS) reconnection condition

A. Video error_Vertical/Horizontal bar, residual image, light spot

A10 A11

A10 : 32/37/42/47/55 A11 : 32 AUO

15 Adjustment Test pattern - ADJ Key A12

Exchange T-Con Board (1) A-1/5

17 Exchange T-Con Board (2) A-2/5

<Appendix> Defected Type caused by T-Con/ Inverter/ Module

18 Exchange LED driver Board (PSU) A-3/5 55” : driver board Other : PSU

19 Exchange Module itself (1) A-4/5

20 Exchange Module itself (2) A-5/5

Continue to the next page Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

18 / 88

Page 92 of the LG Electronics 47LA71** user manual — 19 / 88
Page 92 · click to enlarge
Page 92

Standard Repair Process

Established

A. Video error

Error symptom

date

2012. 12 .06

Revised date LCD TV

No video/ Normal audio

First of all, Check whether all of cables between board is inserted properly or not. (Main B/D↔ Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable,,,)

☞ A4 ☞ A1

No video Normal audio

Normal

Y

Check Back Light On with naked eye On Y

Check Power Board 12v,3.5v etc. Normal

Y

Replace T-con Board or module And Adjust VCOM

audio

voltage

N

N

N

☞ A28

Move to No video/No audio

☞ A2

Repair Power Board or parts Check Power Board 24v output

Normal voltage

Y Replace Inverter or module

End

N

Repair Power Board or parts

※ Precaution

☞ A7 & A3

Always check & record S/W Version and White Balance value before replacing the Main Board Replace Main Board Re-enter White Balance value

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

19 / 88

Page 93 of the LG Electronics 47LA71** user manual — 20 / 88
Page 93 · click to enlarge
Page 93

Standard Repair Process

Established

A. Video error

Error symptom

date

2012. 12 .06

Revised date LCD TV

No video/ No audio

☞ A4

Check various voltages of Power Board ( 3.5V,12V,20V or 24V…) No Video/ No audio

Check and replace MAIN B/D

Normal voltage?

Y

N End

Replace Power Board and repair parts

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

20 / 88

Page 94 of the LG Electronics 47LA71** user manual — 21 / 88
Page 94 · click to enlarge
Page 94

Standard Repair Process

A. Picture Problem

Established

Error symptom

2012. 12 .06

Revised date LCD TV

date

Picture broken/ Freezing

. By using Digital signal level meter . By using Diagnostics menu on OSD ( Menu→ Set up→ Support → Signal Test ) - Signal strength (Normal : over 50%) - Signal Quality (Normal: over 50%)

☞ A6

Check RF Signal level

Y

Check whether other equipments have problem or not.

Normal Signal?

(By connecting RF Cable at other equipment) → DVD Player ,Set-Top-Box, Different maker TV etc`

N

☞ A7

Check RF Cable

Normal Picture?

Y

Check S/W Version

SVC Bulletin?

N

Use Signal Test Check Signal status

Normal Picture?

Y

Connection 1. Reconnection 2. Install Booster

Close

N N

Y

S/W Upgrade

Check Tuner soldering

N

Normal Picture?

Contact with signal distributor

or broadcaster (Cable or Air)

Normal Picture?

N

Y

Replace Main B/D

Y

Close

Close

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

21 / 88

Page 95 of the LG Electronics 47LA71** user manual — 22 / 88
Page 95 · click to enlarge
Page 95

Standard Repair Process

A. Picture Problem (DVB-S/S2)

Established

Error symptom

2012. 12 .06

Revised date LCD TV

date

Tuning fail, Picture broken/ Freezing

☞ A6

Check RF signal cable (DVB satellite signal or not) Check whether other equipments have problem or not. (By connecting RF Cable at other equipment) → Set-Top-Box, Different maker TV etc

Check RF Signal level

☞ A7

Check satellite setting. - Check LNB frequency. - Check satellite - Check Satellite connection (DiSEqC, motor, etc…)

Y N

Y

Normal Signal?

Normal setting?

Check S/W Version

SVC Bulletin?

Check Tuner soldering

Replace Main B/D

N

N

Y

S/W Upgrade

Contact with signal distributor

Change satellite setting (match with installed ANT)

N

Normal Picture?

or broadcaster

(Cable or Air)

Y

N

Normal Picture?

Close

Close

Y

Close

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

22 / 88

Page 96 of the LG Electronics 47LA71** user manual — 23 / 88
Page 96 · click to enlarge
Page 96

Standard Repair Process

Established

A. Video error

Error symptom

date

2012. 12 .06

Revised date LCD TV

Color error

☞ A8

☞ A10/ A11

※ Check and replace Link Cable (LVDS) and contact condition

Y

Check color by input -External Input -COMPONENT -RGB -HDMI/DVI

Y

Y

Color error?

Replace Main B/D Color error?

Color error?

Replace module

N

N

N

Check error color input mode

End

Check Test pattern ☞ A12

Check external device and cable

External Input/

Y External device

Component

/Cable normal

Replace Main B/D

error

N

Request repair

for external device/cable

N

Y External device

RGB/ HDMI/DVI

Check external device and cable

Replace Main B/D

/Cable normal

error

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

23 / 88

Page 97 of the LG Electronics 47LA71** user manual — 24 / 88
Page 97 · click to enlarge
Page 97

Standard Repair Process

A. Video error

Established

2012. 12 .06

Error symptom

date

Revised date LCD TV

Vertical / Horizontal bar, residual image, light spot, external device color error

Vertical/Horizontal bar, residual image, light spot

Replace Module

☞ A8 ☞ A10/ A11

N

Check color condition by input -External Input -Component -RGB -HDMI/DVI

☞ A28

Y Check external device connection condition

Check and replace Link Cable Normal?

Y

N Screen normal? Replace Main B/D (adjust VCOM)

Screen normal?

Screen normal?

N

For LGD panel

Y

N

Y

Request repair for external device

Replace Main B/D

Replace module

End

End

☞ A12

For other panel

Check Test pattern

External device screen error-Color error

Check screen condition by input -External Input -Component -RGB -HDMI/DVI

N Check version

External

Check S/W Version

Connect other external device and cable (Check normal operation of External Input, Component, RGB and HDMI/DVI by connecting Jig, pattern Generator ,Set-top Box etc.

Input

N

error

Replace Main B/D Screen normal?

Y

Component

Y

S/W Upgrade

error

Request repair for external device

RGB error

Y

Connect other external device and cable (Check normal operation of External Input, Component, RGB and HDMI/DVI by connecting Jig, pattern Generator ,Set-top Box etc.

N Normal screen?

Replace Main B/D Screen normal?

N

Y

HDMI/

DVI

End

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

24 / 88

Page 98 of the LG Electronics 47LA71** user manual — 25 / 88
Page 98 · click to enlarge
Page 98

Standard Repair Process

B. Power error

Established

2012. 12 .06

Revised date LCD TV

Error symptom

date

No power

☞ A17

☞ A19

Y

DC Power on by pressing Power Key On Remote control

N Normal operation?

Replace Power B/D

Check Power LED

Power LED

Check Power On ‘”High”

Y OK?

On?

. Stand-By: Red . Operating: white

N

Y

Check Power cord was inserted properly

Replace Main B/D

☞ A4

N

Measure voltage of each output of Power B/D

Normal?

Y

Y

※ Close

Y Normal voltage?

Replace Main B/D

Y Normal voltage?

Check ST-BY 3.5V

N

☞ A18

Replace Power B/D

N

Replace Power B/D

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

25 / 88

Page 99 of the LG Electronics 47LA71** user manual — 26 / 88
Page 99 · click to enlarge
Page 99

Standard Repair Process

B. Power error

Established

2012. 12 .06

Error symptom

date

Revised date LCD TV

Off when on, off while viewing, power auto on/off

Check outlet

☞ A22

N

Y Normal? End

Check A/C cord

Error?

Check Power Off Mode

Replace Main B/D CPU Abnormal

N

Check for all 3phase power out

Y

Abnormal

Replace Power B/D

Fix A/C cord & Outlet and check each 3 phase out

☞ A19

(If Power Off mode is not displayed) Check Power B/D voltage

Replace Main B/D Normal voltage?

Y

N

※ Caution Check and fix exterior of Power B/D Part

Replace Power B/D

* Please refer to the all cases which can be displayed on power off mode.

Status Power off List Explanation

"POWEROFF_REMOTEKEY" Power off by REMOTE CONTROL "POWEROFF_OFFTIMER" Power off by OFF TIMER "POWEROFF_SLEEPTIMER" Power off by SLEEP TIMER "POWEROFF_INSTOP" Power off by INSTOP KEY "POWEROFF_AUTOOFF" Power off by AUTO OFF "POWEROFF_ONTIMER" Power off by ON TIMER "POWEROFF_RS232C" Power off by RS232C "POWEROFF_RESREC" Power off by Reservated Record "POWEROFF_RECEND" Power off by End of Recording "POWEROFF_SWDOWN" Power off by S/W Download "POWEROFF_UNKNOWN" Power off by unknown status except listed case

Normal

Abnormal "POWEROFF_ABNORMAL1" Power off by abnormal status except CPU trouble "POWEROFF_CPUABNORMAL" Power off by CPU Abnormal

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

26 / 88

Page 100 of the LG Electronics 47LA71** user manual — 27 / 88
Page 100 · click to enlarge
Page 100

Standard Repair Process

Established

C. Audio error

2012. 12 .06

Error symptom

date

Revised date LCD TV

No audio/ Normal video

☞ A24 ☞ A25

Check user menu > Speaker off

Check audio B+ 24V of Power Board Normal voltage

No audio Screen normal

N

Y

Off

Y

N

Cancel OFF

Replace Power Board and repair parts

Check Speaker disconnection

N

Disconnection

Replace MAIN Board End

Y

Replace Speaker

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

27 / 88

Page 101 of the LG Electronics 47LA71** user manual — 28 / 88
Page 101 · click to enlarge
Page 101

Standard Repair Process

C. Audio error

Established

Error symptom

2012. 12 .06

Revised date LCD TV

date

Wrecked audio/ discontinuation/noise

→ abnormal audio/discontinuation/noise is same after “Check input signal” compared to No audio

☞ A25

Wrecked audio/ Discontinuation/

Check and replace speaker and connector

Check audio B+ Voltage (24V)

Noise for

Check input signal -RF -External Input signal

all audio

Y

Y

Signal normal?

Wrecked audio/ Discontinuation/

Normal voltage?

Replace Main B/D N

Noise only

for D-TV

N

Wrecked audio/ Discontinuation/

Replace Power B/D

Noise only

for Analog

(When RF signal is not received) Request repair to external cable/ANT provider

Replace Main B/D

End

Wrecked audio/ Discontinuation/

Noise only for External Input

(In case of External Input signal error) Check and fix external device

N

Connect and check other external device

Normal

audio?

Y

Check and fix external device

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

28 / 88

Page 102 of the LG Electronics 47LA71** user manual — 29 / 88
Page 102 · click to enlarge
Page 102

Standard Repair Process

D. General Function Problem

Established

Error symptom

2012. 12 .06

Revised date LCD TV

date

Remote control & Local switch checking

1. Remote control(R/C) operating error

Replace Main B/D

Y ☞ A27

☞ A27

☞ A27

Check & Repair Cable connection Connector solder

N

Y

Check R/C itself

Normal operating?

Y

Normal operating?

Check B+ 3.5V

Normal Voltage?

Check IR Output signal

Normal Signal?

Operation

On Main B/D

N

N

N

Y

☞ A4

Check R/C Operating

Check & Replace

Close

Repair/Replace

Check 3.5v on Power B/D

When turn off light

Baterry of R/C

IR B/D

Replace Power B/D or

in room

Replace Main B/D (Power B/D don’t have problem)

If R/C operate, Explain the customer

Normal operating?

Close

cause is interference

from light in room.

N

Replace R/C

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

29 / 88

Page 103 of the LG Electronics 47LA71** user manual — 30 / 88
Page 103 · click to enlarge
Page 103

Standard Repair Process

D. Function error

Established

Error symptom

2012. 12 .06

Revised date LCD TV

date

External device recognition error

Y

Check technical information - Fix information - S/W Version

Check input signal

External Input and

Signal input?

Technical information?

N

Component Recognition error

Replace Main B/D

N

Y

RGB,HDMI/ DVI, Optical Recognition error

Check and fix external device/cable

Replace Main B/D Fix in accordance with technical

information

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

30 / 88

Page 104 of the LG Electronics 47LA71** user manual — 31 / 88
Page 104 · click to enlarge
Page 104

Standard Repair Process

E. Noise

Established

Error symptom

2012. 12 .06

Revised date LCD TV

date

Circuit noise, mechanical noise

Replace PSU(with LED driver)

Check location of noise Identify noise type

Circuit

OR

noise

Replace LED driver

Mechanical

Check location of noise

noise

※ When the nose is severe, replace the module (For models with fix information, upgrade the S/W or provide the description) OR

※ Mechanical noise is a natural phenomenon, and apply the 1st level description. When the customer does not agree, apply the process by stage. ※ Describe the basis of the description in “Part related to nose” in the Owner’s Manual.

※ If there is a “Tak Tak” noise from the cabinet, refer to the KMS fix information and then proceed as shown in the solution manual (For models without any fix information, provide the description)

OR

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

31 / 88

Page 105 of the LG Electronics 47LA71** user manual — 32 / 88
Page 105 · click to enlarge
Page 105

Standard Repair Process

F. Exterior defect

Established

Error symptom

2012. 12 .06

Revised date LCD TV

date

Exterior defect

Replace module Zoom part with exterior damage

Module damage

Adjust VCOM

☞ A28

Cabinet damage Replace cabinet

Replace remote controller Remote controller

damage

Stand

dent Replace stand

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

32 / 88

Page 106 of the LG Electronics 47LA71** user manual — 33 / 88
Page 106 · click to enlarge
Page 106

Standard Repair Process

G. Network Error

Established

2012. 12 .06

Revised date LCD TV

Error symptom

date

Exterior defect

Check Wired ethernet cable connection Check whether AP has a probelm or not. Setting Network Networ Status

Check Network status

☞ A7 Check Network connection Case1 WiFi . - Check AP status Case2 Wired - Check ethernet Port

Normal Signal?

Y N

Normal setting?

Y

Check S/W Version

SVC Bulletin?

Check Wired, Wifi status (Cable / sub Assy)

Replace Main B/D

N

Y

N

S/W Upgrade

Check connection with AP or internet

Try to new network connection (match with AP and ether setting)

N

Normal Picture?

(WiFi = AP) (Wired = ethernet

port)

Y

N

Normal Picture?

Close

Close

Y

Close

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

33 / 88

Page 107 of the LG Electronics 47LA71** user manual — 34 / 88
Page 107 · click to enlarge
Page 107

Standard Repair Process

G. CI+ Competibility Error

Established

Error symptom

2012. 12 .06

Revised date LCD TV

date

Exterior defect

Check defect CI slot pin Check it’s worked CI+ 1.2 or 1.3 Setting Antenna CI information

Check CI CAM status

Y N

Read Information?

Check status of CI+ Key in the In-start menu

Is there CI+ key?

Y

Check CAM S/W

SVC Bulletin?

Check Wired, Wifi status (Cable / sub Assy)

Replace Main B/D

Version

N

N

Y

CAM S/W Upgrade

By OTA

Check damage of CI slot pin

Replace Main B/D

Or damage of CI CAM

N

Or Download

Normal Picture?

CI+ Key

Y

Close

Close

Old version of CI+ 1.2 CAM is not worked at the TV that is supported CI+ 1.3 Check SVC Bulletin

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

34 / 88

Page 108 of the LG Electronics 47LA71** user manual — 35 / 88
Page 108 · click to enlarge
Page 108

Contents of LCD TV Standard Repair Process Detail Technical Manual

Continued from previous page

No. Error symptom Content Page Remarks

Check front display LED A17

22 Check power input Voltage & ST-BY 3.5V A18

23 Checking method when power is ON A19

B. Power error_No power

24 POWER BOARD voltage measuring method A5

26 B. Power error_Off when on, off while viewing POWER OFF MODE checking method A22

27 B. Power error_Off when on, off while viewing POWER BOARD PIN voltage checking method A19

Checking method in menu when there is no audio A24

C. Audio error_No audio/Normal video

29 Voltage and speaker checking method when there is no audio A25

30 C. Audio error_Wrecked audio/discontinuation

Voltage and speaker checking method in case of audio error A25

31 D. Function error_ No response in remote controller, key error Remote controller operation checking method A27

32 D. VCOM Adjustment Sequence of the Vcom adjustment A28

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

35 / 88

Page 109 of the LG Electronics 47LA71** user manual — 36 / 88
Page 109 · click to enlarge
Page 109

Standard Repair Process Detail Technical Manual

Error symptom

A. Video error_No video/Normal audio

Established

2012. 12 .06

Content LCD TV

date Revised

A4

Check White Balance value

date

<ALL MODELS>

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 109)
Fig. 144 · Standard Repair Process Detail Technical Manual
LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 109)
Fig. 145 · Standard Repair Process Detail Technical Manual

Entry method 1. Press the ADJ button on the remote controller for adjustment. 2. Enter into White Balance of item 6. 3. After recording the R, G, B (GAIN, Cut) value of Color Temp (Cool/Medium/Warm), re- enter the value after replacing the MAIN BOARD.

Entry method 1. Press the ADJ button on the remote controller for adjustment. 2. Enter into White Balance of item 10. 3. After recording the R, G, B (GAIN, Cut) value of Color Temp (Cool/Medium/Warm), re- enter the value after replacing the MAIN BOARD.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

36 / 88

Page 110 of the LG Electronics 47LA71** user manual — 37 / 88
Page 110 · click to enlarge
Page 110

Standard Repair Process Detail Technical Manual

Error symptom

A. Video error_No video/ Audio

Established

2012. 12 .06

Content LCD TV

date Revised

Power Board voltage measuring method

A5

date

Check the DC 24V, 12V, 3.5V.

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 110)
Fig. 146 · Standard Repair Process Detail Technical Manual

24 Pin (Power Board ↔ Main Board)

SMAW200-H24S

1 Power on 2 Inverter On/off

3 3.5V 4 PWM Dim #1

5 3.5V 6 PWM Dim #2

7 GND 8 GND

9 24V 10 24V

11 GND 12 GND

13 12V 14 12V

15 12V 16 24V

17 GND 18 GND

19 GND 20 GND

21 GND 22 L/DIMO_VS

23 L/DIM0_MOSI 24 L/DIM0_SCLK

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

37 / 88

Page 111 of the LG Electronics 47LA71** user manual — 38 / 88
Page 111 · click to enlarge
Page 111

Standard Repair Process Detail Technical Manual

Error symptom

A. Video error_Video error, video lag/stop

Established

2012. 12 .06

Content LCD TV

date Revised

TUNER input signal strength checking method

A6

date

<ALL MODELS>

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 111)
Fig. 147 · Standard Repair Process Detail Technical Manual

MENU support signal test select channel

LG Electronics 47LA71** — MENU support signal test select channel diagram (page 111)
Fig. 148 · MENU support signal test select channel

When the signal is strong, use the attenuator (-10dB, -15dB, -20dB etc.)

LG Electronics 47LA71** — When the signal is strong, use the attenuator (-10dB, -15dB, -20dB etc.) diagram (page 111)
Fig. 149 · When the signal is strong, use the attenuator (-10dB…

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

38 / 88

Page 112 of the LG Electronics 47LA71** user manual — 39 / 88
Page 112 · click to enlarge
Page 112

Standard Repair Process Detail Technical Manual

Error symptom

A. Video error_Video error, video lag/stop

Established

2012. 12 .06

Content LCD TV

date Revised

LCD-TV Version checking method

A7

date

<ALL MODELS>

1. Checking method for remote controller for adjustment

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 112)
Fig. 150 · Standard Repair Process Detail Technical Manual

Version

LG Electronics 47LA71** — Version diagram (page 112)
Fig. 151 · Version

Press the IN-START with the remote controller for adjustment

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

39 / 88

Page 113 of the LG Electronics 47LA71** user manual — 40 / 88
Page 113 · click to enlarge
Page 113

Standard Repair Process Detail Technical Manual

Error symptom

A. Video error _Vertical/Horizontal bar, residual

Established

2012. 12 .06

Content LCD TV

image, light spot

date Revised

LCD TV connection diagram (1)

date

A8

<ALL MODELS>

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 113)
Fig. 152 · Standard Repair Process Detail Technical Manual

As the part connecting to the external input, check the screen condition by signal

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

40 / 88

Page 114 of the LG Electronics 47LA71** user manual — 41 / 88
Page 114 · click to enlarge
Page 114

Standard Repair Process Detail Technical Manual

Error symptom

A. Video error_Video error, video lag/stop

Established

2012. 12 .06

Content LCD TV

date Revised

TUNER checking part

A9

date

<ALL MODELS>

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 114)
Fig. 153 · Standard Repair Process Detail Technical Manual

Checking method: 1. Check the signal strength or check whether the screen is normal when the external device is connected. 2. After measuring each voltage from power supply, finally replace the MAIN BOARD.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

41 / 88

Page 115 of the LG Electronics 47LA71** user manual — 42 / 88
Page 115 · click to enlarge
Page 115

Standard Repair Process Detail Technical Manual

Error symptom

A. Video error_Color error

Established

2012. 12 .06

Content LCD TV

date Revised

Adjustment Test pattern - ADJ Key

A12

date

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 115)
Fig. 154 · Standard Repair Process Detail Technical Manual
LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 115)
Fig. 155 · Standard Repair Process Detail Technical Manual
LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 115)
Fig. 156 · Standard Repair Process Detail Technical Manual
LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 115)
Fig. 157 · Standard Repair Process Detail Technical Manual
LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 115)
Fig. 158 · Standard Repair Process Detail Technical Manual
LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 115)
Fig. 159 · Standard Repair Process Detail Technical Manual
LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 115)
Fig. 160 · Standard Repair Process Detail Technical Manual

You can view 6 types of patterns using the ADJ Key Checking item : 1. Defective pixel 2. Residual image 3. MODULE error (ADD-BAR,SCAN BAR..) 4.Video error (Classification of MODULE or Main-B/D!)

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

42 / 88

Page 116 of the LG Electronics 47LA71** user manual — 43 / 88
Page 116 · click to enlarge
Page 116

Appendix : Exchange EPI Cable or Main B/D (1)

LG Electronics 47LA71** — Appendix : Exchange EPI Cable or Main B/D (1) diagram (page 116)
Fig. 161 · Appendix : Exchange EPI Cable or Main B/D (1)

Solder defect, CNT Broken

Solder defect, CNT Broken Solder defect, CNT Broken

Solder defect, CNT Broken Solder defect, CNT Broken Abnormal Power Section

T-Con Defect, CNT Broken T-Con Defect, CNT Broken T-Con Defect, CNT Broken

Solder defect, Short/Crack Abnormal Power Section Solder defect, Short/Crack

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

43 / 88

Page 117 of the LG Electronics 47LA71** user manual — 44 / 88
Page 117 · click to enlarge
Page 117

Appendix : Exchange EPI Cable or Main B/D (2)

LG Electronics 47LA71** — Appendix : Exchange EPI Cable or Main B/D (2) diagram (page 117)
Fig. 162 · Appendix : Exchange EPI Cable or Main B/D (2)

Abnormal Power Section Solder defect, Short/Crack Abnormal Power Section

LG Electronics 47LA71** — Abnormal Power Section Solder defect, Short/Crack Abnormal Power Section diagram (page 117)
Fig. 163 · Abnormal Power Section Solder defect, Short/Crack Ab…

Solder defect, Short/Crack Fuse Open, Abnormal power section

Abnormal Display

LG Electronics 47LA71** — Solder defect, Short/Crack Fuse Open, Abnormal power section diagram (page 117)
Fig. 164 · Solder defect, Short/Crack Fuse Open, Abnormal power…
LG Electronics 47LA71** — Solder defect, Short/Crack Fuse Open, Abnormal power section diagram (page 117)
Fig. 165 · Solder defect, Short/Crack Fuse Open, Abnormal power…
LG Electronics 47LA71** — Solder defect, Short/Crack Fuse Open, Abnormal power section diagram (page 117)
Fig. 166 · Solder defect, Short/Crack Fuse Open, Abnormal power…

Noise GRADATION

GRADATION

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

44 / 88

Page 118 of the LG Electronics 47LA71** user manual — 45 / 88
Page 118 · click to enlarge
Page 118

Appendix : Exchange LPB(LED driver)

LG Electronics 47LA71** — Appendix : Exchange LPB(LED driver) diagram (page 118)
Fig. 167 · Appendix : Exchange LPB(LED driver)

No Light Dim Light

Dim Light Dim Light

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

45 / 88

Page 119 of the LG Electronics 47LA71** user manual — 46 / 88
Page 119 · click to enlarge
Page 119

Appendix : Exchange the Module (1)

LG Electronics 47LA71** — Appendix : Exchange the Module (1) diagram (page 119)
Fig. 168 · Appendix : Exchange the Module (1)

Panel Mura, Light leakage Press damage

Panel Mura, Light leakage

LG Electronics 47LA71** — Panel Mura, Light leakage Press damage diagram (page 119)
Fig. 169 · Panel Mura, Light leakage Press damage

Crosstalk Crosstalk Press damage

LG Electronics 47LA71** — Crosstalk Crosstalk Press damage diagram (page 119)
Fig. 170 · Crosstalk Crosstalk Press damage

Un-repairable Cases In this case please exchange the module.

Press damage

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

46 / 88

Page 120 of the LG Electronics 47LA71** user manual — 47 / 88
Page 120 · click to enlarge
Page 120

Appendix : Exchange the Module (2)

LG Electronics 47LA71** — Appendix : Exchange the Module (2) diagram (page 120)
Fig. 171 · Appendix : Exchange the Module (2)

Vertical Line Source TAB IC Defect

Vertical Block Source TAB IC Defect

Vertical Block Source TAB IC Defect

Horizontal Block Gate TAB IC Defect

Horizontal Block Gate TAB IC Defect

Horizontal line Gate TAB IC Defect

Gate TAB IC Defect Gate TAB IC Defect

LG Electronics 47LA71** — Vertical Line Source TAB IC Defect diagram (page 120)
Fig. 172 · Vertical Line Source TAB IC Defect

Un-repairable Cases In this case please exchange the module.

Gate TAB IC Defect Horizontal Block Gate TAB IC Defect

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

47 / 88

Page 121 of the LG Electronics 47LA71** user manual — 48 / 88
Page 121 · click to enlarge
Page 121

Standard Repair Process Detail Technical Manual

Error symptom

B. Power error _No power

Established

2012. 12 .06

Content LCD TV

date Revised

Check front display LED

A17

date

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 121)
Fig. 173 · Standard Repair Process Detail Technical Manual

You can set the LG Logo Light to on or off by selecting OPTION

in the main menus.

Front LOGO LED control in the status of ST-BY Condition: Menu Option LG Logo Light Brightness(OFF,LOW,MIDDLE,HIGH)

Front LOGO LED control in the status of Power On Condition: Menu Option LG Logo Light Duration(off, off after10min)

LOGO LED

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

48 / 88

Page 122 of the LG Electronics 47LA71** user manual — 49 / 88
Page 122 · click to enlarge
Page 122

Standard Repair Process Detail Technical Manual

Error symptom

B. Power error _No power

Established

2012. 12 .06

Content LCD TV

date Revised

Check power input voltage and ST-BY 3.5V

A18

date

For ’10 models, there is no voltage out for st-by purpose. When st-by, only 3.5V is normally on.

Check the DC 24V, 12V, 3.5V.

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 122)
Fig. 174 · Standard Repair Process Detail Technical Manual

24 Pin (Power Board ↔ Main Board)

SMAW200-H24S

1 Power on 2 Inverter On/off

3 3.5V 4 PWM Dim #1

5 3.5V 6 PWM Dim #2

7 GND 8 GND

9 24V 10 24V

11 GND 12 GND

13 12V 14 12V

15 12V 16 24V

17 GND 18 GND

19 GND 20 GND

21 GND 22 L/DIMO_VS

23 L/DIM0_MOSI 24 L/DIM0_SCLK

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

49 / 88

Page 123 of the LG Electronics 47LA71** user manual — 50 / 88
Page 123 · click to enlarge
Page 123

Standard Repair Process Detail Technical Manual

Error symptom

B. Power error _No power

Established

2012. 12 .06

Content LCD TV

date Revised

Checking method when power is ON

A19

date

Check “power on” pin is high

24 Pin (Power Board ↔ Main Board)

SMAW200-H24S

1 Power on 2 Inverter On/off

3 3.5V 4 PWM Dim #1

5 3.5V 6 PWM Dim #2

7 GND 8 GND

9 24V 10 24V

11 GND 12 GND

13 12V 14 12V

15 12V 16 24V

17 GND 18 GND

19 GND 20 GND

21 GND 22 L/DIMO_VS

23 L/DIM0_MOSI 24 L/DIM0_SCLK

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

50 / 88

Page 124 of the LG Electronics 47LA71** user manual — 51 / 88
Page 124 · click to enlarge
Page 124

Standard Repair Process Detail Technical Manual

Error symptom

B. Power error _Off when on, off whiling viewing

Established

2012. 12 .06

Content LCD TV

date Revised

POWER OFF MODE checking method

A22

date

<ALL MODELS>

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 124)
Fig. 175 · Standard Repair Process Detail Technical Manual

Entry method 1. Press the IN-START button of the remote controller for adjustment 2. Check the entry into adjustment item 3

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

51 / 88

Page 125 of the LG Electronics 47LA71** user manual — 52 / 88
Page 125 · click to enlarge
Page 125

Standard Repair Process Detail Technical Manual

Error symptom

C. Audio error_No audio/Normal video

Established

2012. 12 .06

Content LCD TV

date Revised

Checking method in menu when there is no audio

A24

date

<ALL MODELS>

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 125)
Fig. 176 · Standard Repair Process Detail Technical Manual

Checking method 1. Press the MENU button on the remote controller 2. Select the SOUND function of the Menu 3. Change TV Sound Out to TV Speaker

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

52 / 88

Page 126 of the LG Electronics 47LA71** user manual — 53 / 88
Page 126 · click to enlarge
Page 126

Standard Repair Process Detail Technical Manual

Error symptom

C. Audio error_No audio/Normal video

Established

2012. 12 .06

Content LCD TV

date Revised

Voltage and speaker checking method when there is no audio

A25

date

<ALL MODELS>

24 Pin (Power Board ↔ Main Board)

①

SMAW200-H24S

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 126)
Fig. 177 · Standard Repair Process Detail Technical Manual

1 Power on 2 Inverter On/off

3 3.5V 4 PWM Dim #1

5 3.5V 6 PWM Dim #2

7 GND 8 GND

②

②

9 24V 10 24V

11 GND 12 GND

13 12V 14 12V

15 12V 16 24V

③

17 GND 18 GND

19 GND 20 GND

21 GND 22 L/DIMO_VS

23 L/DIM0_MOSI 24 L/DIM0_SCLK

Checking order when there is no audio

① Check the contact condition of or 24V connector of Main Board

② Measure the 24V input voltage supplied from Power Board (If there is no input voltage, remove and check the connector)

③ Connect the tester RX1 to the speaker terminal and if you hear the Chik Chik sound when you touch the GND and output terminal, the speaker is normal.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

53 / 88

Page 127 of the LG Electronics 47LA71** user manual — 54 / 88
Page 127 · click to enlarge
Page 127

Standard Repair Process Detail Technical Manual

Error symptom

D. Function error_ No response in remote controller, key error

Established

2012. 12 .06

Content LCD TV

date Revised

A27

Remote controller operation checking method

date

<ALL MODELS>

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 127)
Fig. 178 · Standard Repair Process Detail Technical Manual

P4101 1 GND 2 KEY1 3 KEY2 4 +3.5V_ST 5 GND 6 LOGO/LED_R 7 IR 8 GND

LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 127)
Fig. 179 · Standard Repair Process Detail Technical Manual

③

④

②

①

Checking order 1, 2. Check IR cable condition between IR & Main board. 3. Check the st-by 3.5V on the terminal 4. 4. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog Tester needle moves slowly, and defective when it does not move at all.

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

54 / 88

Page 128 of the LG Electronics 47LA71** user manual — 55 / 88
Page 128 · click to enlarge
Page 128

Standard Repair Process Detail Technical Manual

Error symptom

D. VCOM Adjustment

Established

2012. 12 .06

Content LCD TV

date Revised

Sequence of the Vcom adjustment

A28

date

  • 1. Case
  • LCD module change
  • T-Con board change 2. Equipment
  • Service Remote controller 3. Adjust sequence
  • Press the ‘adj’ key
  • select V-COM
  • As pushing the right or the left button on the remote controller, And find the V-COM value Which is no or minimized the Flicker. (If there is no flicker at default value, Press the exit key and finish the VCOM adjustment.)
  • Push the OK key to store the value. Then the message “Saving OK” is pop.
  • Press the exit key to finish V-COM adjustment.
LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 128)
Fig. 180 · Standard Repair Process Detail Technical Manual
LG Electronics 47LA71** — Standard Repair Process Detail Technical Manual diagram (page 128)
Fig. 181 · Standard Repair Process Detail Technical Manual

Copyright © 2013 LG Electronics. Inc. All rights reserved. Only for training and service purposes

55 / 88

Ask about the LG Electronics 47LA71**

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LG Electronics 47LA71**

Be the first to ask — other owners or our team will answer.

Original document

LG Electronics 47LA71** manual PDF

128 pages·11.8 MB·Flat Panel Television·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…