EN
Lexmark logo
Official user manual

Lexmark PRO710

55 pages·3.5 MB·Printer·PDF·ENDEFRITNLJA
Lexmark PRO710
Table of Contents 157 sections Contents · About your printer · Finding information about the printer · Minimizing your printer's environmental impact · … ShowHide
Contentsp.3About your printerp.5Finding information about the printerp.5Minimizing your printer's environmental impactp.5Printer modelsp.6Printer featuresp.6Setting up the printerp.6Understanding the parts of the printerp.12Using the printer control panelp.13Using flash drivesp.14Supported file typesp.14Using a flash drive with the printerp.15Ordering and replacing suppliesp.16Ordering ink cartridgesp.16Replacing ink cartridgesp.16Maintaining ink cartridgesp.18Aligning the printheadp.18Cleaning the printhead nozzlesp.18Using the printer softwarep.19Minimum system requirementsp.19Installing the printer softwarep.19Using the Windows printer softwarep.19Using the Macintosh printer softwarep.20Printingp.22Printing a documentp.22Printing on both sides of the paper (duplexing) automaticallyp.22Printing photos from a flash drivep.23Printing documents from a flash drivep.23Canceling print jobsp.23Printing from a mobile devicep.24What is LexPrint?p.24Supported printersp.24Copyingp.25Tips for copyingp.25Making copiesp.25Making a two-sided (duplex) copy automaticallyp.25Canceling copy jobsp.26Scanningp.27Tips for scanningp.27Scanning to a local computerp.27Scanning to a flash drive or memory cardp.27Scanning directly to e-mail using the printer softwarep.27Scanning to a PDFp.28Canceling scan jobsp.28E-mailingp.29Sending e-mailp.29Tips for e-mailingp.29Setting up the e-mail functionp.29Canceling an e-mailp.29Setting up the printer to faxp.30Step 1: Connect the printer to the telephone linep.30Scenario 1: Standard telephone linep.30Scenario 2: Digital Subscriber Line (DSL)p.32Scenario 3: VoIP telephone servicep.32Scenario 4: Digital telephone service through a cable providerp.33Scenario 5: Countryor region-specific setupp.34Step 2: Check the dial tonep.37Step 3: Set your fax name and fax numberp.37Step 4: Set the printer to receive faxes automatically or manuallyp.37Step 5: Set the number of ringsp.38Step 6: Create a contact listp.38Faxingp.39Sending faxesp.39Tips for sending faxesp.39Sending faxes using the printer control panelp.39Sending faxes using the computerp.39Receiving faxesp.39Tips for receiving faxesp.39Receiving faxes automaticallyp.40Receiving faxes manuallyp.40Wireless networkingp.41Information you will need to set up the printer on a wireless networkp.41Installing the printer on a wireless networkp.41What is Wi-Fi Protected Setup?p.41Configuring Wi-Fi Protected Setup manuallyp.42Use the Push Button Configuration (PBC) methodp.42Use the Personal Identification Number (PIN) methodp.42Troubleshootingp.43Before you troubleshootp.43If Troubleshooting does not solve your problemp.43Setup troubleshootingp.43Incorrect language appears on the displayp.43Change the language using the printer menusp.43Installation screen did not appear during installationp.43Launch the printer CD manuallyp.43Software did not installp.43Make sure that your computer meets the minimum system requirementsp.43Temporarily disable security programs in Windows before installing the softwarep.43Check the USB connectionp.44Reconnect the printer power supplyp.44Print job does not print or is missing pagesp.44Make sure the ink cartridges are inserted correctlyp.44Select your printer from the Print dialog before sending the print jobp.44Make sure the print job is not pausedp.44Make sure your printer is set as the default printerp.44Reconnect the printer power supplyp.44Remove and reconnect the USB cable connected to your printerp.44Check the USB connectionp.44Remove and reinstall the printer softwarep.44Printer is printing blank pagesp.44Reinstall the ink cartridges and deep clean and align the printheadp.44Printer is busy or does not respondp.45Make sure the printer is not in Sleep modep.45Reconnect the printer power supplyp.45Cannot delete documents from the print queuep.45Restart the computer and try againp.45Remove and reconnect the USB cable connected to your printerp.45Cannot print through USBp.45Check the USB connectionp.45Make sure the USB port is enabled in Windowsp.45Remove and reinstall the printer softwarep.45Fax troubleshootingp.45Fax troubleshooting checklistp.46Cannot send faxesp.46Make sure that you have registered your user information in the printerp.46Decrease the transmission speed of the fax modemp.46Enable error correctionp.46Enable automatic fax conversionp.46Make sure that the Dial Prefix setting is correctp.46Cannot receive faxesp.47Make sure that you have configured the correct settings for your setupp.47Make sure that the printer is connected to an analog portp.47Make sure that the printer memory is not fullp.47Make sure that Fax Forwarding is disabledp.47Increase the ringer volumep.47Make sure that you have the correct manual answer codep.47Cannot run the fax softwarep.47Make sure a fax driver is installedp.47Make sure the printer is connected to a telephone linep.47Wireless network troubleshootingp.47Wireless troubleshooting checklistp.47Printing a network setup pagep.48Locating IP addressesp.48Cannot print over wireless networkp.48Turn the access point (wireless router) off and then back onp.48Disconnect from VPN sessionp.48Make sure Demo Mode is turned offp.48Check your WEP key or WPA passphrasep.48Check if your access point has an association/registration buttonp.49Move your access point away from other electronic devicesp.49Move the computer and/or printer closer to the access pointp.49Check the wireless signal qualityp.49Check your advanced security settingsp.49Make sure your computer is connected to your access pointp.49Make sure that your computer and printer are connected to the same wireless networkp.49Make sure your OS is compatible with wireless printing through AirPortp.50“Communication not available” message appears when printing wirelesslyp.50Make sure your computer and printer have valid IP addresses for the networkp.50Make sure the wireless port is selectedp.51Make sure bidirectional communication is enabledp.51Noticesp.52Edition noticep.52UNITED STATES GOVERNMENT RIGHTSp.52Trademarksp.52Federal Communications Commission (FCC) compliance information statementp.52Federal Communications Commission (FCC) compliance information statementp.52Indexp.53
Page 1 of the Lexmark PRO710 user manual — December 2011 www.lexmark.com
Page 1 · click to enlarge
Page 1

December 2011 www.lexmark.com

Pro710 Series Quick Reference Guide

Page 2 of the Lexmark PRO710 user manual — Important Message About Cartridge Recycling!
Page 2 · click to enlarge
Page 2

printer except as otherwise provided below, and (2) pass this license/agreement to any subsequent user

restriction that they may be used only once. After this single use, the license to use the print cartridges

and their contents terminates, and you agree to return them only to Lexmark for recycling. Replacement

inkjet cartridge(s) sold without these terms are available through www.lexmark.com and may be refilled

Use only the power supply and power cord provided with this product or the manufacturer's authorized

electrical shock results. Inspect the power cord regularly for signs of such problems. Remove the

cord provided with this product or a UL Listed 26 AWG or larger replacement when connecting

this product or make any electrical or cabling connections, such as the fax feature, power cord,

Connect the power cord to a properly grounded electrical outlet that is near the product and easily

power cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord

of this printer. The patented Lexmark inkjet cartridges and their contents are licensed subject to a

between objects such as furniture and walls. If any of these things happen, a risk of fire or

by you, or a third party, as the only cartridge alternative to be used with the licensed printer.

power cord from the electrical outlet before inspecting it.

Do not place or use this product near water or wet locations.

this product to the public switched telephone network.

or telephone, during a lightning storm.

Important safety information

replacements.

accessible.

to participate in our easy, no-cost method for returning empty Lexmark cartridges to Lexmark for proper

This patented printer is licensed for, and designed to work with, only genuine Lexmark inkjet cartridges

for the life of the patented printer. You agree to: (1) use only genuine Lexmark inkjet cartridges with this

At Lexmark, we take our commitment to the environment seriously, and we encourage our customers

request postage-paid bags. Bags usually arrive within 7–10 days.

postage-paid return bag, and then seal the bag. If you’re sending

single-color tanks, we recommend that you send at least two at

Place the empty Lexmark-branded inkjet cartridge(s) in the

Mail the bag to Lexmark’s recycling partner. The bag is pre-

Lexmark-branded cartridges are always made with all new parts, though components may contain

Go to www.lexmark.com/recycle. Follow instructions to

recycling. We will insure that cartridges are properly handled with zero waste to landfills.

a time to maximize the environmental benefits.

Visit www.lexmark.com/recycle to learn more about recycling.

recycled material. For warranty returns, call 1-800-395-4039.

Please Read Before Opening Your Inkjet Cartridge Box

addressed.

Important Message About Cartridge Recycling!

Lexmark PRO710 — Important Message About Cartridge Recycling! diagram (page 2)
Fig. 1 · Important Message About Cartridge Recycling!
Lexmark PRO710 — Important Message About Cartridge Recycling! diagram (page 2)
Fig. 2 · Important Message About Cartridge Recycling!
Lexmark PRO710 — Important Message About Cartridge Recycling! diagram (page 2)
Fig. 3 · Important Message About Cartridge Recycling!
Lexmark PRO710 — Important Message About Cartridge Recycling! diagram (page 2)
Fig. 4 · Important Message About Cartridge Recycling!
Lexmark PRO710 — Important Message About Cartridge Recycling! diagram (page 2)
Fig. 5 · Important Message About Cartridge Recycling!
Lexmark PRO710 — Important Message About Cartridge Recycling! diagram (page 2)
Fig. 6 · Important Message About Cartridge Recycling!
Lexmark PRO710 — Important Message About Cartridge Recycling! diagram (page 2)
Fig. 7 · Important Message About Cartridge Recycling!
Lexmark PRO710 — Important Message About Cartridge Recycling! diagram (page 2)
Fig. 8 · Important Message About Cartridge Recycling!
Page 3 of the Lexmark PRO710 user manual — Table of Contents
Page 3 · Contents
Contents

Contents

Contentsp.3About your printerp.5Finding information about the printerp.5Minimizing your printer's environmental impactp.5Printer modelsp.6Printer featuresp.6Setting up the printerp.6Understanding the parts of the printerp.12Using the printer control panelp.13Using flash drivesp.14Supported file typesp.14Using a flash drive with the printerp.15Ordering and replacing suppliesp.16Ordering ink cartridgesp.16Replacing ink cartridgesp.16Maintaining ink cartridgesp.18Aligning the printheadp.18Cleaning the printhead nozzlesp.18Using the printer softwarep.19Minimum system requirementsp.19Installing the printer softwarep.19Using the Windows printer softwarep.19Using the Macintosh printer softwarep.20Printingp.22Printing a documentp.22Printing on both sides of the paper (duplexing) automaticallyp.22Printing photos from a flash drivep.23Printing documents from a flash drivep.23Canceling print jobsp.23Printing from a mobile devicep.24What is LexPrint?p.24Supported printersp.24Copyingp.25Tips for copyingp.25Making copiesp.25Making a two-sided (duplex) copy automaticallyp.25Canceling copy jobsp.26Scanningp.27Tips for scanningp.27Scanning to a local computerp.27Scanning to a flash drive or memory cardp.27Scanning directly to e-mail using the printer softwarep.27Scanning to a PDFp.28Canceling scan jobsp.28E-mailingp.29Sending e-mailp.29Tips for e-mailingp.29Setting up the e-mail functionp.29Canceling an e-mailp.29Setting up the printer to faxp.30Step 1: Connect the printer to the telephone linep.30Scenario 1: Standard telephone linep.30Scenario 2: Digital Subscriber Line (DSL)p.32Scenario 3: VoIP telephone servicep.32Scenario 4: Digital telephone service through a cable providerp.33Scenario 5: Countryor region-specific setupp.34Step 2: Check the dial tonep.37Step 3: Set your fax name and fax numberp.37Step 4: Set the printer to receive faxes automatically or manuallyp.37Step 5: Set the number of ringsp.38Step 6: Create a contact listp.38Faxingp.39Sending faxesp.39Tips for sending faxesp.39Sending faxes using the printer control panelp.39Sending faxes using the computerp.39Receiving faxesp.39Tips for receiving faxesp.39Receiving faxes automaticallyp.40Receiving faxes manuallyp.40Wireless networkingp.41Information you will need to set up the printer on a wireless networkp.41Installing the printer on a wireless networkp.41What is Wi-Fi Protected Setup?p.41Configuring Wi-Fi Protected Setup manuallyp.42Use the Push Button Configuration (PBC) methodp.42Use the Personal Identification Number (PIN) methodp.42Troubleshootingp.43Before you troubleshootp.43If Troubleshooting does not solve your problemp.43Setup troubleshootingp.43Incorrect language appears on the displayp.43Change the language using the printer menusp.43Installation screen did not appear during installationp.43Launch the printer CD manuallyp.43Software did not installp.43Make sure that your computer meets the minimum system requirementsp.43Temporarily disable security programs in Windows before installing the softwarep.43Check the USB connectionp.44Reconnect the printer power supplyp.44Print job does not print or is missing pagesp.44Make sure the ink cartridges are inserted correctlyp.44Select your printer from the Print dialog before sending the print jobp.44Make sure the print job is not pausedp.44Make sure your printer is set as the default printerp.44Reconnect the printer power supplyp.44Remove and reconnect the USB cable connected to your printerp.44Check the USB connectionp.44Remove and reinstall the printer softwarep.44Printer is printing blank pagesp.44Reinstall the ink cartridges and deep clean and align the printheadp.44Printer is busy or does not respondp.45Make sure the printer is not in Sleep modep.45Reconnect the printer power supplyp.45Cannot delete documents from the print queuep.45Restart the computer and try againp.45Remove and reconnect the USB cable connected to your printerp.45Cannot print through USBp.45Check the USB connectionp.45Make sure the USB port is enabled in Windowsp.45Remove and reinstall the printer softwarep.45Fax troubleshootingp.45Fax troubleshooting checklistp.46Cannot send faxesp.46Make sure that you have registered your user information in the printerp.46Decrease the transmission speed of the fax modemp.46Enable error correctionp.46Enable automatic fax conversionp.46Make sure that the Dial Prefix setting is correctp.46Cannot receive faxesp.47Make sure that you have configured the correct settings for your setupp.47Make sure that the printer is connected to an analog portp.47Make sure that the printer memory is not fullp.47Make sure that Fax Forwarding is disabledp.47Increase the ringer volumep.47Make sure that you have the correct manual answer codep.47Cannot run the fax softwarep.47Make sure a fax driver is installedp.47Make sure the printer is connected to a telephone linep.47Wireless network troubleshootingp.47Wireless troubleshooting checklistp.47Printing a network setup pagep.48Locating IP addressesp.48Cannot print over wireless networkp.48Turn the access point (wireless router) off and then back onp.48Disconnect from VPN sessionp.48Make sure Demo Mode is turned offp.48Check your WEP key or WPA passphrasep.48Check if your access point has an association/registration buttonp.49Move your access point away from other electronic devicesp.49Move the computer and/or printer closer to the access pointp.49Check the wireless signal qualityp.49Check your advanced security settingsp.49Make sure your computer is connected to your access pointp.49Make sure that your computer and printer are connected to the same wireless networkp.49Make sure your OS is compatible with wireless printing through AirPortp.50“Communication not available” message appears when printing wirelesslyp.50Make sure your computer and printer have valid IP addresses for the networkp.50Make sure the wireless port is selectedp.51Make sure bidirectional communication is enabledp.51Noticesp.52Edition noticep.52UNITED STATES GOVERNMENT RIGHTSp.52Trademarksp.52Federal Communications Commission (FCC) compliance information statementp.52Federal Communications Commission (FCC) compliance information statementp.52Indexp.53
Page 5 of the Lexmark PRO710 user manual — About your printer
Page 5 · click to enlarge
Page 5

About your printer 5

  • Return ink cartridges for reuse or recycling through the Lexmark Cartridge Collection Program. To return an ink cartridge, go to <a href="http://www.lexmark.com/recycle" rel="nofollow noopener" target="_blank">www.lexmark.com/recycle</a> , and then follow the instructions to request
  • Use high ‑ yield cartridges. These cartridges let you print more pages.
What are you looking for?Find it here Initial setup instructions• Quick Setup Sheet • Hardware Setup Wizard1 Additional setup and instructions for using the printerComprehensive User's Guide installed automatically with the printer software.2 For Windows users After installing your printer, you can access the User's Guide from the printer program folder: 1 Click or Start. 2 Click All Programs or Programs, and then select the printer program folder from the list. 3 Select User's Guide. For Macintosh users 1 From the Finder, navigate to: Applications > select your printer folder 2 Double‑click User's Guide. Help using the printer softwareSoftware Help installed automatically with the printer software.2 Click Help from any printer software program or application. The latest supplemental information, updates, online customer support, and telephone supportSupport Web site—http://support.lexmark.com 1 Available on the installation software CD. 2 Available on the installation software CD and on the Lexmark Support Web site at http://support.lexmark.com.
  • Recycle the product packaging.
  • Recycle your old printer instead of throwing it away.
  • Recycle paper from discarded print jobs.
  • Use recycled paper.

a postage‑paid bag.

Recycling

software.2 Click Help from any printer software program or

Support Web site—http://support.lexmark.com

1 From the Finder, navigate to: Applications > select your printer folder

Guide from the printer program folder:

2 Available on the installation software CD and on the Lexmark Support Web site at http://support.lexmark.com.

2 Double‑click User's Guide.

  • Initial setup instructions
  • Quick Setup Sheet
  • Hardware Setup Wizard 1

or Start.

3 Select User's Guide.

the printer software.2

Finding information about the printer

What are you looking for? Find it here

application.

For additional information, see the following:

Additional setup and instructions for using the

The latest supplemental information, updates,

1 Available on the installation software CD.

online customer support, and telephone

About your printer

faxing problems.

Show 4 more labels / short text on this page
For Macintosh users · For Windows users · 1 Click · support
Page 6 of the Lexmark PRO710 user manual — Printer models
Page 6 · click to enlarge
Page 6

About your printer 6

  • Do not attach the USB cable until prompted to do so.
  • Place the printer near the computer during setup. If you are setting up on a wireless network, then you may move the printer after setup is complete.
Lexmark PRO710 — Printer models diagram (page 6)
Fig. 9 · Printer models
Lexmark PRO710 — Printer models diagram (page 6)
Fig. 10 · Printer models
  • Contents may vary by model and region.

Setting up the printer

1 Unpack the printer.

  • Wireless or Ethernet networking —Print and scan from anywhere in your home or office over a secure wireless or Ethernet network, as well as share the printer among multiple computers.
  • Intuitive touch screen —Use the full ‑ featured color touch screen for fast, easy access to all the printer menus. The large screen also allows you to view and print photos directly from your digital camera or
  • Print —Print documents and PDFs quickly from a computer or from a USB flash drive. Built ‑ in two ‑ sided printing lets you save money and the environment.
  • Copy —Copy documents and photos with one ‑ touch, computer ‑ free black or color copying. Enjoy 25% to 400% reduction and enlargement capacity.
  • Scan —Scan documents and photos fast and easily with the high ‑ resolution scanner. Easily scan to a memory device or to multiple laptops or computers over a secure wireless network with up to 1200 dpi
  • Fax —Do standalone black and color faxing at 33.6Kbps modem speed. Other fax features include 99 speed dials, automatic redial, junk fax blocking, and caller ID.
  • SmartSolutions —Simplify printer tasks that you frequently repeat by creating and customizing your printer solutions. Using the SmartSolutions toolkit on the Web, you can choose the printer tasks that

you often perform, apply your custom settings, and download them to your printer as shortcuts that

  • Shortcuts —Save a set of frequently used printer settings available for a given task and then assign a shortcut name and shortcut number to it. When you want to perform a task with those settings, you

you can easily access anytime. You can also customize your printer with solutions that display your

can simply select the shortcut number on the printer instead of going through the usual process of

  • Eco ‑ Mode —Save energy by activating Eco ‑ Mode. It automatically dims the printer display light and puts the printer into Sleep mode after a specified period of inactivity.

Depending on the model, your printer comes with features that will help you manage and accomplish

To read the Lexmark Environmental Sustainability Report, visit www.lexmark.com/environment.

The installation software CD that came with your printer works for the following printer models:

  • Photo printing —Print high ‑ quality, long ‑ lasting photos directly from digital memory cards, PictBridge ‑ enabled digital cameras, or USB flash drives.

programs, depending on the features of the printer that you purchased.

online calendars, online photo albums, RSS feeds, and more.

memory device without using a computer.

adjusting the settings and options.

Printer features

printing and imaging tasks:

Printer models

optical resolution.

  • Lexmark Pro715
  • Lexmark Pro719
Page 7 of the Lexmark PRO710 user manual — Printer models
Page 7 · click to enlarge
Page 7

About your printer 7

With a CD or DVD drive (Windows/Macintosh)Without a CD or DVD drive or for Linux Note: If the installation screen does not appear after a minute, then see “Installation screen did not appear during installation” on page 43.Download the printer driver from www.lexmark.com.
Lexmark PRO710 — Printer models diagram (page 7)
Fig. 11 · Printer models
Lexmark PRO710 — Printer models diagram (page 7)
Fig. 12 · Printer models

a Remove the language sheet holder from the printer control panel.

Lexmark PRO710 — Printer models diagram (page 7)
Fig. 13 · Printer models

c Close the scanner unit.

2 To initiate printer setup using a computer, insert the installation software CD, or download the printer driver.

Lexmark PRO710 — Printer models diagram (page 7)
Fig. 14 · Printer models

With a CD or DVD drive (Windows/Macintosh) Without a CD or DVD drive or for Linux

4 If necessary, lift the scanner unit to replace the language sheet on the printer control panel.

Lexmark PRO710 — Printer models diagram (page 7)
Fig. 15 · Printer models

3 Remove tape and packing material from all areas of the printer.

minute, then see “Installation screen did not appear during

installation” on page 43.

Show 8 more labels / short text on this page
xxxx xx xxxxx · xxxx xx xxxxx · xxxx xx · xxxxxxxx · xxxxxxxx · xxxx xx · xxxxxxxx · xxxxxxxx
Page 8 of the Lexmark PRO710 user manual — Printer models
Page 8 · click to enlarge
Page 8

About your printer 8

Lexmark PRO710 — Printer models diagram (page 8)
Fig. 16 · Printer models
Lexmark PRO710 — Printer models diagram (page 8)
Fig. 17 · Printer models
Lexmark PRO710 — Printer models diagram (page 8)
Fig. 18 · Printer models

Overloading the tray can cause paper jams.

8 Load paper and adjust the paper guides.

10 Connect the power cord only.

9 Insert the paper tray.

Lexmark PRO710 — Printer models diagram (page 8)
Fig. 19 · Printer models
Lexmark PRO710 — Printer models diagram (page 8)
Fig. 20 · Printer models
Lexmark PRO710 — Printer models diagram (page 8)
Fig. 21 · Printer models

7 For A4‑ or legal‑size paper, extend the paper tray.

Lexmark PRO710 — Printer models diagram (page 8)
Fig. 22 · Printer models

6 Move the paper guides to the sides.

Page 9 of the Lexmark PRO710 user manual — Printer models
Page 9 · click to enlarge
Page 9

About your printer 9

Lexmark PRO710 — Printer models diagram (page 9)
Fig. 23 · Printer models

Please choose a country or region and press OK

14 Set the country or region, and then press .

15 Set the date, and then press .

16 Set the time, and then press .

Lexmark PRO710 — Printer models diagram (page 9)
Fig. 24 · Printer models

12 Set the language on the printer control panel, and then press .

You have chosen English

as the language for your

13 Confirm the language, and then press .

Language Selection Language Selection

11 Make sure the printer is on.

Yes No · Are you sure? · Printer

Page 10 of the Lexmark PRO710 user manual — Printer models
Page 10 · click to enlarge
Page 10

About your printer 10

20 Enter your name or company name, and then press . Your fax name identifies you as the sender

Lexmark PRO710 — Printer models diagram (page 10)
Fig. 25 · Printer models
Lexmark PRO710 — Printer models diagram (page 10)
Fig. 26 · Printer models

You can now print, but there are additional steps required to access all the

Get my printer ready to scan directly to my computer

Get my printer ready to send and receive faxes

What will I be missing if I don’t do this now?

Fax Setup Do you want to set up fax now? NowLater

in all your sent faxes.

18 To configure basic fax functions, press the arrow buttons until Now is highlighted on the display, and

19 Enter your fax number for the printer, and then press . Your fax number identifies you as the sender

(UTC-05:00) Eastern Time (USA/Ca..

(UTC-06:00) Central Time (USA/Ca...

(UTC-07:00) Mountain Time (USA/C...

Please choose a time zone and press OK

to set up fax now?

Enter Fax Number and press OK

17 Set the time zone, and then press .

Time Zone Time Zone

Fax Setup Fax Setup

Fax Number Fax Number

in all your sent faxes.

then press .

Now Later · Do you want

Page 11 of the Lexmark PRO710 user manual — INK COMPATIBILITY CHART
Page 11 · click to enlarge
Page 11

About your printer 11

24 Insert each ink cartridge. Slide your finger along the ink cartridge until the cartridge clicks into place.

  • Install the color ink cartridges first. Then, use two hands to install the black cartridge.
  • Install the new ink cartridges immediately after removing the protective cap to avoid exposing the ink to air.
Lexmark PRO710 — Printer models diagram (page 11)
Fig. 27 · Printer models

The customer support label that is located near the ink cartridge access area contains the ink

compatibility information, model number, product Web site, and technical support number.

Lexmark PRO710 — Printer models diagram (page 11)
Fig. 28 · Printer models

x

MAC: XX

150, 150A, 150XL, 150XLA, 155, 155A Magenta 150, 150A, 150XL, 150XLA, 155, 155A Yellow 150, 150A, 150XL, 150XLA, 155, 155A, 155XL, 155XLA Black 150, 150A, 150XL, 150XLA, 155, 155A Cyan

MT/MN: 4449-70E

www.lexmark.com

Lexmark PRO710 — MT/MN: 4449-70E diagram (page 11)
Fig. 29

INK COMPATIBILITY CHART

25 Close the printer.

Lexmark PRO710 — INK COMPATIBILITY CHART diagram (page 11)
Fig. 30
Lexmark PRO710 — INK COMPATIBILITY CHART diagram (page 11)
Fig. 31

23 Unpack the ink cartridges.

22 Open the printer.

V725w

Page 12 of the Lexmark PRO710 user manual — Understanding the parts of the printer
Page 12 · click to enlarge
Page 12

About your printer 12

Lexmark PRO710 — Understanding the parts of the printer diagram (page 12)
Fig. 32 · Understanding the parts of the printer

5 ADF tray Load original documents into the ADF. This is recommended for scanning,

Feeder (ADF) Scan, copy, or fax multiple‑page letter‑, legal‑, and A4‑size documents.

as magazine clippings) into the ADF. Place these items on the scanner

Lexmark PRO710 — Understanding the parts of the printer diagram (page 12)
Fig. 33 · Understanding the parts of the printer

4 ADF paper guide Keep paper straight when feeding into the ADF.

6 ADF output tray Hold documents as they exit from the ADF.

2 Scanner glass Scan, copy or fax photos and documents.

Understanding the parts of the printer

Lexmark PRO710 — Understanding the parts of the printer diagram (page 12)
Fig. 34 · Understanding the parts of the printer
Use theTo 1Scanner coverAccess the scanner glass. 2Scanner glassScan, copy or fax photos and documents. 3Automatic Document Feeder (ADF)Scan, copy, or fax multiple‑page letter‑, legal‑, and A4‑size documents. 4ADF paper guideKeep paper straight when feeding into the ADF. 5ADF trayLoad original documents into the ADF. This is recommended for scanning, copying, or faxing multiple-page documents. Note: Do not load postcards, photos, small items, or thin media (such as magazine clippings) into the ADF. Place these items on the scanner glass. 6ADF output trayHold documents as they exit from the ADF. 7PictBridge and USB portConnect a PictBridge‑enabled digital camera or a flash drive to the printer. 8Printer control panelOperate the printer. 9Paper trayLoad paper. 10Paper stopCatch the paper as it exits. 11Paper exit trayHold paper as it exits.
  • The alignment page prints.
  • Do not remove the page until printing is finished. The alignment page may take a while to print.
  • Streaks on the alignment page are normal and not an indication of a problem.
  • The alignment page that prints may differ from the one shown.
  • Recycle the alignment page.
Lexmark PRO710 — Understanding the parts of the printer diagram (page 12)
Fig. 35 · Understanding the parts of the printer
Lexmark PRO710 — Understanding the parts of the printer diagram (page 12)
Fig. 36 · Understanding the parts of the printer

27 From the printer control panel, press to print an alignment page.

26 Extend and flip out the paper stop.

Page 13 of the Lexmark PRO710 user manual — EXT
Page 13 · click to enlarge
Page 13

About your printer 13

Lexmark PRO710 — Using the printer control panel diagram (page 13)
Fig. 37 · Using the printer control panel
Lexmark PRO710 — Using the printer control panel diagram (page 13)
Fig. 38 · Using the printer control panel

3 Arrow buttons Navigate to menu or submenu items that appear on the display.

4 Home Navigate from any level in the menu back to the home screen.

1 2 3 4 5

and hold for three seconds to turn off the printer.

Lexmark PRO710 — 1 2 3 4 5 diagram (page 13)
Fig. 39
  • 1 Power
  • Turn the printer on and off.
  • Switch to Sleep mode.

Using the printer control panel

14 Ethernet port Connect your printer to a computer, a local network, an external DSL, or

16 LINE port Connect the printer to an active telephone line (through a standard wall

printer and the telephone line. Use this port if you do not have a dedicated

fax line for the printer, and if this connection method is supported in your

17 EXT port Connect additional devices (telephone or answering machine) to the

Lexmark PRO710 — Using the printer control panel diagram (page 13)
Fig. 40 · Using the printer control panel

18 19 20

18 Power supply with port Connect the printer to a power source using the power cord.

jack, DSL filter, or VoIP adapter) to send and receive faxes.

plugging in or removing a USB cable or installation cable.

15 USB port Connect the printer to a computer using a USB cable.

13 Ink cartridge access area Install, replace, or remove the ink cartridges.

  • 19 Duplex unit
  • Print on both sides of a sheet of paper.
  • Remove paper jams.
Lexmark PRO710 — 18 19 20 diagram (page 13)
Fig. 41

EXT

LINE

EXT

LINE

12 Scanner unit Access the ink cartridges.

country or region.

a cable modem.

Lexmark PRO710 — EXT diagram (page 13)
Fig. 42

Use the To

Page 14 of the Lexmark PRO710 user manual — Supported file types
Page 14 · click to enlarge
Page 14

About your printer 14

10 Dial tone Dial the telephone number manually using the keypad before sending the fax.

  • 15 Cancel
  • Cancel a print, copy, scan, or fax job in progress.
  • Exit from a menu level of the Copy, Scan, Fax, Photo, or File Print menu to the top level of a menu.
  • Exit from a menu level of the Setup menu to the top level of the previous mode.

Check the network connection status of your printer and access the network

  • Clear current settings or error messages, and return to default settings.
  • 18 Eco ‑ Mode
  • Change to Sleep mode after the printer is left idle for 10 minutes.
  • Set screen brightness to low.

11 Address Book Access fax numbers from a saved list of numbers.

14 Start Start a job, depending on which mode is selected.

Check the wireless connection of your printer.

13 Black Switch to black‑and‑white mode.

12 Color Switch to color mode.

  • .pdf (Adobe Portable Document Format)

settings.

Using flash drives

Supported file types

17 Wi‑Fi indicator

Documents:

  • 7 Select
  • Select menu options.
  • Save settings.
  • Feed or eject paper. Press and hold the button for three seconds to feed or eject paper from the printer.

8 Redial Display the last number dialed. Press the left or right arrow button to view the

  • Enter fax numbers.
  • Operate an automated answering system.
  • Select letters when creating a Speed Dial list.
  • Type numbers to enter or edit the date and time shown on the display.

9 Pause Insert a three-second pause in a fax number to wait for an outside line or get

through an automated answering system. Enter a pause only when you have

Enter the number of copies or prints you want to make.

  • 6 Back
  • Return to the previous screen.
  • Exit from one menu level to a higher one.

already begun entering the number.

5 Keypad In Copy mode or Photo mode:

last five numbers dialed.

In Fax mode:

16 Network indicator · Use To

Page 15 of the Lexmark PRO710 user manual — Using a flash drive with the printer
Page 15 · click to enlarge
Page 15

About your printer 15

Make sure the flash drive contains files that are supported by the printer. For more information, see

device, or the printer in the areas shown while actively

printing, reading, or writing from the memory device. A

any network adapter, any connector, the memory

  • The flash drive uses the same port that is used for a PictBridge camera cable.
  • An adapter may be necessary if your flash drive does not fit directly into the port.

2 Follow the instructions or select from available options on the printer display.

Lexmark PRO710 — Using a flash drive with the printer diagram (page 15)
Fig. 43 · Using a flash drive with the printer

loss of data can occur.

Lexmark PRO710 — Using a flash drive with the printer diagram (page 15)
Fig. 44 · Using a flash drive with the printer
  • .jpg, .jpeg, .jpe (Joint Photographic Experts Group)
  • .tiff, .tif (Tagged Image File Format)

Using a flash drive with the printer

1 Insert a flash drive into the USB port.

“Supported file types” on page 14.

Images:

Page 16 of the Lexmark PRO710 user manual — Ordering ink cartridges
Page 16 · click to enlarge
Page 16

Ordering and replacing supplies 16

Make sure you have a new ink cartridge or cartridges before you begin. You must install new cartridges

  • To get more ink, order high ‑ yield ink cartridges.
  • Depending on your country or region, you may get the ink cartridges individually or in packs.
  • You can order a mix of standard ink cartridges and high ‑ yield ink cartridges, depending on your needs.

immediately after removing the old ones, or the ink remaining in the printhead nozzles may dry out.

  • Check the yield rate on the ink cartridge box, or visit <a href="http://www.lexmark.com/yields" rel="nofollow noopener" target="_blank">www.lexmark.com/yields</a> .
  • For best results, use only Lexmark ink cartridges.
  • The cartridges can be used for printing documents and photos.
  • When storing new ink cartridges, make sure they are unopened and placed on their flat side.
  • Remove ink cartridges from their packaging only upon installation.

Replacing ink cartridges

Removing ink cartridges

1 Turn on your printer.

Lexmark PRO710 — Removing ink cartridges diagram (page 16)
Fig. 45 · Removing ink cartridges
Lexmark PRO710 — Removing ink cartridges diagram (page 16)
Fig. 46 · Removing ink cartridges

1 Licensed for a single use only. After use, return this cartridge to Lexmark for remanufacturing, refilling, or recycling.

1 Licensed for a single use only. After use, return this cartridge to Lexmark for remanufacturing, refilling, or recycling.

Cartridge1 Regular cartridge2

cartridge1 Regular cartridge2

Cyan color cartridge 150 Not Available

Black cartridge 150 Not available

Yellow color cartridge 150 Not available

Magenta color cartridge 150 Not available

Black cartridge 160 Not available

Yellow color cartridge 160 Not available

Cyan color cartridge 160 Not available

Magenta color cartridge 160 Not available

High‑yield black cartridge 150XL, 155XL 150XLA

High‑yield yellow color cartridge 150XL 150XLA

High‑yield cyan color cartridge 150XL 150XLA

High‑yield magenta color cartridge 150XL 150XLA

High‑yield black cartridge 160 XL 160 XLA

High‑yield yellow color cartridge 160 XL 160 XLA

High‑yield cyan color cartridge 160 XL 160 XLA

High‑yield magenta color cartridge 160 XL 160 XLA

Ordering and replacing supplies

2 Available only on the Lexmark Web site at www.lexmark.com.

2 Available only on the Lexmark Web site at www.lexmark.com.

Ordering ink cartridges

Lexmark Pro710 Series except Pro719

Item Return Program · Item Return Program · Lexmark Pro719 model

Page 17 of the Lexmark PRO710 user manual — INK COMPATIBILITY CHART
Page 17 · click to enlarge
Page 17

Ordering and replacing supplies 17

2 Insert each ink cartridge. Slide your finger along the ink cartridge until the cartridge clicks into place.

  • Insert the color cartridges first, and then the black cartridge.
  • Insert the new ink cartridges immediately after removing the protective cap to avoid exposing the ink to air.
Lexmark PRO710 — Ordering and replacing supplies diagram (page 17)
Fig. 47 · Ordering and replacing supplies
Lexmark PRO710 — Ordering and replacing supplies diagram (page 17)
Fig. 48 · Ordering and replacing supplies

If your ink cartridge comes with a twist cap, then remove the cap.

Lexmark PRO710 — Ordering and replacing supplies diagram (page 17)
Fig. 49 · Ordering and replacing supplies
Lexmark PRO710 — Ordering and replacing supplies diagram (page 17)
Fig. 50 · Ordering and replacing supplies

3 Close the printer.

1 Remove the ink cartridge from the pack, and then remove the protective cap from the ink cartridge.

Lexmark PRO710 — Ordering and replacing supplies diagram (page 17)
Fig. 51 · Ordering and replacing supplies
Lexmark PRO710 — Ordering and replacing supplies diagram (page 17)
Fig. 52 · Ordering and replacing supplies

3 Press the release tab, and then remove the used ink cartridge or cartridges.

x

MAC: XX

150, 150A, 150XL, 150XLA, 155, 155A Magenta 150, 150A, 150XL, 150XLA, 155, 155A Yellow 150, 150A, 150XL, 150XLA, 155, 155A, 155XL, 155XLA Black 150, 150A, 150XL, 150XLA, 155, 155A Cyan

MT/MN: 4449-70E

www.lexmark.com

Lexmark PRO710 — MT/MN: 4449-70E diagram (page 17)
Fig. 53

INK COMPATIBILITY CHART

Installing ink cartridges

2 Open the printer.

V725w

Page 18 of the Lexmark PRO710 user manual — Aligning the printhead
Page 18 · click to enlarge
Page 18

Ordering and replacing supplies 18

In addition to the following tasks that you can perform, your printer performs an automatic maintenance

If you aligned the cartridges to improve print quality, then print your document again. If print quality has

If you have not been using the printer for a long period, then you may need to clean the printhead nozzles

to improve the quality of your prints. Keep your printer plugged to a properly grounded, working electrical

  • Cleaning the printhead nozzles uses ink, so clean them only when necessary.
  • Deep cleaning uses more ink, so try the Clean Printhead option first to save ink.
  • If the ink levels are too low, you must replace the ink cartridges before you can clean the printhead nozzles.

If the characters or lines on your printed image appear jagged or wavy, then you may need to align the

cycle every week if it is plugged into an electrical outlet. It will briefly come out of Sleep mode or will

3 Press the up or down arrow button to scroll to Clean Printhead or Deep Clean

> Setup > >Maintenance > > Align Printer >

outlet to allow it to perform automatic maintenance cycles.

2 From the printer control panel, navigate to:

not improved, then clean the printhead nozzles.

2 From the printer control panel, navigate to:

Maintaining ink cartridges

Cleaning the printhead nozzles

> Setup > > Maintenance >

Printhead, and then press .

temporarily turn on if it is turned off.

Aligning the printhead

An alignment page prints.

A cleaning page prints.

1 Load plain paper.

1 Load paper.

printhead.

Page 19 of the Lexmark PRO710 user manual — Supported operating systems
Page 19 · click to enlarge
Page 19

Using the printer software 19

3 Double-click the software installer package, and then follow the instructions on the computer screen.

When you set up the printer using the installation software CD, all the necessary software was installed.

software CD, run the installation software, and then click Advanced Options > Install Additional Software.

b In the Start Search or Run box, type D:\setup.exe, where D is the letter of your CD or DVD

You may have chosen to install some additional programs. The following table provides an overview of

If you did not install these additional programs during initial installation, then reinsert the installation

If the installation dialog does not appear after a minute, then click the CD icon on the desktop.

If the installation dialog screen does not appear after a minute, then launch the CD manually:

SUPPORT & DOWNLOADS > select your printer > select your operating system

3 Click Install, and then follow the instructions on the computer screen.

1 Go to the Lexmark Web site at http://support.lexmark.com.

Software installed during printer installation

3 Download the driver, and then install the printer software.

Using the Windows printer software

various software programs and what they can help you do.

Installing the printer software

, or click Start and then click Run.

then uninstall the current software first.

1 Close all open software programs.

2 Insert the installation software CD.

2 Insert the installation software CD.

c Press Enter, or click OK.

1 Close all open applications.

For Macintosh users

select all packages listed.

For Windows users

Using the Internet

2 Navigate to:

drive.

* The printer driver for this operating system is available only at http://support.lexmark.com.

The printer software requires up to 500MB of free disk space.

Using the printer software

Minimum system requirements

  • Red Hat Enterprise Linux WS 6, WS 5, and WS 4 *
  • Microsoft Windows 7 (SP1)
  • Microsoft Windows Server 2008 (R2 SP1)
  • Microsoft Windows Server 2008 (SP1)
  • Microsoft Windows Server 2003 (SP2)
  • Microsoft Windows Vista (SP1)
  • Microsoft Windows XP (SP3)
  • Macintosh Intel OS X version 10.7.0 or later
  • Macintosh Intel OS X version 10.6.0 or later
  • Macintosh Intel OS X version 10.5.0 or later
  • Macintosh Intel OS X version 10.4.4 or later
  • Macintosh PowerPC OS X version 10.5.0 or later
  • Macintosh PowerPC OS X version 10.4.0 or later
  • Ubuntu Linux 11.04, 10.10, 10.04, and 9.04 LTS *
  • SUSE Linux Enterprise Desktop 11 and 10 *
  • SUSE Linux Enterprise Server 11 and 10 *
  • Linux openSUSE 11.4, 11.3, and 11.2 *

Supported operating systems

  • Debian GNU/Linux 6.0 and 5.0 *
  • Red Flag Linux Desktop 6.0 *
  • Linpus Linux Desktop 9.6 *
  • PCLinux OS 2010 *
  • Mint 10 and 9 *
  • Fedora 14 *

a Click

Page 20 of the Lexmark PRO710 user manual — Printer software
Page 20 · click to enlarge
Page 20

Using the printer software 20

Printing Preferences When you click File > Print > Properties with a document open, a Printing

Preferences dialog appears. The dialog lets you select options for the

  • Select the number of copies to print.
  • Print two ‑ sided copies.
  • Select the paper type.
  • Add a watermark.
  • Enhance images.
  • Save settings.

programs, depending on the features of the printer that you purchased.

Use the Print dialog to adjust the print settings and schedule print jobs.

  • Printer Settings
  • Customize settings for fax jobs.
  • Create and edit the Contacts list.
  • Configure e ‑ mail connectivity settings.
  • Configure the language, country, date, and time.

Uninstaller Remove the printer software from your computer.

print job, such as the following:

Using the Macintosh printer software

Assistant Set up the printer on a wireless network.

Shortcuts Speed up usual tasks with your printer.

2 Double‑click the application that you want to use.

With a document or photo open, choose File > Print.

printer has wireless capability.

software.

Applications > select your printer folder

Launching the Print dialog

Launching an application

1 From the Finder, navigate to:

Product Update Receive automatic notifications of updates to your printer software

Abbyy Sprint OCR Scan a document and produce text that you can edit with a

Status Messenger Learn more about the printing problems encountered.

  • Set up the wireless printer on a wireless network.
  • Change the wireless settings of the printer.

(referred to as Tools for Office) Access your favorite settings in Microsoft Office 2007.

Printer Setup Utility Configure the fax and e‑mail settings of your printer.

  • Status Monitor Center
  • Check the supplies status of your printer.
  • Order supplies online.
  • (referred to as Printer Home)
  • Launch applications or programs.
  • Scan or e ‑ mail a photo or document.
  • Edit scanned documents.
  • Scan documents to PDF.
  • Adjust settings for the printer.
  • Order supplies.
  • Maintain ink cartridges.
  • Register the printer.
  • Contact technical support.
  • Access the User's Guide .

if the printer has wireless capability.

when new updates are available.

(referred to as Phone Book) Manage your fax contacts.

word‑processing program.

Lexmark Wireless Setup Utility

(referred to as Wireless Setup

LexmarkTM Printer Home

Lexmark Tools for Office

Printer software

Show 6 more labels / short text on this page
Use the To · Use the To · Wireless Setup · Use the To · Lexmark Phone Book · Utility)
Page 21 of the Lexmark PRO710 user manual — Accessing Web links
Page 21 · click to enlarge
Page 21

Using the printer software 21

  • Your printer may not come with these applications, depending on the features of the printer that you purchased or the installation type (standard or custom) chosen when you installed the printer.
  • To take advantage of the full features of your printer, select the custom install option during installation, and then select all packages listed.

Lexmark Software Updates Download and install the latest printer software.

Web links are links to predefined Web pages that are saved in the printer folder.

  • Visit Lexmark SmartSolutions
  • Visit the SmartSolutions Web site.
  • Choose your custom solutions.

Customer Support Contact customer support.

Lexmark Online Visit the Lexmark Web site.

Order Supplies Online Order ink or supplies.

Printer Registration Register your printer.

Applications > select your printer folder > Web Links

2 Double‑click the Web link that you want to visit.

1 From the Finder, navigate to:

Accessing Web links

you purchased.

Use To

Page 22 of the Lexmark PRO710 user manual — Printing
Page 22 · click to enlarge
Page 22

9 From the Two‑Sided pop‑up menu, choose Long‑Edge binding or Short‑Edge binding. • For Long‑Edge binding, pages are bound along the long edge of the page (left edge for portrait, top edge for landscape).

  • Click Long edge for print jobs with pages that are bound along the long edge of the page.
  • Click Short edge for print jobs with pages that are bound along the short edge of the page.

To return to single-sided printing, repeat steps 1 and 2, and then navigate to:

2 From the Page Setup dialog, set the printer, paper size, and orientation.

4 Click the Paper/Finishing tab, and then select a supported paper type.

Layout tab > Print on Both Sides (Duplex) area > Print on both sides

Layout tab > Print on Both Sides (Duplex) area > Print on one side only

7 From the Paper Type pop‑up menu, choose a supported paper type.

6 From the print options pop‑up menu, choose Quality & Media.

8 From the print options pop‑up menu, choose Layout.

5 From the Printer pop‑up menu, choose your printer.

1 With a document open, choose File > Page Setup.

5 Click OK to close any printer software dialogs.

4 From the menu bar, choose File > Print.

For Macintosh users

6 Click OK or Print.

3 Navigate to:

3 Click OK.

6 From the print options menu, choose the print quality, the number of copies to print, the type of paper to use, and how the pages should print.

3 Select the print quality, the number of copies to print, the type of paper to use, and how the pages should print.

  • The automatic duplex unit supports A4 ‑ and letter ‑ size paper. It also supports plain, premium plain, ColorLok certified plain, heavy plain, and letterhead paper types.

Printing on both sides of the paper (duplexing)

2 From the Page Setup dialog, set the printer, paper size, and orientation.

5 From the Printer pop‑up menu, choose your printer.

1 With a document open, choose File > Page Setup.

  • Do not remove the page until printing is finished.

2 Click Properties, Preferences, Options, or Setup.

2 Click Properties, Preferences, Options, or Setup.

4 Click OK to close any printer software dialogs.

1 With a document open, click File > Print.

4 From the menu bar, choose File > Print.

1 With a document open, click File > Print.

Printing a document

For Windows users

For Macintosh users

automatically

For Windows users

5 Click OK or Print.

Printing

7 Click Print.

3 Click OK.

Printing 22 · Portrait Landscape

Page 23 of the Lexmark PRO710 user manual — Printing photos from a flash drive
Page 23 · click to enlarge
Page 23

If document files and image files are stored on the memory device, then press the left or right arrow

3 Press the up or down arrow button to scroll to the document, and then press to select the document

4 From the Print Options menu screen, use the arrow buttons to select your printing options, and then

To cancel a print job from the printer control panel, press , and then press . Printing stops and the

5 Cancel the print job: • If you want to cancel a particular print job, then right‑click the document name, and then select Cancel.

2 If document files are stored on the memory device, then the printer automatically switches to File Print mode.

When the printer detects the memory device, Storage Device Detected appears on the

  • If you want to cancel all print jobs in the queue, then click Printer > Cancel All Documents .

saving options. You can also enhance sharpness, and use separator sheets.

4 Right‑click the printer, and then select Open or See what's printing.

2 In the Start Search or Run box, type control printers.

2 Choose the job you want to cancel, and then click Delete.

To cancel a print job from the computer, do the following:

button to scroll to Documents, and then press .

, or click Start and then click Run.

1 Click the printer icon on the Dock.

printer returns to the home screen.

The print queue dialog appears.

Canceling print jobs

The printers folder opens.

press , if necessary.

3 Press Enter, or click OK.

For Macintosh users

For Windows users

for printing.

5 Press .

display.

  • For Short ‑ Edge binding, pages are bound along the short edge of the page (top edge for portrait, left edge for landscape).
  • Print Photos allows you to print all photos, selected photos by photo range, and print photos using predefined photo size templates.

4 To adjust the print settings, press the up or down arrow button to scroll to the option you want to set,

Make sure the flash drive contains document files that are supported by the printer. For more information,

If image files and document files are stored in the memory device, then press the left or right arrow

  • Select and Print allows you to choose a layout, the number of photos per page, paper settings, photo size, photo quality, and to sharpen the quality of graphics.

and then press the left or right arrow button to scroll to the setting you want. If necessary, press

Lexmark PRO710 — For Macintosh users diagram (page 23)
Fig. 54 · For Macintosh users

3 Use the up or down arrow button to select a photo printing option, and then press .

2 Insert a flash drive or digital camera set to mass storage mode.

Printing documents from a flash drive

Printing photos from a flash drive

button to select Photos, and then press .

Lexmark PRO710 — Printing photos from a flash drive diagram (page 23)
Fig. 55 · Printing photos from a flash drive

see “Supported file types” on page 14.

to make a selection.

1 Load photo paper.

1 Insert a flash drive.

10 Click Print.

5 Press .

storing.

Printing 23 · 1 Click · Portrait Landscape

Page 24 of the Lexmark PRO710 user manual — Supported printers
Page 24 · click to enlarge
Page 24

photo album, or photos you recently captured using the camera of your mobile device, depending on its

Depending on your Lexmark printer model, you may need to download the LexPrint Listener application

LexPrint enables your mobile device to communicate with Lexmark printers found on the same network.

  • For select printer models that support Direct Image and Zeroconf or Bonjour, you can print directly from your mobile device to the printer without using LexPrint Listener. To check if your printer model
  • For other Lexmark printers, your mobile device can send print jobs to your printer as long as the printer software and LexPrint Listener are installed on the computer where the printer is connected.

Lexmark printer connected to the same wireless network. It lets you print Web pages, photos from the

LexPrint is a free application that lets you print easily from your iPad, iPhone, or iPod touch using any

features. You can also customize print settings from your mobile device.

supports these features, visit www.lexmark.com/lexprint.

Printing from a mobile device

from our Web site at www.lexmark.com/lexprint.

Supported printers

What is LexPrint?

Apple Inc.

Printing 24

Page 25 of the Lexmark PRO710 user manual — Tips for copying
Page 25 · click to enlarge
Page 25

5 From the Copy menu screen, press the up or down arrow button to scroll to the option you want to set, and then press the left or right arrow button to scroll to the setting you want. If necessary, press

The automatic duplex unit supports A4‑ and letter‑size paper. If you need to make two‑sided copies using

  • 4 Press the left or right arrow button to select a two ‑ sided copying option:
  • If you are copying a one ‑ sided document, then press the arrow buttons to scroll to 1 ‑ sided to 2 ‑ sided .
  • If you are copying a two-sided document and using the scanner glass, then press the arrow buttons to scroll to 2 ‑ sided to 2 ‑ sided .
  • If you want to specify the page orientation and layout of the original document and the copy, then

press the arrow buttons to scroll to Advanced. Press every time you make a selection, and

  • For long-edged binding, pages are bound along the long edge of the page (left edge for portrait orientation and top edge for landscape orientation).

When you select color or black‑only printing, the light that corresponds to your choice comes on.

2 Load an original document faceup into the ADF or facedown on the scanner glass.

2 Load the original document faceup into the ADF or facedown on the scanner glass.

Making a two ‑ sided (duplex) copy automatically

other paper sizes, then see the instructions for making a two‑sided copy manually.

4 Press the left or right arrow button to select the number of copies.

then press until you reach the Copy menu screen.

  • Press to switch to black ‑ and ‑ white mode.

3 From the printer control panel, navigate to:

3 From the printer control panel, navigate to:

  • Press to switch to color mode.

> Copy > > 2‑Sided Copies

> Copy > > Copies

to make a selection.

6 Select the copy mode:

1 Load paper.

7 Press .

Lexmark PRO710 — Making a two ‑ sided (duplex) copy automatically diagram (page 25)
Fig. 56 · Making a two ‑ sided (duplex) copy automatically
  • Make sure you load the original document faceup into the ADF or facedown at the placement corner of the scanner glass.
  • When using the ADF, adjust the paper guide on the ADF to the width of the original document.
  • When using the scanner glass, close the scanner cover, if possible, to avoid dark edges on the scanned image.

Use the scanner glass for single pages, small items

  • When the document to be copied is in place with the settings you want, press to start copying.
  • Do not load postcards, photos, small items, transparencies, photo paper, or thin media (such as magazine clippings) into the ADF. Place these items on the scanner glass.

you purchased a printer without an ADF, then load

original documents or photos on the scanner glass.

Lexmark PRO710 — Making a two ‑ sided (duplex) copy automatically diagram (page 25)
Fig. 57 · Making a two ‑ sided (duplex) copy automatically

Use the ADF for multiple‑page documents.

Lexmark PRO710 — Making a two ‑ sided (duplex) copy automatically diagram (page 25)
Fig. 58 · Making a two ‑ sided (duplex) copy automatically

Tips for copying

Making copies

Copying

1 Load paper.

Copying 25 · ADF Scanner glass

Page 26 of the Lexmark PRO710 user manual — Canceling copy jobs
Page 26 · click to enlarge
Page 26
  • For short-edged binding, pages are bound along the short edge of the page (top edge for portrait orientation and left edge for landscape orientation).

5 Press , and then follow the instructions on the display.

Scanning stops and the printer returns to the previous menu.

To cancel a copy job, press , and then press .

Canceling copy jobs

Copying 26

Page 27 of the Lexmark PRO710 user manual — Tips for scanning
Page 27 · click to enlarge
Page 27

Make sure you have set up your e‑mail settings before proceeding. For more information, see the section

3 Press the up or down arrow button to scroll to the scan option you want to set, and then press the left or right arrow button to scroll to the setting you want.

Set the color, quality, original image size, and other scan options. If necessary, press each time

4 Press the up or down arrow button to scroll to the scan option you want to set, and then press the left or right arrow button to scroll to the setting you want.

Set the color, quality, original image size, and other scan options. If necessary, press each time

Scanning directly to e ‑ mail using the printer software

1 Load the original document faceup into the ADF or facedown on the scanner glass.

1 Load an original document faceup into the ADF or facedown on the scanner glass.

Scanning to a flash drive or memory card

  • Some features are available only in select printer models.
  • Make sure your flash drive or memory card is not write ‑ protected.

The USB‑connected computer will receive the scan by default.

> Scan > > Computer > USB‑Connected Computer >

3 Insert the flash drive or memory card, and then press .

Follow the instructions on the printer display.

2 From the printer control panel, navigate to:

2 From the printer control panel navigate to:

> Scan > > Memory Device

on e‑mailing in the User’s Guide.

you make a selection.

you make a selection.

For Windows users

4 Press .

5 Press .

Lexmark PRO710 — For Windows users diagram (page 27)
Fig. 59 · For Windows users
  • Use the scanner glass when scanning two ‑ sided pages if your printer does not support duplex scanning or the ADF does not support the original document size.
  • When using the ADF, adjust the paper guide on the ADF to the width of the original document.
  • When using the scanner glass, close the scanner cover, if possible, to avoid dark edges on the scanned image.
  • When the document to be scanned is in place with the settings you want, press to start scanning.

Use the scanner glass for single pages, small items

  • Do not load postcards, photos, small items, transparencies, photo paper, or thin media (such as magazine clippings) into the ADF. Place these items on the scanner glass.

1 Load the original document faceup into the ADF or facedown on the scanner glass.

Scanning to a local computer

you purchased a printer without an ADF, then load

original documents or photos on the scanner glass.

Use the ADF for multiple‑page documents.

Tips for scanning

Scanning

Scanning 27 · ADF Scanner glass

Page 28 of the Lexmark PRO710 user manual — For Macintosh users
Page 28 · click to enlarge
Page 28

5 Set the application that supports the PDF format as the scan destination, and then start the scan job.

  • If you are sending the scan job using the printer software, then cancel the scan job from the software dialog.

application or search for Scanning an image in the Search field of the Help menu.

1 Load an original document faceup into the ADF or facedown on the scanner glass.

2 From the Applications folder in the Finder, launch the application you want to use.

? on the preview dialog for more information.

  • From the printer control panel, press , and then press .

Scanning stops and the printer returns to the previous menu.

Scanning starts and the scan progress dialog appears.

3 From the list of devices, select your printer.

4 Adjust the scan settings as needed.

Canceling scan jobs

5 Save the document as a PDF.

6 Save the document as a PDF.

Do one or more of the following:

For Macintosh users

Scanning starts and the scan progress dialog appears. When the scan is finished, a new e‑mail message

3 Click All Programs or Programs, and then select the printer program folder from the list.

application, or search for Scanning an image in the Search field of the Help menu.

3 Click All Programs or Programs, and then select the printer program folder from the list.

2 From the Applications folder in the Finder, launch the application you want to use.

1 Load an original document faceup into the ADF or facedown on the scanner glass.

1 Load an original document faceup into the ADF or facedown on the scanner glass.

5 Set the e‑mail application as the scan destination, and then start the scan job.

? on the preview dialog for more information.

is created with the scanned document automatically attached.

computer and then send it through e-mail as an attachment.

5 Select Email photo, Email document, or Email PDF.

Printer Home > select your printer > Scan > PDF

3 From the list of devices, select your printer.

Printer Home > select your printer > Scan

4 Adjust the scan settings as needed.

6 Compose your e‑mail message.

6 Compose your e‑mail message.

Scanning to a PDF

For Macintosh users

For Windows users

or Start.

or Start.

4 Navigate to:

4 Navigate to:

Capture.

Show 5 more labels / short text on this page
Scanning 28 · If applicable, click · If applicable, click · 2 Click · 2 Click
Page 29 of the Lexmark PRO710 user manual — For Macintosh users
Page 29 · click to enlarge
Page 29
  • If you are sending the e ‑ mail using the printer software, then cancel the e-mail from the software dialog.

2 Follow the instructions on the computer screen, and then click Save Settings.

Applications > select your printer folder > Printer Settings > Email

  • From the printer control panel, press , and then press .

Canceling an e ‑ mail

Do one or more of the following:

If necessary, make sure the network is connected to the Internet for the printer to communicate with

  • Use the scanner glass when scanning two ‑ sided pages if your printer does not support duplex scanning or the ADF does not support the original document size.
  • When using the ADF, adjust the paper guide on the ADF to the width of the original document.
  • To easily retrieve a document after copying or scanning through the ADF, lift the ADF input tray.
  • When using the scanner glass, close the scanner cover, if possible, to avoid dark edges on the scanned image.
  • When the document to be e-mailed is in place with the settings you want, press to start scanning.
  • Make sure to enter your e ‑ mail account information and set up the SMTP server before sending an e ‑ mail.
  • Add contacts to your address book. When sending an e ‑ mail, you can just select contacts from your address book instead of typing their e ‑ mail addresses repeatedly.
  • Make sure the printer is connected to an Ethernet or wireless network before sending an e ‑ mail.

the SMTP server. If the printer cannot connect to the Internet, then contact your system support

  • Do not load postcards, photos, small items, transparencies, photo paper, or thin media (such as magazine clippings) into the ADF. Place these items on the scanner glass.

The printer supports only one active network connection (Ethernet or wireless) at a time.

2 Click All Programs or Programs, and then select the printer program folder from the list.

Printer Home > select your printer > Settings > Set up the printer to e‑mail

4 Follow the instructions on the computer screen.

Setting up the e-mail function

The E‑mail Setup Wizard opens.

1 From the Finder, navigate to:

Sending e-mail

Tips for e ‑ mailing

or Start.

For Macintosh users

For Windows users

E-mailing

3 Navigate to:

person.

E-mailing 29 · 1 Click

Page 30 of the Lexmark PRO710 user manual — EXT
Page 30 · click to enlarge
Page 30

Setting up the printer to fax 30

2 Remove the protective plug from the port of the printer, and then connect the answering machine

  • You can set the printer to receive faxes automatically (Auto Answer On) or manually (Auto Answer Off).
  • If you want to receive faxes automatically (Auto Answer On), then set the printer to pick up on any number of rings that you want.
Lexmark PRO710 — Setting up the printer to fax diagram (page 30)
Fig. 60 · Setting up the printer to fax

Setup 2: Printer is sharing the line with an answering machine

Connect the cable from the wall jack to the port of the printer.

1 Connect the cable from the wall jack to the port of the printer.

Connected to the same telephone wall jack

to the port.

To connect:

To connect:

cord provided with this product or a UL Listed 26 AWG or larger replacement when connecting

this product or make any electrical or cabling connections, such as the power supply cord or

Check the scenarios below and follow the setup that is applicable to your telephone service.

Step 1: Connect the printer to the telephone line

Setup 1: Printer is connected to a dedicated fax line

this product to the public switched telephone network.

Setting up the printer to fax

Scenario 1: Standard telephone line

telephone, during a lightning storm.

EXT

LINE

Page 31 of the Lexmark PRO710 user manual — EXT
Page 31 · click to enlarge
Page 31

Setting up the printer to fax 31

2 Remove the protective plug from the port of the printer, and then connect the telephone to the

  • This setup works best if you subscribe to a distinctive ring service. If you have distinctive ring service, then make sure that you set the correct ring pattern for the printer. Otherwise, the printer will not
  • If you have only one telephone number on your line, then you need to set the printer to receive faxes manually (Auto Answer Off).
Setup 3Printer is sharing the line with a telephone subscribed to voice mail service
Lexmark PRO710 — Setting up the printer to fax diagram (page 31)
Fig. 61 · Setting up the printer to fax

1 Connect the cable from the wall jack to the port of the printer.

receive faxes even if you have set it to receive faxes automatically.

To connect:

port.

  • If you have only one telephone number on your line, then you need to set the printer to receive faxes automatically (Auto Answer On).
  • Set the printer to pick up calls two rings after the answering machine. For example, if the answering machine picks up calls after four rings, then set the printer to pick up after six rings. This way, the
  • If you subscribe to a distinctive ring service provided by your telephone company, then make sure that you set the correct ring pattern for the printer. Otherwise, the printer will not receive faxes even if

answering machine picks up calls first and your voice calls are received. If the call is a fax, then the

PHONE LINE

Connect the cable from the wall jack to the port of the printer.

printer detects the fax signal on the line and takes over the call.

you have set it to receive faxes automatically.

Connected to different wall jacks

EXT

LINE

To connect:

Page 32 of the Lexmark PRO710 user manual — EXT
Page 32 · click to enlarge
Page 32

Setting up the printer to fax 32

2 Connect a telephone cable from the port on the back of the printer to the phone port on the DSL

3 To continue using a computer for Internet access, connect the computer to the DSL HPN port on the DSL filter.

4 To connect a telephone to the printer, remove the protective plug from the port of the printer

Lexmark PRO710 — Scenario 2: Digital Subscriber Line (DSL) diagram (page 32)
Fig. 62 · Scenario 2: Digital Subscriber Line (DSL)
Lexmark PRO710 — Scenario 2: Digital Subscriber Line (DSL) diagram (page 32)
Fig. 63 · Scenario 2: Digital Subscriber Line (DSL)

1 Connect one end of a telephone cable to the port of the printer.

1 Connect the line port of the DSL filter to the wall jack.

Scenario 3: VoIP telephone service

and then connect the telephone to the port.

To install a filter for the printer:

To connect:

filter.

When you answer the telephone and you hear fax tones, press *9* or the manual answer code on the

  • You can also set the printer to receive faxes automatically (Auto Answer On), but you need to turn off the voice mail service when you are expecting a fax. This setting works best if you are using voice mail

A Digital Subscriber Line splits your regular telephone line into two channels: voice and Internet. Telephone

and fax signals travel through the voice channel, and Internet signals pass through the other channel. This

To minimize interference between the two channels and ensure a quality connection, you need to install

Interference causes noise and static on the telephone, failed and poor quality faxes for the printer, and

way, you can use the same line for analog voice calls (including faxes) and digital Internet access.

a DSL filter for the analog devices (fax machine, telephone, answering machine) in your network.

Scenario 2: Digital Subscriber Line (DSL)

EXT

LINE

slow Internet connection on your computer.

telephone to receive the fax.

more often than fax.

Page 33 of the Lexmark PRO710 user manual — Tips for this setup:
Page 33 · click to enlarge
Page 33

Setting up the printer to fax 33

2 Connect the other end of the cable to the port labeled Phone Line 1 or Phone Port on the cable modem.

3 Remove the protective plug from the port of the printer, and then connect the telephone to the

The port labeled Phone Line 2 or Fax Port is not always active. You may need to pay extra to your

  • To make sure that the phone port on the cable modem is active, plug an analog telephone into the phone port, and then listen for a dial tone. If you hear a dial tone, then the port is active.
Lexmark PRO710 — Scenario 4: Digital telephone service through a cable provider diagram (page 33)
Fig. 64 · Scenario 4: Digital telephone service through a cabl…
Lexmark PRO710 — Scenario 4: Digital telephone service through a cable provider diagram (page 33)
Fig. 65 · Scenario 4: Digital telephone service through a cabl…

Scenario 4: Digital telephone service through a cable provider

Follow this setup if you normally connect your telephone to a cable modem.

1 Connect one end of a telephone cable to the port of the printer.

Setup 1: Printer is connected directly to a cable modem

cable provider if you want to activate the second phone port.

To connect:

port.

2 Connect the other end of the cable to the port labeled Phone Line 1 or Phone Port on the VoIP adapter.

The port labeled Phone Line 2 or Fax Port is not always active. You may need to pay extra to your VoIP

3 Remove the protective plug from the port of the printer, and then connect the telephone to the

  • If you need two phone ports for your devices but do not want to pay extra, then do not plug the printer into the second phone port. You can use a phone splitter. Plug the phone splitter into the Phone Line
  • To make sure that the phone port on the VoIP adapter is active, plug an analog telephone into the phone port, and then listen for a dial tone. If you hear a dial tone, then the port is active.

Make sure you use a phone splitter, not a line splitter. To make sure that you are using the correct

splitter, plug an analog telephone into the splitter and then listen for a dial tone.

1 or Phone Port, and then plug the printer and telephone into the splitter.

provider if you want to activate the second phone port.

Tips for this setup:

port.

Page 34 of the Lexmark PRO710 user manual — the house
Page 34 · click to enlarge
Page 34

Setting up the printer to fax 34

Different countries or regions have different types of telephone wall jacks. The standard wall jack adopted

The fax ports on the back of the printer and the telephone cable that comes with the printer have RJ‑11

connectors. If you have a different type of connector in your country or region, then you may need to use

by most countries or regions is the Registered Jack-11 (RJ-11). You need to have an RJ‑11 plug, or a

telephone cable that has an RJ‑11 connector, so you can connect a device to an RJ‑11 wall jack.

Scenario 5: Country ‑ or region ‑ specific setup

an RJ‑11 adapter.

  • If you need two phone ports for your devices but do not want to pay extra, then do not plug the printer into the second phone port. You can use a phone splitter. Plug the phone splitter into the Phone Line

Follow this setup if your cable provider activated the wall jacks in your house so that you do not have to

2 Remove the protective plug from the port of the printer, and then connect the telephone to the

Make sure you use a phone splitter, not a line splitter. To make sure that you are using the correct

Setup 2Printer is connected to a wall jack; cable modem is installed elsewhere in

plug your devices into the cable modem. Your cable telephone service comes from the wall jacks.

splitter, plug an analog telephone into the splitter and then listen for a dial tone.

1 or Phone Port , and then plug the printer and telephone into the splitter.

1 Connect the cable from the wall jack to the port of the printer.

the house

To connect:

port.

Page 35 of the Lexmark PRO710 user manual — EXT
Page 35 · click to enlarge
Page 35

Setting up the printer to fax 35

If the additional device (telephone or answering machine) has an RJ-11 connector, then you can remove

In some countries or regions, you need to plug all devices into the wall jack. You cannot plug a telephone

Lexmark PRO710 — Scenario 5: Countryor region-specific setup diagram (page 35)
Fig. 66 · Scenario 5: Countryor region-specific setup
Lexmark PRO710 — Scenario 5: Countryor region-specific setup diagram (page 35)
Fig. 67 · Scenario 5: Countryor region-specific setup

Connecting the printer in countries or regions that use serial connection

or answering machine into the port of the printer. This is called serial connection.

  • The printer may not come with an RJ-11 adapter in your country or region.
  • Do not remove the wrap plug from the port of the printer.

the wrap plug and connect the device to the port of the printer.

2 Connect the other end of the cable to the RJ‑11 adapter, and then connect the adapter to the wall jack.

3 If you want to connect another device (telephone or answering machine) to the same wall jack, and if the device has a non‑RJ 11 connector, then connect it directly to the wall jack.

Lexmark PRO710 — Connecting the printer in countries or regions that use serial connection diagram (page 35)
Fig. 68 · Connecting the printer in countries or regions that…

1 Connect one end of a telephone cable to the port of the printer.

Connecting the printer to a non‑RJ‑11 wall jack

EXT

LINE

To connect:

Austria Germany Portugal · Denmark Italy Sweden · Belgium Ireland Spain

Page 36 of the Lexmark PRO710 user manual — EXT
Page 36 · click to enlarge
Page 36

Setting up the printer to fax 36

The German wall jack has two kinds of ports. The N ports are for fax machines, modems, and answering

Lexmark PRO710 — Scenario 5: Countryor region-specific setup diagram (page 36)
Fig. 69 · Scenario 5: Countryor region-specific setup

Connecting the printer to a wall jack in Germany

machines. The F port is for telephones.

from the port of the printer. It is necessary for the proper functioning of the devices on the

Lexmark PRO710 — Connecting the printer to a wall jack in Germany diagram (page 36)
Fig. 70 · Connecting the printer to a wall jack in Germany

Finland Norway United Kingdom

Connect the cable from the wall jack to the port of the printer.

EXT

LINE

telephone line.

To connect:

France Netherlands Switzerland

Page 37 of the Lexmark PRO710 user manual — EXT
Page 37 · click to enlarge
Page 37

Setting up the printer to fax 37

1 While the printer is connected to a telephone line through the port on the back of the printer, plug

Your user information includes your name or your company name, your fax number (your fax number is

your telephone number, unless you have a dedicated fax telephone line), and the time and date on your

fax machine when a transmission is made. This information appears in the header and footer of the faxes

If the printer is connected to a dedicated fax line or sharing the line with an answering machine, then you

In some countries, you cannot send a fax without this information. Some fax machines also block faxes

If you do not hear a dial tone, then review Step 1 or see the “Fax troubleshooting checklist” on page

can set the printer to receive faxes automatically. If the printer is sharing the line with a telephone

Step 4: Set the printer to receive faxes automatically or

without sender information, so make sure that you enter this information in your printer.

> Setup > > Fax Setup > > Ringing and Answering > > Auto Answer >

If you hear a dial tone, then the printer is properly connected to the telephone line.

> Setup > > Fax Setup > > Dialing and Sending > > Fax Name >

If you hear a dial tone, then the telephone line and the wall jack are working.

Make sure the printer is properly connected to the telephone line

2 Press the arrow buttons to scroll to the setting you want, and then press .

subscribed to voice mail service, then set the printer to receive faxes manually.

Step 3: Set your fax name and fax number

3 Press the arrow buttons to scroll to Fax Number, and then press .

4 Enter your fax number or your telephone number, and then press .

2 Enter your name or your company name, and then press .

  • To change a character, press the left arrow button.
  • To add a space, press the number 0.

an analog telephone into the port of the printer.

1 From the printer control panel, navigate to:

1 From the printer control panel, navigate to:

2 Listen for a dial tone.

manually

that you send.

2 Connect the other end of the cable to the RJ‑11 adapter, and then connect the adapter to an N port.

3 If you want to connect a telephone and answering machine to the same wall jack, then connect the devices as shown.

A dial tone lets you know if the telephone line is working or if the printer is properly connected to the

PHONE LINE

Make sure the telephone line and the wall jack are working

1 Connect one end of a telephone cable to the port of the printer.

N F N

2 Listen for a dial tone through the telephone handset.

Step 2: Check the dial tone

1 Plug an analog telephone into the wall jack.

Connect the printer to any of the N ports.

EXT

LINE

telephone line.

To connect:

Page 38 of the Lexmark PRO710 user manual — Using the printer control panel
Page 38 · click to enlarge
Page 38

Setting up the printer to fax 38

If you are connecting the printer to a computer, then you can also create a contact list using the fax

2 Click All Programs or Programs, and then select the printer program folder from the list.

Enter the entry number before entering the contact name and fax number of the contact.

Printer Home > select your printer > Fax > Edit contact list

?.

The Contacts tab of the Printer Setup Utility opens.

For more information on the fax software, click Help or

  • 3 Click the Contacts tab.
  • To add contacts, click the Individuals tab.
  • To add fax groups, click the Groups tab.

Applications > select your printer folder

Using the fax software

1 From the Finder, navigate to:

2 Double‑click Printer Settings.

or Start.

For Macintosh users

For Windows users

3 Navigate to:

software.

If you set Auto Answer to On in Step 4, then do the following. If you set Auto Answer to Off, then proceed

feature offered by telephone companies. This feature allows you to have multiple telephone numbers on

Triple Rings Only). The different ring patterns let you know which telephone number was dialed and which

Assign one of your telephone numbers to the printer as the fax number, and then set the printer to answer

the ring pattern of that number. If the pattern is set incorrectly, then the printer rings, but it never receives

If the printer is sharing the line with other devices, then set the printer to pick up on the greater number

of rings. If the printer is connected to a dedicated fax line, then you can choose any number of rings that

Setting the correct ring is important if you subscribe to the Distinctive Ring Pattern Detection (DPRD)

one telephone line. Each telephone number has a designated ring pattern (All Rings, Single Ring Only,

Double Ring Only, Triple Ring Only, Single or Double Rings Only, Single or Triple Rings Only, Double or

  • 2 Use the menus to add a contact or a fax group. You can add up to 89 contacts and 10 fax groups.
  • To change a character, press the left arrow button.
  • To add a space, press the number 0.

> Setup > > Fax Setup > > Ringing and Answering > > Ring Pattern >

2 Press the arrow buttons to scroll to the ring pattern you want, and then press .

> Setup > > Fax Setup > > Ringing and Answering > > Pick Up On >

> Address Book > Setup > > Fax Setup > > Address Book >

2 Select the number of rings that you want, and then save the setting.

Step 5: Set the number of rings

If you do not subscribe to Distinctive Ring

Touch‑screen models Arrow‑button models

1 From the printer control panel, navigate to:

1 From the printer control panel, navigate to:

Step 6: Create a contact list

1 From the printer control panel, navigate to:

If you subscribe to Distinctive Ring

device you should use to answer the call.

Using the printer control panel

to Step 6.

you want.

the fax.

1 Click

Page 39 of the Lexmark PRO710 user manual — Tip:
Page 39 · click to enlarge
Page 39
  • Make sure that the printer is on and connected to a working telephone, DSL, or VoIP line. The line is working if you hear a dial tone.

2 Make sure the appropriate printer is selected, and then click Properties, Preferences, Options, or Setup.

7 Select Include Cover Page with Fax, and enter the appropriate information if you want to include a cover page with the fax.

  • If you have set the printer to receive faxes automatically (Auto Answer On), then load paper in the printer.
  • If you set the printer to receive faxes manually (Auto Answer Off), then make sure that the ringer volume is not set to Off.

printer. If the fax version of the printer is not on the list, then choose Add a printer, and then

You can enter fax numbers manually or by using the Phone Book feature.

4 Enter the recipient fax number or numbers in the “Fax number(s)” field.

2 From the Printer pop‑up menu, select the fax version of your printer.

3 Click the Fax tab, and then make sure Enable Fax is selected.

6 Select the appropriate paper size and page orientation.

5 If necessary, enter a prefix in the Dialing Prefix dialog.

Sending faxes using the computer

3 Enter the name and number of the recipient.

1 With a document open, choose File > Print.

1 With a document open, click File > Print.

choose the fax version of the printer.

Tips for receiving faxes

Receiving faxes

For Macintosh users

For Windows users

When receiving faxes:

8 Click OK.

4 Click Fax.

this product or make any electrical or cabling connections, such as the fax feature, power cord, or

  • Make sure the printer is on and connected to a working telephone, DSL, or VoIP line. The line is working if you hear a dial tone.
  • Make sure the paper exit tray is fully extended and the tray extension is flipped out.
  • Depending on your printer model, use the ADF when scanning two ‑ sided (duplex) pages.
  • To easily retrieve a document after copying or scanning, lift the ADF input tray.
  • When using the ADF, adjust the paper guide on the ADF to the width of the original document.
  • When using the scanner glass, close the scanner cover, if possible, to avoid dark edges on the scanned image.

2 Enter a fax number, or press Address Book to select a number from the Speed Dial or Group Dial list.

  • When the document to be faxed is in place with the settings you want, press to send the fax.

If you want to send a fax to a group of numbers (broadcast fax), then press the left or right arrow

  • Do not load postcards, photos, small items, transparencies, photo paper, or thin media (such as magazine clippings) into the ADF. Place these items on the scanner glass.

button to enter another number, and then press . Repeat this step to add more numbers.

4 Press the Color/Black button to select a color or black‑and‑white fax.

3 If you want to send a fax to a single recipient, then press .

Sending faxes using the printer control panel

  • You can send a broadcast fax to up to 30 recipients.

1 From the printer control panel, navigate to:

telephone, during a lightning storm.

5 Press to start the fax job.

Tips for sending faxes

Sending faxes

Faxing

fax.

Tip:

Faxing 39 · > Fax

Page 40 of the Lexmark PRO710 user manual — Tips:
Page 40 · click to enlarge
Page 40
  • Make sure that the telephone is plugged into the port on the back of the printer and that the

printer is connected to the wall jack through the port.

b Press the arrow buttons to scroll to the number of rings that you want, and then press to save

printer detects the fax signal on the line and takes over the call. If the printer is on a dedicated fax line,

  • If you have multiple numbers on a single line, or if you subscribe to a distinctive ring service provided by your telephone company, then make sure that you set the correct ring pattern for the printer.
  • The default code for answering faxes manually is *9*, but for increased security, you can change it to a number that only you know. You can enter up to 7 characters for your code. The valid characters are

When the number of rings you set is detected, the printer automatically receives the incoming fax.

  • If the printer is sharing the line with other analog devices (telephone, answering machine), then set the printer to pick up calls two rings after the answering machine. For example, if the answering

answering machine picks up calls first and your voice calls are received. If the call is a fax, then the

> Setup > > Fax Setup > > Ringing and Answering > > Auto Answer > > Off >

> Setup > > Fax Setup > > Ringing and Answering > > Auto Answer > > On >

machine picks up calls after four rings, then set the printer to pick up after six rings. This way, the

Otherwise, the printer will not receive faxes even if you have set it to receive faxes automatically.

2 When the telephone rings and you hear fax tones when you pick up the handset, press on the

a Press the arrow buttons to scroll to Pick Up On, and then press .

2 Set the number of rings before the printer picks up incoming faxes:

then you may set the printer to pick up on any number of rings.

printer or *9* on the telephone attached to the printer.

From the printer control panel, navigate to:

From the printer control panel, navigate to:

the digits 0–9 and the characters # and *.

Receiving faxes automatically

1 Make sure that Auto Answer is on:

Receiving faxes manually

1 Turn off Auto Answer:

the setting.

a fax.

Tips:

a fax.

Tips:

Faxing 40

Page 41 of the Lexmark PRO710 user manual — wireless network
Page 41 · click to enlarge
Page 41

3 Double-click the software installer package, and then follow the instructions on the computer screen.

Wi‑Fi Protected Setup (WPS) is a simple and secure configuration that allows you to establish a wireless

home network and enable network security without requiring prior knowledge of Wi‑Fi technology. It is

no longer necessary to configure the network name (SSID) and WEP key or WPA passphrase for network

  • Personal Identification Number (PIN)—A PIN on the printer is entered into the wireless settings of the access point.
  • Push Button Configuration (PBC)—Buttons on both the printer and the access point are pushed within a given period of time.

b In the Start Search or Run box, type D:\setup.exe, where D is the letter of your CD or DVD

If the installation dialog does not appear after a minute, then click the CD icon on the desktop.

If the installation dialog does not appear after a minute, then launch the CD manually:

Look for any of these identifier marks to check if your access point is WPS certified:

The printer supports the following methods in connecting to a wireless network:

What is Wi ‑ Fi Protected Setup?

, or click Start and then click Run.

3 Follow the instructions on the computer screen.

1 Close all open software programs.

2 Insert the installation software CD.

2 Insert the installation software CD.

c Press Enter, or click OK.

1 Close all open applications.

For Macintosh users

For Windows users

drive.

devices.

To find the WPA/WPA2 passphrase for the wireless network, see the documentation that came with

the access point, see the Web page associated with the access point, or consult your system support

  • Your wireless network is set up and working properly.
  • The computer you are using is connected to the same wireless network where you want to set up the printer.

wireless utility of the computer network adapter and look for the network name. If you cannot find the

  • Hexadecimal characters are A–F, a–f, and 0–9.
  • ASCII characters are letters, numbers, and symbols found on a keyboard. ASCII characters in a WPA/WPA2 passphrase are case ‑ sensitive.

SSID or the security information for your network, then see the documentation that came with the

If your access point is using WPA or WPA2 security, then the WPA/WPA2 passphrase should be:

  • The name of your wireless network, which is also known as the SSID (Service Set Identifier)
  • If encryption was used to secure your network
  • The security key (either a WEP key or WPA/WPA2 passphrase)

Information you will need to set up the printer on a

If your wireless network is not using security, then you will not have a security key.

Installing the printer on a wireless network

If your access point is using WEP security, then the WEP key should be:

Before you install the printer on a wireless network, make sure that:

To set up the printer for wireless printing, you need to know:

access point, or contact your system support person.

  • Exactly 10 or 26 hexadecimal characters

Wireless networking

  • Exactly 64 hexadecimal characters
  • Exactly 5 or 13 ASCII characters
  • From 8 to 63 ASCII characters

wireless network

person.

Show 4 more labels / short text on this page
Wireless networking 41 · a Click · or · or
Page 42 of the Lexmark PRO710 user manual — Configuring Wi ‑ Fi Protected Setup manually
Page 42 · click to enlarge
Page 42

For more information on accessing the wireless settings and determining the WPS capability of your access

it using WPS, then push the WPS button on the wireless router. Wait for the printer control panel to display

a message to begin WPS configuration. There might be a short delay before the message appears. If nothing

point, see the documentation that came with the access point or contact your system support person.

If your printer or device has not yet been configured for wireless connection and you want to configure

> Setup > > Network Setup > > Wireless 802.11b/g/n > > Network Connection

> Setup > > Network Setup > > Wireless 802.11b/g/n > > Network Connection

Setup > > Wireless > > Wi‑Fi Protected Setup > > WPS PBC Mode >

Setup > > Wireless > > Wi‑Fi Protected Setup > > WPS PIN Mode >

U SE THE P ERSONAL I DENTIFICATION N UMBER (PIN) METHOD

You can find these WPS logos on the side, back, or top of your access point.

Configuring Wi ‑ Fi Protected Setup manually

U SE THE P USH B UTTON C ONFIGURATION (PBC) METHOD

happens after 30 seconds, then do one of the following:

2 Follow the instructions on the printer display.

2 Follow the instructions on the printer display.

1 From the printer control panel, navigate to:

1 From the printer control panel, navigate to:

information, see the User’s Guide.

Wireless networking 42

Page 43 of the Lexmark PRO710 user manual — Before you troubleshoot
Page 43 · click to enlarge
Page 43

If you encountered problems while installing, or if your printer does not appear in the list in the printers

folder or as a printer option when sending a print job, then try uninstalling and reinstalling the software.

3 To confirm the setting, press the left or right arrow button to scroll to Yes, and then press .

2 In the Start Search or Run box, type D:\setup.exe, where D is the letter of your CD or DVD drive.

2 Double-click the software installer package, and then follow the instructions on the computer screen.

T EMPORARILY DISABLE SECURITY PROGRAMS IN W INDOWS BEFORE INSTALLING THE SOFTWARE

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the

2 Press the up or down arrow button to scroll to the language you want, and then press .

If the "Before you troubleshoot" checklist does not solve the problem, then try the following:

M AKE SURE THAT YOUR COMPUTER MEETS THE MINIMUM SYSTEM REQUIREMENTS

4 Click Install, and then follow the instructions on the computer screen.

Installation screen did not appear during installation

> Setup > > Device Setup > > Language >

Incorrect language appears on the display

C HANGE THE LANGUAGE USING THE PRINTER MENUS

1 From the printer control panel, navigate to:

, or click Start and then click Run.

1 From the Finder desktop, click the CD icon.

Before you reinstall the software, do the following:

L AUNCH THE PRINTER CD MANUALLY

Software did not install

3 Press Enter, or click OK.

following:

  • Make sure the power cord is plugged into the printer and into a properly grounded, working electrical outlet.
  • Make sure the printer is turned on.
  • Make sure the printer is securely connected to the computer, print server, or network access point.
  • Check the printer for error messages, and resolve any errors.
  • Check for paper jam messages, and clear any jams.
  • Check the ink cartridges, and install new cartridges if necessary.
  • Turn the printer off, wait about 10 seconds, and then turn the printer back on.
  • Knowledgebase articles with the latest information and troubleshooting for your printer
  • Live online technical support
  • Contact numbers for telephone technical support

If Troubleshooting does not solve your problem

Visit our Web site at http://support.lexmark.com to find the following:

  • “Incorrect language appears on the display” on page 43
  • “Software did not install” on page 43
  • “Print job does not print or is missing pages” on page 44
  • “Printer is printing blank pages” on page 44
  • “Printer is busy or does not respond” on page 45
  • “Cannot delete documents from the print queue” on page 45
  • “Cannot print through USB” on page 45

Use this checklist to solve most printer problems:

Before you troubleshoot

Setup troubleshooting

Troubleshooting

the printer.

Show 4 more labels / short text on this page
Troubleshooting 43 · For Macintosh users · For Windows users · 1 Click
Page 44 of the Lexmark PRO710 user manual — R ECONNECT THE PRINTER POWER SUPPLY
Page 44 · click to enlarge
Page 44

3 After one minute, reconnect the power cord into the power supply, and then plug the power cord into the wall outlet.

2 Unplug the power cord from the wall outlet, and then pull out the power cord from the power supply.

1 Reinstall the ink cartridges, see “Replacing ink cartridges” on page 16 for more information.

1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.

  • For a USB-connected printer, remove and then reconnect the USB cable.
  • For a printer that is wirelessly connected, see the Wireless troubleshooting section.

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.

R EINSTALL THE INK CARTRIDGES AND DEEP CLEAN AND ALIGN THE PRINTHEAD

If your printer does not appear in the list, then try either of the following:

R EMOVE AND RECONNECT THE USB CABLE CONNECTED TO YOUR PRINTER

2 Firmly plug the square end of the USB cable into the back of the printer.

Blank pages may be caused by improperly installed ink cartridges.

M AKE SURE YOUR PRINTER IS SET AS THE DEFAULT PRINTER

R EMOVE AND REINSTALL THE PRINTER SOFTWARE

M AKE SURE THE PRINT JOB IS NOT PAUSED

The USB port is marked with .

R ECONNECT THE PRINTER POWER SUPPLY

Printer is printing blank pages

C HECK THE USB CONNECTION

connected to a defective port.

1 Turn off the printer.

4 Turn on the printer.

the printer.

3 After one minute, reconnect the power cord into the power supply, and then plug the power cord into the wall outlet.

If your printer does not appear in the Printer list, then choose Add Printer. From the list of printers

2 Unplug the power cord from the wall outlet, and then pull out the power cord from the power supply.

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the

1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.

SELECT YOUR PRINTER FROM THE PRINT DIALOG BEFORE SENDING THE PRINT JOB

The cartridges should click firmly into the matching color slot of the printhead.

2 Firmly plug the square end of the USB cable into the back of the printer.

2 From the printer pop-up menu, choose your printer, and then click Print.

in the Default tab, select your printer, and then click Add.

M AKE SURE THE INK CARTRIDGES ARE INSERTED CORRECTLY

Print job does not print or is missing pages

1 Turn the printer on, and then open the printer.

2 Make sure the cartridges are inserted correctly.

1 With a document open, choose File > Print.

The USB port is marked with .

R ECONNECT THE PRINTER POWER SUPPLY

C HECK THE USB CONNECTION

connected to a defective port.

1 Turn off the printer.

4 Turn on the printer.

3 Close the printer.

the printer.

following:

Troubleshooting 44

Page 45 of the Lexmark PRO710 user manual — R ECONNECT THE PRINTER POWER SUPPLY
Page 45 · click to enlarge
Page 45

If you have jobs stuck in the print queue and cannot delete them to get other jobs to print, then the

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the

1 Check the USB cable for any obvious damage. If the cable is damaged, then use a new one.

3 Firmly plug the rectangular end of the USB cable into the USB port of the computer.

If USB Host Controller and USB Root Hub are listed, then the USB port is enabled.

R EMOVE AND RECONNECT THE USB CABLE CONNECTED TO YOUR PRINTER

2 Firmly plug the square end of the USB cable into the back of the printer.

Cannot delete documents from the print queue

4 Click the plus sign (+) beside Universal Serial Bus controllers.

For more information, see the computer documentation.

M AKE SURE THE USB PORT IS ENABLED IN W INDOWS

2 In the Start Search or Run box, type devmgmt.msc.

R EMOVE AND REINSTALL THE PRINTER SOFTWARE

computer and printer may not be communicating.

, or click Start and then click Run.

  • “Fax troubleshooting checklist” on page 46
  • “Cannot send faxes” on page 46

The USB port is marked with .

R ESTART THE COMPUTER AND TRY AGAIN

Cannot print through USB

The Device Manager opens.

Fax troubleshooting

C HECK THE USB CONNECTION

connected to a defective port.

3 Press Enter, or click OK.

following:

If the cartridges do not seem to fit, then make sure the printhead is properly seated, and then try

4 Press the up or down arrow button to scroll to Deep Clean Printhead, and then press .

If the power light is blinking on and off slowly, then the printer is in Sleep mode. Press to wake up

3 After one minute, reconnect the power cord into the power supply, and then plug the power cord into the wall outlet.

If this problem persists, then check our Web site for updates for your printer software or firmware.

2 Unplug the power cord from the wall outlet, and then pull out the power cord from the power supply.

6 From the Maintenance menu screen, press the up or down arrow button to scroll to Align

If the "Before you troubleshoot" checklist does not solve the problem, then try one or more of the

1 Unplug the power cord from the wall outlet, and then wait 10 seconds.

2 Insert the power cord into the wall outlet, and then turn on the printer.

If the printer will not come out of Sleep mode, then reset the power:

M AKE SURE THE PRINTER IS NOT IN S LEEP MODE

3 From the printer control panel, navigate to:

Printer is busy or does not respond

> Setup > > Maintenance >

R ECONNECT THE PRINTER POWER SUPPLY

Printer, and then press .

installing the cartridges again.

2 Load plain, unmarked paper.

5 Load plain, unmarked paper.

An alignment page prints.

A cleaning page prints.

1 Turn off the printer.

4 Turn on the printer.

the printer.

the printer.

following:

Troubleshooting 45 · 1 Click

Page 46 of the Lexmark PRO710 user manual — Connection checklist
Page 46 · click to enlarge
Page 46

transmission capability. The speed of the modem of the receiving fax machine must match or be greater

Errors and blurs may appear in the faxed document if there is too much noise on the line. This option

enables the printer to transmit the bad blocks of data again and correct the errors. When a fax has too

The dialing prefix is the number or series of numbers that you press before you can dial the actual fax

number or telephone number. If the printer is in an office setting or in a private branch exchange, this

The modem of the printer can transmit data at 33,600 bps. This is the maximum speed at which the

If the receiving fax machine does not support color fax, then this option automatically converts the

printer can send and receive faxes. It is not necessary, however, to set the modem to its fastest

outgoing color fax to black and white. It also automatically reduces the resolution of the fax to a

> Setup > > Fax Setup > > Dialing and Sending > > Auto Fax Convert >

than the speed at which you are sending your fax. Otherwise, your fax will not be received.

> Setup > > Fax Setup > > Dialing and Sending > > Max Send Speed >

> Setup > > Fax Setup > > Dialing and Sending > > Error Correction >

can be a specific number that you need to press so you can make a call outside the office.

If it is not set to On, then press the arrow buttons to select On, and then press .

If it is not set to On, then press the arrow buttons to select On, and then press .

> Setup > > Fax Setup > > Dialing and Sending > > Dial Prefix >

Make sure that the dial prefix entered in the printer is correct for your network.

many errors, the fax may be rejected by the receiving fax machine.

D ECREASE THE TRANSMISSION SPEED OF THE FAX MODEM

M AKE SURE THAT THE D IAL P REFIX SETTING IS CORRECT

2 Press the arrow buttons to create or modify the prefix.

2 Check to see if automatic fax conversion is set to On.

resolution that the receiving machine can support.

1 From the printer control panel, navigate to:

2 Select a sending speed, and then press .

1 From the printer control panel, navigate to:

2 Check to see if error correction is set to On.

1 From the printer control panel, navigate to:

1 From the printer control panel, navigate to:

E NABLE AUTOMATIC FAX CONVERSION

E NABLE ERROR CORRECTION

If you do not hear a dial tone, then use the checklist below. Listen for a dial tone after checking each

  • If the printer is connected to a VoIP adapter or cable modem, then make sure that the printer is plugged into the first phone port.
  • If you are using a splitter, then make sure that you are using a phone splitter. Do not use a line splitter.

If the “Fax troubleshooting checklist” does not solve the problem, then try one or more of the following:

If you did not enter your user information during initial setup, then enter your fax name and fax number.

In some countries, you cannot send a fax without entering your fax name or company name. Some fax

1 Check for a dial tone on the telephone line by plugging an analog telephone into the wall jack, DSL filter, VoIP device, or cable modem where you connected the printer. Make sure you plug the

If you hear a dial tone but still have problems sending and receiving faxes, then see the other topics

  • If the printer is connected to a Digital Subscriber Line, then make sure you are using a DSL filter for the printer.
  • Make sure that the printer and other devices on the line (if applicable) are set up and configured correctly according to your setup scenario.

2 While the printer is connected to the telephone line, check for a dial tone by plugging an analog

MAKE SURE THAT YOU HAVE REGISTERED YOUR USER INFORMATION IN THE PRINTER

If you encounter problems sending and receiving faxes, then check the connection first:

machines also block unknown faxes or faxes without sender information.

Check the cable connections for the following hardware, if applicable:

Telephone VoIP adapter DSL filter RJ‑11 adapter

If you do not hear a dial tone, then contact your line provider.

  • Make sure that the cables are connected to the correct ports.
  • Make sure that the cables are securely plugged in.

Power supply Answering machine Cable modem Splitter

telephone into the port of the printer.

  • “Cannot receive faxes” on page 47
  • “Cannot run the fax software” on page 47

Fax troubleshooting checklist

telephone into the same port.

Cannot send faxes

Connection checklist

in this section.

item.

Troubleshooting 46

Page 47 of the Lexmark PRO710 user manual — I NCREASE THE RINGER VOLUME
Page 47 · click to enlarge
Page 47

If you set the printer to receive faxes manually (Auto Answer Off), then you need to press the correct

The printer must be connected to a telephone, DSL, VoIP, or cable service before you can configure the

VoIP adapter, or a cable modem) before you can open the fax software and configure the fax settings.

If you are having trouble setting up your printer on a network, print a network setup page, and then see

more information on the location of the network indicator lights, see“Using the printer control panel” on

You need to connect the printer to your telephone line (through a standard wall jack, a DSL filter, a

Also, make sure to check the network indicator lights to verify the connection status of the printer. For

  • The printer, the computer, and the access point (wireless router) are all plugged in and turned on.
  • The wireless network is working properly.

If your network has Internet access, then try connecting to the Internet over a wireless connection.

> Setup > > Fax Setup > > Ringing and Answering > > Manual Pickup Code >

know. You can enter up to 7 characters for your code. The valid characters are the digits 0–9 and the

The fax option is available for use only with the PostScript driver or the Universal Fax Driver. For

information on installing these drivers, see the Software and Documentation CD.

Before beginning to troubleshoot the wireless printer, verify the following:

M AKE SURE THAT YOU HAVE THE CORRECT MANUAL ANSWER CODE

M AKE SURE THE PRINTER IS CONNECTED TO A TELEPHONE LINE

2 Copy the manual answer code that appears on the display.

code when a fax comes in so that the printer can receive it.

Try accessing other computers on your wireless network.

Wireless network troubleshooting

the User's Guide available on the installation software CD.

1 From the printer control panel, navigate to:

Wireless troubleshooting checklist

M AKE SURE A FAX DRIVER IS INSTALLED

Cannot run the fax software

fax settings in the fax software.

  • Your SSID is correct.

characters # and *.

page 13.

If the “Fax troubleshooting checklist” does not solve the problem, then try one or more of the following:

The fax settings depend on whether the printer is connected to its own fax line or shares the line with

If the printer is sharing the telephone line with an answering machine, then make sure that the following

If the printer is sharing the telephone line with a telephone subscribed to voice mail, then make sure

The printer saves an incoming fax to the printer memory before it prints the fax. If the printer runs out

later. However, if the printer memory is full, then the printer may not be able to receive more incoming

faxes. An error message appears on the display when the printer memory is full. Resolve the error to

  • Auto Answer is On.
  • The printer picks up on a greater number of rings than the answering machine.
  • The printer picks up on the correct distinctive ring (if you subscribe to a distinctive ring service).
  • Auto Answer is Off (if you have only one number on the telephone line).
  • The printer picks up on the correct distinctive ring (if you subscribe to a distinctive ring service).

connected to an analog port on the PBX. You may need a digital line converter that converts digital

If you set the printer to receive faxes manually (Auto Answer Off), then increase the ringer volume.

of ink or runs out of paper while receiving the fax, then the printer saves the fax so you can print it

The printer is an analog device. If you are using a PBX system, then make sure that the printer is

> Setup > > Fax Setup > > Ringing and Answering > > Fax Forward >

MAKE SURE THAT YOU HAVE CONFIGURED THE CORRECT SETTINGS FOR YOUR SETUP

3 If the prefix is not correct, enter the correct prefix, and then press .

M AKE SURE THAT THE PRINTER IS CONNECTED TO AN ANALOG PORT

2 Press the arrow buttons to scroll to Off, and then press .

M AKE SURE THAT THE PRINTER MEMORY IS NOT FULL

M AKE SURE THAT F AX F ORWARDING IS DISABLED

1 From the printer control panel, navigate to:

free up space in the printer memory.

I NCREASE THE RINGER VOLUME

Cannot receive faxes

that the following are set:

signals into analog signals.

other devices.

are set:

Troubleshooting 47

Page 48 of the Lexmark PRO710 user manual — For Windows users
Page 48 · click to enlarge
Page 48

If you encountered problems while installing, or if your printer does not appear in the printers folder or

When you are connected to another network through a VPN connection, you will not be able to access

  • Exactly 5 or 13 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard. ASCII characters in a WEP key are case ‑ sensitive.

Wait one minute for the printer and computer to reestablish the connection. This can sometimes

  • You can locate the printer IP address by viewing the printer network setup page. See the User's Guide on the software installation CD for more information on printing a network setup page.

Before you reinstall the software, check the troubleshooting checklist, and then do the following:

as a printer option when sending a print job, then try uninstalling and reinstalling the software.

  • Exactly 10 or 26 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.

4 If you are connected over a wireless network, choose AirPort from the Active Services list.

the printer over your wireless network. End your VPN session, and then try printing again.

If your access point is using WPA or WPA2 security, then the WPA passphrase should be:

  • Exactly 64 hexadecimal characters. Hexadecimal characters are A–F, a–f, and 0–9.

TURN THE ACCESS POINT (WIRELESS ROUTER) OFF AND THEN BACK ON

Select printer features are not available when Demo Mode is turned on.

If your access point is using WEP security, then the WEP key should be:

refresh network connections and resolve connectivity issues.

1 From the Apple menu, choose About This Mac.

Cannot print over wireless network

> Setup > > Demo Mode > > Off >

C HECK YOUR WEP KEY OR WPA PASSPHRASE

3 From the Contents pane, choose Network.

From the printer control panel, navigate to:

M AKE SURE D EMO M ODE IS TURNED OFF

D ISCONNECT FROM VPN SESSION

Locating the printer IP address

For Macintosh users

2 Click More Info.

A security key is like a password. All devices on the same wireless network using WEP, WPA, or WPA2

For most networks, the printer and the computer should be within 100 feet (30 meters) of the access

  • The Wi ‑ Fi indicator is green and successfully connected.
  • The printer driver is installed on the computer from which you are performing a task.
  • The correct printer port is selected.
  • The computer and printer are both connected to the same wireless network.
  • The printer is located away from obstacles or electronic devices that could interfere with the wireless signal.

Many devices can interfere with the wireless signal, including baby monitors, motors, cordless phones,

A network setup page lists the configuration settings of the printer, including the IP address and MAC

Make sure the printer and access point are not separated by poles, walls, or support columns

The IP address appears as four sets of numbers separated by periods, such as 192.168.0.100.

If you are not sure if your security information is correct, then run the wireless setup again.

security system cameras, other wireless networks, and some Bluetooth devices.

If you are not sure if your SSID is correct, then run the wireless setup again.

  • The printer and the computer are within the range of the wireless network.

> Setup > > Network Setup > > Print Network Setup Page >

  • Your WEP key or WPA passphrase is correct (if your network is secure).

Print a network setup page to verify the SSID the printer is using.

Log on to the access point and check the security settings.

2 From the printer control panel, navigate to:

, or click Start and then click Run.

2 In the Start Search or Run box, type cmd.

Printing a network setup page

4 Type ipconfig, and then press Enter.

The Command Prompt window opens.

share the same security key.

containing metal or concrete.

Locating IP addresses

3 Press Enter, or click OK.

point (wireless router).

address of the printer.

1 Load plain paper.

For Windows users

Show 4 more labels / short text on this page
Troubleshooting 48 · or · or · 1 Click
Page 49 of the Lexmark PRO710 user manual — C HECK THE WIRELESS SIGNAL QUALITY
Page 49 · click to enlarge
Page 49

If the printer is not on the same wireless network as the computer, then you will not be able to print

  • 2 In the Start Search or Run box, type cmd . 3 Press Enter or click OK . 4 Type ipconfig , and then press Enter . Check the Wireless Network Connection section:
  • The “Default Gateway” entry is typically the access point .
  • The IP address appears as four sets of numbers separated by periods, such as 192.168.2.134. b Type the user name and password of the access point when prompted.

If the SSIDs are the same, then the computer and the printer are connected to the same wireless

If the SSIDs are not the same, then run the utility again to set up the printer on the wireless network

The SSID of the network that the computer is connected to is displayed in the Network Name menu.

wirelessly. The SSID of the printer must match the SSID of the computer, if the computer is already

MAKE SURE THAT YOUR COMPUTER AND PRINTER ARE CONNECTED TO THE SAME WIRELESS

1 Obtain the SSID of the network that the computer is connected to. a Type the IP address of your access point into the address field of your Web browser.

2 Obtain the SSID of the network that the printer is connected to: a From the printer, print a network setup page.

3 Compare the SSID of the computer and SSID of the printer.

If you do not know the IP address of the access point:

d In the Wireless settings section, look for the SSID.

, or click Start and then click Run.

For Macintosh users with an AirPort base station

b In the Wireless section, look for SSID.

System Preferences > Network > AirPort

1 From the Apple menu, navigate to:

connected to the wireless network.

In Mac OS X version 10.5 or later

e Write down the SSID.

used by the computer.

2 Write down the SSID.

For Windows users

c Click OK.

network.

NETWORK

Wireless broadband boxes in Europe, the Middle East, and Africa such as LiveBox, AliceBox, N9UF Box,

FreeBox, or Club Internet may require you to press an association/registration button when adding the

If you are using one of these boxes and need more information, then see the documentation that came

appliances, cordless phones, baby monitors, and security system cameras. Make sure your access point

Print a network setup page and check the signal quality. If the signal quality is listed as good or excellent,

  • If you set the access point to issue a limited number of IP addresses, then you must change this so that the printer can be added.
  • If you are using MAC (Media Access Control) address filtering to limit access to your wireless network, then you must add the printer MAC address to the list of addresses allowed to connect
  • See if you have access to the Internet by opening your Web browser and accessing any site.
  • If there are other computers or resources on your wireless network, then check to see if you can access them from your computer.

The range of your wireless network depends on many factors, including the abilities of your access

point and network adapters. If you are having trouble printing, then try placing the computer and

  • From 8 to 63 ASCII characters. ASCII characters are letters, numbers, and symbols found on a keyboard. ASCII characters in a WPA passphrase are case ‑ sensitive.

There may be temporary interference from electronic devices such as microwave ovens or other

C HECK IF YOUR ACCESS POINT HAS AN ASSOCIATION / REGISTRATION BUTTON

MOVE THE COMPUTER AND/OR PRINTER CLOSER TO THE ACCESS POINT

M OVE YOUR ACCESS POINT AWAY FROM OTHER ELECTRONIC DEVICES

the access point, or contact the person who set up your wireless network.

M AKE SURE YOUR COMPUTER IS CONNECTED TO YOUR ACCESS POINT

with your box, or contact your Internet Service Provider (ISP).

is not positioned too closely to these devices.

then another factor is causing the problem.

C HECK YOUR ADVANCED SECURITY SETTINGS

point, or contact your system support person.

printer no more than 100 feet apart.

C HECK THE WIRELESS SIGNAL QUALITY

printer to your wireless network.

to the access point.

Troubleshooting 49 · 1 Click

Page 50 of the Lexmark PRO710 user manual — wirelessly
Page 50 · click to enlarge
Page 50

If you see this message again after you have waited long enough for the printer and the laptop to attach

> Setup > > Network Setup > > Wireless 802.11 b/g/n > > Network Connection

If the printer or the laptop does not have an IP address, or if either has an address of 169.254.x.y (where

If the printer or the laptop still does not receive a valid IP address, then there is a problem with your

  • Make sure your access point (wireless router) is turned on and is working.
  • Remove any objects that could be blocking the signal.
  • Temporarily turn off any unnecessary wireless devices on your network and pause any network ‑ intensive activities, like large file transfers or network games. If the network is too busy,

3 If you are connected over a wireless network, then choose AirPort from the Active Services list.

The IP address appears as four sets of numbers separated by periods, such as 192.168.0.100.

1 Turn off the device that does not have a valid IP address (the laptop, the printer, or both).

then it is possible that the printer is not receiving the IP address within the allowed time.

to the network, then there may be a problem with your wireless network.

x and y are any two numbers between 0 and 255), then do the following:

Make sure that the laptop and printer have both received IP addresses:

2 Turn on the device, and then check the IP addresses again.

  • View the printer settings. From the printer control panel, navigate to:

The Router entry is typically the access point.

  • From the printer, print a network setup page.

Setup > > TCP/IP > > IP Address >

, or click Start and then click Run.

2 From the Contents pane, choose Network.

2 In the Start Search or Run box, type cmd.

In the TCP/IP section, look for Address.

4 Type ipconfig, and then press Enter.

1 From the Apple menu, navigate to:

wireless network. Try the following:

About This Mac > More Info

Locating the printer IP address

3 Press Enter, or click OK.

1 Type the IP address of the access point in the address field of your Web browser, and then continue to step 2.

The printer supports wireless printing only through AirPort base stations for Mac OS X version 10.5 or

If you are using a laptop and have power saving settings enabled, then you may see the ”Communication

not available” message on your computer screen when you attempt to print wirelessly. This can occur

If you see this message, then wait a few seconds and then try to print again. The laptop and printer

The SSID of the network that the computer is connected to is displayed in the Network menu.

  • Make sure you copy the network information down exactly, including any capital letters.
  • Store the SSID and the WEP key or WPA passphrase in a safe place for future reference.

MAKE SURE YOUR COMPUTER AND PRINTER HAVE VALID IP ADDRESSES FOR THE NETWORK

“Communication not available” message appears when printing

MAKE SURE YOUR OS IS COMPATIBLE WITH WIRELESS PRINTING THROUGH AIRPORT

4 Write down the SSID, security type, and the WEP key/WPA passphrase (if shown).

If you do not know the IP address of the access point, then do the following:

require a few seconds to power up again and reattach to the wireless network.

2 Type your user name and password when prompted, and then click OK.

The Router entry is typically the access point.

3 In the Wireless settings section, look for the SSID.

System Preferences > Network > AirPort

Applications > Internet Connect > AirPort

For Macintosh users with an access point

a From the Apple menu, navigate to:

if the laptop hard drive has powered down.

b Click Advanced or Configure.

In Mac OS X version 10.4 or earlier

1 From the Finder, navigate to:

Try one or more of the following:

2 Write down the SSID.

c Click TCP/IP.

wirelessly

later.

Show 4 more labels / short text on this page
Troubleshooting 50 · For Macintosh users · For Windows users · 1 Click
Page 51 of the Lexmark PRO710 user manual — M AKE SURE THE WIRELESS PORT IS SELECTED
Page 51 · click to enlarge
Page 51
  • Make sure your DHCP server, which may also be your wireless router, is working and is configured to assign IP addresses. If you are not sure how to do this, then refer to the manual that came with

6 If the Description column of the selected port indicates that it is a USB port, then scroll through the list and select the port with Printer Port in the Description column. Check the printer model in the

If the printer and computer have valid IP addresses and the network is operating correctly, then

4 Right‑click the printer, and then select Properties or Printer properties from the menu.

4 Right‑click the printer, and then select Properties or Printer properties from the menu.

6 Click the box next to Enable bidirectional support if it is not already checked.

The selected port has a check mark beside it in the Port column.

Printer column to make sure you select the right printer port.

2 In the Start Search or Run box, type control printers.

2 In the Start Search or Run box, type control printers.

M AKE SURE BIDIRECTIONAL COMMUNICATION IS ENABLED

5 Click the Ports tab, and then locate the selected port.

, or click Start and then click Run.

, or click Start and then click Run.

7 Click Apply > OK, and then try to print again.

M AKE SURE THE WIRELESS PORT IS SELECTED

7 Click OK, and then try to print again.

3 Press Enter, or click OK.

3 Press Enter, or click OK.

continue troubleshooting.

your wireless router.

5 Click the Ports tab.

Troubleshooting 51 · 1 Click · 1 Click

Page 52 of the Lexmark PRO710 user manual — USA
Page 52 · click to enlarge
Page 52

1 this device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation.

This product complies with Part 68 of the FCC Rules. See the product online documentation for additional

This product complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

Federal Communications Commission (FCC) compliance information

Federal Communications Commission (FCC) compliance information

For additional compliance information, see the online documentation.

All other trademarks are the property of their respective owners.

Any questions on this statement should be directed to:

Operation is subject to the following two conditions:

Director of Lexmark Technology & Services

Lexmark International, Inc.

740 West New Circle Road Lexington, KY 40550

compliance information.

statement

statement

OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of

intends to make these available in all countries in which it operates. Any reference to a product, program,

or service is not intended to state or imply that only that product, program, or service may be used. Any

The following paragraph does not apply to any country where such provisions are inconsistent with

local lawLEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY

made to the information herein; these changes will be incorporated in later editions. Improvements or

property right may be used instead. Evaluation and verification of operation in conjunction with other

products, programs, or services, except those expressly designated by the manufacturer, are the user’s

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in

express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically

References in this publication to products, programs, or services do not imply that the manufacturer

This software and any accompanying documentation provided under this agreement are commercial

functionally equivalent product, program, or service that does not infringe any existing intellectual

computer software and documentation developed exclusively at private expense.

changes in the products or the programs described may be made at any time.

If you don't have access to the Internet, you can contact Lexmark by mail:

For information on supplies and downloads, visit www.lexmark.com.

For Lexmark technical support, visit support.lexmark.com.

UNITED STATES GOVERNMENT RIGHTS

the United States and/or other countries.

© 2011 Lexmark International, Inc.

Lexmark International, Inc.

740 New Circle Road NW Lexington, KY 40550

Edition notice

All rights reserved.

Trademarks

Notices

responsibility.

USA

(859) 232-3000 · Bldg 004-2/CSC · December 2011

Page 54 of the Lexmark PRO710 user manual — Table of contents
Page 54 · click to enlarge
Page 54

Table of contents

Contentsp.3About your printerp.5Finding information about the printerp.5Minimizing your printer's environmental impactp.5Printer modelsp.6Printer featuresp.6Setting up the printerp.6Understanding the parts of the printerp.12Using the printer control panelp.13Using flash drivesp.14Supported file typesp.14Using a flash drive with the printerp.15Ordering and replacing suppliesp.16Ordering ink cartridgesp.16Replacing ink cartridgesp.16Maintaining ink cartridgesp.18Aligning the printheadp.18Cleaning the printhead nozzlesp.18Using the printer softwarep.19Minimum system requirementsp.19Installing the printer softwarep.19Using the Windows printer softwarep.19Using the Macintosh printer softwarep.20Printingp.22Printing a documentp.22Printing on both sides of the paper (duplexing) automaticallyp.22Printing photos from a flash drivep.23Printing documents from a flash drivep.23Canceling print jobsp.23Printing from a mobile devicep.24What is LexPrint?p.24Supported printersp.24Copyingp.25Tips for copyingp.25Making copiesp.25Making a two-sided (duplex) copy automaticallyp.25Canceling copy jobsp.26Scanningp.27Tips for scanningp.27Scanning to a local computerp.27Scanning to a flash drive or memory cardp.27Scanning directly to e-mail using the printer softwarep.27Scanning to a PDFp.28Canceling scan jobsp.28E-mailingp.29Sending e-mailp.29Tips for e-mailingp.29Setting up the e-mail functionp.29Canceling an e-mailp.29Setting up the printer to faxp.30Step 1: Connect the printer to the telephone linep.30Scenario 1: Standard telephone linep.30Scenario 2: Digital Subscriber Line (DSL)p.32Scenario 3: VoIP telephone servicep.32Scenario 4: Digital telephone service through a cable providerp.33Scenario 5: Countryor region-specific setupp.34Step 2: Check the dial tonep.37Step 3: Set your fax name and fax numberp.37Step 4: Set the printer to receive faxes automatically or manuallyp.37Step 5: Set the number of ringsp.38Step 6: Create a contact listp.38Faxingp.39Sending faxesp.39Tips for sending faxesp.39Sending faxes using the printer control panelp.39Sending faxes using the computerp.39Receiving faxesp.39Tips for receiving faxesp.39Receiving faxes automaticallyp.40Receiving faxes manuallyp.40Wireless networkingp.41Information you will need to set up the printer on a wireless networkp.41Installing the printer on a wireless networkp.41What is Wi-Fi Protected Setup?p.41Configuring Wi-Fi Protected Setup manuallyp.42Use the Push Button Configuration (PBC) methodp.42Use the Personal Identification Number (PIN) methodp.42Troubleshootingp.43Before you troubleshootp.43If Troubleshooting does not solve your problemp.43Setup troubleshootingp.43Incorrect language appears on the displayp.43Change the language using the printer menusp.43Installation screen did not appear during installationp.43Launch the printer CD manuallyp.43Software did not installp.43Make sure that your computer meets the minimum system requirementsp.43Temporarily disable security programs in Windows before installing the softwarep.43Check the USB connectionp.44Reconnect the printer power supplyp.44Print job does not print or is missing pagesp.44Make sure the ink cartridges are inserted correctlyp.44Select your printer from the Print dialog before sending the print jobp.44Make sure the print job is not pausedp.44Make sure your printer is set as the default printerp.44Reconnect the printer power supplyp.44Remove and reconnect the USB cable connected to your printerp.44Check the USB connectionp.44Remove and reinstall the printer softwarep.44Printer is printing blank pagesp.44Reinstall the ink cartridges and deep clean and align the printheadp.44Printer is busy or does not respondp.45Make sure the printer is not in Sleep modep.45Reconnect the printer power supplyp.45Cannot delete documents from the print queuep.45Restart the computer and try againp.45Remove and reconnect the USB cable connected to your printerp.45Cannot print through USBp.45Check the USB connectionp.45Make sure the USB port is enabled in Windowsp.45Remove and reinstall the printer softwarep.45Fax troubleshootingp.45Fax troubleshooting checklistp.46Cannot send faxesp.46Make sure that you have registered your user information in the printerp.46Decrease the transmission speed of the fax modemp.46Enable error correctionp.46Enable automatic fax conversionp.46Make sure that the Dial Prefix setting is correctp.46Cannot receive faxesp.47Make sure that you have configured the correct settings for your setupp.47Make sure that the printer is connected to an analog portp.47Make sure that the printer memory is not fullp.47Make sure that Fax Forwarding is disabledp.47Increase the ringer volumep.47Make sure that you have the correct manual answer codep.47Cannot run the fax softwarep.47Make sure a fax driver is installedp.47Make sure the printer is connected to a telephone linep.47Wireless network troubleshootingp.47Wireless troubleshooting checklistp.47Printing a network setup pagep.48Locating IP addressesp.48Cannot print over wireless networkp.48Turn the access point (wireless router) off and then back onp.48Disconnect from VPN sessionp.48Make sure Demo Mode is turned offp.48Check your WEP key or WPA passphrasep.48Check if your access point has an association/registration buttonp.49Move your access point away from other electronic devicesp.49Move the computer and/or printer closer to the access pointp.49Check the wireless signal qualityp.49Check your advanced security settingsp.49Make sure your computer is connected to your access pointp.49Make sure that your computer and printer are connected to the same wireless networkp.49Make sure your OS is compatible with wireless printing through AirPortp.50“Communication not available” message appears when printing wirelesslyp.50Make sure your computer and printer have valid IP addresses for the networkp.50Make sure the wireless port is selectedp.51Make sure bidirectional communication is enabledp.51Noticesp.52Edition noticep.52UNITED STATES GOVERNMENT RIGHTSp.52Trademarksp.52Federal Communications Commission (FCC) compliance information statementp.52Federal Communications Commission (FCC) compliance information statementp.52Indexp.53
Page 55 of the Lexmark PRO710 user manual — Table of contents
Page 55 · click to enlarge
Page 55

Table of contents

Contentsp.3About your printerp.5Finding information about the printerp.5Minimizing your printer's environmental impactp.5Printer modelsp.6Printer featuresp.6Setting up the printerp.6Understanding the parts of the printerp.12Using the printer control panelp.13Using flash drivesp.14Supported file typesp.14Using a flash drive with the printerp.15Ordering and replacing suppliesp.16Ordering ink cartridgesp.16Replacing ink cartridgesp.16Maintaining ink cartridgesp.18Aligning the printheadp.18Cleaning the printhead nozzlesp.18Using the printer softwarep.19Minimum system requirementsp.19Installing the printer softwarep.19Using the Windows printer softwarep.19Using the Macintosh printer softwarep.20Printingp.22Printing a documentp.22Printing on both sides of the paper (duplexing) automaticallyp.22Printing photos from a flash drivep.23Printing documents from a flash drivep.23Canceling print jobsp.23Printing from a mobile devicep.24What is LexPrint?p.24Supported printersp.24Copyingp.25Tips for copyingp.25Making copiesp.25Making a two-sided (duplex) copy automaticallyp.25Canceling copy jobsp.26Scanningp.27Tips for scanningp.27Scanning to a local computerp.27Scanning to a flash drive or memory cardp.27Scanning directly to e-mail using the printer softwarep.27Scanning to a PDFp.28Canceling scan jobsp.28E-mailingp.29Sending e-mailp.29Tips for e-mailingp.29Setting up the e-mail functionp.29Canceling an e-mailp.29Setting up the printer to faxp.30Step 1: Connect the printer to the telephone linep.30Scenario 1: Standard telephone linep.30Scenario 2: Digital Subscriber Line (DSL)p.32Scenario 3: VoIP telephone servicep.32Scenario 4: Digital telephone service through a cable providerp.33Scenario 5: Countryor region-specific setupp.34Step 2: Check the dial tonep.37Step 3: Set your fax name and fax numberp.37Step 4: Set the printer to receive faxes automatically or manuallyp.37Step 5: Set the number of ringsp.38Step 6: Create a contact listp.38Faxingp.39Sending faxesp.39Tips for sending faxesp.39Sending faxes using the printer control panelp.39Sending faxes using the computerp.39Receiving faxesp.39Tips for receiving faxesp.39Receiving faxes automaticallyp.40Receiving faxes manuallyp.40Wireless networkingp.41Information you will need to set up the printer on a wireless networkp.41Installing the printer on a wireless networkp.41What is Wi-Fi Protected Setup?p.41Configuring Wi-Fi Protected Setup manuallyp.42Use the Push Button Configuration (PBC) methodp.42Use the Personal Identification Number (PIN) methodp.42Troubleshootingp.43Before you troubleshootp.43If Troubleshooting does not solve your problemp.43Setup troubleshootingp.43Incorrect language appears on the displayp.43Change the language using the printer menusp.43Installation screen did not appear during installationp.43Launch the printer CD manuallyp.43Software did not installp.43Make sure that your computer meets the minimum system requirementsp.43Temporarily disable security programs in Windows before installing the softwarep.43Check the USB connectionp.44Reconnect the printer power supplyp.44Print job does not print or is missing pagesp.44Make sure the ink cartridges are inserted correctlyp.44Select your printer from the Print dialog before sending the print jobp.44Make sure the print job is not pausedp.44Make sure your printer is set as the default printerp.44Reconnect the printer power supplyp.44Remove and reconnect the USB cable connected to your printerp.44Check the USB connectionp.44Remove and reinstall the printer softwarep.44Printer is printing blank pagesp.44Reinstall the ink cartridges and deep clean and align the printheadp.44Printer is busy or does not respondp.45Make sure the printer is not in Sleep modep.45Reconnect the printer power supplyp.45Cannot delete documents from the print queuep.45Restart the computer and try againp.45Remove and reconnect the USB cable connected to your printerp.45Cannot print through USBp.45Check the USB connectionp.45Make sure the USB port is enabled in Windowsp.45Remove and reinstall the printer softwarep.45Fax troubleshootingp.45Fax troubleshooting checklistp.46Cannot send faxesp.46Make sure that you have registered your user information in the printerp.46Decrease the transmission speed of the fax modemp.46Enable error correctionp.46Enable automatic fax conversionp.46Make sure that the Dial Prefix setting is correctp.46Cannot receive faxesp.47Make sure that you have configured the correct settings for your setupp.47Make sure that the printer is connected to an analog portp.47Make sure that the printer memory is not fullp.47Make sure that Fax Forwarding is disabledp.47Increase the ringer volumep.47Make sure that you have the correct manual answer codep.47Cannot run the fax softwarep.47Make sure a fax driver is installedp.47Make sure the printer is connected to a telephone linep.47Wireless network troubleshootingp.47Wireless troubleshooting checklistp.47Printing a network setup pagep.48Locating IP addressesp.48Cannot print over wireless networkp.48Turn the access point (wireless router) off and then back onp.48Disconnect from VPN sessionp.48Make sure Demo Mode is turned offp.48Check your WEP key or WPA passphrasep.48Check if your access point has an association/registration buttonp.49Move your access point away from other electronic devicesp.49Move the computer and/or printer closer to the access pointp.49Check the wireless signal qualityp.49Check your advanced security settingsp.49Make sure your computer is connected to your access pointp.49Make sure that your computer and printer are connected to the same wireless networkp.49Make sure your OS is compatible with wireless printing through AirPortp.50“Communication not available” message appears when printing wirelesslyp.50Make sure your computer and printer have valid IP addresses for the networkp.50Make sure the wireless port is selectedp.51Make sure bidirectional communication is enabledp.51Noticesp.52Edition noticep.52UNITED STATES GOVERNMENT RIGHTSp.52Trademarksp.52Federal Communications Commission (FCC) compliance information statementp.52Federal Communications Commission (FCC) compliance information statementp.52Indexp.53
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the Lexmark PRO710

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lexmark PRO710

Be the first to ask — other owners or our team will answer.

Original document

Lexmark PRO710 manual PDF

55 pages·3.5 MB·Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…