
PLASMA TV
MODELS: 42PC3D
32LC2DU 37LC2D 42LC2D
42PC3DV 50PC3D 60PC1D
OWNER’S MANUAL

http://www.lg.ca
ENERGYSTAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA).
Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENER- GY STAR guidelines for energy efficiency. P/NO : 38289U0527F
d · Printed in Korea

WARNING :
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi- cient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as prac- tical.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product.
The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 Phone: 1-800-243-0000 http://www.lgusa.com

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
Safety Instructions · Owner's Manual

Main plug is the disconnecting device.The
plug must remain redily operable.
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discon- tinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
- If the TV feels cold to the touch, there may be a small “flicker” when when it is turned on. This is normal, there is noth-
ing wrong with TV. - Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have
no adverse effect on the monitor's performance. - Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some
temporary distortion effects on the screen.
a. The fluorescent lamp used in this product contains a small amount of mercury. b. Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of your local authority.
Safety Instructions · On Disposal


44 Manual Clock Setup 44 Auto Clock Setup 45 On/Off Timer Setup 45 Sleep Timer 46 Auto Off
Options
47 Aspect Ratio Control 48 Caption/Text 49 Caption Option 49 Low Power (42PC3D/3DV, 50PC3D, 60PC1D Only) 50 ISM (Image Sticking Minimization) Method (42PC3D/3DV, 50PC3D, 60PC1D
Features
51~52 Parental Lock Setup
59~60 IR Codes
61 Programming the Remote
Reference
62~63 Programming Codes
64~65 Troubleshooting Checklist
65 Maintenance
66~67 Product Specifications
Contents · Only) · Lock Menu Options

Ensure that the following accessories are included with your TV. If any accessory is missing, please contact the dealer from where you purchased the product. User must use shielded signal interface cables(D-sub 15 pin cable) with ferrite cores to maintain standard compliance for the product.

Twister Holder Arrange the wires with the twister holder.
Slightly wipe stained spot on the exterior only with the cleansing cloths for the product exterior if
there is stain or fingerprint on surface of the exterior. Do not wipe roughly when removing stain. Please be cautious of that excessive power may cause
Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. 1
Place the hook of the stand in the back of the product as shown. 2
Install the 4 bolts provided securely, in the back of the product. 3
Introduction


- This is a simplified representation of front panel. - This picture shown below may be somewhat different from your TV.
Illuminates red in stand- by mode. Illuminates white when the set is switched on.

- This picture shown below may be somewhat different from your TV.

S-VIDEO Input Provides better picture quality than the video input.
AUDIO Input Connections are available for lis- tening to stereo sound from an external device.
/MONO
VIDEO Input Connects the video signal from a video device.
RGB IN
VIDEO VIDEO AUDIO AUDIO
COMPONENT IN COMPONENT IN
HDMI IN
AV IN 1 AV IN 1 AV OUT AV OUT
OPTICAL 1(DVI)
CABLE IN
(CONTROL & SERVICE)
VIDEO VIDEO AUDIO AUDIO MONO ( ) S-VIDEO S-VIDEO
COMPONENT IN Connect a component video/audio device to these jacks.
RGB IN (PC) Connect the monitor output from a PC to the appropriate input port.
AV OUT Connect a second TV or monitor.
Remote Control Port Connect your wired remote control. AUDIO IN (RGB/DVI) Connect the monitor output from a PC to the appropriate input port.
AV (Audio/Video) IN 1 Connect audio/video output from an external device to these jacks. S-VIDEO Connect S-Video out from an S-VIDEO device.
RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC.
ANTENNA/CABLE IN Connect over-the air signals to this jack. Connect cable signals to this jack.
Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power.
DIGITAL AUDIO OUT Connect digital audio from various types of equip- ment. Note: In standby mode, these ports do not work.
HDMI IN Connect a HDMI signal to 1(DVI) or 2. Or DVI (VIDEO)signal to the 1(DVI) port with a DVI to HDMI cable.
Introduction


- This is a simplified representation of front panel. - This picture shown below may be somewhat different from your TV.
- The TV can be conveniently swivelled on its stand 30° to
the left or right to provide the optimum viewing angle.

- This picture shown below may be somewhat different from your TV.

S-VIDEO Input Provides better picture quality than the video input.


VIDEO Input Connects the video signal from a video device. AUDIO Input Connections are available for listening to stereo sound from an external device.
SERVICE
RGB IN
VIDEO VIDEO AUDIO AUDIO
COMPONENT IN COMPONENT IN
(PC)
HDMI IN
AV IN 1 AV IN 1 AV OUT AV OUT
1(DVI)
OPTICAL
CABLE IN
RS-232C IN
DIGITAL AUDIO
VIDEO VIDEO AUDIO AUDIO MONO ( ) S-VIDEO S-VIDEO
OUT
COMPONENT IN Connect a component video/audio device to these jacks.
RGB IN (PC) Connect the monitor output from a PC to the appropriate input port.
AV OUT Connect a second TV or monitor.
Remote Control Port Connect your wired remote control. AUDIO IN (RGB/DVI) Connect the monitor output from a PC to the appropriate input port.
AV (Audio/Video) IN 1 Connect audio/video output from an external device to these jacks. S-VIDEO Connect S-Video out from an S-VIDEO device.
RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC.
ANTENNA/CABLE IN Connect over-the air signals to this jack. Connect cable signals to this jack.
Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power.
DIGITAL AUDIO OUT Connect digital audio from various types of equip- ment. Note: In standby mode, these ports do not work.
HDMI IN Connect a HDMI signal to 1(DVI) or 2. Or DVI (VIDEO)signal to the 1(DVI) port with a DVI to HDMI cable.
Introduction

POWER Turns your TV or any other programmed equipment on or off, depending on mode.
TV INPUT In AV1-2, Component 1-2, or RGB-PC, HDMI1/DVI, and HDMI2 input sources, screen returns to the last TV channel.
POWER
DVD
INPUT
TV
VCR
MODE
External input modes rotate in regular sequence: TV, AV1-2, Component 1-2, RGB-PC, HDMI1/DVI or HDMI2.
AUDIO
STB
(AV 1-2, Component 1-2, RGB-PC , HDMI1/DVI or HDMI2 input sources are linked automatically, only if these are con- nected.)
MENU
BRIGHT +
MODE Selects the remote operating mode: TV, DVD, VCR, AUDIO, CABLE, or STB. Select a mode other than TV, for the remote to operate an external device.
MENU Brings up the main menu to the screen.
TIMER
RATIO
INFO
BRIGHT + / - - Adjust brightness on screen.
MUTE FAV
- It turns to the default settings brightness by changing mode
source.
THUMBSTICK (Up/Down/Left/Right/ENTER) Allows you to navigate the on-screen menus and adjust the system settings to your preference.
SAP EZ SOUND EZ PIC CC
EXIT Clears all on-screen displays and returns to TV viewing from any menu.
TIMER G p.45 Lets you select the amount of time before your TV turns itself off automatically.
RATIO G p.47 Changes the aspect ratio.
INFO When you watch the TV, information displays on top of the screen. Not available in Component 1-2, RGB, HDMI1/DVI and HDMI2 mode.
Introduction

VCR/DVD/DVHS/Camcorder BUTTONS Control some video cassette recorders or DVD players ("RECORD" button is not available for DVD player).
POWER
TV
DVD
VCR
MODE
AUDIO
CABLE
STB
VOLUME UP/DOWN Increases/decreases the sound level.
CHANNEL UP/DOWN Selects available channels found with EZ scan and Manual scan.
BRIGHT -
BRIGHT +
MUTE G p.29 Switches the sound on or off.
FAV Use to scroll the Favorite channels.
EXIT
INFO
TIMER
RATIO
NUMBER BUTTONS
— (DASH) Used to enter a program number for multiple program chan- nels such as 2-1, 2-2,etc.
MUTE FAV
FLASHBK Returns to the last channel viewed.
EZ PIC G p.35 Selects a factory preset picture mode depending on the view- ing environment.
SAP EZ SOUND EZ PIC CC
EZ SOUND G p.41 Selects the sound appropriate for the program's character.
SAP Selects MTS sound: Mono, Stereo, and SAP in analog mode. Change the audio language in DTV mode.
CC G p.48 (*In DTV/CADTV mode G p.48) Select a closed caption: Off, CC1~4, Text1~4.
ADJUST Adjusts screen position, size, and phase in PC mode.
Introduction


I Open the battery compartment cover on the
TV INPUT INPUT
TV
POWER
DVD
MODE
VCR
TV INPUT INPUT
TV
POWER
DVD
VCR
TV INPUT INPUT
TV
POWER
DVD
VCR
AUDIO
CABLE
STB
AUDIO
CABLE
MODE
STB
AUDIO
CABLE
MODE
STB
back side and install the batteries matching cor- rect polarity (+with +,-with -).
ENTER
MENU
BRIGHT +
BRIGHT -
ENTER
MENU
BRIGHT +
BRIGHT -
MENU
ENTER
BRIGHT +
EXIT
TIMER
RATIO
INFO
EXIT
TIMER
RATIO
INFO
EXIT
TIMER
RATIO
INFO
I Use a remote control up to 7 meters distance and
I Install two 1.5V AA batteries. Don’t mix old or
30 degree (left/right) within the receiving unit scope.
used batteries with new ones.
I Close cover.
serve environment.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, poten- tially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.
60PC1D




I Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position, loosen the bolts.
Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
I Use a sturdy rope (not provided as parts of the product, must purchase sepa-
rately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.
Introduction


For proper ventilation, allow a clearance of 4inches on each side from the wall.
G Ensure adequate ventilation by following the clearance recommendations.
I This picture shown below may be somewhat different from your TV.
GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.


Connect the cables as necessary. After connecting the cables neat- ly, arrange the cables to the Cable Holder.
To connect an additional equip- ment, see the External equip- ment Connections section.
Do not hold the CABLE MANAGEMENT when moving the product. - If the product is dropped, you may be injured or the product may be broken.

Place the set with the screen facing down on a cushion or soft cloth as shown. Before unfolding the stand, please make sure two locks (A) on the bottom of the stand push outward.
Pull the stand out as shown. After unfolding the stand, please insert and tighten the screws (provided as parts of the product) in the holes (B) on the bottom of the stand.
(B)
* Image shown here may be slightly different from your set.
When connecting cables to the set, Do not disengage the lock (C). This may cause the set to fall, causing serious bodily injury and serious damage to the set.
When closing the stand for storage - First remove the screws in the holes (B) on the bottom
of the stand. And then pull two Hooks (D) of the stand bottom and fold the stand into the back of the set. - After folding, push the two Locks (A) of the stand
bottom outward.

(D)
How to arrange the cable (For 50PC3D)
Hold the CABLE MANAGEMENT with both hands and push it as shown.
Connect the cables as necessary. To connect an additional equipment, see the External equipment Connections section.
Reinstall the CABLE MANAGEMENT as shown.
For 60PC1D, 42PC3D/3DV Arrange the cable as shown.


- Antenna or Cable Service without a Cable Box Connection. - For optimum picture quality, adjust antenna direction if needed.
Be careful not to bend the bronze wire when connecting the antenna.
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
- Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides
of the screen may remain visible on the screen.
Connect the RF antenna out socket of the VCR to the Antenna socket on the set.
ANT IN
Connect the antenna cable to the RF antenna in socket of the VCR.
S-VIDEO OUT
OUTPUT SWITCH
(R) AUDIO (L) VIDEO
IN
Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
RGB IN
(PC) (PC)
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
AUDIO IN AUDIO IN (RGB/DVI) (RGB/DVI)
REMOTE REMOTE CONTROL IN CONTROL IN
ANTENNA/ ANTENNA/
1(DVI) 1(DVI)
CABLE IN CABLE IN
RS-232C IN RS-232C IN (CONTROL (CONTROL & SER & SERVICE) VICE)
VCR
Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
S-VIDEO OUT
ANT OUT
(R) AUDIO (L) VIDEO
OUTPUT SWITCH
IN
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
Select AV1 input source using the INPUT button on the remote control. - If connected to AV IN2, select AV2 input source.
VIDEO VIDEO AUDIO AUDIO
OPTICAL PTICAL
DIGITAL AUDIO
OUT OUT
VIDEO VIDEO AUDIO AUDIO MONO ( ) S-VIDEO S-VIDEO
Installation

VCR
Connect the S-VIDEO output of the VCR to the S- VIDEO input on the set. The picture quality is improved; compared to normal composite (RCA cable) input.
S-VIDEO OUT
(R) AUDIO (L) VIDEO
ANT OUT
OUTPUT SWITCH
IN
Connect the audio outputs of the VCR to the AUDIO input jacks on the set.
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
AV IN 1 AV OUT COMPONENT COMPONENT IN
Select AV1 input source with using the INPUT button on the remote control. - If connected to AV IN2, select AV2 input source.
DIGIT DIGIT AL AL AUDIO AUDIO OUT
VIDEO AUDIO AUDIO MONO ( ) S-VIDEO S-VIDEO
Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.
Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).
Select AV2 input source with using the INPUT button on the remote control. - If connected to AV IN1 input, select AV1 input
source.
Operate the corresponding external equipment. Refer to external equipment operating guide.
Installation · Camcorder · Video Game Set

DVD
S-VIDEO (R) AUDIO (L)
VIDEO VIDEO AUDIO AUDIO
AV IN 1 V IN 1 AV OUT V OUT COMPONENT COMPONENT IN IN
DIGIT DIGIT AL AL AUDIO AUDIO OUT OUT
VIDEO VIDEO AUDIO AUDIO MONO ( ) S-VIDEO S-VIDEO
Connect the S-VIDEO output of the DVD to the S-VIDEO input on the set.
Connect the audio outputs of the DVD to the AUDIO input jacks on the set.
Turn on the DVD player, insert a DVD.
Select AV1 input source with using the INPUT button on the remote control. - If connected to AV IN2, select AV 2 input source.
Refer to the DVD player's manual for operating instructions.
HDMI IN HDMI IN
1(DVI)
ANTENNA/ ANTENNA/
CABLE IN CABLE IN
DVD
HDMI-DVD OUTPUT
Connect the HDMI output of the DVD to the HDMI IN 1(DVI) or 2 jack on the set.
Select HDMI1/DVI or HDMI2 input source with using the INPUT button on the remote control.
Refer to the DVD player's manual for operating instructions.
Installation


Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the set.
Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the set.
Select Component 1 input source with using the INPUT button on the remote control. - If connected to COMPONENT IN 2, select Component 2 input source.
Refer to the DVD player's manual for operating instructions.
Y PB PR Component ports on the TV

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if
you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
SERVICE SERVICE
RGB IN RGB IN
(PC) (PC)
AUDIO IN AUDIO IN (RGB/DVI) (RGB/DVI)
REMOTE REMOTE CONTROL IN CONTROL IN
Connect the HDMI output of the digital set-top box to the HDMI IN 1(DVI) or 2 jack on the set.
1(DVI)
Select HDMI1/DVI or HDMI2 input source with using the INPUT button on the remote control.
RS-232C IN RS-232C IN (CONTROL (CONTROL & SER & SERVICE) VICE)
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
Connect the video outputs (Y, PB, PR) of the digi- tal set-top box to the COMPONENT IN VIDEO jacks on the set.
Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO jacks on the set.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
Select Component 1 input source with using the INPUT button on the remote control. - If connected to COMPONENT IN 2, select
AV IN 1 V IN 1 AV OUT V OUT COMPONENT COMPONENT IN
Component 2 input source.
DIGIT DIGIT AL AL AUDIO AUDIO OUT OUT
VIDEO VIDEO AUDIO AUDIO MONO ( ) S-VIDEO S-VIDEO

SERVICE SERVICE
RGB IN RGB IN
(PC) (PC)
AUDIO IN AUDIO IN (RGB/DVI) (RGB/DVI)
REMOTE REMOTE CONTROL IN CONTROL IN
HDMI IN HDMI IN
1(DVI) 1(DVI)
RS-232C IN RS-232C IN (CONTROL (CONTROL & SER & SERVICE) VICE)
Connect the DVI output of the digital set-top box to the HDMI IN 1(DVI) jack on the set.
Connect the audio outputs of the set-top box to the AUDIO IN(RGB/DVI) jack on the set.
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
Select HDMI1/DVI input source with using the INPUT button on the remote control.
Installation · Digital Set-top Box

- The TV has a special signal output capability which allows you to hook up a second TV or monitor.
AV IN 1 V IN 1 AV OUT V OUT COMPONENT COMPONENT IN
Connect the second TV or monitor to the TV’s AV OUT jacks.
See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings.
VIDEO VIDEO AUDIO AUDIO MONO ( ) S-VIDEO S-VIDEO
(R) AUDIO (L) VIDEO
Digital Audio Output
- Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output Optical port.
AV IN 1 V IN 1 AV OUT V OUT COMPONENT IN
Connect one end of an optical cable to the TV Digital Audio Optical Output port.
Connect the other end of the optical cable to the digital audio optical input on the audio equipment.
DIGIT DIGIT AL AL AUDIO AUDIO OUT OUT
VIDEO VIDEO AUDIO AUDIO MONO ( ) S-VIDEO S-VIDEO
See the external audio equipment instruction manual for operation. When connecting with external audio equip- ments, such as amplifiers or speakers, please turn the TV speakers off. (Refer to p.43)
Installation · 1/2

- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
RGB IN
Connect the RGB output of the PC to the RGB IN (PC) jack on the set.
AUDIO IN AUDIO IN (RGB/DVI) (RGB/DVI)
REMOTE CONTROL IN CONTROL IN
Connect the PC audio outputs to the AUDIO IN(RGB/DVI) jack on the set.
RS-232C IN RS-232C IN (CONTROL (CONTROL & SER & SERVICE) VICE)
Turn on the PC and the set.
Select RGB-PC input source with using the INPUT button on the remote control.
AUDIO
RGB-PC OUTPUT
When connecting with a HDMI to DVI cable
SERVICE SERVICE
RGB IN RGB IN
(PC)
AUDIO IN (RGB/DVI)
REMOTE REMOTE CONTROL IN CONTROL IN
HDMI IN HDMI IN
1(DVI) 1(DVI)
RS-232C IN (CONTROL & SERVICE)
DVI-PC OUTPUT
AUDIO PC
Connect the DVI output of the PC to the HDMI IN 1(DVI) jack on the set.
Connect the audio outputs of the PC to the AUDIO IN(RGB/DVI) jack on the set.
Turn on the PC and the set.
Select HDMI1/DVI input source with using the INPUT button on the remote control.
Installation

1. Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. 2. When Source Devices connected with HDMI/DVI Input, output PC Resolution (VGA, SVGA, XGA, WXGA), Position and Size may not fit to Screen.Press the ADJUST button to adjust the screen Position of TV SET and contact an PC graphics card service center. 3. When Source Devices connected with HDMI/DVI Input, output TV SET Resolution (480p, 720p, 1080i. 1080p) and TV SET Display fit EIA/CEA- 861-B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service center. 4. In case HDMI/DVI Source Devices is not connect- ed Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI/DVI Input. In case that Video Resolution is not supported TV SET output in HDMI/DVI Source Devices, "INVALID FORMAT" OSD display. Refer to the Manual of HDMI/DVI Source Devices or contact your service center.
5. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC, HDMI/DVI mode. If noise is present, change the PC or HDMI/DVI mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. 6. Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the screen. 7. The synchronization input form for Horizontal and Vertical frequencies is separate.

Installation

- When RGB connect to PC input and select the RGB-PC, this function is used. - When HDMI/DVI connect to PC input and select HDMI/DVI input, this function is used. - After connecting RGB-PC or HDMI/DVI to PC input and checking the screen quality.

SAP EZ SOUND EZ PIC CC
ADJUST
ADJUST
Press the ADJUST button and then use D / E button to select Resolution, POSITION, SIZE, or PHASE.
Position This function is to adjust
picture to left/right and up/down as you prefer.
Size This function is to minimize any vertical bars or stripes visible on the screen back- ground. And the horizontal screen size will also change.
Press ENTER button.
Phase This function allows you to remove any horizontal noise and clear or sharpen the image of characters.
* When you change the resolution, select the proper resolution in present input to see the best picture appearance.
Resolution This function allows you
select Resolution of XGA/WXGA.

SAP EZ SOUND EZ PIC CC
ADJUST
ADJUST
- To initialize the adjusted values
Press the ADJUST button and then use D / E button to select the RESET option.
Press ENTER button and then use F / G button to select Yes.
Press ENTER button.
Installation · Mini Glossary

Basic operation Basic operation
In standby mode to turn TV on, press the , INPUT, CH D / E button on the TV or press the POWER, TV INPUT, INPUT, CH D / E, Number (0 ~ 9) button on the remote control .
Press the CH D / E or NUMBER buttons to select a channel number.


English Español (Spanish) Français (French)
- The menus can be shown on the
Press the MENU button and then use D / E button to select the OPTION menu.
screen in the selected language. First select your language.
Press the G button and then use D / E button to select Language.
Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the selected language.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.


Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Input Block



Selection ( G or ) leads you to the EZ scan screen.
Processing EZ scan...
TV Ch.20
Press to stop the current scan and start DIGITAL ANTENNA channel scan.
- Automatically finds all channels
available through antenna or cable inputs, and stores them in memory on the channel list.
Press the MENU button and then use D / E button to select the SETUP menu.
Press the G button and then use D / E button to select EZ Scan.
- Run EZ Scan again after any
Antenna/Cable connection changes.
Press the ENTER button to begin the channel search. Allow EZ Scan to complete the channel search cycle for ANTENNA, and CABLE.
- A password is required to gain
access to EZ Scan menu if the Lock System is turned on.


Select channel type and RF-channel number.
TV G 2
TV 2-0
Press to delete the channel.
- A password is required to gain
Press the MENU button and then use D / E button to select the SETUP menu.
access to Manual Scan menu if the Lock System is turned on.
Press the G button and then use D / E button to select Manual Scan.
Press the G button and then use D / E button to select TV, DTV, CATV, and CADTV.
Press the G button and then use D / E button to select channel num- ber you want to add or delete.
Press the ENTER button to add or delete for the channel number.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.



Selection ( G or ) leads you to the channel edit screen.

- There are two different ways in
Press the MENU button and then use D / E button to select the SETUP menu.
order to add or delete scanned channels. One is "Custom List" and the other is "Favorite List" in the channel list. Both of them are available after EZ Scan on the SETUP menu.
Press the G button and then use D / E button to select Channel Edit.
Press the G button. You will now see a screen filled with channel num- bers and a preview picture.
Use D / E / F / G button to select a channel and then use the ENTER button to add or delete it. Press FAV button to add the channel to the Favorite List. The heart-mark will appear in front of that channel num- ber.
- A Custom List can be created by
toggling each channel on or off with ENTER button. The chan- nels in the Custom List are dis- played in black color, and the channels deleted from the Custom List are displayed in gray color. Once a channel is high- lighted you can add or delete the channel by referring to the small window at the top-left corner of the screen.You can create your own Favorite List. Use the FAV button on the remote control when a channel is highlighted and then you can add or delete the channel to/from the Favorite List.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.


- Shows how strong your DTV sig-
Press the MENU button and then use D / E button to select the SETUP menu.
nal is and whether you need to adjust your antenna or digital cable input. The higher the signal strength, the less likely you are to experience picture degrada- tion.
Press the G button and then use D / E button to select DTV Signal.
View the on-screen signal strength monitor to see the quality of the signal being received.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.
input signal is DTV or CADTV, this function is available.
Component1 Component2 RGB-PC HDMI1/DVI HDMI2
- Changes the picture source so
Press the MENU button and then use D / E button to select the SETUP menu.
you can watch your TV, cable TV, VCR, DVD, or any other devices that are connected to your TV.
Press the G button and then use D / E button to select Input Source.
Press the G button and then use D / E button to select the source: TV, AV1, AV2, Component1, Component2, RGB-PC, HDMI1/DVI, or HDMI2.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Component2 Set Top Box
- Sets a label to each input source
Press the MENU button and then use D / E button to select the SETUP menu.
or lets you skip the input source which is not in use when you press INPUT button.
Press the G button and then use D / E button to select Input Label.
Press the G button and then use D / E button to select the source: AV1- 2, Component1-2, RGB-PC, HDMI1/DVI or HDMI2.
Press the F / G button to select the label.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

- EZ Picture adjusts the TV for the best
picture appearance. Select the preset value in the EZ Picture menu based on the program category. - Daylight, Normal, Night Time set-
Press the EZ PIC button repeatedly to select the picture appear- ance setup option as shown below:
Daylight, Normal, Night Time, User 1 and User 2(your own set- tings). • You can also use the VIDEO menu to adjust EZ Picture.
tings are preset for optimum picture quality at the factory and are not adjustable. - In the User 1, and User 2 modes only,
Press the EXIT button to save and return to TV viewing .
user can directly adjust the contrast, brightness, color, sharpness, tint.


XD
- Choose one of three automatic
Press the MENU button and then use D / E button to select the VIDEO menu.
color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue.
Press the G button and then use D / E button to select Color Temperature.
Press the G button and then use D / E button to select either Cool, Medium, Warm, or User.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

XD
Selection ( G or ) leads you to the detailed setting screen.

Press to confirm. MENU
- You can also adjust the detailed set
Press the MENU button and then use D / E button to select the VIDEO menu.
tings(Red, Green, Blue) by selecting the User menu.
Press the G button and then use D / E button to select Color Temperature.
Press the G button and then use D / E button to select User.
Press the G button and then use D / E button to select Red, Green or Blue.
Press the G button and then use F / G button to make appropri- ate adjustments. • The adjustment range of Red, Green or Blue is -20~ +20.
Press EXIT button to return to TV viewing or press MENU but- ton to return to the previous menu.

XD G
- XD is LG Electronic’s unique picture
Press the MENU button and then use D / E button to select the VIDEO menu.
improving technology to display a real HD source through an advanced dig-ital signal processing algorithm. - When selecting EZ Picture options
Press the G button and then use D / E button to select XD.
Press the G button and then use D / E button to select Auto or Manual.
(Daylight, Normal and Night time), XD is automatically change to Auto. - When selecting EZ Picture options
* Selecting the Manual 1. Press the G button and then use F / G button to select XD Contrast, XD Color or XD Noise. XD Contrast:Optimizing the contrast automatically according to the brightness of the reflection. XD Color:Adjusting the colors of the reflection automatically to reproduce as closely as possible to the natural colors. XD Noise:Removing the noise up to the point where it does not damage the original picture.
(User 1 and User 2), you can choose the Auto / Manual and when selecting Manual, you can adjust the XD Contrast, XD color and XD Noise.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.


XD
Cinema 3:2 Mode Off
Press the MENU button and then use D / E button to select the VIDEO menu.
appearance for viewing movies. When you operate Cinema (3:2 Pull- Down Mode or Cinema Correction Mode),the TV will adjust 24 fps video from movies to 30 fps video for display (This function is only available in
Press the G button and then use D / E button to select Advanced .
Press the G button and then use D / E button to select Cinema 3:2 Mode or Black Level.
Analog, AV1, AV2, Component 480i mode.)
* Selecting the Black Level
of the screen using the black level of the screen. This feature operates only in HDMI1/DVI, HDMI2 or AV1, AV2 mode.
Press the G button and then use D / E button to select On or Off .
Press the G button and then use D / E button to select Low or High.
Low The reflection of the screen gets darker. High The reflection of the screen gets brighter.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.


XD
Video Reset G Selection ( G or ) resets to the factory settings (default).
- Use to quickly reset all the Video
Press the MENU button and then use D / E button to select the VIDEO menu.
menu options to their original fac- tory preset values.
Press the G button and then use D / E button to select Video Reset.
Press the G button to reset the Video menu options to original values.



- Other languages may be available
Press the MENU button and then use D / E button to select the AUDIO menu.
if a digital signal is provided by the broadcasting station.
Press the G button and then use D / E button to select Audio Language.
Press the G button and then use D / E button to select: English, Spanish, or French.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

- EZ Sound lets you enjoy the best
Press the EZ SOUND button repeatedly to select the appropriate
sound without any special adjust- ment because the TV sets the appropriate sound options based on the program content.
sound setup as shown below :
Normal, Stadium, News, Music, Theater and User (your own
settings) .
- Normal, Stadium, News, Music
and Theater are preset for good sound quality at the factory and are not adjustable.
Press EXIT button to save and return to TV viewing.
- When you select the Stadium or
Theater, the AUDIO menu- Balance option is disable and the Balance option is set to 0 automatically. When SRS is On, the Balance option is set to 0 automatically. And when you change the other modes, the balance is restored to the original value set the user.


Normal Stadium News Music Theater User G
Selection ( G or ) leads you to the detailed setting screen.
Press to confirm. MENU
- Adjust the sound in your prefer-
Press the MENU button and then use D / E button to select the AUDIO menu.
ence and surrounded environ- ment.
Press the G button and then use D / E button to select EZ Sound.
Press the G button and then use D / E button to select User.
Press the G button and then use D / E button to select the desired sound option (Treble, Bass or Front Surround).
Press the G button and then use F / G button to make appropriate adjustments.

* Selecting the Front Surround
Press the G button and then use F / G button to select Off or SRS (Sound Retrieval System) TruSurround XT.

Front Surround SRS TruSurround XT
When Off is selected, Audio Balance function is enable and reset the bal- ance as previous.
Press EXIT button to return to TV viewing or press MENU button to
Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement produces an immersive sound experience from standard stereo material.

- Adjust the sound in your preference and surrounded environment.


Press the MENU button and then use D / E button to select the AUDIO menu.

Press the G button and then use D / E button to select Balance.
L R Balance 0
Press the G button and then use F / G button to make appropriate adjustments.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

- Turn TV speakers off if using
Press the MENU button and then use D / E button to select the AUDIO menu.
external audio equipment. Feature turns the TV Speakers option On or Off.
Press the G button and then use D / E button to select TV Speaker.
Press the G button and then use D / E button to select Off or On.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.



Year - Date - - / - - Time - - : -
- If current time setting is wrong,
Press the MENU button and then use D / E button to select the TIME menu.
reset the clock manually.
Press the G button and then use D / E button to select Manual Clock.
Press the G button and then use F / G button to select either the year, date, or time option. Once selected, use the D / E button to set the year, date, and time options.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.
Press the MENU button and then use D / E button to select the TIME menu.
- The current time will be set auto-
matically from a digital channel signal provided by the broadcast- ing station.
Press the G button and then use D / E button to select Auto Clock.
Press the G button and then use D / E button to select On.
- Set the clock manually, if the cur-
rent time is set incorrectly by the auto clock function.
- The factory default value of the
Auto Clock is Off, because a clock information sent each broadcasting station is different.
Press the G button and then use D / E button to select Auto, Off, On, depending on whether or not your viewing area observes Daylight Saving time.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

- Timer function operates only if
Press the MENU button and then use D / E button to select the TIME menu.
current time has been set.
Press the G button and then use D / E button to select Off Timer or On Timer.
- Off-Timer function overrides On-
Timer function if they are set both set to the same time.
Press the G button and then use D / E button to select On. • To cancel On/Off Timer function, select Off.
- The TV must be in standby mode
for the On-Timer to work.
Press the G button and then use D / E button to set the hour.
- If you do not press any button
within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode.
Press the G button and then use D / E button to set the minutes.
For only On Timer function Press the G button and then use D / E button to select the channel at turn-on. Press the G button and then use D / E button to set the sound level at turn-on.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.
Press the TIMER button repeatedly to select the number of minutes. First the Off option appears on the screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.
- The Sleep Timer turns the TV off
at the preset time. Note that this setting is cleared when the TV is turned off.
When the number of minutes you want is displayed on the screen, press the TIMER button. The timer begins to count down from the num- ber of minutes selected.
- You can also set up the Sleep
Timer in the TIME menu.
To check the remaining minutes before the TV turns off, press the TIMER button once.
To cancel the Sleep Timer, press the TIMER button repeatedly to select Off.

TV will be automatically
turned off, in case of No
Signal for 10 minutes.
Auto Off G Off
- If the TV is on and there is no
Press the MENU button and then use D / E button to select the TIME menu.
input signal, the TV turns off automatically after 10 minutes.
Press the G button and then use D / E button to select Auto Off.
Press the G button and then use D / E button to select Off or On.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Selects the proper picture proportion to match the source’s
The screen size is, more enlarged at both sides, to create
image.
a spectacular view.



4:3
Choose Zoom 1 when you want to view the picture with-
Choose 4:3 when you want to view a picture with an original
out any alteration. However, the top and bottom portions
4:3 aspect ratio.
of the picture will be cropped.

4:3
16:9
Adjust the picture horizontally, in a linear proportion to fill the
entire screen.
Choose Zoom 2 when you want the picture to be altered,
both vertically extended and cropped. The picture taking a
halfway trade off between alteration and screen coverage.
16:9

Press the RATIO button repeatedly to select the desired picture format.
aspect ratio to be displayed in a different propor- tion. When 4:3 analog signal is received on the 16:9 TV, personally preferred aspect ratio needs to be specified. - RGB-PC/DVI-PC input source use 4:3 or 16:9
OPTION menu.
aspect ratio.


Off CC 1 CC 2 CC 3 CC 4 Text 1 Text 2 Text 3 Text 4
- Select a caption mode for dis-
Use the CC button repeatedly to select Caption Off, CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4.
playing captioning information if provided on a program. - Analog caption displays informa-
Press EXIT button to save and return to TV viewing.
tion at any position on the screen. - Text displays information, usually
at the bottom position and is used for a data service. - Caption/Text, if provided by the
Press the MENU button and then use D / E button to select the OPTION menu.
Press the G button and then use D / E button to select Caption/Text.
broadcaster, would be available for both digital and analog chan- nels on the Antenna/Cable. - This TV is programmed to
remember the caption/text mode it was last set to, when you turn the power off. - Whe you select the CC1~Text4,
Caption Option must be dis- abled.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.
Off English Spanish French
- Choose the language you want
the DTV/CADTV Captions to appear in.
Press the MENU button and then use D / E button to select the OPTION menu.
Press the G button and then use D / E button to select Caption/Text.
- Other languages can be chosen
for digital sources only if they are included on the program.
Press the G button and then use D / E button to select available cap- tion languages: English, Spanish, or French.
- Caption may not be available
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.
depends if the service is not pro- vided by the digital broadcaster.

- Customize the DTV/CADTV cap-
Press the MENU button and then use D / E button to select the OPTION menu.
tions that appear on your screen.
Press the G button and then use D / E button to select Caption Option.
Press the G button and then use F / G button to select Custom.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.
- Low power reduces the power
Press the MENU button and then use D / E button to select the OPTION menu.
consumption of plasma display.
Press the G button and then use D / E button to select Low Power.
Press the G button and then use D / E button On or Off.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Normal White Wash Orbiter Inversion
- A frozen still picture from a
Press the MENU button and then use D / E button to select the OPTION menu.
PC/video game displayed on the screen for prolonged periods will result in a ghost image ; even though the image is changed. Use our unique method to mini- mize any fixed image on the screen.
Press the G button and then use D / E button to select ISM Method.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcast- ing station. The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be done :
V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only.
For Canada
Ratings for Movies previously shown in theaters:



- Set up blocking schemes to
block specific channels, ratings, and external viewing sources.
- A password is required to gain
access to this menu if the Lock System is turned on.
W For Canada • TV Rating-English / TV Rating-French: Selecting canadian English /French language rating system.
Press EXIT button to return to TV viewing or press MENU button to return to the previous menu.

- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and
control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the TV back panel. - RS-232C connection cables are not supplied with the TV.
(PC)
AUDIO IN (RGB/DVI)
REMOTE REMOTE CONTROL IN CONTROL IN
RS-232C IN RS-232C IN (CONTROL (CONTROL & SER & SERVICE) VICE)
Type of Connector; D-Sub 9-Pin Male ype of Connector; D-Sub 9-Pin Male
No. Pin Name 1 No connection 2 RXD (Receive data) 3 TXD (Transmit data) 4 DTR (DTE side ready) 5 GND 6 DSR (DCE side ready) 7 RTS (Ready to send) 8 CTS (Clear to send) 9 No Connection
7-Wire Configurations (Serial female-female NULL modem cable)
3-Wire Configurations (Not standard)
TV
PC
TV
RXD
2 3 5 4 6 7 8
3 2 5 6 4 8 7
RXD
2 3 5 4 6 7 8
3 2 5 4 6 7 8
TXD GND
TXD GND
DTR DSR
DSR DTR CTS RTS
DTR DSR
DTR DSR
RTS CTS
RTS CTS
RTS CTS

Set ID Set ID
- Use this function to specify a TV ID number. - Refer to ‘Real Data Mapping’. See page 55.
Set ID G 1
Transmission / Receiving Protocol ransmission / Receiving Protocol
* Use a crossed (reverse) cable.
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: First command to control the set.(j,k,m or x) * [Command 2]: Second command to control the set. * [Set ID]: You can adjust the set ID to choose desired monitor ID number in Setup menu. Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected the TV is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol. * [DATA]: To transmit command data. Transmit ‘FF’ data to read status of command. * [Cr]: Carriage Return ASCII code ‘0x0D’ * [ ]: ASCII code ‘space (0x20)’
Command Reference List Command Reference List
COMMAND 1 COMMAND 2 DATA (Hexadecimal)
01. Power k a 0 ~ 1 02. Input Select k b * (Refer to p.55) 03. Aspect Ratio k c * (Refer to p.55) 04. Screen Mute k d 0 ~ 1 05. Volume Mute k e 0 ~ 1 06. Volume Control k f 0 ~ 64 07. Contrast k g 0 ~ 64 08. Brightness k h 0 ~ 64 09. Color k i 0 ~ 64 10. Tint k j 0 ~ 64 11. Sharpness k k 0 ~ 64 12. OSD Select k l 0 ~ 1 13. Remote Control Lock Mode k m 0 ~ 1 14. Treble k r 0 ~ 64 15. Bass k s 0 ~ 64 16. Balance k t 0 ~ 64 17. Color Temperature k u 0 ~ 3 18. ISM Method j p * (Refer to p.57) 19. Low Power j q 0 ~ 1
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
[Command2][ ][Set ID][ ][NG][Data][x]
* The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors.

05. Volume Mute (Command2:e)
G To control volume mute on/off.
G To control Power On/Off of the TV.
You can also adjust mute using the MUTE button on remote control. Transmission
[k][a][ ][Set ID][ ][Data][Cr]
[k][e][ ][Set ID][ ][Data][Cr]
[a][ ][Set ID][ ][OK][Data][x]
* In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function.
[e][ ][Set ID][ ][OK][Data][x]
G To adjust volume.
You can also adjust volume with the volume buttons on remote control.
G To select input source for the TV.
[k][f][ ][Set ID][ ][Data][Cr]
[k][b][ ][Set ID][ ][Data][Cr]
[f][ ][Set ID][ ][OK][Data][x]
G To adjust screen contrast.
[b][ ][Set ID][ ][OK][Data][x]
You can also adjust contrast in the Video menu.
[k][g][ ][Set ID][ ][Data][Cr]
G To adjust the screen format.
[g][ ][Set ID][ ][OK][Data][x]
You can also adjust the screen format using the RATIO button on remote control or in the Option menu. Transmission
[k][c][ ][Set ID][ ][Data][Cr]
G To adjust screen brightness.
You can also adjust brightness in the Video menu.
[k][h][ ][Set ID][ ][Data][Cr]
[c][ ][Set ID][ ][OK][Data][x]
[h][ ][Set ID][ ][OK][Data][x]
* Real data mapping
G To select screen mute on/off.
[k][d][ ][Set ID][ ][Data][Cr]
[d][ ][Set ID][ ][OK][Data][x]

13. Remote Control Lock Mode (Command2:m)
G To adjust the screen color.
G To lock the remote control and the front panel controls on
You can also adjust color in the Video menu.
the set.
[k][i][ ][Set ID][ ][Data][Cr]
[k][m][ ][Set ID][ ][Data][Cr]
[m][ ][Set ID][ ][OK][Data][x]
[i][ ][Set ID][ ][OK][Data][x]
G To adjust treble.
You can also adjust treble in the Audio menu.
G To adjust the screen tint.
You can also adjust tint in the Video menu.
[k][r][ ][Set ID][ ][Data][Cr]
[k][j][ ][Set ID][ ][Data][Cr]
[r][ ][Set ID][ ][OK][Data][x]
[ j ][ ][Set ID][ ][OK][Data][x]
G To adjust bass.
You can also adjust bass in the Audio menu.
[k][s][ ][Set ID][ ][Data][Cr]
G To adjust the screen sharpness.
You can also adjust sharpness in the Video menu.
[k][k][ ][Set ID][ ][Data][Cr]
[s][ ][Set ID][ ][OK][Data][x]
[k][ ][Set ID][ ][OK][Data][x]
G To adjust balance.
You can also adjust balance in the Audio menu.
[k][t][ ][Set ID][ ][Data][Cr]
G To select OSD (On Screen Display) on/off.
[t][ ][Set ID][ ][OK][Data][x]
[k][l][ ][Set ID][ ][Data][Cr]
G To adjust color temperature.
[l][ ][Set ID][ ][OK][Data][x]
You can also adjust color temperature in the Video menu.
[k][u][ ][Set ID][ ][Data][Cr]
[u][ ][Set ID][ ][OK][Data][x]

These functions are available in 42PC3D /3DV, 50PC3D, 60PC1D model only.
G To tune channel to following physical/major/minor number
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][ ][Data4][ ][Data5][Cr]
G To avoid having a fixed image remain on screen.
NTSC air:02~45 NTSC cable: 01~87 ATSC air:02~45 ATSC cable:01~87 Data 1,Data 2: Major Channel Number(two part) or Channel Number(One part)
[ j ][p][ ][Set ID][ ][Data][Cr]
Data1: High byte Data2: Low byte Two part channel number: Major number-Minor number One part channel number: If the channel band is ATSC digital cable, it can be used. In case of using one part channel number, minor channel does not need. Data 3, Data 4: Minor Channel Number Data3: High byte Data4: Low byte Data 5:
[p][ ][Set ID][ ][OK][Data][x]
7 Main Picture 6 Two/One
ed 3 2 1 0 Step
G To control the Low Power function on/off.
You can also adjust Low Power in Option menu.
[ j ][q][ ][Set ID][ ][Data][Cr]
x 0 1 1 0
[q][ ][Set ID][ ][OK][Data][x]
* All data are transmitted by Hexadecimal code *Two/One part Channel: 6th bit This bit is used in a cable-ready system. *Using physical channel: 5th bit If the channel band is NTSC air or NTSC cable, channel tuning can be done by only physical channel. In this case, using phys- ical channel bit must be low(0). But if the channel band is ATSC air or ATSC cable, there are two cases that physical channel enable or disable. If the physical channel sending is meaningful, you should set this bit low(0). If the physical channel sending is meaningless, you should set this bit high(1). Example) 1. Analog channel: NTSC cable, channel number(35), main pic- ture Command: ma 00 23 xx 01attribute(0x01): main picture, two part(it’s not mandatory), using physical channel, NTSC cable ‘xx’ data: don’t care major and minor channel number in case analog channel tuning. 2. Digital channel: ATSC air, channel number(don’t know physi- cal channel, major(30), minor(3)), main picture
Command: ma 00 xx 00 1E 00 03 22 attribute(0x22): main picture, two part, not using physical channel, ATSC air ‘xx’ data: don’t care analog channel number in case digital chan- nel tuning. 3. Digital channel: ATSC air, channel number (physical(20), major (30), minor (5)), main picture
Command: ma 00 14 00 1E 00 05 02 attribute(0x02): main picture, two part, using physical channel, ATSC air.
[a][ ][Set ID][ ][OK][Data0][Data1][Data2][Data3][Data4][Data5][x] [a][ ][Set ID][ ][NG][Data0][x]

G To add and delete the channels
[m][b][ ][Set ID][ ][Data][Cr]
[b][ ][Set ID][ ][OK][Data][x] [b][ ][Set ID][ ][NG][Data][x]
G To send IR remote key code
[m][c][ ][Set ID][ ][Data][Cr]
Data Key code: Refer to page 60.
[c][ ][Set ID][ ][OK][Data][x]
G To select input source for TV. Transmission
AV2
RGB PC
HDMI1/DVI
91 HDMI2
[b][ ][Set ID][ ][OK/NG][Data][x]

G Connect your wired remote control to the Remote Control port on the TV.
Single pulse, modulated with 37.917KHz signal at 455KHz
FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3
G Configuration of frame
Low custom code Lead code
High custom code Data code Data code
C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
9 ms 4.5 ms
0.55 ms
2.25 ms
0.56 ms 0.56 ms
1.12 ms
2.24 ms
The waveform is transmitted as long as a key is depressed.

Code (Hexa) Function Note
0B 0F 98 08 C4 C5 79 0E 10 ~ 19 4C 1A 09 02 03 00 01 1E AA 39 40 41 07 06 44 43 52 4D 5B 0A CB D6 5A D0 BF D4 D5 CE CC 76 77 AF E1 E0
INPUT TV INPUT MULTIMEDIA POWER POWER ON POWER OFF RATIO TIMER Number Key 0~ 9 - (Dash) FLASHBK MUTE VOL D VOLE CH D CH E FAV INFO CC
R/C Button R/C Button R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (TV Input Selection) Discrete IR Code (AV1 Input Selection) Discrete IR Code (AV2 Input Selection) Discrete IR Code (Component1 Input Selection) Discrete IR Code (Component2 Input Selection) Discrete IR Code (RGB-PC Input Selection) Discrete IR Code (HDMI-DVI Input Selection) Discrete IR Code (HDMI2 Input Selection) Discrete IR Code (Only 4:3 Mode) Discrete IR Code (Only 16:9 Mode) Discrete IR Code (Only Zoom1 Mode) R/C Button R/C Button
E
F
G ENTER MENU EZ SOUND EZ PIC EXIT SAP ADJUST TV AV1 AV2 COMPONENT 1 COMPONENT 2 RGB-PC HDMI1/DVI HDMI2 Ratio 4:3 Ratio 16:9 Ratio Zoom BRIGHT - BRIGHT +
Reference

G The remote control is a multi-brand or universal remote control. It can be programmed to operate most
remote-controllable devices of other manufacturers. Note that the remote control may not control all models of other brands.
Test your remote control. To find out whether your remote control can operate the component without programming, turn on the component such as a VCR and press the corresponding MODE button (VCR) on the remote control, while illuminating on the selected component. Test the POWER button to see if the component responds properly. If not, the remote requires pro- gramming to operate the device.
POWER
DVD
TV
VCR
MODE
AUDIO
CABLE
STB
Turn on the component to be programmed, then press the correspond- ing MODE button on the remote control.
MENU
BRIGHT +
Press the MENU and MUTE buttons simultaneously for 2 seconds, the button selected component lights on the remote control. If you don't press any button for 20 seconds, the button selected component will turn off on the remote control. At a moment, you have to repeat from step 2.
EXIT
INFO
Enter a code number using the number buttons on the remote. When pressing the button, the light is blinked at a time. Programming code numbers for the corresponding component can be found on the follow- ing pages. Again, if the code is correct, the device will turn off.
RATIO
VOL CH
MUTE FAV
Press the MENU button to store the code. After blinking twice, this code is stored.
Test the remote control functions to see if the component responds properly. If not, repeat from step 2.
SAP EZ SOUND EZ PIC CC
ADJUST
Reference

Brand Codes Brand Codes Brand Codes Brand Codes
AIWA 034 AKAI 016 043 046 124 125 146 AMPRO 072 ANAM 031 033 103 AUDIO DYNAMICS 012 023 039 043 BROKSONIC 035 037 129 CANON 028 031 033 CAPEHART 108 CRAIG 003 040 135 CURTIS MATHES 031 033 041 DAEWOO 005 007 010 064 065 108 110 111 112 116 117 119 DAYTRON 108 DBX 012 023 039 043 DYNATECH 034 053 ELECTROHOME 059 EMERSON 006 017 025 027 029 031 034 035 036 037 046 101 129 131 138 153 FISHER 003 008 009 010 FUNAI 034 GE 031 033 063 072 107 109 144 147 GO VIDEO 132 136 HARMAN KARDON 012 045 HITACHI 004 018 026 034 043 063 137 150 INSTANTREPLAY 031 033 JCL 031 033 JCPENNY 012 013 015 033 040 066 101 JENSEN 043 JVC 012 031 033 043 048 050 055 060 130 150 152
KENWOOD 014 034 039 043 047 048 LG (GOLDSTAR) 001 012 013 020 101 106 114 123 LLOYD 034 LXI 003 009 013 014 017 034 101 106 MAGIN 040 MAGNAVOX 031 033 034 041 067 068 MARANTZ 012 031 033 067 069 MARTA 101 MATSUI 027 030 MEI 031 033 MEMOREX 003 010 014 031 033 034 053 072 101 102 134 139 MGA 045 046 059 MINOLTA 013 020 MITSUBISHI 013 020 045 046 049 051 059 061 151 MTC 034 040 MULTITECH 024 034 NEC 012 023 039 043 048 NORDMENDE 043 OPTONICA 053 054 PANASONIC 066 070 074 083 133 140 145 PENTAX 013 020 031 033 063 PHILCO 031 034 067 PHILIPS 031 033 034 054 067 071 101 PILOT 101 PIONEER 013 021 048
PORTLAND 108 PULSAR 072 QUARTZ 011 014 QUASAR 033 066 075 145 RCA 013 020 033 034 040 041 062 063 107 109 140 144 145 147 REALISTIC 003 008 010 014 031 033 034 040 053 054 101 RICO 058 RUNCO 148 SALORA 014 SAMSUNG 032 040 102 104 105 107 109 112 113 115 120 122 125 SANSUI 022 043 048 135 SANYO 003 007 010 014 102 134 SCOTT 017 037 112 129 131 SEARS 003 008 009 010 013 014 017 020 031 042 073 081 101 SHARP 031 054 149 SHINTOM 024 SONY 003 009 031 052 056 057 058 076 077 078 149 SOUNDESIGN 034 STS 013 SYLVANIA 031 033 034 059 067 SYMPHONIC 034 TANDY 010 034
TATUNG 039 043 TEAC 034 039 043 TECHNICS 031 033 070 TEKNIKA 019 031 033 034 101 THOMAS 034 TMK 006 TOSHIBA 008 013 042 047 059 082 112 131 TOTEVISION 040 101 UNITECH 040 VECTOR RESEARCH 012 VICTOR 048 VIDEO CONCEPTS 012 034 046 VIDEOSONIC 040 WARDS 003 013 017 024 031 033 034 040 053 054 131 YAMAHA 012 034 039 043 ZENITH 034 048 056 058 072 080 101
Brand Codes Brand Codes Brand Codes Brand Codes
ABC 003 004 039 042 046 052 053 AJIN 112 ANTRONIK 014 ARCHER 005 007 014 024 CABLE STAR 026 CENTURION 092 CENTURY 007 CITIZEN 007 COLOUR VOICE 065 090 COMBANO 080 081 COMTRONICS 019 030 DIAMOND 023 EAGLE 020 030 040 EASTERN 057 062 066 ELECTRICORD 032 GE 072 GEMINI 008 022 025 054 GI 052 074
GOLDEN CHANNEL 030 HAMLIN 049 050 055 HITACHI 052 055 HOSPITALITY 070 077 JERROLD 002 003 004 008 009 010 052 069 074 LG (GOLDSTAR) 001 106 101 005 M-NET 037 MACOM 033 MAGNAVOX 010 012 064 079 MEMOREX 100 MOVIE TIME 028 032 NSC 015 028 038 071 073 OAK 016 031 037 053 PANASONIC 044 047 PARAGON 100 PHILIPS 006 012 013 020
065 085 090 PIONEER 034 051 052 063 076 POST NEWS WEEK 016 PRUCER 059 PTS 011 048 071 072 073 074 PULSAR 100 RCA 047 REGAL 049 050 REGENCY 057 REMBRANT 025 SAMSUNG 102 107 030 068 SCIENTIFIC ATLANTA 003 011 041 042 043 045 046 SHERITECH 022 SIGNAL 030 SIGNATURE 052 SL MARX 030
SPRUCER 047 078 STARCOM 002 004 008 009 STARGATE 008 030 TADIRAN 030 TAEKWANG 110 TAIHAN 105 TANDY 017 TEXSCAN 029 TOCOM 039 040 056 TOSHIBA 100 UNIKA 007 014 024 UNITED CABLE 004 053 UNIVERSAL 005 007 014 024 026 027 032 035 VIEWSTAR 012 015 018 086 087 088 089 ZENITH 100 114 060 093
Reference

Brand Codes Brand Codes Brand Codes Brand Codes
ALPHASTAR DSR 123 AMPLICA 050 BIRDVIEW 051 126 129 CHANNEL MASTER 013 014 015 018 036 055 CHAPARRAL 008 009 012 077 CITOH 054 CURTIS MATHES 050 145 DRAKE 005 006 007 010 011 052 112 116 141 DX ANTENNA 024 046 056 076 ECHOSTAR 038 040 057 058 093 094 095 096 097 098 099 100 122 ELECTRO HOME 089 EUROPLUS 114 FUJITSU 017 021 022 027
PACE SKY SATELLITE 143 PANASONIC 060 142 PANSAT 121 PERSONAL CABLE 117 PHILIPS 071 PICO 105 PRESIDENT 019 102 PRIMESTAR 030 110 111 PROSAT 072 RCA 066 106 REALISTIC 043 074 SAMSUNG 123 SATELLITE SERVICE CO 028 035 047 057
088 090 107 130 137 TOSHIBA 002 127 UNIDEN 016 025 042 043 044 045 048 049 078 079 080 086 101 UNIDEN 135 136 VIEWSTAR 115 WINEGARD 128 146 ZENITH 081 082 083 084 091 120
HOUSTON TRACKER 033 037 039 051 057 104 HUGHES 068 JANIEL 060 147 JERROLD 061 KATHREIN 108 LEGEND 057 LG 001 LUTRON 132 LUXOR 062 144 MACOM 010 059 063 064 065 MEMOREX 057 NEXTWAVE 028 124 125 NORSAT 069 070
085 SCIENTIFIC ATLANTA 032 138 SONY 103 STARCAST 041 SUPER GUIDE 020 124 125 TEECOM 023 026 075 087
Brand Codes Brand Codes Brand Codes Brand Codes
AIWA 014 028 070 096 125 129 139 229 230 AKAI 163 ANAM 003 014 017 023 059 106 189 216 217 235 236 BURMECTER 252 CARVER 086 CLARION 199 DAEWOO 027 053 060 084 102 148 198 221 DENON 015 075 130 143 FANTASIA 071 FINEARTS 022 FISHER 089 099 LG(GOLDSTAR) 001 021 024 029 087 107 108 110 190 191 192 210 211 212 239 HAITAI 034 035 188 222 HARMAN/KARDON 068 INKEL 037 058 062 069 078 079 095 121 122 149 150 151 152 153 154 155 157 158 159 160 189 207 222 224 225 226 227 243 247
JVC 004 013 141 KEC 185 186 187 KENWOOD 038 050 067 089 170 171 197 206 215 222 KOHEL 030 NAD 045 046 LOTTE 014 016 036 098 100 172 173 174 175 176 177 178 179 180 181 183 201 202 208 213 214 219 223 232 238 240 LXI 103 MAGNAVOX 111 MARANTZ 002 018 020 025 034 041 081 090 097 112 MCINTOSH 049 MCS 104 MEMOREX 107 NAD 046 ONKYO 013 040 041 047 048 056 057 132 133 140 OPTIMUS 158 PANASONIC 007 033 064 113 142 220 241 251 PENNEY 104
PHILIPS 026 112 143 PIONEER 039 042 043 063 065 091 093 094 115 123 127 250 QUASAR 113 RCA 080 RCX 092 REALISTIC 103 106 SAMSUNG 124 145 146 182 193 194 195 203 204 244 245 246 SANSUI 011 135 138 144 SANYO 019 083 234 SCOTT 106 186 SHARP 031 032 051 052 072 082 117 119 156 184 199 200 206 209 SHERWOOD 005 006 158 SONY 044 045 109 114 118 126 248 249 TAEKWANG 012 020 073 074 076 077 105 161 162 163 164 165 166 167 168 169 205 231 233 242 TEAC 010 085 106 136 185 187 237 TECHNICS 101 113 128 134 147 218
TOSHIBA 137 THE 061 VICTOR 088 131 WARDS 089 YAMAHA 054 055 066 092 199
Brand Codes Brand Codes Brand Codes Brand Codes
APEX DIGITAL 022 DENON 020 014 GE 005 006 HARMAN KARDON 027 JVC 012 LG 001 010 016 025
MAGNAVOX 013 MARANTZ 024 MITSUBISHI 002 NAD 023 ONKYO 008 017 PANASONIC 003 009
PHILIPS 013 PIONEER 004 026 PROCEED 021 PROSCAN 005 006 RCA 005 006 SAMSUNG 011 015
SONY 007 THOMPSON 005 006 TOSHIBA 019 008 YAMAHA 009 018 ZENITH 010 016 025
Reference

The operation does not work normally.
doesn’t work
turned off
The video function does not work.
No sound
Picture appears
or poor picture
Horizontal/verti-
cal bars or pic-
some channels
Lines or streaks
in pictures • Check antenna (Change the direction of the antenna).
Reference

The audio function does not work.
No sound
No output from one
Unusual sound from inside the
There is a problem in PC mode.
range.
ground & Horizontal Noise &
color
Maintenance Maintenance
- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have
your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please do not use a wet cloth.
If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges.
Reference

60.8 x 40.8 x 16.0 inches
(Width x Height x Depth)
1544.0 x 1035.5 x 408.2 mm
60.8 x 38.4 x 4.7 inches
1544.0 x 977.0 x 119.2 mm
163 pounds / 74.0 kg
137.3 pounds / 62.26 kg
44.4 x 29.5x 15.0 inches
(Width x Height x Depth)
1129.0 x 748.5 x 380.0 mm
44.4 x 27.4 x 4.1 inches
1129.0 x 695 x 103.7 mm
64.4 pounds / 29.2 kg
55.8 pounds / 25.3 kg
44.4 x 29.5x 15.0 inches
(Width x Height x Depth)
1129.0 x 748.5 x 380.0 mm
44.4 x 27.4 x 4.1 inches
1129.0 x 695 x 103.7 mm
62.6 pounds / 28.4 kg
54.0 pounds / 24.5 kg
51.3 x 34.3 x 14.0 inches
(Width x Height x Depth)
1302.6 x 872.0 x 355.8 mm
51.3 x 31.9 x 4.2 inches
1302.6 x 810.0 x 107.7 mm
114.4 pounds / 51.9 kg
95.0 pounds / 43.1 kg
VHF 2 ~ 13, UHF 14 ~ 69,
CATV 1 ~ 135, CADTV 1 ~ 135, DTV 2 ~ 69
32 ~ 104°F (0 ~ 40°C)
-4 ~ 140°F (-20 ~ 60°C)
s• The specifications shown above may be changed without prior notice for quality improvement.

31.9 x 24.8 x 9.3 inches
(Width x Height x Depth)
811 x 630 x 235 mm
31.9 x 22.3 x 4.9 inches
811.0 x 566.8 x 123.5 mm
48.3 pounds / 21.9 kg
40.8 pounds / 18.5 kg
37.2 x 28.7 x 11.3 inches
(Width x Height x Depth)
944 x 729 x 286 mm
37.2 x26.0 x 5.1 inches
944.0 x 659.3 x 129.7 mm
65.0 pounds / 29.5 kg
54.9 pounds / 24.9 kg
41.5 x 32.0 x 11.9 inches
(Width x Height x Depth)
1054 x 813 x 302 mm
41.5 x 29.4x 5.4 inches
1054.0 x 746.0 x 136.8 mm
81.6 pounds / 37.0 kg
67.0 pounds / 30.4 kg
VHF 2 ~ 13, UHF 14 ~ 69,
CATV 1 ~ 135, CADTV 1 ~ 135, DTV 2 ~ 69
32 ~ 104°F (0 ~ 40°C)
-4 ~ 140°F (-20 ~ 60°C)


Common problems, likely causes, and what to do.
| Problem | Possible cause | Remedy | |
|---|---|---|---|
| • This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes. | p.64 | ||
| • Adjust Color in menu option. • Keep a sufficient distance between the product and the VCR. • Try another channel. The problem may be with the broadcast. • Are the video cables installed properly? • Activate any function to restore the brightness of the picture. | p.64 | ||
| • Check for local interference such as an electrical appliance or power tool. | p.64 | ||
| • Station or cable product experiencing problems, tune to another station. • Station signal is weak, reorient antenna to receive weaker station. • Check for sources of possible interference. | p.64 |
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.