

North/Latin America http://aic.lgservice.com Europe/Africa http://eic.lgservice.com Asia/Oceania http://biz.lgservice.com
LED LCD TV SERVICE MANUAL
CHASSIS : LD21C MODEL : 32LS3450/345S/345T
32LS341C/348C MODEL : 32LS341C/3450/345S/345T/348C-ZA



CONTENTS .............................................................................................. 2
SAFETY PRECAUTIONS ......................................................................... 3
SERVICING PRECAUTIONS ................................................................... 4
SPECIFICATION ....................................................................................... 6
ADJUSTMENT INSTRUCTION .............................................................. 11
BLOCK DIAGRAM ................................................................................. 16
EXPLODED VIEW .................................................................................. 19
SCHEMATIC CIRCUIT DIAGRAM
- 2 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes


Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Exploded View. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks.
Do not use a line Isolation Transformer during this check. Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5 mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.
It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1 W), keep the resistor 10 mm away from PCB.
Keep wires away from high voltage or high temperature parts.

always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.
Leakage Current Cold Check(Antenna Cold Check) With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1 MΩ and 5.2 MΩ. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.
- 3 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or expo sure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as “anti-static” can generate electrical charges sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electri cally shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replace ment ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity suf ficient to damage an ES device.)
General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before;
ule or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or
other electrical connection. c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explo sion hazard. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Do not spray chemicals on or near this receiver or any of its assemblies. 4. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable non-abrasive applicator; 10 % (by volume) Acetone and 90 % (by volume) isopropyl alcohol (90 % - 99 % strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 5. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 6. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 7. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 8. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heat sink in this receiver.
General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintain tip temperature within the range or 500 °F to 600 °F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire- bristle (0.5 inch, or 1.25 cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature.
(500 °F to 600 °F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-
type solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuit board printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices Some semiconductor (solid-state) devices can be damaged eas ily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component dam age caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alter natively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent poten tial shock reasons prior to applying power to the unit under test.
(500 °F to 600 °F) b. First, hold the soldering iron tip and solder the strand against
the component lead until the solder melts. c. Quickly move the soldering iron tip to the junction of the
component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the compo nent lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or
splashed solder with a small wire-bristle brush.
- 4 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the cir cuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 and 6 above.
Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered.
Removal 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suction-type solder removal device (or with solder braid) before removing the IC. Replacement 1. Carefully insert the replacement IC in the circuit board. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas).
At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connec tions).
1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire.
"Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection.
At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involves the installation of a jumper wire on the component side of the circuit board.
Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heat sink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heat sink.
1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly con nected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.
Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as pos sible to diode body. 2. Bend the two remaining leads perpendicular y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.
Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top.
- 5 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement.
1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C 2) Relative Humidity: 65 % ± 10 % 3) Power Voltage : Standard input voltage (AC 100-240 V~, 50/60 Hz) * Standard Voltage of each products is marked by models. 4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM. 5) The receiver must be operated for about 5 minutes prior to the adjustment.
- 6 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

- 7 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes


5.2. RGB Input (PC) - LS35/LS34/CS46 series models are not supported.

- 8 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes


- 9 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

between computer, jig, and set.

(3)
and which must be followed, according to the plan which can be changed only on agreeing. (2) Power adjustment : Free Voltage. (3) Magnetic Field Condition: Nil. (4) Input signal Unit: Product Specification Standard. (5) Reserve after operation : Above 5 Minutes (Heat Run) Temperature : at 25 °C ± 5 °C Relative humidity : 65 ± 10 % Input voltage : 220 V, 60 Hz (6) Adjustment equipments: Color Analyzer(CA-210 or CA-110),
(5) Click "Auto" tab and set as below. (6) Click "Run". (7) After downloading, check "OK" message.
DDC Adjustment Jig, Service remote control. (7) Push the "IN STOP" key - For memory initialization.

(4)
(5)
(7)...........OK
channel information by itself. 3. After function inspection, Push “In-stop” key.
* USB DOWNLOAD (1) Put the USB Stick to the USB socket. (2) Automatically detecting update file in USB Stick.
- If your downloaded program version in USB Stick is Low,
it didn't work. But your downloaded version is High, USB data is automatically detecting. (3) Show the message "Copying files from memory". (4) Updating is starting.
* Boot file Download (1) Execute ISP program "Mstar ISP Utility" and then click
"Config" tab. (2) Set as below, and then click "Auto Detect" and check "OK"


message. If "Error" is displayed, check connection between computer, jig, and set. (3) Click "Read" tab, and then load download file(XXXX.bin)
(5) Updating Completed, The TV will restart automatically. (6) If your TV is turned on, check your updated version and

Tool option. (explain the Tool option, next stage) * If downloading version is more high than your TV have, TV can lost all channel data. In this case, you have to channel recover. if all channel data is cleared, you didn’t have a DTV/ ATV test on production line.
* After downloading, have to adjust Tool Option again. (1) Push "IN-START" key in service remote control. (2) Select "Tool Option 1" and push "OK" key. (3) Punch in the number. (Each model has their number)
- 10 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

3.3. EDID data (1) HD RGB EDID data (RGB input : only LD21B support)
- Enter Service Mode by pushing "ADJ" key, - Enter Internal ADC mode by pushing "►" key at "7. ADC
Calibration".
ADC Calibration
0. Tool Option1
ADC Comp 480i NG
1. Tool Option2
ADC Comp 1080p NG
2. Tool Option3
ADC RGB NG
3. Tool Option4
4. Tool Option 5
Start Reset
5. Country Group
6. Area Option
(2) HD HDMI EDID data
7. ADC Calibration ඖ
9. 10 Point WB
10. Test Pattern
11. EDID D/L
12. Sub B/C
13. Touch Sensitivity Setting
<Caution> Using "power on" key of the Adjustment remote
control, power on TV.
a. Product ID
cf) TV set’s model name in EDID data is below.
downloaded.
e. Checksum: Changeable by total EDID data.
EDID D/L
HDMI1
NG
1. Tool Option2
HDMI2
NG
2. Tool Option3
HDMI3
NG
3. Tool Option4
RGB
NG
4. Tool Option 5
Start Reset
5. Country Group
6. Area Option
7 . ADC Calibration
8. White Balance
f. Vendor Specific(HDMI)
9. 10 Point WB
11 . EDID D/L
ඖ
12. Sub B/C
13. Touch Sensitivity Setting
- 11 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

* Connecting picture of the measuring instrument (On Automatic control) Inside PATTERN is used when W/B is controlled. Connect to auto controller or push Adjustment R/C POWER ON → Enter the mode of White-Balance, the pattern will come out.
Not to push the INSTOP key after completion if the function inspection.
* Auto-control interface and directions (1) Adjust in the place where the influx of light like floodlight
around is blocked. (illumination is less than 10 lux). (2) Adhere closely the Color analyzer(CA210) to the module
less than 10 cm distance, keep it with the surface of the Module and Color analyzer's prove vertically.(80° ~ 100°). (3) Aging time
CA210 : CCFL/EEFL -> CH9, Test signal: Inner pattern(80IRE) LED -> CH14, Test signal: Inner pattern(80IRE) ▪ If it is executed W/B adjustment in 2~3 minutes H/run, it is
power supply) and heat-run over 5 minutes. - Using 'no signal' or 'POWER ONLY' or the others, check
the back light on.
RS-232C COMMAND [CMD ID DATA] Wb 00 00 White Balance Start Wb 00 ff White Balance End
Color Temperature : COOL, Medium, Warm. One of R Gain/G Gain/ B Gain should be kept on 0xC0, and adjust other two lower than C0.(When R/G/B Gain are all C0, it is the FULL Dynamic Range of Module)
- 12 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

Balance".
White Balance
5.2. HI-POT auto-check (1) Pallet moves in the station. (POWER CORD / AV CORD is
Cool
172 172 192 64 64 64 ON 100 To Set
tightly inserted) (2) Connect the AV JACK Tester. (3) Controller (GWS103-4) on. (4) HI-POT test (Auto)
- If Test is failed, Buzzer operates. - If Test is passed, GOOD Lamp on and move to next proc ess automatically.
* After you finished all adjustments, Press "In-start" key and compare Tool option and Area option value with its BOM, if it is correctly same then unplug the AC cable. If it is not same, then correct it same with BOM and unplug AC cable. For correct it to the model's module from factory Jig model. * Push the "IN STOP" key after completing the function inspection. And Mechanical Power Switch must be set “ON”.
- Touchable Metal : 3KV / min at 100mA - SIGNAL : 3KV / min at 100mA (2) TEST time: 1 second. (case : mass production ) (3) TEST POINT
- Touchable Metal => LIVE & NEUTRAL : Touchable Metal. - SIGNAL => LIVE & NEUTRAL : SIGNAL.
4.2. EYE-Q function check (1) Turn on TV. (2) Press EYE key of Adjustment remote control. (3) Cover the Eye Q II sensor on the front of the using your
hand and wait for 6 seconds. (4) Confirm that R/G/B value is lower than 10 of the "Raw
Data (Sensor data, Back light)". If after 6 seconds, R/G/B value is not lower than 10, replace Eye Q II sensor. (5) Remove your hand from the Eye Q II sensor and wait for 6



seconds. (6) Confirm that "ok" pop up. If change is not seen, replace
Eye Q II sensor.
CMD LENGTH ADH ADL DATA_1 . . . Data_n CS DELAY
CMD : A0h LENGTH : 85~94h (1~16 bytes) ADH : EEPROM Sub Address high (00~1F) ADL : EEPROM Sub Address low (00~FF) Data : Write data CS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_n Delay : 20ms
4.3. Outgoing condition Configuration ■ When pressing IN-STOP key by SVC remocon, Red LED
are blinked alternatively. And then automatically turn off. (Must not AC power OFF during blinking)
EEPROM WRITE A0h 84h+n n-bytes Write (n = 1~16)
* Description FOS Default write : write Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0, Phase Data write : Model Name and Serial Number write in EEPROM,.
- 13 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

6.3. Method & notice (1) Serial number D/L is using of scan equipment. (2) Setting of scan equipment operated by Manufacturing
Technology Group. (3) Serial number D/L must be conformed when it is produced in
production line, because serial number D/L is mandatory by D-book 4.0.
* Manual Download(Model Name and Serial Number) If the TV set is downloaded by OTA or Service man, sometimes model name or serial number is initialized.(Not always) There is impossible to download by bar code scan, so It need Manual download. 1) Press the "Instart" key of Adjustment remote control. 2) Go to the menu "6.Model Number D/L" like below photo. 3) Input the Factory model name or Serial number like photo.
EZ ADJUST
EDID D/L
0. Tool Option1
HDMI1
NG
1. Tool Option2
HDMI2
NG
2. Tool Option3
HDMI3
NG
3. Tool Option4
RGB
NG

Connection : PCBA (USB Port) → USB to Serial Adapter (UC-232A) → RS-232C cable → PC(RS-232C port) * Caution : LJ21* chassis support only UC-232A driver. (only use this one.)



- 14 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes

7.2 LAN Inspection 7.2.1. Equipment & Condition ▪ Each other connection to LAN Port of IP Hub and Jig

Address.

7.3. LAN PORT INSPECTION(PING TEST) Connect SET -> LAN port == PC -> LAN Port
7.3.1. Equipment setting (1) Play the LAN Port Test PROGRAM. (2) Input IP set up for an inspection to Test Program.
7.3.2. LAN PORT inspection (PING TEST) (1) Play the LAN Port Test Program. (2) Connect each other LAN Port Jack. (3) Play Test (F9) button and confirm OK Message. (4) Remove LAN cable.

- 15 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes


- 16 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes


- 17 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes


- 18 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes


Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
- 19 - LGE Internal Use Only Copyright © LG Electronics. Inc. All rights reserved. Only for training and service purposes


0.33uF 16V +12V/+15V
FROM LIPS & POWER B/D
CIS21J121
R611
OPT
0.1uF 16V R412
3.6uH IC401
0.01uF 50V
18 INV ON
21 12V 22 P.DIM1
23 GND/P.DIM2 24 Err OUT
R475
10 3.5V
12 3.5V
20 A.DIM
P404
6 GND
8 GND
14 GND
R608
12K
+5V_USB
[EP]LX
5 COMP
FW20020-24S
P401 SMAW200-H24S2
8 NC
7 SS
6 EN
NORMAL_EXPEPT_32
1 PWR ON
5 GND
7 GND
11 3.5V
13 GND
15 GND
SLIM_32~52
LED models need not use.
’ERROR_OUT’ is used for
lamp(CCFL/EEFL) models.
10K L401
THERMAL
1 PGND
2 VIN
3 AGND
4 FB
Vout=0.8*(1+R1/R2)
MMBT3906(NXP)
OPT
R610 33K
R2
Q402
OPT
R476
In other words,
MLB-201209-0120P-N2
OPT
0.1uF 16V
0.1uF 16V
R408
12K 1%
R406
4.7K
L404-*1
OPT
R609
MMBT3904(NXP)
0.1uF 16V
OPT
R1
CIS21J121
R416
56K
OPT
Q401
MLB-201209-0120P-N2
E
CIS21J121
L402-*1
0.1uF 16V
+3.5V_ST
B
R401
+3.5V_ST
10K OPT
10K
R462
10K
+12V/+15V
R461
RL_ON


LVDS for large inch
AUO_GND
AUO_GND/LGD_NC
R709
10K
OPT
PSU_T120_LGD PWM_DIM
PANEL_VCC
FHD
[51Pin LVDS Connector]
R706
RXA4+
RXA4-
RXA3+
RXA3-
RXACK-
RXA2+
RXA2-
RXA1+
RXA1-
RXA0+
RXB4+
RXB4-
RXB3+
RXB3-
RXBCK+
RXBCK-
RXB2+
RXB2-
RXB1+
RXB1-
RXB0+
RXB0-
(For FHD 60Hz)
FI-RE51S-HF-J-R1500
FHD
P703
1000pF 50V · 10uF 16V · 70-ohm


CLose to Saturn7M IC CLose to DDR3 CLose to DDR3 CLose to Saturn7M IC
0.1uF OS
0.01uF 50V
10K
R1235 56
R1236 56
A-MRASB
A-MCASB
A-MRESETB
A-MDQSL
A-MDQSLB
A-MDQSU
A-MDQSUB
A-MDQL1
A-MDQL2
A-MDQL3
A-MDQL4
A-MDQL5
A-MDQL6
A-MDQL7
A-MDQU0
A-MDQU1
A-MDQU2
A-MDQU3
A-MDQU4
A-MDQU5
A-MDQU6
A-MDQU7
A-MA0
A-MA1
A-MA2
A-MA3
A-MA4
A-MA5
A-MA6
A-MA7
A-MA8
A-MA9
A-MA10
A-MA11
A-MA12
A-MA13
A-MCKE
A-MODT
A-MWEB
A-MDML
A-MDMU
B-MVREFCA
A-MBA0
A-MBA1
A-MBA2
A-MVREFCA
A0 N3
A1 P7
A2 P3
A3 N2
A4 P8
A5 P2
A6 R8
A7 R2
A8 T8
A9 R3
A10/AP L7
A11 R7
A12/BC N7
A13 T3
NC_5 M7
BA0 M2
BA1 N8
BA2 M3
CK J7
CK K7
CKE K9
CS L2
ODT K1
RAS J3
CAS K3
WE L3
RESET T2
DQSL F3
DQSL G3
DQSU C7
DQSU B7
DML E7
DMU D3
DQL0 E3
DQL1 F7
DQL2 F2
DQL3 F8
DQL4 H3
DQL5 H8
DQL6 G2
DQL7 H7
DQU0 D7
DQU1 C3
DQU2 C8
DQU3 C2
DQU4 A7
DQU5 A2
DQU6 B8
DQU7 A3
H5TQ1G63DFR-H9C IC1201
EAN61828901
DDR_1333_HYNIX
0.1uF
1K 1%
1K 1%
VREFCA M8
VREFDQ H1
VDD_1 B2
VDD_2 D9
VDD_3 G7
VDD_4 K2
VDD_5 K8
VDD_6 N1
VDD_7 N9
VDD_8 R1
VDD_9 R9
VDDQ_1 A1
VDDQ_2 A8
VDDQ_3 C1
VDDQ_4 C9
VDDQ_5 D2
VDDQ_6 E9
VDDQ_7 F1
VDDQ_8 H2
VDDQ_9 H9
VSS_1 A9
VSS_2 B3
VSS_3 E1
VSS_4 G8
VSS_5 J2
VSS_6 J8
VSS_7 M1
VSS_8 M9
VSS_9 P1
VSS_10 P9
VSS_11 T1
VSS_12 T9
VSSQ_1 B1
VSSQ_2 B9
VSSQ_3 D1
VSSQ_4 D8
VSSQ_5 E2
VSSQ_6 E8
VSSQ_7 F9
VSSQ_8 G1
VSSQ_9 G9
R1204
R1205
NC_1 J1
NC_2 J9
NC_3 L1
NC_4 L9
NC_6 T7
ZQ L8
A-MVREFDQ
R1203
C1207 0.1uF
C1208 0.1uF
C1210 0.1uF
C1211 0.1uF
C1212 0.1uF
C1213 0.1uF
C1214 0.1uF
C1215 0.1uF
C1216 0.1uF OS
A-MVREFDQ
A-MA14
AVDD_DDR0
0.1uF
1K 1%
1K 1%
R1201
R1202


SPI_SDI
OS
0.1uF
R1405
OS
7 HOLD[IO3]
S_FLASH_MAIN_MACRONIX
5 SI/SIO0
S_FLASH_MAIN_WINBOND
5 DI[IO0]
MX25L8006EM2I-12G
7 HOLD#
6 SCLK
6 CLK
W25Q80BVSSIG
IC1401-*1
Serial Flash for SPI boot
1 CS#
2 SO/SIO1
3 WP#
4 GND
1 CS
2 DO[IO1]
3 %WP[IO2]
4 GND
R1404 4.7K
OPT
MMBT3904(NXP)
/SPI_CS
SPI_SDO
Q1401
+3.5V_ST
OPT
E
OPT
R1403
10K
B
OPT
R1401
/FLASH_WP


R1905 10K
0.1uF
R1907
0.1uF 16V
R1904
+3.3V_CI
10K
10K
0.1uF 16V
R1902 47
R1901 47
R1925 100
R1926 33
R1927 33
AR1903 33
BLM18PG121SN1D
CLOSE TO MSTAR
/CI_CD2
+3.3V_Normal
/CI_CD1
CI_TS_DATA[4]
CI_TS_DATA[5]
CI_TS_DATA[6]
CI_TS_DATA[7]
CI_MDI[0]
CI_MDI[1]
CI_MDI[2]
CI_MDI[3]
CI_MDI[4]
CI_MDI[5]
CI_MDI[6]
CI_MDI[7]
PCM_RST
/PCM_WAIT
REG
CI_TS_CLK
CI_TS_VAL
CI_TS_SYNC
CI_TS_DATA[0]
CI_TS_DATA[1]
CI_TS_DATA[2]
CI_TS_DATA[3]
CI_MISTRT
CI SLOT
CI_IORD
CI_IOWR
CI_MIVAL_ERR
CI_MCLKI
0.1uF
OPT


* H/W option : ETHERNET
ETHERNET
JK2100-*1
ETHERNET_UDE



IR/LED and control for on.y ’12 sub without IR-OUT.
KEY2
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.


so this has to be deleted in both main and ISDB sheet.
This was being applied to the only china demod,
TU_T/C/S2
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
5 +B1[3.3V]
7 +B2[1.8V]
12 +B3[3.3V]
TU2603
2 RESET
16 ERROR
18 VALID
1 NC_1
8 CVBS
9 NC_2
10 NC_3
11 NC_4
14 NC_5
17 SYNC
19 MCLK
3 SCL
4 SDA
6 SIF
15 GND
20 D0
21 D1
22 D2
23 D3
24 D4
25 D5
26 D6
27 D7
SHIELD
TU_T2/C
TDSS-G101D
9 IF_AGC
10 DIF[P]
11 DIF[N]
TU2602
2 RESET
5 +3.3V
7 +1.8V
TDSN-C201D
3 SCL
4 SDA
6 SIF
8 CVBS
TU2603-*1
5 +B1[3.3V]
7 +B2[1.8V]
12 +B3[3.3V]
13 +B4[1.23V]
1 NC
TU_T/C
2 RESET
8 CVBS
9 NC_1
10 NC_2
11 NC_3
14 NC_4
16 ERROR
17 SYNC
18 VALID
19 MCLK
SHIELD
3 SCL
4 SDA
6 SIF
15 GND
20 D0
21 D1
22 D2
23 D3
24 D4
25 D5
26 D7
27 D8
TU_CHINA
SHIELD


Ouput trace widths should be sized to conduct at least 2A
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
LNB
1uF 50V
LNB
0.01uF 50V
ZD1
LNB
(Option:LNB)
MBR230LSFT1G
LNB
D2703
C2700 0.22uF 25V
LNB
A_GND
LNB_OUT


NON_LIPS
POWER_DET
10K
R3400
10K
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.


11 NC_8
12 VCC_1
13 VSS_1
14 NC_9
15 NC_10
16 CLE
17 ALE
18 WE
19 WP
20 NC_11
21 NC_12
22 NC_13
23 NC_14
+3.3V_Normal
2 NC_2
3 NC_3
4 NC_4
5 NC_5
6 NC_6
7 RY/BY
8 RE
9 CE
R144 2.2K
HDCP EEPROM EEPROM
4 GND
48 NC_29
47 NC_28
46 NC_27
45 NC_26
44 I/O7
43 I/O6
42 I/O5
41 I/O4
40 NC_25
39 NC_24
38 NC_23
37 VDD_2
36 VSS_2
35 NC_22
34 NC_21
33 NC_20
32 I/O3
31 I/O2
30 I/O1
29 I/O0
28 NC_19
27 NC_18
26 NC_17
25 NC_16 24 NC_15
R160 1K R161 1K
NAND_FLASH_1G_NUMONYX
48 NC_29
47 NC_28
46 NC_27
45 NC_26
40 NC_25
39 NC_24
38 NC_23
37 VCC_2
36 VSS_2
35 NC_22
34 NC_21
33 NC_20
28 NC_19
27 NC_18
26 NC_17
25 NC_16 24 NC_15
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
44 I/O7
43 I/O6
42 I/O5
41 I/O4
32 I/O3
31 I/O2
30 I/O1
29 I/O0
EAN60762401
R141 1K
R140 1K
NAND_FLASH_1G_SS
K9F1G08U0D-SCB0
Addr:10101--
EAN61857001
I2C_SCL
I2C_SDA
IC102-*2
1 NC_1
2 NC_2
3 NC_3
4 NC_4
5 NC_5
6 NC_6
7 RB
8 R
9 E
10 NC_7
11 NC_8
12 VDD_1
13 VSS_1
14 NC_9
15 NC_10
17 AL
18 W
19 WP
20 NC_11
21 NC_12
22 NC_13
23 NC_14
+3.3V_Normal
2 NC_2
3 NC_3
4 NC_4
5 NC_5
6 NC_6
7 R/B
8 RE
9 CE
10 NC_7
11 NC_8
12 VCC_1
13 VSS_1
14 NC_9
15 NC_10
16 CLE
17 ALE
18 WE
19 WP
20 NC_11
21 NC_12
22 NC_13
23 NC_14
OS
R109 3.9K
0.1uF
PWM2
OS
0.1uF
R129 22
+3.3V_Normal
R107 1K
OPT
R108 1K
R106 1K
MMBT3904(NXP)
48 NC_29
47 NC_28
46 NC_27
45 NC_26
44 I/O7
43 I/O6
42 I/O5
41 I/O4
40 NC_25
39 NC_24
38 NC_23
37 VCC_2
36 VSS_2
35 NC_22
34 NC_21
33 NC_20
32 I/O3
31 I/O2
30 I/O1
29 I/O0
28 NC_19
27 NC_18
26 NC_17
25 NC_16 24 NC_15
OS
R156 10K A_DIM
R157 100
R127 4.7K
NAND FLASH MEMORY
OPT
R105
1K
/PF_CE1
PF_ALE
/PF_WE
+3.3V_Normal
NAND_FLASH_1G_HYNIX
*Option : HDCP_EEPROM
OPT
H27U1G8F2BTR-BC
EAN35669102
IC102-*1
6 SCL
5 SDA
/F_RB
/PF_OE
/PF_CE0
E
A_DIM
2.2uF
7 WP
OPT
R104
10K
B
3.3K
R102
4 VSS
OS
10 NC_7
11 NC_8
12 VCC_1
13 VSS_1
14 NC_9
15 NC_10
16 CLE
17 ALE
18 WE
19 WP
20 NC_11
21 NC_12
22 NC_13
23 NC_14
1 NC_1
2 NC_2
3 NC_3
4 NC_4
5 NC_5
6 NC_6
7 R/B
8 RE
9 CE
DIMMING
A_DIM
PWM_DIM
R113 4.7K
/PF_WP


DDCDA_CK/GPIO23 T4
HOTPLUGA/GPIO19 V5
HOTPLUGB/GPIO20 R5
DDCDC_DA/GPIO28 AE8
DDCDC_CK/GPIO27 AD8
HOTPLUGC/GPIO21 AC8
DDCDD_DA/GPIO30 R6
DDCDD_CK/GPIO29 U6
HOTPLUGD/GPIO22 P5
CEC/GPIO5 R4
RXACKP J2
RXACKN J3
RXCCKP AE9
RXCCKN AC9
RXDCKP F2
RXDCKN F3
HSYNC0 P2
VSYNC0 R3
SOGIN0 M1
HSYNC1 V2
VSYNC1 V3
SOGIN1 T3
HSYNC2 AA2
SOGIN2 W1
CVBSOUT0 Y6
CVBSOUT1 AA1
MODEL_OPT_0
MODEL_OPT_1
R204 100 OPT MODEL_OPT_2
MODEL_OPT_3
MODEL_OPT_4
MODEL_OPT_5
MODEL_OPT_6
MODEL_OPT_7
RXA0P K3
RXA0N J1
RXA1P K2
RXA1N K1
RXA2P L2
RXA2N L3
RXC0P AC10
RXC0N AD9
RXC1P AC11
RXC1N AD10
RXC2P AE11
RXC2N AD11
RXD0P G3
RXD0N F1
RXD1P G2
RXD1N G1
RXD2P H2
RXD2N H3
RIN0P N2
RIN0M P3
GIN0P N3
GIN0M N1
BIN0P M3
BIN0M M2
RIN1P U3
RIN1M U2
GIN1P T1
GIN1M T2
BIN1P R2
BIN1M R1
RIN2P Y2
RIN2M AA3
GIN2P W2
GIN2M Y3
BIN2P V1
BIN2M W3
CVBS0 AA8
CVBS1 Y4
CVBS2 W4
CVBS3 AA5
CVBS4 Y5
CVBS5 AA4
VCOM AB4
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.
C211 0.047uF
C212 0.047uF
C213 0.047uF
C214 0.047uF
C215 0.047uF
C216 0.047uF
C218 0.047uF
C219 0.047uF
C220 0.047uF
C221 0.047uF
C222 0.047uF
C223 0.047uF
C225 0.047uF
C226 0.047uF
C227 0.047uF
C233 0.047uF
+3.3V_Normal
FHD
R226 1K
R227 1K
Close to MSTAR
PHM_ON
PHM_OFF
R253 33
R254 68
R255 33 SC1_G+/COMP1_Y+
R256 68
R257 33
R258 68
R211 1K
R212 1K
R237 33
R238 68
R239 33
R240 68
R241 33
R242 68
R244 33
R245 33
R246 33
R252 68
DVB_T2
NON_DVB_T2
R208 1K
R209 1K
EPHY_RP
EPHY_RN
EPHY_TP
EPHY_TN
+2.5V_Normal
3D
R207 1K
NON_3D
OLED
NON_OLED
R4027 1K
R4029 1K
DVB_S
NON_DVB_S
R4028 1K
R4030 1K
+3.3V_Normal
NON_120HZ
R291 1K
R294 1K
PC_L_IN
PC_R_IN
HP_LOUT
HP_ROUT
R290 1K
OS(not use) / NonOS_Non_ErrorOut
SCART1_RGB/COMP1
COMP2(common AV)
R203 100 RF_SW_OPT
*Opt : EU_OPT
R202 100 BOOSTER_OPT
CK+_HDMI1
CK-_HDMI1
D0+_HDMI1
D0-_HDMI1
D1+_HDMI1
D1-_HDMI1
D2+_HDMI1
D2-_HDMI1
DDC_SDA_1
DDC_SCL_1
PM_MODEL_OPT_1
CK+_HDMI2
CK-_HDMI2
D0+_HDMI2
D0-_HDMI2
D1+_HDMI2
D1-_HDMI2
D2+_HDMI2
D2-_HDMI2
DDC_SDA_2
DDC_SCL_2
CEC_REMOTE_S7
DSUB_HSYNC
DSUB_VSYNC
DSUB_R+
DSUB_R-
DSUB_G+
DSUB_G-
DSUB_B+
DSUB_B-
DSUB_SOG
SC1_ID
SC1_FB
SC1_SOG_IN
TU_CVBS
SC1_CVBS_IN
COMP2_Y+/AV_CVBS_IN
DTV/MNT_VOUT
R201 100 OPT
R4031 100 OPT
R4032 100 OPT
R4040 100 OPT
R4039 100 OPT
COMP2_Y+/AV_CVBS_IN
CVBS In/OUT
HPD1
HPD2
DSUB_B+
DSUB_B-
DSUB_SOG
SPDIF_OUT
DSUB
MODEL OPTION
HDMI
IF_AGC_SEL
LNA2_CTL
RF_SWITCH_CTL
DSUB_HSYNC
DSUB_VSYNC
DSUB_R+
DSUB_R-
DSUB_G+
DSUB_G-



AP2191DSG
MLB-201209-0120P-N2
USB1_DIODES
L1451-*1
3AU04S-305-ZC-(LG)
USB_1_32LS3500
JK1450-*1
1 2 3 4 5
3AU04S-345-ZC-H-LG
USB (SIDE)


R2806
EU_OPT
R2802
EU_OPT
R2803
EU_OPT
R2804
470K
EU_OPT
R2805
+3.3V_Normal
0.1uF 16V
D2810
470K
R2831
+3.3V_Normal
R2832
10K
OPT
OPT
R2841
OPT
D2809
10K
D2818
R2837
10K
OPT
D2806
D2808
D2807
D2800
OPT
D2801
EU_OPT
D2802
OPT
D2803
OPT
D2804
OPT
D2805
OPT
OPT
OPT
OPT
R2826
470K
R2825
470K
R2823
R2824
R2822
D2815
D2814
OPT
D2816
OPT
OPT
D2813
OPT
D2812
OPT
D2817
OPT
Full Scart
5E [RD]O-SPRING_2
4E [RD]CONTACT_2
4C [RD]CONTACT_1
5C [RD]O-SPRING_1
5D [WH]O-SPRING
7C [RD]E-LUG-S
5B [BL]O-SPRING
7B [BL]E-LUG-S
4A [GN]CONTACT
5A [GN]O-SPRING
6E [RD]E-LUG
6A [GN]E-LUG
COMPONENT
1 AUDIO_R_OUT 2 AUDIO_R_IN 3 AUDIO_L_OUT 4 AUDIO_GND 5 B_GND 6 AUDIO_L_IN 7 B_OUT 8 ID 9 G_GND 10 D2B_IN 11 G_OUT 12 D2B_OUT 13 R_GND 14 RGB_GND 15 R_OUT 16 RGB_IO 17 SYNC_GND1 18 SYNC_GND2 19 SYNC_OUT 20 SYNC_IN 21 COM_GND 22 AV_DET
JK2803
PSC008-01
JK2801
EU_OPT
1000pF 50V · 1000pF 50V


+3.5V_ST P1000
GND
2 PM_RXD
3 GND
4 PM_TXD
PM_RXD
PM_TXD
RS-232C 4PIN
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.


RGB_DDC_SDA
MSTAR_DEBUG_4P 1
12505WS-04A00
P1
MSTART DEBUG_4PIN
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.



First of all, Check whether there is SVC Bulletin in GCSC System for these model.
Contents of LCD TV Standard Repair Process
3 Tuning fail, Picture broken/ Freezing 3, 4
9 Wrecked audio/discontinuation/noise 10
10 D. Function error Remote control & Local switch checking 11
11 External device recognition error 12
12 E. Noise Circuit noise, mechanical noise 13
13 F. Exterior error Exterior defect 14
No video/Normal audio 1
2 No video/No audio 2
4 Color error 5
light spot, external device color error 6
B. Power error No power 7
auto on/off 8
8 C. Audio error No audio/Normal video 9
5 Vertical/Horizontal bar, residual image,
7 Off when on, off while viewing, power
A. Video error

Continue to the next page
17 Exchange LED driver Board (PSU) A-3/5 55” : driver board Other : PSU
Exchange T-Con Board (1) A-1/5
16 Exchange T-Con Board (2) A-2/5
18 Exchange Module itself (1) A-4/5
19 Exchange Module itself (2) A-5/5
ADJ Key A10
ADJ Key A10
Check LCD back light with naked eye A1
2 LED driver B+ 24V measuring method A2
3 Check White Balance value A3
4 Power Board voltage measuring method A4
TUNER input signal strength checking method A5
7 LCD-TV Version checking method A6
LCD TV connection diagram A7
condition A8
LCD TV connection diagram A8
condition A8
10 Check Link Cable (LVDS) reconnection
13 Check Link Cable (LVDS) reconnection
11 Adjustment Test pattern -
14 Adjustment Test pattern -
A. Video error_Vertical/Horizontal bar,
Defected Type caused by T-Con/
A. Video error_ No video/Normal
6 A. Video error_ No video/Video
residual image, light spot
error
A. Video error_Color
Inverter/ Module
<Appendix>
lag/stop
audio

Board or module
2012. 01 .14
Replace T-con
First of all, Check whether all of cables between board is inserted properly or not.
Balance value before replacing the Main Board Replace Main Board Re-enter White Balance value
Established
Repair Power
Board or parts Check Power Board 24v output
Normal
End
date
voltage
N
voltage Y Replace Inverter
Check Power
12v,3.5v etc.
(Main B/D ↔ Power B/D, LVDS Cable,Speaker Cable,IR B/D Cable,,,)
or module
Board
No video/ Normal audio
symptom A. Video error
On with naked eye On Y
Repair Power
Board or parts
N
Normal
N
Normal audio Check Back Light
Always check & record S/W Version and White
audio Y
video/No audio
☞ A6 & A3
Normal
N
Move to No
Standard Repair Process
※ Precaution
No video

symptom 2012 . 01 .14
Established
N End
date
Check and
MAIN B/D
replace
A. Video error
No video/ No audio
Y
Board and repair
Replace Power
voltage?
Normal
parts
Board ( 3.5V,12V,20V
voltages of Power
Check various
or 24V…)
No Video/
No audio
Standard Repair Process

Revised date 3/14 LCD TV Error
Y
Main B/D
Normal
Picture?
N N
Replace
symptom 2012. 01 .14
Tuner soldering
Check
Established
date
N
N
S/W Upgrade
Bulletin?
Normal
Picture?
SVC
Y
Close
Y
Check whether other equipments have problem or not.
Picture broken/ Freezing
(By connecting RF Cable at other equipment)
A. Video error
( Menu → Set up → Support → Signal Test )
S/W Version
Check
- Signal strength (Normal : over 50%)
. By using Diagnostics menu on OSD
- Signal Quality (Normal: over 50%)
Contact with signal distributor
or broadcaster (Cable or Air)
. By using Digital signal level meter
Y
Normal
Picture?
Standard Repair Process
Check RF Signal level
Y
N
Check RF Cable
1. Reconnection 2. Install Booster
Connection
Normal
Signal?
Normal
Picture?
N
Close
Y

Main B/D
Revised date 4/14 LCD TV Error
symptom 2012. 01 .14
Check
Y N
S/W Upgrade
N
Established
Bulletin?
Normal
Picture?
date
Y
Close
SVC
Y
S/W Version
Signal? Check
Check whether other equipments have problem or not.
Check RF signal cable (DVB satellite signal or not)
(By connecting RF Cable at other equipment)
(match with installed ANT)
A. Video error
Change satellite setting
Y
→ Set-Top-Box, Different maker TV etc
N
Normal
setting?
Normal
Picture?
N
Y
Close
- Check Satellite connection
- Check LNB frequency.
Check satellite setting.
Standard Repair Process
Check RF Signal level
signal distributor
or broadcaster
Contact with
(Cable or Air)
Normal
N
Close

Replace module
Replace Main B/D
Replace Main B/D
symptom 2012. 01 .14
Y
N
Color
error?
End
Established
Y External device
Y External device
date
Request repair
for external
device/cable
/Cable
normal
N
N
/Cable
normal
Replace Main B/D Color
Check external
Y
device and
device and
external
error?
N
Check
A. Video error
cable
cable
Color error
☞ A8/ A9
and replace
(LVDS) and
Link Cable
※ Check
condition
contact
External Input/
Component
HDMI/DVI
error
RGB/
error
Y
N
Check error
Color
error?
color input
mode
Check color by input
Check Test pattern ☞ A10
-COMPONENT
Standard Repair Process
-External Input
- HDMI/DVI
- RGB

Main B/D Screen
Replace
N
Screen
normal?
Y
Main B/D Screen
Replace
Module
End
Revised date 6/14 LCD TV Error
Request repair for
external device
N
N
normal?
Y
normal?
Replace Main B/D
Y
2012. 01 .14
(Check normal operation of
External Input, Component,
Generator ,Set-top Box etc.
External Input, Component,
Generator ,Set-top Box etc.
connecting Jig, pattern
Connect other external
(Check normal operation of
RGB and HDMI/DVI by
connecting Jig, pattern
N
device and cable
Established
normal?
device and cable
date
Screen
Y
End
☞ A7 ☞ A8/ A9
replace Link
Check and
Vertical / Horizontal bar, residual image,
Cable Normal?
Component
light spot, external device color error
External
Input
error
RGB
error
HDMI/
DVI
Request repair
Y
A. Video error
Vertical/Horizontal bar, residual image, light spot
for external
N
device
External device screen error-Color error
Check screen
-External Input
Y Check external
condition by
-Component
- HDMI/DVI
connection
condition
input
- RGB
device
normal?
Screen
N
Replace
module
N Check
N Normal
S/W Upgrade
symptom
version
screen?
Y
Y
End
Check color condition by input
Check Test pattern
Standard Repair Process
Check S/W Version
-External Input
-Component
- HDMI/DVI
- RGB

Power
Revised date 7/14 LCD TV Error
B/D
Replace Main B/D
Y OK?
N
2012. 01 .14
Measure voltage of each output of Power B/D
voltage? Replace Main B/D
operation? Check Power
On ‘”High”
Established
date
Y Normal
Replace Power B/D
N Normal
Y
N
Replace Power
by pressing Power Key
voltage?
Y
Y Normal
N
On Remote control
B. Power error
DC Power on
B/D
No power
Check ST-BY 3.5V
On? Y
was inserted properly
※
N
Check Power cord
Power LED
symptom
Normal?
Close
N
Y
Standard Repair Process
. Stand-By: Red
Check

Revised date 8/14 LCD TV Error
Replace Power B/D
Abnormal "POWEROFF_ABNORMAL1" Power off by abnormal status except CPU trouble
"POWEROFF_UNKNOWN" Power off by unknown status except listed case
N
2012. 01 .14
Status Power off List Explanation
Replace Main B/D Normal
"POWEROFF_REMOTEKEY" Power off by REMOTE CONTROL
"POWEROFF_RESREC" Power off by Reserved Record
"POWEROFF_RECEND" Power off by End of Recording
"POWEROFF_SLEEPTIMER" Power off by SLEEP TIMER
"POWEROFF_SWDOWN" Power off by S/W Download
"POWEROFF_CPUABNORMAL" Power off by CPU Abnormal
Replace Main B/D CPU
"POWEROFF_INSTOP" Power off by INSTOP KEY
"POWEROFF_OFFTIMER" Power off by OFF TIMER
"POWEROFF_AUTOOFF" Power off by AUTO OFF
"POWEROFF_ONTIMER" Power off by ON TIMER
"POWEROFF_RS232C" Power off by RS232C
Established
Replace Power B/D
date
Y
voltage?
N
Abnormal
Abnormal
Off when on, off while viewing, power auto on/off
(If Power Off mode
Check and fix exterior
Check Power B/D
is not displayed)
of Power B/D Part
Check Power Off
voltage
B. Power error
※ Caution
Normal
Mode
* Please refer to the all cases which can be displayed on power off mode.
Fix A/C cord & Outlet
and check each 3
Y
phase out
symptom
Standard Repair Process
Check for all 3phase
Check A/C cord
Check outlet
power out

2012. 01 .14
Replace MAIN Board End
Replace Power Board and repair parts
Established
date
Y
Normal
voltage
N
N
Replace Speaker
Disconnection
Check audio B+
Y
24V of Power Board
No audio/ Normal video
C. Audio error
☞ A15 ☞ A16
disconnection
Speaker off Off N
Cancel OFF
Speaker
Y
Check
Check user
menu >
symptom
Standard Repair Process
Screen normal
No audio

Revised date 10/14 LCD TV Error
→abnormal audio/discontinuation/noise is same after “Check input signal” compared to No audio
B+ Voltage (24V)
Y
2012. 01 .14
Check audio
voltage?
Replace Power B/D
Normal
Check and fix external device
N
N
Normal
audio?
Y
Established
date
Check and replace
Replace Main B/D N
Connect and check
speaker and
connector
other external
device
Wrecked audio/ discontinuation/noise
Wrecked audio/
Discontinuation/
Wrecked audio/
Discontinuation/
Wrecked audio/
Discontinuation/
for External Input
Wrecked audio/
Discontinuation/
Noise only
for D-TV
Noise only
for Analog
Noise only
Noise for
all audio
C. Audio error
Request repair to external
(When RF signal is not
cable/ANT provider
External Input
Check and fix
external device
(In case of
signal error)
received)
Y
symptom
normal?
Signal
Standard Repair Process
-External Input
Check input
signal
signal
-RF

Main B/D
Y ☞ A17
Repair/Replace
Revised date 11/14 LCD TV Error
Output signal Normal
Signal?
N
IR B/D
symptom 2012. 01 .14
Check IR
(Power B/D don’t have problem)
Check 3.5v on Power B/D
Replace Power B/D or
Y
Replace Main B/D
Established
date
Voltage?
Normal
N
3.5V On Main B/D
Check B+
Remote control & Local switch checking
D. Function error
N
operating?
Normal
Y
Close
1. Remote control(R/C) operating error
Cable connection
Connector solder
Check & Repair
Close
Check & Replace
Baterry of R/C
Replace R/C
operating?
Normal
N
Y
operating?
Operation Normal
N
Standard Repair Process
Check R/C Operating
Explain the customer
cause is interference
When turn off light
from light in room.
Check R/C itself
in room

2012. 01 .14
Replace Main B/D
Replace Main B/D Fix in
Established
date
External Input and
Recognition error
Recognition error
Component
RGB,HDMI/
DVI, Optical
External device recognition error
N
information?
with technical
D. Function error
Technical
accordance
information
Y
Check technical
- Fix information
- S/W Version
information
external device/cable
Y
Check and fix
Signal
input?
N
symptom
Standard Repair Process
Check
signal
input

※ When the nose is severe, replace the module
then proceed as shown in the solution manual
2012. 01 .14
(For models with fix information, upgrade the
cabinet, refer to the KMS fix information and
※ If there is a “Tak Tak” noise from the
(For models without any fix information,
S/W or provide the description)
Established
provide the description)
date
Replace PSU (with LED driver)
Replace LED driver
Circuit noise, mechanical noise
OR
E. Noise
OR
description. When the customer does not
※ Describe the basis of the description
in “Part related to nose” in the Owner’s
phenomenon, and apply the 1st level
agree, apply the process by stage.
※ Mechanical noise is a natural
location of
of noise
Check
noise
Mechanical
nose type Circuit
noise
symptom
Manual.
Identify

2012. 01 .14
Established
date
Replace remote controller Remote
F. Exterior defect
Replace module Zoom part with
damage Replace cabinet
dent Replace stand
Exterior defect
controller
exterior damage Module
damage
Cabinet
damage
Stand
symptom
Standard Repair Process
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.