
PLASMA TV MODELS
32LG30 37LG50 37LG30 42LG50 42LG30 47LG50 52LG50
42PG25 50PG25
50PG60 60PG60
32LG60 32LG70 37LG60 42LG70 42LG60 47LG70 47LG60 52LG70 52LG60
Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA).
An extended owner’s manual that contains information on the advanced features of these LG TV sets is located on the CD-ROM provided in an electronic version. To read these files, you will need to use personal computer (PC) equipped with a CD-ROM drive.
As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
www.lgusa.com
Printed in Korea

WARNING / CAUTION
To prevent fire or shock hazards, do not expose this product to rain or moisture.
DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO
Class B digital device This equipment has been tested and found to com- ply with the limits for a Class B digital device, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio fre- quency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi- sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and main- tenance (servicing) instructions in the literature accompanying the appliance.
and receiver. - Connect the equipment to an outlet on a circuit
different from that to which the receiver is con- nected. - Consult the dealer or an experienced radio/TV
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding sys- tem of the building, as close to the point of the cable entry as practical.
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product

IMPORTANT SAFETY INSTRUCTIONS
Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction:
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Do not use this apparatus near water.
Clean only with dry cloth.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Only use attachments/accessories specified by the manufacturer.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.
Unplug this apparatus when unused for long periods of time.
When mounting a TV it on the wall, make sure not to install TV by hanging power and signal cables on the back of the TV.

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Outdoor use marking : WARNING - To reduce the risk of fire or elec- tric shock, do not expose this appliance to rain or moisture.
Wet Location Marking : Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on or over apparatus.
Never touch this apparatus or antenna during a thunder or lighting storm.
Do not allow a impact shock or any objects to fall into the product, and do not drop onto the screen with something.
GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.
CAUTION concerning the Power Cord : Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates dam- age or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable.
I If the TV feels cold to the touch, there may be a
small “flicker” when it is turned on. This is normal, there is nothing wrong with TV.
I Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance.
I Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.
On Disposal The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.
Power Supply · Short-circuit · Breaker


Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the product. The accessories included may differ from the images below. For further information, see the the Owner's Manual files supplied CD-ROM.
Q. MENU MENU
STB
POWER
DVD
ENTER
INPUT
VCR
AV MODE RETURN
VOL CH
FAV
MUTE
P A G E
FLASHBK
1.5V 1.5V
Copyright© 2007 LGE, All Rights Reserved.
Owner’s Manual Power Cord Remote Control,
CD Manual (Refer to p.5)
* Wipe spots on the exterior only with the polishing cloth.
When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance.
* Do not wipe roughly when removing stain. Please be cautions of that excessive pressure may cause scratch or discoloration.
Polishing Cloth (This feature is not available
for all models.)
D-sub 15 pin Cable
For Plasma TV models
Bolts for stand assembly
(Refer to P.12)
(Refer to P.18)
For LCD TV models
32/42LG70)
Bolts for stand assembly
(Refer to P.18) Screw for stand fixing
(Refer to P.12)
(Refer to P.16)
(Only 32/37LG60) (Only 42LG60)
Bolts for stand assembly
(Refer to P.18)
(Refer to P.13)

I Image shown may differ from your TV.
I NOTE: If your TV has a protection tape attached, remove the tape.
And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it).
CH VOL MENU INPUT ENTER
Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on.
VOLUME (-, +) Buttons
CHANNEL (E,D)Buttons
CH
CHANNEL ( , ) Buttons
VOL
VOLUME (+, -) Buttons
ENTER
Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on. (Can be adjusted using Power Indicator in the OPTION menu.)
MENU
MENU
INPUT
INPUT
32/37/42/47/52LG60
CHANNEL ( , ) Buttons
VOLUME (+, -) Buttons
POWER Button Remote Control Sensor Power/Standby Indicator Illuminates red in standby mode. Illuminates white when the TV is switched on. (Can be adjusted using Power Indicator in the OPTION menu.)
MENU
INPUT


L/MONO R AUDIO VIDEO USB IN HDMI IN 4
L/MONO R AUDIO VIDEO HDMI IN 3 USB IN

ANTENNA/ CABLE IN
L/MONO R AUDIO VIDEO HDMI IN 4 USB IN
OPTICAL COAXIAL DIGITAL AUDIO OUT
HDMI/DVI IN
AUDIO (RGB/DVI) RGB(PC) REMOTE CONTROL IN
RS-232C IN (CONTROL & SERVICE)
AUDIO OUT
AV IN 1
VIDEO AUDIO
COMPONENT IN
VIDEO MONO ( ) AUDIO S-VIDEO
AV IN 2
32/37/42/47/52LG60
L/MONO R AUDIO VIDEO HDMI IN 4 USB IN
HDMI/DVI IN, HDMI IN Digital Connection. Supports HD video and Digital audio. Doesn’t support 480i. Accepts DVI video using an adapter or HDMI to DVI cable (not included) COMPONENT IN Analog Connection. Supports HD. Uses a red, green, and blue cable for video & red and white for audio. RGB (PC) Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable). AUDIO (RGB/DVI) 1/8” headphone jack for analog PC audio input. REMOTE CONTROL PORT For a wired remote control. RS-232C IN (CONTROL & SERVICE) PORT Used by third party devices. ANTENNA/CABLE IN Connect over-the air signals to this jack. Connect cable signals to this jack.
DIGITAL AUDIO OUT Digital audio output for use with amps and home theater systems. Includes an optical and/or coaxial connection. Note: In standby mode, these ports do not work. AUDIO OUT Analog audio output for use with amps and home theater systems. AV (Audio/Video) IN Analog composite connection. Supports standard definition video only (480i). S-VIDEO Better quality than standard composition. Supports standard definition video only (480i). USB INPUT Used for viewing photos and listening to MP3s. USB SERVICE ONLY or RS-232C IN (SERVICE ONLY) Used for software updates. Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power.

When using the remote control, aim it at the remote control sensor on the TV.
TV/STB/DVD/VCR
Select the remote operating mode: TV, STB, DVD, or VCR.
DVD
STB
VCR
POWER
Turns your TV or any other programmed equipment on or off, depending on the mode.
INPUT
Q.MENU
Select the desired quick menu source.
Displays the main menu. Clear all on-screen displays and return to TV viewing from any menu.
INPUT
External input modes rotate in regular sequence.
VOLUME UP
Increase/decrease the sound level.
FAV
Scroll through the programmed Favorite channels.
MUTE
Switch the sound on or off.
VOL CH
CHANNEL UP/DOWN
Select available channels.
PAGE UP/DOWN
Move from one full set of screen information to the next one.
Used to enter a program number for multiple program channels such as 2-1, 2-2, etc.
Tune to the last channel viewed.
VCR/DVD, USB,
Control video cassette recorders or DVD players. Control USB menu (PHOTO LIST and MUSIC LIST.) Control the SIMPLINK compatible devices.
NUMBER button · SIMPLINK Control buttons

Navigate the on-screen menus and adjust the system settings to your preference.
Allows the user to move return one step in an interactive application or other user interaction function.
See a list of AV devices connected to TV. When you toggle this button, the SIMPLINK menu appears at the screen.
AV MODE
It helps you select and set images and sounds.
IOpen the battery compartment cover on the back side and install
the batteries matching correct polarity (+with +,-with -).
IInstall two 1.5V AAA batteries. Don’t mix old or used batteries with
new ones.
IClose cover.
(Up/Down/Left · Right/ENTER)


Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
2 Assemble the parts of the STAND BODY with COVER BASE of the TV. 2
Fix the 4 bolts securely using the holes in the back of the TV.
Fix the 4 bolts securely using the holes in the back of the TV. 4


Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the parts of the STAND BODY with COVER BASE of the TV. 2
Fix the 4 bolts securely using the holes in the back of the TV. 4


I Here shown may be somewhat different from your TV.
Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT CLIP as shown. If your TV has the CABLE HOLDER, install it as shown and bundle the cables.
CABLE MANAGEMENT CLIP with both hands and pull it upward.
AGEMENT CLIP with both hands and pull it upward.
G Do not hold the CABLE MANAGEMENT CLIP when moving the TV.
- If the TV is dropped, you may be injured or the product may be broken.


Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section.
Align the hole with the tab on the CABLE MANAGEMENT CLIP. Turn the CABLE MANAGEMENT CLIP as shown. Note: This cable management can be broken by excessive pressure.
Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. Put the cables inside the CABLE MANAGEMENT CLIP and snap it closed.


For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.
G To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.


This TV accepts VESA FDMI compliant mounts via the four screw holes on the back of the TV. We recommend that you use a wall mounting bracket of LG brand when mounting the TV to a wall.
G Screw length needed depends on the wall mount used. For further information, refer to the instructions


You can remove the stand before installing the TV on a wall mount by performing the previous stand instructions in reverse. After removing the stand, install the included protection cover over the hole for the stand.
Insert the PROTECTION COVER into the TV until clicking sound.
After removing the protection paper from the protection cover, adhere it to the TV as shown.

I You should purchase necessary components to prevent TV from falling off of the stand.
I Image shown may differ from your TV.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.
I Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.
I Use a sturdy rope (not provided as parts of the product, must pur-
chase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.
G Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
G To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.

I To prevent damage do not connect to the power outlet until all connections are made between the devices.
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connection. For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments (Connect to wall antenna socket)
Outdoor Antenna (VHF, UHF)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Be careful not to bend the copper wire when connecting the antenna.
Cable TV Wall Jack
RF Coaxial Wire (75 ohm)
I To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
I If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
I If the antenna is not installed properly, contact your dealer for assistance.
ANTENNA/ CABLE IN
VHF
G The TV will let you know when the analog, cable, and digital channel scans are complete. NOTE !

I To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
I This part of EXTERNAL EQUIPMENT SETUP mainly use picture for 37/42/47/52LG50.
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
1. How to connect
Y L R P B P R
Connect the video outputs (Y, PB, PR) of the digital set- top box to the COMPONENT IN VIDEO 1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red).
Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO 1 jacks on the TV.
OPT DIGI
AUDIO (RGB/DVI) RGB(PC) REMOTE CONTROL IN
2. How to use
I Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box. operation)
I Select the Component 1 input source on the TV using
the INPUT button on the remote control.
AUDIO
I If connected to COMPONENT IN2 input, select the
Component 2 input source on the TV.
i.e) 37/42/47/52LG50
Y, CB/PB, CR/PR Supported Resolutions
Horizontal Vertical Frequency(KHz) Frequency(Hz)
15.73 59.94 15.73 60.00
31.47 59.94 31.50 60.00
44.96 59.94 45.00 60.00
33.72 59.94 33.75 60.00
26.97 23.976 27.00 24.00 33.71 29.97 33.75 30.00 67.432 59.94 67.50 60.00


Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red).
Connect the audio outputs of the DVD to the COMPONENT IN AUDIO1 jacks on the TV.
I Turn on the DVD player, insert a DVD.
I Select the Component 1 input source on the TV using
I If connected to COMPONENT IN 2 input, select the
I Refer to the DVD player's manual for operating instructions.
Connect the HDMI output of the DVD to the HDMI/DVI IN1, 2, 3 or 4 jack on the TV.
No separate audio connection is necessary. HDMI supports both audio and video.
I Select the HDMI1, HDMI2, HDMI3, or HDMI4 input
source on the TV using the INPUT button on the remote control.
I Refer to the DVD player's manual for operating instructions.

i.e) 37/42/47/52LG50
L R S-VIDEO VIDEO
Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
ANT OUT
OUTPUT SWITCH
2. How to use
ANTENNA/ CABLE IN
I Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
I Select the AV1 input source on the TV using the INPUT
REMOTE CONTROL IN
button on the remote control.
I If connected to AV IN2, select AV2 input source on the TV.
AUDIO OUT
NOTE !
L R
AV IN 1
G If you have a mono VCR, connect the audio cable from
the VCR to the AUDIO L/MONO jack of the TV.
VIDEO L R (MONO) AUDIO S-VIDEO
NT IN
S-Video Connection (Except 32/37/42/47/52LG60)
1. How to connect
i.e) 37/42/47/52LG50
Connect the S-VIDEO output of the VCR to the S -VIDEO input on the TV.
L R S-VIDEO VIDEO
Connect the audio outputs of the VCR to the AUDIO input jacks on the TV.
OUTPUT SWITCH
2. How to use
I Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
I Select the AV1 input source on the TV using the INPUT
button on the remote control.
REMOTE CONTROL IN
NOTE !
RS-232C IN (CONTROL & SERVICE)
AUDIO OUT
G S-Video provides better quality than composite. Use it
when available.
AV IN 1
AUDIO
NT IN
VIDEO L R (MONO) AUDIO S-VIDEO
CAUTION
G Do not connect to both Video and S-Video at the same
time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.


Connect the VGA output of the PC to the RGB (PC) jack on the TV.
Connect the PC audio output to the AUDIO (RGB/DVI) jack on the TV.
I Select the RGB-PC input source on the TV using the

32/42/47/52LG70
Horizontal Vertical Frequency(KHz) Frequency(Hz)
Horizontal Vertical Frequency(KHz) Frequency(Hz)
31.469 70.08
31.468 70.09 31.469 70.08 31.469 59.94 37.500 75.00 37.861 72.80 35.156 56.25 37.879 60.31 46.875 75.00 48.077 72.18 48.363 60.00 56.476 70.06 60.023 75.02 47.776 59.87 60.289 74.893 63.981 60.02 79.976 75.025 47.712 60.015 75.00 60.00 66.587 59.934 67.5 60.00
31.469 70.08
31.469 59.94
37.879 60.31
48.363 60.00
47.776 59.87
47.720 59.799
47.130 59.65
* Only RGB-PC mode
For 42/50PG25, 50/60PG60
* Only RGB-PC mode
Resolution Horizontal Vertical Frequency(KHz) Frequency(Hz)
31.468 70.09 31.469 70.08 31.469 59.94 37.500 75.00 37.861 72.80 35.156 56.25 37.879 60.31 46.875 75.00 48.077 72.18 48.363 60.00 56.476 70.06 60.023 75.02 47.776 59.87 60.289 74.893 63.981 60.02 79.976 75.025 47.712 60.015 75.00 60.00 66.587 59.934
* Only RGB-PC mode

TURNING ON TV
First, connect power cord correctly. At this moment, the TV switches to standby mode.
I In standby mode to turn TV on, press the , INPUT, (DE or ) button on the TV or press the POWER, INPUT, CH( or ), Number (0~9) button on the remote control.
Select the viewing source by using the INPUT button on the remote control.
I This TV is programmed to remember which power state it was last set to, even if the power cord is out.
When finished using the TV, press the POWERbutton on the remote control. The TV reverts to standby mode.
Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. Run Auto Tuning again after any Antenna/Cable connection changes.
Enter Move CHANNEL Enter Move CHANNEL
Press ‘Yes’ button to begin auto tuning.
5 RETURN
Select CHANNEL.
Return to the previous menu.
Return to TV viewing.
Select Auto Tuning.
Select Yes.
I A password is required to gain access to
Auto Tuning menu if the Lock System is turned on.
Run Auto tuning.


Q.Menu (Quick Menu) is a menu of features which users might use frequently.
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
I All available TV channels are searched and stored
I User can do manual channel selection and add or
I You can add or delete in the channel list. Channel Edit

I Select the desired picture format: Set by program,
4:3, 16:9, Zoom1, Zoom2, Just Scan.
I Select the Intelligent Sensor (Except 32/37/42LG30,
Plasma TV), Vivid, Standard, Cinema/ Cinema (Only for 50/60PG60), Sport, Game, Expert1, Expert2.
I Adjust the Backlight (Only LCD TV), Contrast,
Brightness, Sharpness, Color, Tint.
Contrast, Fresh Color, Noise Rreduction, Gamma, Black Level, Eye Care (Only LCD TV), Real Cinema (For LCD TV) / Film Mode (For Plasma TV), TruMotion (Only 32/37/42/47/52LG60, 32/42/47/52LG70).
WATCHING TV
to the default factory settings.
I Adjust the screen Resolution, Auto config, Position,
Size, Phase, Reset.
TruMotion Demo (32/37/42/47/52LG60, 32/42/47/52LG70 Only)
I Use this feature to see the difference TruMotion
makes.
I Auto Volume makes sure that the volume level
remains consistent whether you are watching a commercial or a regular TV program.
I By differentiating the human sound range from others,
it helps users listen to human voices better.
I Adjust the left/right sound of speaker.
I Select the Standard, Music, Cinema, Sport, and Game.
I SRS TruSurround XT, Treble, Bass: Adjust the sound
to suit your taste and room situations.
to the default factory settings.
I Turn the TV speaker On or off.
channel signal. Select your viewing area time zone. Select Auto, Off, On depending on whether or not your viewing area observes Daylight Saving time.
I Manual: Set the clock manually.
I Select On or Off.
I Select On or Off.
I Select the amount of time before your TV turns off
automatically: Off, 10, 20, 30, 60, 90, 120, 180, 240.
I TV will be automatically turned off, in case of no
signal for 10 minutes.


I Select your desired language for on screen menus
I Control and play other AV devices connected to the TV
I This feature can be used to prevent unauthorized
I When selecting Off, Submenus for Analog, DTV, and
I Analog: CC1~ CC4 , Text1~ Text4.
I Digital: CC1~ CC4 , Text1~ Text4, Service1~ Service6.
I Use it to minimize any fixed image on the screen.
I After turning on the TV, adjust Mode, Time, Language,
I Select a channel number that you wish to block.
I Blocks movies according to the movie ratings limits
I Based on the ratings, blocks certain TV programs
that you and your family do not want to view.
I This function may become available in the future and
I Enables you to select a source to block from the
Screen Display) may differ slightly from that shown in this manual.

* This feature is only for 37/42/47/52LG50, 32/37/42/47/52LG60, 32/42/47/52LG70, Plasma TV.
When you connect a USB device, this screen is displayed automatically. In USB device, you can not add a new folder or delete the existing folder.
Connect the USB device to the USB IN jacks on the side of TV.
I It doesn’t support USB HDD
I This TV supports JPG and MP3.
When removing the USB device
Select the USB Eject menu before removing the USB device.
1 Q. MENU
Select PHOTO LIST or MUSIC LIST.
Select USB Eject.
ENTER
ENTER
Precautions when using the USB device
G Only a USB storage device is recognizable.
G Please use only a USB storage device which was
G If the USB storage device is connected through a
formatted as a FAT or NTFS file system provided with the Windows operating system. In case of a storage device formatted as a different utility pro- gram which is not supported by Windows, it may not be recognized.
USB hub, the device is not recognizable.
G A USB storage device using an automatic recogni-
tion program may not be recognized.
G A USB storage device which uses its own driver
may not be recognized.
G Please connect power to a USB storage device
which requires an external power supply. If not, the device may not be recognized.
G In case of a card reader, up to four memory cards
are concurrently recognizable.
G Please connect a USB storage device with cable is
G The recognition speed of a USB storage device
offered by USB maker. If connected with cable is not offered by USB maker or an excessively long cable, the device may not be recognized.
may depend on each device.
G Please do not turn off the TV or unplug the USB
device when the connected USB storage device is working. When such device is suddenly separated or unplugged, the stored files or the USB storage device may be damaged.
G Some USB storage devices may not be supported
or operated smoothly.
G File alignment method of USB storage device is
similar to Window XP and filename can recognize up to 100 English characters.
G Please do not connect the USB storage device
which was artificially maneuvered on the PC. The device may cause the product to malfunction or fail to be played. Never forget to use only a USB storage device which has normal music files or image files.
G Please backup important files because data on
USB device may be damaged. Data management is consumer's responsibility and as a result, the man- ufacturer does not cover data damage.

You can view .JPG files from USB storage devices. The On Screen Display on your model may be slightly different.
1 MENU ENTER ENTER
Select USB. Select PHOTO LIST. 2
Moves to upper level file
Page 1/1 No Marked PHOTO LIST
USB
Total number of marked photos
Corresponding buttons on the remote control
Navigate PopUp Menu Move Page Mark Exit
Photo Selection and Popup Menu
Page 1/1 No Marked PHOTO LIST
Select the target folder or drive.
Navigate Move Page Mark Exit CH FAV RETURN PopUp Menu
Show the Popup menu. 3
ENTER
Page 1/1 No Marked PHOTO LIST
4 Select the desired Popup menu.
Upper Photo X.Box 1366x768 125KB View
1366x768 125KB
Navigate Move Page Mark Exit CH FAV RETURN PopUp Menu
I Use the CH button to navigation in the photo page.
When you select a file (not folder), this PopUp menu is displayed.
I Use the FAV button to mark or unmark a photo.
When one or more photos are marked, you can view individual photos or a slide show of the marked photos. If no photos are marked, you can view all photos individually or all photos in the folder in a slide show.
G View: Display the selected item.
G Mark All: Mark all photos on the screen.
G Unmark All: Deselect all marked photos.
G Delete: Delete the selected photo item.
G Cancel: Close the pop-up menu.

You can change the Photo List view so that it fills the screen. More operations are available in full screen mode.
Page 1/1 No Marked PHOTO LIST
Select the target folder or drive.
Select the desired photos.
Navigate Move Page Mark Exit CH FAV RETURN PopUp Menu
USB
ENTER
Show the Popup menu.
Page 1/1 No Marked PHOTO LIST
Select View.
Upper Photo X.Box 1366x768 125KB
1366x768 125KB
The selected photo is displayed in full size.
Navigate Move Page Mark Exit CH FAV RETURN PopUp Menu
Select the Sideshow, BGM, (Rotate), Delete, Option, or Hide.
slide show. If no photo is selected, all photos in the cur- rent folder are displayed during slide show.
I Set the time interval of the slide show in Option.
I A slide show continues for a maximum of 4 hours.
Sideshow BGM Delete Option Hide
After 4 hours, the slide show will end and go to TV mode or external input mode.
The aspect ratio of a photo may change the size of the photo displayed on the screen in full size.
G BGM: Listen to music while viewing photos in full size.
I Set the BGM device and album in Option.
G (Rotate): Rotate photos.
Press F G to set the time interval between slides.
I Rotates the photo 90°, 180°, 270°, 360° clockwise.
G Delete: Delete photos.
... Music Folder
Folder.
I Use button and ENTER button to set values. Then go to and press ENTER to save the set- tings.
I You cannot change Music Folder while BGM is
playing.
G Hide : Hide the menu on the full-sized screen.
G This TV will not be able to decode
I To see the menu again on the full-sized screen, press
most JPG images saved using the Progressive option.
ENTER button to display.


You can use the Music List menu to play MP3 files form a USB storage device. This TV cannot play back copy-protected files. The On Screen Display on your model may be slightly different.
Supported music file: *.MP3 Bit rate range 40Kbps ~ 320Kbps • Sampling rate (Sampling Frequency) MPEG1 : 32000, 44100, 48000Hz MPEG2 : 16000, 24000, 22050Hz MPEG2.5 : 16 ~ 48KHz
Preview: If any album jacket for the file exists, this jack- et is displayed.
Navigate PopUp Menu Move Page Mark Exit CH FAV RETURN

Up to 6 music titles are listed per page.
Page 1/1 No Marked MUSIC LIST
Select the target folder or drive.
04:12
05:30
3945 KB, 128 Kbps
Select the desired musics.
Navigate Move Page Mark Exit CH FAV RETURN PopUp Menu
show the PopUp menu.
Page 1/1 No Marked MUSIC LIST
ENTER
Select the desired PopUp menu.
3945 KB 128 Kbps Play
5RETURN Return to TV viewing.
3945 KB, 128 Kbps
Navigate Move Page Mark Exit CH FAV RETURN PopUp Menu
I Use the CH button to navigation in the music page.
G Play (During stop): Play the selected music.
I Use FAV button to mark or unmark a music
Once a song finishes playing, the next selected one will be played. When there are no selected musics to play, the next one in the current fold- er will be played. If you go to a different folder and press the ENTER button, the current music in playback will stop.
file. If no music is marked, all the music in the folder will be played in sequence. When one or more music files are marked, the marked music files will be played in sequence. If you want to listen to only one song repeatedly, just mark that one file and play.
a music finishes playing, the next selected one will be played automatically.
I The play information box (as shown below) will
automatically move across the screen when there is no user input to prevent a fixed image remain- ing on the screen for a extended period of time.
ing musics.
musics and then move to the Photo List.
G Mark All: Mark all musics in the folder.
G Unmark All: Deselect all marked music.
G Delete: Delete the selected music.
G Cancel: Close the pop-up menu.
G When music is playing, is displayed in front of the music play time.
G A damaged or corrupted music file that does not play displays 00:00 as the play time.
G Music files with copy-protection will not play.
G Press ENTER, A , or RETURN button to stop the screen saver.
G This TV can not play music files less than 16 Kbytes.

TROUBLESHOOTING
The operation does not work normally.
I Check to see if there is any object between the product and the remote control
causing obstruction. Ensure you are pointing the remote control directly at the TV.
I Ensure that the batteries are installed with correct polarity (+ to +, - to -).
I Ensure that the correct remote operating mode is set: TV, VCR etc.
I Install new batteries.
I Is the sleep timer set?
I Check the power control settings. Power interrupted.
The video function does not work.
I Check whether the product is turned on.
I Try another channel. The problem may be with the broadcast.
I Is the power cord inserted into wall power outlet?
No picture &No sound
I Check your antenna direction and/or location.
I Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.
I This is normal, the image is muted during the product startup process. Please
contact your service center, if the picture has not appeared after five minutes.
I Adjust Color in menu option.
I Keep a sufficient distance between the product and the VCR.
No or poor color
I Try another channel. The problem may be with the broadcast.
I Are the video cables installed properly?
I Activate any function to restore the brightness of the picture.
I Check for local interference such as an electrical appliance or power tool.
I Station or cable product experiencing problems, tune to another station.
I Station signal is weak, reorient antenna to receive weaker station.
I Check for sources of possible interference.
I Check antenna (Change the direction of the antenna).
I Check HDMI cable over version 1.3.
No picture when connecting HDMI
The HDMI cables don’t support HDMI version 1.3, it cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.

The audio function does not work.
I Press the VOL or VOLUME button.
I Sound muted? Press MUTE button.
Picture OK & No sound
I Try another channel. The problem may be with the broadcast.
I Are the audio cables installed properly?
No output from one
I Adjust Balance in menu option.
I A change in ambient humidity or temperature may result in an unusual noise
when the product is turned on or off and does not indicate a fault with the product.
I Check HDMI cable over version 1.3.
No sound when connecting HDMI
I Check USB cable over version 2.0.
I Use normal MP3 file.
There is a problem in PC mode. (Only PC mode applied)
I Adjust resolution, horizontal frequency, or vertical frequency.
The signal is out of range
I Check the input source.
Vertical bar or stripe on
background & Horizontal Noise &
I Work the Auto configure or adjust clock, phase, or H/V position. (Option)
I Check the signal cable.
Screen color is unstable
I Reinstall the PC video card.
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
I To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
G If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.

37LG30 (37LG30-UA) (37LG30-UD)
42LG30 (42LG30-UA) (42LG30-UD)
MODELS
31.5 x 23.7 x 8.9 inches 801.8 x 604.2 x 227.3 mm 31.5 x 21.4 x 3.1 inches 801.8 x 544.1 x 79.0 mm
36.2 x 26.8 x 11.5 inches 919.6 x 682.3 x 293.8 mm 36.2 x 24.0 x 3.5 inches 919.6 x 610.3 x 89.0 mm
40.6 x 29.2 x 11.5 inches 1032.8 x 742.3 x 293.8 mm 40.6 x 26.3 x 3.6 inches 1032.8 x 670.1 x 92.0 mm
Dimensions (Width x Height x Depth)
With stand Without stand
29.5 pounds / 13.4 kg 26.2 pounds / 11.9 kg
41.4 pounds / 18.8 kg 35.7 pounds / 16.2 kg
52.0 pounds / 23.6 kg 46.2 pounds / 21.0 kg
42LG50 (42LG50-UA) (42LG50-UG)
MODELS
36.8 x 26.9 x 11.5 inches 936.4 x 685.4 x 293.4 mm 36.8 x 24.1 x 3.4 inches 936.4 x 612.8 x 88.0 mm
40.7 x 28.9 x 11.5 inches 1034.0 x 735.0 x 294.0 mm 40.7 x 26.1 x 3.5 inches 1034.0 x 663.0 x 91.0 mm
Dimensions (Width x Height x Depth)
With stand Without stand
40.3 pounds / 18.3 kg 34.3 pounds / 15.6 kg
54.0 pounds / 24.5 kg 48.5 pounds / 22.0 kg
52LG50 (52LG50-UA) (52LG50-UG)
MODELS
45.5 x 32.0 x 13.5 inches 1156.2 x 813.1 x 342.9 mm 45.5 x 29.1 x 4.0 inches 1156.2 x 739.2 x 103.0 mm
50.8 x 35.1 x 13.5 inches 1291.7 x 892.2 x 342.9 mm 50.8 x 32.1 x 4.5 inches 1291.7 x 817.0 x 115.3 mm
Dimensions (Width x Height x Depth)
64.3 pounds / 29.2 kg 54.2 pounds / 24.6 kg
87.0 pounds / 39.5 kg 76.9 pounds / 34.9 kg
With stand Without stand
Power requirement Television System Program Coverage External Antenna Impedance
AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
Operating Temperature Operating Humidity
32 ~ 104°F (0 ~ 40°C) Less than 80%
Storage Temperature Storage Humidity
I The specifications shown above may be changed without prior notice for quality improvement.

37LG60 (37LG60-UA)
42LG60 (42LG60-UA)
MODELS
31.7 x 24.6 x 13.1 inches 805.6 x 626.0 x 333.0mm 31.7 x 23.1 x 3.7 inches 805.6 x 587.4 x 96.2 mm
36.5 x 27.8 x 14.7 inches 929.0 x 706.9 x 374.7 mm 36.5 x26.1 x 3.8 inches 929.0 x 665.0 x 98.7 mm
40.8 x 31.3 x 14.9 inches 1037.8 x 796.4 x 379.5 mm 40.8 x 29.4 x 3.1 inches 1037.8 x 747.0 x 80.8 mm
Dimensions (Width x Height x Depth)
With stand Without stand
31.7 pounds / 14.4 kg 26.8 pounds / 12.2 kg
46.7 pounds / 21.2 kg 39.9 pounds / 18.1 kg
53.1 pounds / 24.1 kg 44.9 pounds / 20.4 kg
47LG60 (47LG60-UA)
45.3 x 34.1 x 17.1 inches 1152.8 x 868.6 x 434.5 mm 45.3 x 32.3 x 3.1 inches 1152.8 x 820.8 x 79.0 mm
50.3 x 37.1 x 16.9 inches 1280.1 x 944.7 x 430.0 mm 50.3 x 35.2 x 3.5 inches 1280.1 x 896.0 x 89.0 mm
Dimensions (Width x Height x Depth)
With stand Without stand
71.8 pounds / 32.6 kg 59.3 pounds / 26.9 kg
99.2 pounds / 45.0 kg 83.9 pounds / 38.1 kg
MODELS 32LG70 (32LG70-UA)
42LG70 (42LG70-UA)
Dimensions (Width x Height x Depth)
31.3 x 23.5 x 8.9 inches 797.0 x 597.0 x 227.3 mm 31.3 x 21.9 x 3.9 inches 797.0 x 558.6 x 100.5 mm
40.4 x 28.8 x 11.5 inches 1026.2 x 734.0 x 293.4 mm 40.4 x 27.0 x 4.4 inches 1026.2 x 687.9 x 111.8 mm
28.4 pounds / 12.9 kg 25.1 pounds / 11.4 kg
49.3 pounds / 22.4 kg 43.4 pounds / 19.7 kg
With stand Without stand
52LG70 (52LG70-UA)
44.8 x 32.2 x 13.5 inches 1140.4 x 820.1 x 342.9 mm 44.8 x 30.1 x 5.0 inches 1140.4 x 764.8 x 129.0 mm
50.5 x 35.3 x 13.5 inches 1284.4 x 898.6 x 342.9 mm 50.5 x 33.2 x 5.0 inches 1284.4 x 844.6 x 129.5 mm
Dimensions (Width x Height x Depth)
With stand Without stand
66.3 pounds / 30.1 kg 55.9 pounds / 25.4 kg
87.9 pounds / 39.9 kg 77.6 pounds / 35.2 kg
Power requirement Television System Program Coverage External Antenna Impedance
AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
Operating Temperature Operating Humidity
32 ~ 104°F (0 ~ 40°C) Less than 80%
Storage Temperature Storage Humidity
I The specifications shown above may be changed without prior notice for quality improvement.

42PG25 (42PG60-UA)
50PG25 (50PG60-UA)
Dimensions (Width x Height x Depth)
41.1 x 28.9 x 12.1 inches 1044.4 x 735.4 x 308.0 mm 41.1 x 26.7 x 3.1 inches 1044.4 x 680.6 x 79.6 mm
48.6 x 33.4 x 14.3 inches 1235.6 x 849.3 x 364.1 mm 48.6 x 31.2 x 3.1 inches 1235.6 x 792.8 x 79.6 mm
With stand Without stand
61.7 pounds / 28.0 kg 55.1 pounds / 25.0 kg
96.3 pounds / 43.7 kg 87.5 pounds / 39.7 kg
60PG60 (60PG60F-UA)
48.6 x 33.4 x 14.3 inches 1235.6 x 849.3 x 364.1 mm 48.6 x 31.2 x 3.1 inches 1235.6 x 792.8 x 79.6 mm
57.3 x 38.8 x 16.3 inches 1455.0 x 985.0 x 414.0 mm 57.3 x 36.4 x 3.3 inches 1455.0 x 924.8 x 84.1 mm
Dimensions (Width x Height x Depth)
With stand Without stand
100.7 pounds / 45.7 kg 91.9 pounds / 41.7 kg
137.5 pounds / 62.4 kg 121.0 pounds / 54.9 kg
Power requirement Television System Program Coverage External Antenna Impedance
AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
Operating Temperature Operating Humidity
32 ~ 104°F (0 ~ 40°C) Less than 80%
Storage Temperature Storage Humidity
I The specifications shown above may be changed without prior notice for quality improvement.
OPEN SOURCE SOFTWARE NOTICE - This feature is not available for all models.
The following GPL executables and LGPL/MPL libraries used in this product are subject to the GPL/LGPL/MPL License Agreements:
performing such distribution, such as the cost of media, shipping and handling upon e-mail request to LG Electronics at: Opensource@lge.com This offer is valid for a period of three(3) years from the date of the distribution of this product by LG Electronics. You can obtain a copy of the GPL, LGPL and MPL licenses on the CD-ROM provided with this product.
I Linux kernel 2.6.12
I This software is based in part on the work of the
Independent JPEG Group.
I This software includes the Zlib compression
library, developed by Jean-loup Gailly and Mark Adler. Copyright (C) 1995-2005 Jean-loup Gailly and Mark Adler
LG Electronics offers to provide source code to you on CD-ROM for a charge covering the cost of


Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.