EN
LG logo
Official user manual

LG Electronics 463

53 pages·7.2 MB·Flat Panel Television·PDF·ENDEFRITNLJA
LG Electronics 463
Table of Contents 1 sections #EV# ShowHide
Page 1 of the LG Electronics 463 user manual — Printed in Korea P/NO : MFL67360712 (1203-REV00)
Page 1 · click to enlarge
Page 1
LG Electronics 463 diagram (page 1)
Fig. 1

Internal Use Only

North/Latin America http://aic.lgservice.com Europe/Africa http://eic.lgservice.com Asia/Oceania http://biz.lgservice.com

LCD TV SERVICE MANUAL

CHASSIS : LD21C MODEL : 32CS460/460S/460T/463/465 MODEL : 32CS460/460S/460T/463/465-ZA

LG Electronics 463 — Internal Use Only diagram (page 1)
Fig. 2 · Internal Use Only
LG Electronics 463 — Internal Use Only diagram (page 1)
Fig. 3 · Internal Use Only

Printed in Korea P/NO : MFL67360712 (1203-REV00)

Page 2 of the LG Electronics 463 user manual — CONTENTS
Page 2 · click to enlarge
Page 2

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ......................................................................... 3

SERVICING PRECAUTIONS ................................................................... 4

SPECIFICATION ....................................................................................... 6

ADJUSTMENT INSTRUCTION .............................................................. 10

BLOCK DIAGRAM ................................................................................. 16

EXPLODED VIEW .................................................................................. 19

SCHEMATIC CIRCUIT DIAGRAM

- 2 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 3 of the LG Electronics 463 user manual — Before returning the receiver to the customer,
Page 3 · click to enlarge
Page 3

SAFETY PRECAUTIONS

LG Electronics 463 — SAFETY PRECAUTIONS diagram (page 3)
Fig. 4

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.

An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.

Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5 mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.

It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB.

Leakage Current Hot Check circuit

Keep wires away from high voltage or high temperature parts.

LG Electronics 463 — Leakage Current Hot Check circuit diagram (page 3)
Fig. 5 · Leakage Current Hot Check circuit

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.

Leakage Current Cold Check(Antenna Cold Check) With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 MΩ and 5.2 MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.

- 3 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 4 of the LG Electronics 463 user manual — a. Removing or reinstalling any component, circuit board mod
Page 4 · click to enlarge
Page 4

SERVICING PRECAUTIONS

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or expo sure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as “anti-static” can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electri cally shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replace ment ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity suf ficient to damage an ES device.)

General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before;

a. Removing or reinstalling any component, circuit board mod

ule or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection. c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explo sion hazard. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.

General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 °F to 600 °F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire- bristle (0.5 inch, or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature.

(500 °F to 600 °F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuit board printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature

Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged eas ily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component dam age caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alter natively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent poten tial shock reasons prior to applying power to the unit under test.

(500 °F to 600 °F) b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the compo nent lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

- 4 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 5 of the LG Electronics 463 user manual
Page 5 · click to enlarge
Page 5

IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the cir cuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.

3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures.

Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.

Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).

At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connec tions).

1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.

"Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.

At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.

Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink.

1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly con nected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.

Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as pos sible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.

Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top.

- 5 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 6 of the LG Electronics 463 user manual
Page 6 · click to enlarge
Page 6

SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement.

1. Application range This specification is applied to the LCD TV used LD21C chassis.
3. Test method 1) Performance: LGE TV test method followed 2) Demanded other specification - Safety : CE, IEC specification - EMC : CE, IEC
2. Requirement for Test Each part is tested as below without special appointment.

1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C 2) Relative Humidity: 65 % ± 10 % 3) Power Voltage : Standard input voltage (AC 100-240 V~, 50/60 Hz) * Standard Voltage of each products is marked by models. 4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM. 5) The receiver must be operated for about 5 minutes prior to the adjustment.

4. Model General Specification No.ItemSpecificationRemarks 1MarketEU(PAL Market-37Countries)DTV & Analog (Total 37 countries) DTV (MPEG2/4, DVB-T) :37 countries UK/Italy/Germany/France/Spain/Sweden/Finland/Nether lands/ Belgium/Luxemburg/ Greece/Denmark/Czech/ Austria /Hungary/Swiss/Croatia/Turkey Norway/Slovenia/Poland/Ukraine/Portugal/Ireland/Morocco/ Latvia/Estonia/Lithania/Rumania/Bulgaria/Russia/Slovakia Bosnia/Serbia/Albania/Kazakhstan/Belarus DTV (MPEG2/4, DVB-T2): 8 countries UK/Denmark/Sweden/Finland/Norway/Ireland/Ukraine/ Kazakhstan DTV (MPEG2/4, DVB-C): 37 countries UK/Italy/Germany/France/Spain/Sweden/Finland/Nether lands/ Belgium/Luxemburg/ Greece/Denmark/Czech/ Austria /Hungary/Swiss/Croatia/Turkey Norway/Slovenia/Poland/Ukraine/Portugal/Ireland/Morocco/ Latvia/Estonia/Lithania/Rumania/Bulgaria/Russia/Slovakia Bosnia/Serbia/Albania/Kazakhstan/Belarus DTV (MPEG2/4,DVB-S): 29 countries Italy/Germany/France/Spain/Netherlands/ Belgium/ Luxemburg/ Greece/ Czech/Austria /Hungary/Swiss/ Croatia/ Turkey/Slovenia/Poland/Portugal/ Morocco/Latvia/ Estonia/Lithania/Rumania/Bulgaria/Russia/Slovakia Bosnia/Serbia/Albania/ Belarus Supported satellite : 22 satellites HISPASAT 1C/1D, ATLANTIC BIRD 2, NILESAT 101/102, ATLANTIC BIRD 3, AMOS 2/3, THOR 5/6, IRIUS 4, EUTELSAT-W3A, EUROBIRD 9A, EUTELSAT-W2A, HOTBIRD 6/8/9, EUTELSAT-SESAT, ASTRA 1L/H/M/ KR, ASTRA 3A/3B, BADR 4/6, ASTRA 2D, EUROBIRD 3, EUTELSAT-W7, HELLASSAT 2, EXPRESS AM1, TURK SAT 2A/3A, INTERSAT10

- 6 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 7 of the LG Electronics 463 user manual
Page 7 · click to enlarge
Page 7
No.ItemSpecificationRemarks 2Broadcasting system1) PAL-BG 2) PAL-DK 3) PAL-I/I’ 4) SECAM L/L’ 5) DVB-T/T2/C/S 3Receiving systemAnalog : Upper Heterodyne Digital : COFDM, QAM► DVB-T - Guard Interval(Bitrate Mbit/s) _ 1/4, 1/8, 1/16, 1/32 - Modulation : Code Rate QPSK : 1/2, 2/3, 3/4, 5/6, 7/8 16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8 ► DVB-T2 - Guard Interval(Bitrate Mbit/s) _ 1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256, - Modulation : Code Rate QPSK : 1/2, 2/5, 2/3, 3/4, 5/6 16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6 ► DVB-C - Symbolrate : 4.0Msymbols/s to 7.2Msymbols/s - Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM ► DVB-S/S2 - symbolrate DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s DVB-S (QPSK) : 2 ~ 45Msymbol/s - viterbi DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8 DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10 4Scart Jack (1EA)PAL, SECAMScart 1 Jack is Full scart and support RF-OUT(analog). 5Video Input RCA(1EA)PAL, SECAM, NTSC4 System : PAL, SECAM, NTSC, PAL60 6Component Input (1EA)Y/Cb/Cr Y/Pb/Pr 7RGB InputRGB-PCAnalog(D-SUB 15PIN) Some models (LD21A,LD21C) are not supported. 8HDMI Input (3EA)HDMI1-DTV/DVI HDMI2-DTV HDMI3-DTVPC(HDMI version 1.3) Support HDCP The number of Input ports is different by model. 9Audio Input (2EA)RGB/DVI Audio Component & AVIn case of the RGB/DVI Audio input, Some models(LD21A,LD21C) are not supported. Component & AV’s audio input is used by common port. 10SDPIF out (1EA)SPDIF outSome models(LD21A,LD21C) are not supported. 11Earphone out (1EA)Antenna, AV1, AV2, Component, RGB, HDMI1, HDMI2, HDMI3Some models(LD21A,LD21C) are not supported. 12USB (1EA or 2EA)EMF, DivX HD, For SVC (download)JPEG, MP3, DivX HD LM58, CM96: 2EA LS56, LS35, CS46, LS,34, LM34 : 1EA 13DVBDVB-TCI : U K, Finland, Denmark, Norway, Sweden, Russia, Spain, Ireland, Luxemburg, Belgium, Netherland CI+ : France(Canal+), Italy(DGTVi) DVB-CCI : Switzerland, Austria, Slovenia, Hungary, Bulgaria CI+ : S witzerland(UPC,Cablecom), Netherland(Ziggo), Germany(KDG,CWB), Finland(labwise) DVB-SCI + : Germany(Astra HD+ ) 14Ethernet (1EA)DLNA(Wired, DMP only)Some models (LD21A,LD21C) are not supported.

- 7 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 8 of the LG Electronics 463 user manual
Page 8 · click to enlarge
Page 8
5. Video resolutions (2D) 5.1. Component Input (Y, CB/PB, CR/PR) No.ResolutionH-freq(kHz)V-freq(Hz)Pixel clock(MHz)Proposed 1720*57615.62550.0013.5SDTV ,DVD 576I 2720*48015.7360.0013.5135SDTV ,DVD 480I 3720*48015.7359.9413.50SDTV ,DVD 480I 4720*57631.2550.0027.00SDTV 576P 5720*48031.5060.0027.027SDTV 480P 6720*48031.4759.9427.00SDTV 480P 71280*72037.5050.0074.25HDTV 720P 81280*72045.0060.0074.25HDTV 720P 91280*72044.9659.9474.176HDTV 720P 101920*108028.12550.0074.25HDTV 1080I 111920*108033.7560.0074.25HDTV 1080I 121920*108033.7259.9474.176HDTV 1080I 131920*108056.2550.00148.50HDTV 1080P 141920*108067.5060.00148.50HDTV 1080P 151920*108067.43259.94148.352HDTV 1080P 161920*108027.0024.0074.25HDTV 1080P 171920*108026.9723.9474.176HDTV 1080P 181920*108033.7530.0074.25HDTV 1080P 191920*108033.7129.9774.176HDTV 1080P
LG Electronics 463 diagram (page 8)
Fig. 6

5.2. RGB Input (PC) – LS35/LS34/CS46 series models are not supported.

No.ResolutionH-freq(kHz)V-freq.(Hz)Pixel clock(MHz)ProposedDDC 1640*35031.46870.0925.17EGAX 2720*40031.46970.0828.32DOSO 3640*48031.46959.9425.17VESA(VGA)O 4800*60037.87960.3140.00VESA(SVGA)O 51024*76848.36360.0065.00VESA(XGA)O 61152*86454.34860.05380.00VESAO 71360*76847.71260.01585.50VESA (WXGA)O 81920*108067.560148.5HDTV 1080PO
LG Electronics 463 diagram (page 8)
Fig. 7

- 8 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 9 of the LG Electronics 463 user manual
Page 9 · click to enlarge
Page 9
LG Electronics 463 diagram (page 9)
Fig. 8
No.ResolutionH-freq(kHz)V-freq.(Hz)Pixel clock(MHz)ProposedRemark PC(DVI)DDC 1640*35031.46870.0925.17EGAX 2720*40031.46970.0828.32DOSO 3640*48031.46959.9425.17VESA(VGA)O 4800*60037.87960.3140.00VESA(SVGA)O 51024*76848.36360.0065.00VESA(XGA)O 61152*86454.34860.05380.00VESAO 71360*76847.71260.01585.50VESA (WXGA)O 81280*102463.98160.020108.0VESA (SXGA)OFHD only 91920*108067.5060.00148.5HDTV 1080POFHD only DTV 1720*48031.4759.9427.00SDTV 480P 2720*48031.5060.0027.027SDTV 480P 3720*57631.25050.0027.00SDTV 576P 41280*72037.5050.0074.25HDTV 720P 51280*72045.0060.0074.25HDTV 720P 61280*72044.9659.9474.176HDTV 720P 71920*108028.12550.0074.25HDTV 1080I 81920*108033.7560.0074.25HDTV 1080I 91920*108033.7259.9474.176HDTV 1080I 101920*108056.25050.00148.50HDTV 1080P 111920*108067.5060.00148.50HDTV 1080P 121920*108067.43259.94148.352HDTV 1080P 131920*108027.0024.0074.25HDTV 1080P 141920*108026.9723.97674.176HDTV 1080P 151920*108033.7530.0074.25HDTV 1080P

- 9 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 10 of the LG Electronics 463 user manual — filexxx.bin
Page 10 · click to enlarge
Page 10

ADJUSTMENT INSTRUCTION

1. Application Range This specification sheet is applied to all of the LCD TV with LD21C chassis.

(4) Click "Connect" tab. If "Can't" is displayed, check connection

between computer, jig, and set.

LG Electronics 463 — (4) Click "Connect" tab. If "Can't" is displayed, check connection diagram (page 10)
Fig. 9 · (4) Click "Connect" tab. If "Can't" is displayed, c…

(2)

(3)

2. Designation (1) The adjustment is according to the order which is designated

and which must be followed, according to the plan which can be changed only on agreeing. (2) Power adjustment : Free Voltage. (3) Magnetic Field Condition: Nil. (4) Input signal Unit: Product Specification Standard. (5) Reserve after operation : Above 5 Minutes (Heat Run) Temperature : at 25 °C ± 5 °C Relative humidity : 65 ± 10 % Input voltage : 220 V, 60 Hz (6) Adjustment equipments: Color Analyzer(CA-210 or CA-110),

Please Check the SpeedTo use speed between from 200KHz to 400KHz

(5) Click "Auto" tab and set as below. (6) Click "Run". (7) After downloading, check "OK" message.

DDC Adjustment Jig, Service remote control. (7) Push the "IN STOP" key - For memory initialization.

LG Electronics 463 — (2) diagram (page 10)
Fig. 10

Case1 : Software version up

(4)

1. After downloading S/W by USB , TV set will reboot automatically. 2. Push “In-stop” key. 3. Push “Power on” key. 4. Function inspection 5. After function inspection, Push “In-stop” key. Case2 : Function check at the assembly line

filexxx.bin

(5)

(7)...........OK

1. When TV set is entering on the assembly line, Push “In-stop” key at first. 2. Push “Power on” key for turning it on. → If you push “Power on” key, TV set will recover

(6)

channel information by itself. 3. After function inspection, Push “In-stop” key.

* USB DOWNLOAD (1) Put the USB Stick to the USB socket. (2) Automatically detecting update file in USB Stick.

3. Main PCB check process ▪ APC - After Manual-Insert, executing APC

- If your downloaded program version in USB Stick is Low,

it didn't work. But your downloaded version is High, USB data is automatically detecting. (3) Show the message "Copying files from memory". (4) Updating is starting.

* Boot file Download (1) Execute ISP program "Mstar ISP Utility" and then click

"Config" tab. (2) Set as below, and then click "Auto Detect" and check "OK"

LG Electronics 463 — 3. Main PCB check process ▪ APC - After Manual-Insert, executing APC diagram (page 10)
Fig. 11 · 3. Main PCB check process ▪ APC - After Manual-Inser…
LG Electronics 463 — 3. Main PCB check process ▪ APC - After Manual-Insert, executing APC diagram (page 10)
Fig. 12 · 3. Main PCB check process ▪ APC - After Manual-Inser…

message. If "Error" is displayed, check connection between computer, jig, and set. (3) Click "Read" tab, and then load download file(XXXX.bin)

by clicking "Read"

(5) Updating Completed, The TV will restart automatically. (6) If your TV is turned on, check your updated version and

LG Electronics 463 — by clicking "Read" diagram (page 10)
Fig. 13 · by clicking "Read"

(1)

Tool option. (explain the Tool option, next stage) * If downloading version is more high than your TV have, TV can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didn’t have a DTV/ ATV test on production line.

filexxx.bin

* After downloading, have to adjust Tool Option again. (1) Push "IN-START" key in service remote control. (2) Select "Tool Option 1" and push "OK" key. (3) Punch in the number. (Each model has their number)

- 10 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 11 of the LG Electronics 463 user manual — 12. Sub B/C
Page 11 · click to enlarge
Page 11

3.1. ADC Process (1) ADC

3.3. EDID data (1) HD RGB EDID data(HD RGB input: only LM34 Model support)

- Enter Service Mode by pushing "ADJ" key, - Enter Internal ADC mode by pushing "►" key at "7. ADC

0123456789ABCDEF 0000FFFFFFFFFFFF001E6Dab 10c010368A05A780AEE91A3544C9926 20 30 400F 01 3550 01 0054 01 40A1 01 8408 01 0000 01 0071 1B 0040 21 1C61 50 0140 A0 1D45 51 0040 00 7231 1E 5140 30 D001 48 1E01 88 20 50 60 706E 28 55 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A 3E 1F 46 10 00 0A 20 d d 00 e

Calibration".

EZ ADJUST

ADC Calibration

0. Tool Option1

ADC Comp 480i NG

1. Tool Option2

ADC Comp 1080p NG

2. Tool Option3

ADC RGB NG

3. Tool Option4

4. Tool Option 5

Start Reset

5. Country Group

6. Area Option

(2) HD HDMI EDID data

7. ADC Calibration ඖ

0123456789ABCDEF 0000FFFFFFFFFFFF001E6Dab 10c010380A05A780AEE91A3544C9926 200F5054A1080031404540614071400101 30010101010101662150B051001B304070 40360040846300001E6419004041002630 5018880306408463000018000000FD003A 603E1E5310000A202020202020d 70d01e 80020322F14E101F841305140302122021 9022150126150750095707f A0801E011D8018711C1620582C2500A05A B00000009E011D007251D01E206E285500 C020C23100001E8C0AD08A20E02D10103E D09600A05A00000018023A801871382D40 E0582C4500A05A0000001E000000000000 F0000000000000000000000000000000e

8. White Balance

9. 10 Point WB

10. Test Pattern

11. EDID D/L

12. Sub B/C

13. Touch Sensitivity Setting

<Caution> Using "power on" key of the Adjustment remote

control, power on TV.

* ADC Calibration Protocol (RS232)

NOItem CMD 1CMD 2Data 0 Enter Adj Adjust MODE ‘Moust A de In’A0 0When transfer the ‘Mode In’, Carry the command. ADC adjust ADC Adjust AD1 0 (Automatically adjustment The use of a internal pattern)
  • Adjust Sequence
  • aa 00 00 [Enter Adjust Mode]
  • xb 00 40 [Component1 Input (480i)]
  • ad 00 10 [Adjust 480i Comp1]
  • xb 00 60 [RGB Input (1024*768)] (only LD21B)
  • ad 00 10 [Adjust 1024*768 RGB] (only LD21B)
  • aa 00 90 End Adjust mode * Required equipment : Adjustment remote control.

(3) Detail EDID Options are below

a. Product ID

MODEL NAMEHEXEDID TableDDC Function HD/FHD Model000101 00Analog/Digital
b. Serial NoControlled on production line. c. Month, Year: Controlled on production line:

ex) Week : '01' -> '01'

  • 3.2. EDID Download
  • After enter Service Mode by pushing "ADJ" key.
  • Enter EDID D/L menu.
  • Enter "START" by pushing "OK" key.

Year : '2012' -> '16' fix d. Model Name(Hex):

cf) TV set’s model name in EDID data is below.

Model nameMODEL NAME(HEX) LG TV00 00 00 FC 00 4C 47 20 54 56 0A 20 (LG TV)

EZ ADJUST

EDID D/L

0. Tool Option1

HDMI1

NG

e. Checksum: Changeable by total EDID data.

1. Tool Option2

HDMI2

NG

EDID C/S dataFHD(10 Bit) HDMIRGB Check sum (Hex)Block 0A4CD Block 15B (HDMI1)- 4B (HDMI2) 3B (HDMI3)

2. Tool Option3

HDMI3

NG

3. Tool Option4

RGB

NG

4. Tool Option 5

Start Reset

5. Country Group

6. Area Option

7 . ADC Calibration

8. White Balance

9. 10 Point WB

10. Test Pattern

f. Vendor Specific(HDMI)

11 . EDID D/L

ඖ

InputModel name(HEX) HDMI167030C001000 HDMI267030C002000 HDMI367030C003000

12. Sub B/C

13. Touch Sensitivity Setting

<Caution> Never connect HDMI && D-sub cable when EDID

downloaded.

- 11 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 12 of the LG Electronics 463 user manual — 172 172 192 64 64 64 ON 100 To Set
Page 12 · click to enlarge
Page 12

3.4 Function Check - Check display and sound

* Auto-control interface and directions (1) Adjust in the place where the influx of light like floodlight

  • Check Input and Signal items.

around is blocked. (illumination is less than 10 lux). (2) Adhere closely the Color analyzer(CA210) to the module

1. TV 2) AV (SCART / CVBS) 3) COMPONENT (480i) 4) RGB (PC : 1024 x 768 @ 60hz) (* RGB input : LD21B only support) 5) HDMI 6) PC Audio In (* except LD21A chassis model) * Display and Sound check is executed by Remote control.

less than 10 cm distance, keep it with the surface of the Module and Color analyzer's prove vertically.(80° ~ 100°). (3) Aging time

- After aging start, keep the power on (no suspension of

power supply) and heat-run over 5 minutes. - Using 'no signal' or 'POWER ONLY' or the others, check

the back light on.

Not to push the INSTOP key after completion if the function inspection.

  • Auto adjustment Map(using RS-232C to USB cable)

RS-232C COMMAND [CMD ID DATA] Wb 00 00 White Balance Start Wb 00 ff White Balance End

4. Total Assembly line process 4.1. Adjustment Preparation ▪ W/B Equipment condition

RS-232C COMMAND [CMD ID DATA]MINCENTER (DEFAULT)MAX CoolMidWarmCoolMidWarm R GainjgJajd00172192192192 G GainjhJbje00172192192192 B GainjiJcjf00192192172192 R Cut646464128 G Cut646464128 B Cut646464128

CA210 : CCFL/EEFL -> CH9, Test signal: Inner pattern(80IRE) LED -> CH14, Test signal: Inner pattern(80IRE) ▪ If it is executed W/B adjustment in 2~3 minutes H/run, it is

adjusted by Target data

ModeTempCoordinate specTarget Cool13,000kX=0.269 (±0.002) Y=0.273 (±0.002)X=0.271 Y=0.276LAMP <Test Signal> Inner pattern (204gray, 80IRE) Medium9,300kX=0.285 (±0.002) Y=0.293 (±0.002)X=0.287 Y=0.296 Warm6,500kX=0.313 (±0.002) Y=0.329 (±0.002)X=0.315 Y=0.332

<Caution>

Color Temperature : COOL, Medium, Warm. One of R Gain/G Gain/ B Gain should be kept on 0xC0, and adjust other two lower than C0.(When R/G/B Gain are all C0, it is the FULL Dynamic Range of Module)

* Connecting picture of the measuring instrument (On Automatic control) Inside PATTERN is used when W/B is controlled. Connect to auto controller or push Adjustment R/C POWER ON → Enter the mode of White-Balance, the pattern will come out.

  • * Manual W/B process using adjust Remote control.
  • After enter Service Mode by pushing "ADJ" key,
  • Enter White Balance by pushing "►" key at "8. White

Balance".

EZ ADJUST

White Balance

Color Temp. R-Gain G-Gain B-Gain R-Cut G-Cut B-Cut Test-Pattern Backlight Reset

Cool

0. Tool Option1 1. Tool Option2 2. Tool Option3 3. Tool Option4 4. Tool Option5 5. Country Group 6. Area Option 7. ADC Calibration 8. White Balance ► 9. 10 Point WB 10. Test Pattern 11. EDID D/L 12. Sub B/C 13. Touch Sensitivity Setting

172 172 192 64 64 64 ON 100 To Set

Full White Pattern CA-210

COLOR ANALYZER TYPE : CA-210

RS-232C Communication

* After you finished all adjustments, Press "In-start" key and compare Tool option and Area option value with its BOM, if it is correctly same then unplug the AC cable. If it is not same, then correct it same with BOM and unplug AC cable. For correct it to the model's module from factory Jig model. * Push the "IN STOP" key after completing the function inspection. And Mechanical Power Switch must be set “ON”.

- 12 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 13 of the LG Electronics 463 user manual — 872 , pattern No.83)
Page 13 · click to enlarge
Page 13

4.2. EYE-Q function check (1) Turn on TV. (2) Press EYE key of Adjustment remote control. (3) Cover the Eye Q II sensor on the front of the using your

4.4. IR emitter inspection (1) Start 3D pattern inspection. (2) If IR emitter signal is correctly received to IR receiver, the

lamp of IR tester turn on.

hand and wait for 6 seconds. (4) Confirm that R/G/B value is lower than 10 of the "Raw

LG Electronics 463 diagram (page 13)
Fig. 14

Data (Sensor data, Back light)". If after 6 seconds, R/G/B value is not lower than 10, replace Eye Q II sensor. (5) Remove your hand from the Eye Q II sensor and wait for 6

seconds. (6) Confirm that "ok" pop up. If change is not seen, replace

Eye Q II sensor.

4.3. 3D function test (Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4]) * HDMI mode NO. 872 , pattern No.83 (1) Please input 3D test pattern like below. (HDMI mode No.

4.5. Outgoing condition Configuration ■ When pressing IN-STOP key by SVC remocon, Red LED

872 , pattern No.83)

are blinked alternatively. And then automatically turn off. (Must not AC power OFF during blinking)

LG Electronics 463 — 872 , pattern No.83) diagram (page 13)
Fig. 15 · 872 , pattern No.83)

(2) When 3D OSD appear automatically , then select OK key.

LG Electronics 463 — 872 , pattern No.83) diagram (page 13)
Fig. 16 · 872 , pattern No.83)

(3) Don't wear a 3D Glasses, Check the picture like below.

LG Electronics 463 — 872 , pattern No.83) diagram (page 13)
Fig. 17 · 872 , pattern No.83)

- 13 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 14 of the LG Electronics 463 user manual — 6.1. Signal Table
Page 14 · click to enlarge
Page 14
5. HI-POT Test 5.1. HI-POT auto-check preparation - Check the POWER cable and SIGNAL cable insertion condition

6.2. Comand Set

Adjust mode CMD(hex) LENGTH(hex) Description

EEPROM WRITE A0h 84h+n n-bytes Write (n = 1~16)

* Description FOS Default write : write Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0, Phase Data write : Model Name and Serial Number write in EEPROM,.

5.2. HI-POT auto-check (1) Pallet moves in the station. (POWER CORD / AV CORD is

tightly inserted) (2) Connect the AV JACK Tester. (3) Controller (GWS103-4) on. (4) HI-POT test (Auto)

6.3. Method & notice (1) Serial number D/L is using of scan equipment. (2) Setting of scan equipment operated by Manufacturing

- If Test is failed, Buzzer operates. - If Test is passed, GOOD Lamp on and move to next proc ess automatically.

Technology Group. (3) Serial number D/L must be conformed when it is produced in

5.3. Checkpoint (1) Test voltage

production line, because serial number D/L is mandatory by D-book 4.0.

- Touchable Metal : 3KV / min at 100mA - SIGNAL : 3KV / min at 100mA (2) TEST time: 1 second. (case : mass production ) (3) TEST POINT

* Manual Download(Model Name and Serial Number) If the TV set is downloaded by OTA or Service man, sometimes model name or serial number is initialized.(Not always) There is impossible to download by bar code scan, so It need Manual download. 1) Press the "Instart" key of Adjustment remote control. 2) Go to the menu "6.Model Number D/L" like below photo. 3) Input the Factory model name or Serial number like photo.

- Touchable Metal => LIVE & NEUTRAL : Touchable Metal. - SIGNAL => LIVE & NEUTRAL : SIGNAL.

6. Model name & Serial number D/L ▪ Press "Power on" key of service remote control.
LG Electronics 463 — 5.3. Checkpoint (1) Test voltage diagram (page 14)
Fig. 18 · 5.3. Checkpoint (1) Test voltage
  • (Baud rate : 115200 bps)
  • Connect RS232 Signal Cable to RS-232 Jack.
  • Write Serial number by use RS-232.
  • Must check the serial number at the Product/Service info..

(menu key -> red key -> select product/Service info)

LG Electronics 463 — (menu key -> red key -> select product/Service info) diagram (page 14)
Fig. 19 · (menu key -> red key -> select product/Service info)
LG Electronics 463 — (menu key -> red key -> select product/Service info) diagram (page 14)
Fig. 20 · (menu key -> red key -> select product/Service info)
LG Electronics 463 — (menu key -> red key -> select product/Service info) diagram (page 14)
Fig. 21 · (menu key -> red key -> select product/Service info)
4. Check the model name Instart menu. → Factory name displayed. (ex 32LV3400-ZG) 5) Check the Diagnostics.(DTV country only) → Buyer model displayed.(ex 32LV3400-ZG)
LG Electronics 463 — (menu key -> red key -> select product/Service info) diagram (page 14)
Fig. 22 · (menu key -> red key -> select product/Service info)

6.1. Signal Table

CMD LENGTH ADH ADL DATA_1 . . . Data_n CS DELAY

CMD : A0h LENGTH : 85~94h (1~16 bytes) ADH : EEPROM Sub Address high (00~1F) ADL : EEPROM Sub Address low (00~FF) Data : Write data CS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_n Delay : 20ms

- 14 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 15 of the LG Electronics 463 user manual — *IP Number : 12.12.2.2
Page 15 · click to enlarge
Page 15
  • 7. MAC Address & CI+ key download 7.1 MAC Address 7.1.1 Equipment & Condition
  • Play file : Serial.exe
  • MAC Address edit
  • Input Start / End MAC address

7.2 LAN Inspection 7.2.1. Equipment & Condition ▪ Each other connection to LAN Port of IP Hub and Jig

LG Electronics 463 diagram (page 15)
Fig. 23

7.1.2 Download method (1) Communication Prot connection

LG Electronics 463 — 7.1.2 Download method (1) Communication Prot connection diagram (page 15)
Fig. 24 · 7.1.2 Download method (1) Communication Prot connect…
  • 7.2.2. LAN inspection solution
  • LAN Port connection with PCB
  • Network setting at MENU Mode of TV
  • Setting automatic IP
  • Setting state confirmation

Connection : PCBA (USB Port) → USB to Serial Adapter (UC-232A) → RS-232C cable → PC(RS-232C port) * Caution : LJ21* chassis support only UC-232A driver. (only use this one. )

-> If automatic setting is finished, you confirm IP and MAC

Address.

LG Electronics 463 — -> If automatic setting is finished, you confirm IP and MAC diagram (page 15)
Fig. 25 · -> If automatic setting is finished, you confirm IP…

(2) MAC Address & CI+ Key Download

  • Set CI+ Key path Directory at Start Mac & CI+ Download

Programme ▪ Com 1,2,3,4 and 115200(Baudrate)

LG Electronics 463 — Programme ▪ Com 1,2,3,4 and 115200(Baudrate) diagram (page 15)
Fig. 26 · Programme ▪ Com 1,2,3,4 and 115200(Baudrate)

7.3. LAN PORT INSPECTION(PING TEST) Connect SET -> LAN port == PC -> LAN Port

GP4_LOW

SET PC

7.3.1. Equipment setting (1) Play the LAN Port Test PROGRAM. (2) Input IP set up for an inspection to Test Program.

*IP Number : 12.12.2.2

  • Port connection button click(1)
  • Push the (2) MAC Address write.
  • At success Download, check the OK (3).
  • Start CI+ Key Download, Push the (4).
  • Check the OK or NG.

7.3.2. LAN PORT inspection (PING TEST) (1) Play the LAN Port Test Program. (2) Connect each other LAN Port Jack. (3) Play Test (F9) button and confirm OK Message. (4) Remove LAN cable.

LG Electronics 463 — *IP Number : 12.12.2.2 diagram (page 15)
Fig. 27 · *IP Number : 12.12.2.2
LG Electronics 463 — *IP Number : 12.12.2.2 diagram (page 15)
Fig. 28 · *IP Number : 12.12.2.2

- 15 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 16 of the LG Electronics 463 user manual
Page 16 · click to enlarge
Page 16
LG Electronics 463 diagram (page 16)
Fig. 29

- 16 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 17 of the LG Electronics 463 user manual
Page 17 · click to enlarge
Page 17
LG Electronics 463 diagram (page 17)
Fig. 30

- 17 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 18 of the LG Electronics 463 user manual
Page 18 · click to enlarge
Page 18
LG Electronics 463 diagram (page 18)
Fig. 31

- 18 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 19 of the LG Electronics 463 user manual — * Set + Stand * Stand Base + Body
Page 19 · click to enlarge
Page 19
LG Electronics 463 — #EV# diagram (page 19)
Fig. 32

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

* Set + Stand * Stand Base + Body

- 19 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Page 20 of the LG Electronics 463 user manual — PWM1
Page 20 · click to enlarge
Page 20
LG Electronics 463 — #EV# diagram (page 20)
Fig. 33

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. POWER_LARGE

0.33uF 16V +12V/+15V

NON_PSU_T120_LGD

FROM LIPS & POWER B/D

CIS21J121

R611

OPT

0.1uF 16V R412

FM20020-24

3.6uH IC401

0.01uF 50V

NORMAL_32

18 INV ON

21 12V 22 P.DIM1

23 GND/P.DIM2 24 Err OUT

OPT

R475

10 3.5V

12 3.5V

20 A.DIM

P404

6 GND

8 GND

14 GND

R608

12K

+5V_USB

[EP]LX

5 COMP

FW20020-24S

P401 SMAW200-H24S2

8 NC

7 SS

6 EN

NORMAL_EXPEPT_32

1 PWR ON

5 GND

7 GND

11 3.5V

13 GND

15 GND

SLIM_32~52

LED models need not use.

AOZ1051PI

P403

’ERROR_OUT’ is used for

lamp(CCFL/EEFL) models.

R410

10K L401

THERMAL

1 PGND

2 VIN

3 AGND

4 FB

Vout=0.8*(1+R1/R2)

MMBT3906(NXP)

OPT

R610 33K

R2

Q402

OPT

R476

In other words,

MLB-201209-0120P-N2

OPT

0.1uF 16V

R423

0.1uF 16V

FOR 200HZ PWM_DIM2

R408

12K 1%

R406

4.7K

L404-*1

OPT

R609

MMBT3904(NXP)

0.1uF 16V

11K

OPT

R1

CIS21J121

R416

56K

OPT

Q401

MLB-201209-0120P-N2

E

CIS21J121

L402-*1

0.1uF 16V

PWM1

+3.5V_ST

B

R401

+3.5V_ST

10K OPT

10K

R462

10K

+12V/+15V

R461

RL_ON

Show 8 more labels / short text on this page
22uF 16V · 16 GND/V-sync · 2200pF 50V · 1% · 1% · 100pF · 10uF 25V · 10uF 25V OPT
Page 21 of the LG Electronics 463 user manual — OPT
Page 21 · click to enlarge
Page 21
LG Electronics 463 — #EV# diagram (page 21)
Fig. 34

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LVDS_LARGE

LVDS for large inch

OPT

AUO_GND

AUO_GND/LGD_NC

R709

10K

OPT

PSU_T120_LGD PWM_DIM

PANEL_VCC

FHD

[51Pin LVDS Connector]

R706

RXA4+

RXA4-

RXA3+

RXA3-

RXACK-

RXA2+

RXA2-

RXA1+

RXA1-

RXA0+

RXB4+

RXB4-

RXB3+

RXB3-

RXBCK+

RXBCK-

RXB2+

RXB2-

RXB1+

RXB1-

RXB0+

RXB0-

(For FHD 60Hz)

FI-RE51S-HF-J-R1500

FHD

P703

1000pF 50V · 10uF 16V · 70-ohm

Page 22 of the LG Electronics 463 user manual — AVDD_DDR0
Page 22 · click to enlarge
Page 22
LG Electronics 463 — #EV# diagram (page 22)
Fig. 35

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. DDR_256

CLose to Saturn7M IC CLose to DDR3 CLose to DDR3 CLose to Saturn7M IC

0.1uF OS

AVDD_DDR0

0.01uF 50V

R1231

10K

R1235 56

R1236 56

A-MRASB

A-MCASB

A-MRESETB

A-MDQSL

A-MDQSLB

A-MDQSU

A-MDQSUB

A-MDQL1

A-MDQL2

A-MDQL3

A-MDQL4

A-MDQL5

A-MDQL6

A-MDQL7

A-MDQU0

A-MDQU1

A-MDQU2

A-MDQU3

A-MDQU4

A-MDQU5

A-MDQU6

A-MDQU7

A-MA0

A-MA1

A-MA2

A-MA3

A-MA4

A-MA5

A-MA6

A-MA7

A-MA8

A-MA9

A-MA10

A-MA11

A-MA12

A-MA13

A-MCKE

A-MODT

A-MWEB

A-MDML

A-MDMU

B-MVREFCA

A-MBA0

A-MBA1

A-MBA2

A-MVREFCA

A0 N3

A1 P7

A2 P3

A3 N2

A4 P8

A5 P2

A6 R8

A7 R2

A8 T8

A9 R3

A10/AP L7

A11 R7

A12/BC N7

A13 T3

NC_5 M7

BA0 M2

BA1 N8

BA2 M3

CK J7

CK K7

CKE K9

CS L2

ODT K1

RAS J3

CAS K3

WE L3

RESET T2

DQSL F3

DQSL G3

DQSU C7

DQSU B7

DML E7

DMU D3

DQL0 E3

DQL1 F7

DQL2 F2

DQL3 F8

DQL4 H3

DQL5 H8

DQL6 G2

DQL7 H7

DQU0 D7

DQU1 C3

DQU2 C8

DQU3 C2

DQU4 A7

DQU5 A2

DQU6 B8

DQU7 A3

H5TQ1G63DFR-H9C IC1201

EAN61828901

DDR_1333_HYNIX

0.1uF

AVDD_DDR0

1K 1%

1K 1%

VREFCA M8

VREFDQ H1

VDD_1 B2

VDD_2 D9

VDD_3 G7

VDD_4 K2

VDD_5 K8

VDD_6 N1

VDD_7 N9

VDD_8 R1

VDD_9 R9

VDDQ_1 A1

VDDQ_2 A8

VDDQ_3 C1

VDDQ_4 C9

VDDQ_5 D2

VDDQ_6 E9

VDDQ_7 F1

VDDQ_8 H2

VDDQ_9 H9

VSS_1 A9

VSS_2 B3

VSS_3 E1

VSS_4 G8

VSS_5 J2

VSS_6 J8

VSS_7 M1

VSS_8 M9

VSS_9 P1

VSS_10 P9

VSS_11 T1

VSS_12 T9

VSSQ_1 B1

VSSQ_2 B9

VSSQ_3 D1

VSSQ_4 D8

VSSQ_5 E2

VSSQ_6 E8

VSSQ_7 F9

VSSQ_8 G1

VSSQ_9 G9

R1204

R1205

NC_1 J1

NC_2 J9

NC_3 L1

NC_4 L9

NC_6 T7

ZQ L8

A-MVREFDQ

R1203

C1207 0.1uF

C1208 0.1uF

C1210 0.1uF

C1211 0.1uF

C1212 0.1uF

C1213 0.1uF

C1214 0.1uF

C1215 0.1uF

C1216 0.1uF OS

A-MVREFCA

A-MVREFDQ

A-MA14

AVDD_DDR0

0.1uF

AVDD_DDR0

1K 1%

1K 1%

R1201

R1202

Show 7 more labels / short text on this page
1000pF OS · 1% · 1% · 1000pF · 240 1% · C1205 10uF · 1000pF
Page 23 of the LG Electronics 463 user manual — +3.5V_ST +3.5V_ST
Page 23 · click to enlarge
Page 23
LG Electronics 463 — #EV# diagram (page 23)
Fig. 36

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. SFLASH_1MB

SPI_SCK

SPI_SDI

OS

0.1uF

+3.5V_ST +3.5V_ST

R1405

OS

7 HOLD[IO3]

S_FLASH_MAIN_MACRONIX

5 SI/SIO0

S_FLASH_MAIN_WINBOND

5 DI[IO0]

MX25L8006EM2I-12G

7 HOLD#

6 SCLK

6 CLK

W25Q80BVSSIG

IC1401-*1

Serial Flash for SPI boot

1 CS#

2 SO/SIO1

3 WP#

4 GND

1 CS

2 DO[IO1]

3 %WP[IO2]

4 GND

R1404 4.7K

OPT

MMBT3904(NXP)

/SPI_CS

SPI_SDO

Q1401

+3.5V_ST

OPT

E

OPT

R1403

10K

B

OPT

R1401

/FLASH_WP

Page 24 of the LG Electronics 463 user manual — AR1901
Page 24 · click to enlarge
Page 24
LG Electronics 463 — #EV# diagram (page 24)
Fig. 37

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. PCMCI

R1908

R1905 10K

0.1uF

R1906 10K

R1907

0.1uF 16V

GND

R1904

+3.3V_CI

10K

10K

0.1uF 16V

0.1uF

AR1901

R1902 47

R1901 47

R1925 100

R1926 33

R1927 33

AR1903 33

BLM18PG121SN1D

CLOSE TO MSTAR

/CI_CD2

+3.3V_Normal

/CI_CD1

CI_TS_DATA[4]

CI_TS_DATA[5]

CI_TS_DATA[6]

CI_TS_DATA[7]

CI_MDI[0]

CI_MDI[1]

CI_MDI[2]

CI_MDI[3]

CI_MDI[4]

CI_MDI[5]

CI_MDI[6]

CI_MDI[7]

PCM_RST

/PCM_WAIT

REG

CI_TS_CLK

CI_TS_VAL

CI_TS_SYNC

CI_TS_DATA[0]

CI_TS_DATA[1]

CI_TS_DATA[2]

CI_TS_DATA[3]

CI_MISTRT

CI SLOT

CI_IORD

CI_IOWR

CI_MIVAL_ERR

CI_MCLKI

0.1uF

OPT

Show 4 more labels / short text on this page
10uF 10V · +5V_Normal · +5V_Normal · 2pF 50V
Page 25 of the LG Electronics 463 user manual — BS-R430051
Page 25 · click to enlarge
Page 25
LG Electronics 463 — #EV# diagram (page 25)
Fig. 38

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. ETHERNET

* H/W option : ETHERNET

ETHERNET

BS-R430051

JK2100-*1

ETHERNET_UDE

Page 26 of the LG Electronics 463 user manual — KEY1
Page 26 · click to enlarge
Page 26
LG Electronics 463 — #EV# diagram (page 26)
Fig. 39
LG Electronics 463 — #EV# diagram (page 26)
Fig. 40

IR/LED and control for on.y ’12 sub without IR-OUT.

+3.5V_ST

KEY1

KEY2

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Page 27 of the LG Electronics 463 user manual — 1 RF_S/W_CTL
Page 27 · click to enlarge
Page 27
LG Electronics 463 — #EV# diagram (page 27)
Fig. 41

so this has to be deleted in both main and ISDB sheet.

This was being applied to the only china demod,

GP4R_GLOBAL_TUNER_BLOCK

TU_T/C/S2

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

TDSN-G301D

13 +B4[1.23V]

5 +B1[3.3V]

7 +B2[1.8V]

12 +B3[3.3V]

TU2603

2 RESET

16 ERROR

18 VALID

1 NC_1

8 CVBS

9 NC_2

10 NC_3

11 NC_4

14 NC_5

17 SYNC

19 MCLK

3 SCL

4 SDA

6 SIF

15 GND

20 D0

21 D1

22 D2

23 D3

24 D4

25 D5

26 D6

27 D7

SHIELD

TU_T2/C

TDSS-G101D

9 IF_AGC

10 DIF[P]

11 DIF[N]

TU2602

2 RESET

5 +3.3V

7 +1.8V

TDSN-C201D

3 SCL

4 SDA

6 SIF

8 CVBS

TU2603-*1

1 RF_S/W_CTL

5 +B1[3.3V]

7 +B2[1.8V]

12 +B3[3.3V]

13 +B4[1.23V]

1 NC

TU_T/C

2 RESET

8 CVBS

9 NC_1

10 NC_2

11 NC_3

14 NC_4

16 ERROR

17 SYNC

18 VALID

19 MCLK

SHIELD

3 SCL

4 SDA

6 SIF

15 GND

20 D0

21 D1

22 D2

23 D3

24 D4

25 D5

26 D7

27 D8

TU_CHINA

SHIELD

Page 28 of the LG Electronics 463 user manual — LNB_TX
Page 28 · click to enlarge
Page 28
LG Electronics 463 — #EV# diagram (page 28)
Fig. 42

Input trace widths should be sized to conduct at least 3A

Ouput trace widths should be sized to conduct at least 2A

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

LNB_TX

LNB

1uF 50V

LNB

0.01uF 50V

ZD1

LNB

(Option:LNB)

MBR230LSFT1G

LNB

D2703

C2700 0.22uF 25V

LNB

A_GND

LNB_OUT

Page 29 of the LG Electronics 463 user manual — AMP_MUTE
Page 29 · click to enlarge
Page 29
LG Electronics 463 — #EV# diagram (page 29)
Fig. 43

AUDIO AMP(STA380BWE)

NON_LIPS

NON_LIPS

POWER_DET

10K

R3400

10K

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

AMP_MUTE

Page 30 of the LG Electronics 463 user manual — CAT24WC08W-T
Page 30 · click to enlarge
Page 30
LG Electronics 463 — #EV# diagram (page 30)
Fig. 44
B51_no_EJ4’b0000 Boot from 8051 with SPI flash
MIPS_SPE_NO_EJ4’b0100 Boot from MIPS with SPI flash
MIPS_SPI_EJ_14’b0101 Boot from MIPS with SPI flash
MIPS_SPI_EJ_24’b0110 Boot from MIPS with SPI flash

10 NC_7

11 NC_8

12 VCC_1

13 VSS_1

14 NC_9

15 NC_10

16 CLE

17 ALE

18 WE

19 WP

20 NC_11

21 NC_12

22 NC_13

23 NC_14

+3.3V_Normal

1 NC_1

2 NC_2

3 NC_3

4 NC_4

5 NC_5

6 NC_6

7 RY/BY

8 RE

9 CE

R144 2.2K

HDCP EEPROM EEPROM

4 GND

48 NC_29

47 NC_28

46 NC_27

45 NC_26

44 I/O7

43 I/O6

42 I/O5

41 I/O4

40 NC_25

39 NC_24

38 NC_23

37 VDD_2

36 VSS_2

35 NC_22

34 NC_21

33 NC_20

32 I/O3

31 I/O2

30 I/O1

29 I/O0

28 NC_19

27 NC_18

26 NC_17

25 NC_16 24 NC_15

R160 1K R161 1K

NAND_FLASH_1G_NUMONYX

48 NC_29

47 NC_28

46 NC_27

45 NC_26

40 NC_25

39 NC_24

38 NC_23

37 VCC_2

36 VSS_2

35 NC_22

34 NC_21

33 NC_20

28 NC_19

27 NC_18

26 NC_17

25 NC_16 24 NC_15

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

NAND01GW3B2CN6E

44 I/O7

43 I/O6

42 I/O5

41 I/O4

32 I/O3

31 I/O2

30 I/O1

29 I/O0

EAN60762401

R141 1K

R140 1K

NAND_FLASH_1G_SS

K9F1G08U0D-SCB0

Addr:10101--

EAN61857001

I2C_SCL

I2C_SDA

IC102-*2

1 NC_1

2 NC_2

3 NC_3

4 NC_4

5 NC_5

6 NC_6

7 RB

8 R

9 E

10 NC_7

11 NC_8

12 VDD_1

13 VSS_1

14 NC_9

15 NC_10

17 AL

18 W

19 WP

20 NC_11

21 NC_12

22 NC_13

23 NC_14

+3.3V_Normal

1 NC_1

2 NC_2

3 NC_3

4 NC_4

5 NC_5

6 NC_6

7 R/B

8 RE

9 CE

10 NC_7

11 NC_8

12 VCC_1

13 VSS_1

14 NC_9

15 NC_10

16 CLE

17 ALE

18 WE

19 WP

20 NC_11

21 NC_12

22 NC_13

23 NC_14

OS

R109 3.9K

0.1uF

PWM0

PWM2

OS

0.1uF

R128 22

R129 22

+3.3V_Normal

OS

R107 1K

OPT

R108 1K

R106 1K

MMBT3904(NXP)

48 NC_29

47 NC_28

46 NC_27

45 NC_26

44 I/O7

43 I/O6

42 I/O5

41 I/O4

40 NC_25

39 NC_24

38 NC_23

37 VCC_2

36 VSS_2

35 NC_22

34 NC_21

33 NC_20

32 I/O3

31 I/O2

30 I/O1

29 I/O0

28 NC_19

27 NC_18

26 NC_17

25 NC_16 24 NC_15

OS

R156 10K A_DIM

R157 100

R127 4.7K

NAND FLASH MEMORY

OPT

R105

1K

/PF_CE1

PF_ALE

/PF_WE

+3.3V_Normal

Q101

NAND_FLASH_1G_HYNIX

*Option : HDCP_EEPROM

OPT

H27U1G8F2BTR-BC

EAN35669102

IC102-*1

6 SCL

5 SDA

/F_RB

/PF_OE

/PF_CE0

E

A_DIM

2.2uF

CAT24WC08W-T

7 WP

OPT

R104

10K

B

3.3K

R102

4 VSS

OS

10 NC_7

11 NC_8

12 VCC_1

13 VSS_1

14 NC_9

15 NC_10

16 CLE

17 ALE

18 WE

19 WP

20 NC_11

21 NC_12

22 NC_13

23 NC_14

1 NC_1

2 NC_2

3 NC_3

4 NC_4

5 NC_5

6 NC_6

7 R/B

8 RE

9 CE

DIMMING

A_DIM

PWM_DIM

R113 4.7K

/PF_WP

Page 31 of the LG Electronics 463 user manual — R293 1K
Page 31 · click to enlarge
Page 31
LG Electronics 463 — #EV# diagram (page 31)
Fig. 45

DDCDA_DA/GPIO24 T5

DDCDA_CK/GPIO23 T4

HOTPLUGA/GPIO19 V5

HOTPLUGB/GPIO20 R5

DDCDC_DA/GPIO28 AE8

DDCDC_CK/GPIO27 AD8

HOTPLUGC/GPIO21 AC8

DDCDD_DA/GPIO30 R6

DDCDD_CK/GPIO29 U6

HOTPLUGD/GPIO22 P5

CEC/GPIO5 R4

RXACKP J2

RXACKN J3

RXCCKP AE9

RXCCKN AC9

RXDCKP F2

RXDCKN F3

HSYNC0 P2

VSYNC0 R3

SOGIN0 M1

HSYNC1 V2

VSYNC1 V3

SOGIN1 T3

HSYNC2 AA2

SOGIN2 W1

CVBSOUT0 Y6

CVBSOUT1 AA1

MODEL_OPT_0

MODEL_OPT_1

R204 100 OPT MODEL_OPT_2

MODEL_OPT_3

MODEL_OPT_4

MODEL_OPT_5

MODEL_OPT_6

MODEL_OPT_7

RXA0P K3

RXA0N J1

RXA1P K2

RXA1N K1

RXA2P L2

RXA2N L3

RXC0P AC10

RXC0N AD9

RXC1P AC11

RXC1N AD10

RXC2P AE11

RXC2N AD11

RXD0P G3

RXD0N F1

RXD1P G2

RXD1N G1

RXD2P H2

RXD2N H3

RIN0P N2

RIN0M P3

GIN0P N3

GIN0M N1

BIN0P M3

BIN0M M2

RIN1P U3

RIN1M U2

GIN1P T1

GIN1M T2

BIN1P R2

BIN1M R1

RIN2P Y2

RIN2M AA3

GIN2P W2

GIN2M Y3

BIN2P V1

BIN2M W3

CVBS0 AA8

CVBS1 Y4

CVBS2 W4

CVBS3 AA5

CVBS4 Y5

CVBS5 AA4

VCOM AB4

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

C211 0.047uF

C212 0.047uF

C213 0.047uF

C214 0.047uF

C215 0.047uF

C216 0.047uF

C218 0.047uF

C219 0.047uF

C220 0.047uF

C221 0.047uF

C222 0.047uF

C223 0.047uF

C225 0.047uF

C226 0.047uF

C227 0.047uF

C233 0.047uF

+3.3V_Normal

HD

FHD

R226 1K

R227 1K

Close to MSTAR

PHM_ON

PHM_OFF

R253 33

R254 68

R255 33 SC1_G+/COMP1_Y+

R256 68

R257 33

R258 68

R211 1K

R212 1K

R237 33

R238 68

R239 33

R240 68

R241 33

R242 68

R244 33

R245 33

R246 33

R252 68

DVB_T2

NON_DVB_T2

R208 1K

R209 1K

EPHY_RP

EPHY_RN

EPHY_TP

EPHY_TN

+2.5V_Normal

R206 1K

3D

R207 1K

NON_3D

OLED

NON_OLED

R4027 1K

R4029 1K

DVB_S

NON_DVB_S

R4028 1K

R4030 1K

+3.3V_Normal

120HZ

NON_120HZ

R291 1K

R294 1K

PC_L_IN

PC_R_IN

HP_LOUT

HP_ROUT

R290 1K

OS(not use) / NonOS_Non_ErrorOut

R293 1K

SCART1_RGB/COMP1

COMP2(common AV)

R203 100 RF_SW_OPT

*Opt : EU_OPT

R202 100 BOOSTER_OPT

CK+_HDMI1

CK-_HDMI1

D0+_HDMI1

D0-_HDMI1

D1+_HDMI1

D1-_HDMI1

D2+_HDMI1

D2-_HDMI1

DDC_SDA_1

DDC_SCL_1

PM_MODEL_OPT_1

CK+_HDMI2

CK-_HDMI2

D0+_HDMI2

D0-_HDMI2

D1+_HDMI2

D1-_HDMI2

D2+_HDMI2

D2-_HDMI2

DDC_SDA_2

DDC_SCL_2

CEC_REMOTE_S7

DSUB_HSYNC

DSUB_VSYNC

DSUB_R+

DSUB_R-

DSUB_G+

DSUB_G-

DSUB_B+

DSUB_B-

DSUB_SOG

SC1_ID

SC1_FB

SC1_SOG_IN

TU_CVBS

SC1_CVBS_IN

COMP2_Y+/AV_CVBS_IN

DTV/MNT_VOUT

R201 100 OPT

R4031 100 OPT

R4032 100 OPT

R4040 100 OPT

R4039 100 OPT

COMP2_Y+/AV_CVBS_IN

CVBS In/OUT

HPD1

HPD2

DSUB_B+

DSUB_B-

DSUB_SOG

SPDIF_OUT

DSUB

MODEL OPTION

HDMI

IF_AGC_SEL

LNA2_CTL

RF_SWITCH_CTL

DSUB_HSYNC

DSUB_VSYNC

DSUB_R+

DSUB_R-

DSUB_G+

DSUB_G-

Show 8 more labels / short text on this page
C217 1000pF · C224 1000pF · 1000pF OPT · OS(use) / NonOS_ErrorOut · SC1_R+/COMP1_Pr+ · SC1_B+/COMP1_Pb+ · COMP2_Pr+ · COMP2_Pb+
Page 32 of the LG Electronics 463 user manual — USB DOWN STREAM
Page 32 · click to enlarge
Page 32
LG Electronics 463 — #EV# diagram (page 32)
Fig. 46

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. USB_OCP_DIODE_1EA

USB1_CTL

LG Electronics 463 — USB1_CTL diagram (page 32)
Fig. 47

EAN61849601

AP2191DSG

MLB-201209-0120P-N2

USB1_DIODES

L1451-*1

3AU04S-305-ZC-(LG)

USB_1_32LS3500

JK1450-*1

1 2 3 4 5

USB DOWN STREAM

3AU04S-345-ZC-H-LG

USB (SIDE)

Page 34 of the LG Electronics 463 user manual — PPJ234-05
Page 34 · click to enlarge
Page 34
LG Electronics 463 — #EV# diagram (page 34)
Fig. 48

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. REAR_JACK_EU(ERRC)

EU_OPT

R2806

EU_OPT

R2802

EU_OPT

R2803

EU_OPT

R2804

470K

EU_OPT

R2805

+3.3V_Normal

0.1uF 16V

OPT

D2810

470K

R2831

+3.3V_Normal

10K

R2832

10K

OPT

OPT

R2841

OPT

D2809

10K

D2818

R2837

10K

OPT

D2806

D2808

D2807

D2800

OPT

D2801

EU_OPT

D2802

OPT

D2803

OPT

D2804

OPT

D2805

OPT

OPT

OPT

OPT

R2826

470K

R2825

470K

R2823

R2824

R2822

D2815

D2814

OPT

D2816

OPT

OPT

D2813

OPT

D2812

OPT

D2817

OPT

Full Scart

5E [RD]O-SPRING_2

4E [RD]CONTACT_2

4C [RD]CONTACT_1

5C [RD]O-SPRING_1

5D [WH]O-SPRING

7C [RD]E-LUG-S

5B [BL]O-SPRING

7B [BL]E-LUG-S

4A [GN]CONTACT

5A [GN]O-SPRING

6E [RD]E-LUG

6A [GN]E-LUG

COMPONENT

1 AUDIO_R_OUT 2 AUDIO_R_IN 3 AUDIO_L_OUT 4 AUDIO_GND 5 B_GND 6 AUDIO_L_IN 7 B_OUT 8 ID 9 G_GND 10 D2B_IN 11 G_OUT 12 D2B_OUT 13 R_GND 14 RGB_GND 15 R_OUT 16 RGB_IO 17 SYNC_GND1 18 SYNC_GND2 19 SYNC_OUT 20 SYNC_IN 21 COM_GND 22 AV_DET

PPJ234-05

JK2803

PSC008-01

JK2801

EU_OPT

1000pF 50V · 1000pF 50V

Page 35 of the LG Electronics 463 user manual — 12507WS-04L
Page 35 · click to enlarge
Page 35
LG Electronics 463 — #EV# diagram (page 35)
Fig. 49

12507WS-04L

+3.5V_ST P1000

GND

2 PM_RXD

3 GND

4 PM_TXD

PM_RXD

PM_TXD

RS-232C 4PIN

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Page 36 of the LG Electronics 463 user manual — RGB_DDC_SCL
Page 36 · click to enlarge
Page 36
LG Electronics 463 — #EV# diagram (page 36)
Fig. 50

RGB_DDC_SCL

RGB_DDC_SDA

MSTAR_DEBUG_4P 1

12505WS-04A00

P1

MSTART DEBUG_4PIN

THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

Page 37 of the LG Electronics 463 user manual — #EV#
Page 37 · click to enlarge
Page 37
Page 37 of the LG Electronics 463 user manual — #EV#
Page 38 of the LG Electronics 463 user manual — No. Error symptom (High category) Error symptom (Mid category) Page Remarks
Page 38 · click to enlarge
Page 38

First of all, Check whether there is SVC Bulletin in GCSC System for these model.

No. Error symptom (High category) Error symptom (Mid category) Page Remarks

Contents of LCD TV Standard Repair Process

3 Tuning fail, Picture broken/ Freezing 3, 4

9 Wrecked audio/discontinuation/noise 10

10 D. Function error Remote control & Local switch checking 11

11 External device recognition error 12

12 E. Noise Circuit noise, mechanical noise 13

13 F. Exterior error Exterior defect 14

No video/Normal audio 1

2 No video/No audio 2

4 Color error 5

light spot, external device color error 6

B. Power error No power 7

auto on/off 8

8 C. Audio error No audio/Normal video 9

5 Vertical/Horizontal bar, residual image,

7 Off when on, off while viewing, power

A. Video error

Page 39 of the LG Electronics 463 user manual — No. Error symptom Content Page Remarks
Page 39 · click to enlarge
Page 39

Contents of LCD TV Standard Repair Process Detail Technical Manual

Continue to the next page

17 Exchange LED driver Board (PSU) A-3/5 55” : driver board Other : PSU

No. Error symptom Content Page Remarks

Exchange T-Con Board (1) A-1/5

16 Exchange T-Con Board (2) A-2/5

18 Exchange Module itself (1) A-4/5

19 Exchange Module itself (2) A-5/5

ADJ Key A10

ADJ Key A10

Check LCD back light with naked eye A1

2 LED driver B+ 24V measuring method A2

3 Check White Balance value A3

4 Power Board voltage measuring method A4

TUNER input signal strength checking method A5

7 LCD-TV Version checking method A6

LCD TV connection diagram A7

condition A8

LCD TV connection diagram A8

condition A8

10 Check Link Cable (LVDS) reconnection

13 Check Link Cable (LVDS) reconnection

11 Adjustment Test pattern -

14 Adjustment Test pattern -

A. Video error_Vertical/Horizontal bar,

Defected Type caused by T-Con/

A. Video error_ No video/Normal

6 A. Video error_ No video/Video

residual image, light spot

error

A. Video error_Color

Inverter/ Module

<Appendix>

lag/stop

audio

Page 40 of the LG Electronics 463 user manual — ☞ A4 ☞ A1
Page 40 · click to enlarge
Page 40

Revised date 1/14 LCD TV Error

Board or module

2012. 01 .14

Replace T-con

First of all, Check whether all of cables between board is inserted properly or not.

Balance value before replacing the Main Board Replace Main Board Re-enter White Balance value

Y

Established

Repair Power

Board or parts Check Power Board 24v output

Normal

End

date

voltage

N

voltage Y Replace Inverter

Check Power

12v,3.5v etc.

☞ A4 ☞ A1

(Main B/D ↔ Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable,,,)

or module

Board

No video/ Normal audio

symptom A. Video error

On with naked eye On Y

Repair Power

Board or parts

N

Normal

N

Normal audio Check Back Light

Always check & record S/W Version and White

audio Y

video/No audio

☞ A6 & A3

Normal

N

Move to No

Standard Repair Process

※ Precaution

No video

Page 41 of the LG Electronics 463 user manual — Revised date 2/14 LCD TV Error
Page 41 · click to enlarge
Page 41

Revised date 2/14 LCD TV Error

symptom 2012 . 01 .14

Established

N End

date

Check and

MAIN B/D

replace

A. Video error

No video/ No audio

Y

Board and repair

Replace Power

voltage?

Normal

parts

Board ( 3.5V,12V,20V

voltages of Power

Check various

or 24V…)

No Video/

No audio

Standard Repair Process

Page 42 of the LG Electronics 463 user manual — → DVD Player ,Set-Top-Box, Different maker TV etc`
Page 42 · click to enlarge
Page 42

Close

Revised date 3/14 LCD TV Error

Y

Main B/D

Normal

Picture?

N N

Replace

symptom 2012. 01 .14

Tuner soldering

Check

Established

date

N

N

S/W Upgrade

Bulletin?

Normal

Picture?

SVC

Y

Close

Y

Check whether other equipments have problem or not.

→ DVD Player ,Set-Top-Box, Different maker TV etc`

Picture broken/ Freezing

(By connecting RF Cable at other equipment)

A. Video error

( Menu → Set up → Support → Signal Test )

S/W Version

Check

- Signal strength (Normal : over 50%)

. By using Diagnostics menu on OSD

- Signal Quality (Normal: over 50%)

Contact with signal distributor

or broadcaster (Cable or Air)

. By using Digital signal level meter

Y

Normal

Picture?

Standard Repair Process

Check RF Signal level

Y

N

Check RF Cable

1. Reconnection 2. Install Booster

Connection

Normal

Signal?

Normal

Picture?

N

Close

Y

Page 43 of the LG Electronics 463 user manual — - Check satellite
Page 43 · click to enlarge
Page 43

Tuner soldering Replace

Main B/D

Revised date 4/14 LCD TV Error

symptom 2012. 01 .14

Check

Y N

S/W Upgrade

N

Established

Bulletin?

Normal

Picture?

date

Y

Close

SVC

Y

S/W Version

Signal? Check

Check whether other equipments have problem or not.

Tuning fail, Picture broken/ Freezing

Check RF signal cable (DVB satellite signal or not)

(By connecting RF Cable at other equipment)

(match with installed ANT)

A. Video error

Change satellite setting

Y

→ Set-Top-Box, Different maker TV etc

N

Normal

setting?

Normal

Picture?

N

Y

Close

- Check Satellite connection

- Check LNB frequency.

(DiSEqC, motor, etc…)

Check satellite setting.

- Check satellite

Standard Repair Process

Check RF Signal level

signal distributor

or broadcaster

Contact with

(Cable or Air)

Normal

N

Close

Page 44 of the LG Electronics 463 user manual — Revised date 5/14 LCD TV Error
Page 44 · click to enlarge
Page 44

Revised date 5/14 LCD TV Error

Replace module

Replace Main B/D

Replace Main B/D

symptom 2012. 01 .14

Y

N

Color

error?

End

Established

Y External device

Y External device

date

Request repair

for external

device/cable

/Cable

normal

N

N

/Cable

normal

Replace Main B/D Color

Check external

Y

device and

device and

external

error?

N

Check

A. Video error

cable

cable

Color error

☞ A8/ A9

and replace

(LVDS) and

Link Cable

※ Check

condition

contact

External Input/

Component

HDMI/DVI

error

RGB/

error

Y

N

Check error

Color

error?

color input

mode

Check color by input

Check Test pattern ☞ A10

-COMPONENT

Standard Repair Process

-External Input

- HDMI/DVI

- RGB

Page 45 of the LG Electronics 463 user manual — RGB and HDMI/DVI by
Page 45 · click to enlarge
Page 45

Replace

Main B/D Screen

Replace

N

Screen

normal?

Y

Main B/D Screen

Replace

Module

End

Revised date 6/14 LCD TV Error

Request repair for

external device

N

N

normal?

Y

normal?

Replace Main B/D

Y

2012. 01 .14

(Check normal operation of

External Input, Component,

Generator ,Set-top Box etc.

error Connect other external

External Input, Component,

Generator ,Set-top Box etc.

RGB and HDMI/DVI by

connecting Jig, pattern

Connect other external

(Check normal operation of

RGB and HDMI/DVI by

connecting Jig, pattern

N

device and cable

Established

normal?

device and cable

date

Screen

Y

End

☞ A7 ☞ A8/ A9

replace Link

Check and

Vertical / Horizontal bar, residual image,

Cable Normal?

Component

light spot, external device color error

External

Input

error

RGB

error

HDMI/

DVI

Request repair

Y

A. Video error

Vertical/Horizontal bar, residual image, light spot

for external

N

device

External device screen error-Color error

Check screen

-External Input

Y Check external

condition by

-Component

- HDMI/DVI

connection

condition

input

- RGB

device

normal?

Screen

N

Replace

module

N Check

N Normal

S/W Upgrade

symptom

version

screen?

Y

Y

End

Check color condition by input

Check Test pattern

Standard Repair Process

Check S/W Version

-External Input

-Component

- HDMI/DVI

- RGB

Page 46 of the LG Electronics 463 user manual — Power LED Replace
Page 46 · click to enlarge
Page 46

Power LED Replace

Power

Revised date 7/14 LCD TV Error

B/D

Replace Main B/D

Y OK?

N

2012. 01 .14

Measure voltage of each output of Power B/D

voltage? Replace Main B/D

operation? Check Power

On ‘”High”

Established

date

Y Normal

Replace Power B/D

N Normal

Y

N

Replace Power

by pressing Power Key

voltage?

Y

Y Normal

N

On Remote control

B. Power error

DC Power on

B/D

No power

Check ST-BY 3.5V

On? Y

was inserted properly

※

N

Check Power cord

Power LED

symptom

Normal?

Close

N

Y

Standard Repair Process

. Stand-By: Red

Check

Page 47 of the LG Electronics 463 user manual — Error? N
Page 47 · click to enlarge
Page 47

Y Normal? End

Revised date 8/14 LCD TV Error

Replace Power B/D

Abnormal "POWEROFF_ABNORMAL1" Power off by abnormal status except CPU trouble

"POWEROFF_UNKNOWN" Power off by unknown status except listed case

N

2012. 01 .14

Status Power off List Explanation

Replace Main B/D Normal

"POWEROFF_REMOTEKEY" Power off by REMOTE CONTROL

"POWEROFF_RESREC" Power off by Reserved Record

"POWEROFF_RECEND" Power off by End of Recording

"POWEROFF_SLEEPTIMER" Power off by SLEEP TIMER

"POWEROFF_SWDOWN" Power off by S/W Download

"POWEROFF_CPUABNORMAL" Power off by CPU Abnormal

Replace Main B/D CPU

"POWEROFF_INSTOP" Power off by INSTOP KEY

"POWEROFF_OFFTIMER" Power off by OFF TIMER

"POWEROFF_AUTOOFF" Power off by AUTO OFF

"POWEROFF_ONTIMER" Power off by ON TIMER

"POWEROFF_RS232C" Power off by RS232C

Established

Replace Power B/D

date

Y

voltage?

N

Abnormal

Abnormal

Off when on, off while viewing, power auto on/off

(If Power Off mode

Check and fix exterior

Check Power B/D

is not displayed)

of Power B/D Part

Check Power Off

voltage

B. Power error

※ Caution

Normal

Mode

* Please refer to the all cases which can be displayed on power off mode.

Error? N

Fix A/C cord & Outlet

and check each 3

Y

phase out

symptom

Standard Repair Process

Check for all 3phase

Check A/C cord

Check outlet

power out

Page 48 of the LG Electronics 463 user manual — Revised date 9/14 LCD TV Error
Page 48 · click to enlarge
Page 48

Revised date 9/14 LCD TV Error

2012. 01 .14

Replace MAIN Board End

Replace Power Board and repair parts

Established

date

Y

Normal

voltage

N

N

Replace Speaker

Disconnection

Check audio B+

Y

24V of Power Board

No audio/ Normal video

C. Audio error

☞ A15 ☞ A16

disconnection

Speaker off Off N

Cancel OFF

Speaker

Y

Check

Check user

menu >

symptom

Standard Repair Process

Screen normal

No audio

Page 49 of the LG Electronics 463 user manual — Replace Main B/D
Page 49 · click to enlarge
Page 49

End

Revised date 10/14 LCD TV Error

→abnormal audio/discontinuation/noise is same after “Check input signal” compared to No audio

Replace Main B/D

B+ Voltage (24V)

Y

2012. 01 .14

Check audio

voltage?

Replace Power B/D

Normal

Check and fix external device

N

N

Normal

audio?

Y

Established

date

Check and replace

Replace Main B/D N

Connect and check

speaker and

connector

other external

device

Wrecked audio/ discontinuation/noise

Wrecked audio/

Discontinuation/

Wrecked audio/

Discontinuation/

Wrecked audio/

Discontinuation/

for External Input

Wrecked audio/

Discontinuation/

Noise only

for D-TV

Noise only

for Analog

Noise only

Noise for

all audio

C. Audio error

Request repair to external

(When RF signal is not

cable/ANT provider

External Input

Check and fix

external device

(In case of

signal error)

received)

Y

symptom

normal?

Signal

Standard Repair Process

-External Input

Check input

signal

signal

-RF

Page 50 of the LG Electronics 463 user manual — If R/C operate,
Page 50 · click to enlarge
Page 50

Replace

Main B/D

Y ☞ A17

Repair/Replace

Revised date 11/14 LCD TV Error

Output signal Normal

Signal?

N

IR B/D

symptom 2012. 01 .14

Check IR

(Power B/D don’t have problem)

Check 3.5v on Power B/D

Replace Power B/D or

Y

Replace Main B/D

Established

date

Voltage?

Normal

N

3.5V On Main B/D

Check B+

Remote control & Local switch checking

D. Function error

N

operating?

Normal

Y

Close

1. Remote control(R/C) operating error

Cable connection

Connector solder

Check & Repair

Close

Check & Replace

Baterry of R/C

Replace R/C

operating?

Normal

N

Y

operating?

Operation Normal

N

Standard Repair Process

Check R/C Operating

Explain the customer

cause is interference

When turn off light

from light in room.

If R/C operate,

Check R/C itself

in room

Page 51 of the LG Electronics 463 user manual — Revised date 12/14 LCD TV Error
Page 51 · click to enlarge
Page 51

Revised date 12/14 LCD TV Error

2012. 01 .14

Replace Main B/D

Replace Main B/D Fix in

Established

date

External Input and

Recognition error

Recognition error

Component

RGB,HDMI/

DVI, Optical

External device recognition error

N

information?

with technical

D. Function error

Technical

accordance

information

Y

Check technical

- Fix information

- S/W Version

information

external device/cable

Y

Check and fix

Signal

input?

N

symptom

Standard Repair Process

Check

signal

input

Page 52 of the LG Electronics 463 user manual — Standard Repair Process
Page 52 · click to enlarge
Page 52

Revised date 13/14 LCD TV Error

※ When the nose is severe, replace the module

then proceed as shown in the solution manual

2012. 01 .14

(For models with fix information, upgrade the

cabinet, refer to the KMS fix information and

※ If there is a “Tak Tak” noise from the

(For models without any fix information,

S/W or provide the description)

Established

provide the description)

date

Replace PSU (with LED driver)

Replace LED driver

Circuit noise, mechanical noise

OR

E. Noise

OR

description. When the customer does not

※ Describe the basis of the description

in “Part related to nose” in the Owner’s

phenomenon, and apply the 1st level

agree, apply the process by stage.

noise Check location

※ Mechanical noise is a natural

location of

of noise

Check

noise

Mechanical

nose type Circuit

noise

symptom

Manual.

Standard Repair Process

Identify

Page 53 of the LG Electronics 463 user manual — Revised date 14/14 LCD TV Error
Page 53 · click to enlarge
Page 53

Revised date 14/14 LCD TV Error

2012. 01 .14

Established

date

Replace remote controller Remote

F. Exterior defect

Replace module Zoom part with

damage Replace cabinet

dent Replace stand

Exterior defect

controller

exterior damage Module

damage

Cabinet

damage

Stand

symptom

Standard Repair Process

Ask about the LG Electronics 463

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the LG Electronics 463

Be the first to ask — other owners or our team will answer.

Original document

LG Electronics 463 manual PDF

53 pages·7.2 MB·Flat Panel Television·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…