
37LH55 42LH55 47LH55 55LH55
32CL40 42CL40 47CL40
55LH400C
Please read this manual carefully before operating your set and retain it for future reference. The model and serial number of the TV is located on the back and one side of the TV. Record it below should you ever need service.
Serial:
1-800-243-0000 USA, Consumer User
1-888-865-3026 USA, Commercial User 1-888-542-2623 CANADA
This product qualifies for ENERGY STAR in the “factory default (Home Use)” setting.
LG Customer Information Center
Changing the factory default settings or enabling other fea- tures may increase power consumption that could exceed the limits necessary to quality for ENERGY STAR.
www.lgusa.com / www.lg.ca

WARNING / CAUTION
To prevent fire or shock hazards, do not expose this product to rain or moisture.
DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO
Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera- ture accompanying the appliance.
receiver. - Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV
technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause (harmful) interference, and (2) this device must accept any interference received, including interference that may cause unde- sired operation (of the device). Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.

IMPORTANT SAFETY INSTRUCTIONS
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Do not use this apparatus near water.
Only use attachments/accessories specified by the manufacturer.
Clean only with dry cloth.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus com- bination to avoid injury from tip-over.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Unplug this apparatus during lighting storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power- supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

Never touch this apparatus or antenna during a thunder or lighting storm.
When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.
Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something.
CAUTION concerning the Power Cord: It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC out- let). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable.
As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH.
Power Supply Short-circuit · Breaker

ANTENNAS Outdoor antenna grounding If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of over- head power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna dis- charge unit, connection to grounding elec- trodes and requirements for the grounding electrode. Antenna grounding according to the National Electrical Code, ANSI/NFPA 70
Ventilation Install your TV where there is proper ventila- tion. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places.
Take care not to touch the ventilation open- ings. When watching the TV for a long period, the ventilation openings may become hot.
If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center.
Do not press strongly upon the panel with hand or sharp object such as nail, pencil or pen, or make a scratch on it.
Antenna Lead in Wire
Keep the product away from direct sunlight.
Antenna Discharge Unit (NEC Section 810-20)
Grounding Conductor (NEC Section 810-21)
If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary dis- tortion effects on the screen.
Power Service Grounding Electrode System (NEC Art 250, Part H)
Cleaning When cleaning, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
ON DISPOSAL (Only Hg lamp used LCD TV) The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.
Moving Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV.


APPENDIX
Auto Volume Leveler (Auto Volume) 82 Clear Voice II 83 Preset Sound Setting (Sound Mode) 84 Sound Setting Adjustment - User Mode 85 Balance 86 TV Speakers On/Off Setup 87 Audio Reset 88 Stereo/SAP Broadcasts Setup 89 Audio Language 90 On-Screen Menus Language Selection 91 Caption Mode
Troubleshooting 110 Maintenance 112 Product Specifications 113 IR Codes 115 External Control Through RS-232C 116 Open Source License 122
- Analog Broadcasting System Captions 92 - Digital Broadcasting System Captions 93 - Caption Option 94
- Auto Clock Setup 95 - Manual Clock Setup 96 Auto On/Off Time Setting 97 Sleep Timer Setting 98
Set Password & Lock System 99 Channel Blocking 102 Movie & TV Rating 103 Downloadable Rating 108 External Input Blocking 109
Clock Setting

High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions.
Manufactured under license from Dolby Laboratories. “Dolby “and the double-D symbol are trademarks of Dolby Laboratories.
is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.
This TV contains the detailed calibrations necessary for professional certification by the Imaging Science Foundation. The resulting ISF “day” and “night” modes will then be accessible by the user to experience the best their LG HDTV has to offer. CALIBRATE LIKE A PRO: Sophisticated and detailed calibrations can be made through the ISFccc mode. Detailed calibration requires a licensed technician. Please contact your local dealer to inquire about an ISF certified technician.
Automatically enhances and amplifies the sound of human voice frequency range to help keep dialogue audible when background noise swells.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."
The AV Mode optimizes the picture into Cinema, Sports, and game Mode according to the video and audio content. The viewer has the ability to quickly choose the correct mode for the picture they are viewing.
Displays HDTV programs in full 1920 x 1080p resolu- tion for a more detailed picture.
LG TV include a unique invisible speaker system, tuned by renowned audio expert, Mr. Mark Levinson. Speakers are embedded in strategic spots behind the front cabinet and use minute vibrations to turn the entire front bezel into the speaker system. The result is a clean, polished look, and enhanced audio by increasing the “sweet spot”, giving a wider and richer sound field.
Advance 120Hz panel provides clearer, smoother images, even during fast action scenes creating a more stable structure for a crisper picture.
TruMotion 240Hz displays 240 scenes per second by combining advanced 120Hz technology with scanning backlight. This technology is verified from Intertek &TüV Rheinland.
I When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV
for an extended period, it can become permanently imprinted on the screen. This phenomenon is known as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.
I In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period
(2 or more hours for LCD, 1 or more hours for Plasma).
I Image burn can also occur on the letterboxed
areas of your TV if you use the 4:3 aspect ratio setting for an extended period.

ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below.
RATIO
Q. MENU MENU
SLEEP
POWER
INPUT
ENERGY SAVING
AV MODE RETURN
INFO
VOL CH
FAV
MARK
MUTE
P A G E
LIST
FLASHBK
1.5V 1.5V
Owner’s Manual Power Cord Remote Control,

* Wipe spots on the exterior only with the polishing cloth.
When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance.
* Do not wipe roughly when removing stain. Excessive pressure may cause scratch or discoloration. Polishing Cloth
CD Manual · Batteries

FRONT PANEL INFORMATION
I Image shown may differ from your TV.
32/37/42/47/55LH40, 32/37/42/47/55LH41, 37/42/47/55LH55, 55LH400C

Remote Control Sensor, Intelligent Sensor Adjusts picture according to the surrounding conditions
Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on. (Can be adjusted Power Indicator in the OPTION menu. G p.80)


Intelligent Sensor Adjusts picture according to the surrounding conditions
Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the set is switched on.



AV (Audio/Video) IN Analog composite connection. Supports standard definition video only (480i).
RS-232C IN (CONTROL & SERVICE) PORT Used by third party devices. This port is used for Service or Hotel mode.
HDMI/DVI IN, HDMI IN Digital Connection. Supports HD video and Digital audio. Doesn’t support 480i. Accepts DVI video using an adapter or HDMI to DVI cable (not included).
COMPONENT IN Analog Connection. Supports HD. Uses a red, green, and blue cable for video & red and white for audio.
USB INPUT Used for viewing photos and listening to MP3s.
RGB IN (PC) Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable). AUDIO IN (RGB/DVI) 1/8" (0.32 cm) headphone jack for analog PC audio input.
Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power.
OPTICAL DIGITAL AUDIO OUT Digital optical audio output for use with amps and home theater systems. Note: In standby mode, this port doesn’t work.
ANTENNA/CABLE IN Connect over-the air signals to this jack. Connect cable signals to this jack.

STAND INSTRUCTION (For 32/42/47CL40)
I Image shown may differ from your TV.
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the parts of the STAND BODY with COVER BASE of the TV by using the 4 screws supplied.


Fix the 4 bolts securely using the holes in the back of the TV. 4

G When assembling the desk type stand, make sure
the screws are fully tightened (If not tightened fully, the TV can tilt forward after the product installation). Do not over tighten.

Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.

After removing the stand, install the included protection cover over the hole for the stand. Press the PROTECTION COVER into the TV until you hear it click.

STAND INSTRUCTION (For 32/37/42/47/55LH40, 32/37/42/47/55LH41, 37/42/47/55LH55, 55LH400C)
I Image shown may differ from your TV.
INSTALLATION (Except 55LH40, 55LH41, 55LH55, 55LH400C)
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.

Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the back of the TV.


G When assembling the desk type stand, make sure
the bolt is fully tightened (If not tightened fully, the TV can tilt forward after the product installa- tion). Do not over tighten.

DETACHMENT
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.

Detach the stand from TV. 3
PROTECTION COVER
After removing the stand, install the included protection cover over the hole for the stand. Press the PROTECTION COVER into the TV until you hear it click.

VESA WALL MOUNTING
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. LG recommends that wall mounting be performed by a qualified professional installer.

37LH40, 37LH41, 37LH55, 42LH40, 42LH41, 42LH55, 42CL40, 47LH40, 47LH41, 47LH55, 47CL40
G Screw length needed depends on the wall mount
standard screw specifications, the length of the screws may differ depending on their specifica- tions.
used. For further information, refer to the instruc- tions included with the mount.
G Standard dimensions for wall mount kits are shown
G Do not use screws that do not comply with the
in the table.
VESA standard screw specifications. Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. LG is not liable for these kinds of accidents.
G When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for assembly are provided.
G Do not use screws longer then the standard dimen-
sion, as they may cause damage to the inside to the TV.
G LG is not liable for TV damage or personal injury
when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installa- tion instructions.
G For wall mounts that do not comply with the VESA
G Do not install your wall mount kit while your TV is turned on. It may result in personal

I Image shown may differ from your TV.
PREPARATION
Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section.

Install the CABLE MANAGEMENT CLIP as shown.
Put the cables inside the CABLE MANAGEMENT CLIP and snap it closed. 3


Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section.
Put the cables inside the CABLE MANAGEMENT CLIP and snap it closed. 3

I Image shown may differ from your TV.
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
G Do not mount near or above any type of heat source. CAUTION
G Ensure adequate ventilation by following the clearance recommendations.
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.

ATTACHING THE TV TO A DESK (Except 47/55LH40, 47/55LH41, 47/55LH55, 47CL40, 55LH400C)
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.
1-Screw (provided as parts of the product)
G To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.
I This feature is not available for all models.
- The TV is equipped with a Kensington Security System connector on
the back panel. Connect the Kensington Security System cable as shown below. - For the detailed installation and use of the Kensington Security
System, refer to the user’s guide provided with the Kensington Security System. For further information, contact http://www.kensington.com the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as note- book PCs and LCD projectors. NOTE: The Kensington Security System is an optional accessory.
Stand · Desk

SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND
I You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).
I Image shown may differ from your TV.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.

I Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.
I Use a sturdy rope (sold separately) to tie the product. It is safer to tie
the rope so it becomes horizontal between the wall and the product.

G Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
G To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.

I To prevent damage do not connect to the power outlet until all connections are made between the devices.
I Image shown may differ from your TV.
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections. For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments (Connect to wall antenna socket)
ANTENNA/
CABLE IN
Outdoor Antenna (VHF, UHF)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Be careful not to bend the copper wire when connecting the antenna.
CABLE IN
Cable TV Wall Jack
RF Coaxial Wire (75 ohm)
I To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
I If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
I If the antenna is not installed properly, contact your dealer for assistance.
Copper Wire

I To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
I Image shown may differ from your TV.
This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device.
1. How to connect

Connect the video outputs (Y, PB, PR) of the digital set- top box to the COMPONENT IN VIDEO 1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red).

Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO 1 jacks on the TV. 2
I Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box operation.)
I Select the Component1 input source on the TV using the
INPUT button on the remote control.
I If connected to COMPONENT IN 2 input, select the
Component2 input source on the TV.
Y, CB/PB, CR/PR Supported Resolutions


26.97 23.976 27.00 24.00 33.71 29.97 33.75 30.00 67.432 59.94 67.50 60.00

HDMI Connection
1. How to connect

Connect the digital set-top box to HDMI/DVI IN 1, 2, 3, or 4 jack on the TV.
No separate audio connection is necessary. HDMI supports both audio and video.
(Refer to the owner’s manual for the digital set-top box.)
I Select the HDMI1, HDMI2, HDMI3, or HDMI4 input
source on the TV using the INPUT button on the remote control.
If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the lat- est cables that support HDMI version 1.3.
26.97 23.976 27.00 24.00 33.71 29.97 33.75 30.00 67.432 59.94 67.50 60.00


Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1, 2, or 3 jack on the TV.
Connect the digital set-top box audio output to the AUDIO IN (RGB/DVI) jack on the TV.
(Refer to the owner’s manual for the digital set-top box.)
I Select the HDMI1, HDMI2, or HDMI3 input source on the
TV using the INPUT button on the remote control.
G A DVI to HDMI cable or adapter is required for this con-
nection. DVI doesn't support audio, so a separate audio connection is necessary.

DVD SETUP
Component Connection
1. How to connect


Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO 1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red).
Connect the audio outputs of the DVD to the COMPONENT IN AUDIO 1 jacks on the TV.
I Turn on the DVD player, insert a DVD.
I Select the Component1 input source on the TV using
the INPUT button on the remote control.
I If connected to COMPONENT IN 2 input, select the
Component2 input source on the TV.
I Refer to the DVD player's manual for operating instructions.
Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below.




Connect the AUDIO/VIDEO jacks between TV and DVD. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
I Turn on the DVD player, insert a DVD.
I Select the AV1 or AV2 input source on the TV using the
INPUT button on the remote control.
I Refer to the DVD player's manual for operating instructions.
1. How to connect

Connect the HDMI output of the DVD to the HDMI/DVI IN 1, 2, 3 or 4 jack on the TV.
No separate audio connection is necessary. HDMI supports both audio and video.
I Select the HDMI1, HDMI2, HDMI3, or HDMI4 input
source on the TV using the INPUT button on the remote control.
I Refer to the DVD player's manual for operating instructions.
If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the lat- est cables that support HDMI version 1.3.

VCR SETUP
Antenna Connection

Connect the RF antenna out socket of the VCR to the ANTENNA/CABLE IN sock- et on the TV.
Connect the antenna cable to the RF antenna in socket of the VCR.
I Set VCR output switch to 3 or 4 and then
I Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s manual.)

1. How to connect


Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
I Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
I Select the AV1 input source on the TV using the INPUT
button on the remote control.
I If connected to AV IN 2, select AV2 input source on the TV.

G If you have a mono VCR, connect the audio cable from
the VCR to the AUDIO L/MONO jack of the TV.

OTHER A/V SOURCE SETUP
1. How to connect


Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors. (Video = yellow, Audio Left = white, and Audio Right = red)
2. How to use
I Select the AV2 input source on the TV using
the INPUT button on the remote control.
I If connected to AV IN 1 input, select the AV1
input source on the TV.
I Operate the corresponding external equipment.

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
1. How to connect

Connect the VGA output of the PC to the RGB IN (PC) jack on the TV.
Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the TV.
I Select the RGB-PC input source on the TV using the

DVI to HDMI Connection
1. How to connect

Connect the DVI output of the PC to the HDMI/DVI IN 1, 2, or 3 jack on the TV.
Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the TV.
I Select the HDMI1, HDMI2, or HDMI3 input source on
the TV using the INPUT button on the remote control.
If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the lat- est cables that support HDMI version 1.3.

G To get the the best picture quality, adjust the PC
G The synchronization input form for Horizontal and
graphics card to 1920x1080.
Vertical frequencies is separate.
G Depending on the graphics card, DOS mode may
G Depending on the graphics card, some resolution
not work if a HDMI to DVI Cable is in use.
settings may not allow the image to be positioned on the screen properly.
G In PC mode, there may be noise associated with
G If there are overscan in HDMI-PC 1920x1080,
the resolution, vertical pattern, contrast or bright- ness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
change aspect ratio to Just scan.
G When selecting HDMI-PC, set the “Input Label -
PC” in the OPTION menu.
G Avoid keeping a fixed image on the screen for a
long period of time. The fixed image may become permanently imprinted on the screen.
Horizontal Vertical Frequency(KHz) Frequency(Hz)
31.468 70.09
31.469 70.08
31.469 59.94
37.879 60.31
48.363 60.00
47.776 59.87
47.712 60.015
63.981 60.02
75.00 60.00
1920x1080 RGB-PC 1920x1080 HDMI-PC
66.587 59.934
67.5 60.00


You can choose the resolution in RGB-PC mode. The Position, Phase, and Size can also be adjusted. You can use this function only when the PC resolution is set to 1024X768, 1280X768 or 1360X768.


Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, try using the manual settings or a different resolution or refresh rate on the PC.
I If the position of the image is still not
after Auto adjustment in RGB-PC, you can adjust the Position, Size or Phase.


If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This feature operates only in RGB-PC mode.
vertical bars or stripes visible on the screen background. And the horizontal screen size will also change.
remove any horizontal noise and clear or sharpen the image of characters.


Returns Position, Size, and Phase to the default factory settings. This feature operates only in RGB-PC mode.

USB CONNECTION
IN 4
EXTERNAL EQUIPMENT SETUP
L/MONO R AUDIO VIDEO
AV IN 2
1. How to connect
Connect the USB device to the USB IN jack on the side of TV.
I After connecting the USB IN jack, you use the USB func-
tion. (G p.60)
1 or · Memory Key

Send the TV’s audio to external audio equipment via the Audio Output port. If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL AUDIO OUT terminal on the back of TV to a Home Theater (or amp).

Connect one end of the optical cable to the TV port of OPTICAL DIGITAL AUDIO OUT.
Connect the other end of the optical cable to the digital audio input on the audio equipment.
Set the “TV Speaker option - Off” in the AUDIO menu. (G p.87). See the external audio equipment instruction manual for operation.
2 G When connecting with external audio equipment, such as
amplifiers or speakers, you can turn the TV speakers off in the menu. (G p.87)
G Do not look into the optical output port. Looking at the
G Audio with ACP (Audio Copy Protection) function may

REMOTE CONTROL FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.

Select the amount of time before your TV turns off auto- matically. G p.98
Turns the TV on from standby or off to standby.
Rotates through inputs. Also switches the TV on from standby. G p.54
Opens the list of Quick Menu options. G p.47
Displays the main menu or clears all on-screen displays and return to TV viewing.
See a list of AV devices connected to TV. When you toggle this button, the SIMPLINK menu appears at the screen. G p.58-59
Used to enter a program number for multiple program channels such as 2-1, 2-2, etc.
Controls USB menu (Photo List and Music List.) Controls the SIMPLINK compatible devices.

Navigates the on-screen menus and adjusts the system settings to your preference.
Allows the user to move return one step in an interactive application or other user interaction function.
INFO
Displays channel information at the top of the screen. G p.53
Toggles through preset Video and Audio modes. G p.56
Adjusts the volume.
FAV
Scroll through the programmed Favorite channels. G p.52
Select the input to apply the Picture Wizard settings. G p.71 Use to mark or unmark a photo/music. G p.62, 66
Switches the sound on or off. G p.44
Changes the channel.
Moves from one full set of screen information to the next one.
IOpen the battery compartment cover on the back side and
install the batteries matching correct polarity.
IInstall two 1.5V AAA batteries. Don’t mix old or used bat-
teries with new ones.
IClose cover.
(Up/Down/Left · Right/ENTER)

TURNING ON THE TV
First, connect power cord correctly. And switch the AC power control switch on TV (Except 32/42/47CL40). At this moment, the TV switches to standby mode.
I In standby mode to turn TV on, press the , INPUT, CH (DE or ) button on the TV or press the POWER, INPUT, CH ( or ), Number (0~9) button on the remote control.
Select the viewing source by using the INPUT button on the remote control.
I This TV is programmed to remember which power state it was last set to, even if the power cord is out.
When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.
G If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
G If you do not complete the Initial setting, it will appear whenever the TV is switched on until the Initial
setting procedure is completed.
G If the TV is unplugged once or turn off with the AC power control switch on the TV, reset the Clock function.
Press the CH ( or ) or NUMBER buttons to select a channel number. 1
Adjust the volume to suit your personal preference.

Press the VOL (+ or -) button to adjust the volume.
If you want to switch the sound off, press the MUTE button.
You can cancel the Mute function by pressing the MUTE or VOL (+ or -) button.

This Function guides the user to easily set the essential items for viewing the TV for the first time when pur- chasing the TV. It will be displayed on the screen when turning the TV on for the first time. It can also be acti- vated from the user menus.
I Default selection is “Home Use”. We recommend setting the TV to “Home Use” mode for the best pic-
ture in your home environment.
I “Store Demo” Mode is only intended for use in retail environments. Customers can adjust the “Picture
menu - Picture mode” manually while inspecting the TV, but the TV will automatically return to preset in- store mode after 5 minutes.
I “Store Demo” Mode is an optimal setting for displaying at stores. “Store Demo” mode initializes the TV
to set the image quality.
I You can also adjust Initial Setting in the OPTION menu.
Step3. Time setting
Select Menu Language. 1
Select Auto or Manual.
Select desired time option.
Selecting the environment. Choose the setting mode you want.
Store Demo Home Use
Select [Home Use] to use this TV at home. To use this TV at Store, select [Store Demo].
Before starting, be sure that the TV antenna is connected.
Next Simple Manual Previous INFO i
Check your antenna connection and start Auto Tuning.


Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.

Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently.

F Aspect Ratio G Aspect Ratio: Selects your desired picture format. Picture Mode: Selects the factory preset picture depend on the viewing environment. Sound Mode: Selects the factory preset sound for type of program. Multi Audio: Changes the audio language (Digital signal). SAP: Selects MTS sound (Analog signal). Sleep Timer: Select the amount of time before your TV turns off automatically. Del/Add/Fav: Select channel you want to add/delete or add the channel to the Favorite List. Caption: Select on or off. USB Device: Select “Eject” in order to eject a USB device.
A


CHANNEL SETUP
Auto Scan (Auto Tuning)
Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. Run this function if you change your residence or move the TV. Also, make sure to run this function with the antenna connected during TV broadcasting hours. Auto Tuning memorizes only the channels available at the time.
Check your antenna connection. The previous channel information will be updated during Auto Tuning.
I The TV will ask for a password if parental
Select CHANNEL.
control has been activated (LOCK Menu). Use the password you set up in the LOCK Menu to allow a channel search.
Select Auto Tuning.
I When setting the Auto tuning or Manual
tuning, the number of maximum channel you can store is 1000. It is subject to change depending on the broadcasting signal environment.
Select Yes.
Run Auto tuning.
I Memorizes all the available channels in
Return to the previous menu.


When selecting DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the qual- ity of the signal being received.
I The TV will ask for a password if parental
control has been activated (LOCK Menu). Use the password you set up in the LOCK Menu to allow a channel search.
tuning, the number of maximum channel you can store is 1000. It is subject to change depending on the broadcasting signal environment.


The channels in the Channel Edit List are displayed in black and the channels deleted from the Channel Edit List are displayed in blue. When a channel number is deleted, it means that you will be unable to select it using CH button during TV viewing. If you wish to select the deleted channel, directly enter the channel number with the NUMBER buttons or select it in the Channel Edit menu.
I Keep pressing the button and use the or buttons to move between DTV, TV, CADTV and CATV.
I If the channel list is too long, use the CH

You can check which channels are stored in the memory by displaying the channel list.
This padlock is displayed when the channel is locked with parental control.
DTV
DTV
WATCHING TV / CHANNEL CONTROL
Displaying Channel List
Display the Channel List. 1
LIST
Selecting a channel in the channel list
Select a channel. 1
Switch to the chosen channel number. 2
Paging through a channel list
Turn the pages. 1
CH
P A G E
Return to TV viewing. 2 RETURN
Channel List · Exit

FAVORITE CHANNEL SETUP
Favorite Channels are a convenient feature that lets you quickly select channels of your choice without waiting for the TV to select all the in-between channels. To tune to a favorite channel, press the FAV (Favorite) button repeatedly.


FAVORITE CHANNEL LIST
Displaying the favorite channel list
Display the Favorite channel list. 1 MARK
DTV
DTV
FAV
DTV
Selecting a channel in the favorite channel list
Select a channel. 1
Switch to the chosen channel number. 2
Paging through a favorite channel list
Turn the pages. 1
P A G E
CH
Return to TV viewing. 2 RETURN
Favorite List · Exit

Brief Info shows the present screen information.
Show the Brief Info on the screen.
1 2 3 4 5 6 7
Brief Info Title Test..
DOLBY DIGITAL
Sat, Feb 21, 2009 10:10 AM 11:40 AM
Multilingual Caption D 1080i TV-PG D L S V CC
Multilingual : The program contains two or more audio services. Use the Q.MENU menu to select wanted Audio.
Caption : The program contains one or more caption services. Use the Q.MENU menu to select wanted Closed caption.
Dolby Digital: The program contains a Dolby Digital audio signal in TV and HDMI input source.
4:3 16:9
The original aspect ratio of the video is 4:3 The original aspect ratio of the video is 16:9 (wide)
480i 480p 720p 1080i 1080p
The video resolution is 720x480i The video resolution is 720x480p The video resolution is 1280x720p The video resolution is 1920x1080i The video resolution is 1920x1080p
V-Chip: The program contains V-Chip information. Refer to the LOCK menu: A (Age), D (Dialogue), L (Language), S (Sex), V (Violence), FV (Fantasy Violence)

INPUT LIST
Only these input signals which are connected to a TV can be activated and selected.
I You can also select the desired input source in the INPUT menu. 1
Select the desired input source.


Select a desired input source (except TV). Then, you can select your desired Input Label with using Blue button. G p.55
ie) In case of changing the input label using Blue button
I When new external device is connected, this popup menu is
displayed automatically. If selecting Yes, you can select input source that you want to appreciate.
! New external input is connected. Do you want to use this?
I But, when selecting “SIMPLINK - On”, popup menu for HDMI


This indicates which device is connected to which input port.


AV Mode toggles through preset Video and Audio settings.
Cinema will be selected both for “PIC- TURE menu - Picture Mode” and “AUDIO menu - Sound Mode” respectively.
I If you select “Off” in AV mode, the
“Picture Mode” and “Sound Mode” return to previous selected value.
Press the AV MODE button repeatedly to select the desired source.
You can easily and effectively access the TV information by viewing a simple manual on the TV. During the Simple Manual operation, audio will be muted.
Select the part of the manual you want to see.


The TV can be set up so that it can only be used with the remote control. This feature can be used to prevent unauthorized viewing by locking out the front panel controls. This TV is programmed to remember which option it was last set to even if you turn the TV off.
I In Key Lock ‘On’, if the TV is turned off,
press the r / I, INPUT, CH (DE or ) button on the TV or POWER, INPUT, CH ( ) or NUMBER buttons on the remote control.
‘ Key Lock’ appears on the screen if any button on the front panel is pressed while viewing the TV.

SIMPLINK allows you to control and play other AV devices connected with HDMI cable without additional cables and settings. This TV may work with devices with HDMI-CEC support, but only devices with the
logo are fully supported. SIMPLINK can be turned on and off in the user menus.
E
Select OPTION.
Select SIMPLINK.
Select On or Off.
Return to the previous menu.
G Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of the
SIMPLINK device with the HDMI cable.
G When you switch the Input source with the INPUT button on the remote control, the SIMPLINK device
will stop.
G When you select a device with home theater functionality, the sound output automatically switches to
the home theater speakers and the TV speakers are turned off.
G If a connected SIMPLINK home theater system doesn't play the audio from the TV, connect the DIGITAL
AUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the back of the SIM- PLINK device with an OPTICAL cable.

I Direct Play: After connecting AV devices to the TV, you can directly control the devices and play media with-
out additional settings.
I Select AV device: Enables you to select one of the AV devices connected to TV.
I Disc playback: Control connected AV devices by pressing the , ENTER, G, A, l l, FF and GG buttons.
I Power off all devices: When you power off the TV, all connected devices are turned off.
I Switch audio-out: Offers an easy way to switch audio-out.
will change automatically to turn on mode. (A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does not provide this function) Note: To operate SIMPLINK, an HDMI cable over Version 1.3 with *CEC function should be used. (*CEC: Consumer Electronics Control).



Select the desired device.
Control connected AV devices.

TV viewing: Switch to the previous TV channel regardless of the current mode. DISC playback: Select and play discs. When multiple discs are available, the titles of discs are conveniently displayed at the bottom of the screen. VCR playback: Control the connected VCR. HDD Recordings playback: Control recordings stored in HDD. Audio Out to Home Theater speak- er/Audio Out to TV: Select Home Theater speaker or TV speaker for Audio Out.

ENTRY MODES
When you connect a USB device, this pop up menu is displayed automatically. When the Pop Up menu does not appear, you can select Photo List or Music List in the USB menu. In USB device, you can not add a new folder or delete the existing folder.
Connect the USB device to the USB IN jacks on the side of TV.
I This TV supports JPG and MP3 files.
Select the USB Device menu before removing the USB device.
USB
1 Q. MENU
Select PHOTO LIST or MUSIC LIST.
Select USB Device.
Select Eject.
G Only a USB storage device is recognizable.
G Please connect a USB storage device with cable is
offered by USB maker. If connected with cable is not offered by USB maker or an excessively long cable, the device may not be recognized.
G If the USB storage device is connected through a
USB hub, the device is not recognizable.
G A USB storage device using an automatic recogni-
tion program may not be recognized.
G Some USB storage devices may not be supported
or operate properly.
G A USB storage device which uses its own driver
may not be recognized.
G Please backup important files because data on
USB device may be damaged. Data management is consumer's responsibility and as a result, the man- ufacturer does not cover data damage.
G The recognition speed of a USB storage device
may depend on each device.
G Please do not turn off the TV or unplug the USB
device when the connected USB storage device is working. When such device is suddenly separated or unplugged, the stored files or the USB storage device may be damaged.
G If your USB memory device has multiple partitions,
or if you use a USB multi-card reader, you can use up to 4 partitions or USB memory devices.
G In case of USB storage devices formatted as NTFS,
deletion is not allowable.
G Only use a USB storage device which has normal
music files or image files.
G File alignment method of USB storage device is
similar to Window XP and file name can recognize up to 100 English characters.
G Please use only a USB storage device which was
formatted as a FAT 32 or NTFS file system provid- ed with the Windows operating system. In case of a storage device formatted as a different utility program which is not supported by Windows, it may not be recognized.
G The recommended capacity is 1TB or less for a
USB external hard disk and 32 GB or less for USB memory.
G If a USB external hard disk with a “Energy Saving”
G Please connect power to a USB storage device
function doesn’t work, turn the hard disk off and on again to make it work properly. Refer to the user manual of the application USB external hard disk.
(over 0.5A) which requires an external power sup- ply. If not, the device may not be recognized.
Memory Key

You can view .JPG files from USB storage devices. The On Screen Display on your model may be slightly different.
I You can play JPG files only.
I Only baseline scan is supported among JPG.
I Available JPG size (width x height, pixel): 64 x 64 - 15360 x 8640
Screen Components
Select USB. Select Photo List. 2 1 MENU ENTER ENTER
Moves to upper level folder

Up Folder Drive1 JMJ001
KY101 06/10/2008
KY104 06/19/2008
KY102 04/03/2008
KY105 01/31/2008
JMJ001 01/01/2000
JMJ005 05/13/2008
Total number of marked photos
JMJ006 05/26/2008
1366x768, 125KB
Corresponding buttons on the remote control
JMJ007 02/18/2008
JMJ004 02/18/2008
JMJ008 02/18/2008
Navigation Popup Menu Page Change Mark Exit CH MARK
Current page/Total pages · Up Folder

Photo Selection and Popup Menu

Page 2/3 No Marked Photo List
JMJ001
KY101 06/10/2008
KY104 06/19/2008
KY102 04/03/2008
KY105 01/31/2008
JMJ001 01/01/2000
JMJ005 05/13/2008
JMJ002 06/15/2008
JMJ006 05/26/2008
1366x768, 125KB
JMJ007 02/18/2008
JMJ004 02/18/2008
JMJ008 02/18/2008
Navigation Page Change Mark Exit CH MARK Popup Menu


When you select a file (not folder), this PopUp menu is displayed.
Page 2/3 No Marked Photo List
KY101 06/10/2008
KY102 04/03/2008
G Mark All: Mark all photos on the screen.
JMJ002 06/15/2008
1366x768, 125KB
JMJ004 02/18/2008
Navigation Page Change Mark Exit CH MARK Popup Menu
Select the target folder or drive.

I Use the CH button to navigation in the photo page.
I Use the MARK button to mark or unmark a
photo. When one or more photos are marked, you can view individual photos or a slide show of the marked photos. If no photos are marked, you can view all photos individually or all pho- tos in the folder in a slide show. 4 Select the desired Popup menu.

You can change the Photo List view so that it fills the screen. More operations are available in full screen mode.
Page 2/3 No Marked Photo List
KY103 03/30/2008
KY101 06/10/2008
KY104 06/19/2008
KY102 04/03/2008
KY105 01/31/2008
JMJ001 01/01/2000
JMJ005 05/13/2008
USB
1366x768, 125KB
JMJ006 05/26/2008
JMJ003 04/03/2008
JMJ007 02/18/2008
JMJ004 02/18/2008
JMJ008 02/18/2008
Navigation Page Change Mark Exit CH MARK Popup Menu

Page 2/3 No Marked Photo List
JMJ001
KY101 06/10/2008
KY104 06/19/2008
KY102 04/03/2008
KY105 01/31/2008
JMJ001 01/01/2000
JMJ005 05/13/2008
JMJ002 06/15/2008
JMJ006 05/26/2008
1366x768, 125KB
JMJ007 02/18/2008
JMJ004 02/18/2008
JMJ008 02/18/2008
Navigation Page Change Mark Exit CH MARK Popup Menu
Slideshow BGM Delete Option Hide
The aspect ratio of a photo may change the size of the photo displayed on the screen in full size.
Select the target folder or drive.
Select the desired photos.
Show the Popup menu.
Select View.
I Use the CH button to navigation in the photo page.
The selected photo is displayed in full size.


Select the Slideshow, BGM, (Rotate), Delete, Option, or Hide.
I Use button to select the previous or next photo.
I Use button to select and control the menu on the full-sized screen.
slide show. If no photo is selected, all photos in the cur- rent folder are displayed during slide show.
I Set the time interval of the slide show in Option.
G BGM: Listen to music while viewing photos in full size.
Press F G to set the time interval between slides.
I Set the BGM device and album in Option.
I Rotates the photo 90°, 180°, 270°, 360° clockwise.
I Photo cannot be rotated if its width is greater than
I Use button and ENTER button to set values. Then go to and press ENTER to save the settings.
I You cannot change Music Album while BGM is
G This TV will not be able to decode
G Hide : Hide the menu on the full-sized screen.
I To see the menu again on the full-sized screen, press

You can use the Music List menu to play MP3 files from a USB storage device. This TV cannot play back copy-protected files. The On Screen Display on your model may be slightly different.
Supported music file: *.MP3 Bit rate range 32 Kbps - 320 Kbps • Sampling rate (Sampling Frequency) MPEG1 layer 3: 32 kHz, 44.1 kHz, 48 kHz MPEG2 layer 3: 16 kHz, 22.05 kHz, 24 kHz MPEG2.5 layer 3: 8 kHz, 11.025 kHz, 12 kHz
Screen Components
Select USB. Select Music List. 1 2 MENU ENTER ENTER
Moves to upper level folder

Preview: If any album jacket for the file exists, this jack- et is displayed.
Page 2/3 No Marked
Total number of marked musics
Corresponding buttons on the remote control
Navigation Popup Menu Page Change Mark Exit CH MARK

Music Selection and Popup Menu

Once a song finishes playing, the next selected one will be played. When there are no selected musics to play, the next one in the current fold- er will be played. If you go to a different folder and press the ENTER button, the current music in playback will stop.
Navigation Page Change Mark Exit CH MARK Popup Menu
a music finishes playing, the next selected one will be played automatically.
G Mark All: Mark all musics in the folder.
Navigation Page Change Mark Exit CH MARK Popup Menu

I Use the CH button to navigation in the music page.
I Use MARK button to mark or unmark a music
file. If no music is marked, all the music in the folder will be played in sequence. When one or more music files are marked, the marked music files will be played in sequence. If you want to listen to only one song repeatedly, just mark that one file and play.

I The play information box (as shown below) will automatically
move across the screen when there is no user input to pre- vent a fixed image remaining on the screen for a extended period of time.

NOTE !
G When music is playing, is displayed in front of the music play time.
G A damaged or corrupted music file that does not play displays 00:00 as the play time.
G Music files with copy-protection will not play.
G Press ENTER, A , or RETURN button to stop the screen saver.


This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV. HDMI/RGB-PC input source use 4:3 or 16:9 aspect ratio. But you can select all aspect ratios in HDMI-PC 1920X1080 input. You can select a different aspect ratio depending on input source (analog broadcasting, digital broadcasting, aux).

16:9 Adjust the picture horizontally, in a linear pro- portion to fill the entire screen.
4:3 Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio.


Just Scan Normally the edges of video signals are cropped 1-2%. Just Scan turns off this cropping and shows the complete video. Notes: If there is noise on the edges of the original signal, it will be visible when Just Scan is activated. Just Scan operates only in DTV/CADTV/Component/HDMI-DTV/DVI-DTV (720p/1080i/1080p) input source.
Zoom Choose Zoom when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped.
I When adjusting in Q.MENU menu,
a. or button: Adjust proportion of Zoom. b. or button: Move the image on the screen.

Cinema Zoom Choose Cinema Zoom when you want to enlarge the picture in correct proportion. This enlarges an image with cinemascope aspect ratio (2.35:1) without distortion. Note: When enlarging or reducing the picture, the image may become distorted.
Set By Program Selects the proper picture proportion to match the source’s image.
(4:3 4:3)
I or button: Adjust proportion of Cinema Zoom. The adjustment range is 1-16.
I or button: Move the image on the screen.
(16:9 16:9)



This feature lets you adjust the picture quality of the original image. Use this to calibrate the screen quality by adjusting the Black and White Level etc. You can calibrate the screen quality by easily following each step. When you adjust the image to Low, Recommended or High, you can see the example of the changes you made.
Set the screen above identical to the Recommended sample below.
Set the screen above identical to the Recommended sample below.
With Picture Wizard, you can adjust the picture quality of the original image.
Set the screen above identical to the Recommended sample below.
Set the screen above identical to the Recommended sample below.



Set the screen above identical to the Recommended sample below.

Select input source to apply the settings. 11 MARK
Set the screen above identical to the Recommended sample below.
Save. 12
The current adjustment value is saved to Expert1. i
Finish the Picture Wizard. 13


I If you stop the setting before the final
step, the changes will not be saved to the TV.
ture quality, Energy Saving is changed to Off automatically.
Close


There are factory presets for picture settings available in the user menus. You can use a preset, change each setting manually, or use the Intelligent Sensor.
is changed contrast, brightness, sharp- ness, color and tint automatically.
Sport, and Game Settings are preset for the optimum picture quality at the factory.
Select Intelligent Sensor, Vivid, Standard, Natural, Cinema, Sport, or Game.
picture is automatically adjusted accord- ing to the surrounding conditions.
effect of the video in the retail store. Strengthen the contrast, brightness, color and sharpness for vivid picture.
emphasize dynamic video and primary color (e.g, white, uniform, grass, sky blue etc.) by realizing the optimal screen for sports.
video in detail for video quality expert and general user.

Adjust the picture appearance to suit your preference and viewing situations.
E
Select PICTURE. 1 MENU
PICTURE CONTROL
I When adjusting Energy Saving, Backlight function is disabled.
brightness of LCD panel, to control the brightness of the screen. Adjusting the backlight is recommended when setting the brightness of the set. When decreas- ing the backlight, the brightness of the black becomes darker without any loss in video signal and the power consumption is reduced.
Select Vivid, Standard, Natural, Cinema, Sport, or Game.
Select Backlight, Contrast, Brightness, Sharpness, Color, or Tint.
Make appropriate adjustments.
dient of the video signal. You may use Contrast when the bright part of picture is saturated.
Return to the previous menu.
the signal in the picture. You may use Brightness when the dark part of the pic- ture is saturated.
ness in the edges between the light and dark areas of the picture. The lower the level, the softer the image.
I Color: Adjusts intensity of all colors.
and green levels.
Enter Move PICTURE · Picture Wizard


You can calibrate the screen for each Picture Mode or set the video value according to the special video screen. You can set the video seeing differently for each input. To reset to the factory default after making adjustments to each input source, execute the Picture Reset function for each Picture Mode.


By segmenting categories, Expert1 and Expert2 provide more categories which users can set as they see fit, offering the optimal picture quality for users. This may also be used be a professional to help optimize the TV performance in the environment the TV is in.

I Set to warm to enhance hotter colors such as red, or set to cool to make picture
bluish.
I Adjusts the contrast to keep it at the best level according to the brightness of the
screen. The picture is improved by making bright parts brighter and dark parts darker.
I Adjusts screen colors so that they look livelier, richer and clearer. This feature
enhances hue, saturation and luminance so that red, blue, green and white look more vivid.
I Reduces screen noise without compromising video quality.
Low : Make dark and middle gray level area of the picture brighter. Medium: Express original picture levels. High: Make dark and middle gray level area of the picture darker.
I You can adjust brightness of dark area and middle gray level area of the picture.
Low: The reflection of the screen gets darker. High: The reflection of the screen gets brighter. Auto: Realizing the black level of the screen and set it to High or Low automatically.
I Set black level of the screen to proper level.
I This function enables to select 'Low' or 'High' in the following mode: AV (NTSC-M),
HDMI or Component. Otherwise, 'Black level' is set to 'Auto'.
I Adjust the brightness of the screen to prevent the screen from being too bright.
Dims extremely bright pictures.
I This feature is disabled in “Picture Mode-Vivid, Cinema, Intelligent Sensor”.
I Makes video clips recorded in film look more natural by eliminating judder effect.
I DVD and Blu-ray movies are filmed at 24 frames per second. With LG Real Cinema,
every frame is consistently processed 5 times in 1/24 of a second producing 120 fps with TruMotion or 2 times in 1/24 of a second producing 48 fps without TruMotion, thus totally eliminating the judder effect.
High: Provides smoother picture movement. Low: Provides smooth picture movement. Use this setting for standard use. Off: Use this setting when "High" and "Low" setting result in noise.
I TruMotion works with all inputs except PC mode.
I If you enable "TruMotion", noise may appear on the screen.
If this occurs, set "TruMotion" to "Off".

Standard: Displays standard set of colors. Wide: Increase number of colors used.
I Maximize the utilization of color to increase color quality. Color Gamut
I Show clearer and distinctive yet natural edges in of the video.
I This function is enabled in "Picture Mode - Cinema, Expert". Edge Enhancer
I Convert the color of a different video to HD color.
I This is the function to filter the specific colors of the video.
You can use the RGB filter to set color saturation and hue accurately. Color Filter
*This feature is not available for all models.
I This is the function to express richer color.
I This feature represents rich color as much as conventional video signal.
I This function is enabled in "Picture mode - Cinema, Expert" when xvYCC sig-
nal is inputted through HDMI.
I This is the pattern necessary for expert adjustment.
I This function is enabled in "Picture Mode - Expert" when you watch DTV. Expert Pattern
I Adjusts the overall color of the screen by changing the color of white. a. Method : 2 Points - Pattern: Inner, Outer - Red/Green/Blue Contrast, Red/Green/Blue Brightness:
The adjustment range is -50 - +50. b. Method : 10 Point IRE - Pattern: Inner, Outer - IRE (Institute of Radio Engineers) is the unit to display the size of the video signal
and can be set among 10, 20, 30 - 100. You can adjust Red, Green or Blue accord- ing to each setting. - Luminance: This function displays calculated luminance value for 2.2 gamma. You can
input luminance value you want at 100 IRE, than the target luminance value for 2.2 gamma is displayed at every 10 steps from 10 IRE to 90 IRE. - Red/Green/Blue: The adjustment range is -50 - +50.
I As the tool used by the experts to make adjustments by using the test patterns, this
does not affect other colors but can be used to selectively adjust the 6 color areas (Red/Green/Blue/Cyan/Mgt/Yellow). Color difference may not be distinctive even when you make the adjustments for the general video. Adjusts Red/Green/Blue/Yellow/Cyan, Magenta. - Red/Green/Blue/Yellow/Cyan, Magenta Color: The adjustment range is -30 - +30. - Red/Green/Blue/Yellow/Cyan, Magenta Tint: The adjustment range is -30 - +30. - This feature is disable in RGB-PC and HDMI-PC mode.
*This feature is not available for all models.
I As the technology to reduce the power consumption while keeping the same bright-
ness, this has the effect of reducing power consumption, improvement in contrast.


It reduces the TV’s power consumption by lowering the backlight level. The default factory setting complies with the Energy Star requirements and is adjusted to the comfortable level to be viewed at home. You can increase the brightness of your screen by adjusting the Energy Saving level or by setting the Picture Mode.
Select Auto, Off, Minimum, Medium, Maximum, or Screen Off.
automatically adjusted through Intelligent sensor according to the surrounding conditions.


Settings of the selected picture modes return to the default factory settings.


set the indicator light on the front of the TV to On or Off in standby mode.
the indicator light on the front of the TV to On or Off when the power turns on.


Displays a slide show to explain the various feature of this TV.
4 MENU Return to TV viewing. After a while, Demo Mode starts. If you want to stop the demo, press any button (Except VOL +, - and MUTE button).


Auto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program. Because each broadcasting station has its own signal conditions, volume adjustment may be needed every time the channel is changed. This feature allows users to enjoy stable volume levels by making automatic adjustments for each program.


By differentiating the human sound range from others, it improves the sound quality of voices.


Sound Mode lets you enjoy the best sound without any special adjustment as the TV sets the appropriate sound options based on the program content.
and Game are preset for optimum sound quality at the factory.


Adjust the sound to suit your taste and room situations.
I If sound quality or volume is not at the level
you want, it is recommended to use a separate home theater system or amp to cope with dif- ferent user environments.
patented SRS technology that solves the prob- lem of playing 5.1 multichannel content over two speakers.


Adjust the left/right sound of speaker to suit your taste and room situations.


Turn the TV speakers off if using external audio equipment. In AV, Component, RGB and HDMI with HDMI to DVI cable, the TV speaker can be operational even when there is no video signal. If you wish to use an external Hi-Fi system or a SRS System, turn off the TV’s internal speakers.


Settings of the selected Sound Mode return to the default factory settings.

For Analog only: This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accom- panies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used if the broadcast is only in Mono.




Other languages may be available if a digital signal is provided by the broadcasting station. This feature operates only in DTV/CADTV mode.


The menus can be shown on the screen in the selected language.
Select your desired language. From this point on, the on-screen menus will be shown in the selected language.

CAPTION MODE
Analog Broadcasting System Captions
Captions are provided to help people with hearing loss watch TV. Select a caption mode for displaying cap- tioning information if provided on a program. Analog caption displays information at any position on the screen and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable. This TV is programmed to memorize the caption/text mode which was last set when you turned the power off. This function is only available when Caption Mode is set On.
Select OPTION.
I When selecting Off, Sub-menus for
Analog, DTV, and Digital Option become disabled.
Select Caption.
The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the pro- gram provided for the hearing impaired.
Select On.
Select CC1-4 or Text1-4. 4
The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provid- ed by the broadcaster. 5 RETURN
Return to the previous menu.


Choose the language you want the DTV/CADTV Captions to appear in. Other Languages can be chosen for digital sources only if they are included on the program. This function in only available when Caption Mode is set On.


Customize the DTV/CADTV captions that appear on your screen. This function in only available when Caption Mode is set On.
Customize the Size, Font, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language.


The time is set automatically from a digital channel signal. The digital channel signal includes information for the current time provided by the broadcasting station. Set the clock manually if the current time is set incorrectly by the auto clock function.
Select Auto, Off, or On (depending on whether or not your viewing area observes Daylight Saving time).


If the current time setting is wrong, reset the clock manually. If this TV is unplugged once or turn off with the AC power control switch on the TV, reset the Clock function.
Set the Year, Month, Date, Hour, or Minutes option. 5

This function operates only if the current time has been set. The Off Time function overrides the On Time function if they are both set to the same time. The TV must be in standby mode for the On Time to work. If you do not press any button within 2 hours after the TV turns on with the On Time function, the TV will automatically revert to standby mode. If you turn the TV off using the AC power control switch after setting On Time, the On Time function will not work because the power is blocked.
Feb. 21, 2009 10:10 AM
Repeat F Once G
I To cancel On/Off Time function, select Off.
Select TIME.
I Only for On Time function
Select Off Time or On Time.
Select Input.
Select Repeat.
Select the desired input source.
Select Off, Once, Daily, Mon.~Fri., Mon.~Sat., Sat.~ Sun., or Sun.. 4
When Selecting TV: set the channel at turn-on.
Adjust to sound level at turn-on.
Return to the previous menu.


The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off.
I You can also adjust Sleep Timer in the

Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broad- casting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be done : 1. Set ratings and categories to be blocked. 2. Specify a password 3. Enable the lock
V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to- video movies use the Movie Rating System (MPAA) only.
I TV-G (General audience)
I TV-PG (Parental guidance suggested)
I TV-14 (Parents strongly cautioned)
I TV-MA (Mature audience only)
I TV-Y (All children)
I TV-Y7 (Children 7 years older)
Setting up Your Password
Set up blocking schemes to block specific channels, ratings, and external viewing sources. A password is required to gain access to this menu.
*
I Enter the password as requested.
I The TV is set up with the initial pass-
word “0-0-0-0”.




Choose any 4 digits for your new password. As soon as the 4 digits are entered, re-enter the same 4 digits on the Confirm.


Blocks any channels that you do not want to watch or that you do not want your children to watch.
I If a channel is locked, enter the pass-


Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.
I If Movie Rating, TV Rating- Children or TV Rating-General is locked, enter the password to unlocked it temporarily.
be available, PG-13, R, NC-17 and X will be blocked.


Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audi- ences in the TV Rating - sub menu, your children can view those programs.


Based on the ratings, blocks certain TV programs that you and your family do not want to view.


French is locked, enter the password to unlocked it temporarily.




This function is available only for digital channels. This function operates only when TV has received Region5 Rating data.
(On Screen Display) may differ slightly from what is shown in this manual.



TROUBLESHOOTING
The operation does not work normally.
I Check to see if there is any object between the product and the remote control
causing obstruction. Ensure you are pointing the remote control directly at the TV.
I Ensure that the batteries are installed with correct polarity (+ to +, - to -).
I Ensure that the correct remote operating mode is set: TV, VCR etc.
I Install new batteries.
*This feature is not available for all models.
I Is the sleep timer set?
I Check the power control settings. Power interrupted.
I TV will be automatically turned off, in case of no signal for 15 minutes.
The video does not work.
I Check whether the product is turned on.
I Try another channel. The problem may be with the broadcast.
I Is the power cord inserted into wall power outlet?
No picture &No sound
I Check your antenna direction and/or location.
I Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.
I This is normal, the image is muted during the product startup process. Please
contact your service center, if the picture has not appeared after five minutes.
I Adjust Color in menu option.
I Keep a sufficient distance between the product and the VCR.
No or poor color
I Try another channel. The problem may be with the broadcast.
I Are the video cables installed properly?
I Activate any function to restore the brightness of the picture.
I Check for local interference such as an electrical appliance or power tool.
I Station or cable product experiencing problems, tune to another station.
I Station signal is weak, reorient antenna to receive weaker station.
I Check for sources of possible interference.
I Check antenna (Change the direction of the antenna).
I Check HDMI cable over version 1.3.
No picture when connecting HDMI
The HDMI cables don’t support HDMI version 1.3, it cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.

The audio does not work.
I Press the VOL or VOLUME button.
I Sound muted? Press MUTE button.
Picture OK & No sound
I Try another channel. The problem may be with the broadcast.
I Are the audio cables installed properly?
No output from one
I Adjust Balance in menu option.
I A change in ambient humidity or temperature may result in an unusual noise
when the product is turned on or off and does not indicate a fault with the product.
I Check HDMI cable over version 1.3.
No sound when connecting
I Check USB cable over version 2.0.
I Use normal MP3 file. *This feature is not available for all models.
There is a problem in PC mode. (Only PC mode applied)
I Adjust resolution, horizontal frequency, or vertical frequency.
The signal is out of range
I Check the input source.
Vertical bar or stripe on
background & Horizontal Noise &
I Work the Auto configure or adjust clock, phase, or H/V position. (Option)
I Check the signal cable.
Screen color is unstable
I Reinstall the PC video card.

MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
I To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
I Please be sure not to use a wet cloth.
G If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.

32LH40 (32LH40-UA) 32LH41 (32LH41-UE) 37LH40 (37LH40-UA) 37LH41 (37LH41-UE) 42LH40 (42LH40-UA) 42LH41 (42LH41-UE)
31.6 x 23.0 x 8.8 inches 804.4 x 586.3 x 223.8 mm
36.4 x 26.2 x 11.6 inches 924.7 x 666.7 x 296.2 mm
40.7 x 28.3 x 11.6 inches 1036.0 x 721.3 x 296.2 mm
Dimensions (Width x Height x Depth)
31.6 x 20.8 x 3.1 inches 804.4 x 529.2 x 81.0 mm
36.4 x 23.6 x 3.5 inches 924.7 x 599.9 x 89.6 mm
40.7 x 25.8 x 3.5 inches 1036.0 x 655.4 x 89.8 mm
With stand Without stand
27.9 lbs / 12.7 kg 25.3 lbs / 11.5 kg
34.8 lbs / 15.8 kg 30.8 lbs / 14.0 kg
41.6 lbs / 18.9 kg 37.6 lbs / 17.1 kg
MODELS 47LH40 (47LH40-UA) 47LH41 (47LH41-UE)
45.4 x 31.1 x 13.2 inches 1153.2 x 791.5 x 337.4 mm
52.7 x 35.4 x 16.6 inches 1339.0 x 901.0 x 423.0 mm
Dimensions (Width x Height x Depth)
45.4 x 28.3 x 3.9 inches 1153.2 x 719.0 x 99.8 mm
52.7 x 32.6 x 4.2 inches 1339.0 x 828.6 x 108.6 mm
With stand Without stand
48.9 lbs / 22.2 kg 43.2 lbs / 19.6 kg
79.3 lbs / 36.0 kg 71.6 lbs / 32.5 kg
42CL40 (42CL40-UA)
47CL40 (47CL40-UA)
32.0 x 23.5 x 9.1 inches 813.8 x 598.8 x 231.9 mm
40.7 x 28.9 x 11.5 inches 1034.0 x 735.0 x 294.0 mm
45.5 x 32.0 x 13.5 inches 1156.2 x 813.1 x 342.9 mm
Dimensions (Width x Height x Depth)
32.0 x 21.2 x 3.1 inches 813.8 x 540.4 x 78.9 mm
40.7 x 26.1 x 3.6 inches 1034.0 x 663.0 x 92.0 mm
45.5 x 29.1 x 4.0 inches 1156.2 x 739.2 x 103.0 mm
With stand Without stand
26.8 lbs / 12.2 kg 23.3 lbs / 10.6 kg
45.4 lbs / 20.6 kg 39.6 lbs / 18.0 kg
55.9 lbs / 25.4 kg 45.8 lbs / 20.8 kg
Power requirement Television System Program Coverage External Antenna Impedance
AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
Operating Temperature Operating Humidity
32 ~ 104°F (0 ~ 40°C) Less than 80%
Storage Temperature Storage Humidity
I The specifications shown above may be changed without prior notice for quality improvement.

42LH55 (42LH55-UA)
MODELS
Dimensions (Width x Height x Depth)
37.0 x 26.1 x 11.6 inches 940.8 x 665.2 x 296.2 mm
41.4 x 28.3 x 11.6 inches 1052.2 x 719.1 x 296.2 mm
37.0 x 23.7 x 3.5 inches 940.8 x 603.5 x 90.6 mm
41.5 x 25.8 x 3.5 inches 1052.2 x 657.3 x 90.8 mm
With stand Without stand
35.9 lbs / 16.3 kg 31.9 lbs / 14.5 kg
41.8 lbs / 19.0 kg 37.9 lbs / 17.2 kg
55LH55 (55LH55-UA)
Dimensions (Width x Height x Depth)
46.1 x 31.0 x 13.2 inches 1173.4 x 789.7 x 337.4 mm
53.4 x 35.4 x 16.6 inches 1357.0 x 901.0 x 423.0 mm
46.1 x 28.4 x 3.9 inches 1173.4 x 723.4 x 100.8 mm
53.4 x 32.8 x 4.3 inches 1357.0 x 835.4 x 109.6 mm
With stand Without stand
51.5 lbs / 23.4 kg 45.8 lbs / 20.8 kg
80.2 lbs / 36.4 kg 72.5 lbs / 32.9 kg
Power requirement Television System Program Coverage External Antenna Impedance
AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
Operating Temperature Operating Humidity
32 ~ 104°F (0 ~ 40°C) Less than 80%
Storage Temperature Storage Humidity
I The specifications shown above may be changed without prior notice for quality improvement.

Code Function Note (Hexa)
Code Function Note (Hexa)
08 POWER Remote control Button (Power On/Off)
D6 TV Discrete IR Code
45 Q.MENU Remote control Button
43 MENU Remote control Button
C4 POWER ON Discrete IR Code
0B INPUT Remote control Button
10-19 Number Key 0-9 Remote control Button
C5 POWER OFF Discrete IR Code
4C - (Dash)/LIST Remote control Button
1A FLASHBK Remote control Button
5A AV1 Discrete IR Code
09 MUTE Remote control Button
02 VOL + Remote control Button
D0 AV2 Discrete IR Code
03 VOL - Remote control Button
00 CH Remote control Button
BF COMPONENT1 Discrete IR Code
01 CH Remote control Button
1E FAV/MARK Remote control Button
D4 COMPONENT2 Discrete IR Code
40 Remote control Button
41 Remote control Button
D5 RGB-PC Discrete IR Code
07 Remote control Button
06 Remote control Button
CE HDMI1 Discrete IR Code
44 ENTER Remote control Button
28 RETURN Remote control Button
CC HDMI2 Discrete IR Code
79 RATIO Remote control Button
0E SLEEP Remote control Button
E9 HDMI3 Discrete IR Code
95 ENERGY SAVING Remote control Button
7E SIMPLINK Remote control Button
DA HDMI4 Discrete IR Code
AA INFO Remote control Button
30 AV MODE Remote control Button
76 Ratio 4:3 Discrete IR Code
72 RED Remote control Button
(Only 4:3 Mode)
71 GREEN (A) Remote control Button
77 Ratio 16:9 Discrete IR Code
63 YELLOW (G) Remote control Button
(Only 16:9 Mode)
61 BLUE (l l) Remote control Button
AF Ratio Zoom Discrete IR Code
8F FF Remote control Button
8E GG Remote control Button

EXTERNAL CONTROL THROUGH RS-232C
The RS-232C port allows you connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the TV’s functions externally.
I Note: RS-232C on this unit is intended to be used with third party RS-232C control hardware and software.
The instructions below are provided to help with programming software or to test functionality using telenet software.

Communication Parameters

I Use a crossed (reverse) cable.

G This product has command echo back in the


RXD 2 3 TXD TXD 3 2 RXD GND 5 5 GND DTR 4 6 DSR DSR 6 4 DTR RTS 7 8 CTS CTS 8 7 RTS
RXD 2 3 TXD TXD 3 2 RXD GND 5 5 GND DTR 4 6 DTR DSR 6 4 DSR RTS 7 7 RTS CTS 8 8 CTS
Use this function to specify a TV ID number. Refer to ‘Real Data Mapping’.
Choose the desired TV ID number. The adjustment range of Set ID is 1~99.

Command Reference List
DATA (Hexadecimal) COMMAND1 COMMAND2 DATA (Hexadecimal)
01. Power k a 00 ~ 01 02. Input Select x b (G p.119) 03. Aspect Ratio k c (G p.119) 04. Screen Mute k d (G p.119) 05. Volume Mute k e 00 ~ 01 06. Volume Control k f 00 ~ 64 07. Contrast k g 00 ~ 64 08. Brightness k h 00 ~ 64 09. Color k i 00 ~ 64 10. Tint k j 00 ~ 64 11. Sharpness k k 00 ~ 64 12. OSD Select k l 00 ~ 01 13. Remote Control Lock Mode
00 ~ 01 k m

physical major major low minor high minor low attribute program high program low m a
* In this model, TV will not send the status during the standby mode. * Data Format [Command 2] : Use as command. [Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’. [DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’. [OK] : Use the large character.
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the set.(j, k, m or x) [Command 2] : Second command to control the set. [Set ID] : You can adjust the set ID to choose desired TV ID
number in Setup menu. Adjustment range is 1~ 99. When selecting Set ID ‘0’, every connected the TV is controlled. Set ID is indicated as decimal (1~ 99) on menu and as Hexa decimal (0x0~ 0x63) on transmission /receiving protocol. [DATA] : To transmit the command data.
[Command2][ ][Set ID][ ][NG][Data][x]
The TV transmits ACK (acknowledgement) based on this for- mat when receiving abnormal data from non-viable functions or communication errors.
Transmit the ‘FF’ data to read status of command. [Cr] : Carriage Return
ASCII code ‘0x0D’ [ ] : ASCII code ‘space (0x20)’ * In this model, TV will not send the status during the standby mode.
Data3: Wait more time * In this model, TV will not send the status during the standby mode. * Data Format [Command 2] : Use as command. [Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’. [DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’. [NG] : Use the large character
[Command2][ ][Set ID][ ][OK][Data][x]
The TV transmits ACK (acknowledgement) based on this for- mat when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
Transmission · Error Acknowledgement · OK Acknowledgement


You can also adjust mute using the MUTE button on remote control.
* In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function.
* Note: In this model, TV will send the Acknowledge after power on processing completion.
You can also adjust volume with the volume buttons on remote control.
There might be a time delay between command and acknowledge.
You can also adjust contrast in the PICTURE menu.
You can also adjust brightness in the PICTURE menu.
You can also adjust color in the PICTURE menu.
* In case of Video-out Mute on only, TV will display On Screen Display (OSD). But, in case of screen mute on, TV will not display On Screen Display (OSD).
You can also adjust tint in the PICTURE menu.

To adjust screen sharpness.
To adjust color temperature.
You can also adjust sharpness in the PICTURE menu.
You can also adjust color temperature in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Transmission [k][u][ ][Set ID][ ][Data][Cr]
*Refer to ‘Real data mapping’.
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]
To control the energy saving function.
To select OSD (On Screen Display) on/off.
Transmission [ j ][q][ ][Set ID][ ][Data][Cr]
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]
To lock the remote control and the front panel controls on the set.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
If you’re not using the remote control and front panel controls on the TV, use this mode. When main power is on/off, remote control lock is released.
To adjust picture position and minimize image shaking automatically. Auto configuration only works in RGB-PC mode.
Transmission [ j ][u][ ][Set ID][ ][Data][Cr]
If Key Lock is on in the standby mode, TV will not turn on by POWER button of remote control and on the TV.
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
To adjust treble.
You can also adjust treble in the AUDIO menu.
To tune channel to following physical/major/minor number.
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
*Refer to ‘Real data mapping’.
Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the number that the channel should be mapped to, and the Minor is the sub-channel. Since the ATSC tuner automatically maps the channel to the Major number, the Physical number is not required when sending a command.
Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]
To adjust bass.
You can also adjust bass in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
*Refer to ‘Real data mapping’.
Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]
Two bytes are available for the Major and Minor, nor- mally only the second byte is used.
To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Not needed for NTSC.
*Refer to ‘Real data mapping’.
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]

Data5:
Two/One Part Channel 7
Using Physical Channel 6
NTSC Air NTSC Cable
ATSC Air ATSC Cable_std ATSC Cable_hrc
ATSC Cable_irc ATSC cable_auto
... Reserved
The table above lists the binary code which must be converted to Hexadecimal before sending. For example: The binary code to tune the sub source to an NTSC cable channel is “1000 0001”, which translates to “81” in Hex.
To add and delete the channels.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
* 7th bit : For which source do you want to change the channel.
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
* 6th bit: Use a two part or one part channel. Most cases just use 0 since it’s ignored when using NTSC.
To send IR remote control code.
* 5th bit: Use 0 with NTSC since it can only use the phys- ical channel number. Normally use 1 for ATSC since most times it doesn’t matter what the physical number is.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
See page 115.
* 4th bit: Set to 0.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
* 3-0 bits: Choose signal type.
When TV is in the standby mode, TV will turn on by POWER button of remote control only.
* Tune Command Examples:
Data 00 = Physical of 35 = 23
To adjust screen backlight.
Data 01 & 02 = No Major = 00 00
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data 03 & 04 = No Minor = 00 00
Data Min:00 ~ Max:64 (*transmit by Hexadecimal code)
Data 05 = 0000 0001 in binary = 01
*Refer to ‘Real data mapping’.
Total = ma 00 23 00 01
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = 0010 0010 in binary = 22
Total = ma 00 00 00 1E 00 03 22
Acknowledgement[a][ ][Set ID][ ][OK][Data00][Data01] [Data02][Data03][Data04][x][a][ ][Set ID]

OPEN SOURCE LICENSE - This feature is not available for all models.
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all.
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software - to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other free software foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too.
0. This license applies to any program or other work which con- tains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work con- taining the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you".
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
Activities other than copying, distribution and modification are not covered by this license; they are outside its scope. The act of running the Program is not restricted, and the out- put from the program is covered only if its contents constitute a work based on the program (independent of having been made by running the program). Whether that is true depends on what the program does.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the soft- ware, and (2) offer you this license which gives you legal permis- sion to copy, distribute and/or modify the software.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
Also, for each author's protection and ours, we want to make cer- tain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making
a) You must cause the modified files to carry prominent
Preamble

b) You must cause any work that you distribute or publish,
c) Accompany it with the information you received as to the
that in whole or in part contains or is derived from the Program or any part there of, to be licensed as a whole at no charge to all third parties under the terms of this license. c) If the modified program normally reads commands interac-
offer to distribute corresponding source code. (This alter- native is allowed only for noncommercial distribution and only if you received the program in object code or exe- cutable form with such an offer, in accord with Subsection b above.)
tively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this license. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all mod- ules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this license, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the dis- tribution of the whole must be on the terms of this license, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
If distribution of executable or object code is made by offer- ing access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
Thus, it is not the intent of this section to claim rights or con- test your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the program.
In addition, mere aggregation of another work not based on the program with the Program (or with a work based on the program) on a volume of a storage or distribution medium does not bring the other work under the scope of this license.
5. You are not required to accept this license, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this license. Therefore, by modifying or distributing the program (or any work based on the program), you indicate your accep- tance of this license to do so, and all its terms and conditions for copying, distributing or modifying the program or works based on it.
readable source code, which must be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three
years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange; or,

7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the con- ditions of this license, they do not excuse you from the con- ditions of this license. If you cannot distribute so as to satis- fy simultaneously your obligations under this license and any other pertinent obligations, then as a consequence you may not distribute the program at all. For example, if a patent license would not permit royalty-free redistribution of the program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this license would be to refrain entirely from distribution of the program.
any later version published by the Free Software Foundation. If the program does not specify a version number of this license, you may choose any version ever published by the Free Software Foundation.
10.If you wish to incorporate parts of the program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copy- righted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of pro- moting the sharing and reuse of software generally.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
11.BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLD- ERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest valid- ity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution sys- tem, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRO- GRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUS- TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this license.
Each version is given a distinguishing version number. If the program specifies a version number of this license which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of

Also add information on how to contact you by electronic and paper mail.
How to apply these terms to your new programs
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
If you develop a new program, and you want it to be of the great- est possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free software, and you are welcome to redistribute it under certain conditions; type ‘show c’ for details.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effective- ly convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.
The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than ‘show w’ and ‘show c’; they could even be mouse-clicks or menu items-whatever suits your program.
one line to give the program's name and a brief idea of what it does. Copyright (C)
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the pro- gram, if necessary. Here is a sample; alter the names:
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the license, or (at your option) any later version.
Yoyodyne, Inc., hereby disclaims all copyright interest in the pro- gram ‘Gnomovision’ (which makes passes at compilers) written by James Hacker.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR- POSE. See the GNU General Public License for more details.
signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subrou- tine library, you may consider it more useful to permit linking pro- prietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this license.

GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is mod- ified by someone else and passed on, the recipients should know that what they have is not the original version, so that the origi- nal author's reputation will not be affected by problems that might be introduced by others.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, ver- sion 2, hence the version number 2.1.]
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company can- not effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software - to make sure the software is free for all its users.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to per- mit linking those libraries into non-free programs.
This license, the Lesser General Public License, applies to some specially designated software packages - typically libraries - of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think careful- ly about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free soft- ware (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.
We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software devel- opers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license pro- vides advantages in certain special circumstances.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.
Preamble

Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.
each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this license and to the absence of any warranty; and distribute a copy of this license along with the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
charge to all third parties under the terms of this license. d) If a facility in the modified Library refers to a function or a
table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.
The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.)
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any appli- cation-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the library, and can be reasonably considered independent and separate works in themselves, then this license, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the library, the dis- tribution of the whole must be on the terms of this license, whose permissions for other licenses extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or con- test your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the library.
“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it con- tains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this license; they are outside its scope. The act of running a program using the Library is not restrict- ed, and output from such a program is covered only if its con- tents constitute a work based on the library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the library does and what the program that uses the library does.
In addition, mere aggregation of another work not based on the library with the library (or with a work based on the library) on a volume of a storage or distribution medium does not bring the other work under the scope of this license.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the library into a program that is not a library.
the object file is unrestricted, regardless of whether it is legal- ly a derivative work. (Executable containing this object code plus portions of the library will still fall under Section 6.)
Otherwise, if the work is a derivative of the library, you may distribute the object code for the work under the terms of Section 6. Any executable containing that work also fall under Section 6, whether or not they are linked directly with the library itself.
4. You may copy and distribute the library (or a portion or deriv- ative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine- readable source code, which must be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.
You must give prominent notice with each copy of the work that the library is used in it and that the Library and its use are covered by this license. You must supply a copy of this license. If the work during execution displays copyright notices, you must include the copyright notice for the library among them, as well as a reference directing the user to the copy of this license. Also, you must do one of these things:
a) Accompany the work with the complete corresponding
machine-readable source code for the library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the library and then relink to produce a modified executable containing the modified library. (It is understood that the user who changes the contents of definitions files in the library will not necessarily be able to recompile the appli- cation to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the
However, linking a “work that uses the library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the library), rather than a “work that uses the library”. The executable is therefore cov- ered by this license. Section 6 states terms for distribution of such executable.
library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the exe- cutable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least
When a “work that uses the library” uses material from a head- er file that is part of the library, the object code for the work may be a derivative work of the library even though the source code is not. Whether this is true is especially significant if the work can be linked without the library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.
three years, to give the same user the materials specified in Subsection 6, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to
copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these
If such an object file uses only numerical parameters, data structure layouts and accessories, and small macros and small inline functions (ten lines or less in length), then the use of
materials or that you have already sent this user a copy.

For an executable, the required form of the "work that uses the library" must include any data and utility programs need- ed for reproducing the executable from it. However, as a spe- cial exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the exe- cutable.
of the rights granted herein. You are not responsible for enforcing compliance by third parties with this license.
11.If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the con- ditions of this license, they do not excuse you from the con- ditions of this license. If you cannot distribute so as to satis- fy simultaneously your obligations under this license and any other pertinent obligations, then as a consequence you may not distribute the library at all. For example, if a patent license would not permit royalty-free redistribution of the library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this license would be to refrain entirely from distribution of the library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest valid- ity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution sys- tem which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a license cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this license.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normal- ly accompany the operating system. Such a contradiction means you cannot use both them and the library together in an executable that you distribute.
a) Accompany the combined library with a copy of the same
work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the sections above. b) Give prominent notice with the combined library of the
fact that part of it is a work based on the library, and explaining where to find the accompanying uncombined form of the same work.
12.If the distribution and/or use of the library is restricted in cer- tain countries either by patents or by copyrighted interfaces, the original copyright holder who places the library under this license may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this license incorporates the limitation as if written in the body of this license.
9. You are not required to accept this license, since you have not signed it. However, nothing else grants you permission to mod- ify or distribute the library or its derivative works. These actions are prohibited by law if you do not accept this license. Therefore, by modifying or distributing the library (or any work based on the library), you indicate your acceptance of this license to do so, and all its terms and conditions for copying, distributing or modifying the library or works based on it.
13.The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the library specifies a version number of this license which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation.
10.Each time you redistribute the library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or mod- ify the library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise

If the library does not specify a license version number, you may choose any version ever published by the Free Software Foundation.
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.
14.If you wish to incorporate parts of the library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make excep- tions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
one line to give the library's name and a brief idea of what it does. Copyright (C)
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the license, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR- POSE. See the GNU Lesser General Public License for more details.
15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLD- ERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names:
16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUS- TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a library for tweaking knobs) written by James Random Hacker.
signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice
How to apply these terms to your new libraries
If you develop a new library, and you want it to be of the great- est possible use to the public, we recommend making it free soft- ware that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License).

Version 1.1
1.Definitions.
code which is described in the source code notice required by exhibit as original code, and which, at the time of its release under this license is not already covered code governed by this license.
1.0.1. “Commercial use” means distribution or otherwise making the covered code available to a third party.
1.1. “Contributor” means each entity that creates or con- tributes to the creation of modifications.
1.10.1.“Patent claims” means any patent claim(s), now owned or hereafter acquired, including without limitation, method, process, and apparatus claims, in any patent licensable by grantor.
1.2. “Contributor version” means the combination of the orig- inal code, prior modifications used by a contributor, and the modifications made by that particular contributor.
1.11. “Source code” means the preferred form of the covered code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an executable, or source code differential comparisons against either the original code or another well known, available covered code of the contributor's choice. The source code can be in a compressed or archival form, pro- vided the appropriate decompression or de-archiving soft- ware is widely available for no charge.
1.3. “Covered code” means the original code or modifications or the combination of the original code and modifications, in each case including portions thereof.
1.4. “Electronic distribution mechanism” means a mechanism generally accepted in the software development communi- ty for the electronic transfer of data.
1.5. “Executable” means covered code in any form other than source code.
1.12. “You” (or “Your”) means an individual or a legal entity exercising rights under, and complying with all of the terms of, this license or a future version of this license issued under section 6.1. For legal entities, “You” includes any entity which controls, is controlled by, or is under common control with You. For purposes of this definition, “control” means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) own- ership of more than fifty percent (50%) of the outstand- ing shares or beneficial ownership of such entity.
1.6. “Initial developer” means the individual or entity identified as the initial Developer in the Source Code notice required by exhibit A.
1.7. “Larger work” means a work which combines covered code or portions thereof with code not governed by the terms of this License.
1.8. “License” means this document.
1.8.1. “Licensable” means having the right to grant, to the maxi- mum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the rights conveyed herein.
2.1. The initial developer grant. The initial developer hereby grants You a world-wide, roy- alty-free, non-exclusive license, subject to third party intel- lectual property claims:
1.9. “Modifications” means any addition to or deletion from the substance or structure of either the original code or any previous modifications. When covered code is released as a series of files, a modification is:
a) under intellectual property rights (other than patent or
trademark) licensable by initial developer to use, repro- duce, modify, display, perform, sublicense and distrib- ute the original code (or portions thereof) with or with- out modifications, and/or as part of a larger work; and (b) under patents claims infringed by the making, using or
A. Any addition to or deletion from the contents of a file containing original code or previous modifications.
B. Any new file that contains any part of the original code or previous modifications.
selling of original code, to make, have made, use, prac- tice, sell, and offer for sale, and/or otherwise dispose of the original code (or portions there of).
1.10. “Original code” means source code of computer software

(c) the licenses granted in this section 2.1(a) and (b) are
You may not offer or impose any terms on any source code version that alters or restricts the applicable version of this license or the recipients' rights hereunder. However, you may include an additional document offering the additional rights described in section 3.5.
effective on the date Initial developer first distributes original code under the terms of this license. (d) Notwithstanding section 2.1(b) above, no patent
license is granted: 1) for code that You delete from the original Code; 2) separate from the original code; or 3) for infringements caused by: i) the modification of the original code or ii) the combination of the original code with other software or devices.
3.2. Availability of source code. Any modification which you create or to which you con- tribute must be made available in source code form under the terms of this license either on the same media as an executable version or via an accepted electronic distribu- tion mechanism to anyone to whom you made an exe- cutable version available; and if made available via elec- tronic distribution mechanism, must remain available for at least twelve (12) months after the date it initially became available, or at least six (6) months after a subsequent version of that particular modification has been made available to such recipients. You are responsible for ensur- ing that the source code version remains available even if the electronic distribution mechanism is maintained by a third party.
2.2. Contributor Grant. Subject to third party intellectual property claims, each contributor hereby grants You a world-wide, royalty-free, non-exclusive license
(a) under intellectual property rights (other than patent
or trademark) licensable by contributor, to use, reproduce, modify, display, perform, sublicense and distribute the modifications created by such contribu- tor (or portions thereof) either on an unmodified basis, with other modifications, as covered code and/or as part of a larger work; and (b) under patent claims infringed by the making, using, or
3.3. Description of modifications. You must cause all covered code to which you contribute to contain a file documenting the changes You made to create that covered code and the date of any change. You must include a prominent statement that the modification is derived, directly or indirectly, from original code provided by the initial developer and including the name of the initial developer in (a) the source code, and (b) in any notice in an executable version or related documentation in which you describe the origin or ownership of the covered code.
selling of modifications made by that contributor either alone and/or in combination with its contributor version (or portions of such combination), to make, use, sell, offer for sale, have made, and/or otherwise dispose of: 1) modifications made by that contributor (or portions thereof); and 2) the combination of mod- ifications made by that contributor with its contributor version (or portions of such combination). (c) the licenses granted in sections 2.2(a) and 2.2(b) are
effective on the date contributor first makes commer- cial use of the covered code. (d) Notwithstanding section 2.2(b) above, no patent
3.4. Intellectual property matters (a) Third party claims. If contributor has knowledge that a license under a third party's intellectual property rights is required to exercise the rights granted by such contributor under sections 2.1 or 2.2, contributor must include a text file with the source code distribution titled "LEGAL" which describes the claim and the party making the claim in sufficient detail that a recipient will know whom to contact. If contributor obtains such knowledge after the modification is made available as described in section 3.2, contributor shall promptly modi- fy the LEGAL file in all copies contributor makes available thereafter and shall take other steps (such as notifying appropriate mailing lists or newsgroups) reasonably calcu- lated to inform those who received the covered code that new knowledge has been obtained. (b) Contributor APIs. If contributor's modifications include an application programming interface and contributor has knowledge of patent licenses which are reasonably necessary to implement that API, contributor must also include this information in the LEGAL file.
license is granted: 1) for any code that contributor has deleted from the contributor version; 2) separate from the contributor version; 3) for infringements caused by: i) third party modifications of contributor version or ii) the combination of modifications made by that contributor with other software (except as part of the contributor version) or other devices; or 4) under patent claims infringed by covered code in the absence of modifications made by that contributor.
3.1. Application of license. The modifications which You create or to which you con- tribute are governed by the terms of this license, including without limitation section 2.2. The source code version of covered code may be distributed only under the terms of this license or a future version of this license released under section 6.1, and you must include a copy of this license with every copy of the source code you distribute.

(c) Representations. contributor represents that, except as disclosed pursuant to section 3.4(a) above, contributor believes that contributor's modifications are contributor's original creation(s) and/or contributor has sufficient rights to grant the rights conveyed by this license.
3.7. Larger works. You may create a larger work by combining covered code with other code not governed by the terms of this license and distribute the larger work as a single product. In such a case, you must make sure the requirements of this license are fulfilled for the covered code.
3.5. Required notices. You must duplicate the notice in exhibit A in each file of the source code. If it is not possible to put such notice in a particular source code file due to its structure, then You must include such notice in a location (such as a relevant directory) where a user would be likely to look for such a notice. If You created one or more modification(s), you may add your name as a contributor to the notice described in exhibit A. you must also duplicate this license in any documentation for the source code where You describe recipients' rights or ownership rights relating to covered code. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations to one or more recipients of covered code. However, you may do so only on your own behalf, and not on behalf of the Initial developer or any contributor. You must make it absolutely clear than any such warranty, support, indemni- ty or liability obligation is offered by you alone, and You hereby agree to indemnify the Initial developer and every contributor for any liability incurred by the Initial develop- er or such contributor as a result of warranty, support, indemnity or liability terms you offer.
4. Inability to comply due to statute or regulation. If it is impossible for you to comply with any of the terms of this license with respect to some or all of the covered code due to statute, judicial order, or regulation then you must: (a) comply with the terms of this license to the max- imum extent possible; and (b) describe the limitations and the code they affect. Such description must be included in the LEGAL file described in section 3.4 and must be included with all distributions of the source code. Except to the extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it.
6.1. New versions. Netscape communications corporation (“Netscape”) may publish revised and/or new versions of the license from time to time. Each version will be given a distinguishing version number.
3.6. Distribution of executable versions. You may distribute covered code in executable form only if the requirements of section 3.1-3.5 have been met for that covered code, and if you include a notice stating that the source code version of the covered code is available under the terms of this license, including a description of how and where you have fulfilled the obligations of section 3.2. The notice must be conspicuously included in any notice in an executable version, related documentation or collateral in which you describe recipients' rights relating to the covered code. You may distribute the executable version of covered code or ownership rights under a license of your choice, which may contain terms different from this license, provided that you are in compliance with the terms of this license and that the license for the exe- cutable version does not attempt to limit or alter the recip- ient's rights in the source code version from the rights set forth in this license. If you distribute the executable ver- sion under a different license you must make it absolutely clear that any terms which differ from this license are offered by you alone, not by the Initial developer or any contributor. You hereby agree to indemnify the initial developer and every contributor for any liability incurred by the initial developer or such contributor as a result of any such terms You offer.
6.2. Effect of new versions. Once covered code has been published under a particular version of the license, you may always continue to use it under the terms of that version. You may also choose to use such covered code under the terms of any subsequent version of the license published by netscape. No one other than netscape has the right to modify the terms applicable to covered code created under this license.
6.3. Derivative works. If You create or use a modified version of this license (which you may only do in order to apply it to code which is not already covered code governed by this license), You must (a) rename Your license so that the phrases "Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL", "NPL" or any confusingly similar phrase do not appear in your license (except to note that your license differs from this license) and (b) otherwise make it clear that Your version of the license contains terms which differ from the Mozilla Public license and netscape Public License. (Filling in the name of the initial developer, original code or con- tributor in the notice described in exhibit A shall not of themselves be deemed to be modifications of this license.)

7. DISCLAIMER OF WARRANTY. COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN “AS IS” BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE COV- ERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NON-INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFOR- MANCE OF THE COVERED CODE IS WITH YOU. SHOULD ANY COVERED CODE PROVE DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING, REPAIR OR CORRECTION. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER.
such participant under sections 2.1(b) and 2.2(b) are revoked effective as of the date you first made, used, sold, distributed, or had made, modifications made by that participant.
8.3. If you assert a patent infringement claim against partici- pant alleging that such participant's contributor version directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the initiation of patent infringement litigation, then the rea- sonable value of the licenses granted by such participant under sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license.
8.4. In the event of termination under sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by you or any distributor hereunder prior to termination shall survive termination.
8.1. This license and the rights granted hereunder will terminate automatically if you fail to comply with terms herein and fail to cure such breach within 30 days of becoming aware of the breach. All sublicenses to the covered code which are properly granted shall survive any termination of this license. Provisions which, by their nature, must remain in effect beyond the termination of this license shall survive.
9. LIMITATION OF LIABILITY. UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DIS- TRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUEN- TIAL DAMAGES OF ANY CHARACTER INCLUDING, WITH- OUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNC- TION, OR ANY AND ALL OTHER COMMERCIAL DAM- AGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAM- AGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULT- ING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM- AGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU.
8.2. If you initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions) against ini- tial developer or a contributor (the initial developer or contributor against whom you file such action is referred to as “Participant”) alleging that:
(a) such participant's contributor version directly or indi-
rectly infringes any patent, then any and all rights granted by such participant to you under sections 2.1 and/or 2.2 of this license shall, upon 60 days notice from Participant terminate prospectively, unless if within 60 days after receipt of notice you either: (i) agree in writing to pay participant a mutually agreeable reasonable royalty for your past and future use of modifications made by such participant, or (ii) withdraw your litigation claim with respect to the contributor version against such participant. If within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed upon in writing by the parties or the litigation claim is not withdrawn, the rights granted by partici- pant to you under sections 2.1 and/or 2.2 automati- cally terminate at the expiration of the 60 day notice period specified above. (b) any software, hardware, or device, other than such par-
ticipant's contributor Version, directly or indirectly infringes any patent, then any rights granted to You by

11. MISCELLANEOUS. This license represents the complete agreement concerning subject matter hereof. If any provision of this license is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This License shall be governed by California law provisions (except to the extent applicable law, if any, provides oth- erwise), excluding its conflict-of-law provisions. With respect to disputes in which at least one party is a citizen of, or an entity chartered or registered to do business in the united states of america, any litigation relating to this License shall be subject to the jurisdiction of the federal courts of the northern district of california, with venue lying in santa clara county, california, with the losing party responsible for costs, including without limitation, court costs and reasonable attorneys' fees and expenses. The application of the united nations convention on contracts for the International sale of goods is expressly excluded. Any law or regulation which provides that the language of a contract shall be construed against the drafter shall not apply to this license.
EXHIBIT A -Mozilla Public License.
The contents of this file are subject to the Mozilla Public License Version 1.1 (the “license”); you may not use this file except in compliance with the License. You may obtain a copy of the license at http://www.mozilla.org/MPL/
Software distributed under the license is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See the license for the specific language governing rights and limitations under the License.
The Original Code is
The Initial Developer of the Original Code is Portions created by are Copyright (C) All Rights Reserved.
Contributor(s):
Alternatively, the contents of this file may be used under the terms of the license (the "[___] License"), in which case the provisions of [ ] license are applicable instead of those above. If you wish to allow use of your version of this file only under the terms of the [ ] license and not to allow others to use your version of this file under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other provisions required by the [___] license. If you do not delete the provisions above, a recipient may use your version of this file under either the MPL or the [___] license."


Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.