
User's Guide
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. All other trademarks are the property of their respective owners.
© 2008 Lexmark International, Inc. All rights reserved. 740 West New Circle Road Lexington, Kentucky 40550




Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Use care when you replace a lithium battery.
Use only the power cord provided with this product or the manufacturer's authorized replacement.
Use only the telecommunications (RJ-11) cord provided with this product or a 26 AWG or larger replacement when connecting this product to the public switched telephone network.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If the power cord is misused, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of misuse. Remove the power cord from the electrical outlet before inspecting it.
Safety information

Refer service or repairs, other than those described in the user documentation, to a professional service person.
CAUTION—TIPPING HAZARD: Floor-mounted configurations require additional furniture for stability. You must use either a printer stand or printer base if you are using a high-capacity input tray, a duplex unit and an input option, or more than one input option. If you purchased a multifunction printer (MFP) that scans, copies, and faxes, you may need additional furniture. For more information, see www.lexmark.com/multifunctionprinters.
SAVE THESE INSTRUCTIONS.
Safety information

Finding information about the printer

The Setup information gives you instructions for setting up the printer. Follow the set of instructions for local, network, or wireless, depending on what you need.
You can find the Setup information on the side of the printer box or on the Lexmark Web site at www.lexmark.com.

The Help gives you instructions for using the software. While in any Lexmark software program, click Help,
Description Where to find (North America) Where to find (rest of world)
Telephone support Call us at
Telephone numbers and support hours vary by country or region. Visit our Web site at www.lexmark.com. Select a country or region, and then select the Customer Support link.
Learning about the printer

Description Where to find (North America) Where to find (rest of world)
E-mail support For e-mail support, visit our Web site: www.lexmark.com.
E-mail support varies by country or region, and may not be available in some instances. Visit our Web site at www.lexmark.com. Select a country or region, and then select the Customer Support link.
1 Click SUPPORT. 2 Click Technical Support. 3 Select your printer type. 4 Select your printer model. 5 From the Support Tools section, click e-Mail Support. 6 Complete the form, and then click Submit Request.

Learning about the printer

When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options, leave enough room for them also. It is important to:

1 Right Side 20 cm (8 in.)
2 Left Side 31 cm (12 in.)
3 Front 51 cm (20 in.)
4 Rear 20 cm (8 in.)
5 Top 31 cm (12 in.)
The scanner provides copy, fax, and scan-to-network capability for large workgroups. You can:
Learning about the printer


Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings or lightweight carbonless forms).
You can use the ADF or the scanner glass to scan documents.
The Automatic Document Feeder (ADF) can scan multiple pages, including duplex pages. When using the ADF:
The scanner glass can be used to scan or copy single pages or book pages. When using the scanner glass:
Learning about the printer


1 Display View scanning, copying, faxing, and printing options as well as status and error messages.
Enter numbers or symbols on the display.
6 MNO 5 JKL 4 GHI
9 WXYZ 8 TUV 7 PQRS
4 Back In the Copy menu, press to delete the right-most digit of the value in the Copy Count. The default value of 1 appears if the entire number is deleted by pressing numerous times.
In the Fax Destination List, press to delete the right-most digit of a number entered manually. You can also press to delete an entire shortcut entry. Once an entire line is deleted, another press of causes the cursor to move up one line.
In the E-mail Destination List, press to delete the character to the left of the cursor. If the character is in a shortcut, then the shortcut is deleted.
5 Home Press to return to the home screen.
Learning about the printer
Item Description · 2 Keypad · # 0 *

7 Indicator light Indicates the printer status:
8 Stop Stops all printer activity A list of options is offered once Stopped appears on the display.
After the printer is turned on and a short warm-up period occurs, the display shows the following basic screen which is referred to as the home screen. Use the home screen buttons to initiate an action such as copying, faxing, or scanning; to open the menu screen; or to respond to messages.

Ready Touch any button to begin.
3 4 5 6 7
1 Copy Opens the Copy menus
2 E-mail Opens the E-mail menus
3 Menus Opens the menus. These menus are available only when the printer is in the Ready state.
4 FTP Opens the File Transfer Protocol (FTP) menus
Learning about the printer
Item Description · Display item Description

6 Status/Supplies Appears on the display whenever the printer status includes a message requiring intervention. Touch it to access the messages screen for more information on the message, including how to clear it.
7 Tips All menus have a Tips button. Tips is a context-sensitive Help feature within the display touch screens.
8 Fax Opens the Fax menus
Other buttons that may appear on the home screen:
Release Held Faxes If this button is shown, then there are held faxes with a scheduled hold time previously set. To access the list of held faxes, touch this button.
Search Held Jobs Searches on any of the following items and returns search results:
Held Jobs Opens a screen containing all the held jobs
Lock Device This button appears on the screen when the printer is unlocked and Device Lockout Personal Identification Number (PIN) has been set. Touching this button opens a PIN entry screen. Entering the correct PIN locks the printer control panel (touch screen and hard buttons).
Unlock Device This button appears on the screen when the printer is locked. The printer control panel buttons and shortcuts cannot be used while it appears. Touching this button opens a PIN entry screen. Entering the correct PIN unlocks the printer control panel (touch screen and hard buttons).
Learning about the printer
Display item Description · Display item Function

Cancel Jobs Opens the Cancel Jobs screen. The Cancel Jobs screen shows three headings: Print, Fax, and Network. The following items are available under the Print, Fax, and Network headings:
Each heading has a list of jobs shown in a column under it which can show only three jobs per screen. Each job appears as a button which you can touch to access information about the job. If more than three jobs exist in a column, then an arrow appears enabling you to scroll through the jobs.

Returns to the home screen
Opens a drop-down list
Learning about the printer

Scrolls to another value in decreasing order
Scrolls to another value in increasing order
Saves a value as the new user default setting
Navigates back to the previous screen
Moves down to the next screen
Moves up to the next screen
This is an unselected radio button. The radio button is gray to show it is unselected.
Learning about the printer

This is a selected radio button. The radio button is blue to show it is selected.
Opens the Cancel Jobs screen. The Cancel Jobs screen shows three headings: Print, Fax, and Network. The following items are available under the Print, Fax, and Network headings:
Each heading has a list of jobs shown in a column under it which can show only three jobs per screen. Each job appears as a button which you can touch to access information about the job. If more than three jobs exist in a column, then an arrow appears enabling you to scroll through the jobs.
Touch this button when more changes need to be made for a job or after clearing a paper jam.
Selects a menu or menu item
Learning about the printer

Menu trail line:
A Menu trail line is located at the top of each menu screen. This feature acts as a trail, showing the path taken to arrive at the current menu. It gives the exact location within the menus.
Menus Settings Copy Settings Number of Copies
Touch any of the underlined words to return to that menu or menu item. The Number of Copies is not underlined since this is the current screen. If you touch an underlined word on the Number of Copies screen before the Number of Copies is set and saved, then the selection is not saved, and it does not become the user default setting.
If an attendance message occurs which closes a function, such as copy or fax, then a solid red dot appears over the function button on the home screen. This indicates that an attendance message exists.
Learning about the printer
Feature Description · Attendance message alert

Installing internal options
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
You can customize your printer connectivity and memory capacity by adding optional cards. The instructions in this section explain how to install the available cards; you can also use them to locate a card for removal.
Additional printer setup

CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Open the system board door.

2 Loosen the screw(s) on the system board cover.

Additional printer setup

3 Remove the system board cover.

4 Use the illustration below to locate the appropriate connector.


3 Lexmark Internal Solutions Port or printer hard disk connector
Additional printer setup

CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
An optional memory card can be purchased separately and attached to the system board. To install the memory card:
1 Access the system board.

2 Unpack the memory card.
3 Open the memory card connector latches.
4 Align the notches on the memory card with the ridges on the connector.

1 Notches · 2 Ridges · Additional printer setup

5 Push the memory card straight into the connector until it snaps into place.
6 Replace the system board cover and close the system board door.

The system board has two connections for an optional flash memory or firmware card. Only one of each may be installed, but the connectors are interchangeable.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the system board.

2 Unpack the card.
Additional printer setup

3 Holding the card by its sides, align the plastic pins on the card with the holes on the system board.

4 Push the card firmly into place.

1 Plastic pins · 2 Metal pins · Additional printer setup

5 Replace the system board cover and close the system board door.

The system board supports one optional Lexmark Internal Solutions Port (ISP). Install an ISP for additional connectivity options.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the system board.

2 Unpack the ISP and plastic tee.
Additional printer setup

3 Locate the appropriate connector on the system board.

hard disk. To unplug the cable, squeeze the paddle at the plug of the interface cable to disengage the latch before pulling the cable out.

b Remove the screws holding the printer hard disk in place.

Additional printer setup

c Remove the printer hard disk by pulling it upward to unseat the standoffs.

d Remove the thumbscrews that attach the printer hard disk mounting bracket to the printer hard disk, and
then remove the bracket. Set the printer hard disk aside.

Additional printer setup

4 Remove the metal cover from the ISP opening.

5 Align the posts of the plastic tee to the holes in the system board, and then press downward until the tee snaps into place. Be sure each post of the tee has latched completely, and that the tee is seated firmly onto the system board.

Additional printer setup

6 Install the ISP onto the plastic tee. Angle the ISP over the plastic tee, and then approach the plastic tee so that any overhanging connectors will pass through the ISP opening in the system board cage.

7 Lower the ISP toward the plastic tee until the ISP is seated between the guides of the plastic tee.

8 Insert the long thumbscrew and turn it clockwise enough to hold the ISP in place, but do not tighten the thumbscrew at this time.

Additional printer setup

9 Attach the two provided screws to secure the ISP mounting bracket to the system board cage.

10 Tighten the long thumbscrew.
11 Insert the plug of the ISP interface cable into the receptacle of the system board.

12 If a printer hard disk was previously installed, then attach the printer hard disk to the ISP. For more information, see “Installing a printer hard disk” on page 38.
Additional printer setup

13 Replace the system board cover and close the system board door.

The optional printer hard disk can be installed with or without a Lexmark Internal Solutions Port (ISP).
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the system board.

2 Unpack the printer hard disk.
Additional printer setup

3 Locate the appropriate connector on the system board.

To install a printer hard disk onto the ISP:
a Using a flathead screwdriver to loosen the screws, remove the thumbscrews that attach the printer hard disk
mounting bracket to the printer hard disk, and then remove the bracket.

b Align the standoffs of the printer hard disk with the holes in the ISP, and then press downward on the printer
hard disk until the standoffs have seated into place.

Additional printer setup

c Insert the plug of the printer hard disk interface cable into the receptacle of the ISP.

To install a printer hard disk directly onto the system board:
a Align the standoffs of the printer hard disk with the holes in the system board, and then press downward on
the printer hard disk until the standoffs have seated into place.

Additional printer setup

b Attach the two provided screws to secure the printer hard disk mounting bracket.

c Insert the plug of the printer hard disk interface cable into the receptacle of the system board.

4 Replace the system board cover and close the system board door.

Additional printer setup

CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the system board.

2 Unpack the fax card.
3 Remove the metal cover from the fax card opening.

Additional printer setup

4 Insert the fax card and attach the two provided screws to secure the fax card mounting bracket.


Additional printer setup

5 Insert the plug of the fax card interface cable into the receptacle of the system board.

6 Replace the system board cover and close the system board door.

Connect the printer to the computer using a USB cable or Ethernet cable.
Be sure to match the following:
Additional printer setup


Once all hardware and software options are installed and the printer is turned on, verify that the printer is set up correctly by printing the following: .
Print a menu settings page to review the current menu settings and to verify printer options are installed correctly.
Note: If you have not made any menu item settings changes yet, then the menu settings page lists all the factory default settings. Once you select and save other settings from the menus, they replace the factory default settings as user default settings. A user default setting remains in effect until you access the menu again, choose another value, and save it. To restore the factory default settings, see “Restoring the factory default settings” on page 264.
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch
1 USB port · 2 Ethernet port · Additional printer setup

3 Touch Reports.
4 Touch Menu Settings Page.
The menu settings page prints and the printer returns to the home screen.
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch
3 Touch Reports.
4 Touch Network Setup Page.
The network setup page prints and the printer returns to the home screen.
5 Check the first section on the network setup page, and confirm that Status is “Connected.”
If Status is “Not Connected,” the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and then print another network setup page.
A printer driver is software that lets the computer communicate with the printer. The printer software is typically installed during the initial printer setup. If you need to install the software after setup, follow these instructions:
1 Close all open software programs.
2 Insert the Software and Documentation CD.
3 From the main installation dialog, click Install.
4 Follow the instructions on the screen.
1 Close all open software applications.
2 Insert the Software and Documentation CD.
3 From the Finder desktop, double-click the printer CD icon that automatically appears.
4 Double-click the Install icon.
5 Follow the instructions on the screen.
Additional printer setup

1 Go to the Lexmark Web site at www.lexmark.com.
2 From the Drivers & Downloads menu, click Driver Finder.
3 Select your printer, and then select your operating system.
4 Download the driver and install the printer software.
Once the printer software and any options are installed, it may be necessary to manually add the options in the printer driver to make them available for print jobs.
1 Do one of the following:
. b Click Control Panel.
c Click Hardware and Sound. d Click Printers.
a Click Start. b Click Printers and Faxes.
a Click Start. b Click Settings Printers.
2 Select the printer.
3 Right-click the printer, and then select Properties.
4 Click the Install Options tab.
5 Under Available Options, add any installed hardware options.
6 Click Apply.
In Mac OS X version 10.5
1 From the Apple menu, choose System Preferences.
2 Click Print & Fax.
3 Select the printer, and then click Options & Supplies.
a Click · Additional printer setup

4 Click Driver, and then add any installed hardware options.
5 Click OK.
1 From the Go menu, choose Applications.
2 Double-click Utilities, and then double-click Print Center or Printer Setup Utility.
3 Select the printer, and then from the Printers menu, choose Show Info.
4 From the pop-up menu, choose Installable Options.
5 Add any installed hardware options, and then click Apply Changes.
Information you will need to set up the printer on a wireless network
Some ad hoc networks will also require the auto setting. Check with your system support person if you are not sure which channel to select. • Security Method—There are three basic options for Security Method: – WEP key
If your network uses more than one WEP key, enter up to four in the provided spaces. Select the key currently in use on the network by selecting the Default WEP Transmit Key. or – WPA or WPA2 passphrase
WPA includes encryption as an additional layer of security. The choices are AES or TKIP. Encryption must be set for the same type on the router and on the printer, or the printer will not be able to communicate on the network. – No security
If your wireless network does not use any type of security, then you will not have any security information.
If you are installing the printer on an 802.1X network using the Advanced method, then you may need the following:
Additional printer setup

Before you install the printer on a wireless network, make sure that:
1 Connect the power cable, and then turn the printer on.


Make sure the printer and computer are fully on and ready.
Do not connect the USB cable until instructed to do so on the screen
2 Insert the Software and Documentation CD.
3 Click Install.
4 Click Agree.
5 Click Suggested.
Additional printer setup

6 Click Wireless Network Attach.
7 Connect the cables in the following order: a Temporarily connect a USB cable between the computer on the wireless network and the printer.

8 Follow the on-screen instructions to complete the software installation.
9 To allow other computers on the wireless network to use the wireless printer, follow steps 2 through 6 and step 8 for each computer.
1 Locate the printer MAC address on the sheet that came with the printer. Write the last six digits of the MAC address in the space provided below:
2 If your printer has faxing capabilities, then connect the telephone cable.
Additional printer setup

3 Connect the power cable, and then turn the power on.


1 Access the AirPort options.
a From the Apple menu, choose System Preferences. b Click Network.
c Click AirPort.
a From the Go menu, choose Applications. b Double-click Internet Connect.
c From the toolbar, click AirPort.
2 From the Network pop-up menu, select print server xxxxxx, where the x’s are the last six digits of the MAC address located on the MAC address sheet.
3 Open the Safari browser.
4 From the Bookmarks drop-down menu, select Show.
5 Under Collections, select Bonjour or Rendevous, and then double-click the printer name.
6 From the main page of the Embedded Web Server, navigate to the page where the wireless settings information is stored.
1 Type the name of your network (SSID) in the appropriate field.
2 Select Infrastructure as your Network Mode if you are using a wireless router.
Additional printer setup

3 Select the type of security you use to protect your wireless network.
4 Enter the security information necessary for the printer to join your wireless network.
5 Click Submit.
6 Open the AirPort application on your computer:
a From the Apple menu, choose System Preferences. b Click Network.
c Click AirPort.
a From the Go menu, choose Applications. b Double-click Internet Connect.
c From the toolbar, click AirPort.
7 From the Network pop-up menu, select your wireless network.
To print to a network printer, each Macintosh user must install a custom PostScript Printer Description (PPD) file and create a printer in the Print Center or Printer Setup Utility.
1 Install a PPD file on the computer: a Insert the Software and Documentation CD in the CD or DVD drive. b Double-click the installer package for the printer.
c From the Welcome screen, click Continue. d Click Continue again after viewing the Readme file. e Click Continue after viewing the license agreement, and then click Agree to accept the terms of the
agreement. f Select a Destination, and then click Continue. g From the Easy Install screen, click Install. h Type the user password, and then click OK.
All necessary software is installed on the computer. i Click Close when installation is complete.
1 From the Apple menu, choose System Preferences. 2 Click Print & Fax. 3 Click +. 4 Select the printer from the list. 5 Click Add.
Additional printer setup

1 From the Go menu, choose Applications. 2 Double-click Utilities. 3 Locate and double-click Printer Setup Utility or Print Center. 4 From the Printer List, choose Add. 5 Select the printer from the list. 6 Click Add. b For AppleTalk printing:
1 From the Apple menu, choose System Preferences. 2 Click Print & Fax. 3 Click +. 4 Click AppleTalk. 5 Select the printer from the list. 6 Click Add.
1 From the Go menu, choose Applications. 2 Double-click Utilities. 3 Locate and double-click Print Center or Printer Setup Utility. 4 From the Printer List, choose Add. 5 Choose the Default Browser tab. 6 Click More Printers. 7 From the first pop-up menu, choose AppleTalk. 8 From the second pop-up menu, select Local AppleTalk zone. 9 Select the printer from the list. 10 Click Add.
Use the following instructions to install the printer on a wired network. These instructions apply to Ethernet and fiber optic network connections.
Before you install the printer on a wired network, make sure that:
1 Insert the Software and Documentation CD.
Wait for the Welcome screen to appear.
If the CD does not launch after a minute, then do one of the following:
Additional printer setup

. b In the Start Search box, type D:\setup.exe, where D is the letter of your CD or DVD drive.
a Click Start. b Click Run.
c Type D:\setup.exe, where D is the letter of your CD or DVD drive.
2 Click Install Printer and Software.
3 Click Agree to agree to the License Agreement.
4 Select Suggested, and then click Next.
5 Select Wired Network Attach, and then click Next.
6 Select the printer manufacturer from the list.
7 Select the printer model from the list, and then click Next.
8 Select the printer from the list of printers discovered on the network, and then click Finish.
9 Follow the on-screen instructions to complete the installation.
1 Allow the network DHCP server to assign an IP address to the printer.
2 Print the network setup page from the printer. For information on printing a network setup page, see “Printing a network setup page” on page 46.
3 Locate the printer IP address in the TCP/IP section of the network setup page. You will need the IP address if you are configuring access for computers on a different subnet than the printer.
4 Install the drivers and add the printer. a Install a PPD file on the computer:
1 Insert the Software and Documentation CD in the CD or DVD drive. 2 Double-click the installer package for the printer. 3 From the Welcome screen, click Continue. 4 Click Continue again after viewing the Readme file. 5 Click Continue after viewing the license agreement, and then click Agree to accept the terms of the agreement. 6 Select a Destination, and then click Continue. 7 From the Easy Install screen, click Install.
a Click · Additional printer setup

8 Type the user password, and then click OK. All the necessary software is installed on the computer. 9 Click Close when installation is complete. b Add the printer:
1 From the Apple menu, choose System Preferences. 2 Click Print & Fax. 3 Click +. 4 Select the printer from the list. 5 Click Add.
1 From the Go menu, choose Applications. 2 Double-click Utilities. 3 Double-click Printer Setup Utility or Print Center. 4 From the Printer List, click Add. 5 Select the printer from the list. 6 Click Add. • For AppleTalk printing:
1 From the Apple menu, choose System Preferences. 2 Click Print & Fax. 3 Click +. 4 Click AppleTalk. 5 Select the printer from the list. 6 Click Add.
1 From the Go menu, choose Applications. 2 Double-click Utilities. 3 Double-click Print Center or Printer Setup Utility. 4 From the Printer List, click Add. 5 Choose the Default Browser tab. 6 Click More Printers. 7 From the first pop-up menu, choose AppleTalk. 8 From the second pop-up menu, select Local AppleTalk zone. 9 Select the printer from the list. 10 Click Add.
Additional printer setup

When a new network Lexmark Internal Solutions Port (ISP) is installed in the printer, the printer configurations on computers that access the printer must be updated because the printer will be assigned a new IP address. All computers that access the printer must be updated with this new IP address in order to print to it over the network.
1 Print a network setup page and make a note of the new IP address.
2 Do one of the following:
. b Click Control Panel.
c Under Hardware and Sound, click Printer.
a Click Start. b Click Printers and Faxes.
a Click Start. b Click Settings Printers.
3 Locate the printer that has changed.
4 Right-click the printer.
5 Click Properties.
6 Click the Ports tab.
7 Locate the port in the list, and then select it.
8 Click Configure Port.
a Click · Additional printer setup

9 Type the new IP address in the “Printer Name or IP Address” field. You can find the new IP address on the network setup page you printed in step 1.
10 Click OK, and then click Close.
1 Print a network setup page and make a note of the new IP address.
2 Locate the printer IP address in the TCP/IP section of the network setup page. You will need the IP address if you are configuring access for computers on a different subnet than the printer.
a From the Apple menu, choose System Preferences. b Click Print & Fax.
c Click +. d Select the printer from the list. e Click Add.
a From the Go menu, choose Applications. b Double-click Utilities.
c Double-click Printer Setup Utility or Print Center. d From the Printer List, click Add. e Select the printer from the list.
f Click Add. • For AppleTalk printing:
a From the Apple menu, choose System Preferences. b Click Print & Fax.
c Click +. d Click AppleTalk. e Select the printer from the list.
f Click Add.
a From the Go menu, choose Applications. b Double-click Utilities.
c Double-click Print Center or Printer Setup Utility. d From the Printer List, click Add. e Choose the Default Browser tab.
f Click More Printers. g From the first pop-up menu, choose AppleTalk.
Additional printer setup

h From the second pop-up menu, select Local AppleTalk zone.
i Select the printer from the list. j Click Add.
In serial printing, data is transferred one bit at a time. Although serial printing is usually slower than parallel printing, it is the preferred option when there is a great deal of distance between the printer and computer or when an interface with a better transfer rate is not available.
After installing the serial port, you will need to configure the printer and the computer so they can communicate. Make sure you have connected the serial cable to the serial port on your printer.
1 Set the parameters in the printer: a From the printer control panel, navigate to the menu with port settings. b Locate the submenu with serial port settings.
c Make any necessary changes to the serial settings. d Save the new settings. e Print a menu settings page.
2 Install the printer driver: a Insert the Software and Documentation CD. It launches automatically.
If the CD does not launch automatically, do one of the following:
. 2 In the Start Search box, type D:\setup.exe, where D is the letter of your CD or DVD drive.
1 Click Start. 2 Click Run. 3 Type D:\setup.exe, where D is the letter of your CD or DVD drive.
b Click Install Printer and Software.
c Click Agree to accept the Printer Software License Agreement. d Click Custom. e Make sure Select Components is selected, and then click Next.
f Make sure Local is selected, and then click Next. g Select the manufacturer of the printer from the menu. h Select the printer model from the menu, and then click Add Printer.
i Click the + beside the printer model under Select Components. j Make sure the correct port is available under Select Components. This is the port where the serial cable attaches to the computer. If the correct port is not available, select the port under the Select Port menu, and then click Add Port.
1 Click · Additional printer setup

k Make any configuration changes necessary in the Add a New Port window. Click Add Port to finish adding
the port. l Make sure the box next to the selected printer model is checked. m Select any other optional software you want to install, and then click Next.
n Click Finish to complete the printer software installation.
3 Set the COM port parameters:
After the printer driver is installed, you must set the serial parameters in the communications (COM) port assigned to the printer driver.
The serial parameters in the COM port must match the serial parameters you set in the printer.
a Open the Device Manager. Do one of the following:
. 2 Click Control Panel. 3 Click System and Maintenance. 4 Click System. 5 Click Device Manager.
1 Click Start. 2 Click Control Panel. 3 Click Performance and Maintenance. 4 Click System. 5 From the Hardware tab, click Device Manager.
1 Click Start. 2 Click Settings Control Panel. 3 Click System. 4 From the Hardware tab, click Device Manager. b Click + to expand the list of available ports.
c Select the communications port where you attached the serial cable to your computer (example: COM1). d Click Properties. e On the Port Settings tab, set the serial parameters to the same serial parameters in the printer.
Look for the printer settings under the serial heading on the Menu Settings page you printed earlier. f Click OK, and then close all the windows. g Print a test page to verify printer installation. When a test page prints successfully, printer setup is complete.
1 Click · Additional printer setup

The following connection methods may not be applicable in all countries or regions.
You can connect the printer with equipment such as a telephone, an answering machine, or a computer modem.
Note: The printer is an analog device that works best when directly connected to the wall jack. Other devices (such as a telephone or answering machine) can be successfully attached to pass through the printer, as described in the setup steps. If you want a digital connection such as ISDN, DSL, or ADSL, a third-party device (such as a DSL filter) is required.
You do not need to attach the printer to a computer, but you do need to connect it to a telephone line to send and receive faxes.
You can connect the printer to other equipment. See the following table to determine the best way to set up the printer.
Send and receive faxes without using a computer.
Receive both incoming voice messages and faxes.
Send faxes using the computer or the printer.
Equipment Benefits · Additional printer setup

To connect your printer to an answering machine, telephone, or other telecommunications equipment, use the telephone line adapter included in the box with the printer in some countries or regions.
1 Connect the adapter to the telephone cord that came with the printer.
2 Connect the telephone line of your chosen telecommunications equipment to the left outlet of the adapter.
If your telecommunications equipment uses a US-style (RJ11) telephone line, follow these steps to connect the equipment:
1 Remove the plug from the EXT port on the back of the printer.

Country/region · Additional printer setup


2 Connect your telecommunications equipment directly to the EXT port on the back of the printer.

Country/region · Additional printer setup

To connect a telephone, an answering machine, or other telecommunications equipment to the printer:
1 Remove the plug from the back of the printer.

2 Connect your telecommunications equipment directly to the EXT port on the back of the printer.
Country/region · Additional printer setup

There is a plug installed in the EXT port of the printer. This plug is necessary for the proper functioning of the printer.
Connect the printer directly to a telephone wall jack to send and receive faxes without using a computer.
1 Make sure you have a telephone cord (provided with the product) and a telephone wall jack.
2 Connect one end of the telephone cord into the LINE port of the printer.

3 Connect the other end of the telephone cord into the N slot of an active telephone wall jack.

Additional printer setup

4 If you would like to use the same line for both fax and telephone communication, connect a second telephone line (not provided) between the telephone and the F slot of an active telephone wall jack.

5 If you would like to use the same line for recording messages on your answering machine, connect a second telephone line (not provided) between the answering machine and the other N slot of the telephone wall jack.

Connect a telephone to the printer to use the fax line as a normal telephone line. Then set up the printer wherever your telephone is located to make copies or to send and receive faxes without using a computer.
Additional printer setup

2 Connect one telephone cord to the LINE port of the printer, and then plug it into an active telephone wall jack.

3 Remove the protective plug from the EXT port of the printer.
4 Connect the other telephone cord to a telephone, and then plug it into the EXT port of the printer.

Connect an answering machine to the printer to receive both incoming voice messages and faxes.
Additional printer setup

2 Connect one telephone cord into the LINE port of the printer, and then plug it into an active telephone wall jack.

3 Remove the protective plug from the EXT port of the printer.
4 Connect a second telephone cord from the telephone to the answering machine.

Additional printer setup


5 Connect a third telephone cord from the answering machine to the EXT port of the printer.
Connect the printer to a computer with a modem to send faxes from the software program.
2 Connect a telephone cord into the LINE port of the printer, and then plug it into an active telephone wall jack.

3 Remove the protective plug from the EXT port of the printer.
Additional printer setup

4 Connect a second telephone cord from the telephone to the computer modem.

5 Connect a third telephone cord from the computer modem to the EXT port of the printer.

To have the designated fax name and fax number printed on outgoing faxes:
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Click Fax Settings.
4 Click Analog Fax Setup.
5 Click inside the Station Name box, and then enter the name to be printed on all outgoing faxes.
6 Click inside the Station Number box, and then enter the printer fax number.
7 Click Submit.
Additional printer setup

You can set the date and time so that they are printed on every fax you send. If there is a power failure, then you may have to reset the date and time. To set the date and time:
1 Type the printer IP address into the address field of your Web browser.
2 Click Links & Index.
3 Click Set Date and Time.
4 Click inside the Manually Set Date & Time box, and then enter the current date and time.
5 Click Submit.
The printer can be set to automatically adjust for Daylight Saving Time (DST):
1 Type the printer IP address into the address field of your Web browser.
2 Click Links & Index.
3 Click Set Date and Time.
4 Select Automatically Observe DST.
5 Click Submit.
Additional printer setup

This section explains how to load the 250-, 500-, and 2000-sheet trays, and the multipurpose feeder. It also includes information about paper orientation, setting the Paper Size and Paper Type, and linking and unlinking trays.
The Paper Size setting is determined by the position of the paper guides in the tray for all trays except the multipurpose feeder. The Paper Size setting for the multipurpose feeder must be set manually. The factory default Paper Type setting is Plain Paper. The Paper Type setting must be set manually for all trays that do not contain plain paper.
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch
3 Touch Paper Menu.
4 Touch Paper Size/Type.
5 Touch the arrows for the desired tray until the correct size or type setting appears.
6 Touch Submit.
to return to the home screen.
The Universal Paper Size is a user-defined setting that lets you print on paper sizes that are not preset in the printer menus. Set the Paper Size for the specified tray to Universal when the size you want is not available from the Paper Size menu. Then, specify all of the following Universal size settings for your paper:
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch
3 Touch Paper Menu.
4 Touch the down arrow until Universal Setup appears, and then touch Universal Setup.
5 Touch the left or right arrow to select the desired unit of measure.
6 Touch Portrait Width or Portrait Height.
7 Touch the arrows to select the desired width or height.
Loading paper and specialty media
7 Touch

8 Touch Submit to save your selection.
Submitting Selection appears, followed by the Paper menu.
to return to the home screen.
Although the 250-sheet tray and the 550-sheet tray are different in appearance, they require the same process for loading paper. Use these instructions to load paper in either tray:
1 Pull the tray out.

2 Squeeze the width guide tab inward as shown, and move the width guide to the correct position for the paper size being loaded.

Loading paper and specialty media
9 Touch

3 Unlock the length guide, squeeze the length guide tab inward as shown, and slide the guide to the correct position for the paper size being loaded.

4 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

Loading paper and specialty media


Without an optional StapleSmart II Finisher With an optional StapleSmart II Finisher

6 If necessary, adjust the paper guides to lightly touch the sides of the stack, and lock the length guide for the paper sizes indicated on the tray.
Loading paper and specialty media

7 Insert the tray.

8 If a different type of paper was loaded than the type previously loaded in the tray, then change the Paper Type setting for the tray from the printer control panel.
1 Pull the tray out.
2 Pull up and slide the width guide to the correct position for the paper size being loaded.

Loading paper and specialty media

3 Unlock the length guide.

4 Push the length guide release latch to raise the length guide, slide the guide to the correct position for the paper size being loaded, and then lock the guide.

Loading paper and specialty media

5 Flex the sheets back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.


Without an optional StapleSmart II Finisher With an optional StapleSmart II Finisher
Loading paper and specialty media


Without an optional StapleSmart II Finisher With an optional StapleSmart II Finisher

7 Insert the tray.
Loading paper and specialty media

1 Pull down the multipurpose feeder door.

2 Pull out the extension until it is fully extended.

3 Slide the width guide to the far right.

Loading paper and specialty media

4 Flex the sheets of paper or specialty media back and forth to loosen them, and then fan them. Do not fold or crease them. Straighten the edges on a level surface.

* Avoid touching the print side of transparencies. Be careful not to scratch them.
5 Load the paper or specialty media. Slide the stack gently into the multipurpose feeder until it comes to a stop.

Without an optional StapleSmart Finisher With an optional StapleSmart Finisher
Loading paper and specialty media


Without an optional StapleSmart Finisher With an optional StapleSmart Finisher
6 Adjust the width guide to lightly touch the edge of the paper stack. Make sure the paper fits loosely in the multipurpose feeder, lies flat, and is not bent or wrinkled.
7 From the printer control panel, set the Paper Size and Paper Type.
Loading paper and specialty media

2 Lift the envelope weight back toward the printer.

3 Slide the width guide to the right.

4 Prepare the envelopes for loading.
Flex the envelopes back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the stack of envelopes flap side down.
Loading paper and specialty media


6 Adjust the width guide to lightly touch the edge of the paper stack.
7 Lower the envelope weight to touch the paper stack.
8 From the printer control panel, set the Paper Size and Paper Type.
Tray linking is useful for large print jobs or multiple copies. When one linked tray is empty, paper feeds from the next linked tray. When the Paper Size and Paper Type settings are the same for any trays, the trays are automatically linked.
The printer automatically senses the Paper Size setting according to the position of the paper guides in each tray except the multipurpose feeder. The printer can sense A4, A5, JIS B5, Letter, Legal, Executive, and Universal paper sizes. The multipurpose feeder and trays using other paper sizes can be linked manually using the Paper Size menu available from the Paper Size/Type menu.
The Paper Type setting must be set for all trays from the Paper Type menu available from the Paper Size/Type menu.
Unlinked trays have settings that are not the same as the settings of any other tray.
To unlink a tray, change the following tray settings so that they do not match the settings of any other tray:
Paper Type names describe the paper characteristics. If the name that best describes your paper is used by linked trays, assign a different Paper Type name to the tray, such as Custom Type , or define your own custom name. • Paper Size (for example: letter, A4, statement)
Load a different paper size to change the Paper Size setting for a tray automatically. Paper Size settings for the multipurpose feeder are not automatic; they must be set manually from the Paper Size menu.
Loading paper and specialty media

Assign a custom paper type name to a tray when linking or unlinking the tray.
1 Make sure the printer is on and Ready appears.
2 From the home screen, touch
3 Touch Paper Menu.
4 Touch Paper Size/Type.
5 Touch the paper type arrows for the desired tray until the correct custom type appears.
6 Touch the tray number or MP Feeder Type.
7 Touch Submit.
You can use the Embedded Web Server or MarkVisionTM to define a name other than Custom Type for each of the custom paper types that are loaded. When a Custom Type name is changed, the menus display the new name instead of Custom Type .
To change a Custom Type name from the Embedded Web Server:
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Under Default Settings, click Paper Menu.
4 Click Custom Names.
5 Type a name for the paper type in a Custom Name box.
6 Click Submit.
7 Click Custom Types.
Custom Types appears, followed by your custom name.
8 Select a Paper Type setting from the list next to your custom name.
9 Click Submit.
Loading paper and specialty media

Paper guidelines
Selecting the correct paper or specialty media reduces printing problems. For the best print quality, try a sample of the paper or specialty media before buying large quantities.
The following paper characteristics affect print quality and reliability. Consider these characteristics when evaluating new paper stock.
The printer can automatically feed paper weights from 60–176 g/m2 (16–47 lb bond) grain long. Paper lighter than 60 g/m2 (16 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 75 g/m2 (20 lb bond) grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 in.), we recommend 90 g/m2 (24 lb) or heavier paper.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, then toner cannot fuse to it properly. If paper is too smooth, then it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; smoothness between 150 and 250 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Condition paper before printing by storing it in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
Paper and specialty media guidelines

For 60–176 g/m2 (16–47 lb bond) paper, grain long paper is recommended. For paper heavier than 176 g/m2, grain short is recommended.
Most high-quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton can negatively affect paper handling.
For detailed information on paper with recycled fiber content, see “Using recycled paper and other office papers” on page 87.
The following paper types are not recommended for use with the printer:
Using appropriate paper prevents jams and helps ensure trouble-free printing.
To help avoid jams and poor print quality:
Use these guidelines when selecting preprinted forms and letterhead:
Paper and specialty media guidelines

Use papers printed with heat-resistant inks designed for use in xerographic copiers. The ink must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions. Use inks that are not affected by the resin in toner. Inks that are oxidation-set or oil-based generally meet these requirements; latex inks might not. When in doubt, contact the paper supplier.
Preprinted papers such as letterhead must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser (electrophotographic) printers. In 1998, Lexmark presented to the US government a study demonstrating that recycled paper produced by major mills in the US fed as well as non-recycled paper. However, no blanket statement can be made that all recycled paper will feed well.
Lexmark consistently tests its printers with recycled paper (20–100% post-consumer waste) and a variety of test paper from around the world, using chamber tests for different temperature and humidity conditions. Lexmark has found no reason to discourage the use of today's recycled office papers, but generally the following property guidelines apply to recycled paper.
Recycled paper, paper of lower weight (
Use these paper storage guidelines to help avoid jams and uneven print quality:
Paper and specialty media guidelines

The following tables provide information on standard and optional paper sources and the types of paper they support.
For information on card stock and labels, see the Card Stock & Label Guide on the Lexmark Web site at www.lexmark.com/publications

Paper size Dimensions 250- or 550-sheet trays (standard or optional)
A4 210 x 297 mm (8.3 x 11.7 in.)
A5 148 x 210 mm (5.8 x 8.3 in.)
A61,2 105 x 148 mm (4.1 x 5.8 in.)
JIS B5 182 x 257 mm (7.2 x 10.1 in.)
Letter 216 x 279 mm (8.5 x 11 in.)
Legal 216 x 356 mm (8.5 x 14 in.)
Executive 184 x 267 mm (7.3 x 10.5 in.)
Oficio1 216 x 340 mm (8.5 x 13.4 in.)
Folio1 216 x 330 mm (8.5 x 13 in.)
Statement1 140 x 216 mm (5.5 x 8.5 in.)
1 This size appears in the Paper Size menu only when the paper source does not support size sensing or when size sensing is turned off.
2 Only the standard exit bin supports this size.
3This size setting formats the page for 216 x 356 mm (8.5 x 14 in.) unless the size is specified by the software application.
4 To support duplexing, the Universal width must be between 148 mm (5.8 in) and 216 mm (8.5 in); Universal length must be between 182 mm (7.2 in) and 356 mm (14 in).
Paper and specialty media guidelines

Paper size Dimensions 250- or 550-sheet trays (standard or optional)
Universal3,4 138 x 210 mm (5.5 x 8.3 in.) up to 216 x 356 mm (8.5 x 14 in.)
70 x 127 mm (2.8 x 5 in.) up to 216 x 356 mm (8.5 x 14 in.)
148 x 182 mm (5.8 x 7.7 in.) up to 216 x 356 mm (8.5 x 14 in.)
7 3/4 Envelope (Monarch)
98 x 191 mm (3.9 x 7.5 in.)
9 Envelope 98 x 225 mm (3.9 x 8.9 in.)
10 Envelope 105 x 241 mm (4.1 x 9.5 in.)
DL Envelope 110 x 220 mm (4.3 x 8.7 in.)
Other Envelope 98 x 162 mm (3.9 x 6.4 in.) to 176 x 250 mm (6.9 x 9.8 in.)
1 This size appears in the Paper Size menu only when the paper source does not support size sensing or when size sensing is turned off.
2 Only the standard exit bin supports this size.
3This size setting formats the page for 216 x 356 mm (8.5 x 14 in.) unless the size is specified by the software application.
4 To support duplexing, the Universal width must be between 148 mm (5.8 in) and 216 mm (8.5 in); Universal length must be between 182 mm (7.2 in) and 356 mm (14 in).
Paper and specialty media guidelines
Optional 2000-sheet tray · Multipurpose feeder · Duplex unit

The printer engine supports 60–176 g/m2 (16–47 lb) paper weights. The duplex unit supports 63–170 g/m2 (17–45 lb) paper weights.
Paper type 250- or 550-sheet trays (standard or optional)
Optional 2000-sheet tray Multipurpose feeder
Envelopes X X X
1 Printing labels requires a special label fuser cleaner which prevents duplexing. The label fuser cleaner is included with the special cartridge required for label applications.
Use this table to determine the possible output destinations of print jobs which use supported paper types and weights. The paper capacity of each output bin is listed in parentheses. Paper capacity estimations are calculated based on 75 g/m2 (20 lb) paper.
Paper and specialty media guidelines

The Finisher supports 60–176 g/m2 (16–47 lb) paper weights.
Paper type Finisher standard bin (250 or 550 sheets)
Output Expander (550 sheets) or High Capacity Output Stacker (1850 sheets)
(500 sheets2)
1 Supports 60-90 g/m2 (16-24 lb) paper weights.
2 Maximum of 50 sheets per stapled packet.
3 Printing labels requires a special label fuser cleaner which prevents duplexing. The label fuser cleaner is included with the special cartridge required for label applications.
Paper and specialty media guidelines


Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the printer control panel, press .
4 If you placed the document on the scanner glass, then touch Finish the Job to return to the home screen.
1 Load an original document faceup, short edge first into the ADF.
2 Adjust the paper guides.
3 On the home screen, touch Copy, or use the keypad to enter the number of copies.
The copy screen appears.
Copying

4 Change the copy settings as needed.
5 Touch Copy It.
1 Place an original document facedown on the scanner glass in the upper left corner.
2 On the home screen, touch Copy, or use the keypad to enter the number of copies.
The copy screen appears.
3 Change the copy settings as needed.
4 Touch Copy It.
5 If you have more pages to scan, then place the next document on the scanner glass, and then touch Scan the Next Page.
6 Touch Finish the Job to return to the home screen.
1 Place a photo facedown on the scanner glass in the upper left corner.
2 On the home screen, touch Copy.
3 Touch Options.
4 Touch Content.
5 Touch Photograph.
6 Touch Done.
7 Touch Copy It.
8 Touch Scan the Next Page or Finish the Job.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Copy from, and then identify the size of the original document.
5 Touch Copy to, and then touch the tray that contains transparencies, or touch Manual Feeder and then place transparencies in the multipurpose feeder.
6 Touch the desired size of the transparencies, and then touch Continue.
Copying

7 Touch the arrows until Transparency appears.
8 Touch Transparency, and then touch Continue.
9 Touch Copy It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Copy from, and then identify the size of the original document.
5 Touch Copy to, and then touch Manual Feeder and place letterhead face up, top edge first in the multipurpose feeder.
6 Touch the desired size of the letterhead, and then touch Continue.
7 Touch the arrows until Letterhead appears.
8 Touch Letterhead, and then touch Continue.
9 Touch Copy It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Copy from, and then identify the size of the original document.
5 Touch Copy to, and then select the size you want the copy to be.
6 Touch Copy It.
Copying

During the copy process, you can select the tray that contains the paper type of choice. For example, if specialty media is located in the multipurpose feeder, and you want to make copies on that media:
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Copy from, and then identify the size of the original document.
5 Touch Copy to, and then touch Manual Feeder or the tray that contains the paper type you want.
6 Touch Copy It.
Use the ADF to copy an original document that contains mixed paper sizes. Depending on the paper sizes loaded and the “Copy to” and “Copy from” settings, each copy is either printed on mixed paper sizes (Example 1) or scaled to fit a single paper size (Example 2).
The printer has two paper trays, one tray loaded with letter-size paper and the other with legal-size paper. A document that contains letter- and legal-size pages needs to be copied.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Copy from, and then touch Auto Size Sense.
5 Touch Copy to, and then touch Auto Size Match.
6 Touch Copy It.
The scanner identifies the mixed paper sizes as they scan. Copies are printed on mixed paper sizes corresponding to the paper sizes of the original document.
Copying

The printer has one paper tray, loaded with letter-size paper. A document that contains letter- and legal-size pages needs to be copied.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Copy from, and then touch Mixed Letter/Legal.
5 Touch Copy to, and then touch Letter.
6 Touch Copy It.
The scanner identifies the mixed paper sizes as they scan and then scales the legal-size pages to print on letter-size paper.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, adjust the paper guides.
3 On the home screen, touch Copy.
4 From the Sides (Duplex) area, touch the button that looks the way you want your copies duplexed.
The first number represents sides of the original documents; the second number represents sides of the copy. For example, select 1-sided to 2-sided if you have 1-sided original documents and you want 2-sided copies.
5 Touch Copy It.
Copies can be reduced to 25% of the original document size or enlarged to 400% of the original document size. The factory default setting for Scale is Auto. If you leave Scale set to Auto, the content of your original document will be scaled to fit the size of the paper onto which you are copying.
To reduce or enlarge a copy:
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
Copying

4 From the Scale area, touch the arrows to enlarge or reduce your copies.
Touching “Copy to” or “Copy from” after setting Scale manually changes the scale value back to Auto.
5 Touch Copy It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Options.
5 Touch Content.
7 Touch Done.
8 Touch Copy It.
If you print multiple copies of a document, then you can choose to print each copy as a set (collated) or to print the copies as groups of pages (not collated).
By default, Collate is set to On. If you do not want to collate your copies, then change the setting to Off.
To turn collation off:
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Use the keypad to enter the number of copies.
Collated Not collated · Copying

5 Touch Off if you do not want your copies collated.
6 Touch Copy It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Options.
5 Touch Separator Sheets.
7 Touch Done.
8 Touch Copy It.
In order to save paper, you can copy either two or four consecutive pages of a multiple-page document onto a single sheet of paper.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Select a duplex setting.
5 Touch Options.
6 Touch Paper Saver.
7 Select the desired output.
8 Touch Print Page Borders if you want a box drawn around each page of the copies.
Copying

9 Touch Done.
10 Touch Copy It.
The custom job or job build is used to combine one or more sets of original documents into a single copy job. Each set may be scanned using different job parameters. When a copy job is submitted and Custom Job is enabled, the scanner scans the first set of original documents using the supplied parameters, and then it scans the next set with the same or different parameters.
The definition of a set depends on the scan source:
For example:
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Options.
5 Touch Custom Job.
6 Touch On.
7 Touch Done.
8 Touch Copy It.
When the end of a set is reached, the scan screen appears.
9 Load the next document faceup, short edge first into the ADF or facedown on the scanner glass, and then touch Scan the Automatic Document Feeder or Scan the flatbed.
10 If you have another document to scan, load the next document faceup, short edge first into the ADF or facedown on the scanner glass, and then touch Scan the Automatic Document Feeder or Scan the flatbed. Otherwise, touch Finish the job.
Copying

Job interrupt pauses the current print job and lets you print copies.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the printer control panel, press .
4 If you placed the document on the scanner glass, then touch Finish the Job to return to the home screen.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Options.
5 Touch Header/Footer.
6 Pick an area of the page to place the date and time.
7 Touch Date/Time, and then touch Continue.
8 Touch Done.
9 Touch Copy It.
An overlay message can be placed on each page. The message choices are Urgent, Confidential, Copy, or Draft. To place a message on the copies:
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Options.
5 Touch Overlay.
Copying

6 Touch the button containing the overlay you want to use.
7 Touch Done.
8 Touch Copy It.
When the ADF begins processing a document, the scanning screen appears. To cancel the copy job, touch Cancel Job on the touch screen.
A “Canceling scan job” screen appears. The ADF clears all pages in the ADF and cancels the job.
Touch Cancel Job on the touch screen.
A “Canceling scan job” screen appears. Once the job is canceled, the copy screen appears.
1 Touch Cancel Job on the touch screen, or press on the keypad.
2 Touch the job you want to cancel.
3 Touch Delete Selected Jobs.
The remaining print job is canceled. The home screen appears.
This option opens a screen where you can enter the size of the documents you are going to copy.
This option opens a screen where you can enter the size and type of paper on which your copies will be printed.
Copying

This option creates an image from your copy that is proportionally scaled anywhere between 25% and 400%. Scale can also be set for you automatically.
This option adjusts how light or dark your copies will turn out in relation to the original document.
This option tells the printer the original document type. Choose from Text, Text/Photo, Photograph, or Printed Image.
Use this option to select duplex settings. You can print copies on one or two sides, make two-sided copies (duplex) of two-sided original documents, make two-sided copies from one-sided original documents, or make one-sided copies (simplex) from two-sided original documents.
This option keeps the pages of a print job stacked in sequence when printing multiple copies of the document. The factory default setting for Collate is on; the output pages of your copies will be ordered (1,2,3) (1,2,3) (1,2,3). If you want all the copies of each page to remain together, turn Collate off, and your copies will be ordered (1,1,1) (2,2,2) (3,3,3).
Touching the Options button opens a screen where you can change Paper Saver, Advanced Imaging, Custom Job, Separator Sheets, Margin Shift, Edge Erase, Header/Footer, Overlay, Content, Advanced Duplex, and Save as Shortcut settings.
Copying

This option lets you print two or more sheets of an original document together on the same page. Paper Saver is also called N-up printing. The N stands for Number. For example, 2-up would print two pages of your document on a single page, and 4-up would print four pages of your document on a single page. Touching Print Page Borders adds or removes the outline border surrounding the original document pages on the output page.
This option lets you adjust Background Removal, Contrast, Shadow Detail, Scan Edge to Edge, Color Balance, and mirror image before you copy the document.
This option combines multiple scanning jobs into a single job.
This option places a blank piece of paper between copies, pages, and print jobs. The separator sheets can be drawn from a tray that contains a type or color of paper that is different from the paper your copies are printed on.
This option increases the size of the margin a specified distance. This can be useful in providing space to bind or hole- punch copies. Use the increase or decrease arrows to set how much of a margin you want. If the additional margin is too large, then the copy will be cropped.
This option eliminates smudges or information around the edges of your document. You can choose to eliminate an equal area around all four sides of the paper, or pick a particular edge. Edge Erase erases whatever is within the selected area, leaving nothing printed on that portion of the paper.
This option turns on the Date/Time, Page number, Bates number, or Custom text and prints them in the specified header or footer location.
This option creates a watermark (or message) that overlays the content of your copy. You can choose between Urgent, Confidential, Copy, and Draft, or you can enter a custom message in the ”Enter custom text” field. The word you pick will appear, faintly, in large print across each page.
This option enhances copy quality. Choose from Text, Text/Photo, Photograph, or Printed Image.
Copying

This option controls whether the documents are one-sided or two-sided, what orientation your original documents have, and how your documents are bound.
This option allows the current settings to be saved as a shortcut.
When should I use Printed Image mode? Use Printed Image mode when copying halftone photographs, graphics
such as documents printed on a laser printer, or pages from a magazine or newspaper
When should I use Photograph mode? Use Photograph mode when the original document is a high-quality photograph or inkjet print.
Question Tip · Copying


Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
You can use the printer to e-mail scanned documents to one or more recipients. There are three ways to send an e-mail from the printer. You can type the e-mail address, use a shortcut number, or use the address book.
For e-mail to operate, it must be turned on in the printer configuration and have a valid IP address or gateway address. To set up the e-mail function:
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Under Default Settings, click E-mail/FTP Settings.
4 Click E-mail Settings.
5 Click Setup E-mail Server.
6 Fill in the fields with the appropriate information.
7 Click Add.
E-mailing

1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Click E-mail/FTP Settings.
4 Click E-mail Settings.
5 Fill in the fields with the appropriate information.
6 Click Submit.
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Under Other Settings, click Manage Shortcuts.
4 Click E-mail Shortcut Setup.
5 Type a unique name for the recipient, and then enter the e-mail address.
6 Select the scan settings (Format, Content, Color, and Resolution).
7 Enter a shortcut number, and then click Add.
If you enter a number that is already in use, then you are prompted to select another number.
1 On the home screen, touch E-mail.
2 Type the recipient's e-mail address.
To create a group of recipients, touch Next address, and then type the next recipient’s e-mail address.
3 Touch Save as Shortcut.
4 Type a unique name for the shortcut, and then touch Enter.
5 Verify that the shortcut name and number are correct, and then touch OK.
If the name or number is incorrect, then touch Cancel, and then reenter the information.
E-mailing

1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch E-mail.
4 Enter the e-mail address or shortcut number.
To enter additional recipients, touch Next Address, and then enter the address or shortcut number you want to add.
5 Touch E-mail It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 Press , and then enter the shortcut number using the keypad.
To enter additional recipients, press Next address, and then enter the address or shortcut number you want to add.
4 Touch E-mail It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, adjust the paper guides.
3 On the home screen, touch E-mail.
4 Touch Search Address Book.
5 Enter the name or part of the name you are searching for, and then touch Search.
6 Touch the name that you want to add to the To: box.
To enter additional recipients, press Next address, and then enter the address or shortcut number you want to add; or search the address book.
7 Touch E-mail It.
E-mailing

1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, adjust the paper guides.
3 On the home screen, touch E-mail.
4 Type an e-mail address.
5 Touch Options.
6 Touch Subject.
7 Type the e-mail subject.
8 Touch Done.
9 Touch Message.
10 Type an e-mail message.
11 Touch Done.
12 Touch E-mail It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch E-mail.
4 Type an e-mail address.
5 Touch Options.
E-mailing

7 Touch E-mail It.
This option opens a screen where you can choose the size of the documents you are going to e-mail.
This option informs the printer if the original document is simplex (printed on one side) or duplex (printed on both sides). This lets the scanner know what needs to be scanned for inclusion in the e-mail.
This option tells the printer whether the original document is in portrait or landscape orientation and then changes the Sides and Binding settings to match the original document orientation.
Tells the printer whether the original document is bound on the long-edge or short-edge side.
This option lets you enter a subject line for your e-mail. You can enter up to 255 characters.
This option lets you customize the attachment file name.
E-mailing

This option lets you enter a message that will be sent with your scanned attachment.
Adjusts the output quality of your e-mail. Increasing the image resolution increases the e-mail file size and the time needed to scan your original document. Image resolution can be decreased to reduce the e-mail file size.
This option sets the output (PDF, TIFF, JPEG or XPS) for the scanned image.
This option tells the printer the original document type. Choose from Text, Text/Photo, or Photo. Color can be turned on or off with any of the Content choices. Content affects the quality and size of your e-mail.
Touching this button opens a screen where you change Advanced Imaging, Custom Job, Transmission Log, Scan Preview, Edge Erase, and Darkness settings.
E-mailing


Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Fax.
4 Enter the fax number or a shortcut using the touch screen or keypad.
To add recipients, touch Next Number, and then enter the recipient's telephone number or shortcut number, or search the address book.
5 Touch Fax It.
Faxing

Faxing from a computer lets you send electronic documents without leaving your desk. This gives you the flexibility of faxing documents directly from software programs.
1 From your software program, click File Print.
2 From the Print window, select your printer, and then click Properties.
3 Choose the Other Options tab, and then click Fax.
4 Click OK, and then click OK again.
5 On the Fax screen, type the name and number of the fax recipient.
6 Click Send.
Instead of entering the entire phone number of a fax recipient on the printer control panel each time you want to send a fax, you can create a permanent fax destination and assign a shortcut number. A shortcut can be created to a single fax number or a group of fax numbers.
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Click Manage Shortcuts.
4 Click Fax Shortcut Setup.
5 Type a unique name for the shortcut, and then enter the fax number.
To create a multiple-number shortcut, enter the fax numbers for the group.
6 Assign a shortcut number.
If you enter a number that is already in use, then you are prompted to select another number.
7 Click Add.
Faxing

1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Fax.
4 Enter the fax number.
To create a group of fax numbers, touch Next number, and then enter the next fax number.
5 Touch Save as Shortcut.
6 Enter a name for the shortcut.
7 Verify that the shortcut name and number are correct, and then touch OK. If the name or number is incorrect, then touch Cancel, and then reenter the information.
If you enter a number that is already in use, then you are prompted to select another number.
8 Touch Fax It to send the fax, or touch
to return to the home screen.
Fax shortcuts are just like the speed dial numbers on a telephone or fax machine. You can assign shortcut numbers when creating permanent fax destinations. Permanent fax destinations or speed dial numbers are created in the Manage Shortcuts link located under Settings on the Embedded Web Server. A shortcut number (1–99999) can contain a single recipient or multiple recipients. By creating a group fax shortcut with a shortcut number, you can quickly and easily fax broadcast information to an entire group.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 Press , and then enter the shortcut number using the keypad.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Fax.
4 Touch Search Address Book.
Faxing

5 Using the virtual keyboard, type the name or part of the name of the person whose fax number you want to find. (Do not attempt to search for multiple names at the same time.)
6 Touch Search.
7 Touch the name to add it to the “Fax to” list.
8 Repeat steps 4 through 7 to enter additional addresses.
9 Touch Fax It.
Adjusting the resolution setting changes the quality of the fax. Settings range from Standard (fastest speed) to Ultra Fine (slowest speed, best quality).
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Fax.
4 Use the keypad to enter the fax number.
5 Touch Options.
6 From the Resolution area, touch the arrows to change to the resolution you want.
7 Touch Fax It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Fax.
4 Use the keypad to enter the fax number.
5 Touch Options.
6 From the Darkness area, touch the arrows to adjust the darkness of the fax.
7 Touch Fax It.
Faxing

1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Fax.
4 Enter the fax number using the numbers on the touch screen or keypad.
5 Touch Options.
6 Touch Advanced Options.
7 Touch Delayed Send.
8 Touch the arrows to adjust the time the fax will be transmitted.
The time is increased or decreased in increments of 30 minutes. If the current time is shown, the left arrow is unavailable.
9 Touch Done.
10 Touch Fax it.
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Click Reports.
4 Click Fax Job Log or Fax Call Log.
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Click Fax Settings.
4 Click Analog Fax Setup.
Faxing

5 Click the Block No Name Fax option.
This option blocks all incoming faxes that have a private caller ID or no fax station name.
6 In the Banned Fax List field, enter the phone numbers or fax station names of specific fax callers you want to block.
1 On the home screen, touch Cancel Jobs.
The Cancel Jobs screen appears.
2 Touch the job or jobs you want to cancel.
Only three jobs appear on the screen; touch the down arrow until the job you want appears, and then touch the job you want to cancel.
3 Touch Delete Selected Jobs.
The Deleting Selected Jobs screen appears, the selected jobs are deleted, and then the home screen appears.
This option opens a screen where you can choose the size of the documents you are going to fax.
This option tells the printer the original document type. Choose from Text, Text/Photo, or Photograph. Color can be turned on or off with any of the Content choices. Content affects the quality and size of your scan.
Faxing

This option informs the printer if the original document is simplex (printed on one side) or duplex (printed on both sides). This lets the scanner know what needs to be scanned for inclusion in the fax.
This options increases how closely the scanner examines the document you want to fax. If you are faxing a photo, a drawing with fine lines, or a document with very small text, increase the Resolution setting. This will increase the amount of time required for the scan and will increase the quality of the fax output.
This option adjusts how light or dark your faxes will turn out in relation to the original document.
Touching this button opens a screen where you can change Delayed Send, Advanced Imaging, Custom Job, Transmission Log, Scan Preview, Edge Erase, and Advanced Duplex settings.
Faxing

When should I use Photo mode? Use Photo mode when faxing photos printed on a laser printer or taken from a magazine or newspaper.
This option lets you hold received faxes from printing until they are released. Held faxes can be released manually or at a scheduled day or time.
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Click Fax Settings.
4 Click Analog Fax Setup.
5 Click Holding Faxes.
6 Enter a password in the Print Faxes Password box.
8 If you selected Scheduled, then continue with the following steps. Otherwise, go to step 9. a Click Fax Holding Schedule. b From the Action menu, select Hold faxes.
c From the Time menu, select the time you want the held faxes released. d From the Day(s) menu, select the day you want the held faxes released.
9 Click Add.
Question Tip · Faxing

This option lets you print and forward received faxes to a fax number, e-mail address, FTP site, or LDSS.
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Click Fax Settings.
4 Click Analog Fax Setup.
7 Click inside the Forward to Shortcut box, and then enter the shortcut number where you want the fax forwarded.
8 Click Submit.
Faxing


Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
The scanner lets you scan documents directly to a File Transfer Protocol (FTP) server. Only one FTP address may be sent to the server at a time.
Once an FTP destination has been configured by your system support person, the name of the destination becomes available as a shortcut number, or it is listed as a profile under the Held Jobs icon. An FTP destination could also be another PostScript printer; for example, a color document can be scanned and then sent to a color printer. Sending a document to an FTP server is similar to sending a fax. The difference is that you are sending the information over your network instead of over the phone line.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, adjust the paper guides.
3 On the home screen, touch FTP.
4 Type the FTP address.
5 Touch Send It.
Scanning to an FTP address

1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 Press #, and then enter the FTP shortcut number.
4 Touch Send It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, adjust the paper guides.
3 On the home screen, touch FTP.
4 Touch Search Address Book.
5 Type the name or part of the name you are searching for, and then touch Search.
6 Touch the name that you want to add to the To: field.
7 Touch Send It.
Instead of entering the entire FTP site address on the control panel each time you want to send a document to an FTP server, you can create a permanent FTP destination and assign a shortcut number. There are two methods for creating shortcut numbers: using a computer or using the printer touch screen.
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Under Other Settings, click Manage Shortcuts.
4 Click FTP Shortcut Setup.
5 Enter the appropriate information into the boxes.
Scanning to an FTP address

6 Enter a shortcut number.
If you enter a number that is already in use, then you are prompted to select another number.
7 Click Add.
1 On the home screen, touch FTP.
2 Type the address of the FTP site.
3 Touch Save as Shortcut.
4 Enter a name for the shortcut.
5 Verify that the shortcut name and number are correct, and then touch OK. If the name or number is incorrect, then touch Cancel, and then reenter the information.
If you enter a number that is already in use, then you are prompted to select another number.
6 Touch Send It to start the scan, or touch
to return to the home screen.
This option opens a screen where you can choose the size of the documents you are going to copy.
This option informs the printer if the original document is simplex (printed on one side) or duplex (printed on both sides). This lets the scanner know what needs to be scanned for inclusion in the document.
This option tells the printer whether the original document is in portrait or landscape orientation and then changes the Sides and Binding settings to match the original document orientation.
Tells the printer whether the original document is bound on the long-edge or short-edge side.
This option adjusts the output quality of your file. Increasing the image resolution increases the file size and the time needed to scan your original document. Image resolution can be decreased to reduce the file size.
Scanning to an FTP address

This option sets the output (PDF, TIFF, JPEG or XPS) for the scanned image.
This option tells the printer the original document type. Choose from Text, Text/Photo, or Photo. Color can be turned on or off with any of the Content choices. Content affects the quality and size of your FTP file.
Touching this button opens a screen where you can change Advanced Imaging, Custom Job, Transmission Log, Scan Preview, Edge Erase, and Darkness settings.
decrease the white portion. – Color Dropout—Color dropout is used for form Optical Character Recognition (OCR) processing. Selecting
Scanning to an FTP address

When should I use Photo mode? Use Photo mode when the original document is composed mostly of photos printed on a laser printer or taken from a magazine or newspaper.
Scanning to an FTP address
Question Tip


Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
The scanner lets you scan documents directly to a computer or a flash drive. The computer does not have to be directly connected to the printer for you to receive Scan to PC images. You can scan the document back to the computer over the network by creating a scan profile on the computer and then downloading the profile to the printer.
1 Type the printer IP address into the address field of your Web browser.
2 Click Scan Profile.
3 Click Create.
4 Select your scan settings, and then click Next.
5 Select a location on your computer where you want to save the scanned output file.
6 Enter a scan name.
The scan name is the name that appears in the Scan Profile list on the display.
7 Click Submit.
8 Review the instructions on the Scan Profile screen.
Scanning to a computer or flash drive

A shortcut number was automatically assigned when you clicked Submit. You can use this shortcut number when you are ready to scan your documents.
a Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
c Press , and then enter the shortcut number using the keypad, or touch Held Jobs on the home screen, and then touch Profiles. d After you enter the shortcut number, the scanner scans and sends the document to the directory or program
you specified. If you touched Profiles on the home screen, then locate your shortcut on the list.
9 Return to the computer to view the file.
The output file is saved in the location you specified or launched in the program you specified.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 Insert the flash drive into the USB port on the front of the printer.
The Held Jobs screen appears.
4 Touch Scan to USB drive.
5 Select the scan settings.
6 Touch Scan It.
This option lets you select preset formats or customize the scan job settings. You can select one of these settings:
Custom Photo - Color JPEG
Text - BW PDF Photo - Color TIFF
Text - BW TIFF Text/Photo - BW PDF Text/Photo - Color PDF
To customize the scan job settings, from the Quick Setup menu, select Custom. Then change the scan settings as needed.
Scanning to a computer or flash drive

This option sets the output (PDF, JPEG, TIFF, SECURE PDF, or XPS) for the scanned image.
This option sets the format used to compress the scanned output file.
This option tells the printer the original document type. Choose from Text, Text/Photo, or Photo. Content affects the quality and size of your scanned file.
Text—Emphasizes sharp, black, high-resolution text against a clean, white background Text/Photo—Used when the original documents are a mixture of text and graphics or pictures Photo—Tells the scanner to pay extra attention to graphics and pictures. This setting increases the time it takes to scan, but emphasizes a reproduction of the full dynamic range of tones in the original document. This increases the amount of information saved.
This option tells the printer the color of the original documents. You can select Gray, BW (Black and White), or Color.
This option sets the size of the documents you are going to scan. When Original Size is set to Mixed Sizes, you can scan an original document that contains mixed paper sizes (letter- and legal-size pages).
This option tells the printer whether the original document is in portrait or landscape orientation and then changes the Sides and Binding settings to match the original document orientation.
This option informs the printer if your original document is simplex (printed on one side) or duplex (printed on both sides). This lets the scanner know what needs to be scanned for inclusion in the document.
This option adjusts how light or dark your scanned documents will turn out in relation to the original document.
Scanning to a computer or flash drive

This option adjusts the output quality of your file. Increasing the image resolution increases the file size and the time needed to scan your original document. Image resolution can be decreased to reduce the file size.
This option lets you adjust Background Removal, Contrast, Shadow Detail, Sharpness, and Color Dropout before you scan the document. It also lets you Scan edge to edge, as a Mirror Image, or as a Negative Image.
When should I use Photo mode? Use Photo mode when scanning photos printed on a laser printer or taken from a magazine or newspaper.
Scanning to a computer or flash drive
Question Tip

This chapter covers printing, printer reports, and job cancelation. Selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 138 and “Storing paper” on page 87.
1 Load paper into a tray or feeder.
2 From the printer control panel Paper menu, set the Paper Type and Paper Size to match the loaded paper.
3 Do one of the following:
a With a document open, click File Print. b Click Properties, Preferences, Options, or Setup, and then adjust the settings as needed.
a Customize the settings as needed in the Page Setup dialog:
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the loaded paper. 3 Click OK. b Customize the settings as needed in the Print dialog:
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the Print dialog and pop-up menus, adjust the settings as needed.
Printing

Print samples on the transparencies being considered for use before buying large quantities.
When printing on transparencies:
Print samples on the envelopes being considered for use before buying large quantities.
When printing on envelopes:
Printing

– Have bent corners – Have rough, cockle, or laid finishes • Adjust the width guide to fit the width of the envelopes.
Print samples on the labels being considered for use before buying large quantities.
For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide available on the Lexmark Web site at www.lexmark.com/publications.
When printing on labels:
releasing hazardous emissions. – Label adhesives, face sheet (printable stock), and topcoats can withstand up to 25 psi (172 kPa) pressure
Card stock is heavy, single-ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly impact print quality. Print samples on the card stock being considered for use before buying large quantities.
When printing on card stock:
Printing

When sending a job to the printer, you can specify that you want the printer to hold the job in memory until you start the job from the printer control panel. All print jobs that can be initiated by the user at the printer are called held jobs.
Confidential When you send a Confidential print job to the printer, you must create a PIN from the computer. The PIN must be four digits using the numbers 0–9. The job is held in printer memory until you enter the PIN from the printer control panel and choose to print or delete the job.
Verify When you send a Verify print job, the printer prints one copy and holds the remaining copies in printer memory. Verify lets you examine the first copy to see if it is satisfactory before printing the remaining copies. Once all copies are printed, the job is automatically deleted from printer memory.
Reserve When you send a Reserve print job, the printer does not print the job immediately. It stores the job in memory so you can print the job later. The job is held in memory until you delete it from the Held Jobs menu.
Repeat When you send a Repeat print job, the printer prints all requested copies of the job and stores the job in memory so you can print additional copies later. You can print additional copies as long as the job remains stored in memory.
Other types of held jobs include:
Job type Description · Printing

1 With a document open, click File Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Other Options, and then click Print and Hold.
4 Select your job type (Confidential, Reserve, Repeat, or Verify), and then assign a user name. For a confidential job, also enter a four-digit PIN.
5 Click OK or Print, and then go to the printer to release the job.
6 On the home screen, touch Held jobs.
7 Touch your user name.
8 Touch Confidential Jobs.
9 Enter your PIN.
10 Touch the job you want to print.
11 Touch Print, or touch the arrows to increase or decrease the number of copies, and then touch Print.
1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages pop-up menu, choose Job Routing.
3 Select your job type (Confidential, Reserve, Repeat, or Verify), and then assign a user name. For a confidential job, also enter a four-digit PIN.
4 Click OK or Print, and then go to the printer to release the job.
5 On the home screen, touch Held jobs.
6 Touch your user name.
7 Touch Confidential Jobs.
8 Enter your PIN.
9 Touch the job you want to print.
10 Touch Print, or touch the arrows to increase or decrease the number of copies, and then touch Print.
Printing

A USB port is located on the printer control panel. Insert a flash drive to print supported file types. Supported file types include: .pdf, .gif, .jpeg, .jpg, .bmp, .png, .tiff, .tif, .pcx, and .dcx.
Many flash drives are tested and approved for use with the printer. For more information, visit the Lexmark Web site at www.lexmark.com.
To print from a flash drive:
1 Make sure the printer is on and Ready appears.
2 Insert a flash drive into the USB port.

3 Touch the document you want to print.
Printing

4 Touch the arrows if you want to increase the number of printed copies.
5 Touch Print.
If you leave the flash drive in the printer after leaving the initial USB menu screen, then you can still print .pdf files from the flash drive as held jobs.
A directory list shows the resources stored in flash memory or on the printer hard disk.
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch
3 Touch Reports.
4 Touch the down arrow until Print Directory appears.
5 Touch Print Directory.
Print the print quality test pages to isolate print quality problems.
1 Turn the printer off.
2 Hold down 2 ABC and
6 MNO while turning the printer on.
3 Release the buttons when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears.
4 Touch the down arrow until Print Quality Pages appears.
5 Touch Print Quality Pages.
The print quality test pages print.
6 Touch Back.
7 Touch Exit Configuration.
1 Touch Cancel Jobs on the touch screen, or press on the keypad.
2 Touch the job you want to cancel.
3 Touch Delete Selected Jobs.
Printing

To cancel a print job, do one of the following:
In Windows Vista:
2 Click Control Panel.
3 Click Hardware and Sound.
4 Click Printers.
5 Double-click the printer icon.
6 Select the job to cancel.
7 From the keyboard, press Delete.
In Windows XP:
1 Click Start.
2 From Printers and Faxes, double-click the printer icon.
3 Select the job to cancel.
4 From the keyboard, press Delete.
From the Windows taskbar:
When you send a job to print, a small printer icon appears in the right corner of the taskbar.
1 Double-click the printer icon.
A list of print jobs appears in the printer window.
2 Select a job to cancel.
3 From the keyboard, press Delete.
In Mac OS X version 10.5:
1 From the Apple menu, choose System Preferences.
2 Click Print & Fax, and then double-click the printer icon.
3 From the printer window, select the job to cancel.
4 From the icon bar at the top of the window, click the Delete icon.
In Mac OS X version 10.4 and earlier:
1 From the Go menu, choose Applications.
2 Double-click Utilities, and then double-click Print Center or Printer Setup Utility.
3 Double-click the printer icon.
1 Click · Printing

4 From the printer window, select the job to cancel.
5 From the icon bar at the top of the window, click the Delete icon.
Printing

Jam error messages appear on the control panel display and include the area of the printer where the jam occurred. When there is more than one jam, the number of jammed pages is displayed.
The following hints can help you avoid jams.
Clearing jams

When a jam occurs, a message indicating the jam location appears. Open doors and covers and remove trays to access jam locations. To resolve any paper jam message, you must clear all jammed paper from the paper path.
The following table lists the jams that can occur and the location of each jam:


1 Touch Status/Supplies to identify the location of the jam.
2 Lower the multipurpose feeder door.
Clearing jams

3 Push the release latch, and then open the front cover.

4 Lift and pull the print cartridge out of the printer.

Clearing jams

5 Place the print cartridge aside.
6 Remove the jammed paper.
7 Align and reinstall the print cartridge.
8 Close the front cover.
9 Close the multipurpose feeder door.
10 Touch Continue.
Touch Status/Supplies to identify the location of the jam. If the paper is exiting the printer, then pull the paper out, and then touch Continue.
If the paper is not exiting the printer:
1 Pull down the top rear door.

2 Remove the jammed paper.
3 Close the top rear door.
4 Touch Continue.
Clearing jams

1 Touch Status/Supplies to identify the location of the jam.
2 Pull the standard tray out.
3 Pull down the bottom rear door.

4 Push the tab down.

5 Remove the jammed paper.
6 Close the bottom rear door.
7 Insert the standard tray.
8 Touch Continue.
Clearing jams

1 Touch Status/Supplies to identify the location of the jam.
2 Pull the standard tray out.

3 Remove any jammed paper, and then close the tray.
4 Touch Continue.
5 If the jam message persists, then pull out any optional trays.
6 Remove the jammed paper, and then insert the trays.
7 Touch Continue.
Clearing jams

1 Touch Status/Supplies to identify the location of the jam.
2 Remove the paper from the multipurpose feeder.

3 Flex the sheets of paper back and forth to loosen them, and then fan them. Do not fold or crease the paper. Straighten the edges on a level surface.
4 Load the paper into the multipurpose feeder.
5 Slide the paper guide toward the inside of the tray until it lightly rests against the edge of the paper.

6 Touch Continue.
Clearing jams

Touch Status/Supplies to identify the location of the jam. The envelope feeder feeds envelopes from the bottom of the stack; the bottom envelope will be the one that is jammed.
1 Lift the envelope weight.
2 Remove all envelopes.
3 If the jammed envelope has entered the printer and cannot be pulled out, then lift the envelope feeder up and then out of the printer, and then set it aside.
4 Remove the envelope from the printer.
5 Reinstall the envelope feeder. Make sure it snaps into place.
6 Flex and stack the envelopes.
7 Load the envelopes in the envelope feeder.
8 Adjust the paper guide.
9 Lower the envelope weight.
10 Touch Continue.
To clear a jam in the high-capacity output stacker or the 4-bin mailbox:
1 Touch Status/Supplies to identify the location of the jam.
2 If the paper is exiting into a bin, then pull the paper straight out, and then touch Continue.
If not, then continue with step 3.
3 Pull down the output bin door or doors.
4 Remove the jammed paper.
5 Close the output bin door or doors.
6 Touch Continue.
1 Touch Status/Supplies to identify the location of the jam.
2 Pull down the StapleSmart finisher door.
3 Remove the jammed paper.
4 Close the StapleSmart finisher door.
5 Touch Continue.
Clearing jams

1 Touch Status/Supplies to identify the location of the jam.
2 Press the latch to open the stapler door.

3 Pull the latch of the staple cartridge holder down, and then pull the holder out of the printer.

Clearing jams

4 Use the metal tab to lift the staple guard, and then remove any loose staples.

5 Close the staple guard.

6 Press down on the staple guard until it snaps into place.

Clearing jams

7 Push the cartridge holder firmly back into the stapler unit until the cartridge holder clicks into place.
8 Close the stapler door.
1 Remove all original documents from the ADF.
2 Open the ADF cover, and then remove any jammed paper.

3 Close the ADF cover.
4 Open the scanner cover, and then remove any jammed pages.

Clearing jams

5 Open the bottom ADF door, and then remove any jammed pages.

6 Close the bottom ADF door and scanner cover.
7 Touch Restart Job.
Clearing jams

Menus list
A number of menus are available to make it easy for you to change printer settings. To access the menus, touch
on the home screen.
Paper Menu Reports Network/Ports
Default Source Paper Size/Type Configure MP Envelope Enhance Substitute Size Paper Texture Paper Weight Paper Loading Custom Types Custom Names Custom Scan Sizes Custom Bin Names Universal Setup Bin Setup
Menu Settings Page Device Statistics Network Setup Page Network Setup Page
SMTP Setup Standard USB Parallel Serial
Wireless Setup Page1
Shortcut List Fax Job Log Fax Call Log Copy Shortcuts E-mail Shortcuts Fax Shortcuts FTP Shortcuts Profiles List NetWare Setup Page Print Fonts Print Directory Asset Report
1 Only appears if a wireless card is installed.
2 Depending on the printer setup, this menu item appears as Standard Network or Network .
Edit Security Setups Miscellaneous Security Settings Confidential Print Disc Wiping Security Audit Log Set Date and Time
General Settings Copy Settings Fax Settings E-mail Settings FTP Settings Flash Drive Menu Print Settings
Print all guides Copy guide E-mail guide Fax guide FTP guide Information guide Print Defects guide Supplies Guide

Sets a default paper source for all print jobs
Tray MP Feeder Envelope Feeder Manual Paper Manual Env
Specifies the paper size loaded in each tray
A4 A5 A6 JIS B5 Letter Legal Executive1
1 Appears only if Tray Size Sensing is turned off.

Specifies the type of paper loaded in each tray
Plain Paper Card Stock Transparency Recycled Labels Vinyl Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Paper Custom Type
Specifies the paper size loaded in the multipurpose feeder
A4 A5 A6 JIS B5 Letter Legal Executive Oficio Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope Other Envelope
1 Appears only if Tray Size Sensing is turned off.

Specifies the type of paper loaded in the multipurpose feeder
Plain Paper Card Stock Transparency Recycled Labels Vinyl Labels Bond Envelope Rough Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Paper Custom Type
Specifies the envelope size loaded in the envelope feeder
7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope Other Envelope
Specifies the type of envelope loaded in the envelope feeder
Envelope Rough Envelope Custom Type
1 Appears only if Tray Size Sensing is turned off.

Specifies the size of the paper being manually loaded
A4 A5 A6 JIS B5 Letter Legal Executive Oficio Folio Statement Universal
Specifies the type of paper being manually loaded
Plain Paper Card Stock Transparency Recycled Labels Vinyl Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Rough/Cotton Paper Custom Type
Specifies the size of the envelope being manually loaded
7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope Other Envelope
Specifies the type of envelope being manually loaded
Envelope Rough Envelope Custom Type
1 Appears only if Tray Size Sensing is turned off.

Determines when the printer selects paper from the multipurpose feeder
The envelope conditioner significantly reduces the wrinkling of some envelopes.
Enables or disables the envelope conditioner
Off 1 (Least) 2 3 4 5 6 (Most)
Substitutes a specified paper size if the requested paper size is not available
Off Statement/A5 Letter/A4 All Listed

Specifies the relative texture of the paper loaded in a specific tray
Specifies the relative texture of the card stock loaded in a specific tray
Specifies the relative texture of the transparencies loaded in a specific tray
Specifies the relative texture of the recycled paper loaded in a specific tray
Specifies the relative texture of the labels loaded in a specific tray
Specifies the relative texture of the vinyl labels loaded in a specific tray
Specifies the relative texture of the paper loaded in a specific tray
Specifies the relative texture of the envelopes loaded in a specific tray
Specifies the relative texture of the rough envelopes loaded in a specific tray

Specifies the relative texture of the paper loaded in a specific tray
Specifies the relative texture of the paper loaded in a specific tray
Specifies the relative texture of the paper loaded in a specific tray
Specifies the relative texture of the paper loaded in a specific tray
Specifies the relative texture of the paper loaded in a specific tray
Specifies the relative texture of the paper loaded in a specific tray
Specifies the relative texture of the custom paper loaded in a specific tray
Specifies the relative weight of the paper loaded in a specific tray
Specifies the relative weight of the card stock loaded in a specific tray

Specifies the relative weight of the paper loaded in a specific tray
Specifies the relative weight of the recycled paper loaded in a specific tray
Specifies the relative weight of the labels loaded in a specific tray
Specifies the relative weight of the vinyl labels loaded in a specific tray
Specifies the relative weight of the paper loaded in a specific tray
Specifies the relative weight of the envelopes loaded in a specific tray
Specifies the relative weight of the rough envelopes loaded in a specific tray
Specifies the relative weight of the paper loaded in a specific tray
Specifies the relative weight of the paper loaded in a specific tray
Specifies the relative weight of the paper loaded in a specific tray

Specifies the relative weight of the paper loaded in a specific tray
Specifies the relative weight of the paper loaded in a specific tray
Specifies the relative weight of the paper loaded in a specific tray
Specifies the relative weight of the custom paper type loaded in a specific tray
Determines whether 2-sided printing occurs for all jobs that specify Card Stock as the paper type
Determines whether 2-sided printing occurs for all jobs that specify Recycled as the paper type
Determines whether 2-sided printing occurs for all jobs that specify Labels as the paper type
Determines whether 2-sided printing occurs for all jobs that specify Vinyl Labels as the paper type
Determines whether 2-sided printing occurs for all jobs that specify Bond as the paper type
Determines whether 2-sided printing occurs for all jobs that specify Letterhead as the paper type

Determines whether 2-sided printing occurs for all jobs that specify Preprinted as the paper type
Determines whether 2-sided printing occurs for all jobs that specify Colored as the paper type
Determines whether 2-sided printing occurs for all jobs that specify Light as the paper type
Determines whether 2-sided printing occurs for all jobs that specify Heavy as the paper type
Determines whether 2-sided printing occurs for all jobs that specify Rough as the paper type
Determines whether 2-sided printing occurs for all jobs that specify Custom as the paper type
Associates a paper or specialty media type with a factory default Custom Type <x> name or a user-defined Custom Name created from the Embedded Web Server or MarkVision Professional
Paper Card Stock Transparency Labels Vinyl Labels Envelope

Specifies a paper type when the Recycled setting is selected in other menus
Paper Card Stock Transparency Labels Vinyl Labels Envelope
Specify a custom name for a paper type. This name replaces a Custom Type <x> name in the printer menus.
Custom Scan Size <x>
Specifies a custom scan size name and options. This name replaces a Custom Scan Size <x> name in the printer menus.
Scan Size Name Width
3–14.17 inches (76–360 mm) Height
3–14.17 inches (76–360 mm) Orientation
Landscape Portrait 2 scans per side Off On ADF Pick Roller Force
User Default 30% 40% 50% 60% 70% 80%

Standard Bin Specifies a custom name for the Standard Bin
Bin 1 Specifies a custom name for Bin 1
These menu items are used to specify the height, width, and feed direction of the Universal Paper Size. The Universal Paper Size is a user-defined paper size setting. It is listed with the other paper size settings and includes similar options, such as support for duplex printing and printing multiple pages on one sheet.
Identifies the units of measure
Sets the portrait width
3–14 inches 76–360 mm
Sets the portrait height
3–14 inches 76–360 mm
Specifies the feed direction if the paper can be loaded in either direction
Short Edge Long Edge

Identifies installed output bins
Standard Bin Bin
Specifies configuration options for output bins
Mailbox Link Mail Overflow Link Optional Type Assignment
Selects an output bin for each supported paper type Available selections for each type are:
Plain Paper Bin Card Stock Bin Transparency Bin Recycled Bin Labels Bin Vinyl Labels Bin Bond Bin Envelope Bin Rough Envelope Bin Letterhead Bin Preprinted Bin Colored Bin Light Bin Heavy Bin Rough Bin Custom Bin
Disabled Standard Bin Bin

Menu Settings Page Prints a report containing information about paper loaded into trays, installed memory, the total page count, alarms, timeouts, the control panel language, the TCP/IP address, the status of supplies, the status of the network connection, and other information
Device Statistics Prints a report containing printer statistics such as supply information and details about printed pages
Network Setup Page Prints a report containing information about the network printer settings, such as the TCP/IP address information
Network <x> Setup Page Prints a report containing information about the network printer settings, such as the TCP/IP address information
Wireless Setup Page Prints a report containing information about the wireless network printer settings, such as the TCP/IP address information
Shortcut List Prints a report containing information about configured shortcuts
Fax Job Log Prints a report containing information about the last 200 completed faxes
Fax Call Log Prints a report containing information about the last 100 attempted, received, and blocked calls
Copy Shortcuts Prints a report containing information about copy shortcuts
E-mail Shortcuts Prints a report containing information about e-mail shortcuts
Fax Shortcuts Prints a report containing information about fax shortcuts
FTP Shortcuts Prints a report containing information about FTP shortcuts
Profiles List Prints a list of profiles stored in the printer
Menu item Description · Understanding printer menus

NetWare Setup Page Prints a report containing NetWare-specific information about the network settings
Print Fonts Prints a report of all the fonts available for the printer language currently set in the printer
Print Directory Prints a list of all the resources stored on an optional flash memory card or printer hard disk
Asset Report Prints a report containing asset information including the printer serial number and model name. The report contains text and UPC barcodes that can be scanned into an asset database.
Auto
Sets the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language

Sets the printer to automatically switch to PS emulation when a print job requires it, regardless of the default printer language
Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol
Sets the size of the network input buffer
Auto 3K to
Temporarily stores jobs on the printer hard disk before printing. This menu only appears if a formatted disk is installed.

Sets the printer to process Macintosh binary PostScript print jobs
For descriptions and settings of the network setup menus, see the following:
Reports or Network Reports Network Card TCP/IP IPv6 AppleTalk NetWare LexLink
Reports or Network Reports Network Card TCP/IP IPv6 Wireless AppleTalk NetWare LexLink
Use the following menu to configure the SMTP server.
Primary SMTP Gateway Primary SMTP Gateway Port Secondary SMTP Gateway Secondary SMTP Gateway Port
Specifies SMTP server port information
5–30 Specifies the amount of time in seconds before the server stops trying to send the e-mail
Reply Address Use SSL
Specifies server information. This is a required item.

Specifies the type of user authentication required for scan to e-mail privileges
No authentication required Login / Plain CRAM-MD5 Digest-MD5 NTLM Kerberos 5
None Use Device SMTP Credentials
None Use Device SMTP Credentials Use Session User ID and Password Use Session E-mail address and Password Prompt User
Device Userid Device password Kerberos 5 Realm NTLM Domain
This menu is available from the Network/Ports menu:
Network/Ports Standard Network or Network <x> Std Network Setup or Net <x> Setup Reports or Network Reports
Print Setup Page Print NetWare Setup Page
Prints a report containing information about the current network setup
This menu is available from the Network/Ports menu:

Network/Ports Standard Network or Network <x> Std Network Setup or Net <x> Setup Network Card
Lets you view the connection status of the Network Card
View Card Speed Lets you view the speed of a currently active network card
Lets you view the network addresses
Job Timeout 0-225 seconds Sets the amount of time in seconds that a network print job can take before it is canceled
Allows the printer to print a banner page
Use the following menu items to view or set the TCP/IP information.
This menu is available from the Network/Ports menu:
Network/Ports Standard Network or Network <x> Std Network Setup or Net <x> Setup TCP/IP
View Hostname Lets you view the current TCP/IP hostname
IP Address Lets you view or change the current TCP/IP Address
Netmask Lets you view or change the current TCP/IP Netmask
Gateway Lets you view or change the current TCP/IP Gateway

Specifies the DHCP address and parameter assignment setting
Specifies the RARP address assignment setting
Specifies the BOOTP address assignment setting
Specifies the Zero Configuration Networking setting
Enables the built-in FTP server, which allows you to send files to the printer using the File Transfer Protocol.
Enables the built-in web server (Embedded Web Server). When enabled, the printer can be monitored and managed remotely using a web browser.
WINS Server Address Lets you view or change the current WINS Server Address
DNS Server Address Lets you view or change the current DNS Server Address
Use the following menu items to view or set the Internet Protocol version 6 (IPv6) information.
This menu is available from the Network/Ports menu:
Network/Ports Standard Network or Network <x> Std Network Setup or Net <x> Setup IPv6
Enables IPv6 in the printer
Specifies whether the network adapter accepts the automatic IPv6 address configuration entries provided by a router
View Hostname View Address View Router Address
Lets you view the current setting

Enables DHCPv6 in the printer
Use the following menu items to view or configure the wireless internal print server settings.
This menu is available from the Network/Ports menu:
Network/Ports Network <x> Net <x> Setup Wireless
Specifies the network mode
Specifies the wireless standard for the wireless network
802.11n 802.11b/g 802.11b/g/n
Lets you select an available network for the printer to use
View Signal Quality Lets you view the quality of the wireless connection
View Security Mode Lets you view the encryption method for the wireless connection. “Disabled” indicates that the wireless network is not encrypted.
This menu is available from the Network/Ports menu:
Network/Ports Standard Network or Network <x> Std Network Setup or Net <x> Setup AppleTalk
View Name Shows the assigned AppleTalk name

View Address Shows the assigned AppleTalk address
Provides a list of AppleTalk zones available on the network
This menu is available from the Network/Ports menu:
Network/Ports Standard Network or Network <x> Std Network Setup or Net <x> Setup NetWare
View Login Name Lets you view the assigned NetWare login name
Print Mode Lets you view the assigned NetWare print mode
Network Number Lets you view the assigned NetWare network number
Enables the Ethernet frame type setting
Ethernet 802.2 Ethernet 802.3 Ethernet Type II Ethernet SNAP
Reduces network traffic by allowing the transfer and acknowledgement of multiple data packets to and from the NetWare server
Specifies the NSQ/GSQ Mode setting
This menu is available from the Network/Ports menu:

Network/Ports Standard Network or Network <x> Std Network Setup or Net <x> Setup LexLink menu
View Nickname Lets you view the assigned LexLink nickname
Sets the printer to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language
Sets the printer to automatically switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language
Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol

Sets the size of the USB input buffer
Disabled Auto 3K to
Temporarily stores jobs on the printer hard disk before printing
Sets the printer to process Macintosh binary PostScript print jobs
Sets the network address, netmask, or gateway information for an external print server that is attached to the printer using a USB cable.
ENA Address ENA Netmask ENA Gateway

This menu appears only if an optional parallel card is installed.
Sets the printer to automatically switch to PCL emulation when a print job received through a parallel port requires it, regardless of the default printer language
Sets the printer to automatically switch to PS emulation when a print job received through a parallel port requires it, regardless of the default printer language
Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol
Sets the size of the parallel input buffer
Disabled Auto 3K to

Temporarily stores jobs on the printer hard disk before printing
Enables bidirectional communication through the parallel port
Specifies the parallel port protocol
Determines whether or not the printer honors printer hardware initialization requests from the computer
Determines whether the parallel port data is sampled on the leading or trailing edge of strobe
Sets the printer to process Macintosh binary PostScript print jobs

Sets the network address, netmask, or gateway information for an external print server that is attached to the printer using a parallel cable.
ENA Address ENA Netmask ENA Gateway
This menu appears only if an optional serial card is installed.
Sets the printer to automatically switch to PCL emulation when a print job received through a serial port requires it, regardless of the default printer language
Sets the printer to automatically switch to PS emulation when a print job received through a serial port requires it, regardless of the default printer language
Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol

Sets the size of the serial input buffer
Disabled Auto 3K to
Temporarily stores jobs on the printer hard disk before printing
Selects the hardware and software handshaking settings for the serial port
Determines whether or not the printer communicates availability to the computer

Specifies the rate at which data can be received through the serial port
1200 2400 4800 9600 19200 38400 57600 115200 138200 172800 230400 345600
Specifies the number of data bits that are sent in each transmission frame
Sets the parity for serial input and output data frames
Even Odd None Ignore
Determines whether the printer uses the DSR Signal. DSR is a handshaking signal used by most serial cables.

Limits the number and time frames of failed login attempts from the printer control panel before all users are locked out
Login failures Failure time frame Lockout time Login timeout
Limits the number and time frames of failed login attempts from a computer before all remote users are locked out
Login failures Failure time frame Lockout time Login timeout

Limits the number of times an invalid PIN can be entered
Limits the amount of time a confidential job stays in the printer before it is deleted
Off 1 hour 4 hours 24 hours 1 week
Disk Wiping erases only print job data that is not currently in use by the file system from the printer hard disk. All permanent data on the printer hard disk is preserved, such as downloaded fonts, macros, and held jobs.
Automatic Wiping marks all disk space used by a previous job and does not permit the file system to reuse this space until it has been sanitized. Only Automatic Wiping enables users to activate disk wiping without having to take the printer offline for an extended amount of time.

Disk Wiping erases only print job data that is not currently in use by the file system from the printer hard disk. All permanent data on the printer hard disk is preserved, such as downloaded fonts, macros, and held jobs. Manual Wiping overwrites all disk space that has been used to hold data from a print job that has been processed (i.e. printed). This type of wipe does not erase any information related to an unprocessed print job.
Start now Do not start now
Disk Wiping erases only print job data that is not currently in use by the file system from the printer hard disk. All permanent data on the printer hard disk is preserved, such as downloaded fonts, macros, and held jobs.
Single pass Multiple pass
Disk Wiping erases only print job data that is not currently in use by the file system from the printer hard disk. All permanent data on the printer hard disk is preserved, such as downloaded fonts, macros, and held jobs. Both manual and scheduled wiping allow the file system to reuse marked disk space without first having to wipe it.
Single pass Multiple pass

Disk Wiping erases only print job data that is not currently in use by the file system from the printer hard disk. All permanent data on the printer hard disk is preserved, such as downloaded fonts, macros, and held jobs. Both manual and scheduled wiping allow the file system to reuse marked disk space without first having to wipe it.
Single pass Multiple pass
Export Log Enables an authorized user to export the security log
Specifies whether audit logs are deleted
Delete now Do not delete
Specifies whether and how the audit logs are created
Enable Audit Enable Remote Syslog Remote Syslog Facility Severity of events to log
View Date/Time Lets you view the current date and time settings for the printer

Enables Network Time Protocol, which synchronizes the clocks of devices on a network
Sets the language of the text appearing on the display
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portuguese Suomi Russian Polski Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese

Minimizes the use of energy, paper, or specialty media
Off Energy Energy/Paper Paper
Specifies whether the ADF emits a beep when paper is loaded
Reduces the amount of noise produced by the printer
Instructs the printer to run the setup wizard

Specifies a language and custom key information for the printer control panel keyboard. The additional tabs enable access to accent marks and symbols from the printer control panel keyboard.
English Francais Francais Canadien Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Suomi Portuguese Russian Polski Swiss German Swiss French Turkce Korean Custom Key Accents/Symbols Tab
On Off Russian/Polish Tab
On Off Korean Tab
Specifies the printer factory default measurements. The default is determined by the country/region selection in the initial setup wizard.
U.S. Metric
Scan to PC Port Range
Specifies a valid port range for printers behind a port blocking firewall. The valid ports are specified by two sets of numbers separated by a semicolon.

Specifies what is displayed on the upper left and right corners of the home screen For the Left side and Right side options, choose from the following options:
Left side Right side Custom Text
Black Toner
None IP Address Hostname Contact Name Location Date/Time mDNS/DDNS Service Name Zero Configuration Name Cartridge Level Custom Text
Display When Supply Registers
Off Early Warning Low Near End of Life End of Life Type of Message to Display
Default Alternate Default Message
Alternate Message
The displayed information for Paper Jam, Load Paper, and Service Errors can be customized with the following options:
Paper Jam Load Paper Service Errors
Yes No Type of Message to Display
Default Alternate Default Message
Alternate Message

Additional buttons can be added to the Home screen, and default buttons can be removed. Available selections for each button are:
Change Language Copy Copy Shortcuts Fax Fax Shortcuts E-mail E-mail Shortcuts FTP FTP Shortcuts Search Held Jobs Held Jobs USB Drive Profiles Bookmarks Jobs by user
Display Do Not Display
Formats the printer date
Formats the printer time
12 hour A.M./P.M. 24 hour clock
20–100 Specifies the brightness of the printer control panel screen
Sets the copies from the scanner glass to only one page at a time

Sets the amount of light from the standard bin or an optional output bin
Bright Dim Off Power Saver
Bright Dim Off Output Option Bin LEDs
Bright Dim Off Power Saver
Specifies whether bookmarks are displayed from the Held Jobs area
Specifies whether image background removal is allowed during copy, fax, e-mail, FTP, or scan to USB
Allow Custom Job Scans
Lets you scan multiple jobs to one file
Specifies how a scanned job should be reloaded if a paper jam occurs in the ADF
Job level Page level
Web Page Refresh Rate
30–300 Specifies the number of seconds between Embedded Web Server refreshes

Contact Name Specifies a contact name for the printer
Location Specifies the location of the printer
Sets an alarm to sound when the printer requires operator intervention Available selections for each alarm type are:
Alarm Control Cartridge Alarm Staple Alarm
Sets the amount of time the printer waits for user intervention before it holds jobs that require unavailable resources and continues to print other jobs in the print queue
Specifies the number of minutes of inactivity before the system enters a lower power state
Specifies the number of minutes of inactivity before some systems begin entering a minimum power state.
Sets the amount of time in seconds the printer waits before returning the printer display to a Ready state

Sets the amount of time in seconds the printer waits to receive an end-of-job message before canceling the remainder of the print job
Sets the amount of time in seconds the printer waits for additional data before canceling a print job
Lets the printer automatically continue printing from certain offline situations when not resolved within the specified time period
Specifies whether the printer reprints jammed pages
Lets the printer successfully print a page that may not have printed otherwise

Returns the printer settings to the factory default settings
Do Not Restore Restore Now
Specifies the type of content contained in the copy job
Text/Photo Photograph Printed Image Text
Specifies whether an original document is duplex (two-sided) or simplex (one- sided), and then specifies whether the copy should be duplex or simplex
1 sided to 1 sided 1 sided to 2 sided 2 sided to 1 sided 2 sided to 2 sided

Sets two or four sheets of an original document together on the same page
Off 2 on 1 Portrait 2 on 1 Landscape 4 on 1 Portrait 4 on 1 Landscape
Specifies whether a border is printed around the edge of the page at the margins
Keeps the pages of a print job stacked in sequence when making multiple copies of the job
Specifies the paper size of the original document
Letter Legal Executive Folio Statement Universal 4 x 6 in. 3 x 5 in. Business Card Custom Scan Size A4 A5 Oficio (Mexico) A6 JIS B5 Book Original Auto Size Sense Mixed Letter/Legal
Specifies the paper source for copy jobs
Tray Single Sheet Feeder Multi Sheet Feeder Auto Size Match

Places a sheet of paper between transparencies
Places a sheet of paper between pages, copies, or jobs based on the value selected
None Between Copies Between Jobs Between Pages
Specifies a paper source
Tray Manual Feeder Envelope Feeder
1–9 Specifies the level of darkness for the copy job
Specifies which output bin receives the copy after it is printed
Standard Bin Bin
Number of Copies Specifies the number of copies for the copy job
Specifies header/footer information for the top left of the page
Off Date/Time Page number Bates number Custom text Print on
All pages First page only All but first page Enter custom text

Specifies header/footer information for the middle of the page
Off Date/Time Page number Bates number Custom text Print on
All pages First page only All but first page Enter custom text
Specifies header/footer information for the top right of the page
Off Date/Time Page number Bates number Custom text Print on
All pages First page only All but first page Enter custom text
Specifies header/footer information for the bottom left of the page
Off Date/Time Page number Bates number Custom text Print on
All pages First page only All but first page Enter custom text

Specifies header/footer information for the bottom middle of the page
Off Date/Time Page number Bates number Custom text Print on
All pages First page only All but first page Enter custom text
Specifies header/footer information for the bottom right of the page
Off Date/Time Page number Bates number Custom text Print on
All pages First page only All but first page Enter custom text
Specifies overlay text that is printed on each page of the copy job
Off Confidential Copy Draft Urgent Custom
Custom Overlay Specifies custom overlay text
Allows interruption of a print job to copy a page or document
Lets you copy in a single copy job a document that contains mixed paper sizes

Allow Save as Shortcut
Lets you save custom copy settings as shortcuts
Adjusts the amount of background visible on a copy
Lets you automatically center the copy on the page
Specifies which color to drop during copies, and how much to increase or decrease the dropout
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specifies the contrast used for the copy job
0–5 Best for content
Creates a mirror image of the original document
Creates a negative image of the original document
0–4 Adjusts the amount of shadow detail visible on a copy
Scan edge to edge
Specifies if the original document is scanned edge-to-edge prior to copying
0–5 Adjusts the amount of sharpness on a copy
Creates a sample copy of the original document

Analog Fax Setup mode sends the fax job by way of a telephone line.
Configures the fax cover page
Off by default On by default Never Use Always Use Include To field
On Off Include From field
On Off From Include Message field
On Off Message Include Logo
On Off Include Footer
Station Name Specifies the name of the fax within the printer
Station Number Specifies a number associated with the fax
Specifies how the fax is identified
Station Name Station Number
Sets the printer to fax manually only, which requires a line splitter and a telephone hand set

Defines the allocation of non-volatile memory between sending and receiving fax jobs
All receive Mostly receive Equal Mostly sent All send
Specifies whether the printer may cancel fax jobs
Specifies type of caller ID being used
Specifies the direction from which digits are masked in an outgoing fax number
Off From left From right
0–58 Specifies the number of digits to mask in an outgoing fax number
Specifies quality in dots per inch (dpi). A higher resolution gives greater print quality, but it increases the fax transmission time for outgoing faxes.
Standard Fine Super Fine Ultra Fine

Specifies the paper size of the document that is being scanned
Letter Legal Executive Folio Statement Universal 4 x 6 in. 3 x 5 in. Business Card Custom Scan Size A4 A5 Oficio (Mexico) A6 JIS B5 Book Original Auto Size Sense Mixed Letter/Legal
Specifies how the text and graphics are oriented on the page
Off Long edge Short edge
Specifies the type of content that will be scanned to fax
1–9 Lightens or darkens the output
Dial Prefix A numeric entry field is provided to enter numbers
Establishes a dialing prefix rule

0–9 Specifies the number of times the printer tries to send the fax to a specified number
1–200 Specifies the number of minutes between redials
Enables switchboard blind dialing without a dial tone
Enables Error Correction Mode for fax jobs
Lets you send faxes by scanning at the printer
Allows driver to fax jobs to be sent by the printer
Allow Save as Shortcut
Lets you save fax numbers as shortcuts in the printer
Specifies the dialing sound, either as a tone or a pulse.
Specifies the maximum speed in baud at which faxes are sent
2400 4800 9600 14400 33600
Lets you scan a document that contains mixed paper sizes into a single file
Specifies whether a preview will appear on the display for scan jobs
Adjusts the amount of background visible on a copy

Lets you automatically center the fax on the page
Specifies which color to drop during faxing, and how much to increase or decrease the dropout
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specifies the contrast of the output
Best for content 0–5
Creates a mirror image of the original document
Creates a negative image of the original document
0–4 Adjusts the amount of shadow detail visible on a fax
Scan edge to edge
Specifies if the original document is scanned edge-to-edge prior to faxing
0–5 Adjusts the amount of sharpness on a fax
Enable Color Fax Scans
On by default Never use Always use Off by default
Auto Convert Color Faxes to Mono Faxes
Converts all outgoing faxes to black and white

Allows fax jobs to be received by the printer
1–25 Specifies the number of rings before answering an incoming fax job
Scales an incoming fax job so it fits the size of the paper loaded in the designated fax source
Specifies the paper source selected to supply paper for the printer to print an incoming fax
Auto Tray Multi-Purpose Feeder
Specifies an output bin for received faxes
Standard Bin Bin 1
Enables duplex printing (two-sided printing) for incoming fax jobs
Prints the transmission information at the bottom of each page from a received fax
Specifies the maximum speed in baud at which faxes are received
2400 4800 9600 14400 33600
Enables forwarding of received faxes to another recipient
Forward Print Print and Forward
Specifies the type of recipient to which faxes will be forwarded
Fax E-mail FTP LDSS eSF
Forward to Shortcut Lets you enter the shortcut number which matches the recipient type (Fax, E- mail, FPT, LDSS, or eSF)

Block No Name Fax
Enables blocking of incoming faxes sent from devices with no station ID specified
Banned Fax List Enables the list of banned fax numbers stored in the printer
Enables fax holding all of the time or according to a set schedule
Off Always On Manual Scheduled Fax Holding Schedule
Specifies the default staple setting for the attached finisher
Enables printing of a transmission log after each fax job
Print log Do not print log Print only for error
Enables printing of a receive error log following a receive error
Print Never Print on Error
Enables automatic printing of fax logs
Selects the source of the paper used for printing logs
Tray Manual Feeder
Specifies whether printed logs display the dialed number or the station name returned
Remote Station Name Dialed Number
Enables access to the Fax Job log
Enables access to the Fax Call log

Specifies the output bin where fax logs are printed
Standard Bin Bin
Always Off On until Connected Always On
Controls the volume setting
Controls the fax speaker ringer volume
Answers calls with a one-ring pattern
Answers calls with a double-ring pattern
Answers calls with a triple-ring pattern
Fax Server mode sends the fax job to a fax server for transmission.
To Format Reply Address Subject Message
Lets you enter the information using the virtual keyboard on the printer touch screen

Primary SMTP Gateway Specifies SMTP server port information
Secondary SMTP Gateway Specifies SMTP server port information
Specifies the image type for scan to fax
PDF (.pdf) XPS (.xps) TIFF (.tif)
Specifies the type of content that will be scanned to fax
Specifies the resolution level for scan to fax
Standard Fine Super Fine Ultra Fine
1–9 Lightens or darkens the output
Specifies the orientation of the scanned image

Specifies the paper size of the document that is being scanned
Letter Legal Executive Folio Statement Universal 4 x 6 in. 3 x 5 in. Business Card Custom Scan Size A4 A5 Oficio (Mexico) A6 JIS B5 Book Original Auto Size Sense Mixed Letter/Legal
Provides a choice between single-page TIFF files and multiple-page TIFF files. For a multiple-page scan to fax job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.
Enables analog fax receive
Specifies e-mail server information

Sends a copy of the e-mail back to the creator of the e-mail
Send me a copy
Never appears On by default Off by default Always On
Specifies the maximum e-mail size in kilobytes
Sends a message when an e-mail is greater than the configured size limit
Sends an e-mail only when the address contains the domain name, such as a company domain name
Defines the path name
Server Login Password Path Base file name Web Link
Specifies the format of the file
PDF (.pdf) Secure PDF TIFF (.tif) JPEG (.jpg) XPS (.xps)
1.2–1.6 Sets the version of the PDF file that will be scanned to e-mail
Specifies the type of content that will be scanned to e-mail

Specifies whether a job prints in grayscale or color
Specifies how many dots per inch are scanned
75 150 200 300 400 600
1–9 Lightens or darkens the output
Specifies the orientation of the scanned image
Specifies the paper size of the document that is being scanned
Letter Legal Executive Folio Statement Universal 4 x 6 in. 3 x 5 in. Business Card Custom Scan Size A4 A5 Oficio (Mexico) A6 JIS B5 Book Original Auto Size Sense Mixed Letter/Legal
Specifies how the text and graphics are oriented on the page
Off Long edge Short edge

Sets the quality of a JPEG photo image in relation to file size and the quality of the image
Best for content 5–90
E-mail images sent as
Specifies how the images will be sent
Provides a choice between single-page TIFF files and multiple-page TIFF files. For a multiple-page scan to e-mail job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.
Specifies whether the transmission log prints
Print log Do not print log Print only for error
Specifies a paper source for printing e-mail logs
Tray Manual Feeder Manual Env MP Feeder
Specifies an output bin for the printed e-mail log
Standard Bin Bin
Enables the Text/Photo mode to have smaller file sizes by using 1-bit images when Color is set to Off.
8 bit 1 bit
Lets you copy a document that contains mixed paper sizes into a single job
Specifies whether a preview will appear on the display for scan jobs

Allow Save as Shortcut
Lets you save e-mail addresses as shortcuts
Adjusts the amount of background visible on a scanned image
Lets you automatically center the copy on the page
Specifies which color to drop during scanning, and how much to increase or decrease the dropout
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specifies the contrast of the output
0–5 Best for content
Creates a mirror image of the original document
Creates a negative image of the original document
0–4 Adjusts the amount of shadow detail visible on a scanned image
Scan edge to edge
Specifies whether the original document is scanned edge-to-edge
0–5 Adjusts the amount of sharpness on a scanned image

Use cc:/bcc:
Enables the use of the cc: and bcc: fields
Specifies the format of the FTP file
PDF (.pdf) Secure PDF TIFF (.tif) JPEG (.jpg) XPS (.xps)
1.2–1.6 Sets the version level of the PDF file for FTP
Specifies the type of content that will be scanned to FTP
Specifies whether a job prints in grayscale or color
Specifies how many dots per inch are scanned
75 150 200 300 400 600
1–9 Lightens or darkens the output
Specifies the orientation of the scanned image

Specifies the paper size of the document that is being scanned
Letter Legal Executive Folio Statement Universal 4 x 6 in. 3 x 5 in. Business Card Custom Scan Size A4 A5 Oficio (Mexico) A6 JIS B5 Book Original Auto Size Sense Mixed Letter/Legal
Specifies how the text and graphics are oriented on the page
Off Long edge Short edge
Sets the quality of a JPEG photo image in relation to file size and the quality of the image
Best for content 5–90
Provides a choice between single-page TIFF files and multiple-page TIFF files. For a multiple-page scan to FTP job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.

Specifies whether the transmission log prints
Print log Do not print log Print only for error
Specifies a paper source for FTP logs
Tray Manual Feeder Manual Env MP Feeder
Specifies an output bin for the FTP log
Standard Bin Bin
Enables the Text/Photo mode to have smaller file sizes by using 1-bit images when Color is set to Off
8 bit 1 bit
Base File Name Lets you enter a base file name
Lets you copy a document that contains mixed paper sizes into a single job
Specifies whether a preview will appear on the display for scan jobs
Allow Save as Shortcut
Enables shortcut creation for FTP addresses
Adjusts the amount of background visible on a copy
Lets you automatically center the copy on the page

Specifies which color to drop during scanning, and how much to increase or decrease the dropout
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specifies the contrast of the output
0–5 Best for content
Creates a mirror image of the original document
Creates a negative image of the original document
0–4 Adjusts the amount of shadow detail visible on a scanned image
Scan edge to edge
Specifies whether the original document is scanned edge-to-edge
0–5 Adjusts the amount of sharpness on a scanned image
Specifies the format of the file
PDF (.pdf) Secure PDF TIFF (.tif) JPEG (.jpg) XPS (.xps)

1.2–1.6 Sets the version of the PDF file that will be scanned to USB
Specifies the type of content that will be scanned to USB
Specifies whether job prints in grayscale or color
Specifies how many dots per inch are scanned
75 150 200 300 400 600
1–9 Lightens or darkens the output
Specifies the orientation of the scanned image

Specifies the paper size of the document that is being scanned
Letter Legal Executive Folio Statement Universal 4 x 6 in. 3 x 5 in. Business Card Custom Scan Size A4 A5 Oficio (Mexico) A6 JIS B5 Book Original Auto Size Sense Mixed Letter/Legal
Specifies how the text and graphics are oriented on the page
Off Long edge Short edge
5–90 Sets the quality of a JPEG photo image in relation to file size and the quality of the image
Sets the quality of a JPEG text or text/photo image in relation to file size and the quality of the image.
Best for content 5–90

Provides a choice between single-page TIFF files and multiple-page TIFF files. For a multiple-page scan to USB job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.
Enables the Text/Photo mode to have smaller file sizes by using 1-bit images when Color is set to Off
8 bit 1 bit
Base File Name Lets you enter a base file name
Lets you copy a document that contains mixed paper sizes into a single job
Specifies whether a preview will appear on the display for scan jobs
Adjusts the amount of background visible on a copy
Lets you automatically center the copy on the page
Specifies which color to drop during scanning, and how much to increase or decrease the dropout
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specifies the contrast of the output
0–5 Best for content
Creates a mirror image of the original document

Creates a negative image of the original document
0–4 Adjusts the amount of shadow detail visible on a scanned image
Scan edge to edge
Specifies whether the original document is scanned edge-to-edge
0–5 Adjusts the amount of sharpness on a scanned image
Copies Specifies the number of copies to print
Specifies the paper source selected to supply paper for the printer to print from the flash drive
Tray MP Feeder Manual Paper Manual Envelope
Stacks the pages of a print job in sequence when printing multiple copies
Off (1,1,1,2,2,2) On (1,2,1,2,1,2)
Enables duplex printing (two-sided printing)
Defines the way duplexed pages are bound and how the printing on the back of the page is oriented in relation to the printing on the front of the page
Long Edge Short Edge

Specifies the orientation of the print job
Specifies that multiple-page images be printed on one side of a sheet of paper. This is also referred to as Paper Saver.
Off 2 Up 3 Up 4 Up 6 Up 9 Up 12 Up 16 Up
Prints a border around each page image when using N-up
Specifies the positioning of multiple-page images when using N-up
Horizontal Reverse Horizontal Reverse Vertical Vertical
Places a sheet of paper between pages, copies, or jobs based on the value selected
None Between Copies Between Jobs Between Pages
Specifies a paper source
Tray Manual Feeder Envelope Feeder
Specifies whether blank pages are inserted in a print job
Do Not Print Print

Sets the default printer language
PCL Emulation PS Emulation
Specifies that print jobs be removed from the print queue if they require unavailable printer options or custom settings. They are stored in a separate print queue, so other jobs print normally. When the missing information and/or options are obtained, the stored jobs print.
Sets the logical and physical printable area

Sets the storage location for downloads
Specifies whether the printer stores statistical information about the most recent print jobs on the hard disk
Specifies how the printer handles temporary downloads, such as fonts and macros stored in RAM, when the printer receives a job that requires more memory than is available

Specifies the order in which held and confidential jobs are printed when Print All is selected
Alphabetically Newest First Oldest First
Specifies whether duplex (2-sided) printing is set as the default for all print jobs
2 sided 1 sided
Defines the way duplexed pages are bound and how the printing on the back of the page is oriented in relation to the printing on the front of the page
Long Edge Short Edge
1–999 Specifies a default number of copies for each print job
Specifies whether blank pages are inserted in a print job
Do Not Print Print
Stacks the pages of a print job in sequence when printing multiple copies
Off (1,1,1,2,2,2) On (1,2,1,2,1,2)

Specifies whether blank separator sheets are inserted
None Between Copies Between Jobs Between Pages
Specifies the paper source for separator sheets
Tray Multi-Purpose Feeder Envelope Feeder
Specifies that multiple-page images be printed on one side of a sheet of paper
Off 2-Up 3-Up 4-Up 6-Up 9-Up 12-Up 16-Up
Specifies the positioning of multiple-page images when using N-up (pages-sides)
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specifies the orientation of a multiple-page sheet
Prints a border around each page image when using N-up (pages-sides)

Specifies whether print jobs are stapled
Stacks copies or print jobs into staggered sets in an output bin
Off Between Jobs Between Copies
Specifies the printed output resolution
300 dpi 600 dpi 1200 dpi 1200 Image Q 2400 Image Q
Enhances the printed quality of small fonts and graphics
Off Fonts Horizontally Vertically Both Directions
1–10 Lightens or darkens the printed output
Enables a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts

Adjusts the gray value of printed output
Adjusts or darkens printed output and conserves toner
0–5 Adjusts the degree of difference between levels of gray in printed output
Removes confidential and held jobs from the printer hard disk
Confidential Held Not Restored All
Formats the flash memory. Flash memory refers to the memory added by installing a flash memory option card in the printer.
Delete Downloads on Disk
Removes downloads from the printer hard disk, including all held Jobs, buffered jobs, and parked jobs. Job accounting information is not affected.
Delete Now Do Not Delete

Prints a list of all stored job statistics or deletes the information from the printer hard disk
Assists in isolating the source of a print job problem
Provides an estimate of the percentage coverage of black on a page. The estimate is printed on a separate page at the end of each print job.
1–10 Adjusts the contrast lighting of the display
1–10 Adjusts the brightness of the backlight on the display
Scales page content to fit the selected paper size
Prints annotations in a PDF
Do Not Print Print

Prints a page containing the PostScript error
Establishes the font search order
Specifies the set of fonts used by the Font Name menu item
Resident Disk Download Flash All
Identifies a specific font and the option where it is stored

Specifies the symbol set for each font name
Specifies the font pitch for scalable monospaced fonts
0.08–100
Specifies the orientation of text and graphics on the page
Specifies the number of lines that print on each page
Sets the printer to print on A4-size paper
198 mm 203 mm
Specifies whether the printer automatically performs a carriage return after a line feed control command
Auto CR after LF

Specifies whether the printer automatically performs a line feed after a carriage return control command
Auto LF after CR
Configures the printer to work with printer software or programs that use different source assignments for trays, drawers, and feeders
Off None 0–199 Assign Tray
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Man Env
Lets you view the factory default setting assigned to each tray, drawer, or feeder, even if it has not been installed
MPF Default = 8 T1 Default = 1 T2 Default = 4 T3 Default = 5 T4 Default = 20 T5 Default = 21 Env Default = 6 MPaper Default = 2 MEnv Default = 3
Returns all tray, drawer, and feeder assignments to the factory default settings

Intl CG Times Intl Courier Intl Univers Joanna MT Letter Gothic Lubalin Gothic Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery
Sets the default font for HTML documents
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text
1–255 pt Sets the default font size for HTML documents
1–400% Scales the default font for HTML documents
Sets the page orientation for HTML documents
8–255 mm Sets the page margin for HTML documents

Specifies whether to print backgrounds on HTML documents
Do Not Print Print
Selects the optimal paper size, scaling, and orientation
Inverts bi-tonal monochrome images
Scales the image to fit the selected paper size
Anchor Top Left Best Fit Anchor Center Fit Height/Width Fit Height Fit Width
Sets the image orientation
Portrait Landscape Rev Portrait Rev Landscape
Prints a page containing information on errors, including XML markup errors

The Help menu consists of Help pages that are stored in the printer as PDFs. They contain reference information about using the printer and performing tasks. You may select to print each one individually, or select Print all guides to print all of them at one time.
English, French, German, and Spanish translations are stored in the printer. Other translations are available on the Software and Documentation CD.
Print all guides Prints all the guides
Copy guide Provides information about making copies and changing settings
E-mail guide Provides information about sending e-mails using addresses, shortcut numbers, or the address book, and changing settings
Fax guide Provides information about sending faxes using fax numbers, shortcut numbers, or the address book, and changing settings
FTP guide Provides information about scanning documents directly to an FTP server using an FTP address, shortcut numbers, or the address book, and changing settings
Information guide Provides help in locating additional information
Print defects guide Provides help in resolving repeating defects in copies or prints
Supplies guide Provides part numbers for ordering supplies
Menu item Description · Understanding printer menus

List of status and error messages
The printer is answering a fax call. Wait for the message to clear.
Wait for the message to clear.
A fax call is completed. Wait for the message to clear.
is a tray or feeder, and is a paper size or type.
You can change the current paper source for the remainder of the print job. The formatted page will print on the paper loaded in the selected tray. This may cause clipping of text or images. Try one or more of the following:
Try one or more of the following:
If the error occurs a second time:
1 Turn the printer off. 2 Unplug the power cord from the wall outlet. 3 Remove the tray. 4 Reattach the tray. 5 Connect the power cord to a properly grounded outlet. 6 Restart the printer.
If the error occurs again:
1 Turn the printer off. 2 Unplug the power cord from the wall outlet.
Understanding printer messages

3 Remove the tray. 4 Contact Customer Support. • Touch Continue to clear the message and print without using the tray.
The cartridge is missing or not installed correctly. Insert the cartridge and close all doors and covers.
Close the side door on the finisher.
The fax is connected. Wait for the message to clear.
A fax number is dialed. If the number is too long to fit on the screen, only the word Dialing appears. Wait for the message to clear.
The printer attempted a hard disk recovery on a corrupted hard disk, and the hard disk cannot be repaired. The hard disk must be reformatted.
Touch Reformat disk to reformat the hard disk and clear the message.
The scan job canceled or stopped due to insufficient printer hard disk space.
Touch Continue to clear the message.
The fax failed to be sent. Wait for the message to clear.
There is not enough memory to send the fax job.
Touch Continue to clear the message.
Understanding printer messages

Fax partition inoperative. Contact system administrator.
The fax partition appears to be corrupted. Try one or more of the following:
Fax server 'To Format' not set up. Contact system administrator.
The printer is in Fax Server mode, but the Fax Server setup has not been completed.
Try one or more of the following:
The Fax Station Name has not been entered. Sending and receiving faxes is disabled until fax is configured properly.
Try one or more of the following:
The Fax Station Number has not been entered. Sending and receiving faxes is disabled until fax is configured properly.
Try one or more of the following:
Wait for the message to clear.
Try one or more of the following:
Insert the specified tray into the printer.
Understanding printer messages

Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Enter a valid PIN.
The scanning completed for a delayed send fax job. Wait for the message to clear.
A fax number is dialed, but the fax line is busy. Wait for the message to clear.
Understanding printer messages

is a tray or feeder, and is a paper type or size.
Try one or more of the following:
If the printer finds a tray that has the correct paper type and size, it feeds from that tray. If the printer cannot find a tray with the correct paper type and size, it prints from the default source. • Cancel the current job.
is a paper type or size.
Try one or more of the following:
If the printer finds a tray that has the correct paper type and size, then it feeds from that tray. If the printer cannot find a tray with the correct paper type and size, then it prints from the default source. • Cancel the current job.
Try one or more of the following:
There is not enough memory to print the fax job.
Touch Continue to clear the message without printing. Held faxes will attempt to print after the printer has been restarted.
The printer is connected to the network.
Network indicates that the printer is using the standard network port built into the printer system board. Network <x> indicates that an internal print server is installed inside the printer or that the printer is connected to an external print server.
No analog phone line connected to modem, fax is disabled.
The printer is not detecting an analog phone line, so the fax is disabled. Connect the printer to an analog phone line.
Understanding printer messages

A fax number is dialed, but no connection is made. Wait for the message to clear.
The printer does not have a dial tone. Wait for the message to clear.
The scanning process of a fax job completed, but the job is not sent yet because another fax job is being sent or received. Wait for the message to clear.
The printer is ready to receive print jobs.
Try one or more of the following:
If the error occurs a second time:
1 Turn the printer off. 2 Unplug the power cord from the wall outlet. 3 Remove the specified bin. 4 Reattach the bin. 5 Connect the power cord to a properly grounded outlet. 6 Restart the printer.
If the error occurs again:
1 Turn the printer off. 2 Unplug the power cord from the wall outlet. 3 Remove the specified bin. 4 Contact Customer Support. • Touch Continue to clear the message and print without using the specified bin.
Try one or more of the following:
If the error occurs a second time:
1 Turn the printer off. 2 Unplug the power cord from the wall outlet. 3 Remove the specified bins. 4 Reattach the bins.
Understanding printer messages

5 Connect the power cord to a properly grounded outlet. 6 Restart the printer.
If the error occurs again:
1 Turn the printer off. 2 Unplug the power cord from the wall outlet. 3 Remove the specified bins. 4 Contact Customer Support. • Touch Continue to clear the message and print without using the specified bins.
Try one or more of the following:
If the error occurs a second time:
1 Turn the printer off. 2 Unplug the power cord from the wall outlet. 3 Remove the envelope feeder. 4 Reattach the envelope feeder. 5 Connect the power cord to a properly grounded outlet. 6 Restart the printer.
If the error occurs again:
1 Turn the printer off. 2 Unplug the power cord from the wall outlet. 3 Remove the envelope feeder. 4 Contact Customer Support. • Touch Continue to clear the message and print without using the envelope feeder.
The printer has received an entire fax job. Wait for the message to clear.
The printer receives page of the fax job, where is the number of the page received. Wait for the message to clear.
Remove any remaining packaging material from the specified location.
Remove the paper from the specified bin. The printer automatically senses paper removal and resumes printing.
Understanding printer messages

If removing the paper does not clear the message, then touch Continue.
Remove the paper from all of the bins. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Remove the paper from the specified bin. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Remove the stack of paper from the standard exit bin.
Replace <x> if restarting job.
One or more messages which interrupted a scan job are now cleared. Replace the original documents in the scanner to restart the scan job. is a page of the scan job.
Try one or more of the following:
Replace the fuser wiper, or try one or more of the following:
Try one or more of the following:
Understanding printer messages

The scan job exceeds the maximum number of pages. Touch Cancel Job to clear the message.
The ADF cover is open. The message clears when the cover is closed.
Close the bottom ADF door to clear the message.
The printer hard disk wiping process needs to recover. The message clears when all blocks are cleared.
The printer sends page of the fax job, where is the number of the page sent. Wait for the message to clear.
The printer is using a serial cable connection. The serial port is the active communication link.
The clock is not set. This message appears if no other fax status message appears. It remains until the clock is set.
SMTP server not set up. Contact system administrator.
An error occurred on the SMTP server, or the SMTP server is not configured properly. Touch Continue to clear the message. If the message appears again, contact your system support person.
Touch Continue to delete the specified job.
System busy, preparing resources for job.
Not all resources needed for the job are available. Wait for the message to clear.
System busy, preparing resources for job. Deleting held job(s).
Not all resources needed for the job are available. Some held jobs are deleted to free system memory. Wait for the message to clear.
An unsupported printer hard disk has been installed. Remove the unsupported device, and then install a supported one.
Understanding printer messages

Remove the unrecognized USB device.
Remove the unrecognized USB hub.
The printer is using a USB cable connection. The USB port is the active communication link.
The printer is waiting to redial the fax number. Wait for the message to clear.
Remove the print cartridge, and then install a supported one.
Remove the defective print cartridge, and then install a new one.
Remove the print cartridge, and then install a supported one.
Try one or more of the following:
Try one or more of the following:
Understanding printer messages

Try one or more of the following:
Try one or more of the following:
The printer deleted some held jobs in order to process current jobs.
Touch Continue to clear the message.
The printer was unable to restore some or all of the confidential or held jobs on the printer hard disk.
Touch Continue to clear the message.
Try one or more of the following:
Try one or more of the following:
Install a print cartridge that matches the region number of the printer. x indicates the value of the printer region. y indicates the value of the cartridge region. x and y can have the following values:
2 Europe, the Middle East, and Africa
3 Asia · 4 Latin America · Understanding printer messages

Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
is the number of the network connection.
Try one or more of the following:
is the number of the serial option.
Try one or more of the following:
9 Invalid region · Understanding printer messages

Try one or more of the following:
is a slot on the printer system board.
Try one or more of the following:
1 Turn the printer power off.
2 Unplug the power cord from the wall outlet.
3 Remove the unsupported option card from the printer system board.
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer power back on.
is the number of the parallel port.
Try one or more of the following:
The printer discards any data received through the parallel port. • Make sure the Parallel Buffer menu item is not set to Disabled.
is the number of the serial port.
Try one or more of the following:
The printer discards any data received through the serial port. • Make sure the Serial Buffer menu item is not set to Disabled.
Try one or more of the following:
The printer discards any data received through the parallel port. • Make sure the Parallel Buffer menu item is not set to Disabled.
Understanding printer messages

Try one or more of the following:
The printer discards any data received through the USB port. • Make sure the USB Buffer menu item is not set to Disabled.
is the number of the USB port.
Try one or more of the following:
The printer discards any data received through the USB port. • Make sure the USB Buffer menu item is not set to Disabled.
Since the time the jobs were stored on the printer hard disk something has changed in the printer to invalidate the held jobs. Possible changes include:
Touch Continue to clear the message.
1 Turn the printer power off.
2 Unplug the power cord from the wall outlet.
3 Remove the additional bins.
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer power back on.
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Remove the extra disks.
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer back on.
Understanding printer messages

1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Remove the excess flash memory.
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer back on.
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Remove the additional trays.
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer back on.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Understanding printer messages

Try one or more of the following:
Try one or more of the following:
If the error message remains, the hard disk may be defective and require replacing.
The printer needs to have routine maintenance done. Order a maintenance kit, which contains all the items necessary to replace the pick rollers, the charge roll, the transfer roller, and the fuser.
The toner is low. Replace the print cartridge, and then touch Continue to clear the message and continue printing.
The toner is low. Replace the print cartridge, and then touch Continue to clear the message and continue printing.
The print cartridge is empty.
1 Replace the print cartridge.
2 Touch Continue to clear the message.
1 Clear the paper path.
2 Touch Continue to continue printing.
1 Clear the jam from the specified stapler area(s).
2 Touch Continue to continue printing.
Clear all original documents from the scanner.
Understanding printer messages

293 Replace all originals if restarting job.
The scanner was instructed to scan using the ADF but there is no paper in the ADF. Load paper in the ADF.
Try one or more of the following:
Close the scanner cover.
This message indicates that the scanner has been disabled by the system support person.
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Check all cable connections.
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer back on.
If the service message appears again, then contact Customer Support, and report the message.
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Check all cable connections.
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer back on.
If the service message appears again, contact Customer Support, and report the message.
Understanding printer messages

The printer automatically clears the message in 30 seconds and then disables the download emulator on the firmware card.
To fix this, download the correct download emulator version from the Lexmark Web site at www.lexmark.com.
Understanding printer messages

Periodically, certain tasks are required to maintain optimum print quality.
1 Make sure that the printer is turned off and unplugged from the wall outlet.
2 Remove paper from the standard exit bin.
3 Dampen a clean, lint-free cloth with water.
4 Wipe only the outside of the printer, making sure to include the standard exit bin.
5 Make sure the paper support and standard exit bin are dry before beginning a new print job.
Clean the scanner glass if you encounter print quality problems, such as streaks on copied or scanned images.
1 Slightly dampen a soft, lint-free cloth or paper towel with water.
2 Open the scanner cover.

Maintaining the printer

3 Wipe the scanner glass until it is clean and dry.
4 Wipe the white underside of the scanner cover until it is clean and dry.
5 Open the bottom ADF door.

6 Wipe the ADF scanner glass under the ADF door.
7 Close the bottom ADF door.
8 Wipe the scanner glass (flatbed) and backing material by moving the cloth or paper towel from side to side.
9 Close the scanner cover.
Scanner Registration is a process to align the scan area with the paper location. To manually adjust the scanner registration:
1 Turn the printer off.
2 Clean the scanner glass and backing material.
3 Hold down 2 ABC and
6 MNO while turning the printer on.
4 Release the buttons when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears.
5 Touch the down arrow until Scanner Manual Registration appears.
6 Touch Scanner Manual Registration.
7 Touch Print Quick Test to print a registration page.
8 Choose the section of the scanner to align.
Maintaining the printer

To align the scanner glass (flatbed):
a Place the Quick Test page facedown on the scanner glass.

b Touch Copy Quick Test.
The scanner prints a copy of the Quick Test page. c Touch Flatbed. d Use the copy of the Quick Test page to adjust the Left Margin and Top Margin settings. e Touch Submit.
f Touch Copy Quick Test and compare the new copy to the original. Repeat the flatbed alignment steps until the position on the page of the Quick Test copy closely matches the original.
To align the ADF:
a Do one of the following:
The scanner prints a copy of the Quick Test page. c Touch ADF Front or ADF Back. d Use the copy of the Quick Test page to adjust the Horizontal Adjust and Top Margin settings. e Touch Submit.
f Touch Copy Quick Test and compare the new copy to the original. Repeat the ADF alignment steps until the position on the page of the Quick Test copy closely matches the original.
9 Touch Back.
10 Touch Exit Configuration.
Maintaining the printer

Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:
There are some settings you can change from the printer control panel that will help you conserve toner and paper. For more information, see “Supplies menu,” “Quality menu,” and “Finishing menu.”
If you need to print several copies, you can conserve supplies by printing the first copy and checking it for accuracy before printing the remaining copies.
A message appears on the display when a replacement supply item is needed or when maintenance is required.
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch Status/Supplies.
1 Type the printer IP address into the address field of your Web browser.
2 Click Device Status. The Device Status page appears, displaying a summary of supply levels.
Maintaining the printer

To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, visit the Lexmark Web Site at www.lexmark.com or contact the place where you purchased the printer.
When 88 Cartridge low appears or when the print becomes faded, you may be able to extend the life of the print cartridge:
1 Remove the print cartridge.
2 Firmly shake the cartridge side-to-side and front-to-back several times to redistribute toner.
3 Reinsert the cartridge and continue printing.

High Yield Return Program Print Cartridge for Label Applications
Extra High Yield Return Program Print Cartridge for Label Applications
High Yield Return Program Print Cartridge for Label Applications
Maintaining the printer

Part name Lexmark Return Program Cartridge Regular cartridge
Extra High Yield Return Program Print Cartridge for Label Applications
For the Asia Pacific Region, including Australia and New Zealand
Print cartridge X651A21P X651A11P
High Yield Print Cartridge X651H21P X651H11P
Extra High Yield Print Cartridge X654X21P X654X11P
High Yield Return Program Print Cartridge for Label Applications
Extra High Yield Return Program Print Cartridge for Label Applications
Print cartridge X651A21L X651A11L
High Yield Print Cartridge X651H21L X651H11L
Extra High Yield Print Cartridge X654X21L X654X11L
High Yield Return Program Print Cartridge for Label Applications
Extra High Yield Return Program Print Cartridge for Label Applications
When 80 Routine maintenance needed appears, order a maintenance kit. The maintenance kit contains all the items necessary to replace the pick rollers, the charge roll, the transfer roller, and the fuser.
Part name Part number
Maintenance kit 40X4723 (100 V T1 fuser) 40X4724 (110 V T1 fuser) 40X4765 (220 V T1 fuser) 40X4766 (100 V T2 fuser) 40X4767 (110 V T2 fuser) 40X4768 (220 V T2 fuser)

To check the fuser type (T1 or T2) installed in the printer, remove the print cartridge to view the label on the fuser.
Part name Part number
T1 fuser 40X1870 (100 V) 40X4418 (110 V) 40X1871 (220 V)
T2 fuser 40X1872 (100 V) 40X1873 (110 V) 40X1874 (220 V)
The ADF maintenance kit contains all the items necessary to replace the ADF pick mechanism and the ADF separator roller.
See the following table for the maintenance kit part number for your specific printer.
Part name Part number
ADF Maintenance kit 40X4769
When toner smudges appear on the front or back of printed pages, order a replacement transfer roller.
Part name Part number
Transfer roll assembly 40X1886
When toner fog or background shading appears on printed pages, order replacement charge rolls.
Part name Part number
Charge roll assembly 40X5852
When the paper fails to properly feed from the tray, order new pick rollers.
Part name Part number
Pick rollers 40X4308 · Maintaining the printer

Order ADF replacement parts if you experience problems with paper double-feeding or failing to feed through the automatic document feeder.
Part name Part number
ADF pick assembly 3017345
ADF separator roll 3017348
When Staples Low or Staples Empty appears, order the specified staple cartridge.
For more information, see the illustrations inside the stapler door.
Part name Part number
Staple Cartridges–3 pack 25A0013
To return Lexmark products to Lexmark for recycling:
1 Visit our Web site at www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country from the list.
3 Follow the instructions on the computer screen.
Maintaining the printer


– Remove all printer options before moving the printer. – Use the handholds located on both sides of the printer to lift it off the optional drawer.
The printer and options can be safely moved to another location by following these precautions:
Allow the following recommended amount of space around the printer:
Maintaining the printer


1 Right Side 20 cm (8 in.)
2 Left Side 31 cm (12 in.)
3 Front 51 cm (20 in.)
4 Rear 20 cm (8 in.)
5 Top 31 cm (12 in.)
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.
Maintaining the printer

Finding advanced networking and administrator information
This chapter covers basic administrative support tasks. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD and the Embedded Web Server Administrator's Guide on the Lexmark Web site at www.lexmark.com
If the printer is installed on a network, the Embedded Web Server is available for a range of functions including:
To access the Embedded Web Server, type the printer IP address into the address field of your Web browser.
Using the Embedded Web Server, you can view paper tray settings, the level of toner in the print cartridge, the percentage of life remaining in the maintenance kit, and capacity measurements of certain printer parts. To view the device status:
1 Type the printer IP address in the address field of your Web browser.
2 Click Device Status.
You can have the printer send you an e-mail when the supplies are getting low or when the paper needs to be changed, added, or unjammed.
Administrative support

To set up e-mail alerts:
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Under Other Settings, click E-mail Alert Setup.
4 Select the items for notification, and type in the e-mail addresses.
5 Click Submit.
You can view some reports from the Embedded Web Server. These reports are useful for assessing the status of the printer, the network, and supplies.
To view reports from a network printer:
1 Type the printer IP address into the address field of your Web browser.
2 Click Reports, and then click the type of report you want to view.
If you are having trouble reading your display, the LCD brightness can be adjusted through the Settings menu.
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch
3 Touch Settings.
4 Touch General Settings.
5 Touch the down arrow until Screen Brightness appears.
6 Touch the arrows to increase or decrease the brightness.
Brightness settings can be adjusted from 20–100 (100 is the factory default setting).
7 Touch Submit.
8 Touch · Administrative support

Available settings range from 1–240 minutes. The factory default is 30 minutes.
To increase or decrease the number of minutes before the printer enters Power Saver mode, do one of the following:
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings, and then click General Settings.
3 Click Timeouts.
4 In the Power Saver box, increase or decrease the number of minutes you want the printer to wait before it enters Power Saver mode.
5 Click Submit.
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch
3 Touch Settings.
4 Touch General Settings.
5 Touch the down arrow until Timeouts appears.
6 Touch Timeouts.
7 Touch the left or right arrow next to Power Saver Mode to decrease or increase the time the printer waits before entering Power Saver mode.
The settings available range from 1–240 minutes.
8 Touch Submit.
If you want to retain a list of the current menu settings for reference, then print a menu settings page before you restore the factory default settings. For more information, see “Printing a menu settings page” on page 45.
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch
3 Touch Settings.
9 Touch · Administrative support

4 Touch General Settings.
5 Touch the down arrow until Factory Defaults appears.
6 Touch the left or right arrow until Restore Now appears.
7 Touch Submit.
8 Touch · Administrative support

Solving basic printer problems
If there are basic printer problems, or the printer is unresponsive, make sure:
Once you have checked each of these possibilities, turn the printer off, wait for about 10 seconds, and then turn the printer back on. This often fixes the problem.
The printer self test failed. Turn the printer off, wait about 10 seconds, and then turn the printer on.
If Ready does not appear, then turn the printer off and contact Customer Support.
The documents contain unavailable fonts.
1 Open the document you want to print in Adobe Acrobat.
2 Click the printer icon.
The Print dialog appears.
3 Select Print as image.
4 Click OK.
Make sure the USB drive is supported. For information regarding tested and approved USB flash memory devices, visit the Lexmark Web site at www.lexmark.com.
Troubleshooting

These are possible solutions. Try one or more of the following:
Make sure Ready or Power Saver appears on the display before sending a job to print.
Remove the stack of paper from the standard exit bin.
Load paper in the tray.
Copies of the printer software are also available on the Lexmark Web site at www.lexmark.com.
MAKE SURE YOU ARE USING A RECOMMENDED USB, SERIAL, OR ETHERNET CABLE
For more information, visit the Lexmark Web site at www.lexmark.com.
Check the cable connections to the printer and print server to make sure they are secure.
For more information, see the setup documentation that came with the printer.
These are possible solutions. Try one or more of the following:
The print job may contain a formatting error or invalid data.
Troubleshooting

Free up additional printer memory by scrolling through the list of held jobs and deleting some of them.
These are possible solutions. Try one or more of the following:
Eliminate the number and size of fonts, the number and complexity of images, and the number of pages in the job.
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch
3 Touch Settings.
4 Touch General Settings.
5 Touch the down arrow until Print Recovery appears.
6 Touch Print Recovery.
7 Touch the right arrow next to Page Protect until Off appears.
8 Touch Submit.
C HECK THE PAPER TYPE SETTING
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Type setting from the Paper menu.
MAKE SURE THE PRINTER IS NOT IN HEX TRACE MODE
If Ready Hex appears on the display, then you must exit Hex Trace mode before you can print your job. Turn the printer off and back on to exit Hex Trace mode.
9 Touch · Troubleshooting

These are possible solutions. Try one or more of the following:
USE THE SAME PAPER SIZE AND PAPER TYPE SETTINGS
These are possible solutions. Try one or more of the following:
From the Finishing menu or Print Properties, set Collate to On.
Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Add printer memory or an optional hard disk.
I NCREASE THE P RINT T IMEOUT VALUE
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch
3 Touch Settings.
4 Touch General Settings.
5 Touch the down arrow until Timeouts appears.
6 Touch Timeouts.
7 Touch the left or right arrow next to Print Timeout until the desired value appears.
Troubleshooting

8 Touch Submit.
These are possible solutions. Try one or more of the following:
Clear any error messages.
Make sure the printer is plugged in, the power is on, and Ready appears.
Make sure there are no obstructions:
1 Lift the scanner unit.
2 Remove any obstruction keeping the scanner unit open.
3 Lower the scanner unit.
These are some examples of poor copy quality:
These are possible solutions. Try one or more of the following:
Clear any error messages.
9 Touch · Troubleshooting

When 88 Cartridge low appears or when the print becomes faded, replace the print cartridge.
Clean the scanner glass with a clean, lint-free cloth dampened with water. For more information, see “Cleaning the scanner glass” on page 252.
Adjust the density of the copy.
Make sure the quality of the original document is satisfactory.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Troubleshooting

These are possible solutions. Try one or more of the following:
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Size setting from the Paper menu.
If your scanner is not responding, then make sure:
Once you have checked each of these possibilities, turn the printer off and then back on. This often fixes the problem with the scanner.
These are possible solutions. Try one or more of the following:
Make sure the network or USB cable is securely connected to the computer and the printer.
Turn off and then restart the computer.
Troubleshooting

These are possible solutions. Try one or more of the following:
Close all programs not being used.
Select a lower scan resolution.
These are possible solutions. Try one or more of the following:
Clear any error messages.
Clean the scanner glass with a clean, lint-free cloth dampened with water. For more information, see “Cleaning the scanner glass” on page 252.
Increase the resolution of the scan for a higher quality output.
Make sure the quality of the original document is satisfactory.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
These are possible solutions. Try one or more of the following:
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Troubleshooting

Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Size setting from the Paper menu.
These are possible solutions. Try one or more of the following:
Clear any error messages.
Make sure the printer is plugged in, the power is on, and Ready appears.
Make sure the network or USB cable is securely connected to the computer and the printer.
Contact your telecommunications company to verify that your telephone line is subscribed to the caller ID service.
If your region supports multiple caller ID patterns, you may have to change the default setting. There are two settings available: FSK (pattern 1) and DTMF (pattern 2). The availability of these settings by way of the Fax menu depends on whether your country or region supports multiple caller ID patterns. Contact your telecommunications company to determine which pattern or switch setting to use.
These are possible solutions. Try one or more of the following:
Clear any error messages.
Make sure the printer is plugged in, the power is on, and Ready appears.
Troubleshooting

Make sure the cable connections for the following hardware are secure, if applicable:
1 Plug a telephone into the wall jack.
2 Listen for a dial tone.
3 If you do not hear a dial tone, then plug a different telephone into the wall jack.
4 If you still do not hear a dial tone, then plug a telephone into a different wall jack.
5 If you hear a dial tone, then connect the printer to that wall jack.
The fax modem is an analog device. Certain devices can be connected to the printer so that digital telephone services can be used.
To ensure the printer is working correctly, connect it directly to the telephone line. Disconnect any answering machines, computers with modems, or telephone line splitters.
Clear any jams, and then make sure that Ready appears.
Troubleshooting

Call Waiting can disrupt fax transmissions. Disable this feature before sending or receiving a fax. Call your telephone company to obtain the keypad sequence for temporarily disabling Call Waiting.
Voice Mail offered through your local telephone company may disrupt fax transmissions. To enable both Voice Mail and the printer to answer calls, you may want to consider adding a second telephone line for the printer.
1 Dial the fax number.
2 Scan the original document one page at a time.
These are possible solutions. Try one or more of the following:
Load paper in the tray.
The ring count delay sets the number of times the phone line rings before the printer answers. If you have extension phones on the same line as the printer, or subscribe to the telephone company's Distinctive Ring service, then keep the Ring Delay setting at 4.
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Click Fax Settings.
4 Click Analog Fax Setup.
5 In the Rings to Answer box, enter the number of times you want the phone to ring before answering.
6 Click Submit.
88 Cartridge low appears when the toner is low.
Troubleshooting

These are possible solutions. Try one or more of the following:
On the home screen, touch Fax to put the printer in Fax mode.
Load the original document faceup, short edge first into the ADF or facedown on the scanner glass in the upper left corner.
These are possible solutions. Try one or more of the following:
Ask the person who sent you the fax to:
When 88 Cartridge low appears or when you experience faded print, replace the cartridge.
Decrease the incoming fax transmission speed:
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings.
3 Click Fax Settings.
4 Click Analog Fax Setup.
Troubleshooting

5 In the Max Speed box, click on one of the following: 2400 4800 9600 14400 33600
6 Click Submit.
These are possible solutions. Try one or more of the following:
Turn the printer off, wait about 10 seconds, and then turn the printer on.
1 Turn the printer off.
2 Unplug the printer.
3 Check the connection between the option and the printer.
Print a menu settings page and check to see if the option is listed in the Installed Options list. If the option is not listed, then reinstall it. For more information, see the hardware setup documentation that came with the option, or go to www.lexmark.com/publications to view the option instruction sheet.
From the computer you are printing from, select the option. For more information, see “Updating available options in the printer driver” on page 47.
These are possible solutions. Try one or more of the following:
1 Open the paper tray.
2 Check for paper jams or misfeeds.
3 Make sure paper guides are aligned against the edges of the paper.
4 Make sure the paper tray closes properly.
Troubleshooting

Turn the printer off, wait about 10 seconds, and then turn the printer on.
If the paper tray is listed on the menu settings page, but paper jams when it enters or exits the tray, then it may not be properly installed. Reinstall the paper tray. For more information, see the hardware setup documentation that came with the paper tray, or go to www.lexmark.com/publications to view the paper tray instruction sheet.
These are possible solutions. Try one or more of the following:
These are possible solutions. Try one or more of the following:
Turn the printer off, wait about 10 seconds, and then turn the printer on.
1 Adjust the envelope support for the length of envelope you are using.
2 For more information, see “Loading the envelope feeder” on page 81.
Make sure the paper type and paper size settings match the envelopes you are using:
1 From the printer control panel, check the settings for the envelope feeder from the Paper menu.
Troubleshooting

If the envelope feeder is listed on the menu settings page, but an envelope jams when it enters or exits the feeder, then it may not be properly installed. Reinstall the envelope feeder. For more information, see the hardware setup documentation that came with the envelope feeder, or go to www.lexmark.com/publications to view the envelope feeder instruction sheet.
If the high capacity output expander, 4-bin mailbox, or StapleSmart finisher is listed on the menu settings page, but paper jams when it exits the printer or enters the output option, then it may not be properly installed. Reinstall the option. For more information, see the hardware setup documentation that came with the option.
Make sure the flash memory card is securely connected to the printer system board.
Make sure the hard disk is securely connected to the printer system board.
If the Lexmark Internal Solutions Port (ISP) does not operate correctly, then these are possible solutions. Try one or more of the following:
Make sure you are using the correct cable and that it is securely connected.
For information about installing software for network printing, see the Networking Guide on the Software and Documentation CD
Make sure the memory card is securely connected to the printer system board.
Troubleshooting

These are possible solutions. Try one or more of the following:
Use recommended paper and specialty media. For more information, see the chapter about paper and specialty media guidelines.
MAKE SURE THERE IS NOT TOO MUCH PAPER IN THE PAPER TRAY
Make sure the stack of paper you load does not exceed the maximum stack height indicated in the tray or on the multipurpose feeder.
Move the guides in the tray to the correct positions for the paper size loaded.
C HECK THE PAPER PATH
The paper path is not clear. Clear jammed paper from the entire paper path, and then touch Continue.
T URN ON J AM R ECOVERY
In the Setup menu, Jam Recovery is set to Off. Set Jam Recovery to Auto or On:
1 Make sure the printer is on and Ready appears.
2 On the home screen, touch
3 Touch Settings.
4 Touch General Settings.
5 Touch the down arrow until Print Recovery appears.
6 Touch Print Recovery.
7 Touch the right arrow next to Jam Recovery until On or Auto appears.
Troubleshooting

8 Touch Submit.
The information in the following topics may help you solve print quality problems. If these suggestions still do not correct the problem, contact Customer Support. You may have a printer part that requires adjustment or replacement.
To help isolate print quality problems, print the print quality test pages:
1 Turn the printer off.
2 Load Letter- or A4-size paper in the tray.
3 Hold down 2 ABC and
6 MNO while turning the printer on.
4 Release the buttons when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears.
5 Touch the down arrow until Print Quality Pages appears.
6 Touch Print Quality Pages.
The print quality test pages print.
7 Touch Back.
8 Touch Exit Configuration.
These are possible solutions. Try one or more of the following:
Remove the print cartridge and make sure the packing material is properly removed. Reinstall the print cartridge.
When 88 Cartridge low appears, order a new print cartridge.
If the problem continues, the printer may need to be serviced. For more information, contact Customer Support.
9 Touch · Troubleshooting

These are possible solutions. Try one or more of the following:
If you are using downloaded fonts, then verify that the fonts are supported by the printer, the host computer, and the software program.
These are possible solutions. Try one or more of the following:
Move the width and length guides in the tray to the correct positions for the paper size loaded.
Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Size setting from the Paper menu.
ABCDE ABCDE ABCDE ABCDE ABCDE
ABCDE
Troubleshooting

Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Type setting from the Paper menu.
ABCDE
ABCDE ABCDE
C HECK THE T ONER D ARKNESS SETTING
Select a lighter Toner Darkness setting:
These are possible solutions. Try one or more of the following:
Move the guides in the tray to the correct positions for the paper size loaded.
Troubleshooting

Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Size setting from the Paper menu.
These are possible solutions. Try one or more of the following:
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Type setting from the Paper menu.
These are possible solutions. Try one or more of the following:
Troubleshooting

Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Type setting from the Paper menu.
Avoid textured paper with rough finishes.
When 88 Cartridge low appears or when the print becomes faded, replace the print cartridge.
Replace the fuser.
R EPEATING MARKS OCCUR EVENLY DOWN THE PAGE
Replace the charge rolls if the defects occur every 28.3 mm (1.11 in.).
Replace the transfer roller if the defects occur every 51.7 mm (2.04 in.).
Replace the print cartridge if the defects occur every:
Replace the fuser if the defects occur every:
Troubleshooting

These are possible solutions. Try one or more of the following:
Move the guides in the tray to the correct positions for the paper size loaded.
Make sure you are using paper that meets the printer specifications.
These are possible solutions. Try one or more of the following:
If the fill pattern is incorrect, then choose a different fill pattern from your software program or application.
Remove the print cartridge and shake it from side to side to redistribute the toner, and then reinstall it.
Replace the used print cartridge with a new one.
Troubleshooting

These are possible solutions. Try one or more of the following:
The Toner Darkness setting is too light, the Brightness setting is too light, or the Contrast setting is too low.
Avoid textured paper with rough finishes.
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Type setting from the Paper menu.
When 88 Cartridge Low appears, order a new print cartridge.
Replace the print cartridge.
Troubleshooting

These are possible solutions. Try one or more of the following:
The Toner Darkness setting is too dark, the Brightness setting is too dark, or the Contrast setting is too high.
Avoid textured paper with rough finishes.
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Type setting from the Paper menu.
Replace the print cartridge.
Troubleshooting

These are possible solutions. Try one or more of the following:
Remove the print cartridge and shake it from side to side to redistribute the toner, and then reinstall it.
Replace the used print cartridge with a new one. If the problem continues, the printer may need to be serviced. For more information, contact Customer Support.
ABCDE ABCDE ABCDE
These are possible solutions. Try one or more of the following:
Select another tray or feeder to feed paper for the job:
Replace the print cartridge.
Check the paper path around the print cartridge.
Troubleshooting

Clear any paper you see.
Contact Customer Support.
These are possible solutions. Try one or more of the following:
Replace the print cartridge.
Replace the charge rolls.
Contact Customer Support.
These are possible solutions. Try one or more of the following:
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Type setting from the Paper menu.
From the printer control panel Paper menu, make sure the Paper Texture setting matches the paper loaded in the tray.
Troubleshooting

These are possible solutions. Try one or more of the following:
Replace the print cartridge.
Contact Customer Support.
Try one or more of the following:
Use only transparencies recommended by the printer manufacturer.
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Type setting from the Paper menu.
These are possible solutions. Try one or more of the following:
Make sure the printer and computer are turned on and connected to the same network.
Troubleshooting

Depending on the network settings, you may need to type https:// instead of http:// before the printer IP address to access the Embedded Web Server. For more information, see your system administrator.
When you call Customer Support, describe the problem you are experiencing, the message on the display, and the troubleshooting steps you have already taken to find a solution.
You need to know your printer model type and serial number. For more information, see the label on the inside top front cover of the printer. The serial number is also listed on the menu settings page.
In the U.S. or Canada, call (1-800-539-6275). For other countries/regions, visit the Lexmark Web site at www.lexmark.com.
Troubleshooting

Product name:
Lexmark X651de, Lexmark X652de, Lexmark X654de, Lexmark X656de, Lexmark X656dte, Lexmark X658d, Lexmark X658de, Lexmark X658dme, Lexmark X658dfe, Lexmark X658dte, Lexmark X658dtme, Lexmark X658dtfe
Machine type:
Model(s):
0A1, 0A5, 2A1, 2A2, 2A5, 2A6, 4A2, 4A6, 031, 035, 231, 232, 235, 236, 432, 436
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
If you don't have access to the Internet, you can contact Lexmark by mail:
Lexmark International, Inc. Bldg 004-2/CSC 740 New Circle Road NW Lexington, KY 40550
© 2008 Lexmark International, Inc.
All rights reserved.
This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense.
July 2008

Lexmark, Lexmark with diamond design, MarkNet, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
MarkTrack, PrintCryption, and StapleSmart are trademarks of Lexmark International, Inc.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
The following terms are trademarks or registered trademarks of these companies:

CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation

Univers Linotype-Hell AG and/or its subsidiaries
All other trademarks are the property of their respective owners.
This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
The following notice is applicable if your printer has a wireless network card installed.
The radiated output power of this device is far below the FCC radio frequency exposure limits. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe A est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.

This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.
En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case, the user may be required to take adequate measures.
Industry Canada (Canada) · Industry Canada (Canada)

This product is in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment.
Compliance is indicated by the CE marking.
A declaration of conformity with the requirements of the directives is available from the Director of Manufacturing and Technical Support, Lexmark International, S. A., Boigny, France.
This product satisfies the limits of EN 55022; safety requirements of EN 60950; radio spectrum requirements of ETSI EN 300 330-1 and ETSI EN 300 330-2; and the EMC requirements of EN 55024, ETSI EN 301 489-1 and ETSI EN 301 489-3.
Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.
Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.

Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.
Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky príslušné ustanovenia smernice 1999/5/ES.
Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
This device uses very low power low range RF communication that has been tested and found not to cause any interference whatsoever. The manufacturer is not responsible in case of any disputes arising out of requirement of permissions from any local authority, regulatory bodies or any organization, required by the end-user to install and operate this product at his premises.

The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.

1-meter average sound pressure, dBA
Values are subject to change. See www.lexmark.com for current values.
Ambient temperature 15.6C° – 32.2C°
Shipping and storage temperature -40.0C° – 60.0C°
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products. If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.
information statement
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachments (ACTA). On the back of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to your telephone company.
This equipment uses the RJ-11C Universal Service Order Code (USOC) jack.

A plug and jack used to connect this equipment to the premises’ wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See your setup documentation for more information.
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact your local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (for example, 03 is a REN of 0.3). For earlier products, the REN is shown separately on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. You will also be advised of your right to file a complaint with the FCC.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
If you experience trouble with this equipment, for repair or warranty information, contact Lexmark International, Inc. at www.lexmark.com or your Lexmark representative. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
This equipment contains no user serviceable parts. For repair and warranty information, contact Lexmark International, Inc. See the previous paragraph for contact information.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter's Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless said message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)
See your user documentation in order to program this information into your fax machine.

This product meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number (REN) is an indication of the maximum number of terminals allowed to be connected to a telephone interface. The terminus of an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all the devices does not exceed five. The modem REN is located on the rear of the equipment on the product labeling.
Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter’s Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.
This equipment uses CA11A telephone jacks.
Ce produit est conforme aux spécifications techniques d’Industrie Canada. Le numéro REN (ringer equivalence number : numéro d’équivalence de sonnerie) fournit une indication du nombre maximum de terminaux pouvant être connectés à l’interface téléphonique. En bout de ligne, le nombre d’appareils qui peuvent être connectés n’est pas directement limité, mais la somme des REN de ces appareils ne doit pas dépasser cinq. Le numéro REN du modem est indiqué sur l’étiquette produit située à l’arrière de l’équipement.
Les compagnies de téléphone constatent que les surtensions électriques, en particulier celles dues à la foudre, entraînent d'importants dégâts sur les terminaux privés connectés à des sources d’alimentation CA. Il s’agit-là d’un problème majeur d’échelle nationale. En conséquence, il vous est recommandé de brancher un parasurtenseur dans la prise de courant à laquelle l’équipement est connecté. Utilisez un parasurtenseur répondant à des caractéristiques nominales satisfaisantes et certifié par le laboratoire d’assureurs UL (Underwriter’s Laboratories), un autre laboratoire agréé de type NRTL (Nationally Recognized Testing Laboratory) ou un organisme de certification agréé dans votre région ou pays. Ceci prévient tout endommagement de l’équipement causé par les orages et autres surtensions électriques.
Cet équipement utilise des prises de téléphone CA11A.
The following are special conditions for the Facsimile User Instructions. The grant of a telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
This equipment shall not be set up to make automatic calls to the Telecom's 111 Emergency Service.
This equipment may not provide for the effective hand-over of a call to another device connected to the same line.
This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom customers.

Some parameters required for compliance with Telecom's telepermit requirements are dependent on the equipment associated with this device. The associated equipment shall be set to operate within the following limits for compliance to Telecom's specifications:
This modem must be used in conjunction with an approved surge protection device when connected to the PSTN.
This product requires a Swiss billing tone filter (Lexmark part number 14B5109 or 80D1877) to be installed on any line which receives metering pulses in Switzerland. The Lexmark filter must be used, as metering pulses are present on all analog telephone lines in Switzerland.
Cet appareil nécessite l’utilisation d’un filtre de tonalité de facturation suisse (nº de référence Lexmark : 14B5109 ou 80D1877) devant être installé sur toute ligne recevant des impulsions de comptage en Suisse. Ce filtre doit être utilisé pour toute installation car ces impulsions existent sur toutes les lignes téléphoniques suisses.
Für dieses Produkt muss ein schweizerischer Billing Tone Filter zur Zählzeichenübertragung (Lexmark Teilenummer 14B5109 oder 80D1877) für jede Leitung installiert werden, über die in der Schweiz Zeitsteuertakte übertragen werden. Die Verwendung des Lexmark Filters ist obligatorisch, da in allen analogen Telefonleitungen in der Schweiz Zeitsteuertakte vorhanden sind.
Questo prodotto richiede un filtro toni Billing svizzero, (codice Lexmark 14B5109 o 80D1877) da installare su tutte le linee che ricevono impulsi remoti in Svizzera. È necessario utilizzare il filtro Lexmark poiché gli impulsi remoti sono presenti su tutte le linee analogiche in Svizzera.

Laser notice
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 5 milliwatt gallium arsenide laser operating in the wavelength of 770-795 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:
The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard-copy output from electronic inputs.
Copying The product is generating hard-copy output from hard-copy original documents.
Scanning The product is scanning hard-copy documents. 165 W
Ready The product is waiting for a print job. 95 W
Power Saver The product is in energy-saving mode. 21W, 24W, 26W
High Off The product is plugged into a wall outlet, but the power switch is turned off.

Mode Description Power consumption (Watts)
Low Off (
turned off, and the product is in the lowest possible power consumption mode.
Off The product is plugged into a wall outlet, but the power switch is turned off.
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Power Saver. The Power Saver Mode is equivalent to the EPA Sleep Mode. The Power Saver Mode saves energy by lowering power consumption during extended periods of inactivity. The Power Saver Mode is automatically engaged after this product is not used for a specified period of time, called the Power Saver Timeout.
Factory default Power Saver Timeout for this product (in minutes): 110V = 45 minutes, 220V = 60 minutes
By using the configuration menus, the Power Saver Timeout can be modified between 1 minute and 240 minutes. Setting the Power Saver Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Power Saver Timeout to a high value maintains a fast response, but uses more energy.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the wall outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.
Lexmark X651de, Lexmark X652de, Lexmark X654de, Lexmark X656de, Lexmark X656dte, Lexmark X658d, Lexmark X658de, Lexmark X658dme, Lexmark X658dfe, Lexmark X658dte, Lexmark X658dtme, Lexmark X658dtfe
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country- specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”

Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).
If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web at http://support.lexmark.com.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment

—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle
—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.
PLEASE READ CAREFULLY BEFORE USING THIS PRODUCT: This License Agreement (“Software License Agreement”) is a legal agreement between you (either an individual or a single entity) and Lexmark International, Inc. (“Lexmark”) that, to the extent your Lexmark product or Software Program is not otherwise subject to a written software license agreement between you and Lexmark or its suppliers, governs your use of any Software Program installed on or provided by Lexmark for use in connection with your Lexmark product. The term “Software Program” includes machine-readable instructions, audio/visual content (such as images and recordings), and associated media, printed materials and electronic documentation, whether incorporated into, distributed with or for use with your Lexmark product.

BY USING THIS PRODUCT, YOU AGREE TO BE BOUND BY ALL THE TERMS AND CONDITIONS OF THIS SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENT. IF YOU DO NOT AGREE WITH THE TERMS OF THIS SOFTWARE LIMITED WARRANTY AND LICENSE AGREEMENT, PROMPTLY RETURN THE PRODUCT UNUSED AND REQUEST A REFUND OF THE AMOUNT YOU PAID. IF YOU ARE INSTALLING THIS PRODUCT FOR USE BY OTHER PARTIES, YOU AGREE TO INFORM THE USERS THAT USE OF THE PRODUCT INDICATES ACCEPTANCE OF THESE TERMS.
1 STATEMENT OF SOFTWARE LIMITED WARRANTY. Lexmark warrants that the media (e.g., diskette or compact disk) on which the Software Program (if any) is furnished is free from defects in materials and workmanship under normal use during the warranty period. The warranty period is ninety (90) days and commences on the date the Software Program is delivered to the original end-user. This limited warranty applies only to Software Program media purchased new from Lexmark or an Authorized Lexmark Reseller or Distributor. Lexmark will replace the Software Program should it be determined that the media does not conform to this limited warranty. 2 DISCLAIMER AND LIMITATION OF WARRANTIES. EXCEPT AS PROVIDED IN THIS SOFTWARE LICENSE AGREEMENT AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, LEXMARK AND ITS SUPPLIERS PROVIDE THE SOFTWARE PROGRAM "AS IS" AND HEREBY DISCLAIM ALL OTHER WARRANTIES AND CONDITIONS, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, TITLE, NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ABSENCE OF VIRUSES, ALL WITH REGARD TO THE SOFTWARE PROGRAM. TO THE EXTENT LEXMARK CANNOT BY LAW DISCLAIM ANY COMPONENT OF THE IMPLIED WARRATIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, LEXMARK LIMITS THE DURATION OF SUCH WARRANTIES TO THE 90-DAY TERM OF THE EXPRESS SOFTWARE LIMITED WARRANTY.
This Agreement is to be read in conjunction with certain statutory provisions, as that may be in force from time to time, that imply warranties or conditions or impose obligations on Lexmark that cannot be excluded or modified. If any such provisions apply, then to the extent Lexmark is able, Lexmark hereby limits its liability for breach of those provisions to one of the following: providing you a replacement copy of the Software Program or reimbursement of the price paid for the Software Program.
The Software Program may include internet links to other software applications and/or internet web pages hosted and operated by third parties unaffiliated with Lexmark. You acknowledge and agree that Lexmark is not responsible in any way for the hosting, performance, operation, maintenance, or content of, such software applications and/or internet web pages. 3 LIMITATION OF REMEDY. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY AND ALL LIABILITY OF LEXMARK UNDER THIS SOFTWARE LICENSE AGREEMENT IS EXPRESSLY LIMITED TO THE GREATER OF THE PRICE PAID FOR THE SOFTWARE PROGRAM AND FIVE U.S. DOLLARS (OR THE EQUIVALENT IN LOCAL CURRENCY). YOUR SOLE REMEDY AGAINST LEXMARK IN ANY DISPUTE UNDER THIS SOFTWARE LICENSE AGREEMENT SHALL BE TO SEEK TO RECOVER ONE OF THESE AMOUNTS, UPON PAYMENT OF WHICH LEXMARK SHALL BE RELEASED AND DISCHARGED OF ALL FURTHER OBLIGATIONS AND LIABILITY TO YOU.
IN NO EVENT WILL LEXMARK, ITS SUPPLIERS, SUBSIDIARIES, OR RESELLERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, EXEMPLARY, PUNITIVE, OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LOST PROFITS OR REVENUES, LOST SAVINGS, INTERRUPTION OF USE OR ANY LOSS OF, INACCURACY IN, OR DAMAGE TO, DATA OR RECORDS, FOR CLAIMS OF THIRD PARTIES, OR DAMAGE TO REAL OR TANGIBLE PROPERTY, FOR LOSS OF PRIVACY ARISING OUT OR IN ANY WAY RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE PROGRAM, OR OTHERWISE IN CONNECTION WITH ANY PROVISION OF THIS SOFTWARE LICENCE AGREEMENT), REGARDLESS OF THE NATURE OF THE CLAIM, INCLUDING BUT NOT LIMITED TO BREACH OF WARRANTY OR CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY), AND EVEN IF LEXMARK, OR ITS SUPPLIERS, AFFILIATES, OR REMARKETERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY YOU BASED ON A THIRD-PARTY CLAIM, EXCEPT TO THE EXTENT THIS EXCLUSION OF DAMAGES IS DETERMINED LEGALLY INVALID. THE FOREGOING LIMITATIONS APPLY EVEN IF THE ABOVE-STATED REMEDIES FAIL OF THEIR ESSENTIAL PURPOSE. 4 U.S.A. STATE LAWS. This Software Limited Warranty gives you specific legal rights. You may also have other rights that vary from state to state. Some states do not allow limitations on how long an implied warranty lasts or the exclusion of limitation of incidental or consequential damages, so the above limitations may not apply to you.

5 LICENSE GRANT. Lexmark grants you the following rights provided you comply with all terms and conditions of this Software License Agreement:
a Use. You may Use one (1) copy of the Software Program. The term “Use” means storing, loading, installing,
executing, or displaying the Software Program. If Lexmark has licensed the Software Program to you for concurrent use, you must limit the number of authorized users to the number specified in your agreement with Lexmark. You may not separate the components of the Software Program for use on more than one computer. You agree that you will not Use the Software Program, in whole or in part, in any manner that has the effect of overriding, modifying, eliminating, obscuring, altering or de-emphasizing the visual appearance of any trademark, trade name, trade dress or intellectual property notice that appears on any computer display screens normally generated by, or as a result of, the Software Program. b Copying. You may make one (1) copy of the Software Program solely for purposes of backup, archiving, or
installation, provided the copy contains all of the original Software Program’s proprietary notices. You may not copy the Software Program to any public or distributed network. c Reservation of Rights. The Software Program, including all fonts, is copyrighted and owned by Lexmark International, Inc. and/or its suppliers. Lexmark reserves all rights not expressly granted to you in this Software License Agreement. d Freeware. Notwithstanding the terms and conditions of this Software License Agreement, all or any portion
of the Software Program that constitutes software provided under public license by third parties (“Freeware”) is licensed to you subject to the terms and conditions of the software license agreement accompanying such Freeware, whether in the form of a discrete agreement, shrink-wrap license, or electronic license terms at the time of download or installation. Use of the Freeware by you shall be governed entirely by the terms and conditions of such license. 6 TRANSFER. You may transfer the Software Program to another end-user. Any transfer must include all software components, media, printed materials, and this Software License Agreement and you may not retain copies of the Software Program or components thereof. The transfer may not be an indirect transfer, such as a consignment. Prior to the transfer, the end-user receiving the transferred Software Program must agree to all these Software License Agreement terms. Upon transfer of the Software Program, your license is automatically terminated. You may not rent, sublicense, or assign the Software Program except to the extent provided in this Software License Agreement. 7 UPGRADES. To Use a Software Program identified as an upgrade, you must first be licensed to the original Software Program identified by Lexmark as eligible for the upgrade. After upgrading, you may no longer use the original Software Program that formed the basis for your upgrade eligibility. 8 LIMITATION ON REVERSE ENGINEERING. You may not alter, decrypt, reverse engineer, reverse assemble, reverse compile or otherwise translate the Software Program or assist or otherwise facilitate others to do so, except as and to the extent expressly permitted to do so by applicable law for the purposes of inter-operability, error correction, and security testing. If you have such statutory rights, you will notify Lexmark in writing of any intended reverse engineering, reverse assembly, or reverse compilation. You may not decrypt the Software Program unless necessary for the legitimate Use of the Software Program. 9 ADDITIONAL SOFTWARE. This Software License Agreement applies to updates or supplements to the original Software Program provided by Lexmark unless Lexmark provides other terms along with the update or supplement. 10 TERM. This Software License Agreement is effective unless terminated or rejected. You may reject or terminate this license at any time by destroying all copies of the Software Program, together with all modifications, documentation, and merged portions in any form, or as otherwise described herein. Lexmark may terminate your license upon notice if you fail to comply with any of the terms of this Software License Agreement. Upon such termination, you agree to destroy all copies of the Software Program together with all modifications, documentation, and merged portions in any form.

11 TAXES. You agree that you are responsible for payment of any taxes including, without limitation, any goods and services and personal property taxes, resulting from this Software License Agreement or your Use of the Software Program. 12 LIMITATION ON ACTIONS. No action, regardless of form, arising out of this Software License Agreement may be brought by either party more than two years after the cause of action has arisen, except as provided under applicable law. 13 APPLICABLE LAW. This Software License Agreement is governed by the laws of the Commonwealth of Kentucky, United States of America. No choice of law rules in any jurisdiction shall apply. The UN Convention on Contracts for the International Sale of Goods shall not apply. 14 UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The Software Program has been developed entirely at private expense. Rights of the United States Government to use the Software Program are as set forth in this Software License Agreement and as restricted in DFARS 252.227-7014 and in similar FAR provisions (or any equivalent agency regulation or contract clause). 15 CONSENT TO USE OF DATA. You agree that Lexmark, its affiliates, and agents may collect and use information you provide in relation to support services performed with respect to the Software Program and requested by you. Lexmark agrees not to use this information in a form that personally identifies you except to the extent necessary to provide such services. 16 EXPORT RESTRICTIONS. You may not (a) acquire, ship, transfer, or reexport, directly or indirectly, the Software Program or any direct product therefrom, in violation of any applicable export laws or (b) permit the Software Program to be used for any purpose prohibited by such export laws, including, without limitation, nuclear, chemical, or biological weapons proliferation. 17 AGREEMENT TO CONTRACT ELECTRONICALLY. You and Lexmark agree to form this Software License Agreement electronically. This means that when you click the “Agree” or “I accept” button on this page or use this product, you acknowledge your agreement to these Software License Agreement terms and conditions and that you are doing so with the intent to “sign” a contract with Lexmark. 18 CAPACITY AND AUTHORITY TO CONTRACT. You represent that you are of the legal age of majority in the place you sign this Software License Agreement and, if applicable, you are duly authorized by your employer or principal to enter into this contract. 19 ENTIRE AGREEMENT. This Software License Agreement (including any addendum or amendment to this Software License Agreement that is included with the Software Program) is the entire agreement between you and Lexmark relating to the Software Program. Except as otherwise provided for herein, these terms and conditions supersede all prior or contemporaneous oral or written communications, proposals, and representations with respect to the Software Program or any other subject matter covered by this Software License Agreement (except to the extent such extraneous terms do not conflict with the terms of this Software License Agreement, any other written agreement signed by you and Lexmark relating to your Use of the Software Program). To the extent any Lexmark policies or programs for support services conflict with the terms of this Software License Agreement, the terms of this Software License Agreement shall control.
1 This product may incorporate intellectual property owned by Microsoft Corporation. The terms and conditions upon which Microsoft is licensing such intellectual property may be found at http://go.microsoft.om/fwlink/?LinkId=52369. 2 This product is based on Microsoft Print Schema technology. You may find the terms and conditions upon which Microsoft is licensing such intellectual property at http://go.microsoft.com/fwlink/?LinkId=83288.







Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.