
Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA).
As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
www.lgcommercial.com
(Only 32LG3DC model)



WARNING / CAUTION
To prevent fire or shock hazards, do not expose this product to rain or moisture.
DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO
Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the litera- ture accompanying the appliance.
different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV
technician for help.
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product

IMPORTANT SAFETY INSTRUCTIONS
Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction:
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Do not use this apparatus near water.
Clean only with dry cloth.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Only use attachments/accessories specified by the manufacturer.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.
Unplug this apparatus during lighting storms or when unused for long periods of time.
When mounting a TV it on the wall, make sure not to install TV by the hanging power and sig- nal cables on the back of the TV.

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Never touch this apparatus or antenna during a thunder or lighting storm.
Outdoor use marking : WARNING - To reduce the risk of fire or elec- tric shock, do not expose this appliance to rain or moisture.
Do not allow a impact shock or any objects to fall into the product, and do not drop onto the screen with something.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.
Wet Location Marking : Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on or over apparatus.
GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
CAUTION concerning the Power Cord : Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates dam- age or deterioration, unplug it, discontinue use
DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable.
Power Supply · Short-circuit · Breaker


APPENDIX
Auto Volume Leveler (Auto Volume) 53 Clear Voice 54 Preset Sound Setting (Sound Mode) 55 Sound Setting Adjustment - User Mode 56 Balance 58 TV Speakers On/Off Setup 59 Audio Reset 60 Stereo/SAP Broadcasts Setup 61 Audio Language 62 On-Screen Menus Language Selection 63 Caption Mode
Troubleshooting 81 Maintenance 83 Product Specifications 83 IR Codes 84
- Analog Broadcasting System Captions 64 - Digital Broadcasting System Captions 65 - Caption Option 66
- Auto Clock Setup 67 - Manual Clock Setup 68 Auto On/Off Time Setting 69 Sleep Timer Setting 70 Auto Shut-off Setting 71
Set Password & Lock System 72 Channel Blocking 75 Movie & TV Rating 76 Downloadable Rating 79 External Input Blocking 80

LG's own special digital image generator, consisting of a full digital image processor, six different main picture quality factors.
Manufactured under license from Dolby Laboratories. “Dolby “and the double-D symbol are trademarks of Dolby Laboratories.
High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions.
is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.

ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below.

Copyright© 2007 LGE, All Rights Reserved.
CD Manual
Bolts for stand assembly
Protective Bracket and Bolt for Power
(Refer to P.14) Screw for stand fixing
Protection Cover
(Refer to P.11) (only 32LG3DC model)
(Refer to P.13) (only 32LG3DC model)
Cord (Refer to P.12)

Shown herein is an optional Installer remote control available for the 26/32LG3DCH models only. The installer remote control is NOT included with the TV.
* Wipe spots on the exterior only with the polishing cloth.
* Do not wipe roughly when removing stain. Please be cautions of that excessive pressure may cause scratch or discoloration. Polishing Cloth (This feature is not available
When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance.

FRONT PANEL INFORMATION
I Image shown may differ from your TV.
I NOTE: If your TV has a protection tape attached, remove the tape.
And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it).

Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the set is switched on.

Power/Standby Indicator Illuminates red in standby mode. Illuminates green when the set is switched on.

I Image shown may differ from your TV.



HDMI/DVI IN HDMI/DVI IN USB IN USB IN SERVUCE ONLY SERVUCE ONLY
AV (Audio/Video) IN Connect audio/video output from an external device to these jacks. S-VIDEO Connect S-Video out from an S-VIDEO device.
AUDIO IN (RGB/DVI) Connect the audio from a PC or DTV.
SPEAKER OUT 8 Ω
HDMI/DVI IN Digital Connection. Supports HD video and Digital audio. Accepts DVI video using an adapter or HDMI to DVI cable (not included)
Plug the headphone into the headphone socket.
For operation with AC power. Caution: Never attempt to operate the TV on DC power.
USB IN SERVICE ONLY Used for software updates.
ANTENNA IN Connect over-the air signals to this jack.
RS-232C IN (SERVICE ONLY) Used by third party devices.
M.P. I.
PILLOW SPEAKER (only 26/32LG3DCH model) Used to connect to pillow speaker. SPEAKER SWITCH (only 26/32LG3DCH model) Used to select the speaker output switch. Note: If Pillow Speaker is selected, no Sound will be heard from TV speakers. Switch (NORMAL SPEAKER or PILLOW SPEAKER.)
air signals to this jack.
COMPONENT IN Connect a component video/audio device to these jacks.

I Image shown may differ from your TV.
I When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the
product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can
deviate from abrasion of the tightening part of the bolt.
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the parts of the STAND BODY with COVER BASE of the TV. Assemble the TV as shown.

Fix the 4 bolts securely using the holes in the back of the TV. 4

CABLE MANAGEMENT
I Image shown may differ from your TV.
Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section. Secure the power cable with the PROTECTIVE BRACKET and the Bolt as shown. It will help prevent the power cable from being removed by accident.

Install the CABLE MANAGEMENT CLIP as shown.
Put the cables inside the CABLE MANAGEMENT CLIP and snap it closed. 3

I Image shown may differ from your TV.
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
4 inches 4 inches
G Ensure adequate ventilation by following the clearance recommendations.
The TV can be conveniently swivelled on its stand 90° to the left or right to provide the optimum viewing angle.

The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw.
G To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.
4 inches · 4 inches

VESA WALL MOUNTING
This TV accepts VESA FDMI compliant mounts via the four screw holes on the back of the TV. We recom- mend that you use an LG brand wall mount when mounting the TV to a wall.

G Screw length needed depends on the wall mount used. For further information, refer to the instructions
You can remove the stand before installing the TV on a wall mount by performing the previous stand instruc- tions in reverse. After removing the stand, install the included protection cover over the hole for the stand.
Insert the PROTECTION COVER into the TV until clicking sound.

I You should purchase necessary components to prevent TV from falling off of the stand.
I Image shown may differ from your TV.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.

I Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.
I Use a sturdy rope (not provided as parts of the product, must pur-
chase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.

G Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
G To use the TV safely, make sure that the height of the bracket on the wall and the one on the TV are

I To prevent damage do not connect to the power outlet until all connections are made between the devices.

Wall Antenna Socket or Outdoor Antenna without a Cable Box Connection. For optimum picture quality, adjust antenna direction if needed.
Be careful not to bend the copper wire when connecting the antenna.

I To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
I If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
I If the antenna is not installed properly, contact your dealer for assistance.


I To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
I This part of EXTERNAL EQUIPMENT SETUP mainly use picture for 32LG3DC model.
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.
Component Connection
1. How to connect


Connect the video outputs (Y, PB, PR) of the digital set- top box to the COMPONENT IN VIDEO jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red).
Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO jacks on the TV. 2
I Turn on the digital set-top box.
I Select Component input source with using the INPUT
button on the remote control.



HDMI Connection
1. How to connect

Connect the digital set-top box to HDMI/DVI IN jack on the TV.

No separate audio connection is necessary. HDMI supports both audio and video.
I Turn on the digital set-top box.
I Select HDMI/DVI input source with using the INPUT
button on the remote control.


1. How to connect


Connect the DVI output of the digital set-top box to the HDMI/DVI IN jack on the TV.
Connect the audio output of the digital set-top box to the AUDIO IN(RGB/DVI) jack on the TV.
ual for the digital set-top box.)
I Select the HDMI/DVI input source on the TV using the
INPUT button on the remote control.

connection. DVI doesn't support audio, so a separate audio connection is necessary.

DVD SETUP
Component Connection
1. How to connect

Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT IN VIDEO jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red).

Connect the audio outputs of the DVD to the COMPONENT IN AUDIO jacks on the TV.
I Turn on the DVD player, insert a DVD.
INPUT button on the remote control.
I Refer to the DVD player's manual for operating instructions.
Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below.


1. How to connect


Connect the S-VIDEO output of the DVD to the S -VIDEO input on the TV.
Connect the audio outputs of the DVD to the AUDIO input jacks on the TV.
I Turn on the DVD player, insert a DVD.
button on the remote control.
I Refer to the DVD player's manual for operating instructions.
1. How to connect

Connect the HDMI output of the DVD to the HDMI/DVI IN jack on the TV.

No separate audio connection is necessary. HDMI supports both audio and video.
INPUT button on the remote control.
I Refer to the DVD player's manual for operating instructions.

VCR SETUP
I To avoid picture noise (interference), leave an adequate distance between the VCR and TV. If the 4:3
picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all TVs and is not covered by warranty.
Antenna Connection
1. How to connect
Connect the RF antenna out socket of the VCR to the ANTENNA IN socket on the TV.
L R S-VIDEO VIDEO
ANT OUT
Connect the antenna cable to the RF antenna in socket of the VCR.
ANT IN
Wall Jack
2. How to use
I Set VCR output switch to 3 or 4 and then
Antenna
tune TV to the same channel number.
PLAY on the VCR. (Refer to the VCR owner’s manual.)


1. How to connect
Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
I Insert a video tape into the VCR and press PLAY on the
I Select the AV1 input source on the TV using the INPUT
button on the remote control.
I If connected to AV IN2, select AV2 input source on the TV.

from the VCR to the AUDIO L(MONO) jack of the TV.

1. How to connect

Connect the S-VIDEO output of the VCR to the S -VIDEO input on the TV.
Connect the audio outputs of the VCR to the AUDIO input jacks on the TV.
I Insert a video tape into the VCR and press PLAY on the
I Select the AV1 input source on the TV using the INPUT
button on the remote control.


and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.

OTHER A/V SOURCE SETUP
1. How to connect
Video Game Set Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors. (Video = yellow, Audio Left = white, and Audio Right = red)


2. How to use
I Select the AV2 input source on the TV using
the INPUT button on the remote control.
input source on the TV.
I Operate the corresponding external equipment.

I Connect a pillow speaker to the LCD TV/Monitor.
Connect the PILLOW SPEAKER output jack on the back of the TV.
Connect an acccessory pillow speaker or wired remote control unit to this 6-pin jack.
SPEAKER SWITCH SPEAKER SWITCH
Select PILLOW SPEAKER on the rear panel of the TV.
sound will be heard from the TV speakers. If pillow speaker switch is set to the Pillow Speader position, Auto Volume will be grayed out and not accessible on the Sound menu.
Pillow speaker not included with TV.
Use a pillow speaker by Curbell, Model A-16455-02 or other UL recognized pendant control bearing the warning: “Risk of fire if used in oxygen enriched atmosphere. Keep pen- dant control away from oxygen equipment.”
Controlling the TV with Serial Data The TV is capable of being controlled by a single-wire, serial data signal. This is a LG patented technology and is being implemented by certain brands of “smart” pillow speakers, such as Curbell’s “GEN-II” models.
Pillow Speaker Interface This connector furnishes three control lines and an audio output. A patient-pendant remote control, or entertainment audio and nurse call system may be connected here. All lines are isolated from the AC power line and earth ground. (Optoisolators isolate the control lines, and a transformer isolates the audio. There are no relays or inductive components in the control lines.)
pin No.
External TV On/Off switch. (Not used.) External Channel Up switch or Data in. Common connection for control, data, and audio output. Impedance to earth ground is a 10-meg resistor in parallel with a 1100 pf capacitor. Isolated audio output. Nominal 14-ohm source impedance with short circuit protection. Intended for a pillow speaker with a low-impe ance pad-type volume control. External Channel Down switch.
Controlling the TV with Mechanical Switches Pin 4(common) is momentarily connected to pin 1, 3, or 6 via push-action switches to control On/Off and Channel Up/Down. These pins are at +13volts DC(when measured from pin4) with the switches open. Current draw is 8 mA when a switch is closed. (This operation is identical to previous LG models using the 5-Wire Interface except that only +7 volts DC was supplied and current draw was only 2.5 mA.)
(only 26/32LG3DCH model)

PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

Connect the VGA output of the PC to the RGB IN(PC) jack on the TV.
Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the TV.
VIDEO NO ) RGB IN (PC) RGB IN (PC)

1. How to connect


Connect the DVI output of the PC to the HDMI/DVI IN jack on the TV.
Connect the PC audio output to the AUDIO IN (RGB/DVI) jack on the TV.
I Turn on the PC and the TV.
INPUT button on the remote control.

may not work if a HDMI to DVI Cable is in use.
with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
long period of time. The fixed image could become permanently imprinted on the screen.
tion settings may not allow the image to be positioned on the screen properly.

Screen Setup for PC mode

You can choose the resolution in RGB-PC mode. The Position, Phase, and Size can also be adjusted.

Select the desired resolution.
Select Screen (RGB-PC).


Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, try using the manual settings or a different resolution or refresh rate on the PC.
Select PICTURE. 1

Select Screen (RGB-PC).
Select Auto config..
Start Auto Configuration. 5

Adjustment for screen Position, Size, and Phase

If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This feature operates only in RGB-PC mode.
Select PICTURE.

Select Screen (RGB-PC).
vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. The Size adjustment range is -30 ~ 30.
Select Position, Size, or Phase.
Make appropriate adjustments.
remove any horizontal noise and clear or sharpen the image of characters. The Phase adjustment range is -32 ~ 31.


Returns Position, Size, and Phase to the default factory settings. This feature operates only in RGB-PC mode.
Select PICTURE.
Select Screen (RGB-PC).
Select Yes. 4

REMOTE CONTROL FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
Turns your TV on or off.
TV
In AV, Component, RGB-PC, and HDMI/DVI input sources, screen returns to the last TV channel.
PICTURE SOUND RATIO
SAP
INPUT
External input modes rotate in regular sequence: TV, AV, Component, RGB-PC, and HDMI/DVI. (AV, Component, RGB-PC, and HDMI/DVI input sources are linked automatically, only if a device is connected.)
PICTURE
Selects the factory preset picture depend on the viewing environment. G p.44
SOUND
Selects the factory preset sound for type of program.
G p.56
TIMER
SAP
Analog mode: Selects MTS sound (Mono, Stereo, or a SAP) G p.61 DTV mode: Changes the audio language.
MUTE
MENU ADJUST RETURN
RATIO
Change the aspect ratio. G p.42
THUMBSTICK
Navigate the on-screen menus and adjust the system set- tings to your preference.
(only 32LG3DC model) · (Up/Down/Left · Right/ENTER)

— (DASH)
Used to enter a program number for multiple program channels such as 2-1, 2-2, etc.
Tune to the last channel viewed.
VOLUME UP
Increase/decrease the sound level.
TIMER
Select the amount of time before your TV turns off automatically. G p.70
MUTE
Switch the sound on or off. G p.35
CHANNEL UP/DOWN
Select available channels.
Adjust the screen resolution, position, size and phase. G p.30
Displays the main menu.
Allows the user to move return one step in an interactive application or other user interac- tion function.
the batteries matching correct polarity (+with +,-with -).
IInstall two 1.5V AAA batteries. Don’t mix old or used batteries with
new ones.
IClose cover.
(only 32LG3DC model)

WATCHING TV / CHANNEL CONTROL
TURNING ON TV
First, connect power cord correctly. At this moment, the TV switches to standby mode.
I In standby mode to turn TV on, press the , INPUT, CH (+ or -)but- ton on the TV or press the POWER, INPUT, CH(+ or -), Number (0~9) button on the remote control.
Select the viewing source by using the INPUT button on the remote control.
I This TV is programmed to remember which power state it was last set to,
even if the power cord is out.
When finished using the TV, press the POWER button on the remote con- trol. The TV reverts to standby mode.
G If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

Press the CH (+ or -) or NUMBER buttons to select a channel number. 1
Adjust the volume to suit your personal preference.
Press the VOL (+ or -) button to adjust the volume.
If you want to switch the sound off, press the MUTE button.
You can cancel the Mute function by pressing the MUTE or VOL (+ or -) button.


Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.


Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. Run Auto Tuning again after any Antenna/Cable connection changes.

Select CHANNEL.
Select Auto Tuning.
Auto Tuning menu if the Lock System is turned on.
Select Yes.
Run Auto tuning.


If selecting DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the quality of the signal being received.
Select CHANNEL. 1

Select Manual Tuning.
Select DIGITAL or ANALOG.
Manual Tuning menu if the Lock System is turned on.
Select channel you want to add or delete.


A custom list can be created by toggling each channel on or off with ENTER button. The channels in the Custom List are displayed in black and the channels deleted from the Custom List are displayed in gray. Once a channel is highlighted you can add or delete the channel by referring to the small window at the top- right corner of the screen.
Add/Delete Move Page CH Move Previous RETURN Exit MENU
ENTER Select Channel Edit.
Select a channel.
Select channel you want to add or delete.
RETURN Return to TV viewing.


Choose preset labels for your channels. If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a channel even if you didn't preset a label for the channel.
Select CHANNEL.
Select Channel Label.
Auto Tuning menu if the Lock System is turned on.
Select Channel.
Select the appropriate logo for the channel. 5

Only these input signals which are connected to a TV can be activated and selected.

TV AV1 AV2 Component RGB
Select the desired input source. 1
TV AV1 AV2
I TV: Select it to watch over-the-air, cable
and digital cable broadcasts.
other external equipment.
DVD or a Digital set-top box.
I RGB: Select it to view PC input.
ition devices.
Component HDMI RGB

PICTURE SIZE (ASPECT RATIO) CONTROL
This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV.
I RGB-PC input source use 4:3 or 16:9 aspect ratio.

G If a fixed image is displayed on the screen for a long time, the image could become imprinted on the
screen and remain visible. This phenomenon is common to all manufacturers and is not covered by warranty. Although, after watch- ing video that did not fill the screen, any after-image from the black bars will normally dissipate after a few minutes.

Set by program Selects the proper picture proportion to match the source’s image.
Zoom 1 Choose Zoom 1 when you want to view the pic- ture without any alteration. However, the top and bottom portions of the picture will be cropped.


Zoom 2 Choose Zoom 2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage.


4:3 Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio.

Just Scan Following selection will lead to you view the pic- ture of best quality without loss of original pic- ture in high resolution image. Notes: If there are noise in original picture, you can see the noise at the edge. Just Scan operates only in DTV/CADTV/Component/HDMI-DTV/DVI-DTV (720p/1080i/1080p) input source.
16:9 Adjust the picture horizontally, in a linear pro- portion to fill the entire screen.



PRESET PICTURE SETTINGS

There are factory presets for picture settings available in the user menus. You can use a preset, change each setting manually.
Select PICTURE.
Game Settings are preset for the opti- mum picture quality at the factory and are not adjustable.
Select Picture Mode.
Select Vivid, Standard, Cinema, Sport, or Game.


Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue.

Select Color Temperature.

MANUAL PICTURE ADJUSTMENT

Adjust the picture appearance to suit your preference and viewing situations.
Select PICTURE.

Select Blacklight, Contrast, Brightness, Sharpness, Color, or Tint.
Make appropriate adjustments.
Return to TV viewing.


By segmenting categories, Expert1 and Expert2 provide more categories which users can set as they see fit, offering the optimal picture quality for users.

Select PICTURE.
Select Picture Mode.
Select Expert1 or Expert2.
Select Expert Control.
Select your desired menu option.
Return to TV viewing.

PICTURE IMPROVEMENT TECHNOLOGY
Fresh Contrast: Optimizes the contrast automatically according to the brightness of the reflection. Fresh Color: Adjusts the color of the reflection automatically to reproduce as close as possible natural colors. Noise Reduction: Removes interference up to the point where it does not damage the original picture. Gamma: High gamma values display whitish images and low gamma values display high contrast images.


Select Fresh Contrast, Fresh Color, Noise Reduction, or Gamma.


Adjusting the contrast and the brightness of the screen using the black level of the screen. This feature is disable in DTV and RGB-PC mode.

screen and set it to High or Low auto- matically.

ADVANCED CONTROL - EYE CARE

Dims extremely bright pictures. This feature is disable in “Picture Mode-Vivid, Cinema”.


Set up the TV for the best picture appearance for viewing movies. When you operate Real Cinema (3:2 Pull-Down Mode or Cinema Correction Mode), the TV will adjust 24 fps video from movies to 30 fps video for display. This feature operates only in TV (Analog TV/CATV, Digital DTV/CADTV), AV1, AV2, Component 480i/1080i, and HDMI 1080i mode.


Select PICTURE.
Select Advanced Control.
Select Real Cinema.


Settings of the selected picture modes return to the default factory settings.



Auto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program.
Select AUDIO.
Select Auto Volume.
Select On or Off.


By differentiating the human sound range from others, it improves the sound quality of voices.
Select AUDIO.
Select Clear Voice.
Select On or Off.
TruSurround XT feature will not work.

Sound Mode lets you enjoy the best sound without any special adjustment as the TV sets the appropriate sound options based on the program content. Standard, Music, Cinema, Sport, and Game are preset for optimum sound quality at the factory and are not adjustable.
1 SOUND Select the sound options: Standard, Music, Cinema, Sport, and Game (your own settings).
Return to TV viewing. 2
I You can also adjust Sound Mode in
the AUDIO menu.


Adjust the sound to suit your taste and room situations.

Select Standard, Music, Cinema, Sport, or Game.
Select Treble or Bass.


Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement produces an immersive sound experience from standard stereo material.



Adjust the left/right sound of speaker to suit your taste and room situations.
Select AUDIO.
Select Balance.
Make appropriate adjustments.


Turn the TV speakers off if using external audio equipment.
Select AUDIO.
Select TV Speaker.
Select On or Off.


Settings of the selected Sound Mode return to the default factory settings.
Select AUDIO.
Select Reset.

For Analog only: This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used if the broadcast is only in Mono.
Each time you press the SAP button, Mono, Stereo, or SAP appear in turn.
Return to TV viewing.
I If other languages available on the digital signal,
select them with the SAP button.

AUDIO LANGUAGE

Other languages may be available if a digital signal is provided by the broadcasting station. This feature operates only in DTV/CADTV mode.



The menus can be shown on the screen in the selected language.
Select OPTION.
Select Language.
Select Menu.
Select your desired language. From this point on, the on-screen menus will be shown in the selected language.

CAPTION MODE
Caption must be provided to help people with hearing loss watch TV.
Select Caption On or Off. 1 cc I When selecting Off, Sub-menus for
Analog, DTV, and Digital Option become disabled.
Caption must be provided to help people with hearing loss watch TV. Select a caption mode for displaying cap- tioning information if provided on a program. Analog caption displays information at any position on the screen and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable. This TV is programmed to memorize the caption/text mode which was last set when you turned the power off. This function is only available when Caption Mode is set On.
Select OPTION.
Select Caption.
The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the pro- gram provided for the hearing impaired.
Select On.
The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provid- ed by the broadcaster. 5


Choose the language you want the DTV/CADTV Captions to appear in. Other Languages can be chosen for digital sources only if they are included on the program. This function in only available when Caption Mode is set On.
Select OPTION.
Select Caption.
Select On.


Customize the DTV/CADTV captions that appear on your screen. This function in only available when Caption Mode is set On.

Select OPTION.

Select On.
Select Custom. 5
Customize the Style, Font, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language.

CLOCK SETTING

The time is set automatically from a digital channel signal. The digital channel signal includes information for the current time provided by the broadcasting station. Set the clock manually if the current time is set incorrectly by the auto clock function.
Select your viewing area time zone. • U.S.A: Eastern, Central, Mountain, Pacific, Alaska, or Hawaii.
Select Auto, On, or Off (depending on whether or not your viewing area observes Daylight Saving time).


If the current time setting is wrong, reset the clock manually.
Select TIME.
Select Clock.
Select Manual.
Set the Year, Month, Date, Hour, or Minutes option. 5


This function operates only if the current time has been set. The Off Time function overrides the On Time function if they are both set to the same time. The TV must be in standby mode for the On Time to work.
Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Weekend, or Sunday. 4

SLEEP TIMER SETTING
The Sleep Time turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off.
I You can also adjust Sleep Timer in the Time menu.


TV will be automatically turned off, in case of no signal for 10 minutes.
TV will be automatically turned off, in case of No Signal for 10 minutes.

Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broad- casting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be done : 1. Set ratings and categories to be blocked. 2. Specify a password 3. Enable the lock
V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to- video movies use the Movie Rating System (MPAA) only.
I TV-MA (Mature audience only)
I TV-PG (Parental guidance suggested)
I TV-Y (All children)
I TV-14 (Parents strongly cautioned)
I TV-Y7 (Children 7 years older)
SET PASSWORD & LOCK SYSTEM

Set up blocking schemes to block specific channels, ratings, and external viewing sources. A password is required to gain access to this menu.



ENTER I When you select On, the Lock System


Choose any 4 digits for your new password. As soon as the 4 digits are entered, re-enter the same 4 digits on the Confirm.


Blocks any channels that you do not want to watch or that you do not want your children to watch.
Block/Unblock Move Page CH Move Previous RETURN Exit MENU

Select a channel to block or unblock. 4

MOVIE & TV RATING

Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.
Select G, PG, PG-13, R, NC-17, X, or Blocking Off. 4
G If you set PG-13: G and PG movies will
be available, PG-13, R, NC-17 and X will be blocked.


Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audi- ences in the TV Rating - sub menu, your children can view those programs.

Select TV Rating-Children.
I Fantasy Violence (applies to TV-Y7)
Select block options. 5


Based on the ratings, blocks certain TV programs that you and your family do not want to view.


This function may become available in the future and will be available only for digital channels. This function operates only when TV has received Region5 Rating data.
(On Screen Display) may differ slightly from what is shown in this manual.

Select desired option and block it. 5




TROUBLESHOOTING
The operation does not work normally.
I Check to see if there is any object between the product and the remote control
causing obstruction. Ensure you are pointing the remote control directly at the TV.
I Ensure that the batteries are installed with correct polarity (+ to +, - to -).
I Ensure that the correct remote operating mode is set: TV, VCR etc.
I Install new batteries.
I Is the sleep timer set?
I Check the power control settings. Power interrupted.
The video function does not work.
I Check whether the product is turned on.
I Try another channel. The problem may be with the broadcast.
No picture &No sound
I Check your antenna direction and/or location.
I Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.
I This is normal, the image is muted during the product startup process. Please
contact your service center, if the picture has not appeared after five minutes.
I Adjust Color in menu option.
I Keep a sufficient distance between the product and the VCR.
I Try another channel. The problem may be with the broadcast.
I Are the video cables installed properly?
I Activate any function to restore the brightness of the picture.
Horizontal/vertical bars
I Check for local interference such as an electrical appliance or power tool.
I Station or cable product experiencing problems, tune to another station.
I Station signal is weak, reorient antenna to receive weaker station.
I Check for sources of possible interference.
I Check antenna (Change the direction of the antenna).
I Check HDMI cable over version 1.3.
The HDMI cables don’t support HDMI version 1.3, it cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
*This feature is not available for all models.

The audio function does not work.
I Press the VOL or VOLUME button.
I Sound muted? Press MUTE button.
I Try another channel. The problem may be with the broadcast.
No output from one
I Adjust Balance in menu option.
I A change in ambient humidity or temperature may result in an unusual noise
when the product is turned on or off and does not indicate a fault with the product.
I Check HDMI cable over version 1.3.
I Check USB cable over version 2.0.
I Use normal MP3 file.
*This feature is not available for all models.
I Adjust resolution, horizontal frequency, or vertical frequency.
I Check the input source.
background & Horizontal Noise &
I Work the Auto configure or adjust clock, phase, or H/V position. (Option)
APPENDIX
I Check the signal cable.
or single color
I Reinstall the PC video card.

Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
I To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
I Please be sure not to use a wet cloth.
CAUTION
G If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.
32LG3DC 32LG3DCH (32LG3DC-UA/32LG3DCH-UA)
MODEL
26.1 x20.0 x 8.9 inches 663.3 x 508.2 x 227.3 mm
31.5 x 23.7 x 9.1 inches 801.8 x 604.2 x 232 mm 31.5 x 21.4 x 4.2 inches 801.8 x 544.4 x 109 mm
Dimensions (Width x Height x Depth)
26.1 x 17.6 x 3.1 inches 663.3 x 449.8 x 80.0 mm
With stand Without stand
22.2 pounds / 10.1 kg 18.9 pounds / 8.6 kg
29.5 pounds / 13.4 kg 26.2 pounds / 11.9 kg
Power requirement Television System Program Coverage External Antenna Impedance
AC100-240V ~(only 32LG3DC)/ 110V 50/60Hz
NTSC-M, VSB, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
Operating Temperature Operating Humidity
32 ~ 104°F (0 ~ 40°C) Less than 80%
Storage Temperature Storage Humidity
I The specifications shown above may be changed without prior notice for quality improvement.

IR CODES
1. How to Connect
I Connect your wired remote control to the Remote Control port on the TV.
Single pulse, modulated with 37.917KHz signal at 455KHz
Tc Carrier frequency
FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3
I Configuration of frame
1st frame
Lead code Low custom code High custom code Data code Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
I Lead code
4.5 ms 9 ms
I Repeat code
0.55 ms
2.25 ms 9 ms
Bit ”0” Bit ”1”
0.56 ms
0.56 ms
1.12 ms
2.24 ms
The waveform is transmitted as long as a key is depressed.

Code Function Note (Hexa)
08 POWER Remote control Button (Power On/Off)
D6 TV Discrete IR Code (TV Input Selection)
0F TV Remote control Button
5A AV1 Discrete IR Code (AV1 Input Selection)
0B INPUT Remote control Button
BF COMPONENT Discrete IR Code
4D PICTURE Remote control Button
(COMPONENTInput Selection)
52 SOUND Remote control Button
D5 RGB Discrete IR Code (RGB Input Selection)
0A SAP Remote control Button
CE HDMI1 Discrete IR Code (HDMI1Input Selection)
79 RATIO Remote control Button
76 Ratio 4:3 Discrete IR Code (Only 4:3 Mode)
10-19 Number Key 0-9 Remote control Button
77 Ratio 16:9 Discrete IR Code (Only 16:9 Mode)
4C - (Dash) Remote control Button
AF Ratio Zoom Discrete IR Code (Only Zoom1 Mode)
1A FLASHBK Remote control Button
C4 POWER ON Discrete IR Code (Only Power On)
02 VOL + Remote control Button
C5 POWER OFF Discrete IR Code (Only Power Off)
03 VOL - Remote control Button
00 CH + Remote control Button
01 CH - Remote control Button
0E TIMER Remote control Button
39 CC Remote control Button
09 MUTE Remote control Button
CB ADJUST Remote control Button
43 MENU Remote control Button
5B RETURN Remote control Button
40 Remote control Button
41 Remote control Button
07 Remote control Button
06 Remote control Button
44 ENTER Remote control Button


Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.