Instruction/ maintenance manual of the product 4000 LG Electronics
Go to page of 10
COPYRIGHT © 2007 LG ELECTRONICS USA INC, ALL RIGHTS RESERVED. LG IrisAccess™ 4000: iCAM4000 Quick Start Guide The content of this document is furnished for informational use only , is subject to change without notice, and should not be construed as a commitment by LG Electronics USA Incorporated.
1 P acking List What’ s in the box • iCAM4000 - IrisCamera • P ower Adapter Input: 110~240V AC - 1.5AMP 50/60Hz Output: 12V DC - 5.0AMP • P ower Cable for 110V • CA T5 Ethernet Cable • Qui.
T he iCAM4000 is a two-eye iris camera used to capture the iris images of the user . T he iCAM includes an alignment indicator behind the mirror and voice prompts to assist the user .
• The recommended mounting height for the iCAM4000 is 142cm (56 inches) from the floor to the bottom of the unit. T his mounting height can be adjusted to accommodate the height of the average user at the installed location. • High amounts of ambient light must be avoided.
4 iCAM4000 Installation 206.4 181.6 . 8 4 1 4 0 1 1 HOLE HOLE HOLE HOLE HOLE HOLE HOLE . 6 2 7 5 5 1 210 Dimensions and Screw Holes on the Rear Enclosure 68.5 25 43.5 8 9 . 8 4 1 4 42.9 W all Rotation Part with Front Enclosur e Rear Enclosure Dimensions of iCAM4000 (mm unit) 1.
4. When recessed mounting, leave 6mm (1/4”) of extra space above the mark ed hole so when mounting the back plate it allows the iCAM to slide down onto the installation plate tabs . 5. Route the power line , network line, and other necessary cables through the back plate hole.
Changing the IP Address of the iCAM * Note: The IP Address of each iCAM must be changed individually . Do not connect more than one un-configured iCAM to the network at any one time to avoid IP Address conflicts . Any computer with a web browser which supports graphics (ex.
5. Select Network Settings . 6. Enter the new IP address for the iCAM (default = 192.168.5.100) 7. Enter the new Subnet Mask for the iCAM (default = 255.255.255.0) 8. Enter the new Broadcast Address for the iCAM (default = 192.168.5.255) 9. Enter the new Default Gateway for the iCAM.
Once all iCAMs have been configured Once all iCAMs have been configured, the computer IP Address can then be changed back to its original IP Address or to the new IP Address as required to communicate to the rest of the IrisAccess™ system.
T echnical Support Additional information and T echnical assistance is available on the LG Electronics – Iris T echnology Division’ s support web site at www .
An important point after buying a device LG Electronics 4000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought LG Electronics 4000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data LG Electronics 4000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, LG Electronics 4000 you will learn all the available features of the product, as well as information on its operation. The information that you get LG Electronics 4000 will certainly help you make a decision on the purchase.
If you already are a holder of LG Electronics 4000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime LG Electronics 4000.
However, one of the most important roles played by the user manual is to help in solving problems with LG Electronics 4000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device LG Electronics 4000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
