
User's Guide
Machine type(s):
Model(s):
630, 632, 636


Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible.
Do not place or use this product near water or wet locations.
This product uses a printing process that heats the print media, and the heat may cause the media to release emissions. You must understand the section in your operating instructions that discusses the guidelines for selecting print media to avoid the possibility of harmful emissions.
Use only the power cord provided with this product or the manufacturer's authorized replacement.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer is not responsible for the use of other replacement parts.
CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects such as furniture and walls. If any of these things happen, a risk of fire or electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet before inspecting it.
Refer service or repairs, other than those described in the user documentation, to a service representative.
Safety information 7

SAVE THESE INSTRUCTIONS.
Safety information 8

Learning about the printer 9
Finding information about the printer

Learning about the printer 10
When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options, then also leave enough room for them. It is important to:

Learning about the printer 11


Learning about the printer 12


The scanner provides copy, fax, and scan-to-network capability for workgroups. You can:

Learning about the printer 13

Use the scanner glass for single pages, small items (such as postcards or photos), transparencies, photo paper, or thin media (such as magazine clippings).
You can use the ADF or the scanner glass to scan documents.
The ADF can scan multiple pages including duplex (two‑sided) pages. When using the ADF:
The scanner glass can be used to scan or copy single pages or book pages. When using the scanner glass:

Learning about the printer 14

9 8 10 7
1 Display View scanning, copying, faxing, and printing options as well as status and error messages.
Enter numbers, letters, or symbols on the display.
1@!.
5 JKL 6 MNO 4 GHI
7 PQRS 8 TUV 9 WXYZ
4 Back In the Copy menu, press to delete the right-most digit of the value in the Copy Count. The default value of 1 appears if the entire number is deleted by pressing numerous times.
In the Fax Destination List, press to delete the right-most digit of a number entered manually. You can also press to delete an entire shortcut entry. Once an entire line is deleted, another press of causes the cursor to move up one line.
In the E-mail Destination List, press to delete the character to the left of the cursor. If the character is in a shortcut, then the shortcut is deleted.
5 USB port Insert a flash drive to send data to the printer or to scan a file to the flash drive.
6 Home Press to return to the home screen.
Item Description · 2 Keypad · # 0

Learning about the printer 15
9 Stop Press to stop all printer activity.
A list of options is offered once Stopped appears on the display.
10 Sleep Press to put printer into or out of Sleep Mode.
Item Description

Understanding the home screen 16
Understanding the home screen
When the printer is turned on, the display shows a basic screen, referred to as the home screen. Touch the home screen buttons and icons to initiate an action such as copying, faxing, or scanning; to open the menu screen; or to respond to messages.

Copy Access the Copy menus and make copies.
E-mail Access the E-mail menus and send e‑mails.
Fax Access the Fax menus and send fax.
Access the printer menus.
FTP Access the File Transfer Protocol (FTP) menus and scan documents directly to an FTP server.
USB or USB Thumbdrive View, select, print, scan, or e‑mail photos and documents from a flash drive.
Bookmarks Create, organize, and save a set of bookmarks (URL) into a tree view of folders and file links.
Held Jobs Display all current held jobs.
Touch To

Understanding the home screen 17
Other buttons that may appear on the home screen:
Search held jobs Search on any of the following items:
Release Held Fax Access the list of held faxes.
Lock Device Open a password entry screen. Enter the correct password to lock the printer control panel.
Unlock Device Open a password entry screen. Enter the correct password to unlock the printer control panel.
Cancel Jobs Open the Cancel Jobs screen. The Cancel Jobs screen shows three headings: Print, Fax, and Network.
The following options are available under the Print, Fax, and Network headings:
Each heading has a list of jobs shown in a column under it which can show only three jobs per screen. If more than three jobs exist in a column, then an arrow appears enabling you to scroll through the jobs.
Change Language Launch the Change Language pop‑up window that allows you to change the primary language of the printer.
Touch To

Understanding the home screen 18

Submit Submit changes made in the printer settings.
Sample Copy Print a sample copy.
Scroll to the right.
Scroll to the left.
Return to the home screen.
Select a higher value.
Select a lower value.
Exit from the current screen.

Understanding the home screen 19
Open a context-sensitive Help dialog on the touch screen.
Save a setting.
Reset values on the screen.
Select or clear an item.
Menu trail line:
A menu trail line is located at the top of each menu screen. This feature shows the path taken to arrive at the current menu.
Menus > Settings > Copy Settings > Number of Copies
Touch any of the underlined words to return to that menu.
Number of Copies is not underlined since this is the current screen. If you touch an underlined word on the Number of Copies screen before the Number of Copies is set and saved, then the selection is not saved, and it does not become the default setting.
If an attendance message affects a function, then this icon appears and the red indicator light blinks.

Understanding the home screen 20
Feature Description

Setting up and using the home screen applications 21
Finding the IP address of the printer
You can find the printer IP address:
The Embedded Web Server is the printer Web page that lets you view and remotely configure printer settings even when you are not physically near the printer.
2 Open a Web browser, and then type the printer IP address in the address field.
3 Press Enter.
1 From the Embedded Web Server, click Settings > General Settings > Home screen customization.
A list of basic printer functions appears.
2 Select the check boxes to specify which icons appear on the printer home screen.
Cleared check box items are hidden.
3 Click Submit.

Setting up and using the home screen applications 22
Your printer comes with preinstalled home screen applications. To use these applications, activate and set up these applications using the Embedded Web Server. For more information about accessing the Embedded Web Server, see “Accessing the Embedded Web Server” on page 21.
For detailed information about configuring and using the home screen applications, visit the Lexmark Web site at http://support.lexmark.com.

The application helps you simplify and streamline work processes by letting you quickly find and print frequently used online forms directly from the home screen.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Device Solutions > Solutions (eSF) > Forms and Favorites.
3 Define the bookmarks, and then customize the settings.
4 Click Apply.
To use the application, touch Forms and Favorites on the printer home screen, and then navigate through form categories, or search for forms based on a form number, name, or description.
The application lets you capture a digital image of a hard‑copy document and route it to a shared network folder. You can define up to 30 unique folder destinations.

1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Device Solutions > Solutions (eSF) > Scan to Network.
Icon Description · Icon Description

Setting up and using the home screen applications 23
3 Specify the destinations, and then customize the settings.
4 Click Apply.
To use the application, touch Scan to Network on the printer home screen, and then follow the instructions on the printer display.
The application lets you customize your touch‑screen settings and store those preferences in a flash drive. Each time you want to copy, fax, or scan, insert the flash drive into the USB port of the printer. All your personal preferences are automatically uploaded, including job settings, home screen preferences, and address book.
To set up My MFP, insert a flash drive into the USB port of the printer, and then follow the instructions on the printer display to run the setup wizard.
To use My MFP, insert the flash drive into the USB port of the printer when you want to copy, fax, or scan.
A WS‑Scan icon and its description
The Web Services‑Scan application lets you scan documents at the network printer, and then send the scanned image to your computer. WS‑Scan is a Microsoft application that is similar to Scan to Network, but has the capability of sending the scanned image to a Windows‑based application. To learn more about WS‑Scan, see the Microsoft documentation.
This application shows the printer control panel on your computer screen and lets you interact with the printer control panel, even when you are not physically near the network printer. From your computer screen, you can view the printer status, release held print jobs, create bookmarks, and do other print-related tasks you might normally do while standing at the network printer.
1 Open a Web browser, and then type the printer IP address in the address field.
2 Click Settings > Device Solutions > Solutions (eSF) > Remote Operator Panel.
Icon Description · Icon Description

Setting up and using the home screen applications 24
3 Select the Enabled check box, and then customize the settings.
4 Click Apply.
To use the application, from the Embedded Web Server, click Applications > Remote Operator Panel > Launch VNC Applet.
You can export configuration settings into a text file that can then be imported and used to apply the settings to one or more additional printers.
1 From the Embedded Web Server, click Settings or Configuration.
2 Click Device Solutions > Solutions (eSF), or click Embedded Solutions.
3 From Installed Solutions, click the name of the application you want to configure.
4 Click Configure > Export.
5 Follow the instructions on the computer screen to save the configuration file, and then enter a unique file name or use the default name.
1 From the Embedded Web Server, click Settings or Configuration.
2 Click Device Solutions > Solutions (eSF), or click Embedded Solutions.
3 From Installed Solutions, click the name of the application you want to configure.
4 Click Configure > Import.
5 Browse to the saved configuration file, and then load or preview it.

Additional printer setup 25
Installing internal options
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
You can customize your printer connectivity and memory capacity by adding optional cards. The instructions in this section explain how to install the available cards; you can also use them to locate a card for removal.

Additional printer setup 26
The printer is equipped with a security lock feature. When a lock compatible with most laptop computers is attached, the printer is locked. Once locked, the metal plate and the system board cannot be removed. Attach a security lock to the printer in the location shown.

CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the system board at the back of the printer. a Turn the screws on the cover counterclockwise to remove them. b Remove the cover.

Additional printer setup 27

2 Use the following illustration to locate the connector.

Additional printer setup 28

1 Flash memory or font card connector
2 Memory card connector

Additional printer setup 29
3 Open the memory card connector latches.

4 Unpack the memory card.
5 Align the notches on the memory card with the ridges on the connector.

6 Push the memory card straight into the connector until it snaps into place.
7 Reinstall the system board cover.
1 Notches · 2 Ridges

Additional printer setup 30

CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Access the system board at the back of the printer. a Turn the screws on the cover counterclockwise to remove them. b Remove the cover .

Additional printer setup 31

2 Use the following illustration to locate the connector.

Additional printer setup 32

1 Flash memory or font card connector
2 Memory card connector
3 Unpack the flash memory or font card.

Additional printer setup 33
4 Holding the card by its sides, align the plastic pins on the card with the holes on the system board.

5 Push the card firmly into place.

6 Reinstall the system board cover.
1 Plastic pins · 2 Metal pins

Additional printer setup 34

For more information on installing an optional 550‑sheet tray, see the setup documentation that came with the option.

Additional printer setup 35
The printer supports two additional input sources: an optional 550‑sheet tray and a 650‑sheet duo drawer (Tray 2) with an integrated multipurpose feeder.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well, and unplug any cables going into the printer.
1 Unpack the optional tray, and then remove all packing material and the dust cover.
2 Place the tray near the printer.
3 Align the 650‑sheet duo drawer with the optional 550‑sheet tray, and then lower it into place.


Additional printer setup 36
4 Align the printer with the 650‑sheet duo drawer, lower the printer into place, and then install the dust covers.

Connect the printer to the computer using a USB cable or Ethernet cable.
Be sure to match the following:

Additional printer setup 37


Additional printer setup 38
Once all hardware and software options are installed and the printer is turned on, verify that the printer is set up correctly.
From the home screen, navigate to:
> Reports > Menu Settings Page
If the printer is attached to a network, then print a network setup page to verify the network connection. This page also provides important information that aids network printing configuration.
1 From the home screen, navigate to:
> Reports > Network Setup Page
2 Check the first section of the network setup page, and confirm that the status is Connected.
If the status is Not Connected, then the LAN drop may not be active, or the network cable may be malfunctioning. Consult a system support person for a solution, and then print another network setup page.
2 Double‑click the software installer package.
Wait for the installation dialog to appear.
If you are using a Software and Documentation CD and the installation dialog does not appear, then do the following:
From the Search charm, type run, and then navigate to:
Apps list > Run > type D:\setup.exe > OK.

Additional printer setup 39
or click Start, and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter, or click OK.
Click the CD icon on the desktop.
3 Click Install, and then follow the instructions on the computer screen.
When any hardware options are installed, you may need to manually add the options in the printer driver to make them available for use.
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
4 Click the Configuration tab.
6 Click Apply.
a Click · In Windows 8 · a Click

Additional printer setup 40
2 Add any installed hardware options, and then click OK.
To configure your printer to connect to an Ethernet network, organize the following information before you begin:
You will need an Ethernet cable to connect the printer to the network and an available port where the printer can physically connect to the network. Use a new network cable when possible to avoid potential problems caused by a damaged cable.
2 Double‑click the software installer package.
Wait for the installation dialog to appear.
If you are using the Software and Documentation CD and the installation dialog does not appear, then do the following:
From the Search charm, type run, and then navigate to:
Apps list > Run > type: D:\setup.exe > OK

Additional printer setup 41
or click Start, and then click Run. b In the Start Search or Run dialog, type D:\setup.exe.
c Press Enter, or click OK.
3 Click Install, and then follow the instructions on the computer screen.
4 Select Ethernet connection, and then click Continue.
5 Attach the Ethernet cable when instructed to do so.
6 Select the printer from the list, and then click Continue.
7 Follow the instructions on the computer screen.
1 Allow the network DHCP server to assign an IP address to the printer.
3 Install the printer driver on the computer. a Insert the Software and Documentation CD, and then double‑click the installer package for the printer. b Follow the instructions on the computer screen.
c Select a destination, and then click Continue. d From the Easy Install screen, click Install. e Type the user password, and then click OK.
All the necessary applications are installed on the computer. f Click Close when installation is complete.
4 Add the printer. • For IP printing: a From the Apple menu, navigate to either of the following:
– System Preferences > Print & Scan – System Preferences > Print & Fax b Click +.
c Click the IP tab. d Type the printer IP address in the address field, and then click Add. • For AppleTalk printing:
a Click

Additional printer setup 42
– Make sure AppleTalk is activated on your printer. – This feature is supported only in Mac OS X version 10.5. a From the Apple menu, navigate to:
System Preferences > Print & Fax b Click +, and then navigate to:
AppleTalk > select your printer > Add

Minimizing your printer's environmental impact 43
Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impact on the environment. We design with the environment in mind, engineer our packaging to reduce materials, and provide collection and recycling programs. For more information, see:
By selecting certain printer settings or tasks, you may be able to reduce your printer's impact even further. This chapter outlines the settings and tasks that may yield a greater environmental benefit.
Studies show that as much as 80% of the carbon footprint of a printer is related to paper usage. You can significantly reduce your carbon footprint by using recycled paper and the following printing suggestions, such as printing on both sides of the paper and printing multiple pages on one side of a single sheet of paper.
For information on how you can quickly save paper and energy using one printer setting, see “Using Eco‑Mode” on page 44.
As an environmentally conscious company, Lexmark supports the use of recycled office paper produced specifically for use in laser printers. For more information on recycled papers that work well with your printer, see “Using recycled paper and other office papers” on page 59.
If your printer model supports duplex printing, then you can control whether print appears on one or two sides of the paper by selecting 2‑sided printing from the Print dialog or from the Lexmark Toolbar.
You can print up to 16 consecutive pages of a multiple‑page document onto one side of a single sheet of paper by selecting a setting from the Multipage printing (N‑Up) section of the Print dialog screen.
Before printing or making multiple copies of a document:

Minimizing your printer's environmental impact 44
Correctly set the paper type and size to avoid paper jams. For more information, see “Avoiding jams” on page 230.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > General Settings > Eco‑Mode > select a setting > Submit.
Off Use factory default settings for all settings associated with Eco‑Mode. This setting supports the performance specifications of your printer.
Energy Reduce energy use, especially when the printer is idle.
Energy/Paper Use all the settings associated with Energy mode and Paper mode.
To select a Quiet Mode setting using the Embedded Web Server:
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > General Settings > Quiet Mode > select a setting > Submit.
Choose To

Minimizing your printer's environmental impact 45
Use factory default settings. This setting supports the performance specifications of your printer.
On Reduce printer noise.
To save energy, you can decrease the number of minutes before the printer enters Sleep Mode.
Available settings range from 2–240 minutes. The factory default setting is 30 minutes.
1 Type the printer IP address or host name in the address field of your Web browser.
If you do not know the IP address or host name of the printer, then you can:
2 Click Settings > General Settings > Timeouts.
3 In the Sleep Mode field, enter the number of minutes you want the printer to wait before it enters Sleep Mode.
4 Click Submit.
1 From the home screen, navigate to:
> Settings > General Settings > Timeouts
2 Touch the arrows next to Sleep Mode to select the number of minutes you want the printer to wait before it enters Sleep Mode.
3 Touch Submit.
Choose To · Off

Minimizing your printer's environmental impact 46
To save energy, or if you have trouble reading your display, then adjust the brightness of the display.
Available settings range from 20–100. The factory default setting is 100.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > General Settings.
3 In the Screen Brightness field, enter the brightness percentage you want for the display.
4 Click Submit.
1 From the home screen, navigate to:
> Settings > General Settings
2 Touch the arrows until Screen Brightness appears, and then select a setting.
3 Touch Submit.
Lexmark provides collection programs and environmentally progressive approaches to recycling. For more information, see:
To return Lexmark products for recycling:
1 Go to www.lexmark.com/recycle.
2 Find the product type you want to recycle, and then select your country or region from the list.
3 Follow the instructions on the computer screen.

Minimizing your printer's environmental impact 47
Lexmark continually strives to minimize packaging. Less packaging helps to ensure that Lexmark printers are transported in the most efficient and environmentally sensitive manner and that there is less packaging to dispose of. These efficiencies result in fewer greenhouse emissions, energy savings, and natural resource savings.
Lexmark cartons are 100% recyclable where corrugated recycling facilities exist. Facilities may not exist in your area.
The foam used in Lexmark packaging is recyclable where foam recycling facilities exist. Facilities may not exist in your area.
When you return a cartridge to Lexmark, you can reuse the box that the cartridge came in. Lexmark will recycle the box.
Lexmark Cartridge Collection Program diverts millions of Lexmark cartridges from landfills annually by making it both easy and free for Lexmark customers to return used cartridges to Lexmark for reuse or recycling. One hundred percent of the empty cartridges returned to Lexmark are either reused or demanufactured for recycling. Boxes used to return the cartridges are also recycled.
To return Lexmark cartridges for reuse or recycling, follow the instructions that came with your printer or cartridge and use the prepaid shipping label. You can also do the following:
1 Go to www.lexmark.com/recycle.
2 From the Toner Cartridges section, select your country or region.
3 Follow the instructions on the computer screen.

Loading paper and specialty media 48
This section explains how to use the 250-sheet tray, the manual feeder, an optional 550-sheet tray, and the 650-sheet duo drawer with an integrated multipurpose feeder. It also includes information about paper orientation, setting the Paper Size and Paper Type, and linking and unlinking trays.
The Paper Size setting for the multipurpose feeder must be set manually from the Paper Size menu. The Paper Type setting must be set manually for all trays that do not contain plain paper.
From the home screen navigate to:
> Paper Menu > Paper Size/Type > select a tray > select the paper size or type > Submit
The Universal Paper Size is a user‑defined setting that lets you print on paper sizes that are not preset in the printer menus. Set the Paper Size for the specified tray to Universal when the size you want is not available from the Paper Size menu. Then, specify all of the following Universal size settings for your paper:
1 From the home screen, navigate to:
> Paper Menu > Universal Setup > Units of Measure > select a unit of measure
2 Touch Portrait Width or Portrait Height > select the width or height > Submit.
Loading the standard 250‑sheet tray and optional 550‑sheet tray
The printer has one standard 250-sheet tray (Tray 1) with an attached manual feeder. The 250-sheet tray, the 650- sheet duo drawer, and the optional 550-sheet tray support the same paper sizes and types and are loaded in the same way.
1 Pull the tray out.

Loading paper and specialty media 49

2 Squeeze the length guide tab, and then slide the guide to the correct position for the paper size being loaded.


Loading paper and specialty media 50
3 If the paper is longer than letter‑size paper, then push the green tab at the back of the tray to extend it.

4 Flex the sheets back and forth to loosen them. Do not fold or crease the paper. Straighten the edges on a level surface.

5 Load the paper stack with the recommended print side faceup.

6 Make sure the paper guides are secure against the edges of the paper.

Loading paper and specialty media 51
7 Insert the tray.

8 If a different type or size of paper was loaded than the type or size previously loaded in the tray, then change the Paper Type or Paper Size setting for the tray from the printer control panel.
The 650‑sheet duo drawer (Tray 2) consists of a 550‑sheet tray and an integrated 100‑sheet multipurpose feeder. The drawer is loaded in the same way as the 250‑sheet tray and the optional 550‑sheet tray, and supports the same paper types and sizes. The only differences are the look of the guide tabs and the location of the paper size indicators.

1 Length guide tabs
3 Width guide tabs
2 Size indicators

Loading paper and specialty media 52
1 Push the multipurpose feeder latch to the left.

2 Open the multipurpose feeder.
3 Grasp the extension, and pull it straight out until it is fully extended.
4 Prepare the paper for loading. • Flex sheets of paper back and forth to loosen them. Do not fold or crease the paper. Straighten the edges on a level surface.


Loading paper and specialty media 53
5 Locate the stack height limiter and tab.

2 Stack height limiter
1 Tab · 3 Width guide · 4 Size indicators

Loading paper and specialty media 54
6 Load the paper, and then adjust the width guide to lightly touch the edge of the paper stack. • Load paper, card stock, and transparencies with the recommended print side facedown and the top edge entering first.
7 Make sure the paper is as far into the multipurpose feeder as it will go with very gentle pushing. Paper should lie flat in the multipurpose feeder. Make sure the paper fits loosely in the multipurpose feeder and is not bent or wrinkled.
8 From the printer control panel, set the Paper Size and Paper Type.
The standard 250‑sheet tray has an integrated manual feeder that can be used to print on different types of media one sheet at a time.
1 Send a manual print job.
a With a document open, click File > Print. b Click Properties, Preferences, Options, or Setup.
a With a document open, choose File > Print. b From the Copies & Pages or General pop-up menu, choose Manual Paper.
c Click OK or Print.

Loading paper and specialty media 55
2 When Load Single Sheet Feeder with [paper type] [paper size] appears, load the sheet facedown into the manual feeder. Load envelopes on the left side of the feeder with the flap side up.

3 Adjust the width guides until they lightly touch the sheet. Do not force the width guides against the sheet. Doing so may damage the sheet.

4 Push the sheet in until it stops. The printer pulls it in farther.

Loading paper and specialty media 56
Tray linking is useful for large print jobs or multiple copies. When one linked tray is empty, paper feeds from the next linked tray. When the Paper Size and Paper Type settings are the same for any trays, the trays are automatically linked. The Paper Size setting for all trays must be set manually from the Paper Size menu. The Paper Type setting must be set for all trays from the Paper Type menu. The Paper Type menu and the Paper Size menu are both available from the Paper Size/Type menu.
Change one of the following tray settings:
Paper Type names describe the paper characteristics. If the name that best describes your paper is used by linked trays, then assign a different Paper Type name to the tray, such as Custom Type [x], or define your own custom name. • Paper Size
Paper Size settings must be set manually from the Paper Size menu.
If the printer is on a network, you can use the Embedded Web Server to define a name other than Custom Type [x] for each of the custom paper types loaded into the printer.
1 Type the printer IP address into the address field of your Web browser.
2 Click Settings > Paper Menu > Custom Name > type a name > Submit.
3 Click Custom Types > select a paper type > Submit.
Assign a custom paper type name to a tray when linking or unlinking trays.
From the home screen, navigate to:
> Paper Menu > Paper Size/Type > select a custom paper type name > select a tray > Submit

Loading paper and specialty media 57
If the printer is on a network, then you can use the Embedded Web Server to define a name other than Custom Type [x] for each of the custom paper types loaded into the printer.
1 Type the printer IP address in the address field of your Web browser.
2 Click Settings > Paper Menu > Custom Types > select the custom name you want to configure > select a paper or specialty media type > Submit.

Paper and specialty media guide 58
The following paper characteristics affect print quality and reliability. Consider these characteristics when evaluating new paper stock.
The printer can automatically feed paper weights from 60 to 176 g/m2 (16 to 47 lb bond) grain long. Paper lighter than 75 g/m2 (20 lb) might not be stiff enough to feed properly, causing jams. For best performance, use 80 g/m2 (21 lb bond) grain long paper. For paper smaller than 182 x 257 mm (7.2 x 10.1 in.), we recommend 90 g/m2 or heavier paper.
Curl is the tendency for paper to curl at its edges. Excessive curl can cause paper feeding problems. Curl can occur after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in hot, humid, cold, or dry conditions, even in the trays, can contribute to paper curling prior to printing and can cause feeding problems.
Paper smoothness directly affects print quality. If paper is too rough, toner cannot fuse to it properly. If paper is too smooth, it can cause paper feeding or print quality issues. Always use paper between 100 and 300 Sheffield points; however, smoothness between 150 and 200 Sheffield points produces the best print quality.
The amount of moisture in paper affects both print quality and the ability of the printer to feed the paper correctly. Leave paper in its original wrapper until it is time to use it. This limits the exposure of paper to moisture changes that can degrade its performance.
Condition paper before printing by storing it in its original wrapper in the same environment as the printer for 24 to 48 hours before printing. Extend the time several days if the storage or transportation environment is very different from the printer environment. Thick paper may also require a longer conditioning period.

Paper and specialty media guide 59
Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.
For 60 to 176 g/m2 (16 to 47 lb bond) paper, use grain long fibers.
Most high‑quality xerographic paper is made from 100% chemically treated pulped wood. This content provides the paper with a high degree of stability resulting in fewer paper feeding problems and better print quality. Paper containing fibers such as cotton possesses characteristics that can negatively affect paper handling.
Using the appropriate paper prevents jams and helps ensure trouble‑free printing.
To help avoid paper jams and poor print quality:
As an environmentally conscientious company, Lexmark supports the use of recycled paper produced specifically for use in laser (electrophotographic) printers.
While no blanket statement can be made that all recycled paper will feed well, Lexmark consistently tests papers that represent recycled cut size copier papers available on the global market. This scientific testing is conducted with rigor and discipline. Many factors are taken into consideration both separately and as a whole, including the following:
Recycled papers are better than ever; however, the amount of recycled content in a paper affects the degree of control over foreign matter. And while recycled papers are one good path to printing in an environmentally responsible manner, they are not perfect. The energy required to de-ink and deal with additives such as colorants and “glue” often generates more carbon emissions than does normal paper production. However, using recycled papers enables better resource management overall.

Paper and specialty media guide 60
Lexmark concerns itself with the responsible use of paper in general based on life cycle assessments of its products. To gain a better understanding of the impact of printers on the environment, the company commissioned a number of life cycle assessments and found that paper was identified as the primary contributor (up to 80%) of carbon emissions caused throughout the entire life of a device (from design to end-of-life). This is due to the energy-intensive manufacturing processes required to make paper.
Thus, Lexmark seeks to educate customers and partners on minimizing the impact of paper. Using recycled paper is one way. Eliminating excessive and unnecessary paper consumption is another. Lexmark is well-equipped to help customers minimize printing and copying waste. In addition, the company encourages purchasing paper from suppliers who demonstrate their commitment to sustainable forestry practices.
Lexmark does not endorse specific suppliers, although a converter’s product list for special applications is maintained. However, the following paper choice guidelines will help alleviate the environmental impact of printing:
1 Minimize paper consumption.
2 Be selective about the origin of wood fiber. Buy from suppliers who carry certifications such as the Forestry Stewardship Council (FSC) or The Program for the Endorsement of Forest Certification (PEFC). These certifications guarantee that the paper manufacturer uses wood pulp from forestry operators that employ environmentally and socially responsible forest management and restoration practices.
3 Choose the most appropriate paper for printing needs: normal 75 or 80 g/m2 certified paper, lower weight paper, or recycled paper.
Test results indicate that the following paper types are at risk for use with laser printers:
For more information about Lexmark, visit www.lexmark.com. General sustainability-related information can be found at the Environmental Sustainability link.

Paper and specialty media guide 61
Use these paper storage guidelines to help avoid jams and uneven print quality:
The following tables provide information on standard and optional paper sources and the types of paper they support.
Paper size Dimensions 250‑sheet tray Optional 550‑sheet tray Multipurpose feeder
A4 210 x 297 mm (8.3 x 11.7 in.)
A5 148 x 210 mm (5.83 x 8.3 in.)
JIS B5 182 x 257 mm (7.2 x 10.1 in.)
A6 105 x 148 mm (4.1 x 5.8 in.)
* When Universal is selected, the page is formatted for 216 x 356 mm (8.5 x 14 in.) unless the size is specified by the software program.
Manual feeder

Paper and specialty media guide 62

Paper size Dimensions 250‑sheet tray Optional 550‑sheet tray Multipurpose feeder
Statement 140 x 216 mm (5.5 x 8.5 in.)
Letter 216 x 279 mm (8.5 x 11 in.)
Folio 216 x 330 mm (8.5 x 13 in.)
Oficio (Mexico) 216 x 340 mm (8.5 x 13 in.)
Legal 216 x 356 mm (8.5 x 14 in.)
Executive 184 x 267 mm (7.3 x 10.5 in.)
Universal* 148 x 210 mm (5.8 x 8.3 in.) up to 216 x 356 mm (8.5 x 14 in.)
76 x 127 mm (3 x 5 in.) up to 216 x 356 mm (8.5 x 14 in.)
9 Envelope 98 x 225 mm (3.9 x 8.9 in.)
10 Envelope 105 x 241 mm (4.1 x 9.5 in.)
DL Envelope 110 x 220 mm (4.3 x 8.7 in.)
B5 Envelope 176 x 250 mm (6.9 x 9.8 in.)
C5 Envelope 162 x 229 mm (6.4 x 9 in.)
Monarch 105 x 241 mm (4.1 x 9.5 in.)
Other Envelope 98 x 162 mm (3.9 x 6.3 in.) up to 176 x 250 mm (6.9 x 9.8 in.)
* When Universal is selected, the page is formatted for 216 x 356 mm (8.5 x 14 in.) unless the size is specified by the software program.

Paper and specialty media guide 63
Paper type Standard 250‑sheet tray
Optional 550‑sheet tray
Multipurpose feeder Manual feeder
Card stock1, 2, 3
Labels2, 4, 5
Envelopes2, 6, 7 X X
1 Paper types must be set to match the supported paper weights.
2 The duplex unit supports paper weights from 60 to 105 g/m2 (16–28‑lb) grain long bond paper. The duplex unit does not support card stock, transparencies, envelopes, or labels.
3 For 60 to 176 g/m2 (16–47‑lb) bond paper, we recommend grain long fibers.
4 The pressure‑sensitive area must enter the printer first.
5 Single-sided paper labels designed for laser printers are supported for occasional use. The use of paper labels should not exceed 20 pages per month. Prolonged use may reduce fuser life. Vinyl, pharmacy, and dual-sided labels are not supported. For more information, see the Card Stock & Label Guide on the Lexmark Web site at http://support.lexmark.com.
6 The maximum weight for 100 percent cotton envelopes is 90 g/m2 (24‑lb) bond.
7 The cotton content limit for 105 g/m2 (28‑lb) bond envelopes is 25 percent.
Paper · Recycled · Transparencies X

This chapter covers printing, printer reports, and job cancelation. The selection and handling of paper and specialty media can affect how reliably documents print. For more information, see “Avoiding jams” on page 230 and “Storing paper” on page 61.
1 From the printer control panel Paper menu, set the Paper Type and Paper Size to match the loaded paper.
2 Send the print job:
a With a document open, click File > Print. b Click Properties, Preferences, Options, or Setup.
c Adjust settings as necessary. d Click OK > Print.
a Customize the settings as needed in the Page Setup dialog:
1 With a document open, choose File > Page Setup. 2 Choose a paper size or create a custom size to match the loaded paper. 3 Click OK. b Customize the settings as needed in the Print dialog:
1 With a document open, choose File > Print. If necessary, click the disclosure triangle to see more options. 2 From the Print dialog and pop‑up menus, adjust the settings as needed.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > Print Settings > Quality Menu > Toner Darkness.
Printing 64

3 Adjust the toner darkness setting.
4 Click Submit.
For the list of supported mobile devices and to download a compatible mobile printing application, visit http://lexmark.com/mobile.
1 Insert a flash drive into the USB port.



Printing 65




2 From the printer control panel, touch the document you want to print.
3 Touch the arrows to increase the number of copies to print, and then touch Print.
Flash drive File type
Documents:
Printing 66

Card stock is heavy, single‑ply specialty media. Many of its variable characteristics, such as moisture content, thickness, and texture, can significantly impact print quality. Print samples on the card stock being considered for use before buying large quantities.
When printing on card stock:
Print samples on the envelopes being considered for use before buying large quantities.
When printing on envelopes:
Printing 67

– Have bent corners – Have rough, cockle, or laid finishes • Adjust the width guides to fit the width of the envelopes.
Page orientation is important when printing on letterhead. Use the following table to determine which direction to load the letterhead:

Printed letterhead design is placed faceup. The top edge of the sheet with the logo is placed at the front of the tray.
Printed letterhead design is placed facedown. The top edge of the sheet with the logo is placed at the back of the tray.
Printing 68


Preprinted letterhead design is placed facedown. The top edge of the sheet with the logo should enter the manual feeder first.
Preprinted letterhead design is placed faceup. The top edge of the sheet with the logo should enter the manual feeder last.
For detailed information on label printing, characteristics, and design, see the Card Stock & Label Guide available on the Lexmark Web site at http://support.lexmark.com.
When printing on labels:
releasing hazardous emissions.
delaminating, oozing around the edges, or releasing hazardous fumes. • Do not use labels with slick backing material.
Printing 69

Print a test page on the transparencies being considered for use before buying large quantities.
When printing on transparencies:
You can set the printer to store print jobs in the printer memory until you start the print job from the printer control panel.
All print jobs that can be initiated by the user at the printer are called held jobs.
Print job type Description
Confidential Confidential lets you hold print jobs in the computer until you enter the PIN from the control panel.
Verify Verify lets you print one copy of a print job while the printer holds the remaining copies. It allows you to examine if the first copy is satisfactory. The print job is automatically deleted from the printer memory once all copies are printed.
Reserve Reserve allows the printer to store print jobs for printing at a later time. The print jobs are held until deleted from the Help Jobs menu.
Repeat Repeat prints and stores print jobs in the printer memory for reprinting.
Printing 70

1 With a document open, click File > Print.
2 Click Properties, Preferences, Options, or Setup.
3 Click Print and Hold.
4 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
5 Click OK or Print.
1 With a document open, choose File > Print.
If necessary, click the disclosure triangle to see more options.
2 From the print options or Copies & Pages pop‑up menu, choose Job Routing.
3 Select the print job type (Confidential, Repeat, Reserve, or Verify), and then assign a user name. For a confidential print job, also enter a four‑digit PIN.
4 Click OK or Print.
Printing 71

You can connect a PictBridge‑enabled digital camera to the printer, and use the buttons on the camera to select and print photos.
1 Insert one end of the USB cable into the camera.
2 Insert the other end of the USB cable into the USB port on the front of the printer.

3 Follow the instructions on the camera to select and print photos.
1 From the home screen, navigate to:
> Reports > Print Fonts
2 Touch PCL Fonts or PostScript Fonts.
A directory list shows the resources stored in a flash memory or on the printer hard disk.
From the home screen, navigate to:
> Reports > Print Directory
Printing 72

1 From the printer control panel, touch Cancel Job or press on the keypad.
2 Touch the print job you want to cancel, and then touch Delete Selected Jobs.
1 Open the printers folder.
From the Search charm, type run, and then navigate to:
Apps list > Run > type control printers > OK
In Windows 7 or earlier
or click Start, and then click Run. b In the Start Search or Run dialog, type control printers.
c Press Enter, or click OK.
2 Double‑click the printer icon.
3 Select the print job you want to cancel.
4 Click Delete.
2 From the printer window, select the print job you want to cancel, and then delete it.
Printing 73 · In Windows 8 · a Click


Use the ADF for multiple‑page documents. Use the scanner glass for single pages, small items (such as postcards or
photos), transparencies, photo paper, or thin media (such as magazine clippings).
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the printer control panel, touch Copy It.
1 Load an original document faceup, short edge first into the ADF.
2 Adjust the paper guides.
3 From the home screen, navigate to:
Copy > change the copy settings > Copy It
Copying 74

1 Place an original document facedown on the scanner glass in the upper left corner.
2 From the home screen, navigate to:
Copy > change the copy settings > Copy It
3 If you have more pages to scan, then place the next document on the scanner glass, and then touch Scan the Next Page.
4 Touch Finish the Job to return to the home screen.
1 Place a photo facedown on the upper left corner of the scanner glass.
2 From the home screen, navigate to:
Copy > Content > Photo >
> Copy It > Scan the Next Page or Finish the Job
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > size of the original document >
4 Touch Copy to, and then select the tray that contains transparencies, or touch Manual Feeder Size.
5 Load transparencies in the multipurpose feeder.
6 From the home screen, navigate to:
> select the desired size of the transparencies > Manual Feeder Type >
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > size of the original document > Copy to > Manual Feeder
Copying 75 · > Photo/Film > · > Copy It

4 Place the letterhead faceup, top edge first in the multipurpose feeder.
5 Select the size of the letterhead.
6 Navigate to:
Continue > Letterhead > Continue > Copy It
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Allow color copies > Off >
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 Touch Copy from > select the size of the original document >
5 Touch Copy to > select the size of the copy >
6 Touch Copy It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > size of the original document > Copy to
Copying 76 · > Submit

4 Touch Manual Feeder or select the tray that contains the paper type you want to use.
5 Touch Copy It.
Use the ADF to copy original documents with different paper sizes. Depending on the paper sizes loaded and the “Copy to” and “Copy from” settings, each copy is either printed on mixed paper sizes (Example 1) or scaled to fit a single paper size (Example 2).
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > Mixed Sizes >
> Copy to > Auto Size Match >
The scanner identifies the different paper sizes as they are scanned. Copies are printed on mixed paper sizes corresponding to the paper sizes of the original document.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Copy from > Mixed Sizes >
> Copy to > Letter >
The scanner identifies the different paper sizes as they are scanned, and then scales the mixed paper sizes to fit on the paper size selected.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
Copying 77 · > Copy It · > Copy It

4 From the Sides (Duplex) area, touch the button for your preferred duplexing method.
The first number represents sides of the original documents; the second number represents sides of the copy. For example, select 1‑sided to 2‑sided if you have 1-sided original documents and you want 2‑sided copies.
, and then Copy It.
Copies can be reduced to 25% of the original document size or enlarged to 400% of the original document size. The factory default setting for Scale is Auto. If you leave Scale set to Auto, the content of your original document will be scaled to fit the size of the paper onto which you are copying.
To reduce or enlarge a copy:
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 On the home screen, touch Copy.
4 From the Scale area, touch the arrows to enlarge or reduce your copies.
Touching “Copy to” or “Copy from” after setting Scale manually changes the scale value back to Auto.
5 Touch Copy It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:

> Copy It.
If you print multiple copies of a document, then you can choose to print each copy as a set (collated) or to print the copies as groups of pages (not collated).
By default, Collate is set to On. If you do not want to collate your copies, then change the setting to Off:
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > enter the number of copies > Collate > Off >
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Advanced Options > Separator Sheets

> Copy It.
In order to save paper, you can copy either two or four consecutive pages of a multiple‑page document onto a single sheet of paper.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Advanced Options > Paper Saver > select desired output >
The custom copy job or job build is used to combine one or more sets of original documents into a single copy job. Each set may be scanned using different job parameters. When a copy job is submitted and Custom Job is enabled, the scanner scans the first set of original documents using the supplied parameters, and then it scans the next set with the same or different parameters.
The definition of a set depends on the scan source:
For example:
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Options > Custom Job > On > Done > Copy It
When the end of a set is reached, the scan screen appears.
Copying 80 · 5 Touch · > Copy It

4 Load the next document faceup, short edge first into the ADF or facedown on the scanner glass, and then touch Scan the Automatic Document Feeder or Scan the flatbed.
5 If you have another document to scan, then repeat the previous step. Otherwise, touch Finish the job.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Advanced Options > Header/Footer
4 Pick an area of the page where you want to place the date and time.
5 Touch Yes or No >
> Copy It.
An overlay message can be placed on each page. The message choices are Urgent, Confidential, Copy, Custom or Draft. To place a message on the copies:
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Copy > Advanced Options > Overlay > select overlay message >
4 Touch Copy It.
When the ADF begins processing a document, the scanning screen appears. To cancel the copy job, touch Cancel Job on the touch screen.
A “Canceling scan job” screen appears. The ADF clears all pages in the ADF and cancels the job.
Copying 81

Touch Cancel Job on the touch screen.
A “Canceling scan job” screen appears. Once the job is canceled, the copy screen appears.
1 From the printer control panel, touch Cancel Job or press on the keypad.
2 Touch the job you want to cancel, and then touch Delete Selected Jobs.
This option opens a screen where you can enter the paper size of the original document.
This option opens a screen where you can enter the paper size and type on which your copies will be printed.
This option allows you to set the number of copies to be printed.
This option creates an image from your copy that is proportionally scaled anywhere between 25% and 400%. Scale can also be set for you automatically.
Copying 82

This option adjusts how light or dark your copies will turn out in relation to the original document.
Use this option to select duplex settings. You can print copies on one or two sides, make two-sided copies (duplex) of two-sided original documents, make two-sided copies from one-sided original documents, or make one-sided copies (simplex) from two-sided original documents.
This option keeps the pages of a print job stacked in sequence when printing multiple copies of the document. The factory default setting for Collate is on; the output pages of your copies will be ordered (1,2,3) (1,2,3) (1,2,3). If you want all the copies of each page to remain together, turn Collate off, and your copies will be ordered (1,1,1) (2,2,2) (3,3,3).
This option lets you set the original document type and source.
Choose content type from Text, Text/Photo, Photo, or Graphics.
Choose content source from Color Laser, Black/White Laser, Inkjet, Photo/Film, Magazine, Newspaper, Press, or Other.
This option enables or disables color for the scanned image.
Copying 83

Touching the Advanced Options button opens a screen where you can change the following settings:
This option allows the current settings to be saved as a shortcut by assigning a number.
Copying 84


Use the ADF for multiple‑page documents. Use the scanner glass for single pages, small items (such as postcards or
photos), transparencies, photo paper, or thin media (such as magazine clippings).
You can use the printer to e‑mail scanned documents to one or more recipients. There are three ways to send an e‑mail from the printer. You can type the e‑mail address, use a shortcut number, or use the address book.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings.
3 Under Default Settings, click E-mail/FTP Settings.
4 Click E-mail Settings > Setup E-mail Server.
5 Fill in the fields with the appropriate information.
6 Click Submit.
E-mailing 85

1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > E-mail/FTP Settings > E-mail Settings.
3 Fill in the fields with the appropriate information.
4 Click Submit.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings.
3 Under Other Settings, click Manage Shortcuts > E-mail Shortcut Setup.
4 Type a unique name for the recipient, and then enter the e-mail address.
5 Select the scan settings (Format, Content, Color, and Resolution).
6 Enter a shortcut number, and then click Add.
If you enter a number that is already in use, then you are prompted to select another number.
1 From the home screen, navigate to:
E-mail > Recipient > type an e‑mail address
To create a group of recipients, touch Next address, and then type the next recipient’s e-mail address.
3 Type a unique name for the shortcut, and then touch Done.
4 Verify that the shortcut name and number are correct, and then touch OK.
If the name or number is incorrect, then touch Cancel, and then reenter the information.
E-mailing 86 · 2 Touch

1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
4 Enter the e‑mail address, or press # and then enter the shortcut number.
To enter additional recipients, touch Next Address, and then enter the address or shortcut number you want to add.
5 Touch Done > Send It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 Press # , enter the shortcut number using the keypad, and then touch
To enter additional recipients, touch Next address, and then enter the address or shortcut number you want to add.
4 Touch Send It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
E-mail >Recipient(s) >
> enter the name of recipient > Browse shortcuts
E-mailing 87 · E-mail > Recipient

4 Touch the name of the recipients.
To enter additional recipients, touch Next address, and then enter the address or shortcut number you want to add, or search the address book.
5 Touch Done.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, touch E-mail.
4 Type an e‑mail address.
5 Touch Options > Subject.
6 Type the e-mail subject.
7 Touch Done > Message.
8 Type an e-mail message.
9 Touch Done > E-mail It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
E-mail > Recipient > type an e‑mail address > Send as
E-mailing 88

5 Touch E‑mail It.
This option lets you enter the destination of your e-mail. You may enter multiple e‑mail addresses.
This option lets you enter a subject line for your e-mail.
This option lets you enter a message that will be sent with your scanned attachment.
This option lets you customize the attachment file name.
This option opens a screen where you can choose the size of the documents you are going to e-mail.
Adjusts the output quality of your e-mail. Increasing the image resolution increases the e-mail file size and the time needed to scan your original document. Image resolution can be decreased to reduce the e-mail file size.
E-mailing 89

This option sets the output color for the scanned image. Touch to enable or disable color.
This option lets you specify the content type and source of the original document.
Choose content type from Text, Text/Photo, Photo, or Graphics.
Choose content source from Color Laser, Black/White Laser, Inkjet, Photo/Film, Magazine, Newspaper, Press, or Other.
This option adjusts how light or dark your scanned documents will turn out in relation to the original document.
This option sets the output (PDF, TIFF, JPEG or XPS) for the scanned image.
E-mailing 90

This option lets you change the Sides (Duplex), Orientation, and Binding.
This option displays the first page of the image before it is included in the e-mail. When the first page is scanned, the scanning is paused and a preview image appears.
Touching this button opens a screen where you can change the following settings:
E-mailing 91


Use the ADF for multiple‑page documents. Use the scanner glass for single pages, small items (such as postcards or
photos), transparencies, photo paper, or thin media (such as magazine clippings).
The following connection methods may not be applicable in all countries or regions.

Faxing 92

To enter your fax setup information, use the printer control panel, or use your browser to access the Embedded Web Server and then enter the Settings menu.
When the printer is turned on for the first time or if the printer has been off for an extended time, a series of start‑up screens appear. If the printer has fax capabilities, then the following screens appear:
Fax Name or Station Name Fax Number or Station Number
1 When Fax Name or Station Name appears, enter the name to be printed on all outgoing faxes.
2 After entering the Fax Name or Station Name, touch Submit.
3 When Fax Number or Station Number appears, enter the printer fax number.
4 After entering the Fax Number or Station Number, touch Submit.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > Fax Settings > Analog Fax Setup.
3 In the Fax Name or Station Name field, enter the name to be printed on all outgoing faxes.
4 In the Fax Number or Station Number field, enter the printer fax number.
5 Click Submit.
You can connect the printer with equipment such as a telephone, an answering machine, or a computer modem. To determine the best way to set up the printer, see the following table.
Faxing 93

Equipment and service options Fax connection setup
Connect directly to the telephone line See “Connecting to an analog telephone line” on page 94
Connect to a Digital Subscriber Line (DSL or ADSL) service
See “Connecting to a DSL service” on page 94.
Connect to a Private Branch eXchange (PBX) or Integrated Services Digital Network (ISDN) system
See “Connecting to a PBX or ISDN system” on page 95.
Use a Distinctive Ring service See “Connecting to a distinctive ring service” on page 95.
Connect to a telephone line, telephone, and answering machine
See “Connecting the printer and a telephone or answering machine to the same telephone line” on page 96
Connect through an adapter used in your area See “Connecting to an adapter for your country or region” on page 98.
Connect to a computer with a modem See “Connecting to a computer with a modem” on page 102.
If your telecommunications equipment uses a US‑style (RJ11) telephone line, then follow these steps to connect the equipment:
1 Connect one end of the telephone cable that came with the printer to the printer LINE port .
2 Connect the other end of the telephone cable to an active analog telephone wall jack.

If you subscribe to a DSL service, then contact the DSL provider to obtain a DSL filter and telephone cord, and then follow these steps to connect the equipment:
1 Connect one end of the telephone cable that came with the printer to the printer LINE port .
2 Connect the other end of the telephone cable to the DSL filter.
Faxing 94

3 Connect the DSL filter cable to an active telephone wall jack.

If you use a PBX or ISDN converter or terminal adapter, then follow these steps to connect the equipment:
1 Connect one end of the telephone cable that came with the printer to the printer LINE port .
2 Connect the other end of the telephone cable to the port designated for fax and telephone use.
A distinctive ring service may be available from your telephone service provider. This service allows you to have multiple telephone numbers on one telephone line, with each telephone number having a different ring pattern. This may be useful for distinguishing between fax and voice calls. If you subscribe to a distinctive ring service, then follow these steps to connect the equipment:
1 Connect one end of the telephone cable that came with the printer to the printer LINE port .
2 Connect the other end of the telephone cable to an active analog telephone wall jack.

3 Change the Distinctive Rings setting to match the setting you want for the printer to answer:
Faxing 95

a From the home screen, navigate to:
> Settings > Fax Settings > Analog Fax Settings > Distinctive Rings b Select the pattern setting you want to change, and then touch Submit.
Connecting the printer and a telephone or answering machine to the same telephone line
1 Connect one end of the telephone cable that came with the printer to the printer LINE port .
2 Connect the other end of the telephone cable to an active analog telephone wall jack .

3 Remove the plug from the printer EXT port .
4 Connect your telecommunications equipment directly to the printer EXT port .
Use one of the following methods:
Faxing 96


Telephone or a telephone with an integrated answering machine
Faxing 97

The following countries or regions may require a special adapter to connect the telephone cable to the active telephone wall jack:
For some countries or regions, a telephone line adapter is included in the box. Use this adapter to connect an answering machine, telephone, or other telecommunications equipment to the printer.
1 Connect one end of the telephone cable that came with the printer to the printer LINE port .
2 Connect the other end of the telephone cable to the adapter, and then connect the adapter to the active telephone wall jack.

3 Connect the answering machine or telephone to the adapter.
Faxing 98 · Country/region

Use one of the following methods:

Faxing 99

There is a special RJ‑11 plug installed in the printer EXT port . Do not remove this plug. It is necessary for the proper operation of the fax function and connected telephones.

Connecting to a telephone wall jack in Germany
1 Connect one end of the telephone cable that came with the printer to the printer LINE port .
2 Connect the other end of the telephone cable to the adapter.
Faxing 100


3 Connect the adapter into the N slot of an active analog telephone wall jack.

Faxing 101

4 If you would like to use the same line for both fax and telephone communication, then connect a second telephone line (not provided) between the telephone and the F slot of an active analog telephone wall jack.

5 If you would like to use the same line for recording messages on your answering machine, then connect a second telephone cable (not provided) between the answering machine and the other N slot of the active analog telephone wall jack.

Connect the printer to a computer with a modem to send faxes from the software program.
1 Connect one end of the telephone cable that came with the printer to the printer LINE port .
2 Connect the other end of the telephone cable to an active analog telephone wall jack.

Faxing 102

3 Remove the protective plug from the printer EXT port .

4 Connect your telephone to the computer telephone jack.

Faxing 103

5 Connect an additional telephone cord (not provided) from the computer modem to the printer EXT port .

1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > Fax Settings > Analog Fax Setup.
3 In the Fax Name or Station Name field, enter the name to be printed on all outgoing faxes.
4 In the Fax Number or Station Number field, enter the printer fax number.
5 Click Submit.
You can set the date and time so that they are printed on every fax you send. If there is a power failure, then you may have to reset the date and time.
1 Type the printer IP address in the address field of your Web browser.
Faxing 104

If you do not know the IP address of the printer, then you can:
2 Click Security > Set Date and Time.
3 In the Set Date & Time field, enter the current date and time.
4 Click Submit.
The printer can be set to automatically adjust for daylight saving time:
1 Type the printer IP address in the address field of your Web browser.
If you do not know the IP address of the printer, then you can:
2 Click Security > Set Date and Time.
3 Select the Automatically Observe DST checkbox, and then enter the DST start and end dates in the Custom Time Zone Setup section.
4 Click Submit.
Instead of entering the entire phone number of a fax recipient on the printer control panel each time you want to send a fax, you can create a permanent fax destination and assign a shortcut number. A shortcut can be created to a single fax number or a group of fax numbers.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > Manage Shortcuts > Fax Shortcut Setup.
3 Type a unique name for the shortcut, and then enter the fax number.
To create a multiple‑number shortcut, enter the fax numbers for the group.
Faxing 105

4 Assign a shortcut number.
If you enter a number that is already in use, then you are prompted to select another number.
5 Click Add.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Fax > enter the fax number
To create a group of fax numbers, touch Next number, and then enter the next fax number.
4 Navigate to:
> enter a name for the shortcut > Done > OK > Fax It
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, touch Fax.
4 Enter the fax number or a shortcut using the touch screen or keypad.
To add recipients, touch Next Number and then enter the recipient's telephone number or shortcut number, or search the address book.
5 Touch Fax It.
The printer driver fax option lets you send a print job to the printer, which sends the job as a fax. The fax option works as a normal fax machine, but is controlled through the printer driver instead of the printer control panel.
1 With a document open, click File > Print.
2 Select the printer, and then click Properties, Preferences, Options, or Setup.
Faxing 106

3 Navigate to:
Fax tab > Enable fax
4 Enter the recipient fax number or numbers in the “Fax number(s)” field.
5 If necessary, enter a prefix in the “Dialing prefix” field.
6 Select the appropriate paper size and page orientation.
7 If you want to include a cover page with the fax, then select Include cover page with fax, and then enter the appropriate information.
8 Click OK.
Fax shortcuts are just like the speed dial numbers on a telephone or fax machine. A shortcut number (1–99999) can contain a single recipient or multiple recipients.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 Press # , and then enter the shortcut number using the keypad.
4 Touch Fax It.
The address book enables you to search for bookmarks and network directory servers.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Faxing 107 · Fax > · > Browse shortcuts

4 Using the virtual keyboard, type the name or part of the name of the person whose fax number you want to find.
5 Touch Done > Fax It.
Settings range from Standard (fastest speed) to Super Fine (slowest speed but best quality).
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Fax > enter the fax number > Options
4 From the Resolution area, touch the arrows to change to the resolution you want.
5 Touch Fax It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
Fax > enter the fax number > Options
4 From the Darkness area, touch the arrows to adjust the darkness of the fax.
5 Touch Fax It.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
Faxing 108

3 From the home screen, navigate to:
Fax > enter the fax number > Options > Advanced Options > Delayed Send
4 Touch the arrows to adjust the time the fax will be transmitted.
The time is increased or decreased in increments of 30 minutes. If the current time is shown, the left arrow is unavailable.
5 Touch Fax It.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > Reports > Fax Job Log or Fax Call Log.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > Fax Settings > Analog Fax Setup > Block No Name Fax.
Faxing 109

1 On the home screen, touch Cancel Jobs.
The Cancel Jobs screen appears.
2 Touch the job or jobs you want to cancel.
Only three jobs appear on the screen; touch the down arrow until the job you want appears, and then touch the job you want to cancel.
3 Touch Delete Selected Jobs.
The Deleting Selected Jobs screen appears, the selected jobs are deleted, and then the home screen appears.
This option lets you specify the content type and source of the original document.
Choose content type from Text, Text/Photo, Photo, or Graphics.
Choose content source from Color Laser, Black/White Laser, Inkjet, Photo/Film, Magazine, Newspaper, Press, or Other.
This options increases how closely the scanner examines the document you want to fax. If you are faxing a photo, a drawing with fine lines, or a document with very small text, then increase the Resolution setting. This will increase the amount of time required for the scan and will increase the quality of the fax output.
Faxing 110

This option adjusts how light or dark your faxes will turn out in relation to the original document.
This option enables or disables color in faxing.
This option lets you change the Sides (Duplex), Orientation, and Binding.
This option displays the first page of the image before it is included in the fax. When the first page is scanned, the scanning is paused and a preview image appears.
This lets you send a fax at a later time or date.
1 Set up your fax.
2 From the home screen, navigate to:
Delayed Send > enter the date and time you want to send your fax > Done
This setting can be especially useful in sending information to fax lines that are not readily available during certain hours, or when transmission times are cheaper.
Touching the Advanced Options button opens a screen where you can change the following settings:
Faxing 111

This option lets you hold received faxes from printing until they are released. Held faxes can be released manually or at a scheduled day or time.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > Fax Settings > Analog Fax Setup > Holding Faxes.
3 In the Print Faxes Password field, enter a password.
5 If you selected Scheduled, then continue with the following steps: a Click Fax Holding Schedule. b From the Action menu, select Hold faxes.
c From the Time menu, select the time you want the held faxes released. d From the Day(s) menu, select the day you want the held faxes released.
6 Click Add.
This option lets you print and forward received faxes to a fax number, e‑mail address, FTP site, or LDSS.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings > Fax Settings.
Faxing 112

5 In the Forward to Shortcut field, enter the shortcut number where you want the fax forwarded.
6 Click Submit.
Faxing 113

Scanning to an FTP address 114

Use the ADF for multiple‑page documents. Use the scanner glass for single pages, small items (such as postcards or
photos), transparencies, photo paper, or thin media (such as magazine clippings).
The scanner lets you scan documents directly to a File Transfer Protocol (FTP) server. Only one FTP address may be sent to the server at a time.
Once an FTP destination has been configured by your system support person, the name of the destination becomes available as a shortcut number, or it is listed as a profile under the Held Jobs icon. An FTP destination could also be another PostScript printer; for example, a color document can be scanned, and then sent to a color printer. Sending a document to an FTP server is similar to sending a fax. The difference is that you are sending the information over your network instead of over the phone line.
Instead of entering the entire FTP site address on the printer control panel each time you want to send a document to an FTP server, you can create a permanent FTP destination and assign a shortcut number. There are two methods for creating shortcut numbers: using using the Embedded Web Server and using the printer touch screen.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings.

Scanning to an FTP address 115
3 Under Other Settings, click Manage Shortcuts.
4 Click FTP Shortcut Setup.
5 Enter the appropriate information.
6 Enter a shortcut number.
If you enter a number that is already in use, then you are prompted to select another number.
7 Click Add.
1 From the home screen, navigate to:
FTP > type the FTP address >
> enter a name for the shortcut > Done
2 Verify that the shortcut name and number are correct, and then touch OK. If the name or number is incorrect, then touch Cancel, and then reenter the information.
If you enter a number that is already in use, then you are prompted to select another number.
3 Touch Submit.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 From the home screen, navigate to:
FTP > FTP > type the FTP address > Send It
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 Press # , and then enter the FTP shortcut number.
4 Touch Send It.

Scanning to an FTP address 116
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, adjust the paper guides.
3 From the home screen, navigate to:
> enter the name of recipient > Browse shortcuts > name of recipient > Search
This option lets you enter the IP address for the FTP destination.
This option lets you enter the file name of the scanned document.
This option opens a screen where you can choose the size of the documents for FTP sending.
This option sets the output (PDF, TIFF, JPEG or XPS) for the scanned image.
This option enables or disables color for the scanned image.

Scanning to an FTP address 117
This option adjusts the output quality of your file. Increasing the image resolution increases the file size and the time needed to scan your original document. Image resolution can be decreased to reduce the file size.
This option lets you change the Sides (Duplex), Orientation, and Binding.
This option lets you specify the content type and source of the original document.
Choose content type from Text, Text/Photo, Photo, or Graphics.
Choose content source from Color Laser, Black/White Laser, Inkjet, Photo/Film, Magazine, Newspaper, Press, or Other.
This option displays the first page of the original document before it is scanned completely. When the first page is scanned, the scanning is paused and a preview image appears.

Scanning to an FTP address 118
Touching the Advanced Options button opens a screen where you can change the following settings:

Scanning to a computer or flash drive 119

Use the ADF for multiple‑page documents. Use the scanner glass for single pages, small items (such as postcards or
photos), transparencies, photo paper, or thin media (such as magazine clippings).
The scanner lets you scan documents directly to a computer or to a flash drive. The computer does not have to be directly connected to the printer for you to receive Scan to PC images. You can scan the document back to the computer over the network by creating a scan profile on the computer, and then downloading the profile to the printer.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Scan Profile > Create.
3 Select your scan settings, and then click Next.
4 Select a location on your computer where you want to save the scanned output file.
5 Enter a scan name.
The scan name is the name that appears in the Scan Profile list on the display.
6 Click Submit.
7 Review the instructions on the Scan Profile screen.

Scanning to a computer or flash drive 120
A shortcut number was automatically assigned when you clicked Submit. You can use this shortcut number when you are ready to scan your documents.
a Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
c Press # , and then enter the shortcut number using the keypad, or touch Held Jobs on the home screen, and then touch Profiles. d After entering the shortcut number, the scanner scans and sends the document to the directory or program
you specified. If you touched Profiles on the home screen, then locate your shortcut on the list.
8 Return to the computer to view the file.
The output file is saved in the location or launched in the program you specified.
1 Load an original document faceup, short edge first into the ADF or facedown on the scanner glass.
2 If you are loading a document into the ADF, then adjust the paper guides.
3 Insert the flash drive into the USB port on the front of the printer.
The USB Drive home screen appears.
4 Select the destination folder, and then touch Scan to USB drive.
5 Adjust the scan settings.
6 Touch Scan It.
You can use the LexmarkTM ScanBackTM Utility to create scan‑to‑PC profiles. The ScanBack Utility can be downloaded from the Lexmark Web site on http://support.lexmark.com.
1 Set up a scan‑to‑PC profile: a Launch the ScanBack Utility. b Select the printer.
If no printers are listed, then contact your system support person, or click Setup to manually search for an IP address or host name. c Follow the instructions on your computer screen to define the type of document being scanned and what kind of output you want to create.

Scanning to a computer or flash drive 121
d Select any of the following:
A dialog box appears with your scan profile information and the status of the received images.
2 Scan original documents: a Load all pages in the ADF or on the scanner glass. b From the printer control panel, navigate to:
Scan/Email > Profiles > select your scan profile > Submit
This option sets the size of the documents you are going to scan. When Original Size is set to Mixed Sizes, you can scan an original document that contains mixed paper sizes (letter‑ and legal‑size pages).
This option adjusts the output quality of your file. Increasing the image resolution increases the file size and the time needed to scan your original document. Image resolution can be decreased to reduce the file size.
This option enables or disables color for the scanned image.
This option lets you specify the content type and source of the original document.
Choose content type from Text, Text/Photo, Photo, or Graphics.
Choose content source from Color Laser, Black/White Laser, Inkjet, Photo/Film, Magazine, Newspaper, Press, or Other.

Scanning to a computer or flash drive 122
This option adjusts how light or dark your scanned documents will turn out in relation to the original document.
This option lets you change the Sides (Duplex), Orientation, and Binding.
This option displays the first page of the image before it is included in the e-mail. When the first page is scanned, the scanning is paused and a preview image appears.
Touching the Advanced Options button opens a screen where you can change the following settings:

Understanding printer menus 123
Menus list
These menus can be accessed from the printer control panel, the Embedded Web Server, or the software application driver.
Supplies Paper Menu Reports Settings
E‑mail Settings
Network [x] Setup Page
Black Cartridge Imaging Kit
Paper Weight Paper Loading
Shortcut List Fax Job Log
FTP Settings Flash Drive
Separator Roll and Pick Assembly
Print Fonts Print Directory
Security Network/Ports Help Manage Shortcuts
Edit Security Setups Miscellaneous Security Settings
Print All Guides Copy Guide
Fax Shortcuts E-mail Shortcuts
Set Date and Time
A list of installed DLEs (Download Emulators) appears.2
1 Depending on the printer setup, this menu appears as Standard Network or Network [x].
2 This menu appears only when one or more DLEs are installed.

Understanding printer menus 124
Shows the status of the cyan toner cartridge
Early Warning Low Invalid Replace Missing or Defective OK Unsupported
Shows the status of the magenta toner cartridge
Early Warning Low Invalid Replace Missing or Defective OK Unsupported
Shows the status of the yellow toner cartridge
Early Warning Low Invalid Replace Missing or Defective OK Unsupported
Shows the status of the black toner cartridge
Early Warning Low Invalid Replace Missing or Defective OK Unsupported
Shows the status of the imaging kit
OK Replace Black Imaging Kit Replace Color Imaging Kit
Separator Pick Assembly and Roller
Shows the status of the separator pick assembly and roller

Understanding printer menus 125
Shows the status of the waste toner bottle
Near Full Replace Missing OK
Sets a default paper source for all print jobs
Tray [x] MP feeder Manual Paper Manual Envelope
Specifies the paper size loaded in each tray
Letter Legal Executive Oficio (México) Folio Universal A4 A5 JIS B5

Understanding printer menus 126
Specifies the type of paper loaded in each tray
Plain Paper Card Stock Transparency Recycled Glossy Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Custom Type [x]
Specifies the paper size loaded in the multipurpose feeder
Letter Legal Executive Oficio (México) Folio Statement Universal 7 3/4 Envelope 9 Envelope 10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope A4 A5 A6 JIS B5
Menu item Description · Tray [x] Type · MP Feeder Size

Understanding printer menus 127
Specifies the paper type loaded in the multipurpose feeder
Custom Type [x] Plain Paper Card Stock Transparency Recycled Glossy Labels Bond Envelope Letterhead Preprinted Colored Paper Light Paper Heavy Paper
Specifies the paper size being loaded manually
Letter Legal Executive Oficio (México) Folio Statement Universal A4 A5 A6 JIS B5
Specifies the paper type being loaded manually
Plain Paper Card Stock Transparency Recycled Glossy Labels Bond Letterhead Preprinted Colored Paper Light Paper Heavy Paper Custom Type [x]

Understanding printer menus 128
Specifies the envelope size being loaded manually
10 Envelope DL Envelope C5 Envelope B5 Envelope Other Envelope 7 3/4 Envelope 9 Envelope
Specifies the envelope type being loaded manually
Envelope Custom Type [x]
Substitutes a specified paper size if the requested paper size is not available
All Listed Off Statement/A5 Letter/A4
Specifies the relative texture of the paper loaded
Specifies the relative texture of the card stock loaded
Specifies the relative texture of the transparencies loaded

Understanding printer menus 129
Specifies the relative texture of the recycled paper loaded
Specifies the relative texture of the glossy paper loaded
Specifies the relative texture of the labels loaded
Specifies the relative texture of the bond paper loaded
Specifies the relative texture of the envelopes loaded
Specifies the relative texture of the letterhead paper loaded
Specifies the relative texture of the preprinted paper loaded
Specifies the relative texture of the colored paper loaded
Specifies the relative texture of the light paper loaded
Specifies the relative texture of the heavy paper loaded
Specifies the relative texture of the rough/cotton paper loaded

Understanding printer menus 130
Specifies the relative texture of the custom paper loaded
Identifies the relative weight of the paper loaded
Identifies the relative weight of the card stock loaded
Identifies the relative weight of the transparency loaded
Identifies the relative weight of the recycled paper loaded
Identifies the relative weight of the glossy paper loaded
Identifies the relative weight of the labels loaded
Identifies the relative weight of the bond paper loaded

Understanding printer menus 131
Identifies the relative weight of the envelopes loaded
Identifies the relative weight of the envelopes loaded
Identifies the relative weight of the letterhead loaded
Identifies the relative weight of the preprinted paper loaded
Identifies the relative weight of the paper loaded
Identifies the relative weight of the paper loaded
Identifies the relative weight of the paper loaded

Understanding printer menus 132
Identifies the relative weight of the rough/cotton paper loaded
Identifies the relative weight of the custom paper type loaded
Determines whether 2‑sided printing occurs for all print jobs that specify Card Stock as the paper type
Determines whether 2‑sided printing occurs for all print jobs that specify Recycled as the paper type
Determines whether 2‑sided printing occurs for all print jobs that specify Glossy as the paper type
Determines whether 2‑sided printing occurs for all print jobs that specify Bond as the paper type
Determines whether 2‑sided printing occurs for all print jobs that specify Letterhead as the paper type
Determines whether 2‑sided printing occurs for all print jobs that specify Preprinted as the paper type

Understanding printer menus 133
Determines whether 2‑sided printing occurs for all print jobs that specify Colored as the paper type
Determines whether 2‑sided printing occurs for all print jobs that specify Light as the paper type
Determines whether 2‑sided printing occurs for all print jobs that specify Heavy as the paper type
Determines whether 2‑sided printing occurs for all print jobs that specify Custom [x] as the paper type
Associates a paper or specialty media type with a factory‑default Custom Type [x] name or a user‑defined custom name created from the Embedded Web Server or using MarkVisionTM Professional
Paper Card Stock Transparency Glossy Rough/Cotton Labels Envelope
Specifies a paper type when the Recycled setting is selected in other menus
Paper Card Stock Transparency Glossy Rough/Cotton Labels Envelope

Understanding printer menus 134
Specify a custom name for a paper type. This name replaces the Custom Type [x] name in the printer menus.
Custom Scan Size [x]
Specifies a custom scan size name, scan sizes, and options. The custom scan size name replaces Custom Scan Size [x] in the printer menus.
Scan Size Name Width
1–11.69 inches (25–297 mm) Height
1–17 inches (25–432 mm) Orientation
Portrait Landscape 2 scans per side Off On
Identifies the unit of measure
Sets the portrait width
3–14.17 inches 76–360 mm

Understanding printer menus 135
Sets the portrait height
3–14.17 inches 76–360 mm
Specifies the feed direction
Short Edge Long Edge
Menu Settings Page Prints a report containing information about the paper loaded into trays, installed memory, total page count, alarms, timeouts, printer control panel language, TCP/IP address, status of supplies, status of the network connection, and other information
Device Statistics Prints a report containing printer statistics such as supply information and details about printed pages
Network Setup Page Prints a report containing information about the network printer settings, such as the TCP/IP address information
Shortcut List Prints a report containing information about configured shortcuts
Fax Job Log Prints a report containing information about the last 200 completed faxes
Fax Call Log Prints a report containing information about the last 100 attempted, received, and blocked calls
Copy Shortcuts Prints a report containing information about copy shortcuts
E‑mail Shortcuts Prints a report containing information about e‑mail shortcuts
Fax Shortcuts Prints a report containing information about fax shortcuts
![Page 136 of the Lexmark X548 user manual — Standard Network or Network [x] menu](/cdn/reader/4e/4e361cbfc4ffd5e542d96fb0dd38ca3d4b5c75af269e4915b54558ccd23ba126/images/page-136.webp?w=400)
Understanding printer menus 136
FTP Shortcuts Prints a report containing information about FTP shortcuts
Profiles List Prints a list of profiles stored in the printer
Print Fonts Prints a report of all the fonts available for the printer language currently set in the printer
Print Directory Prints a list of all the resources stored on an optional flash memory card or printer hard disk
Asset Report Prints a report containing asset information including the printer serial number and model name. The report contains text and UPC barcodes that can be scanned into an asset database.
Auto [list of available network cards]
Sets the printer to automatically switch to PCL emulation when a print job requires it, regardless of the default printer language

Understanding printer menus 137
Sets the printer to automatically switch to PS emulation when a print job requires it, regardless of the default printer language
Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol
Sets the size of the network input buffer
Auto 3KB to [maximum size allowed]
Temporarily stores print jobs on the printer hard disk before printing. This menu only appears if a formatted printer hard disk is installed.
Sets the printer to process Macintosh binary PostScript print jobs

Understanding printer menus 138
Displays and sets the printer network settings
Reports Network Card TCP/IP IPv6 AppleTalk
Reports Network Card TCP/IP IPv6 AppleTalk
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network [x] > Standard Network Setup or Network Setup > Reports or Network Reports
Print Setup Page Prints a report containing information about the network printer settings, such as the TCP/IP address
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network [x] > Standard Network Setup or Network [x] Setup > Network Card
Lets you view the connection status of the Network Card
View Card Speed Lets you view the speed of a currently active network card
Lets you view the network addresses
Sets the amount of time in seconds before a network print job is canceled
Allows the printer to print a banner page

Understanding printer menus 139
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network [x] > Standard Network Setup or Network [x] Setup > TCP/IP
Set Hostname Lets you view or change the current TCP/IP host name
IP Address Lets you view or change the current TCP/IP address
Netmask Lets you view or change the current TCP/IP netmask
Gateway Lets you view or change the current TCP/IP gateway
Specifies the DHCP address and parameter assignment setting
Specifies the RARP address assignment setting
Specifies the BOOTP address assignment setting
Specifies the Zero Configuration Networking setting
Enables the built-in FTP server, which allows you to send files to the printer using File Transfer Protocol.
Enables the built-in web server (Embedded Web Server) to monitor and manage the printer remotely using a web browser.
WINS Server Address Lets you view or change the current WINS server address
Lets you view or change the current DDNS setting

Understanding printer menus 140
Lets you view or change the current mDNS setting
DNS Server Address Lets you view or change the current DNS server address
Lets you view or change the current HTTPS setting
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network [x] > Standard Network Setup or Network [x] Setup > IPv6
Enables IPv6 in the printer
Specifies whether the network adapter accepts the automatic IPv6 address configuration entries provided by a router
Set Hostname Lets you view or change the current IPv6 host name
View Address Lets you view the current setting
Enables DHCPv6 in the printer
This menu is available from the Network/Ports menu:
Network/Ports > Standard Network or Network [x] > Standard Network Setup or Network [x] Setup > AppleTalk
View Name Shows the assigned AppleTalk name

Understanding printer menus 141
View Address Shows the assigned AppleTalk address
Provides a list of AppleTalk zones available on the network
[default] [list of zones available on the network]
Sets the printer to automatically switch to PCL emulation when a print job received through a USB port requires it, regardless of the default printer language
Sets the printer to automatically switch to PS emulation when a print job received through a USB port requires it, regardless of the default printer language
Sets the printer to perform the special processing required for bidirectional communication following the conventions defined by the NPA protocol

Understanding printer menus 142
Sets the size of the USB input buffer
Auto 3KB to [maximum size allowed] Disabled
Temporarily stores print jobs on the printer hard disk before printing
Sets the printer to process Macintosh binary PostScript print jobs
Sets the network address information for an external print server
yyy.yyy.yyy.yyy
Sets the netmask information for an external print server
yyy.yyy.yyy.yyy
Sets the gateway information for an external print server
yyy.yyy.yyy.yyy

Understanding printer menus 143
Primary SMTP Gateway Specifies SMTP server gateway and port information
Secondary SMTP Gateway Port
5–30 Specifies the amount of time in seconds before the server stops trying to send an e‑mail
Reply Address Specifies a reply address of up to 128 characters in the e-mail sent by the printer
Sets the printer to use SSL for increased security when connecting to the SMTP server
Specifies the type of user authentication required for scan to e‑mail privileges
No authentication required Login/Plain CRAM‑MD5 Digest‑MD5 NTLM Kerberos 5
Device‑Initiated E‑mail
Specifies what credentials will be used when communicating to the SMTP server. Some SMTP servers require credentials to send an e-mail.
None Use Device SMTP Credentials
User‑Initiated E‑mail
None Use Device SMTP Credentials Use Session User ID & Password Use Session E‑mail address & Password Prompt User

Understanding printer menus 144
Edit Backup Password Creates a backup password
Edit Building Blocks Edits the Internal Accounts, NTLM, various Setups, Password, and PIN
Edit Security Templates Adds or edits a Security Template
Edit Access Controls Controls access to printer menus, firmware updates, held jobs, and other access points
Limits the number and time frames of failed login attempts from the printer control panel before all users are locked out
Login failures Failure time frame Lockout time Panel Login Timeout Remote Login Timeout
Changes the value of the security settings
Access controls = “No Security” Reset factory security defaults No Effect

Understanding printer menus 145
Allows the user to request a server certificate
Demand Try Allow Never
1‑16 Limits the digit length of the PIN
Limits the number of times an invalid PIN can be entered
Limits the amount of time a confidential print job stays in the printer before it is deleted
Off 1 hour 4 hours 24 hours 1 week
Sets a time limit on how long the printer stores print jobs
Off 1 hour 4 hours 24 hours 1 week
Sets a time limit on how long the printer stores print jobs needing verification
Off 1 hour 4 hours 24 hours 1 week

Understanding printer menus 146
Sets a time limit on how long the printer stores print jobs for printing at a later time
Off 1 hour 4 hours 24 hours 1 week
Disk Wiping erases only print job data on the printer hard disk that are not currently in use by the file system. All permanent data on the printer hard disk are preserved, such as downloaded fonts, macros, and held jobs.
Specifies the mode for disk wiping
Sets the schedule for disk wiping
Overwrites all disk space that has been used to hold data from a print job that has been processed (printed). This type of wipe does not erase any information related to an unprocessed print job.
Do not start now Start now

Understanding printer menus 147
Marks all disk space used by a previous print job and does not permit the file system to reuse this space until it has been cleared
Single pass Multiple pass
Allows the file system to reuse marked disk space without having to wipe it first
Single pass Multiple pass
Allows the file system to reuse marked disk space without having to wipe it first
Single pass Multiple pass
Export Log Enables an authorized user to export the security log
Specifies whether audit logs are deleted

Understanding printer menus 148
Specifies whether and how the audit logs are created
Enable Audit Enable Remote Syslog Remote Syslog Server Remote Syslog Port Remote Syslog Method Remote Syslog Facility Log full behavior Admin’s e-mail address Digitally sign exports Severity of events to log Remote Syslog non-logged events E-mail log cleared alert E-mail log wrapped alert E-mail % full alert % full alert level E-mail log exported alert E-mail log settings changed alert Log line endings
Current Date and Time Lets you view the current date and time settings for the printer
Manually Set Date and Time
[input date and time]
[list of time zones]
Custom Time Zone Setup
Enables the user to setup the time zone
UTC Offset DST Start Week DST Start Day DST Start Month DST Start Time DST End Week DST End Day DST End Month DST End Time DST Offset

Understanding printer menus 149
Enables Network Time Protocol, which synchronizes the clocks of devices on a network
Lets you view the NTP Server Address
Lets you change the authentication setting to On or Off
Sets the language of the text appearing on the display
English Francais Deutsch Italiano Espanol Dansk Norsk Nederlands Svenska Portuguese Suomi Russian Polski Greek Magyar Turkce Cesky Simplified Chinese Traditional Chinese Korean Japanese

Understanding printer menus 150
Minimizes the use of energy, paper, or specialty media
Off Energy Energy/Paper Paper
Specifies whether the ADF sounds a beep when paper is loaded
Reduces the amount of noise produced by the printer
Instructs the printer to run the setup wizard

Understanding printer menus 151
Specifies a language for the printer control panel virtual keyboard
English Francais Francais Canadien Deutsch Italiano Espanol Greek Dansk Norsk Nederlands Svenska Suomi Portuguese Russian Polski Swiss German Swiss French Korean Magyar Turkish Czech Simplified Chinese Traditional Chinese Japanese Custom Key 1 Custom Key 2
Specifies the default paper measurements
Scan to PC Port Range
Specifies a valid port range for printers behind a port blocking firewall. The valid ports are specified by two sets of numbers separated by a semicolon.

Understanding printer menus 152
Specifies what is displayed on the upper left and right corners of the home screen
Left side Right side Custom Text [x] [x] Toner Waste Toner Bottle
For the Left side and Right side options, choose from the following options:
None IP Address Hostname Contact Name Location Date/Time mDNS/DDNS Service Name Zero Configuration Name Custom Text [x] Model Name
Do not display Display Message to Display
Specifies what is displayed for Paper Jam, Load Paper, and Service Errors. Available selections for each button are:
Paper Jam Load Paper Service Errors
No Yes Message to Display

Understanding printer menus 153
Lets you add or remove buttons that appear on the home screen
Change Language Copy Copy shortcuts Fax Fax Shortcuts E‑mail E‑mail Shortcuts FTP FTP Shortcuts Search Held Jobs Held Jobs USB Drive Profiles and Solutions Bookmarks Jobs by user Forms and Favorites
Available selections for each button are:
Do not display Display
Specifies the format for the printer date
MM‑DD‑YYYY DD‑MM‑YYYY YYYY‑MM‑DD
Specifies the format for the printer time
12 hour A.M./P.M. 24 hour clock
20–100 Specifies the brightness of the printer control panel display
Sets copying from the scanner glass to only one page at a time
Sets the audio volume for the buttons
Specifies whether bookmarks are displayed from the Held Jobs area
Specifies whether image background is removed in copy, fax, e‑mail, FTP, or scan‑to‑USB jobs

Understanding printer menus 154
Allow Custom Job Scans
Lets you scan multiple documents into one file
Specifies how a scan job should be reloaded if a paper jam occurs in the ADF
Job level Page level
Web Page Refresh Rate
30–300 Specifies the number of seconds between Embedded Web Server refreshes
Contact Name Specifies a contact name for the printer
Location Specifies the location of the printer
Sets an alarm to sound when the printer requires operator intervention
Alarm Control Cartridge Alarm
Available selections for each alarm type are:
Specifies the number of minutes of inactivity before the system enters a lower power state

Understanding printer menus 155
Sets the amount of time the printer waits, after a print job is finished, before it goes into a reduced power state
Sets the amount of time in seconds the printer waits before returning the printer display to a Ready state
Sets the amount of time in seconds the printer waits to receive an end‑of‑job message before canceling the remainder of the print job
Sets the amount of time in seconds the printer waits for additional data before canceling a print job
Sets the amount of time the printer waits for user intervention before it holds jobs that require unavailable resources and continues to process print jobs in the print queue

Understanding printer menus 156
Lets the printer automatically continue printing from certain offline situations when not resolved within the specified time period
Specifies whether the printer reprints jammed pages
Lets the printer successfully print a page that may not have printed otherwise
Determines how the printer responds when pressing the Sleep button in Idle state
Returns the printer settings to the factory default settings
Do Not Restore Restore Now

Understanding printer menus 157
Specifies the type of content in the copy job
Text/Photo Photo Text Graphics
Specifies how the original document was produced
Color Laser Inkjet Photo/Film Magazine Newspaper Press Black and White Laser Other
Specifies whether copies are scanned in color
Specifies whether copies are printed in color
Specifies whether an original document is duplex (two‑sided) or simplex (one- sided), and then specifies whether the copy should be duplex or simplex
1 sided to 1 sided 1 sided to 2 sided 2 sided to 1 sided 2 sided to 2 sided
Allows copying two or four sheets of a document on one page
Off 2 on 1 Portrait 2 on 1 Landscape 4 on 1 Portrait 4 on 1 Landscape

Understanding printer menus 158
Specifies whether a page border is printed
Keeps the pages of a print job stacked in sequence when printing multiple copies
On [1,2,1,2,1,2] Off [1,1,1,2,2,2]
Specifies the paper size of the original document
Letter Legal Executive Folio Statement Universal 4 x 6 in. 3 x 5 in. Business Card ID Card Custom Scan Size [x] A4 A5 Oficio (Mexico) A6 JIS B5 Book Original Mixed Sizes
Specifies the paper source for copy jobs
Tray [x] Single Sheet Feeder Multi‑Page Feeder
Places a sheet of paper between transparencies
Places a sheet of paper between pages, copies, or copy jobs
Off Between Copies Between Jobs Between Pages
Specifies the separator sheet source
Tray [x] Manual Feeder
1–9 Specifies the level of darkness for the copy job

Understanding printer menus 159
1–999 Specifies the number of copies for the copy job
Specifies header/footer information and its location on the page For the location, choose from the following options:
Off Date/Time Page number Custom text Print on
All pages First page only All but first page Custom text
Specifies the overlay text printed on each page of the copy job
Off Confidential Copy Draft Urgent Custom
Custom Overlay Specifies a custom overlay text
Allows interruption of a print job to copy a page or document
Lets you copy, in a single copy job, a document that contains mixed paper sizes
Allow Save as Shortcut
Lets you save custom copy settings as shortcuts
Adjusts the amount of background visible on a copy job
‑4 to 4
Lets you automatically center the content on the page

Understanding printer menus 160
Enables an equal balance of colors in the output
Cyan - Red Magenta - Green Yellow - Blue
Specifies which color to drop during copy jobs, and how much increase or decrease there is in the dropout
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specifies the contrast used for the copy job
Best for Content 0–5
Creates a mirror image of the original document
Creates a negative image of the original document
Adjusts the amount of shadow detail visible on a copy job
‑4 to 4
Specifies if the original document is scanned edge-to‑edge
Scan edge to edge
1–5 Adjusts the amount of sharpness of a copy job
Enables the user to specify “warm” or “cool” outputs. "Cool” values generate a bluer output than the default, while “warm” values generate a redder output than the default.
‑4 to 4
Creates a sample copy of the original document

Understanding printer menus 161
Analog Fax Setup mode sends the fax job by way of a telephone line.
Fax Name or Station Name Specifies the name of the fax in the printer
Fax Number or Station Number Specifies the number assigned to the fax
Specifies how the fax is identified
Fax Name or Station Name Fax Number or Station Number
Sets the printer to fax manually only, which requires a line splitter and a telephone handset
Defines the allocation of non-volatile memory between sending and receiving fax jobs
Equal Mostly sent All send All receive Mostly receive
Specifies whether or not the printer cancels fax jobs
Specifies type of caller ID being used
Specifies the direction from where digits are masked in an outgoing fax number
Off From left From right
0–58 Specifies the number of digits to mask in an outgoing fax number

Understanding printer menus 162
Configures the fax cover page
Off by default On by default Never use Always use Include to field
On Off Include from field
Off On From Include Message field
Off On Message Include Logo
Off On Include Footer [x]
Specifies quality in dots per inch (dpi). A higher resolution gives greater print quality, but increases the fax transmission time for outgoing faxes.
Standard Fine 200 dpi Super Fine 300 dpi

Understanding printer menus 163
Specifies the paper size of the original document
Mixed Sizes Letter Legal Executive Tabloid Folio Statement Universal 4 x 6 in. 3 x 5 in. Business Card Custom Scan Size [x] A3 A4 A5 Oficio (Mexico) A6 JIS B4 JIS B5 Book Original
Specifies how text and graphics are oriented on a page
Off Long edge Short edge
Specifies the content of the original document
Text Text/Photo Graphics Photo
Specifies how the original document was produced
Color Laser Inkjet Magazine Press Black/White Laser Photo/Film Newspaper Other

Understanding printer menus 164
1–9 Lightens or darkens the output
Dial Prefix Lets you enter a dialing prefix, such as 99. A numeric entry field is provided.
Establishes a dialing prefix rule
0–9 Specifies the number of times the printer tries to send the fax to a specified number
1–200 Specifies the number of minutes between redials
Enables switchboard blind dialing without a dial tone
Enables Error Correction Mode for fax jobs
Lets you fax files that are scanned at the printer
Allows the printer driver to send fax jobs
Allow Save as Shortcut
Lets you save fax numbers as shortcuts in the printer
Specifies the dialing sound, either as a tone or a pulse
Specifies the maximum speed in baud at which faxes are sent
2400 4800 9600 14400 33600
Lets you scan a document that contains mixed paper sizes into a single file
Specifies whether a preview will appear on the display for scan jobs

Understanding printer menus 165
Adjusts the amount of background visible on a scanned image
‑4 to 4
Enables an equal balance of colors in the scanned image
Cyan - Red Magenta - Green Yellow - Blue
Specifies which color to drop, and how much to increase or decrease the dropout
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specifies the contrast in the scanned image
Best for content 0–5
Creates a mirror image of the original document
Creates a negative image of the original document
Adjusts the amount of shadow detail visible
‑4 to 4
Specifies if the original document is scanned edge-to‑edge prior to faxing
Scan edge to edge
0–5 Adjusts the sharpness of a fax
Enables the user to specify “warm” or “cool” outputs. "Cool” values generate a bluer output than the default while “warm” values generate a redder output than the default.
‑4 to 4
Enable Color Fax Scans
Off by default On by default Never use Always use

Understanding printer menus 166
Auto Convert Color Faxes to Mono Faxes
Converts all outgoing faxes to black and white
Allows fax jobs to be received by the printer
1–25 Specifies the number of rings before answering an incoming fax job
Scales an incoming fax job so that it fits the size of the paper loaded in the designated fax source
Specifies the paper source selected to supply paper for the printer to print an incoming fax
Auto Tray [x] Multi‑Purpose Feeder
Specifies an exit bin for received faxes
Standard Bin Bin [x]
Enables duplex printing (two-sided printing) for incoming fax jobs
Enables the printer to include separator sheets for incoming fax jobs
Off Before Job After Job
Specifies where the printer will pick the separator sheet
Tray [x] Manual Feeder
Prints the transmission information at the bottom of each page from a received fax
Specifies the maximum speed in baud at which faxes are received
33600 2400 4800 9600 14400

Understanding printer menus 167
Enables forwarding of received faxes to another recipient
Print Print and Forward Forward
Specifies the type of recipient to which faxes will be forwarded
Fax E‑mail FTP LDSS eSF
Forward to Shortcut Lets you enter the shortcut number which matches the recipient type (Fax, E-mail, FTP, LDSS, or eSF)
Block No Name Fax
Enables blocking of incoming faxes sent from devices with no station ID specified
Banned Fax List Enables the list of banned fax numbers stored in the printer
Enables fax holding all of the time or according to set schedule
Off Always On Manual Scheduled Fax Holding Schedule
Enable Color Fax Receive
Enables the device to receive fax in color
Enables printing of a transmission log after each fax job
Print log Do not print log Print only for error
Enables printing of a receive error log following a receive error
Print Never Print on Error
Enables automatic printing of fax logs

Understanding printer menus 168
Specifies the source of the paper used for printing logs
Tray [x] Manual Feeder
Specifies whether printed logs display the dialed number or the station name returned
Remote Fax Name or Remote Station Name Dialed Number
Enables access to the Fax Job log
Enables access to the Fax Call log
Specifies the exit bin where fax logs are printed
Standard Bin Bin [x]
Specifies the mode of the speaker.
On until Connected Always On Always Off
Controls the volume setting
Controls the fax speaker ringer volume
All Rings Single Ring Only Double Ring Only Triple Ring Only Single or Double Rings Only Single or Triple Rings Only Double or Triple Rings Only
Specifies ring patterns when device is answering calls

Understanding printer menus 169
Fax Mode sends the fax job to a fax server for transmission.
To Format Lets you enter specific fax information using the virtual keyboard on the printer control panel Reply Address
SMTP Setup Specifies SMTP setup information
Primary SMTP Gateway Specifies SMTP server port information
Specifies the image type for scanning to fax
PDF (.pdf) XPS (.xps) TIFF (.tif)
This option tells the printer the original document type and source.
Text/Photo Photo Text Graphics
Specifies how the content was originally produced
Color Laser Inkjet Photo/Film Magazine Newspaper Press Black and White Laser Other
Specifies the resolution level for scanning to fax
Standard Fine 200 dpi Super Fine 300 dpi
1–9 Lightens or darkens the output
Specifies the orientation of the scanned image

Understanding printer menus 170
Specifies the paper size of the document being scanned
Mixed Sizes Letter Legal Executive Folio Statement Universal 4 xn 6 in. 3 x 5 in. Business Card Custom Scan Size [x] A4 A5 A6 Oficio (Mexico) JIS B5 Book Original Mixed Sizes
Use Multi‑Page TIFF
Lets you save scan jobs into multiple‑page or single-page TIFF files. For a multiple- page scan‑to‑fax job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the scan job.
Enables receiving of analog faxes
E‑mail Server Setup
Specifies e‑mail server information
Subject Message Base file name
E‑mail Server Setup
Sends a copy of the e-mail back to the sender
Send me a copy
Never appears On by default Off by default Always On

Understanding printer menus 171
E‑mail Server Setup
Specifies the maximum e-mail size in kilobytes
Max E‑mail size
E‑mail Server Setup
Sends a message when an e-mail is greater than the configured size limit
E‑mail Server Setup
Specifies a domain name, such as a company domain name, and then limits e‑mail destinations to that domain name only
E‑mail Server Setup
Defines the e‑mail server path name; for example: /directory/path
Server Login Password Path Base file name Web Link
Specifies the format of the scanned file
PDF (.pdf) Secure PDF TIFF (.tif) JPEG (.jpg) XPS (.xps)
Sets the version of the PDF file that will be scanned for e‑mailing
1.5 1.6 A‑1a 1.2 1.3 1.4
Specifies the content of the original document
Text/Photo Photo Text Graphics

Understanding printer menus 172
Specifies how the original document was produced
Color Laser Inkjet Magazine Press Black/White Laser Photo/Film Newspaper Other
Specifies whether or not a job prints in grayscale or color
Specifies the resolution of the scan in dots per inch
150 200 300 400 600 75
1–9 Lightens or darkens the output
Specifies the orientation of the scanned image

Understanding printer menus 173
Specifies the paper size of the document being scanned
Letter Legal Executive Tabloid Folio Statement Universal 4 x 6 in. 3 x 5 in. Business Card Custom Scan Size [x] A3 A4 A5 Oficio (Mexico) A6 JIS B4 JIS B5 Book Original Mixed Sizes
Specifies how the text and graphics are oriented on the page
Off Long edge Short edge
Sets the quality of a JPEG photo image in relation to file size and quality of the image
Best for content 5–90
5–90 Sets the quality of a text image in relation to file size and quality of the image
5–90 Sets the quality of a text or photo image in relation to file size and the quality of the image
5–90 Sets the quality of a photo image in relation to file size and the quality of the image

Understanding printer menus 174
E‑mail images sent as
Specifies how the images will be sent
Use Multi‑Page TIFF
Provides a choice between single-page TIFF files and multiple‑page TIFF files. For a multiple-page scan‑to‑e-mail job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.
Specifies whether or not the transmission log prints
Print log Do not print log Print only for error
Specifies the paper source for printing e-mail logs
Tray [x] Manual Feeder
E‑mail Bit Depth
Enables the Text/Photo mode to produce smaller file sizes by using 1‑bit images when Color is set to Off
8 bit 1 bit
Lets you copy, in a single copy job, a document that contains mixed paper sizes
Specifies whether or not a preview will appear on the display for scan jobs
Allow Save as Shortcut
Lets you save e-mail addresses as shortcuts
Adjusts the amount of background visible on a scanned image
‑4 to 4
Enables an equal balance of colors in the output
Cyan - Red Magenta - Green Yellow - Blue

Understanding printer menus 175
Specifies which color to drop during scanning, and how much to increase or decrease the dropout
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specifies the contrast of the output
Best for content 0–5
Creates a mirror image of the original document
Creates a negative image of the original document
Adjusts the amount of shadow detail visible on a scanned image
‑4 to 4
Scan edge to edge
Specifies whether the original document is scanned edge-to-edge
1–5 Adjusts the amount of sharpness on a scanned image
Enables the user to specify “warm” or “cool” outputs. "Cool” values generate a bluer output than the default while “warm” values generate a redder output than the default.
‑4 to 4
Use cc:/bcc:
Enables the use of the cc: and bcc: fields

Understanding printer menus 176
Specifies the format of the FTP file
PDF (.pdf) Secure PDF (.pdf) TIFF (.tif) JPEG (.jpg) XPS (.xps)
Sets the version level of the PDF file for FTP sending
1.5 1.6 A‑1a 1.2 1.3 1.4
Specifies the content of the original document
Text Graphics Text/Photo Photo
Specifies how the original document was produced
Color Laser Inkjet Magazine Press Black/White Laser Photo/Film Newspaper Other
Specifies whether a job prints in grayscale or color
Specifies how many dots per inch are scanned
150 200 300 400 600 75
1–9 Lightens or darkens the output

Understanding printer menus 177
Specifies the orientation of the scanned image
Specifies the paper size of the document that is being scanned
Letter Legal Executive Tabloid Folio Statement Universal 4 x 6 in. 3 x 5 in. Business Card Custom Scan Size [x] A3 A4 A5 Oficio (Mexico) A6 JIS B4 JIS B5 Book Original Mixed Sizes
Specifies how the text and graphics are oriented on the page
Off Long edge Short edge
Sets the quality of a JPEG photo image in relation to file size and the quality of the image
Best for content 5–90
5–90 Sets the quality of the text in relation to file size and the quality of the image

Understanding printer menus 178
5–90 Sets the quality of a text/photo image in relation to file size and the quality of the image
5–90 Sets the quality of a photo image in relation to file size and the quality of the image
Use Multi‑Page TIFF
Provides a choice between single-page TIFF files and multiple‑page TIFF files. For a multiple-page scan‑to‑FTP job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page of the job.
Specifies whether the transmission log prints
Print log Do not print log Print only for error
Specifies a paper source when printing FTP logs
Tray [x] Manual Feeder
Enables the Text/Photo mode to have smaller file sizes by using 1‑bit images when Color is set to Off
8 bit 1 bit
Base File Name Lets you enter a base file name
Lets you copy a document that contains mixed paper sizes into a single scan job
Specifies whether a preview will appear on the display for scan jobs
Allow Save as Shortcut
Enables shortcut creation for FTP addresses
Adjusts the amount of background visible on a copy
‑4 to 4
Enables an equal balance of colors in the output
Cyan - Red Magenta - Green Yellow - Blue

Understanding printer menus 179
Specifies which color to drop during scanning, and how much to increase or decrease the dropout
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specifies the contrast of the output
0–5 Best for content
Creates a mirror image of the original document
Creates a negative image of the original document
Adjusts the amount of shadow detail visible on a scanned image
‑4 to 4
Scan edge to edge
Specifies whether the original document is scanned edge-to-edge
1–5 Adjusts the amount of sharpness of a scanned image
Enables the user to specify “warm” or “cool” outputs. "Cool” values generate a bluer output than the default while “warm” values generate a redder output than the default.
‑4 to 4

Understanding printer menus 180
Scan Settings
Specifies the format of the file to be sent through FTP
PDF (.pdf) Secure PDF TIFF (.tif) JPEG (.jpg) XPS (.xps)
Sets the version of the PDF file to be sent through FTP
1.2–1.6 A‑1a
Specifies the content of the original document
Text/Photo Photo Text Graphics
Specifies how the original document was produced
Color Laser Inkjet Photo/Film Magazine Newspaper Press Other Black and White Laser
Specifies whether prints are in grayscale or color
Specifies the resolution of the scan in dots per inch (dpi)
150 200 300 400 600 75
1–9 Lightens or darkens the output

Understanding printer menus 181
Specifies the orientation of the scanned image
Specifies the paper size of the document
Letter Legal Executive Tabloid Folio Statement Universal 4 x 6 in. 3 x 5 in. Business Card Custom Scan Size [x] A3 A4 A5 Oficio (Mexico) A6 JIS B4 JIS B5 Book Original Mixed Sizes
Specifies how the text and graphics are oriented on a page
Off Long edge Short edge
Sets the quality of a JPEG photo image in relation to file size and quality
Best for content 5–90
5–90 Sets the quality of the text in relation to file size and the quality of the image
5–90 Sets the quality of a text/photo image in relation to file size and the quality

Understanding printer menus 182
5–90 Sets the quality of a photo image in relation to file size and the quality
Use Multi‑Page TIFF
Provides a choice between single-page TIFF files and multiple‑page TIFF files. For a multiple-page scan to FTP job, either one TIFF file is created containing all the pages, or multiple TIFF files are created with one file for each page.
Enables the Text/Photo mode to have smaller file sizes by using 1‑bit images when Color is set to Off
8 bit 1 bit
File Name Lets you enter a base file name
Lets you copy a document containing mixed paper sizes in a single copy job
Specifies whether a preview appears on the display for scan jobs
Adjusts the amount of background visible on a copy
‑4 to 4
Enables an equal balance of colors in the scanned image
Cyan - Red Magenta - Green Yellow - Blue
Specifies which color to drop during scanning, and how much to increase or decrease the dropout
None Red Green Blue Default Red Threshold
0–255 Default Green Threshold
0–255 Default Blue Threshold
Specifies the contrast of the scanned image
Best for content 0–5

Understanding printer menus 183
Creates a mirror image of the original document
Creates a negative image of the original document
Adjusts the amount of shadow detail visible on a scanned image
‑4 to 4
Scan edge to edge
Specifies whether the original document is scanned edge-to-edge
1–5 Adjusts the amount of sharpness on a scanned image
Enables the user to specify “warm” or “cool” outputs. "Cool” values generate a bluer output than the default while “warm” values generate a redder output than the default.
‑4 to 4
1–999 Specifies a default number of copies for each print job
Sets a default paper source for all print jobs
Tray [x] MP Feeder Manual Paper Manual Envelope
Stacks the pages of a print job in sequence when printing multiple copies
On (1,2,1,2,1,2) Off (1,1,1,2,2,2)
Specifies whether prints are on one side or on both sides of the page
1 sided 2 sided
Specifies whether prints are stapled
Off Auto Back Dual Dual Double Front

Understanding printer menus 184
Specifies whether prints have punched holes
Determines the type of punch finishing performed on prints
2 holes 3 holes 4 holes
Defines the way duplexed pages are bound and how the printing on the back of the page is oriented in relation to the printing on the front of the page
Long Edge Short Edge
Specifies the orientation of a multiple‑page document
Specifies that multiple‑page images be printed on one side of a paper
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Prints a border on each page image
Specifies the positioning of multiple‑page images
Horizontal Reverse Horizontal Reverse Vertical Vertical

Understanding printer menus 185
Specifies whether blank separator sheets are inserted
Off Between Copies Between Jobs Between Pages
Specifies the paper source for separator sheets
Tray [x] Manual Feeder
Specifies whether blank pages are inserted in a print job
Do Not Print Print
Sets the default printer language
PCL Emulation PS Emulation
Specifies that print jobs be removed from the print queue if they require unavailable printer options or custom settings. They are stored in a separate print queue, so other jobs print normally. When the missing information and/or options are obtained, the stored jobs print.

Understanding printer menus 186
Sets the logical and physical printable area
Normal Fit to Page Whole Page
Sets color toner use in printing
Max Yield Max Speed
Sets the storage location for downloads
Specifies how the printer handles temporary downloads, such as fonts and macros stored in RAM, when the printer receives a job that requires more memory than is available
Specifies the order in which held and confidential jobs are printed when Print All is selected
Alphabetical Oldest First Newest First

Understanding printer menus 187
Specifies whether duplex (2‑sided) printing is set as the default for all print jobs
1 sided 2 sided
Defines the way duplexed pages are bound and how the printing on the back of the page is oriented in relation to the printing on the front of the page
Long Edge Short Edge
1–999 Specifies a default number of copies for each print job
Specifies whether blank pages are inserted in a print job
Do Not Print Print
Stacks the pages of a print job in sequence when printing multiple copies
On (1,2,1,2,1,2) Off (1,1,1,2,2,2)
Specifies whether blank separator sheets are inserted
Off Between Copies Between Jobs Between Pages

Understanding printer menus 188
Specifies the paper source for separator sheets
Tray [x] Manual Feeder
Specifies that multiple‑page images be printed on one side of a sheet of paper
Off 2‑Up 3‑Up 4‑Up 6‑Up 9‑Up 12‑Up 16‑Up
Specifies the positioning of multiple‑page images
Horizontal Reverse Horizontal Reverse Vertical Vertical
Specifies the orientation of a multiple‑page sheet
Prints a border on each page image
Adjusts the color output on the printed page
Specifies the printed output resolution
4800 CQ 1200 dpi

Understanding printer menus 189
1–5 Lightens or darkens the printed output
Enables a print mode preferable for files such as architectural drawings, maps, electrical circuit diagrams, and flow charts
Reduces the amount of toner used for graphics and images. The amount of toner used for text is not reduced.
Adjusts brightness in color outputs
‑6 to 6
0–5 Adjusts contrast in color outputs
0–5 Adjusts saturation in color outputs

Understanding printer menus 190
Adjusts color in printed output by increasing or decreasing the amount of toner being used for each color
‑5 to 5 Magenta
‑5 to 5 Yellow
‑5 to 5 Black
‑5 to 5 Reset Defaults 0
Prints sample pages for each of the RGB and CMYK color conversion tables used in the printer
sRGB Display sRGB Vivid Display—True Black Vivid Off—RGB US CMYK Euro CMYK Vivid CMYK Off—CMYK
Customizes the RGB color conversions
Vivid sRGB Display Display True Black sRGB Vivid Off RGB Text
Vivid sRGB Display Display True Black sRGB Vivid Off RGB Graphics
Vivid sRGB Display Display True Black sRGB Vivid Off

Understanding printer menus 191
Customizes the CMYK color conversions
US CMYK Euro CMYK Vivid CMYK Off CMYK Text
US CMYK Euro CMYK Vivid CMYK Off CMYK Graphics
US CMYK Euro CMYK Vivid CMYK Off
Spot Color Replacement Allows users to create and save custom spot colors with corresponding CMYK values
Color Adjust Initiates a recalibration of color conversion tables and allows the printer to make adjustments for color variations in output
Determines if the printer creates a log of the print jobs it receives
Job Accounting Utilities Lets you print and delete log files or export them to a flash drive
Determines how often a log file is created

Understanding printer menus 192
Log Action at End of Frequency
Determines how the printer responds when the frequency threshold expires
None E‑mail Current Log E‑mail & Delete Current Log Post Current Log Post & Delete Current Log
Disk Near Full Level
Specifies the maximum size of the log file before the printer executes the Disk Near Full Action
Disk Near Full Action
Determines how the printer responds when the printer hard disk is nearly full
None E‑mail Current Log E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post Current Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
Determines how the printer responds when disk usage reaches the maximum limit (100MB)
None E‑mail & Delete Current Log E‑mail & Delete Oldest Log Post & Delete Current Log Post & Delete Oldest Log Delete Current Log Delete Oldest Log Delete All Logs Delete All But Current
URL to Post Logs Determines where the printer posts job accounting logs
E‑mail Address to Send Logs Specifies the e‑mail address to which the device sends job accounting logs
Log File Prefix Note: The current host name defined in the TCP/IP menu is used as the default log file prefix.
Menu item Description · 1–99 Off · Disk Full Action

Understanding printer menus 193
Removes confidential and held jobs from the printer hard disk
Confidential Held Not Restored All
Formats the flash memory
Delete Downloads on Disk
Removes downloads from the printer hard disk, including all held jobs, buffered jobs, and parked jobs
Delete Now Do Not Delete
Activate Hex Trace Assists in isolating the source of a print job problem
Provides an estimate of the percentage coverage of toner on a page. The estimate is printed on a separate page at the end of each print job.

Understanding printer menus 194
Prints a page containing information on errors, including XML markup errors
Scales page content to fit the selected page size
Specifies whether to print annotations in the PDF
Do Not Print Print
Prints a page containing the PostScript error
Lock PS Startup Mode
Enables users to disable the SysStart file
Establishes the font search order
Enhances the contrast and sharpness of low‑resolution images and smooths their color transitions

Understanding printer menus 195
Specifies the set of fonts used by the Font Name menu item
Resident Disk Download Flash All
Identifies a specific font and the option where it is stored
Specifies the symbol set for each font name
Changes the point size for scalable typographic fonts
1.00–1008.00
Specifies the font pitch for scalable monospaced fonts
0.08–100

Understanding printer menus 196
Specifies the orientation of text and graphics on the page
Specifies the number of lines that print on each page
Sets the printer to print on A4‑size paper
198 mm 203 mm
Specifies whether the printer automatically performs a carriage return (CR) after a line feed (LF) control command
Auto CR after LF
Specifies whether the printer automatically performs a line feed (LF) after a carriage return (CR) control command
Auto LF after CR
Configures the printer to work with printer software or programs that use different source assignments for trays, drawers, and feeders
Off None 0–199 Assign Tray [x]
Off None 0–199 Assign Manual Paper
Off None 0–199 Assign Manual Env

Understanding printer menus 197
Displays the factory default setting assigned to each tray, drawer, or feeder
Returns all tray, drawer, and feeder assignments to the factory default settings
Joanna MT Letter Gothic Lubalin Graph Marigold MonaLisa Recut Monaco New CenturySbk New York Optima Oxford Palatino StempelGaramond Taffy Times TimesNewRoman Univers Zapf Chancery NewSansMTCS NewSansMTCT New SansMTJA NewSansMTKO
Sets the default font for HTML documents
Albertus MT Antique Olive Apple Chancery Arial MT Avant Garde Bodoni Bookman Chicago Clarendon Cooper Black Copperplate Coronet Courier Eurostile Garamond Geneva Gill Sans Goudy Helvetica Hoefler Text Intl CG Times Intl Courier Intl Univers
1–255 pt Sets the default font size for HTML documents

Understanding printer menus 198
1–400% Scales the default font for HTML documents
Sets the page orientation for HTML documents
8–255 mm Sets the page margin for HTML documents
Specifies whether to print backgrounds on HTML documents
Print Do Not Print
Selects the optimal paper size, scaling, and orientation
Inverts bi‑tonal monochrome images
Scales the image to fit the selected paper size
Best Fit Anchor Center Fit Height/Width Fit Height Fit Width Anchor Top Left
Sets the image orientation
Portrait Landscape Rev Portrait Rev Landscape

Understanding printer menus 199
Controls the printed size of each photo printed from a PictBridge‑enabled device
Auto L 2L Hagaki Postcard Card Size 100 x 150 mm 4 x 6 in 8 x 10 in Letter A4 A5 JIS B5
Determines the maximum number of images that can be printed on one side of paper
Auto Off 2 Up 3 Up 4 Up 6 Up 9 Up 12 Up 16 Up Index Print
Determines which resolution, toner darkness, and color saver values the device uses when printing photos sent from a PictBridge‑enabled device
Identifies the printer default input source when printing photos from a PictBridge‑enabled device
MP Feeder Tray [x] Manual Paper
The Help menu consists of a series of Help pages that are stored in the multifunction printer (MFP) as PDF files. They contain information about using the printer and performing various tasks, including copying, scanning, and faxing.

Understanding printer menus 200
English, French, German, and Spanish translations are stored in the printer.
Other translations are available on the Lexmark Web site at www.lexmark.com.
Print All Guides Prints all the guides
Copy Guide Provides information about making copies and changing settings
Fax Guide Provides information about sending faxes using fax numbers, shortcut numbers, or the address book, and about changing settings
E‑mail Guide Provides information about sending e‑mails using addresses, shortcut numbers, or the address book, and about changing settings
FTP Guide Provides information about scanning documents directly to an FTP server using an FTP address, shortcut numbers, or the address book, and about changing settings
Print Defects Guide Provides help in resolving repeating defects in copies or prints
Information Guide Provides help in locating additional information
Supplies Guide Provides part numbers for ordering supplies
Menu item Description

Securing the printer hard disk and other installed memory 201
Statement of Volatility
Your printer contains various types of memory that are capable of storing device and network settings, information from embedded solutions, and user data. The types of memory—along with the types of data stored by each—are described below.
There are several circumstances under which you might wish to erase the contents of the memory devices installed in your printer. A partial list includes:
In high‑security environments, it may be necessary to take additional steps to ensure that confidential data stored on the printer hard disk cannot be accessed once the printer—or its hard disk—is removed from your premises. While most data can be erased electronically, you may want to consider one or more of the following actions before disposing of a printer or hard disk:

Securing the printer hard disk and other installed memory 202
The volatile memory (RAM) installed on your printer requires a power source to retain information. To erase the buffered data, simply power down the device.
1 Turn off the printer.
2 Hold down 2ABC and 6MNO while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully powered up, the touch screen displays a list of functions, instead of the standard home screen icons.
3 Touch Wipe All Settings.
The printer will reboot several times during this process.
4 Touch Back > Exit Config Menu.
The printer will power‑on reset, and then return to normal operating mode.
Configuring Disk Wiping in the printer menus enables you to remove residual confidential material left by scan, print, copy, and fax jobs, by securely overwriting files that have been marked for deletion.
1 From the Embedded Web Server, click Settings > Security > Disk Wiping.
3 Click Submit.
4 From the Security menu, click Disk Wiping.
5 If you have enabled Manual mode and wish to set up a schedule for disk wiping, click Scheduled Disk Wiping.

Securing the printer hard disk and other installed memory 203
6 Use the Time and Day(s) options to designate when disk wiping should occur, and then click Add. Repeat as needed to schedule additional times for disk wiping. When finished, use the browser Back button to return to the Disk Wiping setup screen.
7 From the Disk Wiping settings screen, select one of the following for each method of disk wiping (Automatic, Manual, and Scheduled):
8 Click Submit.
1 Turn the printer off.
2 Hold down 2ABC and 6MNO while turning the printer on. It takes approximately a minute to boot into the Configuration menu.
Once the printer is fully powered up, the touch screen should display a list of functions, instead of standard home screen icons such as Copy or Fax.
3 Release the buttons when the screen with the progress bar appears. The printer performs a power-on sequence, and then the Configuration menu appears.
5 Touch Yes to proceed with disk wiping. A status bar will indicate the progress of the disk wiping task.
6 Touch Back, and then Exit Config Menu.
The printer will power‑on reset, and then return to normal operating mode.

Securing the printer hard disk and other installed memory 204
Enabling hard disk encryption helps prevent the loss of sensitive data in the event your printer or its hard disk is stolen.
1 From the Embedded Web Server, click Settings > Security > Disk Encryption.
2 From the Disk encryption menu, select Enable.
3 Click Submit.
1 Turn off the printer.
2 Hold down 2ABC and 6MNO while turning the printer on. Release the buttons only when the screen with the progress bar appears.
The printer performs a power-on sequence, and then the Configuration menu appears. Once the printer is fully powered up, the touch screen displays a list of functions, instead of standard home screen icons such as Copy or Fax.
3 Touch Disk Encryption > Enable.
4 Touch Yes to proceed with disk wiping.
A status bar will indicate the progress of the disk wiping task. After the disk has been encrypted, the printer will return to the Enable/Disable screen.
5 Touch Back, and then Exit Config Menu.
The printer will power‑on reset, and then return to normal operating mode.

Maintaining the printer 205
Periodically, certain tasks are required to maintain optimum print quality.
1 Make sure that the printer is turned off and unplugged from the wall outlet.
2 Remove paper from the standard exit bin.
3 Dampen a clean, lint‑free cloth with water.
4 Wipe only the outside of the printer, making sure to include the standard exit bin.
5 Make sure the paper support and standard exit bin are dry before beginning a new print job.
Clean the scanner glass if you encounter print quality problems, such as streaks on copied or scanned images.
1 Slightly dampen a soft, lint-free cloth or paper towel with water.
2 Open the scanner cover.


Maintaining the printer 206
1 White underside ADF cover
2 White underside scanner glass cover
3 Wipe the scanner glass until it is clean and dry.
4 Wipe the white underside of the scanner cover until it is clean and dry.
5 Close the scanner cover.
Choose a cool, clean storage area for the printer supplies. Store supplies right side up in their original packing until you are ready to use them.
Do not expose supplies to:
A message appears on the display when a replacement supply item is needed or when maintenance is required.
From the home screen, touch Status/Supplies > View Supplies.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Device Status.
The Device Status page appears, displaying a summary of supply levels.
3 Scanner glass · 4 ADF glass

Maintaining the printer 207
To order supplies in the U.S., contact Lexmark at 1-800-539-6275 for information about Lexmark authorized supplies dealers in your area. In other countries or regions, visit the Lexmark Web Site at www.lexmark.com or contact the place where you purchased the printer.
When 88.xx [Color] cartridge low appears, order a new toner cartridge.
When 88.xx [Color] cartridge critically low appears, you must replace the specified cartridge.
Part name Lexmark Return Program Regular
Black toner cartridge C540A1KG Not applicable
Cyan toner cartridge C540A1CG Not applicable
Magenta toner cartridge C540A1MG Not applicable
Yellow toner cartridge C540A1YG Not applicable
Black high‑yield toner cartridge C540H1KG C540H2KG
Cyan high‑yield toner cartridge C540H1CG C540H2CG
Magenta high‑yield toner cartridge C540H1MG C540H2MG
Yellow high‑yield toner cartridge C540H1YG C540H2YG
Black extra‑high‑yield toner cartridge C544X1KG
C546U1KG C546U2KG
Cyan extra‑high‑yield toner cartridge C544X1CG C544X2CG
Magenta extra‑high‑yield toner cartridge
Yellow extra‑high‑yield toner cartridge C544X1YG C544X2YG
Part name Part number
Black and color imaging kit C540X74G
Black imaging kit C540X71G
When 82 Replace Waste Toner appears, order a replacement waste toner bottle. The waste toner bottle must be replaced when 82 Replace Waste Toner appears.

Maintaining the printer 208
Part name Part number
Waste toner bottle C540X75G
Replace the waste toner bottle when 82 Replace waste toner appears. The printer will not continue printing until the waste toner bottle is replaced.
1 Unpack the replacement waste toner bottle.
2 Grasp the front door at the side handholds, and then pull it toward you.

3 Open the top door.


Maintaining the printer 209
4 Remove the right side cover.

5 Press the green levers on each side of the waste toner bottle, and then remove it.

6 Place the waste toner bottle in the enclosed packaging.

Maintaining the printer 210
7 Insert the new waste toner bottle.

8 Replace the right side cover.

9 Close the top door.


Maintaining the printer 211
10 Close the front door.

Replace the black and color imaging kit when Replace Color Imaging Kit appears.
1 Grasp the front door at the side handholds, and then pull it toward you to open it.


Maintaining the printer 212
2 Open the top door.

3 Remove the toner cartridges by lifting the handles, and then gently pulling away from the imaging kit.

4 Remove the right side cover.


Maintaining the printer 213
5 Press the green levers on each side of the waste toner bottle, and remove it.

6 Lift the blue levers on the imaging kit, and then pull it toward you.

7 Press down on the blue levers, grasp the green handles on the sides, and then pull the imaging kit out.

Maintaining the printer 214

8 Unpack the replacement black and color imaging kit.
Leave the packaging on the developer units.
9 Gently shake the yellow, cyan, magenta, and black developer units side to side.
10 Remove the red shipping cover from the yellow, cyan, magenta, and black developer units.

11 Insert the yellow, cyan, magenta, and black developer units.

12 Place the used black and color imaging kit in the enclosed package.

Maintaining the printer 215
13 Align and insert the imaging kit.

14 Replace the waste toner bottle.


Maintaining the printer 216
15 Replace the right side cover.

16 Replace the toner cartridges.

17 Close the top door.


Maintaining the printer 217
18 Close the front door.

Replace the specified toner cartridge (yellow, cyan, magenta, or black) when 88.xx [Color] cartridge critically low appears. The printer will not continue printing until the specified cartridge is replaced.
1 Make sure the printer is on and Ready or 88.xx [Color] cartridge critically low appears.
2 Unpack the new cartridge, and set it near the printer.
3 Open the top door.


Maintaining the printer 218
4 Remove the toner cartridge by lifting the handle, and then gently pull away from the imaging kit.

5 Align the new toner cartridge, and then press down until it is all the way into the slot.


Maintaining the printer 219
6 Close the top door.

Replace a developer unit when a print quality defect occurs or when damage occurs to the printer.
1 Grasp the front door at the side handholds, and then pull it toward you to open it.


Maintaining the printer 220
2 Open the top door.

3 Remove the toner cartridges by lifting the handles and then gently pulling away from the imaging kit.

4 Remove the right side cover.


Maintaining the printer 221
5 Press the green levers on each side of the waste toner bottle, and then remove it.

6 Lift the blue levers on the imaging kit, and then pull it toward you.

7 Press down on the blue levers, grasp the handles on the sides, and then pull the imaging kit out.

Maintaining the printer 222

8 Remove the used developer unit.

9 Place the used developer in the enclosed package.
10 Unpack the replacement developer unit.
Leave the packaging on the developer unit.
11 Gently shake the developer unit side to side.
12 Remove the red shipping cover from the developer unit.


Maintaining the printer 223
13 Insert the developer unit.

14 Align and insert the imaging kit.


Maintaining the printer 224
15 Replace the waste toner bottle.

16 Replace the right side cover.

17 Replace the toner cartridges.


Maintaining the printer 225
18 Close the top door.

19 Close the front door.


Maintaining the printer 226
The printer and options can be safely moved to another location by following these precautions:
When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.

Finding advanced networking and administrator information
This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced system support tasks, see the Networking Guide on the Software and Documentation CD and the Embedded Web Server Administrator's Guide on the Lexmark Web site at http://support.lexmark.com.
If the printer is installed on a network, then the Embedded Web Server is available for a range of functions including:
To access the Embedded Web Server for your printer:
1 Type the printer IP address into the address field of your Web browser.
2 Press Enter.
You can view paper tray settings, the level of toner in the toner cartridges, the percentage of life remaining in the maintenance kit, and capacity measurements of certain printer parts from the Device Status page of the Embedded Web Server.
1 Type the printer IP address in the address field of your Web browser.
2 Click Device Status.
1 Open an Embedded Web Server associated with your printer.
Type the printer IP address into the address field of your Web browser.
Administrative support 227

If you do not know the IP address of the printer, you can:
2 Check the virtual display that appears in the top left corner of the screen.
The virtual display works as an actual display would work on a printer control panel, showing printer messages.
You can have the printer send you an e‑mail when the supplies are getting low or when the paper needs to be changed, added, or when there is a paper jam.
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer, you can:
2 Click Settings.
3 Under Other Settings, click E‑mail Alert Setup.
4 Select the items for notification, and type the e‑mail address to receive the alerts.
5 Click Submit.
You can view some reports from the Embedded Web Server. These reports are useful for assessing the status of the printer, the network, and supplies.
To view reports from a network printer:
1 Type the printer IP address into the address field of your Web browser.
If you do not know the IP address of the printer you can:
2 Click Reports, and then click the type of report you want to view.
If you want to retain a list of the current menu settings for reference, then print a menu settings page before restoring the factory default settings.
From the home screen, navigate to:
Administrative support 228

> Settings > General Settings > Factory Defaults > Restore Now > Submit
Administrative support 229

By carefully selecting paper and loading it properly, you can avoid most jams. If jams do occur, follow the steps outlined in this section.
To clear a jam message and resume printing, clear the entire paper path, and then touch Continue. If Jam Recovery is set to On, then the printer prints a new copy of the page that jammed. If Jam Recovery is set to Auto, then the printer reprints the jammed page if enough printer memory is available.

When a jam occurs, a message indicating the jam location appears. The following illustration and table list the paper jams that can occur and the location of each jam. Open doors and covers, and remove trays to access jam locations.
Clearing jams 230


1 200, 241 In the standard 250‑sheet tray and manual feeder (Tray 1)
1 Open the front door. Inspect the area behind the front door, and then remove any jams. 2 Open the fuser cover. Inspect the area under the cover, and then remove any jams. 3 Close the front door. 4 Pull Tray 1 out. Inspect the tray area, and then remove any jams. 5 Verify that the paper is loaded correctly. 6 Reinsert Tray 1.
2 201 Under the fuser
3 202 In the fuser
4 230 In the duplex
5 235 In the duplex
6 242 In the 650‑sheet tray 1 Pull the 650-sheet tray out, and then remove any jams. 2 Reinsert the tray.
7 243 In the 550‑sheet duo tray
1 Pull the 550-sheet tray out, and then remove any jams. 2 Reinsert the tray.
8 250 In the multipurpose feeder
1 Press the latch to the left to release the multipurpose feeder. 2 Inspect the multipurpose feeder, and then remove any jams. 3 Close the multipurpose feeder.
9 290–294 In the ADF Open the ADF cover, and then remove the jam.
Clearing jams 231 · Jam number · Jam location Instructions

1 Grasp the handle, and pull the standard 250-sheet tray (Tray 1) and manual feeder out.

2 Grasp the jammed paper on each side, and then gently pull it out.
3 Insert the tray.
4 From the printer control panel, touch Continue, jam cleared.
1 Grasp the front door at the side handholds, and then pull it toward you to open it.

Clearing jams 232

2 Grasp the jammed paper on each side, and then gently pull it out.

3 Close the front door.
4 From the printer control panel, touch Continue, jam cleared.
1 Grasp the front door at the side handholds, and then pull it toward you to open it.
Clearing jams 233


2 Grasp the green lever, and then pull the fuser cover toward you.

3 Hold the fuser cover down, and then remove the jammed paper.
Clearing jams 234

The fuser cover closes when released.

4 Close the front door.
5 From the printer control panel, touch Continue, jam cleared.
1 Grasp the front door at the side handholds, and then pull it toward you to open it.
2 Grasp the jammed paper, and then gently pull it out.
3 From the printer control panel, touch Continue, jam cleared.
This jam occurs when the paper is too short for the duplex unit.
1 Grasp the front door at the side handholds, and then pull it toward you to open it.
2 Grasp the jammed paper on each side, and then gently pull it out.
3 Load the tray with the correct paper size (A4, letter, legal, or folio).
4 Insert the tray.
5 Close the front door.
6 From the printer control panel, touch Continue, jam cleared.
Clearing jams 235

1 Grasp the handle, and then pull the standard 250-sheet tray (Tray 1).

2 Firmly grasp the jammed paper on each side, and then gently pull it out.
3 Insert the tray.
4 From the printer control panel, touch Continue, jam cleared.
1 Grasp the optional 650-sheet tray handle, and then pull the tray out.

2 Firmly grasp the jammed paper, and then gently pull it out.
3 Insert the tray.
4 From the printer control panel, touch Continue, jam cleared.
Clearing jams 236

1 Grasp the optional 550-sheet tray handle, and then pull the tray out.

2 Firmly grasp the jammed paper, and then gently pull it out.
3 Insert the tray.
4 From the printer control panel, touch Continue, jam cleared.
1 Remove all paper from the multipurpose feeder.
2 Push the lever in the multipurpose feeder to access the jammed paper.

3 Firmly grasp the jammed paper on each side, and then gently pull it out.
4 From the printer control panel, touch Continue, jam cleared.
Clearing jams 237

1 Remove all original documents from the ADF.
2 Open the ADF cover, firmly grasp any jammed paper, and then gently pull it out. Remove the pick arm assembly to remove hard‑to‑reach jammed paper.

3 Close the ADF cover.
4 Open the scanner cover, firmly grasp any jammed paper, and then gently pull it out.

5 Close the scanner cover.
6 From the printer control panel, touch Continue, jam cleared.
Clearing jams 238
![Page 239 of the Lexmark X548 user manual — Change [paper source] to [custom type name] load [orientation]](/cdn/reader/4e/4e361cbfc4ffd5e542d96fb0dd38ca3d4b5c75af269e4915b54558ccd23ba126/images/page-239.webp?w=400)
Solving basic printer problems
If there are basic printer problems, or the printer is unresponsive, make sure:
Once you have checked each of these possibilities, turn the printer off, wait for about 10 seconds, and then turn the printer back on. This often fixes the problem.
Wait for the process to complete.
Try one or more of the following:
Try one or more of the following
Troubleshooting 239
![Page 240 of the Lexmark X548 user manual — Change [paper source] to [paper size] [paper type]](/cdn/reader/4e/4e361cbfc4ffd5e542d96fb0dd38ca3d4b5c75af269e4915b54558ccd23ba126/images/page-240.webp?w=400)
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 240

Try one or more of the following:
1 Turn the printer off, and then on.
2 Open and then fully close the front door of the printer.
Error reading USB drive. Remove drive.
An unsupported USB device has been inserted. Remove the USB device, and then install a supported one.
Error reading USB hub. Remove hub.
An unsupported USB hub has been inserted. Remove the USB hub, and then install a supported one.
Fax Station Name not set up. Contact system administrator.
The Fax Station Name has not been entered. Sending and receiving faxes is disabled until fax is configured properly.
Try one or more of the following:
Fax Station Number not set up. Contact system administrator.
The Fax Station Number has not been entered. Sending and receiving faxes is disabled until fax is configured properly.
Try one or more of the following:
If restarting job, replace originals that have not begun to exit the scanner
Try one or more of the following:
Troubleshooting 241
![Page 242 of the Lexmark X548 user manual — Load [src] with [type] [size]](/cdn/reader/4e/4e361cbfc4ffd5e542d96fb0dd38ca3d4b5c75af269e4915b54558ccd23ba126/images/page-242.webp?w=400)
Fully insert the specified tray into the printer.
Try one or more of the following:
If the printer finds a tray that has the correct paper type and size, it feeds from that tray. If the printer cannot find a tray with the correct paper type and size, it prints from the default paper source. • Cancel the print job.
Try one or more of the following:
If the printer finds a tray that has the correct paper type and size, it feeds from that tray. If the printer cannot find a tray with the correct paper type and size, it prints from the default paper source. • Cancel the print job.
Try one or more of the following:
If the printer finds a tray that has the correct paper type and size, it feeds from that tray. If the printer cannot find a tray with the correct paper type and size, it feeds from the default paper source. • Cancel the print job.
Try one or more of the following:
If the printer finds a tray that has the correct paper type and size, it feeds from that tray. If the printer cannot find a tray with the correct paper type and size, it feeds from the default paper source. • Cancel the print job.
Troubleshooting 242

Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
There is not enough memory to print the fax job.
Touch Continue to clear the message without printing. Held faxes will attempt to print after the printer has been restarted.
The analog phone line was not detected; the fax is disabled. Connect the printer to an analog phone line, and then touch Continue.
Troubleshooting 243

Remove any remaining packaging material from the specified location.
Remove the stack of paper from the standard exit bin.
Replace all originals if restarting job.
Try one or more of the following:
The scanner failed to feed one or more pages through the Automatic Document Feeder (ADF).
1 Remove all pages from the ADF.
2 Flex the pages.
3 Place the pages in the ADF.
4 Adjust the ADF guides.
Try one or more of the following:
Close the ADF cover to clear the message.
The scan job exceeds the maximum number of pages. Touch Cancel job to clear the message and cancel the scan job.
Troubleshooting 244
![Page 245 of the Lexmark X548 user manual — 32.xx Replace unsupported [color] cartridge](/cdn/reader/4e/4e361cbfc4ffd5e542d96fb0dd38ca3d4b5c75af269e4915b54558ccd23ba126/images/page-245.webp?w=400)
Touch Continue to delete the specified job.
The camera mode does not support PictBridge.
Unplug the camera, change the mode and plug the camera back into the printer.
An unsupported disk has been inserted. Remove the unsupported disk, and then install a supported one.
Try one or more of the following:
Try one or more of the following:
The specified toner cartridge is either missing or not functioning properly. Try one or more of the following:
The imaging kit is either missing or not functioning properly. Try one or more of the following:
Remove the unsupported toner or print cartridge, and then install a supported one.
Troubleshooting 245

Try one or more of the following:
Try one or more of the following:
The printer deleted some held jobs in order to process current jobs.
Touch Continue to clear the message.
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Troubleshooting 246

Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
Try one or more of the following:
The printer discards any data received through the USB port. • Make sure the USB Buffer menu item is not set to Disabled.
Troubleshooting 247

Something has changed in the printer to invalidate the held jobs. Possible changes include:
Touch Continue to clear the message.
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Remove the excess flash memory.
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer back on.
1 Turn the printer off.
2 Unplug the power cord from the wall outlet.
3 Remove the additional trays.
4 Connect the power cord to a properly grounded outlet.
5 Turn the printer back on.
Try one or more of the following:
Try one or more of the following:
Troubleshooting 248
![Page 249 of the Lexmark X548 user manual — 88.xx [Color] cartridge critically low](/cdn/reader/4e/4e361cbfc4ffd5e542d96fb0dd38ca3d4b5c75af269e4915b54558ccd23ba126/images/page-249.webp?w=400)
Try one or more of the following:
Try one or more of the following:
If the error message remains, the hard disk may be defective and require replacing.
The printer needs to be serviced. For more information, contact customer support.
1 Replace the waste toner bottle.
For instructions on replacing the waste toner bottle, from the printer control panel touch More Information.
2 Touch Continue to clear the message and continue printing.
Reinsert the waste toner bottle into the printer.
Order a replacement waste toner bottle immediately.
1 Replace the waste toner bottle.
For instructions on installing the waste toner bottle, from the printer control panel touch More Information.
2 Touch Continue to clear the message and continue printing.
Replace the specified toner cartridge.
1 Touch More Information from the printer control panel for instructions on replacing a print cartridge.
2 Touch Continue to clear the message and continue printing.
Troubleshooting 249

1 Order a replacement toner cartridge immediately.
2 Remove the specified cartridge.
3 Firmly shake the cartridge side‑to‑side and front‑to‑back several times to redistribute the toner.
4 Reinsert the cartridge, and then touch Continue to clear the message and continue printing.
1 Order a replacement toner cartridge.
2 Remove the specified cartridge.
3 Firmly shake the cartridge side‑to‑side and front‑to‑back several times to redistribute the toner.
4 Reinsert the cartridge, and then touch Continue to clear the message and continue printing.
Print without the scanner or contact your system support person.
840.02 Scanner disabled. Contact system administrator if problem persists.
The printer identified a problem with the scanner and automatically disabled it. Try one or more of the following:
1 Remove all pages from the ADF.
2 Turn the printer off.
3 Wait for 15 seconds, and then turn the printer on.
4 Place the document in the ADF, and then adjust the paper guides.
5 From the home screen, touch Copy, or use the keypad to enter the number of copies.
6 Change the copy settings as needed.
7 Touch Copy It.
The scanner failed to feed one or more pages through the ADF.
1 Remove all original documents from the ADF.
2 Do not fold or crease original documents. Straighten the edges on a level surface.
Troubleshooting 250

3 Load the original documents in the ADF.
4 Adjust the ADF guides.
5 Touch Continue, jam cleared.
The PDF files may contain unavailable fonts.
1 Open the document you want to print in Adobe Acrobat.
2 Click the printer icon > Advanced > Print as image > OK > OK.
The printer self test failed. Turn the printer off, wait about 10 seconds, and then turn the printer back on.
If Performing Self Test and Ready do not appear, turn the printer off and contact Customer Support.
Make sure the flash drive is supported.
Try one or more of the following:
From the printer control panel, check the status. If necessary, follow the recovery instructions.
Make sure Ready appears on the display before sending a print job.
Remove and then reinstall or replace the supply.
Remove the paper stack from the standard exit bin.
Load paper in the tray.
Troubleshooting 251

The printer software is available on the Lexmark Web site at http://support.lexmark.com.
MAKE SURE YOU ARE USING A RECOMMENDED USB, SERIAL, OR ETHERNET CABLE
For more information, visit the Lexmark Web site at http://support.lexmark.com.
Check the cable connections to the printer and print server to make sure they are secure.
For more information, see the setup documentation that came with the printer.
These are possible solutions. Try one or more of the following:
The print job may contain a formatting error or invalid data.
If you are printing from the Internet, then the printer may be reading multiple job titles as duplicates and deleting all jobs except the first one.
Free up additional printer memory by scrolling through the list of held jobs and deleting some of them.
Troubleshooting 252

Try one or more of the following:
Eliminate the number and size of fonts, the number and complexity of images, and the number of pages in the print job.
From the home screen, navigate to:
> Settings > General Settings > Print Recovery > Page Protect > Off >
When using Eco‑Mode or Quiet Mode settings, you may notice a reduction in performance.
C HECK THE PAPER TYPE AND PAPER SIZE SETTINGS
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the paper type and paper size settings.
These are possible solutions. Try one or more of the following:
Troubleshooting 253

USE THE SAME PAPER SIZE AND PAPER TYPE SETTINGS
These are possible solutions. Try one or more of the following:
From the printer control panel Finishing menu, Print Properties, or the Print dialog, set Collate to On.
Reduce the complexity of the print job by eliminating the number and size of fonts, the number and complexity of images, and the number of pages in the job.
Add printer memory.
I NCREASE THE P RINT T IMEOUT VALUE
1 From the home screen, navigate to:
> Settings > General Settings > Timeouts
2 Touch the left or right arrow next to Print Timeout until the desired value appears.
3 Touch Submit.
These are possible solutions. Try one or more of the following:
Clear any error messages.
Make sure the printer is plugged in, the power is on, and Ready appears.
Troubleshooting 254

Make sure there are no obstructions:
1 Lift the scanner unit.
2 Remove any obstruction keeping the scanner unit open.
3 Lower the scanner unit.
These are some examples of poor copy quality:
Try one or more of the following:
Check the display and clear any error messages.
When the print remains faded, replace the toner or print cartridge.
The scanner glass may be dirty. Clean the scanner glass with a clean, lint‑free cloth dampened with water.
For more information, see “Cleaning the scanner glass” on page 205.
Adjust the toner darkness from the Copy menus.
Check the quality of the original document.
Troubleshooting 255

Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
When patterns (moiré) appear in the output:
Advanced Options > Advanced Imaging > Sharpness > lower the Sharpness setting • On the Copy screen, make sure no scaling is being selected.
When the text is light or disappearing:
Content > Text >
> select the appropriate source for the original document being copied >
Advanced Options > Advanced Imaging > Sharpness > increase the current setting • From the Copy screen, navigate to:
Advanced Options > Advanced Imaging > Background removal, and then reduce the current setting • From the Copy screen, navigate to:
Advanced Options > Advanced Imaging > Contrast > increase the current setting • From the Copy screen, navigate to:
Advanced Options > Advanced Imaging > Shadow detail > reduce the current setting
When the output appears washed out or overexposed:
Advanced Options > Advanced Imaging > Shadow detail > reduce the current setting • From the Copy screen, navigate to:
Advanced Options > Advanced Imaging > Background removal > reduce the current setting
These are possible solutions. Try one or more of the following:
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Troubleshooting 256

Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Size setting from the Paper menu.
If your scanner is not responding, then make sure:
Once you have checked each of these possibilities, turn the printer off and then back on. This often fixes the problem with the scanner.
These are possible solutions. Try one or more of the following:
Make sure the network or USB cable is securely connected to the computer and the printer.
Turn off and then restart the computer.
These are possible solutions. Try one or more of the following:
Close all programs not being used.
Troubleshooting 257

Select a lower scan resolution.
These are possible solutions. Try one or more of the following:
Clear any error messages.
Clean the scanner glass with a clean, lint‑free cloth dampened with water. For more information, see “Cleaning the scanner glass” on page 205.
Increase the resolution of the scan for a higher quality output.
Make sure the quality of the original document is satisfactory.
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
These are possible solutions. Try one or more of the following:
Make sure the document or photo is loaded facedown on the scanner glass in the upper left corner.
Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Size setting from the Paper menu.
Troubleshooting 258

These are possible solutions. Try one or more of the following:
Clear any error messages.
Make sure the printer is plugged in, the power is on, and Ready appears.
Make sure the network or USB cable is securely connected to the computer and the printer.
The indicator light blinks red until you set up fax and e‑mail. To set up fax and e‑mail, follow these steps:
1 From the home screen, navigate to:
> General Settings > Run initial setup > Yes > Submit
2 Turn the printer off, and then turn it back on.
3 From the printer control panel, touch your language.
4 Touch your country or region, and then touch Continue.
5 Select your time zone, and then touch Continue.
6 Touch Fax and E‑mail to clear the icons, and then touch Continue.
Contact your telecommunications company to verify that your telephone line is subscribed to the caller ID service.
If your region supports multiple caller ID patterns, you may have to change the default setting. There are two settings available: FSK (pattern 1) and DTMF (pattern 2). The availability of these settings by way of the Fax menu depends on whether your country or region supports multiple caller ID patterns. Contact your telecommunications company to determine which pattern or switch setting to use.
Troubleshooting 259

These are possible solutions. Try one or more of the following:
Clear any error messages.
Make sure the printer is plugged in, the power is on, and Ready appears.
Make sure the cable connections for the following hardware are secure, if applicable:
1 Plug a telephone into the wall jack.
2 Listen for a dial tone.
3 If you do not hear a dial tone, then plug a different telephone into the wall jack.
4 If you still do not hear a dial tone, then plug a telephone into a different wall jack.
5 If you hear a dial tone, then connect the printer to that wall jack.
The fax modem is an analog device. Certain devices can be connected to the printer so that digital telephone services can be used.
Troubleshooting 260

To ensure the printer is working correctly, connect it directly to the telephone line. Disconnect any answering machines, computers with modems, or telephone line splitters.
Clear any jams, and then make sure that Ready appears.
Call Waiting can disrupt fax transmissions. Disable this feature before sending or receiving a fax. Call your telephone company to obtain the keypad sequence for temporarily disabling Call Waiting.
Voice Mail offered through your local telephone company may disrupt fax transmissions. To enable both Voice Mail and the printer to answer calls, you may want to consider adding a second telephone line for the printer.
1 Dial the fax number.
2 Scan the original document one page at a time.
Try one or more of the following:
If the tray is empty, then load paper in the tray or feeder.
The ring count delay sets the number of times the phone rings before the printer answers. If you have extension phones on the same line as the printer, or subscribe to the telephone company's Distinctive Ring service, then keep the Ring Delay setting at 4.
1 Type the printer IP address in the address field of your Web browser.
If you do not know the IP address of the printer, then you can:
2 Click Settings > Fax Settings > Analog Fax Setup.
3 In the Rings to Answer field, enter the number of times you want the phone to ring before the printer answers.
4 Click Submit.
Troubleshooting 261

Replace the toner or print cartridge.
These are possible solutions. Try one or more of the following:
From the printer control panel, press the Fax button to put the printer in Fax mode.
Load the original document faceup, short edge first into the ADF or facedown on the scanner glass in the upper left corner.
Try one or more of the following:
Ask the person who sent you the fax to:
When 88 Cartridge low appears or when the prints appear faded, replace the cartridge.
Decrease the incoming fax transmission speed:
1 Type the printer IP address in the address field of your Web browser.
2 Click Settings > Fax Settings > Analog Fax Setup.
Troubleshooting 262

3 In the Max Speed box, click one of the following: 2400 4800 9600 14400 33600
4 Click Submit.
C HECK THE SYSTEM LOG FOR RELEVANT DETAILS
1 Type the printer IP address or host name in the address field of your Web browser.
If you do not know the IP address or host name of the printer, then you can:
2 Click Settings or Configuration.
3 Click Device Solutions > Solutions (eSF) > System tab > Log.
4 From the Filter menu, select an application status.
5 From the Application menu, select an application, and then click Submit.
MAKE SURE THE FILE NAME YOU WANT TO SCAN TO IS NOT ALREADY IN USE
Verify that the file to which you want to scan is not open by another application or user.
To help prevent errors, make sure either “Append time stamp” or “Overwrite existing file” is selected in the destination configuration settings.
In the destination configuration settings, lower the scan settings. For example, lower the scan resolution, disable Color, or change the Content type to Text.
If you still cannot isolate the problem, then contact customer support.
Troubleshooting 263

Try one or more of the following:
Turn the printer off, wait for about 10 seconds, and then turn the printer on.
1 Turn the printer off using the power switch.
2 Unplug the power cord from the wall outlet, and then from the printer.
3 Check the connection between the option and the printer.
Print a menu settings page and check to see if the option is listed in the Installed Options list. If the option is not listed, then reinstall it. For more information, see the hardware setup documentation that came with the option, or go to www.lexmark.com to view the option instruction sheet.
From the computer you are printing from, select the option.
For more information, see “Updating available options in the printer driver” on page 39.
M AKE SURE THE PAPER IS LOADED CORRECTLY
1 Open the paper tray.
2 Check for paper jams or misfeeds.
3 Make sure paper guides are aligned against the edges of the paper.
4 Make sure the paper tray closes properly.
5 Close the door.
Turn the printer off. Wait 10 seconds. Turn the printer back on.
Troubleshooting 264

C HECK THE MULTIPURPOSE FEEDER
Make sure the 650‑sheet duo drawer (multipurpose feeder) is installed properly.
Clear any jams in the multipurpose feeder.
Make sure:
Use recommended paper and specialty media. For more information, see the chapter about paper and specialty media guidelines.
Move the guides in the tray to the correct position for the size loaded.
If a service message appears, turn the printer off, wait about 10 seconds, and then turn the printer back on. If the error recurs, call for service.
Make sure the memory card is securely connected to the printer system board.
These are possible solutions. Try one or more of the following:
Use recommended paper and specialty media. For more information, see the chapter about paper and specialty media guidelines.
Troubleshooting 265

MAKE SURE THERE IS NOT TOO MUCH PAPER IN THE PAPER TRAY
Make sure the stack of paper you load does not exceed the maximum stack height indicated in the tray or on the multipurpose feeder.
Move the guides in the tray to the correct positions for the paper size loaded.
C HECK THE PAPER PATH
The paper path is not clear. Clear jammed paper from the entire paper path, and then touch Continue.
T URN ON J AM R ECOVERY
1 From the home screen, navigate to:
> Settings > General Settings > Print Recovery
2 Touch the arrows next to Jam Recovery until On or Auto appears.
3 Touch Submit.
Troubleshooting 266

The information in the following topics may help you solve print quality problems. If these suggestions still do not correct the problem, contact Customer Support. You may have a printer part that requires adjustment or replacement.
Try one or more of the following:
MAKE SURE THERE IS NO PACKING MATERIAL LEFT ON THE TONER OR PRINT CARTRIDGE
Remove the cartridge and make sure the packing material is properly removed. Reinstall the cartridge.
MAKE SURE THE TONER OR PRINT CARTRIDGE IS NOT LOW ON TONER
When 88.xx [color] cartridge low appears, make sure that toner is distributed evenly among all four cartridges:
1 Remove the cartridge.
2 Firmly shake the cartridge side-to-side and front-to-back several times to redistribute the toner.
3 Reinsert the cartridge.
If the problem continues, then the printer may need to be serviced. For more information, contact customer support.
If you are using downloaded fonts, verify that the fonts are supported by the printer, the host computer, and the software program.
Troubleshooting 267

Try one or more of the following:
Move the width and length guides in the tray to the correct positions for the paper size loaded.
Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Size setting.
ABCDE
ABCDE ABCDE
M AKE SURE THE IMAGING KIT IS NOT WORN OR DEFECTIVE
When 31.xx Defective imaging kit appears, replace the imaging kit.
ABCDE
ABCDE ABCDE
C HECK THE T ONER D ARKNESS SETTING
Select a lighter Toner Darkness setting:
Troubleshooting 268

ABCD ABCD ABCD
These are possible solutions. Try one or more of the following:
Move the guides in the tray to the correct positions for the paper size loaded.
Make sure the paper size setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Size setting.
T HE IMAGING KIT MAY BE DEFECTIVE
Replace the imaging kit.
If the problem continues, the printer may need to be serviced. For more information, contact Customer Support.
Troubleshooting 269

Try one or more of the following:
Make sure the paper type and weight settings match the paper loaded in the tray or feeder:
1 From the printer control panel Paper menu, check the Paper Type and Paper Weight settings.
Paper absorbs moisture due to high humidity. Store paper in its original wrapper until you use it.
These are possible solutions. Try one or more of the following:
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel Paper menu, check the Paper Type setting.
Avoid textured paper with rough finishes.
Troubleshooting 270

Replace the fuser.
R EPLACE THE DEVELOPER UNIT
Replace the developer unit if the defects occur in every 43.9 mm (1.7 in.) of the page.
Replace the imaging kit if print defects occur in the following instances:
C HECK THE PAPER GUIDES
Move the guides in the tray to the correct positions for the paper size loaded.
Make sure you are using paper that meets the printer specifications.

Try one or more of the following:
The Toner Darkness setting may be too light, the Brightness setting may be too light, or the Contrast setting may be too low.
The paper may have absorbed moisture from high humidity. Store paper in its original wrapper until you use it.
C HECK THE P APER T YPE SETTING
Make sure the Paper Type setting matches the paper loaded in the tray or feeder:
When 88.xx [color] cartridge low appears, make sure the toner is distributed evenly within the print cartridge.
1 Remove the toner cartridge.
2 Firmly shake the cartridge side-to-side and front-to-back several times to redistribute the toner.
3 Reinsert the toner cartridge.
If the problem continues, the printer may need to be serviced. For more information, contact customer support.
Troubleshooting 272

Replace the defective toner cartridge.
Try one or more of the following:
The Toner Darkness setting may be too dark, the Brightness setting may be too dark, or the Contrast setting may be too high.
The paper may have absorbed moisture due to high humidity. Store paper in its original wrapper until you use it.
C HECK THE P APER T YPE SETTING
Make sure the Paper Type setting matches the paper loaded in the tray or feeder:
Replace the defective toner cartridge.
Troubleshooting 273

MAKE SURE THE TONER OR PRINT CARTRIDGES ARE INSTALLED CORRECTLY, ARE NOT DEFECTIVE AND NOT LOW
Try one or more of the following:
Replace the imaging kits.
Clean any visible toner from the paper path. If the problem persists, then contact customer support.
Troubleshooting 274

These are possible solutions. Try one or more of the following:
Make sure the paper type setting matches the paper loaded in the tray:
1 From the printer control panel, check the Paper Type setting from the Paper menu.
From the printer control panel Paper menu, make sure the Paper Texture setting matches the paper loaded in the tray.
These are possible solutions. Try one or more of the following:
Replace the imaging kit.
If the problem continues, the printer may need to be serviced. For more information, contact Customer Support.
Contact Customer Support.
Troubleshooting 275

Try one or more of the following:
Use only transparencies that meet the printer specifications.
Make sure the paper type setting is set to Transparency:
1 From the printer control panel Paper menu, check the Paper Type setting.
ABCDE ABCDE ABCDE
Replace the black and color imaging kit.
This section helps answer some basic color‑related questions and describes how some of the features provided in the Quality menu can be used to solve typical color problems.
What is RGB color?
Red, green, and blue light can be added together in various amounts to produce a large range of colors observed in nature. For example, red and green can be combined to create yellow. Televisions and computer monitors create colors in this manner. RGB color is a method of describing colors by indicating the amount of red, green, or blue needed to produce a certain color.
What is CMYK color?
Cyan, magenta, yellow, and black inks or toners can be printed in various amounts to produce a large range of colors observed in nature. For example, cyan and yellow can be combined to create green. Printing presses, inkjet printers, and color laser printers create colors in this manner. CMYK color is a method of describing colors by indicating the amount of cyan, magenta, yellow, and black needed to reproduce a particular color.
Troubleshooting 276

How is color specified in a document to be printed?
Software programs typically specify document color using RGB or CMYK color combinations. Additionally, they allow users to modify the color of each object in a document. For more information, see the software program Help topics.
How does the printer know what color to print?
When a user prints a document, information describing the type and color of each object is sent to the printer. The color information is passed through color conversion tables that translate the color into the appropriate amounts of cyan, magenta, yellow, and black toner needed to produce the desired color. The object information determines the application of color conversion tables. For example, it is possible to apply one type of color conversion table to text while applying a different color conversion table to photographic images.
Why doesn't the printed color match the color I see on the computer screen?
The color conversion tables used in Auto Color Correction mode generally approximate the colors of a standard computer monitor. However, because of technology differences that exist between printers and monitors, there are many colors that can also be affected by monitor variations and lighting conditions. For recommendations on how the printer color sample pages may be useful in solving certain color‑matching problems, see the question, “How can I match a particular color (such as a corporate logo)?”
The printed page appears tinted. Can I adjust the color?
Sometimes a printed page may appear tinted (for example, everything printed seems to be too red). This can be caused by environmental conditions, paper type, lighting conditions, or user preference. In these instances, adjust the Color Balance setting to create a more preferable color. Color Balance provides the user with the ability to make subtle adjustments to the amount of toner being used in each color plane. Selecting positive or negative values for cyan, magenta, yellow, and black (from the Color Balance menu) will slightly increase or decrease the amount of toner used for the chosen color. For example, if a printed page has a red tint, then decreasing both magenta and yellow could potentially improve the color balance.
My color transparencies seem dark when they are projected. Is there anything I can do to improve the color?
This problem most commonly occurs when projecting transparencies with reflective overhead projectors. To obtain the highest projected color quality, transmissive overhead projectors are recommended. If a reflective projector must be used, then adjusting the Toner Darkness setting to 1, 2, or 3 will lighten the transparency. Make sure to print on the recommended type of color transparencies.
What is manual color correction?
When manual color correction is enabled, the printer employs user‑selected color conversion tables to process objects. However, Color Correction must be set to Manual, or no user‑defined color conversion will be implemented. Manual color correction settings are specific to the type of object being printed (text, graphics, or images), and how the color of the object is specified in the software program (RGB or CMYK combinations).
To manually apply a different color conversion table:
1 From the Quality menu, select Color Correction, and then select Manual.
2 From the Quality menu, select Manual Color, and then select the appropriate color conversion table for the affected object type.
Troubleshooting 277

Object type Color conversion tables
How can I match a particular color (such as a corporate logo)?
From the printer Quality menu, nine types of Color Samples sets are available. These are also available from the Color Samples page of the Embedded Web Server. Selecting any sample set generates a multiple‑page printout consisting of hundreds of colored boxes. Either a CMYK or RGB combination is located on each box, depending on the table selected. The observed color of each box is obtained by passing the CMYK or RGB combination labeled on the box through the selected color conversion table.
By examining Color Samples sets, a user can identify the box whose color is the closest to the desired color. The color combination labeled on the box can then be used for modifying the color of the object in a software program. For more information, see the software program Help topics. Manual color correction may be necessary to utilize the selected color conversion table for the particular object.
Selecting which Color Samples set to use for a particular color‑matching problem depends on the Color Correction setting being used (Auto, Off, or Manual), the type of object being printed (text, graphics, or images), and how the color of the object is specified in the software program (RGB or CMYK combinations). When the printer Color Correction setting is set to Off, the color is based on the print job information; and no color conversion is implemented.
Note: The Color Samples pages are not useful if the software program does not specify colors with RGB or CMYK combinations. Additionally, certain situations exist in which the software program or the computer operating system adjusts the RGB or CMYK combinations specified in the program through color management. The resulting printed color may not be an exact match of the Color Samples pages.
What are detailed Color Samples and how do I access them?
Detailed Color Samples sets are available only through the Embedded Web Server of a network printer. A detailed Color Samples set contains a range of shades (displayed as colored boxes) that are similar to a user‑defined RGB or CMYK value. The likeness of the colors in the set are dependent on the value entered in the RGB or CMYK Increment box.

To access a detailed Color Samples set from the Embedded Web Server:
1 Type the printer IP address or host name in the address field of your Web browser.
2 Click Configuration > Color Samples > Detailed Options.
3 Select a color conversion table.
4 Enter the RGB or CMYK color number.
5 Enter an increment value from 1–255.
6 Click Print.
Try one or more of the following:
Make sure the printer and computer are turned on and connected to the same network.
Proxy servers may block or restrict you from accessing certain Web sites including the Embedded Web Server. For more information, contact your system support person.
When you call customer support, describe the problem you are experiencing, the message on the display, and the troubleshooting steps you have already taken to find a solution.
You need to know your printer model type and serial number. For more information, see the label on the inside top front cover of the printer. The serial number is also listed on the menu settings page.
In the U.S. or Canada, call 1‑800‑539‑6275. For other countries or regions, visit the Lexmark Web site at http://support.lexmark.com.
Troubleshooting 279

Product name:
Machine type:
Model(s):
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user’s responsibility.
For Lexmark technical support, visit http://support.lexmark.com.
For information on supplies and downloads, visit www.lexmark.com.
© 2012 Lexmark International, Inc.
All rights reserved.
The Software Program and any related documentation are "Commercial Items," as that term is defined in 48 C.F.R. 2.101, "Computer Software" and "Commercial Computer Software Documentation," as such terms are used in 48 C.F.R. 12.212 or 48 C.F.R. 227.7202, as applicable. Consistent with 48 C.F.R. 12.212 or 48 C.F.R. 227.7202-1 through 227.7207-4, as applicable, the Commercial Computer Software and Commercial Software Documentation are licensed to the U.S. Government end users (a) only as Commercial Items and (b) with only those rights as are granted to all other end users pursuant to the terms and conditions herein.
Lexmark X548, X548de · 630, 632, 636 · November 2012

Lexmark, Lexmark with diamond design, and MarkVision are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
ScanBack is a trademark of Lexmark International, Inc.
Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions corresponding to the commands.
The following terms are trademarks or registered trademarks of these companies:

CG Times Based on Times New Roman under license from The Monotype Corporation plc, is a product of Agfa Corporation

Univers Linotype-Hell AG and/or its subsidiaries
All other trademarks are the property of their respective owners.
AirPrint and the AirPrint logo are trademarks of Apple, Inc.
This product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
The manufacturer is not responsible for any radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment.
This product may contain the following modular component(s):
Lexmark Regulatory Type/Model LEX-M04-001, FCC ID: IYLLEXM04001; IC:2376A-M04001
All licensing notices associated with this product can be viewed from the root directory of the installation software CD.
The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
1-meter average sound pressure, dBA
Values are subject to change. See www.lexmark.com for current values.
Printing 48 dBA · Ready 32 dBA

The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products.
If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.
Do not dispose of the printer or supplies in the same manner as normal household waste. Consult your local authorities for disposal and recycling options.
This product contains Perchlorate material. Special handling may apply. For more information, go to http://www.dtsc.ca.gov/hazardouswaste/perchlorate/.
This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the metal frame of the printer.

Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to comply with Environmental Protection Agency (EPA) ENERGY STAR requirements as configured when shipped by Lexmark.
Ambient temperature 15.6°C – 32.2°C
Shipping and storage temperature ‑40.0°C – 60.0°C
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, Chapter I, Subchapter J for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The printer contains internally a Class IIIb (3b) laser that is nominally a 7 milliwatt gallium arsenide laser operating in the wavelength of 655-675 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition.
A laser notice label may be affixed to this printer as shown:
Opasnost - Nevidljivo lasersko zračenje kada su kasete uklonjene i poništena sigurnosna veza. Izbjegavati izlaganje zracima.
NEBEZPEČÍ - Když jsou vyjmuty kazety a je odblokována pojistka, ze zařízení je vysíláno neviditelné laserové záření. Nevystavujte se působení laserového paprsku. FARE - Usynlig laserstråling, når patroner fjernes, og spærreanordningen er slået fra. Undgå at blive udsat for laserstrålen.
VAARA - Näkymätöntä lasersäteilyä on varottava, kun värikasetit on poistettu ja lukitus on auki. Vältä lasersäteelle altistumista. GEFAHR - Unsichtbare Laserstrahlung beim Herausnehmen von Druckkassetten und offener Sicherheitssperre. Laserstrahl meiden.
ΚΙΝΔΥΝΟΣ - Έκλυση αόρατης ακτινοβολίας laser κατά την αφαίρεση των κασετών και την απασφάλιση της μανδάλωσης. Αποφεύγετε την έκθεση στην ακτινοβολία laser.
VESZÉLY – Nem látható lézersugárzás fordulhat elő a patronok eltávolításakor és a zárószerkezet felbontásakor. Kerülje a lézersugárnak való kitettséget.
ОПАСНО! Невидимое лазерное излучение при извлеченных картриджах и снятии блокировки. Избегайте воздействия лазерных лучей.
Pozor – Nebezpečenstvo neviditeľného laserového žiarenia pri odobratých kazetách a odblokovanej poistke. Nevystavujte sa lúčom.
危险 - 当移除碳粉盒及互锁失效时会产生看不见的激光辐射,请避免暴露在激光光束下。
危険 - カートリッジが取り外され、内部ロックが無効になると、見えないレーザー光が放射されます。 このレーザー光に当たらないようにしてください。

The following table documents the power consumption characteristics of the product.
Mode Description Power consumption (Watts)
Printing The product is generating hard‑copy output from electronic inputs. 540 W
Copy The product is generating hard‑copy output from hard‑copy original documents.
Scan The product is scanning hard‑copy documents. 60 W
Ready The product is waiting for a print job. 50 W
Sleep Mode The product is in a high‑level energy‑saving mode. 23 W
Off The product is plugged into a wall outlet, but the power switch is turned off. 0.2 W
The power consumption levels listed in the previous table represent time-averaged measurements. Instantaneous power draws may be substantially higher than the average.
Values are subject to change. See www.lexmark.com for current values.
This product is designed with an energy-saving mode called Sleep Mode. The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this product is not used for a specified period of time, called the Sleep Mode Timeout.
Factory default Sleep Mode Timeout for this product (in minutes): 30 minutes
By using the configuration menus, the Sleep Mode Timeout can be modified between 1 minute and 240 minutes. Setting the Sleep Mode Timeout to a low value reduces energy consumption, but may increase the response time of the product. Setting the Sleep Mode Timeout to a high value maintains a fast response, but uses more energy.
If this product has an off mode which still consumes a small amount of power, then to completely stop product power consumption, disconnect the power supply cord from the electrical outlet.
It is sometimes helpful to calculate the total product energy usage. Since power consumption claims are provided in power units of Watts, the power consumption should be multiplied by the time the product spends in each mode in order to calculate energy usage. The total product energy usage is the sum of each mode's energy usage.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003.
Cet appareil numérique de classe A est conforme aux exigences de la norme canadienne relative aux équipements pouvant causer des interférences NMB-003.
This product is in conformity with the protection requirements of EC Council directives 2004/108/EC and 2006/95/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class A limits of EN 55022 and safety requirements of EN 60950.
This is a product that complies with the emission requirements of EN55022 Class A limits and immunity requirements of EN55024. This product is not intended to be used in residential/domestic environments.
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
This section contains regulatory information pertaining to products that contain telecommunication terminal equipment such as facsimile.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachments (ACTA). On the back of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to your telephone company.
This equipment uses the RJ-11C Universal Service Order Code (USOC) jack.
A plug and jack used to connect this equipment to the premises’ wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is

provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See your setup documentation for more information.
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact your local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (for example, 03 is a REN of 0.3). For earlier products, the REN is shown separately on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. You will also be advised of your right to file a complaint with the FCC.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
If you experience trouble with this equipment, for repair or warranty information, contact Lexmark International, Inc. at www.lexmark.com or your Lexmark representative. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
This equipment contains no user serviceable parts. For repair and warranty information, contact Lexmark International, Inc. See the previous paragraph for contact information.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter's Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless said message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message, and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)
See your user documentation in order to program this information into your fax machine.
This product meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number (REN) is an indication of the maximum number of terminals allowed to be connected to a telephone interface. The terminus of an interface may consist of any combination of devices, subject only to the requirement that the sum of the RENs of all the devices does not exceed five. The modem REN is located on the rear of the equipment on the product labeling.

Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources. This has been identified as a major nationwide problem. It is recommended that the customer install an appropriate AC surge arrestor in the AC outlet to which this device is connected. An appropriate AC surge arrestor is defined as one that is suitably rated, and certified by UL (Underwriter’s Laboratories), another NRTL (Nationally Recognized Testing Laboratory), or a recognized safety certification body in the country/region of use. This is to avoid damage to the equipment caused by local lightning strikes and other electrical surges.
This equipment uses CA11A telephone jacks.
Ce produit est conforme aux spécifications techniques d’Industrie Canada. Le numéro REN (ringer equivalence number : numéro d’équivalence de sonnerie) fournit une indication du nombre maximum de terminaux pouvant être connectés à l’interface téléphonique. En bout de ligne, le nombre d’appareils qui peuvent être connectés n’est pas directement limité, mais la somme des REN de ces appareils ne doit pas dépasser cinq. Le numéro REN du modem est indiqué sur l’étiquette produit située à l’arrière de l’équipement.
Les compagnies de téléphone constatent que les surtensions électriques, en particulier celles dues à la foudre, entraînent d'importants dégâts sur les terminaux privés connectés à des sources d’alimentation CA. Il s’agit-là d’un problème majeur d’échelle nationale. En conséquence, il vous est recommandé de brancher un parasurtenseur dans la prise de courant à laquelle l’équipement est connecté. Utilisez un parasurtenseur répondant à des caractéristiques nominales satisfaisantes et certifié par le laboratoire d’assureurs UL (Underwriter’s Laboratories), un autre laboratoire agréé de type NRTL (Nationally Recognized Testing Laboratory) ou un organisme de certification agréé dans votre région ou pays. Ceci prévient tout endommagement de l’équipement causé par les orages et autres surtensions électriques.
Cet équipement utilise des prises de téléphone CA11A.
The following are special conditions for the Facsimile User Instructions. The grant of a telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.
This equipment shall not be set up to make automatic calls to the Telecom's 111 Emergency Service.
This equipment may not provide for the effective hand-over of a call to another device connected to the same line.
This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom customers.
Some parameters required for compliance with Telecom's telepermit requirements are dependent on the equipment associated with this device. The associated equipment shall be set to operate within the following limits for compliance to Telecom's specifications:

This product requires a Swiss billing tone filter (Lexmark part number 80D1877) to be installed on any line which receives metering pulses in Switzerland. The filter must be used, as metering pulses are present on all analog telephone lines in Switzerland.
Cet appareil nécessite l’utilisation d’un filtre de tonalité de facturation suisse (nº de référence Lexmark : 80D1877) devant être installé sur toute ligne recevant des impulsions de comptage en Suisse. Ce filtre doit être utilisé pour toute installation car ces impulsions existent sur toutes les lignes téléphoniques suisses.
Für dieses Produkt muss ein schweizerischer Billing Tone Filter zur Zählzeichenübertragung (Lexmark Teilenummer 80D1877) für jede Leitung installiert werden, über die in der Schweiz Zeitsteuertakte übertragen werden. Die Verwendung des Filters ist obligatorisch, da in allen analogen Telefonleitungen in der Schweiz Zeitsteuertakte vorhanden sind.
Questo prodotto richiede un filtro toni Billing svizzero, (codice Lexmark 80D1877) da installare su tutte le linee che ricevono impulsi remoti in Svizzera. È necessario utilizzare il filtro poiché gli impulsi remoti sono presenti su tutte le linee analogiche in Svizzera.
This section contains the following regulatory information pertaining to wireless products that contain transmitters, for example, but not limited to, wireless network cards or proximity card readers.
The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
This device complies with Industry Canada specification RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device has been designed to operate only with the antenna provided. Use of any other antenna is strictly prohibited per regulations of Industry Canada.

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF fields in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada's Web site www.hc-sc.gc.ca/rpb
The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met.
Cet appareil est conforme à la norme RSS-210 d'Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes :
(1) cet appareil ne doit pas provoquer d'interférences et (2) il doit accepter toute interférence reçue, y compris celles risquant d'altérer son fonctionnement.
Cet appareil a été conçu pour fonctionner uniquement avec l'antenne fournie. L'utilisation de toute autre antenne est strictement interdite par la réglementation d'Industry Canada.
En application des réglementations d'Industry Canada, l'utilisation d'une antenne de gain supérieur est strictement interdite.
Pour empêcher toute interférence radio au service faisant l'objet d'une licence, cet appareil doit être utilisé à l'intérieur et loin des fenêtres afin de garantir une protection optimale.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'installateur de cet équipement radio doit veiller à ce que l'antenne soit implantée et dirigée de manière à n'émettre aucun champ HF dépassant les limites fixées pour l'ensemble de la population par Santé Canada. Reportez-vous au Code de sécurité 6 que vous pouvez consulter sur le site Web de Santé Canada www.hc-sc.gc.ca/rpb
Le terme « IC » précédant le numéro de d'accréditation/inscription signifie simplement que le produit est conforme aux spécifications techniques d'Industry Canada.
Products bearing the CE mark are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits, and on radio equipment and telecommunications terminal equipment.
Compliance is indicated by the CE marking.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product satisfies the Class A limits of EN 55022 and safety requirements of EN 60950.

Products equipped with 2.4GHz Wireless LAN option are in conformity with the protection requirements of EC Council directives 2004/108/EC, 2006/95/EC, and 1999/5/EC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility, safety of electrical equipment designed for use within certain voltage limits and on radio equipment and telecommunications terminal equipment.
Compliance is indicated by the CE marking.
Operation is allowed in all EU and EFTA countries, but is restricted to indoor use only.
The manufacturer of this product is: Lexmark International, Inc., 740 West New Circle Road, Lexington, KY, 40550 USA. The authorized representative is: Lexmark International Technology Hungária Kft., 8 Lechner Ödön fasor, Millennium Tower III, 1095 Budapest HUNGARY, A declaration of conformity to the requirements of the Directives is available upon request from the Authorized Representative.
This product may be used in the countries indicated in the table below.

AT BE BG CH CY CZ DE DK EE
EL ES FI FR HR HU IE IS IT
LI LT LU LV MT NL NO PL PT
Česky Společnost Lexmark International, Inc. tímto prohlašuje, že výrobek tento výrobek je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk Lexmark International, Inc. erklærer herved, at dette produkt overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch Hiermit erklärt Lexmark International, Inc., dass sich das Gerät dieses Gerät in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Ελληνική ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Η LEXMARK INTERNATIONAL, INC. ΔΗΛΩΝΕΙ ΟΤΙ ΑΥΤΟ ΤΟ ΠΡΟΪΟΝ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
English Hereby, Lexmark International, Inc., declares that this type of equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español Por medio de la presente, Lexmark International, Inc. declara que este producto cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Eesti Käesolevaga kinnitab Lexmark International, Inc., et seade see toode vastab direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele muudele asjakohastele sätetele.
Suomi Lexmark International, Inc. vakuuttaa täten, että tämä tuote on direktiivin 1999/5/EY oleellisten vaatimusten ja muiden sitä koskevien direktiivin ehtojen mukainen.
Français Par la présente, Lexmark International, Inc. déclare que l'appareil ce produit est conforme aux exigences fondamentales et autres dispositions pertinentes de la directive 1999/5/CE.
Magyar Alulírott, Lexmark International, Inc. nyilatkozom, hogy a termék megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski Ar šo Lexmark International, Inc. deklarē, ka šis izstrādājums atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių Šiuo Lexmark International, Inc. deklaruoja, kad šis produktas atitinka esminius reikalavimus ir kitas 1999/5/EB direktyvos nuostatas.
Malti Bil-preżenti, Lexmark International, Inc., jiddikjara li dan il-prodott huwa konformi mal-ħtiġijiet essenzjali u ma dispożizzjonijiet oħrajn relevanti li jinsabu fid-Direttiva 1999/5/KE.
Nederlands Hierbij verklaart Lexmark International, Inc. dat het toestel dit product in overeenstemming is met de essentiële
eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Norsk Lexmark International, Inc. erklærer herved at dette produktet er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE.
Slovensky Lexmark International, Inc. týmto vyhlasuje, že tento produkt spĺňa základné požiadavky a všetky
príslušné ustanovenia smernice 1999/5/ES.
Slovensko Lexmark International, Inc. izjavlja, da je ta izdelek v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.
Svenska Härmed intygar Lexmark International, Inc. att denna produkt står i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
STATEMENT OF LIMITED WARRANTY FOR LEXMARK LASER PRINTERS, LEXMARK LED PRINTERS, AND LEXMARK MULTIFUNCTION LASER PRINTERS
This limited warranty applies to the United States and Canada. For customers outside the U.S., refer to the country- specific warranty information that came with your product.
This limited warranty applies to this product only if it was originally purchased for your use, and not for resale, from Lexmark or a Lexmark Remarketer, referred to in this statement as “Remarketer.”
Lexmark warrants that this product:
—Is manufactured from new parts, or new and serviceable used parts, which perform like new parts
—Is, during normal use, free from defects in material and workmanship
If this product does not function as warranted during the warranty period, contact a Remarketer or Lexmark for repair or replacement (at Lexmark's option).

If this product is a feature or option, this statement applies only when that feature or option is used with the product for which it was intended. To obtain warranty service, you may be required to present the feature or option with the product.
If you transfer this product to another user, warranty service under the terms of this statement is available to that user for the remainder of the warranty period. You should transfer proof of original purchase and this statement to that user.
The warranty period starts on the date of original purchase as shown on the purchase receipt and ends 12 months later provided that the warranty period for any supplies and for any maintenance items included with the printer shall end earlier if it, or its original contents, are substantially used up, depleted, or consumed. Fuser Units, Transfer/Transport Units, Paper Feed items, if any, and any other items for which a Maintenance Kit is available are substantially consumed when the printer displays a “Life Warning” or “Scheduled Maintenance” message for such item.
To obtain warranty service you may be required to present proof of original purchase. You may be required to deliver your product to the Remarketer or Lexmark, or ship it prepaid and suitably packaged to a Lexmark designated location. You are responsible for loss of, or damage to, a product in transit to the Remarketer or the Lexmark designated location.
When warranty service involves the exchange of a product or part, the item replaced becomes the property of the Remarketer or Lexmark. The replacement may be a new or repaired item.
The replacement item assumes the remaining warranty period of the original product.
Replacement is not available to you if the product you present for exchange is defaced, altered, in need of a repair not included in warranty service, damaged beyond repair, or if the product is not free of all legal obligations, restrictions, liens, and encumbrances.
As part of your warranty service and/or replacement, Lexmark may update the firmware in your printer to the latest version. Firmware updates may modify printer settings and cause counterfeit and/or unauthorized products, supplies, parts, materials (such as toners and inks), software, or interfaces to stop working. Authorized use of genuine Lexmark products will not be impacted.
Before you present this product for warranty service, remove all print cartridges, programs, data, and removable storage media (unless directed otherwise by Lexmark).
For further explanation of your warranty alternatives and the nearest Lexmark authorized servicer in your area contact Lexmark on the World Wide Web.
Remote technical support is provided for this product throughout its warranty period. For products no longer covered by a Lexmark warranty, technical support may not be available or only be available for a fee.
Lexmark does not warrant uninterrupted or error-free operation of any product or the durability or longevity of prints produced by any product.
Warranty service does not include repair of failures caused by:
—Modification or unauthorized attachments
—Accidents, misuse, abuse or use inconsistent with Lexmark user’s guides, manuals, instructions or guidance
—Unsuitable physical or operating environment
—Maintenance by anyone other than Lexmark or a Lexmark authorized servicer
—Operation of a product beyond the limit of its duty cycle

—Use of printing media outside of Lexmark specifications
—Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts
—Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark
TO THE EXTENT PERMITTED BY APPLICABLE LAW, NEITHER LEXMARK NOR ITS THIRD PARTY SUPPLIERS OR REMARKETERS MAKE ANY OTHER WARRANTY OR CONDITION OF ANY KIND, WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS PRODUCT, AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND SATISFACTORY QUALITY. ANY WARRANTIES THAT MAY NOT BE DISCLAIMED UNDER APPLICABLE LAW ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS OR IMPLIED, WILL APPLY AFTER THIS PERIOD. ALL INFORMATION, SPECIFICATIONS, PRICES, AND SERVICES ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE.
Your sole remedy under this limited warranty is set forth in this document. For any claim concerning performance or nonperformance of Lexmark or a Remarketer for this product under this limited warranty, you may recover actual damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever will be limited to the amount you paid for the product that caused the damages. This limitation of liability will not apply to claims by you for bodily injury or damage to real property or tangible personal property for which Lexmark is legally liable. IN NO EVENT WILL LEXMARK BE LIABLE FOR ANY LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGE, OR OTHER ECONOMIC OR CONSEQUENTIAL DAMAGES. This is true even if you advise Lexmark or a Remarketer of the possibility of such damages. Lexmark is not liable for any claim by you based on a third party claim.
This limitation of remedies also applies to claims against any Suppliers and Remarketers of Lexmark. Lexmark's and its Suppliers' and Remarketers' limitations of remedies are not cumulative. Such Suppliers and Remarketers are intended beneficiaries of this limitation.
Some states do not allow limitations on how long an implied warranty lasts, or do not allow the exclusion or limitation of incidental or consequential damages, so the limitations or exclusions contained above may not apply to you.
This limited warranty gives you specific legal rights. You may also have other rights that vary from state to state.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Elliptic Curve Cryptography (ECC) Cipher Suites for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Elliptic Curve Cipher Suites with SHA-256/382 and AES Galois Counter Mode (GCM) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for TLS Suite B Profile for Transport Layer Security (TLS) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Addition of the Camellia Cipher Suites to Transport Layer Security (TLS) implemented in the product or service.

The use of certain patents in this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for AES-CCM ECC Cipher Suites for TLS implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for IKE and IKEv2 Authentication Using the Eliptic Curve Digital Signature Algorithm (ECDSA) implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Suite B Cryptographic Suites for IPSec implemented in the product or service.
The use of this product or service is subject to the reasonable, non-discriminatory terms in the Intellectual Property Rights (IPR) Disclosure of Certicom Corp. at the IETF for Algorithms for Internet Key Exchange version 1 (IKEv1) implemented in the product or service.








Pages referenced in this manual — manufacturer, support and downloads.
Owners and our team usually reply within a day — and your question helps the next person too.
Be the first to ask — other owners or our team will answer.