EN
Lexmark logo
Official user manual

Lexmark Printer

248 pages·3.6 MB·Printer·PDF·ENDEFRITNLJA
Lexmark Printer
Table of Contents 153 sections Preface · 1. General Information · Power Consumption · Internal Power Supply Specifications · … ShowHide
Prefacep.71. General Informationp.13Power Consumptionp.13Internal Power Supply Specificationsp.14Maintenance Approachp.14Tools Required For Servicep.15Abbreviationsp.15Operator Panel and Menusp.16Using the Operator Panelp.16Power Indicator Statesp.16Operator Panel Button Functionsp.17Printer Messagesp.18Operator Panel Menusp.19Printing the Menu Settings Pagep.20Changing Printer Settingsp.21Disabling the Operator Panel Menusp.222. Diagnostic Informationp.23Startp.23Service Messagesp.24Error Indicator Tablep.25User Status Messagesp.32Warning Messagesp.35Status Messagesp.36Attendance Messagesp.46Overriding Change Promptsp.50Paper Jamsp.62Power-On Self Test (POST) Sequencep.70Post Symptom Tablep.71Symptom Tablesp.72Service Checksp.75Maintenance Functionsp.75Maintenance Station Service Checksp.77Index Motor Service Checkp.78Sensor Checksp.78Multi-Purpose Feeder (MPF) Motor and Sensor Service Checkp.79Operator Panel (Buttons) Service Checkp.80Operator Panel (LCD) Display Service Checkp.81Options Service Checkp.81Paper Feed Service Checkp.82Power Supply Service Checkp.85RIP Card Service Checkp.86Print Quality Service Checkp.87Index Card/Sensor Service Checkp.89Transport Service Checkp.89Cam System Motor/Sensor Service Checkp.91User Error Messagesp.913. Diagnostic Aidsp.95Printer Operationsp.95Operations Initiated by Pressing Buttons at Power-On Resetp.95Change Ink Cartridgesp.98Change Printheadsp.98Aligning the Printheadsp.99Cleaning Printheadsp.101Linking Input Traysp.102Unsolicited Manual Feedp.104Manual Duplexp.104Printing Menu Settings Pagep.104Restoring Factory Defaultsp.106Canceling a Print Job using the Operator Panelp.106Resetting the Printer using the Operator Panelp.108Other Resetsp.111Activating Hex Trace Debug Modep.113Diagnostics (Mode 1) - Print Testsp.113Diagnostics (Mode 2) - Hardware Testsp.116Diagnostics (Mode 2) - Input Tray Testsp.121Diagnostics (Mode 2) - Base Sensor Testsp.123Diagnostics (Mode 2) - Subsystem Testsp.125Diagnostics (Mode 2) - Supplies Testsp.128Diagnostics (Mode 2) - Printer Setupp.129Diagnostics (Mode 2) - Error Logp.131Menusp.133Understanding the Menu Display and Menu Buttonsp.133Example of Modifying a Printer Setting Using the Operator Panelp.136Operator Panel Menu Definitionp.138Busy/Waiting Menu Groupp.139Job Menup.140Ready Menu Groupp.142Configuration Menu Groupp.154Diagnostics Menu Group (Mode 1: Printing)p.156Diagnostics Menu Group (Mode 2: Non-printing)p.1574. Repair Informationp.161Handling ESD-Sensitive Partsp.161Adjustmentsp.162Removal Proceduresp.162Releasing Plastic Latchesp.162Rear Cover Removalp.163Operator Panel Cover/Operator Panel Removalp.165Exit Tray Removalp.165Left Frame Cover Removalp.166Left Cover Removalp.167Right Cover/Power Switch Removalp.169Left Tray Cover Removalp.171Right Tray Cover Removalp.172Ink Levels and Temperature Sensor with Bracket Removalp.173Engine Board /Cover Removalp.174Carrier with Card Removalp.175Carrier 1st Stage Drive Belt Removalp.177Carrier Printhead Latch Removalp.177Multi-Purpose Feeder (MPF) Motor and Sensor Removalp.177Power Supply Removalp.179Pump Housing/Maintenance Station/Ink Waste Tank/ Transport Carrier Motor Removalp.180Index Card Assembly Removalp.182Cover-Open Sensor Removalp.183RIP-EMC Shield Assembly/RIP Card Removalp.184PerfectFinish Sensor Assembly/Rear Paper Path Sensor Removalp.186Frame From Base Removalp.187Cam Engine Motor with Gear Removalp.189Paper Feed Pick Arm Assembly with Motor and Paper Path Sensor Removalp.191PerfectFinish Gear Plate Removalp.192PerfectFinish Motor Removalp.193Index Motor Assembly Removalp.193Encoder Disk Feed Roller Assembly Removalp.194Star Wheel Shaft Assembly Removalp.196Paper Feed Platen Assembly Removalp.198Exit Shaft with Gear Removalp.199Paper Feed Frame and Motor/Cam Shaft Assembly Removalp.200Left Index Frame Pivot Assembly Removalp.203Right Index Frame Pivot Assembly Removalp.205Bat Wings and Bushings Removalp.206Backup Roller Assembly Removalp.207Backup Roller Spring Removalp.208Carrier/Cable Retainer Removalp.208Peristaltic Pump Removalp.209Tray 2 Covers Removalp.209Tray 2 Paper Pick Arm Assembly Removalp.210Tray 2 Paper Feed Motor and Card Assembly Removalp.2125. Connector Locationsp.213Engine Boardp.213RIP Cardp.214RIP Card (cont.)p.215Optional Tray 2p.2166. Preventive Maintenancep.217Lubrication Specificationsp.2177. Parts Catalogp.219How To Use The Parts Catalogp.219Bp.245Cp.245Dp.245Ep.245Hp.245Ip.245Jp.245Lp.245Mp.245Op.245Pp.245Rp.246Sp.246Tp.247Up.247Wp.247Part Numbersp.247Indexp.245
Page 1 of the Lexmark Printer user manual — Lexmark J110
Page 1 · click to enlarge
Page 1

Lexmark J110

4085-001

  • Table of Contents
  • Start Diagnostics
  • Safety and Notices
  • Trademarks
  • Index
  • Manuals Menu

Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.

Page 2 of the Lexmark Printer user manual — U.S.A. P/N: 12G3639
Page 2 · click to enlarge
Page 2

4085-001

EditionAugust 2001

The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time.

Comments may be addressed to Lexmark International, Inc., Department D22A/032-2, 740 West New Circle Road, Lexington, Kentucky 40550, U.S.A or e-mail at ServiceInfoAndTraining@Lexmark.com. Lexmark may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. You can purchase additional copies of publications related to this product by calling 1-800-553-9727. In other countries, contact your point of purchase.

Lexmark, Lexmark with diamond design, MarkNet, and Optra are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.

OptraImage and PerfectFinish are trademarks of Lexmark International, Inc.

Other trademarks are the property of their respective owners.

© Copyright Lexmark International, Inc. 2001. All rights reserved.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS This software and documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 and in applicable FAR provisions: Lexmark International, Inc., Lexington, KY 40550.

U.S.A. P/N: 12G3639

Page 3 of the Lexmark Printer user manual — 4085-001
Page 3 · click to enlarge
Page 3

4085-001

Table of Contents

Preface vii

Safety Information viii

General Information 1-1

Power Consumption 1-1 Internal Power Supply Specifications 1-2 Maintenance Approach 1-2 Tools Required For Service 1-3 Abbreviations 1-3 Operator Panel and Menus 1-4

Using the Operator Panel 1-4 Menu 1-4 Select 1-4 Return 1-4 Go 1-4 Stop 1-4 Power Indicator States 1-4 Operator Panel Button Functions 1-5 Printer Messages 1-6 Operator Panel Menus 1-7

Printing the Menu Settings Page 1-8 Changing Printer Settings 1-9 Disabling the Operator Panel Menus 1-10

Diagnostic Information 2-1

Start 2-1

Service Messages 2-2 Error Indicator Table 2-3 User Status Messages 2-10

Warning Messages 2-13 Status Messages 2-14

2-15 2-17 2-19 2-20 2-20 2-21 2-22 2-23 Attendance Messages 2-24

Page 4 of the Lexmark Printer user manual — 4085-00X
Page 4 · click to enlarge
Page 4

4085-00X

2-25 2-26 Overriding Change Prompts 2-28 Paper Jams 2-40 Power-On Self Test (POST) Sequence 2-48 Post Symptom Table 2-49 Symptom Tables 2-50 Service Checks 2-53

Maintenance Functions 2-53 Maintenance Station Service Checks 2-55 Index Motor Service Check 2-56 Sensor Checks 2-56 Multi-Purpose Feeder (MPF) Motor and Sensor Service Check .2-57 Operator Panel (Buttons) Service Check 2-58 Operator Panel (LCD) Display Service Check 2-59 Options Service Check 2-59 Paper Feed Service Check 2-60 Power Supply Service Check 2-63 RIP Card Service Check 2-64 Print Quality Service Check 2-65 Index Card/Sensor Service Check 2-67 Transport Service Check 2-67 Cam System Motor/Sensor Service Check 2-69 User Error Messages 2-69

Diagnostic Aids 3-1

Printer Operations 3-1

Operations Initiated by Pressing Buttons at Power-On Reset 3-1 Change Ink Cartridges 3-4 Change Printheads 3-4 Aligning the Printheads 3-5 Cleaning Printheads 3-7 Linking Input Trays 3-8 Unsolicited Manual Feed 3-10 Manual Duplex 3-10 Printing Menu Settings Page 3-10 Restoring Factory Defaults 3-12 Canceling a Print Job using the Operator Panel 3-12 Resetting the Printer using the Operator Panel 3-14 Other Resets 3-17 Activating Hex Trace Debug Mode 3-19 Diagnostics (Mode 1) - Print Tests 3-19 Diagnostics (Mode 2) - Hardware Tests 3-22

iv Service Manual

Page 5 of the Lexmark Printer user manual — 4085-001
Page 5 · click to enlarge
Page 5

4085-001

Diagnostics (Mode 2) - Input Tray Tests 3-27 Diagnostics (Mode 2) - Base Sensor Tests 3-29 Diagnostics (Mode 2) - Subsystem Tests 3-31 Diagnostics (Mode 2) - Supplies Tests 3-34 Diagnostics (Mode 2) - Printer Setup 3-35 Diagnostics (Mode 2) - Error Log 3-37 Menus 3-39

Understanding the Menu Display and Menu Buttons 3-39 Example of Modifying a Printer Setting Using the Operator Panel . . 3-42 Operator Panel Menu Definition 3-44 Busy/Waiting Menu Group 3-45 Job Menu 3-46 Ready Menu Group 3-48 Configuration Menu Group 3-60 Diagnostics Menu Group (Mode 1: Printing) 3-62 Diagnostics Menu Group (Mode 2: Non-printing) 3-63

Repair Information 4-1

Handling ESD-Sensitive Parts 4-1 Adjustments 4-2 Removal Procedures 4-2

Releasing Plastic Latches 4-2 Rear Cover Removal 4-3 Operator Panel Cover/Operator Panel Removal 4-5 Exit Tray Removal 4-5 Left Frame Cover Removal 4-6 Left Cover Removal 4-7 Right Cover/Power Switch Removal 4-9 Left Tray Cover Removal 4-11 Right Tray Cover Removal 4-12 Ink Levels and Temperature Sensor with Bracket Removal . . . 4-13 Engine Board /Cover Removal 4-14 Carrier with Card Removal 4-15 Carrier 1st Stage Drive Belt Removal 4-17 Carrier Printhead Latch Removal 4-17 Multi-Purpose Feeder (MPF) Motor and Sensor Removal 4-17 Power Supply Removal 4-19 Pump Housing/Maintenance Station/Ink Waste Tank/Transport Car- rier Motor Removal 4-20 Index Card Assembly Removal 4-22 Cover-Open Sensor Removal 4-23 RIP-EMC Shield Assembly/RIP Card Removal 4-24

Page 6 of the Lexmark Printer user manual — 4085-00X
Page 6 · click to enlarge
Page 6

4085-00X

PerfectFinish Sensor Assembly/Rear Paper Path Sensor Removal . 4-26 Frame From Base Removal 4-27 Cam Engine Motor with Gear Removal 4-29 Paper Feed Pick Arm Assembly with Motor and Paper Path Sensor Removal 4-31 PerfectFinish Gear Plate Removal 4-32 PerfectFinish Motor Removal 4-33 Index Motor Assembly Removal 4-33 Encoder Disk Feed Roller Assembly Removal 4-34 Star Wheel Shaft Assembly Removal 4-36 Paper Feed Platen Assembly Removal 4-38 Exit Shaft with Gear Removal 4-39 Paper Feed Frame and Motor/Cam Shaft Assembly Removal . .4-40 Left Index Frame Pivot Assembly Removal 4-43 Right Index Frame Pivot Assembly Removal 4-45 Bat Wings and Bushings Removal 4-46 Backup Roller Assembly Removal 4-47 Backup Roller Spring Removal 4-48 Carrier/Cable Retainer Removal 4-48 Peristaltic Pump Removal 4-49 Tray 2 Covers Removal 4-49 Tray 2 Paper Pick Arm Assembly Removal 4-50 Tray 2 Paper Feed Motor and Card Assembly Removal 4-52

Connector Locations 5-1

Engine Board 5-1 RIP Card 5-2 RIP Card (cont.) 5-3 Optional Tray 2 5-4

Preventive Maintenance 6-1

Lubrication Specifications 6-1

Parts Catalog 7-1

How To Use The Parts Catalog 7-1

vi Service Manual

Page 7 of the Lexmark Printer user manual — 4085-001
Page 7 · click to enlarge
Page 7

4085-001

Preface

This manual describes the Lexmark J110 printer (4085-001) and contains maintenance procedures for service personnel only. It is divided into the following chapters:

1. General Information contains a general description of the printer and the maintenance approach used to repair it. Special tools and test equipment are listed in this chapter, as well as general environmental and safety instructions. 2. Diagnostic Information contains an error indicator table, symptom tables, and service checks used to isolate failing field replaceable units (FRUs). 3. Diagnostic Aids contains tests and checks used to locate or repeat symptoms of printer problems. 4. Repair Information provides instructions for making printer adjustments and removing and installing FRUs. 5. Connector Locations uses illustrations to identify the connector locations and test points on the printer. 6. Preventive Maintenance contains the lubrication specifications and recommendations to prevent problems. 7. Parts Catalog contains illustrations and part numbers for individual FRUs.

Preface vii

Page 9 of the Lexmark Printer user manual — Sicherheitshinweise
Page 9 · click to enlarge
Page 9

4085-001

Norme di sicurezza

  • Il prodotto è stato progettato, testato e approvato in conformità a severi standard di sicurezza e per l’utilizzo con componenti Lexmark specifici. Le caratteristiche di sicurezza di alcune parti non sempre sono di immediata comprensione. Lexmark non è responsabile per l’utilizzo di parti di ricambio di altri produttori.
  • Le informazioni riguardanti la manutenzione di questo prodotto sono indirizzate soltanto al personale di assistenza autorizzato.
  • Durante lo smontaggio e la manutenzione di questo prodotto, il rischio di subire scosse elettriche e danni alla persona è più elevato. Il personale di assistenza autorizzato, deve, quindi, adottare le precauzioni necessarie.

Sicherheitshinweise

  • Dieses Produkt und die zugehörigen Komponenten wurden entworfen und getestet, um beim Einsatz die weltweit gültigen Sicherheitsanforderungen zu erfüllen. Die sicherheitsrelevanten Funktionen der Bauteile und Optionen sind nicht immer offensichtlich. Sofern Teile eingesetzt werden, die nicht von Lexmark sind, wird von Lexmark keinerlei Verantwortung oder Haftung für dieses Produkt übernommen.
  • Die Wartungsinformationen für dieses Produkt sind ausschließlich für die Verwendung durch einen Wartungsfachmann bestimmt.
  • Während des Auseinandernehmens und der Wartung des Geräts besteht ein zusätzliches Risiko eines elektrischen Schlags und körperlicher Verletzung. Das zuständige Fachpersonal sollte entsprechende Vorsichtsmaßnahmen treffen.

Safety Information ix

Page 12 of the Lexmark Printer user manual — 4085-001
Page 12 · click to enlarge
Page 12

4085-001

Lexmark Printer — 4085-001 diagram (page 12)
Fig. 1
Lexmark Printer — 4085-001 diagram (page 12)
Fig. 2
Lexmark Printer — 4085-001 diagram (page 12)
Fig. 3

xii Service Manual

Page 13 of the Lexmark Printer user manual — Power Consumption
Page 13 · click to enlarge
Page 13

4085-001

1. General Information

The Lexmark™ J110 printer is a high-performance, narrow-format, thermal inkjet printer designed to print high quality text, graphics, and images on a wide variety of media. It is intended for use by single users or by small workgroups shared using an external network solution or peer-to-peer networking. This printer features parallel and USB standard connectivity. The printheads provide color and true black printing. The number and size of inkjets or nozzles, in the printhead, determines the overall quality and capability of the printer. The black printhead has 640 nozzles and the color printhead has 320 nozzles for each color.

Power Consumption

  • 2 Watts - Off Mode (conforms to Blue Angel power specifications in the Off Mode)
  • <20 Watts - Power Saver including options (conforms to Energy Star Sleep Mode specification in Power Saver). The printer goes to low power mode when not printing.
  • 50 Watts - Printing Mode Maximum Average (approximately)
  • 90 Watts - Printing Mode Peak (approximately)

General Information 1-1

Page 14 of the Lexmark Printer user manual — Maintenance Approach
Page 14 · click to enlarge
Page 14

4085-001

Internal Power Supply Specifications

Built-in Universal Power Supply, 40 Watts Output (50 Watts input) Outputs:

Maximum Voltage Load Range

+5 V + 5.1 V +4.8 V +5.25 V 0.5 Amps Min. 1.6 Amps Max. 2.0 Amps Peak

+36 V +36.0 V +32.4 V +39.6 V 0.1 Amps Min. 1.0 Amps Max. Avg. (1) 2.1 Amps Peak (1) 3.2 Amps Max. Peak (1)

Maintenance Approach

The diagnostic information in this manual leads you to the correct field replaceable unit (FRU) or part. Use the error indicator charts, symptom index, service checks, and diagnostic aids to determine the symptom and repair the failure.

This printer can be serviced without being connected to a host computer. The user is directed, in the Printer Control program, to perform the head to head and bidirectional alignment adjustments after replacing a print cartridge.

After you complete the repair, perform tests as needed to verify the repair.

Output Name · Nominal Voltage · Minimum Voltage

Page 15 of the Lexmark Printer user manual — Abbreviations
Page 15 · click to enlarge
Page 15

4085-001

Tools Required For Service

  • Analog or digital multimeter
  • Parallel wrap plug P/N 1319128
  • Pliers: diagonal and needle-nose
  • Screwdrivers: #1 and #2 Phillips
  • Magnet

Abbreviations

EOF End of Forms ESD Electrostatic Discharge FRU Field Replaceable Unit LED Light-Emitting Diode MPF Multi-Purpose Feeder NPA Network Printer Alliance POR Power-On Reset POST Power-On Self Test SIMM Single In-line Memory Module RAM Random Access Memory ROM Read Only Memory V ac Volts alternating current V dc Volts direct current

General Information 1-3

Page 16 of the Lexmark Printer user manual — Power Indicator States
Page 16 · click to enlarge
Page 16

4085-001

Operator Panel and Menus

Using the Operator Panel

The operator panel, on the front right side of your printer, has a 2-line by 16-character liquid crystal display (LCD), six buttons (Menu is actually two buttons), and one power indicator light. The buttons have fixed functions, which are designated on the front cover.

Power Indicator Light Menu Select Return

Power Indicator States

The power indicator light gives information about the status of your printer.

Off Printer is powered off.

On Printer is powered on and the printer is idle.

Flashing Printer is powered on and the printer is busy.

Operator Panel Display · Go Stop · Power Indicator Meaning

Page 17 of the Lexmark Printer user manual — 4085-001
Page 17 · click to enlarge
Page 17

4085-001

Operator Panel Button Functions

Use the six operator panel buttons to open a menu, scroll through a list of values, change printer settings, and respond to printer messages. The following table describes the functions of each button.

Go Press the Go button.

This button is used to place the printer in the Ready state after an off line situation. For instance, Go can be used to exit the menus, and it can also be used to clear most Attendance messages. Menu> Press Menu> to enter a menu group. The first menu in the menu group is displayed.

Once a menu group is active, press Menu> to step to the next selection.

To automatically increment a numerical printer setting, press and hold Menu>. Release Menu> when the number you want is displayed. Menu< Press Menu< to enter a menu group. The last menu group is displayed.

Once a menu group is active, press Menu< to step to the previous selection.

To automatically decrement a numerical printer setting, press and hold Menu<. Release Menu< when the number you want is displayed. Select Press the Select button.

Select the menu selection displayed on the second line of the display. If a menu is displayed, such as Paper Menu, then Select opens the menu and displays the first printer setting contained in the menu.

If a menu item such as Paper Source is displayed, then Select opens the item and displays the default setting.

If a menu item setting such as Tray 2 is displayed, then Select saves the selection as the new default setting for Paper Source. The printer displays the Saved message momentarily and then returns to the menu item level.

Button Function · General Information 1-5

Page 18 of the Lexmark Printer user manual — Printer Messages
Page 18 · click to enlarge
Page 18

4085-001

Return Press the Return button.

Returns to the previous menu level. If at the top level of the menus, then it functions like Go. Stop Press the Stop button.

Stop suspends job activity and displays the Not Ready message. Job activity resumes when Go is pressed.

Printer Messages

The operator panel displays three types of messages:

  • Status messages provide information about the current state of the printer.
  • Attendance messages indicate printer errors that you must resolve.
  • Service messages indicate printer failures that may require servicing.

When the Ready status message displays, the printer is ready to receive a print job.

While a job is printing, the Busy status message appears on the first line of the operator panel display.

Button Function

Page 19 of the Lexmark Printer user manual — 4085-001
Page 19 · click to enlarge
Page 19

4085-001

Operator Panel Menus

Menus make it easy for you to change printer settings. Some menus appear only if a specific option is installed in the printer. Other menu items may only be effective for a particular printer language. You can select these values at any time, but they only affect printer function when you use the specified printer language.

An asterisk (*) next to a value indicates the original factory default setting and may vary for different countries. When you select a new setting from the operator panel, the asterisk moves next to the selected setting to identify it as the current user default. These settings are active until new ones are stored or the factory defaults are restored. Changes made from a software application or driver override the user default settings made from the printer operator panel.

General Information 1-7

Page 20 of the Lexmark Printer user manual — 4085-001
Page 20 · click to enlarge
Page 20

4085-001

Printing the Menu Settings Page

The menu settings page shows current settings for the menus and a list of installed options. You can use this page to verify that the printer options are properly installed and the printer settings are properly set.

To print a menu settings page:

1. Make sure the printer is plugged in and the Ready status message appears on the display. 2. Press Menu> or <Menu to enter the menus. 3. Continue to press and release Menu> until you see Utilities Menu. 4. Press Select. Utilities Menu appears on the first line and Print Menus is on the second line. 5. Press Select to select Print Menus. The message Printing Menu Settings appears and remains on the operator panel display until the page prints. The printer returns to the Ready state after the menu settings page prints. 6. If you installed options, verify that they are listed on the menu settings page under “Installed Features.” If an option you installed does not appear on the page, unplug the power cord and reinstall the option.

Page 21 of the Lexmark Printer user manual — 4085-001
Page 21 · click to enlarge
Page 21

4085-001

Changing Printer Settings

You can use the operator panel to change printer settings and customize your printer to meet your specific needs. To select a new value as the default setting:

1. From the Ready state, press Menu> or <Menu to enter the menus. 2. Continue to press and release Menu> or <Menu until the menu you need appears on the second line of the display. 3. Press Select. The menu opens and the first menu item in the menu appears on the second line of the display. 4. Press Menu> or <Menu until the menu item you need appears on the display. 5. Press Select. An asterisk (*) appears beside the current user default setting for that menu item. Note: Some menu items have sub-menus. You must select another menu (such as Tray 1 Type) before the available values display.

6. Press Menu> or <Menu until the value you need appears on the second line of the display. 7. Press Select. An asterisk (*) appears beside the value to indicate that it is now the user default setting. The display shows the new setting for one second and then clears. The Saved message displays, then the previous list of menu items appears on the operator panel display. 8. Press Return to go back to previous menus or menu items and set new default settings. 9. Press Go to return to Ready if this is the last printer setting you want to change. Note: User default settings remain in effect until you save new settings or restore the factory defaults. Changes made from a software application override the user default settings made from the printer operator panel.

General Information 1-9

Page 22 of the Lexmark Printer user manual — 4085-001
Page 22 · click to enlarge
Page 22

4085-001

Disabling the Operator Panel Menus

To disable the menus so that changes cannot be made to the printer default settings:

1. Turn off power. 2. While pressing Go and Stop , turn on the printer. 3. Release the buttons when Performing Self Test appears. When the printer self test completes, the Ready status message appears. If you press Menu> or
Page 23 of the Lexmark Printer user manual — Start
Page 23 · click to enlarge
Page 23

4085-001

2. Diagnostic Information

Use the error indicator table, symptom tables, service checks, and diagnostic aids to determine the printer failure.

Start

Service error indications are displayed on the operator panel. If your printer displays an error indication, locate the error number in the “Error Indicator Table” on page 2-3 . and take the indicated action. Turn the printer off and then back on to clear service errors.

Diagnostic Information 2-1

Page 24 of the Lexmark Printer user manual — Jam Jog Function
Page 24 · click to enlarge
Page 24

4085-001

Service Messages

These messages are displayed whenever the printer is in the Operator Intervention state, and the printer needs servicing. In general, service errors are non-recoverable. However, it may be possible to power the printer off and back on to temporarily recover from the error condition if it is intermittent in nature.

When a Service Message occurs, the printer stops printing. The only recovery is to turn off the printer.

Accessing Additional Debug Information for Service Errors

Additional debug information may be available for the specific service error being displayed. This information may help the Customer Support Center, customer engineer, and support engineer resolve the problem.

To access this information, complete the following steps:

1. Press and hold Return and then press and release Select . The first screen of debug information appears. Write down this information. 2. Continue pressing Return + Select until each screen of debug data is obtained. Once the end of the debug data is reached, the original service message is displayed.

Jam Jog Function

When in any 9XX error condition, you can press the Menu> button to implement the jam jog function. The jam jog function helps clear any pages that have been stopped mid-way through the paper path.

Page 25 of the Lexmark Printer user manual — 4085-001
Page 25 · click to enlarge
Page 25

4085-001

Error Indicator Table

900 RIP Software Perform the “RIP Card Service Check” on page 2-64 .

902 Engine Software Replace the engine board. See the “Engine Board / Cover Removal” on page 4-14 .

903 RIP Software Check RIP/Engine cable. Replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 .

904 Service Options Interface Check cables. Replace the board in the optional tray.

905 Engine Flash XX

Replace the engine board. See the “Engine Board / Cover Removal” on page 4-14 .

80 Flash Erase failure

81 Flash Programming failure

82 Flash - Invalid checksum on input data.

83 Flash - A failure occurred when programming this block.

906 Engine Board XX

Replace the engine board. See the “Engine Board / Cover Removal” on page 4-14 .

10 ASIC RAM failure

20 Engine Processor failure

21 Boot Code Checksum failure

22 Engine ASIC failure

23 Boot / Engine Card incompatibility

Error Symptom Action · Diagnostic Information 2-3

Page 26 of the Lexmark Printer user manual — 4085-001
Page 26 · click to enlarge
Page 26

4085-001

Check cabling to index board.

10 Invalid data in flash memory

10. Replace engine board. See “Engine Board /Cover Removal” on page 4-14 .

20 NVRAM checksum failure

30 Flash data programming failure

40 Engine NVRAM is not present or is not responding

20. Replace index board. See “Index Card Assembly Removal” on page 4-22 .

50 Password rejected by engine NVRAM

30. Replace engine board.

40 and 50 - Replace index board.

Check cabling to index board.

90 Decompression / Rebuild Failure

Replace index board. See “Index Card Assembly Removal” on page 4-22 .

Perform the “Carrier System Test” on page 3-32 .

10 Carrier Motor stall or loss of encoder signals

20 Encoder Quadrature error

30 Temperature Sense > Calibration failure

This would be caused by printhead contacts or carrier card. Note: “Carrier Systems Test” would not find this.

40 Carrier running backward

50 Carrier Velocity Overshoot

60 Starfire ASIC Reset failure

70 Printhead and Index Voltage Level failure

Show 4 more labels / short text on this page
Error Symptom Action · 907 Engine NVRAM · 908 Engine NVRAM · 910 Carrier System
Page 27 of the Lexmark Printer user manual — 4085-001
Page 27 · click to enlarge
Page 27

4085-001

Perform the “Index System Test” on page 3-33 .

10 Index Motor Stall or loss of Encoder signals

See “Index Motor Service Check” on page 2-56 . If problem still exists, go to “Index System Test” on page 3-33 .

20 Encoder Wheel “once-per- revolution” sensor failure

30 Unable to calibrate Analog Sensor

40 Index Motor wired backward

920 “Feed Motor” - Pick Motor stall or loss of Encoder signals

See “Index Card/Sensor Service Check” on page 2-67 .

921 PerfectFinish™ System - Motor stall or loss of Encoder signals

Check Motor and Encoder. See “Index Motor Service Check” on page 2-56 . If problem still exists, go to “Index System Test” on page 3-33 .

922 Multi-Purpose Feeder Motor - Motor stall or loss of Encoder signals

Check Multi-Purpose Feeder Motor. See “Multi- Purpose Feeder (MPF) Motor and Sensor Service Check” on page 2-57 .

923 “Exit System” - Cam Motor Homing failure

See “Entering CE Diagnostics Mode” on page 3-2 .

925 “Maintenance System” - Maintenance Motor Homing failure

See “Entering CE Diagnostics Mode” on page 3-2 and “Maintenance Sled Test” on page 3-33 .

928 Ink Level System - Ink Float Sensing Calibration failure

Perform “Ink Level Sensor Test” on page 3-31 .

Note: Many of the 930-938 are communication failures between the printheads and the carrier contacts as noted. If contact failures are suspected, check alignment between the pogo pins and printhead tab circuit. This can be done by lightly placing a piece of low tack tape on the printhead tab circuit and inserting it in the carrier. If contamination is suspected, remove the printhead and clean the contacts with a low-lint damp cloth. Clean the pogo pins only with a clean, lint-free cloth.

Error Symptom Action · 915 Index System · Diagnostic Information 2-5

Page 28 of the Lexmark Printer user manual — 4085-001
Page 28 · click to enlarge
Page 28

4085-001

930 Black Printhead - P-lines shorted or Substrate Heater shorted

Check all contacts and cables. If tests fail, replace the printheads. If failure still occurs, replace engine board.

Color Printheads - P-lines shorted or Substrate Heater shorted

Both Printheads - P-lines shorted or Substrate Heater shorted

931 Black Printhead - Engine cannot communicate with Printhead Memory

Check the printhead and tank contacts.Check the carrier to engine cables. Check the printhead and tank memory chip placement.

Color Printhead - Engine cannot communicate with Printhead Memory

If the problem remains, replace the engine board. See the “Engine Board / Cover Removal” on page 4-14 .

Both Printheads - Engine cannot communicate with Printhead Memory

932 Black Printhead - Contents of Printhead Memory are invalid

Replace printheads. See “Change Printheads” on page 3-4 . If contents of printhead memory are still invalid, replace engine board. See “Engine Board /Cover Removal” on page 4-14 . Check carrier cables.

Color Printhead - Contents of Printhead Memory are invalid

Both Printheads - Contents of Printhead Memory are invalid

933 Printhead System - Failure measuring a calibration resistor. The debug data identifies the resistor being measured and the type of failure: value too low, value too high, or value=zero.

Check the printhead/ carrier contacts. Try replacing the printheads before replacing the carrier. Check the carrier cable. If cable is OK, replace carrier. See “Carrier/Cable Retainer Removal” on page 4-48 . Try replacing both printheads. If problem remains, replace engine board. See “Engine Board /Cover Removal” on page 4-14 .

Error Symptom Action

Page 29 of the Lexmark Printer user manual — 4085-001
Page 29 · click to enlarge
Page 29

4085-001

934 Black Printhead - Color Printheads - Both Printheads - TSR measurement indicates a cracked / open TSR or open connection. The debug data identifies the TSR that is open.

Check the carrier/ printhead contacts. Try replacing both printheads before replacing carrier. Check the carrier cable. If cable is OK, replace carrier. See “Carrier/Cable Retainer Removal” on page 4-48 . If problem remains, replace engine board. See “Engine Board /Cover Removal” on page 4-14 .

935 Black Printhead - Color Printheads - Both Printheads - Failure measuring a TSR value. The debug data identifies the TSR being measured and the type of failure: value too low, or value too high.

Try replacing the printheads before replacing carrier. Check the carrier cable. If cable is OK, replace carrier. See “Carrier/Cable Retainer Removal” on page 4-48 . If problem remains, replace engine board. See “Engine Board /Cover Removal” on page 4-14 .

936 Service Printhead System - Failure zeroing the TSR measurement system.

Try replacing the printheads before replacing carrier. Check the carrier cable. If cable is OK, replace carrier. See “Carrier/Cable Retainer Removal” on page 4-48 . If problem remains, replace engine board. See “Engine Board /Cover Removal” on page 4-14 .

938 Printhead Thermal System error Check the printhead contacts. Overheated. Replace printhead. See “Change Printheads” on page 3-4 . If problem remains, replace carrier assembly.

Error Symptom Action · Diagnostic Information 2-7

Page 30 of the Lexmark Printer user manual — 4085-001
Page 30 · click to enlarge
Page 30

4085-001

939 RIP to Engine communications failure

Unplug and replug the AC power cord to see if the problem goes away.

Check the RIP card cable connections. If the connections are good, replace the engine board. See “Engine Board /Cover Removal” on page 4-14 . If the problem remains, replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 .

953 NVRAM Failure - NVRAM Chip failure

Replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 .

954 NVRAM Failure - NVRAM CRC failure

Replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 .

955 Code ROM error Replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 .

956 RIP Card - Processor failure Replace the RIP card. See “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 .

957 RIP ASIC failure Replace the RIP card. See “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 .

Error Symptom Action

Page 31 of the Lexmark Printer user manual — 4085-001
Page 31 · click to enlarge
Page 31

4085-001

960 RAM Memory Error - RAM soldered on the card is bad

Replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 .

980 Tray 2 Communication Error - Communication between Tray 2 and the Engine is unreliable.

Check connection between engine board and optional card.

985 Tray 2 Error Check engine to tray 2 cable and contacts.

Replace tray 2 card.

Look for PerfectFinish leaks.

Error Symptom Action · Diagnostic Information 2-9

Page 32 of the Lexmark Printer user manual — 4085-001
Page 32 · click to enlarge
Page 32

4085-001

User Status Messages

User Status Message Status Action

Ready The printer is ready to receive and process data from a host system.

Press Menu> or Menu< to take the printer offline and access the Ready Menu group. The following function may be available via the Busy/ Waiting Menu group: -Reset Printer

Press Stop to take the printer offline. The Not Ready message appears. No more data is processed from the host computer. Press Go to return the printer to the previous state.

Page 33 of the Lexmark Printer user manual — 4085-001
Page 33 · click to enlarge
Page 33

4085-001

User Status Message Status Action

Busy The printer is processing data and/ or printing pages. The Power indicator blinks while the printer is processing data.

Press Stop to take the printer offline. The Not Ready message appears. No more data is processed from the host computer; however, the printer processes all of the paper currently in motion in the printer’s paper path. Press Go to return the printer to the previous state.

-Cancel Job -Reset Printer

Diagnostic Information 2-11

Page 34 of the Lexmark Printer user manual — 4085-001
Page 34 · click to enlarge
Page 34

4085-001

User Status Message Status Action

Waiting The Waiting is displayed until the current job is terminated or until additional data is received on the active link.

Press Go to print the contents of the printer’s buffer.

Press Stop to take the printer offline. The Not Ready message appears. No more data is processed from the host computer; however, the printer processes all the paper in the printer’s paper path. Press Go to return the printer to the previous state.

Press Menu> or Menu< to access the Busy/ Waiting Menu group. The printer will be online while the Busy/Waiting Menu group is active. The following functions may be available using the Busy/Waiting Menu group: -Cancel Job -Reset Printer -Print Buffer

Page 35 of the Lexmark Printer user manual — 4085-001
Page 35 · click to enlarge
Page 35

4085-001

Warning Messages

As shown in each of the Status Screens, only one warning message can be displayed at any one time. Once the current warning condition is cleared, the printer automatically shows the next highest priority warning message. If an event occurs which causes a higher priority warning, the higher priority warning message replaces the lower priority warning message.

Panel Message Description Available on Status Screen

Supplies One or more of the printer supply items has either reached its life warning or is exhausted and/or one of the paper sources is low, empty, or missing.

  • Ready
  • Hex Trace Ready
  • Power Saver
  • Busy
  • Resolution Reduced
  • Waiting

Parallel USB

The host interface from which the printer is currently drawing and processing data.

  • Ready
  • Hex Trace Ready
  • Power Saver
  • Busy
  • Resolution Reduced
  • Waiting

Those messages which are not designated by a imply the active host interface is a standard interface.

Those messages designated by indicate the active interface is connected to the printer by PCI connector x.

Those messages designated by indicate the active interface is connected to the printer by a channel y on PCI connector x, or if x=0 on the standard network interface.

The copying message is shown when the printer is drawing and processing data originating from an OptraImage™ scanner connected to the printer by a network adapter.

Diagnostic Information 2-13

Page 36 of the Lexmark Printer user manual — 4085-001
Page 36 · click to enlarge
Page 36

4085-001

Status Messages

These messages provide the operator with information on the current state of the printer.

Status Message Status Action

The printer is being reset to activate a printer setting changed in the menus.

No buttons are active while this message is displayed.

Canceling Job Appears after the Cancel Job operation is selected. This message is displayed until the cancel operation is complete.

Press Menu> or Menu< to access the Busy/ Waiting Menu group. The printer is online while the Busy/Waiting Menu group is active.

Cleaning Printheads Appears after Cleaning Printheads is selected.

No buttons are active while this message is displayed.

Activating Menu Changes

Page 37 of the Lexmark Printer user manual — 4085-001
Page 37 · click to enlarge
Page 37

4085-001

Status Message Status Action

A representation of the operator panel when the user has modified the Menu Lockout printer setting using the Configuration Menu Group. If the Menu Lockout value is changed to On (Panel Menus=Disable), then the Disabling message is displayed. If the Menu Lockout value is changed to Off (Panel Menus=Enable), then the Enabling message is displayed.

No buttons are active while this message is displayed.

Flushing Buffer A representation of the operator panel when the printer is flushing a print job. The interpreter is flushing the currently active job until an End Of Job is found or until no data has been received on the active host interface for 5 seconds.

No buttons are active while this message is displayed.

Status Message Status Action

The printer is being reset to activate a printer setting changed in the menus.

No buttons are active while this message is displayed.

Disabling/Enabling Menus · Activating Menu Changes · Diagnostic Information 2-15

Page 38 of the Lexmark Printer user manual — 4085-001
Page 38 · click to enlarge
Page 38

4085-001

Status Message Status Action

Cancelling Job Appears after the Cancel Job operation is selected. This message is displayed until the cancel operation is complete.

Press Menu> or Menu< to access the Busy/ Waiting Menu group. The printer is online while the Busy/Waiting Menu group is active.

Cleaning Printheads Appears after Cleaning Printheads is selected.

No buttons are active while this message is displayed.

Status Message Status Action

Printer Calibrating A representation of the operator panel when the printer is initializing the mechanical sub- systems at POR (Power-On Reset), following the “Performing Self Test” message or during printing. The duration of this message varies depending on the level in the lower PerfectFinish vessel. The Stop button is available; however, the printer will post “Not Ready.” The printer will not post “Ready” until Go is pressed.

Press Menu> or Menu< to access the Busy/ Waiting Menu group for menu details. Typically this menu is used to access the Reset functions of view the printer Supplies status. The printer is online while the Busy/Waiting Menu group is active.

Page 39 of the Lexmark Printer user manual — 4085-001
Page 39 · click to enlarge
Page 39

4085-001

Status Message Status Action

Invalid Engine Code A representation of the operator panel when either the engine code has not been programmed or has been programmed but is invalid. Once this condition occurs, the Ready and Busy messages will not be displayed until valid Engine code exits. Engine code can still be downloaded to the printer when this message is on the display.

No buttons are active while this message is displayed.

Status Message Status Action

Menus Disabled Appears when the Menu> or Menu< button is pressed to access the Busy/ Waiting Menu group and all the available selections in the menu group have been disabled.

No buttons are active while this message is displayed.

Diagnostic Information 2-17

Page 40 of the Lexmark Printer user manual — 4085-001
Page 40 · click to enlarge
Page 40

4085-001

Status Message Status Action

Not Ready A representation of the operator panel when the printer is in the Not Ready state. All host links are marked as busy when the printer is Not Ready. In addition, all timeouts are stopped.

Press Go to take the printer out of the Not Ready state.

Press Menu> or Menu< to access the Busy/ Waiting Menu group. The printer is online while the Busy/Waiting Menu group is active. The following functions may be available using the Busy/ Waiting Menu group:

-Cancel Job -Reset Printer

Page 41 of the Lexmark Printer user manual — 4085-001
Page 41 · click to enlarge
Page 41

4085-001

Status Message Status Action

Performing Self Test A representation of the operator panel during Power-On Self Test (POST). When the test is complete, the printer enters the Ready state.

No buttons are active while this message is displayed.

Powering Down A representation of the operator panel during power-down cycle, after the user has turned the machine off. In the event that no errors are found, this is the last message shown before power is cut off to the RIP and engine.

No buttons are active while this message is displayed.

It is possible that an error condition could be detected that causes the printer to go into a different state. The error conditions that could cause this are:

-Paper Jams -Service Messages

Diagnostic Information 2-19

Page 42 of the Lexmark Printer user manual — 4085-001
Page 42 · click to enlarge
Page 42

4085-001

Status Message Status Action

Printing Menu Settings A representation of the operator panel when Print Menu Settings is selected from the menu. This message appears until the Print Menus page or pages are formatted and submitted to the print engine and then Busy is shown.

Press Stop to take the printer offline. The Not Ready message appears. No more data is processed from the host computer; however, the printer processes all of the paper in the printer’s paper path. Press Go to return the printer to the previous state.

Press Menu> or Menu< to access the Busy/ Waiting Menu group. The printer is online while the Busy/Waiting Menu group is active. The following functions may be available using the Busy/ Waiting Menu group:

-Cancel Job -Reset Printer

Page 43 of the Lexmark Printer user manual — 4085-001
Page 43 · click to enlarge
Page 43

4085-001

Status Message Status Action

A representation of the operator panel when Align Printheads is selected from the menu. This message appears until the Alignment page is formatted and submitted to the print engine and then Busy is shown.

Press Menu> or Menu< to access the Busy/ Waiting Menu group. The printer is online while the Busy/Waiting Menu group is active. The following functions may be available using the Busy/ Waiting Menu group:

-Cancel Job -Reset Printer

Printing Alignment Page · Diagnostic Information 2-21

Page 44 of the Lexmark Printer user manual — 4085-001
Page 44 · click to enlarge
Page 44

4085-001

Status Message Status Action

Printing Test Page A representation of the operator panel when Clean Printheads is selected from the menu. This message appears until the Clean Printheads test page is formatted and submitted to the print engine and then Busy is shown.

Press Menu> or Menu< to access the Busy/ Waiting Menu group. The printer is online while the Busy/Waiting Menu group is active. The following functions may be available using the Busy/ Waiting Menu group:

-Cancel Job -Reset Printer

Prog Engine Code DO NOT POWER OFF

A representation of the operator panel whenever new code is programmed in the engine flash. When the programming is complete, the printer returns to the Ready screen. I

No buttons are active while this message is displayed.

Page 45 of the Lexmark Printer user manual — 4085-001
Page 45 · click to enlarge
Page 45

4085-001

Status Message Status Action

A representation of the operator panel when new code is programmed in the RIP code flash. This message is shown until the programming is complete. When the programming is complete, the printer performs a Power-On Reset.

No buttons are active while this message is displayed.

Resetting Printer A representation of the operator panel during a Printer Reset. The printer resets with the Power- On Reset defaults.

No buttons are active while this message is displayed.

A representation of the operator panel after the operator has initiated one or two Factory Defaults operations.

No buttons are active while this message is displayed.

Programming System Code · Restoring Factory Defaults · Diagnostic Information 2-23

Page 46 of the Lexmark Printer user manual — 4085-001
Page 46 · click to enlarge
Page 46

4085-001

Attendance Messages

These messages are displayed when the printer is in the Operator Intervention state. The operator is provided with a description of the operator intervention condition. When an operator intervention condition occurs, all host links are notified about the intervention required condition. All timeouts are stopped while the printer is in an operator intervention state. The only exception is the PostScript Feed timeout. This timeout starts when the Load Paper message is displayed for the manual source.

Attendance Message Description Action

A Alignment = 8* A representation of the operator panel when Align Printheads is selected from the Utilities Menu and the printer is prompting the user for the “A” alignment value. A similar message is displayed for B...G alignment values.

Press Go or Return to end the alignment operation.

Enter the alignment value and press Select to continue to the next alignment value.

89 Cartridge Empty XXXX

A representation of the operator panel when cyan ink empty occurs. A similar message displays when the black, magenta, and yellow inks are empty.

This is a Type 4 error and can only be cleared by inserting a new ink cartridge. In this representation, XXXX is a placeholder for some combination of C,M,Y, and K.

Page 47 of the Lexmark Printer user manual — 4085-001
Page 47 · click to enlarge
Page 47

4085-001

Attendance Message Description Action

88 Cartridge Low XXXX

A representation of the operator panel when cyan ink low occurs and the Ink Alarm is activated. A similar message appears when the black, magenta and yellow inks are low. The XXXX is a placeholder for some combination of C,M,Y, and K.

Press Go to clear the message.

Cartridge LIfe Expired XXXX

A representation of the operator panel when an ink cartridge life expires. This means that although ink remains in the cartridge, the useful life of the cartridge is expired and the cartridge must be replaced. XXXX is a placeholder for some combination of C,M,Y, and K.

Open the cover and replace the expired ink cartridge(s).

Diagnostic Information 2-25

Page 48 of the Lexmark Printer user manual — 4085-001
Page 48 · click to enlarge
Page 48

4085-001

Attendance Message Description Action

A representation of the operator panel when the printer is requesting the operator to change the media installed in one of the input sources. The input source is displayed on line 1 and could be one of the following:

Sources equipped with both size-sensing and media-present hardware:

Load the requested size and/or paper type in the source indicated in the message. If media is present in the source and the sensed size is correct, then the printer automatically clears the message and continue the job.

Tray 1, Tray 2, MP Feeder.

If the source already contains the correct size and paper type, then press Go. This situation occurs when the user changes the media in the source, but forgets to change the paper type setting in the menus. Go is ignored if the sensed size is incorrect or media is not present in the tray.

If the requested type matches the type that is installed in the tray and the type is one of the custom types which has not been named, then only the size is displayed. One of the following sizes is left-justified on line 2:

Letter, Legal, B2, A4, Executive, Universal, A5, 7 3/4 Envelope, 9 Envelope, 10 Envelope, DL Envelope, C5 Envelope, B5 Envelope, Other Envelope

Change · Change

Page 49 of the Lexmark Printer user manual — (CONTINUED)
Page 49 · click to enlarge
Page 49

4085-001

Attendance Message Description Action

In all other cases, both the type and size are displayed on line 2. The requested type could be one of the following:

Sources equipped media- present hardware ONLY:

Load the requested size and/or type in the source indicated in the message. The printer automatically clears the message and continues the job.

(CONTINUED)

Bond, Card Stock, Coated, Colored, Envelope, Glossy, IronOn, Labels, Letterhead, Photo, Plain, Preprint, Transparency The requested size could be one of the following:

If the source already contains the correct paper size and type, press Go. This occurs when the user changes the media in the source, but forgets to change the paper size and/or paper type settings in the menus. Go is ignored if media is not present in the tray.

Letter, Legal, B5, A4, Executive, Universal, A5, 7 3/4, 9, 10, DL, C5, B5, Other

To ignore the request and print on the media installed in the tray, press Select. Some clipping may occur.

Press Menu> or Menu< to access the Busy/ Waiting Menu group. The following functions may be available using the Busy/Waiting Menu group:

-Cancel Job -Reset Printer

Change · Change · Diagnostic Information 2-27

Page 50 of the Lexmark Printer user manual — 4085-001
Page 50 · click to enlarge
Page 50

4085-001

Overriding Change Prompts

The size override function lets you override Change Prompts for any source for the remainder of a job. By overriding the prompt, the user is requesting the printer to do the following:

  • Print the page, as it is formatted, on the paper installed in the tray. Therefore, some clipping may occur. In addition, the color tables used to create the bitmap are for the requested media, not necessarily the media in the tray.
  • Do not post any further Change Paper prompts for this source for the remainder of the job. That is for subsequent pages from this source, automatically override to the size and/or type installed in the source. Note: Change Prompts is shown for other sources, unless they have been overridden for the job as well.
Page 51 of the Lexmark Printer user manual — 4085-001
Page 51 · click to enlarge
Page 51

4085-001

Attendance Message Description Action

Check Tray x Connection

A representation of the operator panel when the printer loses communications with one of the following devices:

If the device was temporarily removed or not connected properly, reattach or reconnect it. When the device is recognized, the printer automatically clears the attendance condition and continues.

-Tray 2 -Multi-Purpose Feeder

This error could occur in two ways. The specified device could have been removed from the printer (for instance, to clear a paper jam or to uninstall the device). Otherwise, the device could still be attached to the printer, but is experiencing a communications problem (Not fully connected or hardware failure).

If the device is experiencing a hardware problem, then turn the printer off and back on. If the error occurs again, then turn the printer off, remove the option, and call for service.

Check MPF Connection · Diagnostic Information 2-29

Page 52 of the Lexmark Printer user manual — 4085-001
Page 52 · click to enlarge
Page 52

4085-001

Attendance Message Description Action

A representation of the operator panel when a Long Clean is requested and the printer is asking the user if the printhead that printed the bar label “1” needs to be cleaned. A similar message is shown if the printheads associated with bars 2, 3, and 4 need to be cleaned.

Press Go if the long clean needs to be performed on the printhead represented by bar 1.

Press Stop if the long clean does not need to be performed on the printhead represented by bar 1.

Press Return to stop the cleaning operation.

Close Cover A representation of the operator panel when the printer’s upper front door is open. If the cover is open while printing, the printer continues to print, but at a lower carrier velocity.

Close the upper front door. The printer automatically clears the message and continues printing.

Clean 1? =Go/Stop

Page 53 of the Lexmark Printer user manual — 4085-001
Page 53 · click to enlarge
Page 53

4085-001

Attendance Message Description Action

31 Defective Cartridge XXXX

A representation of the operator panel when the printer detects a defective ink cartridge. In this representation, the XXX is a placeholder for some combination of C,M,Y, and K. The defective cartridge is identified in the XXXX string.

Open the cover and replace the defective ink cartridge(s). The carrier appears at the ink cartridge change location.

Press and hold Select, and then press Return to display debug data for the engine microcode and the applicable smart options. The service engineer should use this function to help diagnose the problem.

The engine firmware was either unable to communicate with the ink cartridge EEPROM or the ink cartridge EEPROM was corrupted. This could be the case if the ink cartridge has a missing or defective smart chip.

1. Try POR. 2. Remove and reinstall the defective cartridge. 3. Inspect pogo pins for damage.

Diagnostic Information 2-31

Page 54 of the Lexmark Printer user manual — 4085-001
Page 54 · click to enlarge
Page 54

4085-001

Attendance Message Description Action

54 Std Par ENA Connect Lost

A representation of the operator panel when the printer detects during its power-on cycle that the connection to an External Network Adapter has been lost. Once a connection is initially established, a printer setting is modified to note a connection exists. Then, each time the power is cycled on, if the setting states a connection exists, the printer attempts to communicate with the adapter. If the adapter does not respond, this message is shown.

Press Go to clear the message. The printer clears the setting stating an external network adapter connection exists and restarts.

Page 55 of the Lexmark Printer user manual — 4085-001
Page 55 · click to enlarge
Page 55

4085-001

Attendance Message Description Action

81 Engine Code CRC Failure

A representation of the operator panel when microcode to be programmed in the engine flash code module has failed a CRC check.

Press Go to clear the message. The microcode data is discarded and must be re-transmitted from the host computer.

Flushing Buffer A representation of the operator panel when the printer is flushing a print job. The interpreter is flushing the currently active job until an End Of Job is found or until no data has been received on the active host interface for 5 seconds.

No buttons are active while this message is displayed.

This message is commonly displayed when the Lexgear interpreter receives a print job with data corruption. It can also be displayed when a print job is sent to the printer in PostScript or PCL 5 emulations.

Diagnostic Information 2-33

Page 56 of the Lexmark Printer user manual — 4085-001
Page 56 · click to enlarge
Page 56

4085-001

Attendance Message Description Action

56 Std Parallel Port Disabled

A representation of the operator panel when data is sent to the printer across a parallel port, but the parallel port is disabled.

Press Go to clear the message. The printer discards any data received on the parallel port. Enable the parallel port.

Press Menu> or Menu< to access the Busy/ Waiting Menu group. The following function may be available using the Busy/ Waiting Menu group:

Once the error has been displayed for the first time, reporting of further errors is suppressed until the menus are entered, or the printer is reset.

Insert Duplex Pages & Press Go

A representation of the operator panel when a manual duplex job has been sent to the printer and the printer has completed printing the front sides of the pages. The user should remove the manual duplex sheets and reinsert them (face up) into tray 1.

Reinsert pages into tray 1 (face up) and press Go to continue printing the back sides.

-Reset Printer

Page 57 of the Lexmark Printer user manual — 4085-001
Page 57 · click to enlarge
Page 57

4085-001

Attendance Message Description Action

Load

A representation of the operator panel when the indicated source is out of media. The input source is displayed on line 1 and could be one of the following:

Sources equipped with both size-sensing and media-present hardware:

Load

Load the requested size and/or paper type in the source indicated in the message. If media is present in the source and the sensed size is correct, then the printer automatically clears the message and continues the job.

Tray 1, Tray 2, MP Feeder.

One of the following items is shown on line 2:

Sources equipped media- present hardware ONLY:

In all cases, both the type and size are displayed on line 2. The requested type could be one of the following:

Load the requested size and/or type in the source indicated in the message. The printer automatically clears the message and continues the job.

Bond, Card Stock, Coated, Colored, Envelope, Glossy, IronOn, Labels, Letterhead, Photo, Plain Preprint, Transparency The requested size could be one of the following:

Press Go to request that the printer check the sources again for the prompted size and type.

Press Menu> or Menu< to access the Busy/ Waiting Menu group. The following functions may be available using the Busy/Waiting Menu group: -Cancel Job -Reset Printer

Letter, Legal, B5, A4, Executive, Universal, A5, 7 3/4, 9, 10, DL, C5, B5, Other

Diagnostic Information 2-35

Page 58 of the Lexmark Printer user manual — 4085-001
Page 58 · click to enlarge
Page 58

4085-001

Attendance Message Description Action

A representation of the operator panel when the printer receives a request to manually feed paper or envelopes in the Manual Slot or MP Feeder. The request may have come through a print job or from the operator panel.

If no media exists in the Manual Slot or MP Feeder, then manually feed a sheet. The printer automatically clears the message and continues the job.

One of the following items is shown on line 2. In all cases, both the type and size are displayed on line 2. The requested type could be one of the following:

If the MP Feeder is installed and if the correct media is already present in the MP Feeder, then press Go. The printer clears the message and continues the job.

Bond, Card Stock, Coated, Colored, Envelope,Glossy, IronOn, Labels, Letterhead, Photo, Plain, Preprint, Transparency The requested size could be one of the following:

Letter, Legal, B5, A4, Executive, Universal, A5, 7 3/4, 9, 10, DL, C5, B5, Other

Load Manual · Load Manual

Page 59 of the Lexmark Printer user manual — (CONTINUED)
Page 59 · click to enlarge
Page 59

4085-001

Attendance Message Description Action

To request the printer to pick the sheet from an automatic source, press Select.

Press Menu> or Menu> to access the Busy/ Waiting Menu group. The following functions may be available using the Busy/Waiting Menu group:

(CONTINUED)

-Cancel Job -Reset Printer

Load Manual · Load Manual · Diagnostic Information 2-37

Page 60 of the Lexmark Printer user manual — 4085-001
Page 60 · click to enlarge
Page 60

4085-001

Attendance Message Description Action

31 Missing Cartridge XXXX

A representation of the operator panel when the printer detects a missing ink cartridge. In this representation, XXXX is a placeholder for some combination of C,M,Y, and K. The missing ink cartridge(s) is identified in the XXXX string.

Open the cover and insert an ink cartridge where an ink cartridge is missing.

Press and hold Select and then press Return to display debug data for the engine microcode and the applicable smart options.

1. POR. 2. Reinstall the missing cartridge or remove and reinstall a cartridge that is already in place. 3. Check for bent or damaged ink tank pogo pins. 4. This message will be posted if the carrier handle stalls against the covers while printing. Ensure that the carrier handle snaps into the detents.
Page 61 of the Lexmark Printer user manual — 4085-001
Page 61 · click to enlarge
Page 61

4085-001

Attendance Message Description Action

31 Missing Printhead XXXX

A representation of the operator panel when the printer detects a missing printhead. In this representation, XXXX is a placeholder for either: YMC,K or YMCK. The missing printhead(s) are identified in the XXXX string.

Check printhead to carrier contacts.

Open the cover and replace the defective printhead.

Press and hold Select and then press Return to display debug data for the engine microcode and the applicable smart options.

Open Cover A representation of the operator panel when the user has requested an ink cartridge change or a printhead change.

Open the door and change the supply item.

Press Go or Return to cancel the operation.

38 Memory Full A representation of the operator panel when the printer is processing an incoming job and there is not enough memory available to continue processing the job.

Press Go to clear the message and continue processing the job. Some data loss occurs. Determine how to make more memory available to your print job:

  • Delete fonts, macros, and other data in RAM.
  • Simplify your print job.
  • Install additional memory. Press Menu> or Menu< to access the Busy/ Waiting Menu group. The following functions may be available using the Busy Waiting Menu group:

-Cancel Job -Reset Printer

Diagnostic Information 2-39

Page 62 of the Lexmark Printer user manual — 203 Paper Jam (Printer Input Sensor)
Page 62 · click to enlarge
Page 62

4085-001

Paper Jams

Multiple paper jam messages exist for this printer. Most paper jam messages have a unique error number. Each message also instructs the customer what action to take to resolve the jam or where in the printer to look to find the jammed paper.

The following actions can be taken while this message is displayed:

  • Once all the jammed pages are cleared from the paper path, press Go to resume printing.
  • Press and hold Select and then press Return to display debug data for the engine microcode and the applicable smart options. The service engineer should use this function to help diagnose the problem. The Customer Support Center may request the user to complete this function as well. Note: Press Menu> to perform a “jog” function to help free the jammed sheet. This applies to the following paper jams:

200 Paper Jam (Printer Staging Sensor)

Paper is jammed prior to the printer staging sensor. Remove tray 1 and clear the jam.

201 Paper Jam (Printer Input Roller Sensor)

Paper is jammed prior to the printer input roller sensor (non- PerfectFinish path). Remove tray 1 and clear the jam.

203 Paper Jam (Printer Input Sensor)

Paper is jammed over the input sensor. Open the cover and clear the jam.

Page 63 of the Lexmark Printer user manual — 222 Paper Jam -Tray 2
Page 63 · click to enlarge
Page 63

4085-001

204 Paper Jam (Printer Staging Sensor)

Paper is jammed over the staging sensor. Open the cover and clear the jam.

205 Paper Jam (Printer Input Roller Sensor)

Paper is jammed prior to the printer input roller sensor (PerfectFinish path). Open the cover and clear the jam.

206 Paper Jam (Fail to make Input Roller Sensor - Non PerfectFinish)

Paper is jammed prior to the printer input roller sensor (non PerfectFinish path). Check Tray 2.

207 Paper Jam (Fail to make Input Roller Sensor - PerfectFinish)

Paper is jammed prior to the printer input roller sensor (PerfectFinish path).

208 Paper Jam (Fail to make Staging Sensor - Tray 2 (PerfectFinish)

Paper is jammed prior to the staging sensor (PerfectFinish).

209 Paper Jam (Printer Input Roller Sensor)

Paper is jammed prior to the printer input roller sensor. Remove tray 1 and clear the jam.

220 Paper Jam -Tray 2

Paper was picked from tray 2 but did not arrive at the feed sensor in tray 2.

221 Paper Jam -Tray 2

Paper was picked from tray 2 and is jammed over the feed sensor in tray 2.

222 Paper Jam -Tray 2

Paper is jammed in tray 2.

Diagnostic Information 2-41

Page 64 of the Lexmark Printer user manual — 251 Paper Jam (MPF)
Page 64 · click to enlarge
Page 64

4085-001

250 Paper Jam (MPF)

Paper was picked from the MPF but did not arrive at the input roller sensor.

251 Paper Jam (MPF)

Paper was picked from the MPF but did not arrive at the input roller sensor.

Page 65 of the Lexmark Printer user manual — Short Paper
Page 65 · click to enlarge
Page 65

4085-001

PerfectFinish Empty

The above is a representation of the operator panel when PerfectFinish empty occurs. This message indicates that the supply item must be replaced.

The following actions can be taken while this message is displayed:

  • Press Go to clear the message and override the message. For the rest of the current job, the printer prints without PerfectFinish. The message appears again at the beginning of every subsequent job until the empty condition is cleared.
  • Replace the PerfectFinish supply item. Press Go to clear the message and override the message.

Short Paper

The above is a representation of the operator panel when the paper length is too short to print the data as formatted.

This error can only occur when the printer does not know the actual paper size that is loaded in a tray. If the tray has auto-size capabilities, then the paper stop could be in the wrong position. If the tray is not capable of auto-size sensing, then the operator may have entered the wrong size in the paper size menu.

The following actions can be taken while this message is displayed:

  • Press Go to clear the error and continue printing pages.
  • Press Menu> or Menu< to access the Busy/Waiting Menu group. The following functions may be available using the Busy/ Waiting Menu
Show 5 more labels / short text on this page
87 PerfectFinish · Empty · 34 Short Paper · – Cancel Job · Diagnostic Information 2-43
Page 66 of the Lexmark Printer user manual — Unsupported Printhead
Page 66 · click to enlarge
Page 66

4085-001

– Reset Printer Note: Menu Lockout does not prevent access to the Busy/Waiting Menu group.

Unsupported Ink Cartridge

The above is a representation of the operator panel when the top cover is closed and an unsupported ink cartridge is detected (for example, the software keys of the printer and ink cartridge do not match). It may take the printer several seconds to determine if the ink cartridge is supported. XXXX indicates which of the C, M, Y or K ink cartridges are unsupported.

The following actions can be taken while this message is displayed:

  • Remove the unsupported ink cartridge. See “Change Ink Cartridges” on page 3-4 .

Unsupported Printhead

The above is a representation of the operator panel when the top cover is closed and an unsupported printhead is detected (for example, the software keys of the printer and printhead do not match). It may take the printer several seconds to determine if a print head is supported. XX indicates which of the K or C(MY) printheads are unsupported.

The following actions can be taken while this message is displayed:

Remove the unsupported printhead. See “Change Printheads” on page 3-4 .

Show 4 more labels / short text on this page
32 Unsupported · Cartridge XXXX · 32 Unsupported · Printhead XX
Page 67 of the Lexmark Printer user manual — 4085-001
Page 67 · click to enlarge
Page 67

4085-001

Error Recovery from Attendance Conditions

The following table indicates how the printer acts when each of the attendance/error conditions occurs. Attendance conditions can be categorized into these distinct groups:

  • Type 1 - When a Type 1 condition occurs during a job, the printer finishes printing all pages in the paper path. Furthermore, it may pick a few additional pages if they had already been committed to be printed. Depending on the specific condition, some data loss may occur on the pages. See “Error Recovery from Attendance Conditions” on page 2-45 . Once the pages are printed, the printer displays the attendance message. After the condition is cleared, the printer resumes printing the next page in sequence. In other words, none of the pages printed before the attendance message will be reprinted.
  • Type 2 - When a Type 2 condition occurs during a job, the printer finishes printing all pages in the paper path before displaying the attendance message. After the condition is cleared, the printer resumes printing the next page in sequence. In other words, none of the pages printed before the attendance message will be reprinted.
  • Type 3 - When a Type 3 condition occurs, the printer immediately stops and an attendance message is displayed. All pages in the paper path must be manually cleared by the user. After the condition is cleared, the printer resumes printing the pages that were left in the paper path.

Diagnostic Information 2-45

Page 68 of the Lexmark Printer user manual — 4085-001
Page 68 · click to enlarge
Page 68

4085-001

Error Recovery from Attendance Conditions

Sound Alarm (if Enabled)

Attendance Condition Error Type

A Alignment Type 1 No No

Cartridge Life Expired Type 1 No Yes

Cartridge Life Warning Type 1 No Yes

Type 1 No Yes

Change

Clean X? Go/Stop Type 1 No No

Type 2 No Yes

Load

Type 2 No Yes

Load Manual

Insert Duplex Pages & Press Go Type 1 No Yes

Close Cover a N/A N/A N/A

Open Cover Type 1 No No

Check Tray x Connection Type 3 No No

Install Tray x or Cancel Job Type 3 No Yes

31 Defective Ink Cartridge Type 1 No Yes

31 Missing Ink Cartridge Type 1 No Yes

31 Missing Printhead Type 1 No Yes

32 Unsupported Print Head Type 1 No Yes

32 Unsupported Cartridge Type 1 No Yes

34 Short Paper Type 1 b Yes Yes

38 Memory Full Type 1 b Yes Yes

54 Std Par ENA Connection Lost Type 1 Yes Yes

56 Std Parallel Port Disabled Type 1 b Yes Yes

Show 4 more labels / short text on this page
Auto Continue Available · Change <src> <size> · Load <src> <size> · Load Manual <size>
Page 69 of the Lexmark Printer user manual — 4085-001
Page 69 · click to enlarge
Page 69

4085-001

Sound Alarm (if Enabled)

Attendance Condition Error Type

81 Engine Code CRC Failure Type 1 No Yes

87 PerfectFinish Empty Type 1 No Yes

88 Cartridge Low Type 1 Yes Yes (Ink Low Alarm)

89 Cartridge Empty Type 2 No Yes

200 Paper Jam Check Tray 1

Type 3 No Yes

201 Paper Jam Check Tray 1

203 Paper Jam Open Cover

204 Paper Jam Open Cover

205 Paper Jam Check Tray 1

206 Paper Jam Check Tray 2

207 Paper Jam Check Tray 2

208 Paper Jam Check Tray 2

209 Paper Jam Check Tray 1

220 Paper Jam Check Tray 2

221 Paper Jam Check Tray 2

222 Paper Jam Check Tray 2

250 Paper Jam Check MPF

251 Paper Jam Check MPF

aThe printer continues to print (if it was printing) when the cover is open. However the carrier moves at a lower velocity.

bExpect data loss when this condition occurs.

Auto Continue Available · Diagnostic Information 2-47

Page 70 of the Lexmark Printer user manual — 4085-001
Page 70 · click to enlarge
Page 70

4085-001

Power-On Self Test (POST) Sequence

1. Turn on power switch. 2. The operator panel displays one row of rectangles followed by two rows of diamonds. 3. The printer indicator (green light) comes on. 4. “Performing Self Test” is displayed on the operator panel and then turns off. 5. The maintenance motor cycles and then stop. 6. The index motor cycles and then stops. 7. The printer indicator (green light) stays on. 8. Ready is displayed indicating that POST is complete.

If your printer completes POST with no errors, go to the “Symptom Tables” on page 2-50 . Locate the symptom and take the indicated action.

If your printer does not complete POST, locate the symptom in the following table and take the indicated action.

Page 71 of the Lexmark Printer user manual — 4085-001
Page 71 · click to enlarge
Page 71

4085-001

Post Symptom Table

Blank display, carrier moves, paperfeed motor turns

See the “Operator Panel (LCD) Display Service Check” on page 2-59 .

All diamonds on display See the “Operator Panel (LCD) Display Service Check” on page 2-59 .

Performing Self Test remains on display, no motors turn

See the “Power Supply Service Check” on page 2-63 .

Index motor does not turn See the “Index Motor Service Check” on page 2-56 .

Maintenance motor does not turn See the “Maintenance Station Service Checks” on page 2-55 .

Carrier drives into side frame See the “Carrier System Test” on page 3-32 . If carrier system test fails, replace the carrier assembly.

Printer indicator light does not come on or fails to stay on

See the “Operator Panel (LCD) Display Service Check” on page 2-59 .

POST is incomplete, printer indicator light is on, no motors turn and performing self-test is displayed

See the “Power Supply Service Check” on page 2-63 .

Printer inoperable See the “Power Supply Service Check” on page 2-63 .

Symptom Action · Diagnostic Information 2-49

Page 72 of the Lexmark Printer user manual — Maintenance Station Problems
Page 72 · click to enlarge
Page 72

4085-001

Symptom Tables

Locate the symptom in the following tables and take the appropriate action.

Carrier Transport Problems

  • No carrier movement
  • Slow carrier movement
  • Carrier stops
  • Carrier does not move to cartridge load position when opening access door
  • Carrier strikes left side frame. See page 2-48.

See the “Transport Service Check” on page 2-67 .

See the “Carrier System Test” on page 3-32 .

Communications Problems

Printer not communicating with host computer

See the “Parallel Wrap Test” on page 3-25 .

Not able to print test page Check the USB cable and engine board cable connection. If okay, replace RIP card.

Maintenance Station Problems

  • Fails to cap the printhead
  • Fails to clean the printhead
  • Pump fails to work
  • Maintenance assembly does not move
  • Maintenance assembly moves to forward position, then will not return
  • Access door switch does not work
  • Peristalic pump or motor does not work.

See the “Maintenance Station Service Checks” on page 2-55 .

See the “Maintenance Sled Test” on page 3-33 .

Symptom Action · Symptom Action · Symptom Action

Page 73 of the Lexmark Printer user manual — Power Problems
Page 73 · click to enlarge
Page 73

4085-001

Operator Panel Problems

Printer indicator light does not:

See the “Operator Panel (LCD) Display Service Check” on page 2-59 .

  • Turn on
  • Flash
  • Turn off
  • All diamonds

One or two pels missing Replace the operator panel assembly.

Only one button inoperative Replace the operator panel assembly.

More than one button inoperative See the “Operator Panel (Buttons) Service Check” on page 2-58 .

All diamonds on display See the “Operator Panel (LCD) Display Service Check” on page 2-59 .

Paper Feed Problems

Paper fails to stop at first print line

See the “Paper Feed Service Check” on page 2-60 .

  • Fails to pick paper
  • Picks more than one sheet of paper
  • Picks paper but fails to feed
  • Paper jams
  • Paper fails to exit
  • Noisy paper feed
  • Paper skews
  • Paper does not feed, motor does not turn
  • Paper does not feed - motor attempts to turn

See “Paper feed pick assembly does not feed, paper feed pick motor does not turn” on page 2-61 .

Power Problems

Printer inoperable See the “Power Supply Service Check” on page 2-63 .

Show 4 more labels / short text on this page
Symptom Action · Symptom Action · Symptom Action · Diagnostic Information 2-51
Page 74 of the Lexmark Printer user manual — 4085-001
Page 74 · click to enlarge
Page 74

4085-001

Print Quality Problems

  • Voids in characters
  • Light print
  • Prints off the page
  • Fuzzy print
  • Carrier moves but does not print
  • Printhead drying prematurely
  • Vertical alignment off
  • Excessive ink flow (flooding)
  • Horizontal banding

See the “Print Quality Service Check” on page 2-65 .

  • Ink smearing
  • Vertical streaks on paper
  • Print lines crowded

See the “Paper Feed Service Check” on page 2-60 .

Symptom Action

Page 75 of the Lexmark Printer user manual — 4085-001
Page 75 · click to enlarge
Page 75

4085-001

Service Checks

Maintenance Functions

The maintenance station’s function is to maintain the printhead jetting over the life of the head. It also manages the waste ink used during the nozzle spitting maintenance routine. Most functional parts (except motor, pump and drivetrain) are mounted on a maintenance carrier that is driven front to back in the printer. This action is perpendicular to the printhead movement. The maintenance carrier moves to positions that actuate the various maintenance functions. These functions include: capping, wiping, spitting, purging and wet wiping. The maintenance carrier moves in concert with the printheads to accomplish the maintenance routines.

Cap The maintenance station caps and protects the printheads from drying and subsequent failure of the nozzles for up to six months. The customer may be required to initiate a “clean printhead” routing to fully recover dried or clogged nozzles following a six-month capping period. A clean printhead test page will be incorporated into this function to allow the customer to qualify print quality before and after the nozzle recovery procedure. The caps should last the 100K page life of the printer.

Wipe The maintenance station wipes the nozzle plates to remove ink buildup and debris. Following the wipe function, a jetting function is performed to completely recover the nozzles from any debris left by the wiping process.

Spit The maintenance station provides an area (bottle) to collect the ink from the jetting function of the printheads. This area also serves to minimize mist creation and promotes evaporation of the ink.

Purge The maintenance station provides a purging function to remove bubbles and soft plugs that clog the printhead nozzles. Customer initiated purge is available in the “long clean” operation initiated from the operator panel.

Function Description · Diagnostic Information 2-53

Page 76 of the Lexmark Printer user manual — 4085-001
Page 76 · click to enlarge
Page 76

4085-001

Wet Wipe The maintenance station applies a cleaning solvent to the edge of the printhead that will be wiped across the entire bottom surface of the printhead. This will occur several time during the life of the printhead to facilitate the removal of ink debris. This solvent also serves to lubricate the wipers to reduce wear and prevent ink from drying on the wiper edge, which can reduce wiper efficiency.

The maintenance station will collect the waste ink in a container (bottle) with sufficient volume for the 100,000 page life of the printer. The container will provide spill protection for a 15-degree tilt at maximum waste volume.

Function Description · Maintenance Sump Capacity

Page 77 of the Lexmark Printer user manual — 4085-001
Page 77 · click to enlarge
Page 77

4085-001

Maintenance Station Service Checks

1 Maintenance Station Assembly

The maintenance carrier is driven in a front to rear motion by the maintenance stepper motor. A homing sensor is provided at the rear of the maintenance station to home the maintenance carrier during power up. Engine code software controls the step count from the home position to the various positions the maintenance carrier must move to accomplish the various maintenance tasks on the printheads. Utilizing cams and linkages, the various components on the maintenance carrier are actuated by the carrier motion.

Check the maintenance carrier moves through its complete forward to back motion without binds.

Check the maintenance station for worn, broken or dislodged parts.

Check that the maintenance sensor is snapped securely into the maintenance station frame.

2 Maintenance Motor Assembly

Check for approximately +1.8 V dc at pins 1, 2, 3, and 4 on connector (J3) on the engine board. If voltage is incorrect, replace the engine board. If voltage is correct, check connector and voltage at the motor. Check for a short in motor and for binds. If a short or bind is found, replace the motor.

3 Peristalic Pump Check the hose connections. If okay, replace the pump. See “Peristaltic Pump Removal” on page 4-49 .

4 Maintenance Homing Sensor

If the access door switch does not work or carrier does not move, check (J3) connector pin number 7 for approximately +5 V. If voltage is correct, check connection at the sensor. If connection is good, replace sensor. See “Maintenance Sled Test” on page 3-33 .

5 Wiper A worn wiper can cause degraded print quality just after a maintenance cleaning. Check for a loose or worn wiper.

6 Cap A worn cap can cause the printhead nozzles to dry and clog. Check for a loose or worn cap.

FRU Action · Diagnostic Information 2-55

Page 78 of the Lexmark Printer user manual — Table of Contents
Page 78 · Contents
Contents

Contents

Prefacep.71. General Informationp.13Power Consumptionp.13Internal Power Supply Specificationsp.14Maintenance Approachp.14Tools Required For Servicep.15Abbreviationsp.15Operator Panel and Menusp.16Using the Operator Panelp.16Power Indicator Statesp.16Operator Panel Button Functionsp.17Printer Messagesp.18Operator Panel Menusp.19Printing the Menu Settings Pagep.20Changing Printer Settingsp.21Disabling the Operator Panel Menusp.222. Diagnostic Informationp.23Startp.23Service Messagesp.24Error Indicator Tablep.25User Status Messagesp.32Warning Messagesp.35Status Messagesp.36Attendance Messagesp.46Overriding Change Promptsp.50Paper Jamsp.62Power-On Self Test (POST) Sequencep.70Post Symptom Tablep.71Symptom Tablesp.72Service Checksp.75Maintenance Functionsp.75Maintenance Station Service Checksp.77Index Motor Service Checkp.78Sensor Checksp.78Multi-Purpose Feeder (MPF) Motor and Sensor Service Checkp.79Operator Panel (Buttons) Service Checkp.80Operator Panel (LCD) Display Service Checkp.81Options Service Checkp.81Paper Feed Service Checkp.82Power Supply Service Checkp.85RIP Card Service Checkp.86Print Quality Service Checkp.87Index Card/Sensor Service Checkp.89Transport Service Checkp.89Cam System Motor/Sensor Service Checkp.91User Error Messagesp.913. Diagnostic Aidsp.95Printer Operationsp.95Operations Initiated by Pressing Buttons at Power-On Resetp.95Change Ink Cartridgesp.98Change Printheadsp.98Aligning the Printheadsp.99Cleaning Printheadsp.101Linking Input Traysp.102Unsolicited Manual Feedp.104Manual Duplexp.104Printing Menu Settings Pagep.104Restoring Factory Defaultsp.106Canceling a Print Job using the Operator Panelp.106Resetting the Printer using the Operator Panelp.108Other Resetsp.111Activating Hex Trace Debug Modep.113Diagnostics (Mode 1) - Print Testsp.113Diagnostics (Mode 2) - Hardware Testsp.116Diagnostics (Mode 2) - Input Tray Testsp.121Diagnostics (Mode 2) - Base Sensor Testsp.123Diagnostics (Mode 2) - Subsystem Testsp.125Diagnostics (Mode 2) - Supplies Testsp.128Diagnostics (Mode 2) - Printer Setupp.129Diagnostics (Mode 2) - Error Logp.131Menusp.133Understanding the Menu Display and Menu Buttonsp.133Example of Modifying a Printer Setting Using the Operator Panelp.136Operator Panel Menu Definitionp.138Busy/Waiting Menu Groupp.139Job Menup.140Ready Menu Groupp.142Configuration Menu Groupp.154Diagnostics Menu Group (Mode 1: Printing)p.156Diagnostics Menu Group (Mode 2: Non-printing)p.1574. Repair Informationp.161Handling ESD-Sensitive Partsp.161Adjustmentsp.162Removal Proceduresp.162Releasing Plastic Latchesp.162Rear Cover Removalp.163Operator Panel Cover/Operator Panel Removalp.165Exit Tray Removalp.165Left Frame Cover Removalp.166Left Cover Removalp.167Right Cover/Power Switch Removalp.169Left Tray Cover Removalp.171Right Tray Cover Removalp.172Ink Levels and Temperature Sensor with Bracket Removalp.173Engine Board /Cover Removalp.174Carrier with Card Removalp.175Carrier 1st Stage Drive Belt Removalp.177Carrier Printhead Latch Removalp.177Multi-Purpose Feeder (MPF) Motor and Sensor Removalp.177Power Supply Removalp.179Pump Housing/Maintenance Station/Ink Waste Tank/ Transport Carrier Motor Removalp.180Index Card Assembly Removalp.182Cover-Open Sensor Removalp.183RIP-EMC Shield Assembly/RIP Card Removalp.184PerfectFinish Sensor Assembly/Rear Paper Path Sensor Removalp.186Frame From Base Removalp.187Cam Engine Motor with Gear Removalp.189Paper Feed Pick Arm Assembly with Motor and Paper Path Sensor Removalp.191PerfectFinish Gear Plate Removalp.192PerfectFinish Motor Removalp.193Index Motor Assembly Removalp.193Encoder Disk Feed Roller Assembly Removalp.194Star Wheel Shaft Assembly Removalp.196Paper Feed Platen Assembly Removalp.198Exit Shaft with Gear Removalp.199Paper Feed Frame and Motor/Cam Shaft Assembly Removalp.200Left Index Frame Pivot Assembly Removalp.203Right Index Frame Pivot Assembly Removalp.205Bat Wings and Bushings Removalp.206Backup Roller Assembly Removalp.207Backup Roller Spring Removalp.208Carrier/Cable Retainer Removalp.208Peristaltic Pump Removalp.209Tray 2 Covers Removalp.209Tray 2 Paper Pick Arm Assembly Removalp.210Tray 2 Paper Feed Motor and Card Assembly Removalp.2125. Connector Locationsp.213Engine Boardp.213RIP Cardp.214RIP Card (cont.)p.215Optional Tray 2p.2166. Preventive Maintenancep.217Lubrication Specificationsp.2177. Parts Catalogp.219How To Use The Parts Catalogp.219Bp.245Cp.245Dp.245Ep.245Hp.245Ip.245Jp.245Lp.245Mp.245Op.245Pp.245Rp.246Sp.246Tp.247Up.247Wp.247Part Numbersp.247Indexp.245
Page 79 of the Lexmark Printer user manual — Top view of the multi-purpose feeder connector pin numbers:
Page 79 · click to enlarge
Page 79

4085-001

Multi-Purpose Feeder (MPF) Motor and Sensor Service Check

1. Remove the rear cover from the printer. 2. Remove the engine board cover. 3. Install the multi-purpose feeder. 4. Check for a voltage reading at connector (J10) pin 1 for approximately +36 V dc on the engine board. If the voltage is incorrect, replace the engine board. If the voltage is correct, go to step 5. 5. Remove the feeder from the printer. 6. Remove the left cover. 7. To check the motor, check between pins 1 and 5 on the motor connector for approximately 16.8 ohms. If the reading is incorrect, replace the multi-purpose feeder motor. If the reading is correct, check the continuity between each pin 1 and 5 to the motor case. If continuity exists, replace the motor. If the symptom remains, go to “Power Supply Service Check” on page 2-63 . To check the sensor, check pins 7 and 8 to ground at connector (J10) for a voltage reading of approximately 5 V dc each, with MPF installed and power on. If the voltage is incorrect, replace the engine board. If the voltage is correct, remove the multi-purpose feeder and check between the motor connector pins 4 and 8 with the negative meter lead on pin 4 and positive lead on pin 8. Check for a reading of approximately 3.7 ohm. If ohm reading is not correct, replace sensor. See “MP Feeder Sensor Test” on page 3-28 .

Top view of the multi-purpose feeder connector pin numbers:

Diagnostic Information 2-57

Page 80 of the Lexmark Printer user manual — 4085-001
Page 80 · click to enlarge
Page 80

4085-001

Operator Panel (Buttons) Service Check

1 Operator Panel Assembly

If any button fails the button test, replace the operator panel assembly. See “Button Test” on page 3-23 .

With the operator panel connected to the engine board, be sure the voltage at (J4) pins 1, 2, 3 and 5 measures +5 V dc. If the voltage is incorrect, replace the engine board. If the voltage is correct, check the continuity of the operator panel cable. Replace the operator panel cable if continuity is incorrect. If correct, replace the operator panel assembly.

FRU Action · 2 Engine Board · Operator Panel Assembly

Page 81 of the Lexmark Printer user manual — DRAM Memory Option(s)
Page 81 · click to enlarge
Page 81

4085-001

Operator Panel (LCD) Display Service Check

  • Operator panel display blank - printer indicator light Off, paper feed motor turns, carrier moves.
  • Operator panel display blank - printer indicator light On.

1 Engine Board Disconnect connector (J4) from the engine board and verify the voltage at approximately +9 V dc at pins 1, 2, 3 and 5. If the voltage is correct, replace the operator panel. If incorrect, replace the engine board.

2 LCD To check LCD, see “LCD Hardware Test” on page 3-22 .

Options Service Check

DRAM Memory Option(s)

This service check is the same as the flash memory option service check. Run the “DRAM Memory Test” on page 3-23 . If the test fails, replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 .

FRU Action · Diagnostic Information 2-59

Page 82 of the Lexmark Printer user manual — If you are experiencing a paper jam:
Page 82 · click to enlarge
Page 82

4085-001

Paper Feed Service Check

If you are experiencing a paper jam:

1. Check the 200 error code paper jams. See “Paper Jams” on page 2-40 . 2. Check the entire paper path for obstructions. 3. Be sure the input tray contains not more than 150 sheets of paper and the manual tray not more than 100. 4. Be sure the correct type of paper is being used. 5. Check for static in the paper. 6. Ensure the correct position of the left paper adjuster guide assembly.

1 Gears Check for binds in the gear train and paper feed mechanism by rotating the large feed roll by hand.

Check all gears for correct installation and signs of wear or damage. If there is a bind, isolate it by removing one of the small idler gears on the inside of the left side frame. Replace any worn or binding gears or rollers.

2 Paper Path See “Paper Jams” on page 2-40 .

FRU Action

Page 83 of the Lexmark Printer user manual — 4085-001
Page 83 · click to enlarge
Page 83

4085-001

Paper feed pick assembly does not feed, paper feed pick motor does not turn

  • A defective motor
  • A bind in the paper feed mechanism
  • Defective gears
  • Defective engine board
  • Defective power supply

1 Power Supply Check the power supply. See the “Power Supply Service Check” on page 2-63 . If the power supply voltage is incorrect, replace the power supply.

2 Engine Board Disconnect (J6) from the engine board. With the power on, check the voltage between pins 6, 10, and ground. The voltage at pin 6 should be approximately +35 V dc. The voltage at pin 10 should be approximately +5 V dc. If either of these readings are incorrect, replace the engine board. Check continuity between (J2) on the RIP card and (J14) on the engine board. If correct, replace the engine board. If incorrect, go to step 3.

3 Paper Feed Pick Motor

Disconnect (J6). Check between 6 and 7 on the connector for approximately 27.8 ohms. If reading is incorrect, replace the paper feed pick motor assembly. If reading is correct, check the continuity between each 6 and 7 to the motor case. If continuity exists, replace the paper feed pick motor assembly.

Check the index motor connector J16 pin 2 to ground for approximately 27 volts. If voltage is incorrect, replace the system board. If reading is correct, check the continuity. See “Index Motor Service Check” on page 2-56 . If symptom remains, go to step 4.

4 Tray 1 Sensor Check

See “Tray 1 Sensor Test” on page 3-27 . If test fails, replace sensor.

FRU Action · Index Motor · Diagnostic Information 2-61

Page 84 of the Lexmark Printer user manual — 4085-001
Page 84 · click to enlarge
Page 84

4085-001

5 RIP Card Cable Check the continuity of the RIP card cable. If incorrect, replace the cable. If correct, replace the RIP card.

Optional tray 2 paper feed pick assembly does not feed, paper feed pick motor does not turn

  • A defective motor
  • A bind in the paper feed mechanism
  • Defective gears
  • Defective engine board
  • Defective power supply (+62 V dc)

1 Power Supply Check the power supply. See the “Power Supply Service Check” on page 2-63 . If the power supply voltage is incorrect, replace the power supply. Check the position of tray 2 to insure that the paper port connectors are attached correctly.

2 Tray 2 Card With the power on, check for the following readings: (J4) pin 1 to ground = 35 V dc (J4) pin 3 to ground = 5 V dc (J4) pin 5 to ground = 5 V dc (J4) pin 7 to ground = 5 V dc

If voltage is incorrect, check the engine board and replace if needed. If voltage is correct, go to step 3.

FRU Action · FRU Action

Page 85 of the Lexmark Printer user manual — Dead Machine
Page 85 · click to enlarge
Page 85

4085-001

3 Paper Feed Pick Motor

With the power on, check for the following readings: (J3) pin 3 to ground = 5 V dc (J3) pin 6 to ground = 35 V dc (J3) pin 7 to ground = 35 V dc (J3) pin 10 to ground = 5 V dc

If voltage is incorrect, replace tray 2 card. If voltage is correct, disconnect (J3). Check between 6 and 7 on the connector for approximately 11.8 ohms. If reading is incorrect, replace the paper feed pick motor assembly. If reading is correct, check the continuity between each 6 and 7 to the motor case. If continuity exists, replace the paper feed pick motor assembly.

With the power on, check the voltage at (J1) paper feed motor connector. The voltage at each pin should read approximately 34 V dc. If voltage is correct check continuity. If continuity is incorrect, replace the paper feed motor. If symptom remains, go to step 4.

4 Tray 2 Sensor Check

See “Tray 2 Sensor Test” on page 3-27 . If test fails, replace the sensor.

5 RIP Card Cable Check the continuity of the RIP card cable. If incorrect, replace the cable. If correct, replace the RIP card.

Power Supply Service Check

Dead Machine

1 AC Outlet Check the AC outlet for correct line voltage. If incorrect, inform the customer.

Show 4 more labels / short text on this page
FRU Action · Paper Feed Motor · FRU Action · Diagnostic Information 2-63
Page 86 of the Lexmark Printer user manual — RIP Card Service Check
Page 86 · click to enlarge
Page 86

4085-001

2 Power Line Cord Check the power line cord for damage. Check the continuity of the line cord and replace if necessary.

3 Power Switch Check the continuity on the power switch. If incorrect, replace the power switch.

4 Power Supply With the power switch turned on, verify the voltage readings at RIP card connector (J1) and engine board connector (J1). The RIP card voltage at J1-1 and J1-2 should be approximately +5 V dc at each pin. Check the engine board connector (J1) voltage to verify that J1-3 and J1-4 have approximately +35 V and J1-11, J2-12 read 5 volts each.

RIP Card Service Check

1 Parallel or USB does not work

Check parallel or USB cables and J2 connection. If OK, check the voltage reading at connector J1 for +5 V dc at pins 1 and 2. If the voltage reading is correct, replace the RIP card. If voltage is not correct, replace the power supply.

FRU Action · FRU Action

Page 87 of the Lexmark Printer user manual — 4085-001
Page 87 · click to enlarge
Page 87

4085-001

Print Quality Service Check

The machine print quality can look poor as a result of either faulty printheads or poor carrier to printhead electrical contact. Generally random missing nozzles indicate a printhead failure. However, more patterned print quality defects may be caused by poor carrier to printhead electrical contact or electrical interface problems with the carrier cable, carrier card, or engine card. Print the ‘Contacts Page’ in diagnostics to evaluate for electrical interface errors.

1 Printhead Carrier Assembly

Print the 'Contacts Page' in diagnostics. Look for breaks in the diagonal lines that are printed on the page. If the missing nozzles are patterned, the problem could be pogo pin to printhead tab circuit contact. Remove the printhead and clean the tab circuit with a clean, lint-free, damp cloth. Inspect the carrier for bent pogo pins, or for contamination on the pogo pins. Clean the pogo pins only with a clean, lint-free cloth. (care should be taken to avoid contact with the pogo pins that contact the ink tank memory chips. These pins are lubricated with a grease to minimize wear and prevent pogo pin damage. This grease should not be smeared on the surrounding pogo pins as it may trap contamination and cause contact failures).

2 Printheads If the error is random missing nozzles, conduct a clean as described on page 3-8. Try cleaning the printhead nozzle plate by holding a damp cloth against the nozzle plate for about three seconds. Gently blot and wipe dry. Replace if necessary.

3 Carrier Cable If the missing nozzles are patterned, the problem could be the carrier cable. Inspect for damage and replace if necessary. Check that the carrier cable connections are clean and secure.

FRU Action · Diagnostic Information 2-65

Page 88 of the Lexmark Printer user manual — 4085-001
Page 88 · click to enlarge
Page 88

4085-001

If the missing nozzles are patterned, the problem could be the engine board or carrier card. First try replacing the engine board, then the carrier card.

5 Paper Feed Ink smudging and smearing can be caused by paper problems or problems in the paper feed area.

Check the following:

  • Correct type of paper is being used.
  • Paper for curl or wrinkles.
  • Feed rollers for wear, dirt, or looseness.
  • Gears for wear or binds.
  • Paper path for obstructions.
  • Distance between print media and printheads.

6 Transport Blurred print and voids can be caused by problems in the transport area. Check the following:

  • Transport belt for wear and full engagement into the carrier grip.
  • Carrier guide rod for wear or dirt.
  • Carrier to carrier frame engagement should be lubricated with grease P/N 99A0394. Lubricate the carrier guide rod and carrier frame on both sides where the two surfaces ride on the frame.
  • Idler pulley parts for wear, damage, or looseness.
  • Encoder strip for wear or dirt.

7 Alignment Characters having uneven or jagged edges, or uneven vertical, horizontal, bidirectional (black or color) alignment can be checked by entering Diagnostics Mode and selecting Align Printheads. See “Aligning the Printheads” on page 3-5 .

8 Ink Cartridges Check the ink cartridges.

FRU Action · 4 Engine Board · Carrier Card

Page 91 of the Lexmark Printer user manual — User Error Messages
Page 91 · click to enlarge
Page 91

4085-001

Cam System Motor/Sensor Service Check

1 Motor does not work. Bat Wings do not move.

Check the voltage at connector (J8) on the engine board. At pins 1, 2, 3, and 4 with the power on. There should be approximately +34 V dc on each pin to ground. If the voltage is incorrect, replace the engine board. If the voltage is correct, disconnect (J8) and check between pins 2 and 4 on the connector for approximately 7.5 ohms. If the reading is incorrect, check the continuity between pins 2 and 4 to the motor case. If continuity exists, replace the cam system motor.

To check the sensor, check connector (J8) at pin 5 for approximately +4.9 volts. If voltage is incorrect, replace the engine board. If the voltage is correct, disconnect (J8) from the engine board and check for an ohm reading of 6.95 between pins 5 and 7. If the reading is not correct, replace the sensor.

User Error Messages

30 Cartridges Missing:

Press Go to clear the error. Supplies status appears on the display and the cartridge missing shows in the supplies menus. This remains until the user accesses the Tests Menu to install a cartridge and fill the empty slots.

  • Color
  • Black

FRU Action · Message Explanation · Diagnostic Information 2-69

Page 92 of the Lexmark Printer user manual — 4085-001
Page 92 · click to enlarge
Page 92

4085-001

38 Memory Full Press Go to clear the message and continue processing the job. Some data will be lost. You must allow additional memory to complete your print job by:

  • Deleting fonts, macros, and other data in RAM.
  • Simplifying your print job.
  • Installing additional memory. Press Menu> or Menu< to access the reset function in the Busy/Waiting Menu group.

Menu Lockout does not prevent access to the Busy/Waiting Menu group. The menu buttons are not active when Reset Control is Off.

51 Defective Flash Press Go to clear the message and continue processing the job. All downloaded fonts and macros not written to flash will be deleted.

Press Menu> or Menu< to access the reset function in the Busy/Waiting Menu group.

Menu Lockout does not prevent access to the Busy/Waiting Menu group. The menu buttons are not active when Reset Control is Off.

53 Unformatted Flash Press Go to clear the message. The flash is marked as bad and normal operation continues. Flash operations will not be allowed until the flash is formatted.

Message Explanation

Page 93 of the Lexmark Printer user manual — 4085-001
Page 93 · click to enlarge
Page 93

4085-001

54 Parallel Error An IEEE 1284 protocol error is detected on the parallel host interface, or due to a faulty cable.

Once a host interface error has been displayed for the first time, reporting of further host interface errors for the associated port is suppressed until the interface parameters are changed, or the printer is powered off.

Press Go to clear the message and continue processing the print job. The job may not print correctly. Verify that the correct cable is used. If a serial error has occurred, be sure the serial interface parameters (protocol, baud, parity and data bits) are set correctly on the printer and the host computer. If a parallel error has occurred, check the cable connection between the host and printer.

Press Menu> or Menu< to access the reset function in the Busy/Waiting Menu group.

Menu Lockout does not prevent access to the Busy/Waiting Menu group. The menu buttons are not active when Reset Control is Off.

Press and hold Select and then press Return to determine the exact cause of host interface error.

If a serial error has occurred, a 16-bit error code displays in hexadecimal on the second line of the LCD. If bit 15 is on, a framing error has occurred. If bit 14 is on, an overrun error has occurred. If bit 13 is on, a parity error has occurred.

Message Explanation · Diagnostic Information 2-71

Page 94 of the Lexmark Printer user manual — 4085-001
Page 94 · click to enlarge
Page 94

4085-001

56 Parallel Port Disabled Once the error has been displayed for the first time, reporting of further errors is suppressed until the menus are entered, or the printer is reset.

Press Go to clear the message. The printer discards any data received on the serial port. Enable the serial port.

Press Menu> or Menu< to access the reset function in the Busy/Waiting Menu group.

200 Paper Jam This message indicates that a paper jam has occurred. If the error does not clear after cleaning the paper jam, see the “Paper Feed Service Check” on page 2-60 .

Message Explanation

Page 95 of the Lexmark Printer user manual — 4085-001
Page 95 · click to enlarge
Page 95

4085-001

3. Diagnostic Aids

Printer Operations

Operations Initiated by Pressing Buttons at Power-On Reset

The table below contains a list of the printer operations that are activated by pressing a sequence of buttons while powering on the printer.

Power-On Reset Button Functions

Function POR Key Sequence Reference Section

See “Disable/Enable Operator Panel Menus” on page 3-2.

Enter CE Diagnostics Mode (Mode 1)

Go and Return See “Entering CE Diagnostics Mode” on page 3-2.

Enter CE Diagnostics Mode (Mode 2)

Go and Select See “Entering CE Diagnostics Mode” on page 3-2.

Clear NVRAM Menu> and Select and Go See “Clear NVRAM (non- critical sections only)” on page 3-3.

Enter Flash Engine Mode

Menu> and Select and Return

See “Enter Flash Engine Code Mode” on page 3-3.

Show 5 more labels / short text on this page
Enter Configuration Menu · Select and Return · Disable/Enable Panel Menus · Go and Stop · Diagnostic Aids 3-1
Page 96 of the Lexmark Printer user manual — Entering CE Diagnostics Mode
Page 96 · click to enlarge
Page 96

4085-001

Disable/Enable Operator Panel Menus

To prevent users from accessing the Ready Menu group and modifying default printer settings, follow these steps:

1. Turn off the printer. 2. Press and hold the buttons identified in the “Power-On Reset Button Functions” on page 3-1 to gain access to the Configuration Menu Group. 3. Turn on the printer. Release the buttons once the Performing Self Test message is displayed. The printer performs its normal POR cycle and shows the first entry in the Configuration Menu. 4. Select the Panel Menu setting and modify the value to Disable. The Disabling Menus message is temporarily shown. Note: These steps do not prevent access to other menu groups.

To unlock, that is, enable the menus, repeat the above steps except modify the Panel Menus value to Enable. To indicate the menus are being unlocked, the Enabling Menus message is shown.

If a user attempts to access the Ready Menu Group while the menus are locked, the printer instead automatically provides access to the Busy/Waiting Menu group. Access to the Busy/Waiting Menu group permits the user to execute operations available in this menu when the printer is not busy.

Entering CE Diagnostics Mode

Page 97 of the Lexmark Printer user manual — Enter Flash Engine Code Mode
Page 97 · click to enlarge
Page 97

4085-001

Use the following steps to access the Diagnostics printer settings and operations.

1. Turn off the printer. 2. Press and hold the buttons identified in “Power-On Reset Button Functions” on page 3-1 . 3. Turn on the printer. Release the buttons once the Performing Self Test message is displayed.

Clear NVRAM (non-critical sections only)

This operation restores factory default values for most printer settings.

Use the following steps to restore the factory default values for all affected settings:

1. Turn off the printer. 2. Press and hold the buttons identified in “Power-On Reset Button Functions” on page 3-1. 3. Turn on the printer. Release the buttons once the Performing Self Test message is displayed.To indicate factory defaults are being restored, the Restoring Factory Defaults message is displayed. Note: This operation can also be initiated from the Configuration Menu Group by selecting the Factory Defaults = Restore All option. The restoration of the factory default values occurs after the user exits the Configuration Menu Group.

Enter Flash Engine Code Mode

This operation lets you POR the printer into a mode that disables the Engine Code, and lets you program new code in the Engine card. Typically this function is used to reprogram defective Engine code.

Diagnostic Aids 3-3

Page 98 of the Lexmark Printer user manual — Change Printheads
Page 98 · click to enlarge
Page 98

4085-001

Use the following steps to enter Flash Engine Code mode:

1. Turn off the printer. 2. Press and hold the buttons identified by the “Power-On Reset Button Functions” on page 3-1 . 3. Turn on the printer. Release the buttons once the performing self Test message is displayed. 4. Begin programming the Engine code when the Invalid Engine Code message is displayed.

Change Ink Cartridges

When the cover is opened, the carrier moves to the far left. The user can then replace any combination of ink cartridges. (In this position, the printheads cannot be removed -- only the ink cartridges can be replaced.) When the cover is closed, the carrier returns to the print position. The ink level is on the ink cartridges, so the reported ink level (using NPA or the Menus Page) is automatically updated.

Alternatively, there is a menu item in the Utilities Menu which can be selected to replace an ink cartridge. Select Change Ink Cartridge from the Utilities Menu. Open the cover and the carrier moves to the far left and any combination of cartridges can be replaced.

If an unsupported ink cartridges is installed, an Attendance Message is shown. This can occur if the software keys in the printer and ink cartridge are incompatible, as in the case of an OEM printer using Lexmark-branded ink cartridges.

Change Printheads

Select Change Printhead from the Utilities Menu. Open the cover and the carrier moves to the middle and any combination of printheads can be replaced.

If there is a defective or missing printhead when the cover is open, the carrier automatically moves the printhead change location (without the selection of the menu item).

The printhead life count is kept on the printhead itself, so the reported life level (using NPA or the Menus Page) is automatically updated.

Page 99 of the Lexmark Printer user manual — Coarse Alignment
Page 99 · click to enlarge
Page 99

4085-001

If an unsupported printhead is installed, an Attendance Message is shown. This can occur if the software keys in the printer and printhead are incompatible, as in the case of an OEM printer using Lexmark-branded printheads.

Following a printhead replacement, the printer automatically initiates an alignment procedure.

Aligning the Printheads

User Alignment

The printheads come from the factory pre-aligned and do not need to be aligned. However, certain customers may want to align printheads to achieve real or perceived optimal print quality. To align the printheads, select Align Printheads from the Utilities Menu. An alignment page prints. From each section of the alignment page, the user is required to pick a selection that “lines up” the best. Enter each selection on the operator panel.

Coarse Alignment

User Alignment should suffice for aligning the printheads. However, for manufacturing, CE personnel and other cases, Coarse Alignment may be used. The purpose of the Coarse Alignment is to get the printheads roughly aligned - User Alignment is for fine tuning. Select Coarse Alignment from the Configuration Menu. A coarse alignment page prints. From each section of the alignment page, the user is required to pick a selection that “lines up” the best. Enter each selection on the operator panel.

Diagnostic Aids 3-5

Page 100 of the Lexmark Printer user manual — 4085-001
Page 100 · click to enlarge
Page 100

4085-001

Alignment Page Fixed Settings (User Alignment and Coarse Alignment)

Printer Setting Value Used for Menus Page

Paper Source If the User Default Paper Source contains letter, legal, or A4, the alignment page is printed from the User Default Paper Source.

If not, another source is automatically chosen.

Paper Size If the User Default Paper Source contains letter, legal, or A4, the alignment page is printed on the User Default Paper Source’s installed size.

If not, the alignment page is formatted for letter or A4 based on the value of the US/NonUS printer setting.

Paper Type The selected source’s installed paper type.

Separator Sheets None · Orientation Portrait

Page 101 of the Lexmark Printer user manual — 4085-001
Page 101 · click to enlarge
Page 101

4085-001

Cleaning Printheads

The Clean Printheads operation is used to clean and maintain the printheads. This mechanical operation performed by the print engine is recommended when print quality becomes degraded.

There are two classes of cleaning that can be performed:

  • Short Clean is a “spit and wipe” cycle followed by a Print Quality test page. Short Clean should be used first.
  • Long Clean consists of printing a Print Quality test page, prompting the user for “bad” printheads, selective priming of “bad” printheads, printing the Print Quality test page, and then prompting the user to see if print quality has improved. If print quality improves and is acceptable on all printheads, the Ready prompt appears. If print quality has not improved, the process repeats. Long Clean can result in the disposal of a significant amount of ink and as such should be used only when Short Clean does not correct the problem.

Diagnostic Aids 3-7

Page 102 of the Lexmark Printer user manual — Linking Input Trays
Page 102 · click to enlarge
Page 102

4085-001

Print Quality Test Page Fixed Settings

Printer Setting Value Used for Menus Page

Paper Source If the User Default Paper Source contains letter, legal, or A4, the alignment page is printed from the User Default Paper Source.

If not, another source is automatically chosen.

Paper Size If the User Default Paper Source contains letter, legal or A4, the alignment page is printed on the User Default Paper Source’s installed size.

If not, the alignment page is formatted for letter or A4 based on the value of the US/NonUS printer setting.

Paper Type The selected source’s installed paper type.

As the operation is performed, Cleaning Printheads is displayed.

Linking Input Trays

Most network printers offered by Lexmark support an input tray linking feature. In all cases, the feature can be turned on and off by the user. For instance, some previous Lexmark laser printers let the user set tray linking to one of the following values: Off, Tray 1+2, Tray 1+3, Tray 1+2+3. In general, to turn tray linking on, the user had to decide which group of trays should be linked. Furthermore, only one set of trays could be linked. With the tray linking feature turned on, the specified trays would be linked if they contained the same media size.

Separator Sheets None · Orientation Portrait

Page 103 of the Lexmark Printer user manual — 4085-001
Page 103 · click to enlarge
Page 103

4085-001

Input tray linking description:

  • Input sources which contain the same paper size, custom string, and paper type are linked automatically. Tray linking is always active. To prevent sources with the same media from being linked, the user must set the corresponding paper type settings to different values.
  • PerfectFinish capability affects the ability of trays to link. For instance, in the following example, all the trays have the same size, type, and custom string, which for the traditional Lexmark network printer would mean the trays are all linked. However, the MP Feeder does not support PerfectFinish, so it would not automatically be linked with the other trays.

Input Source Media Size Media Type Custom String

Tray 1 Letter Plain Paper Null Yes

Tray 2 Letter Plain Paper Null Yes

MP Feeder Letter Plain Paper Null No

  • Any combination of trays that support the same media size and media type can be linked by setting the paper size, paper type, and custom string alike.
  • Input sources which support paper (Letter, Legal,..., not envelopes) are linked in the following order. The printer only uses this search order when the input source requested by the print job is empty. In general, the input source requested by the print job has priority.

– MP Feeder (if configured as Cassette and if PerfectFinish

has not been requested by the print job) – Tray 1 – Tray 2

PerfectFinish Capability · Diagnostic Aids 3-9

Page 104 of the Lexmark Printer user manual — Printing Menu Settings Page
Page 104 · click to enlarge
Page 104

4085-001

Unsolicited Manual Feed

When configured without a MP Feeder, a user may perform an unsolicited manual feed. Prior to sending a job (or before the first page of the job is picked), a user sticks a piece of paper in the manual slot. The engine “grabs” the paper and pulls it into the nip. The engine waits for the RIP to submit the print page. Regardless of which source the RIP requests for that page, it prints on the page that was inserted. Furthermore, the RIP and engine assumes that the media that was inserted is the requested size and type that were selected through the data stream.

Manual Duplex

Through the driver, this printer supports manual duplex. Select manual duplex from the driver UI and the printer forces all sheets (front and back sides) to be printed from tray 1 (this eases the confusion related to sequencing of sides). After the driver has sent the front sides of the job, a data stream command sent from the driver prompts the user to reinsert the sheets (face up) into tray 1. After pressing Go, the printer continues and prints the back sides from tray 1.

Printing Menu Settings Page

Select Print Menus from the Utilities Menu. The printer automatically exits the control panel menus and prints the menus page. The Printing Menu Settings message appears and the Power indicator blinks while the page formats and prints.

  • List of all the printer settings in the control panel menus, and their default values.
  • List of the installed features such as RAM memory SIMMs, optional input trays, flash, and disk.
  • Printer information such as serial number, page count, installed RAM, Engine code level, RIP code level, tray code levels,
Page 105 of the Lexmark Printer user manual — Menus Page Fixed Settings
Page 105 · click to enlarge
Page 105

4085-001

  • Control Panel code level, Font ROM Version, and SRAM availability.
  • The RIP code level is appended with “:F” or “:R” to indicate whether the board is running code from flash (re programmable) or ROM (not re programmable). This may be useful for product engineers or Customer Support.
  • Miscellaneous supplies information that can be used by the Customer Support Center. Note: The menus page is printed in the language specified by the Display Language printer setting, unless the Display Language printer setting is Japanese, in which case the menus page is printed in English.

Menus Page Fixed Settings

Printer Setting Value Used for Menus Page

Paper Source If the User Default Paper Source contains letter, legal, or A4, the menus page is printed from the User Default Paper Source.

If not, another source is automatically chosen.

Paper Size If the User Default Paper Source contains letter, legal, or A4, the menus page is printed on the User Default Paper Source’s installed size.

If not, the menus page is formatted for letter or A4 based on the value of the US/NonUS printer setting.

Paper Type The selected source’s installed paper type.

Separator Sheets None · Orientation Portrait · Diagnostic Aids 3-11

Page 106 of the Lexmark Printer user manual — Canceling a Print Job using the Operator Panel
Page 106 · click to enlarge
Page 106

4085-001

TSC fields on the Print Menus Page

The following fields are on the Print Menus page under the “Printer Information” heading. The fields are intended to aide the TSC or a CE in diagnosing problems.

TS1 Concatenation of C,M,Y, and K ink levels.

TS2 Concatenation of C, M, Y, and K PH life remaining.

E1 Concatenation of C, M, Y, and K expiration dates in mmyy format.

R1 Concatenation of C, M, Y, and K tanks (0 indicates non-refilled, 1 indicates refilled.)

Restoring Factory Defaults

The Factory Defaults operation returns most of the operator panel settings in the Ready Menu Group back to their factory settings.

As the operation is performed, the Restoring Factory Defaults message is shown.

The following settings in the Ready Menu Group do NOT reset to factory default values:

  • Display Language (SETUP MENU),
  • All settings in the PARALLEL MENU, SERIAL MENU, NETWORK MENU, INFRARED MENU, LOCALTALK MENU, USB MENU and FAX MENU.

Canceling a Print Job using the Operator Panel

The Cancel Job control panel function is used to cancel printing of the current job. Since the printer is capable of storing many pages associated with one or more print jobs from any installed host interface at the time this operation is selected, users need to understand the printer’s algorithm for determining which print job is canceled.

Field Definition

Page 107 of the Lexmark Printer user manual — 4085-001
Page 107 · click to enlarge
Page 107

4085-001

When each sheet is printed and the engine has placed the sheet in a printer bin, the print engine sends a “Print Complete” signal to the printer controller to indicate the associated sheet is complete. However, since most printer bins are not equipped with sensors to detect when a sheet has arrived in a bin, many printers use an existing sensor in the printer’s paper path located closest to the selected bin as a trigger for this signal. For example, many laser printer engines send the “Print Complete” signal when the trailing edge of a sheet crosses the sensor located in the area of the fuser.

When the Cancel Job operation is selected, the printer identifies the next sheet for which “Print Complete” will be received and cancels the print job associated with the identified sheet.

The cancel job operation is in the control panel JOB MENU. This menu can be accessed while the printer is in the ready (or idle state), the waiting state, the busy state, and while many intervention conditions as well as status conditions are displayed.

When a job is canceled:

  • After the printer identifies which job is canceled, the printer determines whether the canceled job has ended or has been terminated.
  • If the canceled job has ended or has been terminated, all sheets belonging to the canceled job for which the physical printing process has not yet begun are canceled, and the printer immediately begins processing the next print job.
  • If the canceled job has neither ended nor been terminated: – A user may stop the canceled job by executing a Front Panel

Reset operation. After reset processing is complete, the printer begins processing the next print job. – If the host computer continues to send data which belongs to

the canceled job, the printer discards the data until the job ends or is stopped. Once the cancellation processing is complete, the printer begins processing the next print job.

Diagnostic Aids 3-13

Page 108 of the Lexmark Printer user manual — Resetting the Printer using the Operator Panel
Page 108 · click to enlarge
Page 108

4085-001

– If the host computer stops sending data without ending the

canceled job, the printer initiates a timer which stops the canceled job. (For PCL emulation, the printer uses the Flushing timer value.) Note: If the host computer resumes sending data which belongs to a canceled job, then the timer value used to stop the job is reset and the printer resumes looking for a data stream command which indicates the job has ended. However, if the host computer stops sending data again, the procedure to stop the job is repeated, meaning the appropriate timer is restarted from the beginning. When the expiration of the applicable timer occurs, the canceled job is stopped and the printer begins processing the next print job.

Note: If a user has disabled the Print timeout timer which is used to terminate a PPDS job, and the cancel operation is used on a PPDS job which does not contain an end of job command, the printer’s ability to complete the cancellation operation is suppressed. In other words, the printer is deadlocked waiting for an end of job command which will never be sent. When this situation occurs, the user must explicitly execute a Front Panel Reset to terminate the canceled PPDS job. (This is not an issue for PCL emulation since the Flushing timer is used to terminate a canceled PCL job.)

Invoking Cancel Job

1. While the printer is in a state which permits the cancel job operation, press Menu> or Menu< . The following screen is displayed.

JOB MENU

2. Press Select . The printer automatically exits the control panel menus and performs the job cancel operation. As the job is canceled, the Canceling Job message appears.

Resetting the Printer using the Operator Panel

The Reset Printer control panel function is used to reset the active port and restore the printer’s user default settings.

Cancel Job

Page 109 of the Lexmark Printer user manual — 4085-001
Page 109 · click to enlarge
Page 109

4085-001

The reset printer function is in the operator panel JOB MENU. This menu is available in both the Ready Menu Group and the Busy/ Waiting Menu Group.

When the printer is reset from the operator panel, the printer is initialized as follows:

  • A maximum of one page is launched; all other queued pages are discarded.
  • If an interpreter is currently processing data for a page, the data and partially completed page are discarded.
  • Fixed default settings are reset to the factory set values.
  • PJL current environment is restored to the user default environment.
  • Variable default settings for paper sizes become the active default formatting sizes.
  • Data on only the active port is discarded in the following manner:

– Parallel - the host computer stops sending data and link data

is discarded until data has not been received for a half of a second. – USB - the host computer stops sending data and link data is

discarded until data has not been received for a half of a second.

Diagnostic Aids 3-15

Page 110 of the Lexmark Printer user manual — JOB MENU
Page 110 · click to enlarge
Page 110

4085-001

Invoking Reset Printer (from the Ready message)

1. Press Menu> or Menu< to enter the menus. The following screen is displayed.

SUPPLIES MENU

2. Press Menu> or Menu< until JOB MENU is displayed on the second line. Press Select . The following screen is displayed.

JOB MENU

3. Press Select . The printer automatically exits the operator panel menus and performs the reset operation. As the operation is performed, the Resetting the Printer message appears.

Invoking Reset Printer (from Hex Trace mode, and all other messages)

1. Press Menu> or Menu< to enter the menus. Since the JOB MENU is the only menu active, the printer automatically selects it and displays the following screen.

JOB MENU

2. Press Select . The printer automatically exits the operator panel menus and performs the reset operation. As the operation is performed, the Resetting the Printer message appears. Note: The system administrator can disable the Reset Printer function by turning the Reset Control setting off. Reset Printer is not displayed when Reset Control is set to off.

Reset Printer · Reset Printer

Page 111 of the Lexmark Printer user manual — INIT * -- Parallel Interface Initialization
Page 111 · click to enlarge
Page 111

4085-001

Other Resets

Power On Reset -- and similar resets

When the printer is turned on, the following events occur:

  • Fixed default settings are set to factory set values.
  • Portions of printer memory that store page, font, and macro information are cleared.

Other resets which cause similar events:

  • NPA Cold Start (Front Panel, 01 or 03).
  • INA Hard Reset

For these resets, currently active pages are discarded and emulators are reset.

INIT * -- Parallel Interface Initialization

The INIT * signal causes the printer to be initialized as follows (unless the INIT * signal is disabled by its variable default setting):

  • Data received before reception of an INIT * signal is printed, and then initialization takes place.
  • Variable default settings are returned to values stored in NVRAM.
  • Fixed default settings are reset to factory set values.
  • Downloaded fonts and macros with permanent status are retained.
  • Downloaded fonts and macros with temporary status are deleted.
  • Variable default settings for paper sizes become the active default formatting sizes.
  • The link buffer is left intact.

INIT * is not honored while Hex Trace is active. Receiving INIT * causes the parallel interface to go busy. The INIT * is processed when the parallel interface becomes active and all preceding characters have been processed.

Diagnostic Aids 3-17

Page 112 of the Lexmark Printer user manual — JOB MENU
Page 112 · click to enlarge
Page 112

4085-001

NPA Response

Any reset conditions that cause the loss of resources or a change in emulation requires an NPA response to inform the host computer. See separate specifications on NPA implementation. NPA responses are only given if NPA bidirectional communication is active in the printer.

Loss of Link Data and Link Response

An operator panel reset is the only reset condition which causes the loss of link data.

For all other reset cases, the link remains active and takes data until the link buffer fills.

When an intervention required error condition occurs, the error is fed back immediately to the attached host computer. The link immediately goes busy on intervention required conditions.

Printing Buffer Contents

The print buffer operation is used to print any partial page that is waiting to be printed. This situation occurs when a PCL 5 emulation or PPDS job is sent to the printer, but it doesn’t contain a Form Feed command after the last page. When this situation occurs, the Waiting message is displayed.

To invoke the Print Buffer operation while the Waiting status screen is displayed, follow these steps.

1. Press Menu> or Menu< to enter the menus. The following screen is displayed.

JOB MENU

2. Press Menu> until the following screen is displayed.

JOB MENU

Reset Printer · Print Buffer

Page 113 of the Lexmark Printer user manual — Registration
Page 113 · click to enlarge
Page 113

4085-001

3. Press Select . The printer automatically exits the operator panel menus and prints the partial page. Note: If the Print Buffer operation is selected while the printer is not in the Waiting state, the printer automatically exits the operator panel menus, but no page is printed.

Activating Hex Trace Debug Mode

The Hex Trace menu function puts the printer in a mode that is used to isolate print job problems. Each byte of information contained in the job is printed in both hexadecimal and character formats. Therefore, all emulation commands (PCL 5, PS 2, PJL, and so on) are printed rather than processed, as is normally done.

To activate hex trace mode, select Hex Trace from the UTILITIES MENU.

To exit hex trace mode, select Reset Printer from the JOB MENU or turn the printer off.

Diagnostics (Mode 1) - Print Tests

Registration

Upon selection, this item will first cause a page to be printed from the requested source, then proceed to a menu screen where the registration can be entered. While the page is printing, the Power indicator should blink and the following screen will be displayed:

The printer prints the registration page from the requested source. It is assumed that either Letter or A4 is loaded into the requested source.

No buttons are active while the registration page is printing. Once complete, the registration screen is displayed.

Registration Page · Printing · Diagnostic Aids 3-19

Page 114 of the Lexmark Printer user manual — Input Source Print Tests
Page 114 · click to enlarge
Page 114

4085-001

The Registration menu is formatted so that all menu items fit on a single screen as shown. This allows manufacturing to quickly set and verify the registration setting.

T= sxx* L= sxx*

Terminology:

  • T represents Top Margin and L represents Left Margin.
  • s represents the sign for negative values. This space is blank for positive values.
  • xx represents the margin value.
  • An asterisk (*) is displayed next to the default value.

Upon first entering the Registration menu, the Left margin sign/value pair flashes. This indicates it is the margin value being changed. To change the value, press either Menu> or Menu<. Once the value you want is displayed, press Select to save the value and move to the next margin value. The margin values are traversed in this order: Top, then Left. If you need to skip a margin value (that is its value is OK), press Select. The default value remains the same.

If Return is pressed to exit the Registration menu after a margin value has been incremented or decremented (but not saved via Select), then the default value is not changed.

To exit the Registration menu, press Return.

Input Source Print Tests

The Diagnostic Input Source PRINT TESTS verifies that the printer can print on media from each of the installed input sources. Each of the installed sources is available as a selectable option within the PRINT TESTS menu. For each source, there are two choices:

  • Single (print the Print Test page once).
  • Continuous (continue printing the Print Test page until Return or Stop is pressed).

Tray 1

Page 115 of the Lexmark Printer user manual — 4085-001
Page 115 · click to enlarge
Page 115

4085-001

The content of the Print Test page varies depending on the media installed in the selected input source. If a source is selected that contains paper (that is, letter, legal, and so on), then a page similar to the Quick Test page is printed. However, it does not contain the Print Registration diamonds. If a source is selected which contains envelopes, then an Envelope Print Test pattern is printed. This pattern only contains text, which consists of continuous prints of each character in the selected symbol set.

If Continuous is selected, all sources printing with paper sizes prints the same page continuously until the test is stopped. If Continuous is selected for a source which contains envelopes, then the envelope print test pattern is printed on the first envelope and subsequent envelopes are blank.

While the page is printing the following message is displayed. The Power indicator also blinks while the page is printing.

If Single is selected, no buttons are active while the Print Test page is printing. However, if Continuous is selected, Return or Stop can be pressed to cancel the test. While the test is being canceled, the following message is displayed.

canceling...

Show 4 more labels / short text on this page
<Input source> · Printing · <Input source> · Diagnostic Aids 3-21
Page 116 of the Lexmark Printer user manual — LCD Hardware Test
Page 116 · click to enlarge
Page 116

4085-001

Contacts Page Print Test

This test prints the Contacts Page, which can be used by the Customer Support Center or CE to diagnose problems involving printheads, printhead cables, pogo pins, or electrical interfaces between the printheads and the carrier.

Contacts Page Fixed Settings

Printer Setting Value Used for Menus Page

Paper Source If the User Default Paper Source contains letter, legal, or A4, the alignment page is printed from the User Default Paper Source.

If not, another source is automatically chosen.

Paper Size If the User Default Paper Source contains letter, legal, or A4, the alignment page is printed on the User Default Paper Source’s installed size.

If not, the alignment page is formatted for letter or A4 based on the value of the US/NonUS printer setting.

Paper Type The selected source’s installed paper type.

Diagnostics (Mode 2) - Hardware Tests

LCD Hardware Test

Select this test to continually execute the LCD display test. To cancel the test, press Return or Stop.

Show 4 more labels / short text on this page
Prt Contacts Pg · Printing · Separator Sheets None · Orientation Portrait
Page 117 of the Lexmark Printer user manual — P:###### F:#####
Page 117 · click to enlarge
Page 117

4085-001

Button Test

The Button Test verifies the operation of each button on the operator panel. When Button Test is selected, the following screen is displayed.

OP

OP OP

While a button is pressed, CL (Closed) is displayed. Likewise, while a button is not pressed, OP (Open) is displayed. If the wrong message is displayed, then the button is malfunctioning.

To exit the button test, press Return or Stop. The previous menu screen will be displayed when the button is released.

DRAM Memory Test

The DRAM Memory Test checks the validity of DRAM (both standard and optional DRAM). The test involves writing patterns of data to DRAM to verify that each bit in memory can be set and read correctly. When this test is selected from the control panel, the following screen is displayed and the printer begins testing DRAM memory for the first time.

P:###### F:#####

Terminology:

  • P:###### represents the number of times the memory test has passed (finished successfully). Initially 000000 is displayed for ######. The maximum pass count is 999,999.
  • F:##### represents the number of times the memory test has failed (finished with errors). Initially 00000 is displayed for #####. The maximum fail count is 99,999.

DRAM Memory Test · Diagnostic Aids 3-23

Page 118 of the Lexmark Printer user manual — P:###### F:#####
Page 118 · click to enlarge
Page 118

4085-001

The power indicator blinks indicating the memory test is in process. The printer continually runs the same test until canceled from the operator panel (by pressing Return or Stop).

Each time the test finishes, the screen is updated with the result. If the test passes, the Pass Count is incremented by 1. However, if the test fails, a failure message is displayed for approximately 3 seconds and the Fail Count is incremented by 1.

  • DRAM Error

Once the maximum pass count or fail count is reached, the test is stopped and the final test results are displayed. Press Return or Stop to exit the test.

ROM Memory Test

The ROM Memory Test checks the validity of the RIP code and fonts. When this test is selected from the operator panel, the following screen is displayed and the printer begins testing ROM memory for the first time.

P:###### F:#####

Terminology:

  • P:###### represents the number of times the memory test has passed (finished successfully). Initially 000000 is displayed for ######. The maximum pass count is 999,999.
  • F:##### represents the number of times the memory test has failed (finished with errors). Initially 00000 is displayed for #####. The maximum fail count is 99,999.

The power indicator blinks indicating the memory test is in process. The printer continually runs the same test until canceled from the operator panel (by pressing Return or Stop).

ROM Memory Test

Page 119 of the Lexmark Printer user manual — P:###### F:#####
Page 119 · click to enlarge
Page 119

4085-001

Each time the test finishes, the screen is updated with the result. If the test passes, the Pass Count is incremented by 1. However, if the test fails, one of the following failure messages is displayed for approximately 3 seconds and the Fail Count is incremented by 1:

  • ROM Checksum Error
  • ROM Burst Read Error

Once the maximum pass count or fail count is reached, the test is stopped and the final test results are displayed. Press Return or Stop to exit the test.

Parallel Wrap Test

The Parallel Wrap Test checks the operation of the parallel port hardware using a wrap plug. Each parallel signal is tested.

To perform the wrap test:

1. Disconnect the parallel interface cable, and install the parallel wrap plug (1319128). 2. Select HARDWARE TESTS from the Diagnostics Menu. 3. Select Parallel Wrap to initiate the Parallel Wrap Test. 4. Select the appropriate Parallel Wrap Test (Parallel Wrap, Parallel 1 Wrap, Parallel 2 Wrap, or Parallel 3 Wrap).

The following screen is displayed and the printer begins testing the parallel hardware for the first time.

P:###### F:#####

Terminology:

  • P:###### represents the number of times the test has passed (finished successfully). Initially 000000 is displayed for ######. The maximum pass count is 999,999.
  • F:##### represents the number of times the test has failed (finished with errors). Initially 00000 is displayed for #####. The maximum fail count is 99,999.

Parallel Wrap · Diagnostic Aids 3-25

Page 120 of the Lexmark Printer user manual — 4085-001
Page 120 · click to enlarge
Page 120

4085-001

The power indicator blinks indicating the test is in process. The printer continually runs the same test until canceled from the operator panel (by pressing Return or Stop).

Each time the test finishes, the screen is updated with the result. If the test passes, the Pass Count is incremented by 1. However, if the test fails, one of the following failure messages is displayed for approximately 3 seconds and the Fail Count is incremented by 1.

  • Sync Busy Error
  • Byte Interrupt Request Error
  • Strobe Interrupt Request Error
  • Init Fall Error
  • Init Busy Error
  • Init Rise Error
  • Host Busy Error
  • RAM Data FF Error
  • RAM Data AA Error
  • RAM Data 00 Error
  • RAM Data 55 Error
  • DMA Count Error
  • DMA Address Error
  • DMA Interrupt Error
  • DMA Memory Error
  • DMA Background Error
  • Clear Init Rise Error
  • False Init Rise Error
  • False Init Fall Error
  • Autofeed Rising Interrupt Error
  • Clear Autofeed Rise Error
  • False Autofeed Rise Error
  • Autofeed Falling Interrupt Error
  • Clear Autofeed Fall Error

Once the maximum pass count or fail count is reached, the test is stopped and the final test results are displayed. Press Return or Stop to exit the test.

Page 121 of the Lexmark Printer user manual — PO=OP PT=CL
Page 121 · click to enlarge
Page 121

4085-001

Diagnostics (Mode 2) - Input Tray Tests

Tray 1 Sensor Test

This test determines whether or not the Tray 1 input sensor is working correctly. To run the test, select Tray 1 from the INPUT TRAY TESTS menu. The following screen is displayed:

PO=OP

Terminology:

  • PO or Paper Out refers to the empty sensor.

Once this screen is displayed, the sensor can be manually actuated. When the sensor is closed, CL is displayed. When the sensor is open, OP is displayed. If the wrong message is displayed, the sensor is malfunctioning.

OP = Empty Tray CL = Not Empty

To exit the test, select Return or Stop.

Tray 2 Sensor Test

This test determines whether or not the Tray 2 input sensor is working correctly. To run the test, select Tray 2 from the INPUT TRAY TESTS menu. The following screen will be displayed:

PO=OP PT=CL

Terminology:

  • PO or Paper Out refers to the empty sensor.
  • PT or Pass-through refers to the pass-through sensor.

Once this screen is displayed, the sensors can be manually actuated. When the sensor is closed, CL is displayed. When the

Tray 1 · Tray 2 · Diagnostic Aids 3-27

Page 122 of the Lexmark Printer user manual — PO=OP
Page 122 · click to enlarge
Page 122

4085-001

sensor is open, OP is displayed. If the wrong message is displayed, the sensor is malfunctioning.

PO=OP = Empty PO=CL = Not Empty

PT=OP = Media Clear PT=CL = Media Present

To exit the test, select Return or Stop.

MP Feeder Sensor Test

This test determines whether or not the MP Feeder input sensor is working correctly. To run the test, select MP Feeder from the INPUT TRAY TESTS menu. The following screen is displayed:

PO=OP

Terminology:

  • PO or Paper Out refers to the empty sensor.

Once this screen is displayed, the sensor can be manually actuated. When the sensor is closed, CL is displayed. When the sensor is open, OP is displayed. If the wrong message is displayed, the sensor is malfunctioning.

OP = Empty CL = Not Empty

To exit the test, select Return or Stop.

MP Feeder

Page 123 of the Lexmark Printer user manual — TP=O TF=C
Page 123 · click to enlarge
Page 123

4085-001

Diagnostics (Mode 2) - Base Sensor Tests

Paper Path Sensors

This test determines if a group of sensors related to the paper path are working correctly. To run the test, select Paper Path Sensors from the BASE SENSOR TESTS menu. The following screen is displayed:

TC=C IS=C CO=C

Terminology:

  • TC refers to the PerfectFinish path pass-through sensor.
  • IS or Input Sensor refers to the input (grit roll) sensor.
  • CO or Cover Open refers to the cover open sensor.

Once this screen is displayed, the sensor can be manually actuated. When the sensor is closed, C is displayed. When the sensor is open, O is displayed. If the wrong message is displayed, the sensor is malfunctioning.

TC or IS=O = Media Clear TC or IS=C = Media Present

CO=O = Cover Open CO=C = Cover Closed

To exit the test, select Return or Stop.

Supplies Sensors

This test is used to determine if a group of sensors related to the supplies are working correctly. To run the test, select Supplies Sensors from the BASE SENSOR TESTS menu. The following screen will be displayed:

TP=O TF=C

Paper Path · Supplies Sensors · Diagnostic Aids 3-29

Page 124 of the Lexmark Printer user manual — CS=O
Page 124 · click to enlarge
Page 124

4085-001

Terminology:

  • TP refers to the PerfectFinish tank presence sensor.
  • TF refers to the PerfectFinish fluid level sensor state.

Once this screen is displayed, the sensor can be manually actuated. When the sensor is closed, C is displayed. When the sensor is open, O is displayed. If the wrong message is displayed, the sensor is malfunctioning.

TP=O = Tank Missing TP=C = Tank Present

TF=O = Cartridge Full TF=C = Not Full

To exit the test, select Return or Stop.

Miscellaneous Sensors

This test is used to determine if a group of miscellaneous sensors is working correctly. To run the test, select Misc Sensors from the BASE SENSOR TESTS menu. The following screen is displayed:

CS=O

Terminology:

  • CS refers to the cam stepper home sensor state.

Once this screen is displayed, the sensor can be manually actuated. When the sensor is closed, C is displayed. When the sensor is open, O is displayed. If the wrong message is displayed, the sensor is malfunctioning.

To exit the test, select Return or Stop.

Motors Sensors

Page 125 of the Lexmark Printer user manual — Cap Printheads
Page 125 · click to enlarge
Page 125

4085-001

Ink Level Sensor Test

This test determines if the ink level sensor is working correctly. To run the test, select Ink Level Sensor Test from the BASE SENSOR TESTS menu. The following screen is displayed:

Ink Level Sensor Test

Level = - 602

First the printheads are uncapped. The printheads move to the middle of the frame so that the servicer has unobstructed access to the ink-level sensor. Once the printheads have been presented, the analog ink-level sensor value begins updating in real time. The servicer can affect this value by waving a magnet in front of the sensor.

When the test is ended using the operator panel (Return or Stop), the carrier is homed and the printheads are capped.

Diagnostics (Mode 2) - Subsystem Tests

Uncap Printheads

Selection of this operation initiates a printhead uncapping. After selecting this, the following screen is displayed for 1 second:

After uncapping, this test will automatically exit.

Cap Printheads

Selection of this operation initiates a printhead capping. After selecting this, the following screen is displayed for 1 second:

Printheads Uncapped · Printheads Capped · Diagnostic Aids 3-31

Page 126 of the Lexmark Printer user manual — Carrier System Test
Page 126 · click to enlarge
Page 126

4085-001

After capping, this test automatically exits.

Carrier System Test

This test determines if the carrier system sensor is working correctly. To run the test, select Carrier System Test from the SUBSYSTEM TESTS menu. The following screen is displayed:

Once the test is initiated, the printhheads are uncapped and the carrier attempts an “open-loop” safe move to the middle of the printer without use of any feedback signals from the encoder strip. The goal is to first isolate a problem with the motor or drive. If there is no motion, then the problem is with the DC motor or motor driver, and not the encoder / feedback system. If there is no problem with the motor drive, then the carrier is somewhere out in the middle. If there is a problem, then the servicer can still drag the carrier out to the middle, since the printheads are uncapped. After the engine has finished the open-loop move attempt, no further attempts are made to drive the carrier using the motor and the carrier position begins updating real time on the panel. The servicer can now move the carrier back and forth over the entire carrier shaft. The servicer should move the carrier back and forth at a constant speed to determine if there are any noticeable skips or lags in positional count. A skip or lag in the far left or right regions could indicate a cable connection problem or strip contamination. Typical symptoms include shifting margins on previously printed pages. The encoder strip should be inspected with a light for signs of excessive mist, shaft grease, and fingerprints. It is preferable to replace the strip if it is contaminated. However, the strip can be wiped carefully with a deionized, water moistened lint-free cloth if a replacement strip is unavailable. A check should be made to ensure that the strip is clean and is not loose when installed or re-installed. The operator panel displays real time information that corresponds to the relative position of the carrier as it is moved back and forth. At the completion of testing, the servicer should manually move the carrier back to the right frame before exiting the test by selecting Return or Stop. This moves the maintenance station to the cap position to cap the printheads.

Carrier System Test · Position = 1050

Page 127 of the Lexmark Printer user manual — Maintenance Sled Test
Page 127 · click to enlarge
Page 127

4085-001

Index System Test

This test determines if the index system sensor is working correctly. To run the test, select Index System Test from the SUBSYSTEM TESTS menu. The following screen is displayed:

The index system is run open loop and the real time position count is displayed on the panel.

To exit the test, select Return or Stop.

Maintenance Sled Test

This test determines if the maintenance sled sensor system is properly functioning. To run the test, select Maint Sled Test from the SUBSYSTEMS TESTS menu. The printheads are uncapped. This utilizes the maintenance sled motor. The printheads move to the middle of the frame to give the servicer access to the maintenance homing sensor. The status of the homing sensor now begins updating real time on the panel. The servicer can toggle this status by blocking or unblocking the optical sensor. The following screen is displayed:

The state of the maintenance sled sensor is indicated by “O” for open or “C” for closed.

To exit the test, select Return or Stop. When the test is ended, the carrier is homed and the printheads are capped.

Show 5 more labels / short text on this page
Index System Test · Position = 823 · Maint Sled Test · State = O · Diagnostic Aids 3-33
Page 128 of the Lexmark Printer user manual — K=+ CMY=+
Page 128 · click to enlarge
Page 128

4085-001

Diagnostics (Mode 2) - Supplies Tests

For each of the following four tests, the sequence of events is the same:

1. The printheads are uncapped when the test is invoked. 2. The printheads moves to the middle of the frame to give the servicer access to the printheads and tanks under test. The data corresponding to the test being run begins updating real time on the panel as described. 3. When the test is ended by pressing Return or Stop , the carrier is homed and the printheads are capped.

Ink Tank Memories

This test determines the status of the electrical connection to the ink tank memories. The status is indicated real time by either “+” (good) or “-” (bad). The following screen is displayed:

Ink Tank Mem Test

K=+ C=+ M=+ Y=+

To exit the test, select Return or Stop.

Printhead Memories

This test determines the status of the electrical connection to the printhead memories. The status is indicated real time by either “+” (good) or “-” (bad). The following screen is displayed:

K=+ CMY=+

To exit the test, select Return or Stop.

Printhead Mem Test

Page 129 of the Lexmark Printer user manual — Setting the Page Count
Page 129 · click to enlarge
Page 129

4085-001

K&C TSR Test

This test determines the status of the printhead TSR (thermal sense resistor). The resistance is displayed real time. The following screen is displayed:

K & C TSR Test

K=104B3 C=104A1

To exit the test, select Return or Stop. Note: If zero is displayed on “K”= or “C”=, replace the printhead.

M&Y TSR Test

This to determines the status of the printhead TSR (thermal sense resistor). The resistance is displayed real time. The following screen is displayed:

M & Y TSR Test

K=104B3 C=104A1

To exit the test, select Return or Stop. Note: If zero is displayed on “K”= or “C”=, replace the printhead.

Diagnostics (Mode 2) - Printer Setup

Setting the Page Count

The printer’s page count can be changed using the Diagnostics menus. This menu is used by the CE to reset the Page Count setting whenever the engine card is replaced. The engine card contains the printer’s NVRAM memory. When Page Count is selected from the PRINTER SETUP menu, the current page count is displayed as follows:

Page Count · =1234567* · Diagnostic Aids 3-35

Page 130 of the Lexmark Printer user manual — Viewing and Resetting the Maintenance Page Count
Page 130 · click to enlarge
Page 130

4085-001

The left-most digit (‘1’ in this example) blinks, indicating it is the first digit to be changed. To change the value, press either Menu> or Menu< until the value you want is displayed. Press Select to move to the next digit. The next digit (‘2’ in this example) blinks. Continue modifying each digit using this method. To skip a digit (that is, and keep its current value), press Select.

When Select is pressed after the final digit (‘7’ in this example), the new page count is stored in NVRAM.

Viewing the Permanent Page Count

The permanent page count setting cannot be modified using the operator panel. It can only be viewed using the Diagnostics menus. When Permanent Page Count is selected, the following screen is displayed.

Viewing and Resetting the Maintenance Page Count

The maintenance page counter is incremented when a page is printed and incremented by two when a duplex sheet is printed. The counter is used to track printer usage. When the counter reaches 250,000, a maintenance intervention and a status indicator appears on the panel. The maintenance page count cannot be specifically set using the operator panel. However, the count may be reset back to zero which indicates a service person performed scheduled maintenance on the printer.

If a user wants to view the current value of the maintenance page counter, the user may select “Maint Cnt Value.” When the current maintenance counter value is displayed, pressing Return causes the printer to return to the previous menu. All other operator panel keys are ignored. The following screen illustrates the current maintenance counter value.

Show 4 more labels / short text on this page
Perm Page Count · =1234567* · Maint Cnt Value · =1234567*
Page 131 of the Lexmark Printer user manual — Viewing the Error Log
Page 131 · click to enlarge
Page 131

4085-001

To reset the maintenance page counter, the user selects “Reset Maint Cnt.” Pressing Select causes the maintenance page counter to be reset back to zero. The following screen is displayed momentarily to indicate the counter is changing.

SAVED

When the reset operation is complete, the printer returns to the “PRINTER SETUP Reset Maint Cnt” screen.

Diagnostics (Mode 2) - Error Log

Viewing the Error Log

The Error Log aids the Customer Engineer by providing a history of printer errors. It contains the 12 most recent errors. The most recent error is displayed in position 1, and the oldest error is displayed in position 12 (assuming 12 or more errors have occurred). If fewer than 12 errors have occurred, then the oldest error is displayed in the position before the empty log entries begin. Empty log entries are identified with an error number of 000. Occupied log entries contain the error number for the message that is displayed on the operator panel. For example, 925 is contained in the log when a 925 Service Error occurs.

If an error occurs after the log is full, the oldest error in the log is discarded to make room for the new error. The printer stores identical errors in consecutive positions in the log. In other words, error log position N and position N+1 could contain the same error code if the same error occurs twice in a row.

The following error messages are stored in the error log.

  • All 2xx paper jam messages
  • All 9xx service messages

To view the error log, select the Display Log operation from the Diagnostics ERROR LOG menu. The entire error log cannot be displayed on a single screen. Four error log entries are displayed per screen. Therefore, the entire error log takes up 3 screens. To move

Reset Maint Cnt · Diagnostic Aids 3-37

Page 132 of the Lexmark Printer user manual — Clearing the Error Log
Page 132 · click to enlarge
Page 132

4085-001

forward in the log, press Menu>. To move backward in the log, press Menu<.

Here is an example of the error log screens:

To exit the error log, press Return or Stop.

Clearing the Error Log

To clear the error log, select the Clear Log operation from the ERROR LOG menu. The following message is displayed.

Select Yes to confirm that you really want to clear the log. The error log is cleared and the empty log is displayed:

Select No to exit the Clear Log menu. Pressing Return or Stop also exits the Clear Log menu.

Show 10 more labels / short text on this page
1-200 2-920 · 3-928 4-922 · 5-250 6-990 · 7-230 8-230 · 9-953 10-000 · 11-000 12-000 · Clear Log · =Yes · 1-000 2-000 · 3-000 4-000
Page 133 of the Lexmark Printer user manual — Menu List Display
Page 133 · click to enlarge
Page 133

4085-001

Exiting Diagnostics Mode

To exit diagnostics mode and POR the printer into normal user mode, press Exit Diagnostics.

Menus

This section describes the printer settings and operations that are accessible using the operator panel. In addition, it describes the format of the display and the operation of the buttons while the menus are active.

See “Using the Operator Panel” on page 1-4 for an illustration of the operator panel and a description of the buttons and indicator lights.

Understanding the Menu Display and Menu Buttons

The printer settings and operations that are accessible using the operator panel are organized into a list of menus. The contents of each menu relate to a common subject.

  • PAPER MENU - Printer settings that relate to paper handling.
  • SUPPLIES MENU - Printer settings that relate to the supplies.
  • COLOR MENU - Printer settings that relate to color, and so on.

List of menus in the Ready Menu Group:

SUPPLIES MENU, COLOR MENU, PAPER MENU, FINISHING MENU, UTILITIES MENU, SETUP MENU, PCL EMUL MENU, PARALLEL MENU, USB MENU.

Menu List Display

PAPER MENU

Initially the user is presented with the list of available menus. Only one menu can be displayed at a time, so the first menu in the list is displayed as shown. If the Menu> button is pressed to gain access into a menu group, then the menu displayed is the last menu in the first menu in the associated group.

Diagnostic Aids 3-39

Page 134 of the Lexmark Printer user manual — Printer Setting Display
Page 134 · click to enlarge
Page 134

4085-001

The buttons always act on the information displayed on the second line of the display.

The buttons act as follows while the PAPER MENU screen is displayed:

  • Menu> displays the next menu in the list.
  • Menu< displays the previous menu in the list.
  • Return returns to the previous menu level displayed on line 1. Since there is no previous level in this case (that is, line 1 is blank), pressing this button exits the menus and returns the printer to its previous state.
  • Select chooses the PAPER MENU. The display changes as shown.

Printer Setting Display

PAPER MENU

After a specific menu is selected (PAPER MENU in this example), the menu name is displayed on line 1 and the first printer setting in the menu is displayed on line 2. (In some menus, printer settings are grouped together into another menu. For these menus another menu could be displayed instead of a printer setting.)

The buttons always act on the information displayed on the second line of the display.

The buttons act as follows while the screen is displayed:

  • Menu> displays the next menu or printer setting in the menu.
  • Menu< displays the previous menu or printer setting in the menu.
  • Return returns to the previous menu level displayed on line 1. The display changes as shown in “Menu List Display” on page 3-39 .
  • Select chooses the menu or printer setting. For this example, the display changes as shown.

Paper Source

Page 135 of the Lexmark Printer user manual — 4085-001
Page 135 · click to enlarge
Page 135

4085-001

Printer Setting Value List Display

After a specific printer setting is selected (Paper Source in this example), the active printer setting is displayed on the first line and the default value (Tray 1) is displayed on the second line. An equal sign indicates it is assigned to the printer setting. An asterisk is displayed next to the currently selected or default value.

The buttons always act on the information displayed on the second line of the display.

The buttons act as follows while the screen is displayed:

  • Menu> displays the next value in the printer setting’s value list.
  • Menu< displays the previous value in the printer setting’s value list.
  • Return returns to the previous menu level displayed on line 1. For this example, the display changes as defined in “Printer Setting Display” on page 3-40 .
  • Select saves the new value currently displayed for the printer setting. The Saved message is displayed momentarily on the second line, and then the printer returns to the previous menu level as shown in “Printer Setting Display” on page 3-40 .

Paper Source · =Tray 1* · Diagnostic Aids 3-41

Page 136 of the Lexmark Printer user manual — COLOR MENU
Page 136 · click to enlarge
Page 136

4085-001

Example of Modifying a Printer Setting Using the Operator Panel

Use the following to modify any printer setting or initiate any operation in the Busy/Waiting Menu Group, Ready Menu Group, or Diagnostic Menu Group. The only variation is the action required to access the Diagnostics Menu Group (see “Entering CE Diagnostics Mode” on page 3-2 for details).

To change the PCL Orientation setting in the Ready Menu Group:

1. Press Menu> when the Ready message is displayed to access the Ready Menu Group. The printer is offline and the first menu (SUPPLIES MENU) is displayed on the second line.

SUPPLIES MENU

2. Press Menu> or Menu< repeatedly until the menu you want to access is displayed on the second line. Press Select to display the first setting or menu contained in that menu.

COLOR MENU is displayed on line 1, and the first entry in the menu is the Font Source printer setting and it is displayed on line 2.

COLOR MENU

3. Press Menu> or Menu< repeatedly until the printer setting that you want to change is displayed on the second line. Press Select to display the default value for that printer setting. (If the printer setting you want to modify is in another menu, then press Menu> or Menu< repeatedly until the menu which contains the printer setting you want to change is displayed on the second line, and press Select to enter the menu. Note: The Print Quality printer setting is displayed on line 1, and the default value (Normal) is displayed on line 2. An asterisk is always displayed next to the default or currently selected value. An equal

Print Quality

Page 137 of the Lexmark Printer user manual — COLOR
Page 137 · click to enlarge
Page 137

4085-001

sign precedes each value, indicating the entry on line 1 is a printer setting and it can be assigned to the value on line 2.

4. Press Menu> or Menu< repeatedly until the value that you want to select is displayed on the second line, then press Selec t. (Printer settings with a numeric value list let you scroll through the setting’s value list by pressing and holding Menu> or Menu

COLOR

5. Exit the menus and continue processing print jobs, then press Go . 6. To change a printer setting in another menu, repeatedly press Return until you reach the menu list level. Repeat the preceding steps to find and modify the next printer setting.

COLOR

Show 4 more labels / short text on this page
Print Quality · =Normal* · Print Quality · Diagnostic Aids 3-43
Page 138 of the Lexmark Printer user manual — Menu Groups
Page 138 · click to enlarge
Page 138

4085-001

Operator Panel Menu Definition

The operator panel settings and operations are divided into 4 menus groups, which are described in the following table.

Menu Groups

The Busy/Waiting menu group contains the operations that are accessible when the printer is receiving or processing data, waiting for additional data, or actually printing a job. One or more operations in this menu group may also be accessible with some error conditions or with certain status messages.

To access this menu group, press Menu> or Menu< while the printer is busy processing a job, waiting for additional data, or has posted a particular message which allows access to this menu group. See “Busy/ Waiting Menu Group” on page 3-45 for a description of the operations contained in the Busy/Waiting menu group.

The Ready menu group contains the settings and operations that are accessible when the printer is idle (that is, no jobs being received, processed, or printed).

To access this menu group, press the Menu> or Menu< button while the printer is idle. See “Ready Menu Group” on page 3-48 for a description of the settings and operations contained in the Ready menu group.

Busy/Waiting · Menu Group · Ready Menu Group

Page 139 of the Lexmark Printer user manual — JOB MENU
Page 139 · click to enlarge
Page 139

4085-001

The Configuration menu group contains a set of menus, settings, and operations which are infrequently required by a user. Generally, the options made available in this menu group are used to configure a printer for operation.

Use the Select and Return POR key sequence to access this menu. For additional information, see “Configuration Menu Group” on page 3-60.

The Diagnostic menu group contains the settings and operations used while manufacturing and servicing the printer.

See “Entering CE Diagnostics Mode” on page 3-2 for a description of how to enter the Diagnostics menus.

See “Diagnostics Menu Group (Mode 1: Printing)” on page 3-62 for a description of the settings and operations contained in the Diagnostic menu group.

Busy/Waiting Menu Group

The Busy/Waiting Menu group contains two menus: JOB MENU and SUPPLIES MENU. Press Menu> from the BUSY screen and the following screen is displayed.

JOB MENU

The following table shows the menus in the Busy/Waiting Menu group.

Top-Level Menu Intermediate Menus or Menu Items

JOB MENU See “Job Menu” on page 3-46 for a list of the menu items.

SUPPLIES MENU See “SUPPLIES MENU” on page 3-48. for a list of the menu items.

Configuration Menu Group · Diagnostic Menu Group · Diagnostic Aids 3-45

Page 140 of the Lexmark Printer user manual — 4085-001
Page 140 · click to enlarge
Page 140

4085-001

Job Menu

Job Menu Operations Operation Value or Description

No selection exists for this operation. Press Select to initiate the cancel print job function. For additional information, see“Canceling a Print Job using the Operator Panel” on page 3-12.

This operation is not available in the JOB MENU when the menu is accessed through the Ready Menu Group.

Cancel Job

Page 141 of the Lexmark Printer user manual — 4085-001
Page 141 · click to enlarge
Page 141

4085-001

Job Menu Operations Operation Value or Description

No selection exists for this operation. Press Select to initiate the reset function. For additional information, see “Resetting the Printer using the Operator Panel” on page 3-14.

This operation is always displayed in the JOB MENU when the menu is accessed through the Ready Menu Group. For additional information regarding the Ready Menu Group, see “Ready Menu Group” on page 3-48.

No selection exists for this operation. Press Select to initiate printing the contents of the printer’s buffer. For additional information, see “Printing Buffer Contents” on page 3-18.

This operation is not available in the JOB Menu when the menu is accessed through the Ready Menu Group.

Reset Printer · Print Buffer · Diagnostic Aids 3-47

Page 142 of the Lexmark Printer user manual — Ready Menu Group
Page 142 · click to enlarge
Page 142

4085-001

If no function is available in the JOB MENU at the time the JOB MENU is accessed, the printer prohibits entry into the JOB MENU, and the key press used to gain entry into the JOB MENU is ignored. To provide the user with some feedback, the Menus Disabled message is shown. For example, if Cancel Control is set to off, and Reset Control is set to off, and no optional bins are installed, and assuming the printer is not “Waiting”, then the JOB MENU is not available for selection except using the Ready Menu Group. Furthermore, if the printer is “Waiting” and Cancel Control is set to off, and Reset Control is set to off, and Print Buffer Control is set to off, and no optional output bins are installed, then the JOB MENU is not available for selection except via the Ready Menu Group.

SUPPLIES MENU

The SUPPLIES MENU in the Busy/Waiting Menu group is identical to the SUPPLIES MENU in the Ready Menu group.

Ready Menu Group

The Ready Menu group contains multiple menus. They are displayed on the operator panel in the order shown. The names of the top-level menus are capitalized and end with “MENU.” Whereas, the names of the intermediate menus (for example, SERIAL OPTION 1) are just capitalized.

Top-Level Menu Intermediate Menu, Setting, or Operation

SUPPLIES MENU See “SUPPLIES MENU” on page 3-49 for a list of the menus or settings.

COLOR MENU See “COLOR MENU” on page 3-50 for a list of the menus or settings.

PAPER MENU See “PAPER MENU” on page 3-51 for a list of the menus or settings.

FINISHING MENU See “FINISHING MENU” on page 3-51 for a list of the menus or settings.

UTILITIES MENU See “UTILITIES MENU” on page 3-52 for a list of the operations.

Page 143 of the Lexmark Printer user manual — SUPPLIES MENU
Page 143 · click to enlarge
Page 143

4085-001

Top-Level Menu Intermediate Menu, Setting, or Operation

JOB MENU See “JOB MENU” on page 3-54 for a list of the operations.

SETUP MENU See “SETUP MENU” on page 3-54 for a list of the menus or settings.

PCL EMUL MENU See “PCL EMUL MENU” on page 3-56 for a list of the menus or settings.

PARALLEL MENU See “PARALLEL MENU” on page 3-58 for a list of the menus or settings.

USB MENU See “USB MENU” on page 3-59 for a list of the menus or settings.

SUPPLIES MENU

The Supplies Menu updates as changes occur even if you are viewing it.The list is only status for the items which are near or past replacement.

Intermediate Menu or Setting Value

Show 10 more labels / short text on this page
Black Cartridge =Low · =Refilled · =Life Warning · Cyan Cartridge =Low · =Refilled · =Life Warning · Magenta Cartridge =Low · =Refilled · =Life Warning · Diagnostic Aids 3-49
Page 144 of the Lexmark Printer user manual — COLOR MENU
Page 144 · click to enlarge
Page 144

4085-001

Intermediate Menu or Setting Value

Black Printhead =Life Warning

Color Printhead =Life Warning

COLOR MENU

The following table lists the settings in the COLOR MENU and their corresponding value choices. The factory default setting for each item is indicated with an asterisk.

Intermediate Menu or Setting Value

Print Quality =Ink Saver

Show 8 more labels / short text on this page
Yellow Cartridge =Low · =Refilled · =Life Warning · PerfectFinish =Empty · Tray 1 =Empty · Tray 2 =Empty · =Normal* · =Best
Page 145 of the Lexmark Printer user manual — FINISHING MENU
Page 145 · click to enlarge
Page 145

4085-001

PAPER MENU

The following table lists the menus and settings in the PAPER MENU, and their corresponding values. The factory default value for each setting is indicated with an asterisk.

Intermediate Menu or Setting Value

Paper Source =Tray 1*

If the Paper Source, Separator Source, or Staple Prime Source is set to MP Feeder when Configure MP is changed to Manual or First, then the setting is changed to Tray 1.

FINISHING MENU

The following table lists the menus and settings in the FINISHING MENU, and their corresponding values. The factory default value for each setting is indicated with an asterisk.

Intermediate Menu or Setting Value

Blank Pages =Do Not Print*

Show 6 more labels / short text on this page
=Tray 2 · =MP Feeder · =Manual Paper · =Manual Env · =Print · Diagnostic Aids 3-51
Page 146 of the Lexmark Printer user manual — UTILITIES MENU
Page 146 · click to enlarge
Page 146

4085-001

Intermediate Menu or Setting Value

Separator Source Note: Only installed paper sources are displayed. MP Feeder is only displayed when Configure MP is set to Cassette.

UTILITIES MENU

The following table lists the operations in the TESTS MENU. For a detailed description of each operation, see “Printer Operations” on page 3-1.

Show 6 more labels / short text on this page
Separator Sheets =None* · =Between Jobs · =Between Pages · =Tray 1* · =Tray 2 · =MP Feeder
Page 147 of the Lexmark Printer user manual — =1...9 (5*) • F Alignment
Page 147 · click to enlarge
Page 147

4085-001

Print Menus No selections exist for this operation. Press Select to initiate this operation. See “Printing Menu Settings Page” on page 3-10.

Align Printheads No selections exist for this operation. Press Select to initiate this operation. See “Aligning the Printheads” on page 3-5. After the alignment page is printed, the user enters alignment values for each of the sections of the alignment page.

  • A Alignment
  • B Alignment
  • C Alignment

=1...15 (8*) • D Alignment

  • E Alignment

=1...9 (5*) • F Alignment

  • G Alignment

=1...15 (8*)

Clean Printheads See “Cleaning Printheads” on page 3-7.

See “Change Ink Cartridges” on page 3-4.

Change Printheads See “Change Printheads” on page 3-4.

Show 5 more labels / short text on this page
Operation Value · = Short Clean · = Long Clean · Change Ink Cartridges · Diagnostic Aids 3-53
Page 148 of the Lexmark Printer user manual — SETUP MENU
Page 148 · click to enlarge
Page 148

4085-001

Factory Defaults See “Restoring Factory Defaults” on page 3-12.

Hex Trace No selections exist for this operation. Press Select to initiate this operation. See “Activating Hex Trace Debug Mode” on page 3-19.

JOB MENU

The following table lists the operations in the JOB MENU.

Reset Printer Printer For information regarding this operation, see “Job Menu” on page 3-46.

SETUP MENU

The following table lists the menus and printer settings in the SETUP MENU, and their corresponding values. The factory default value for each setting is indicated by an asterisk.

Setting or Operation Value

=1...255 (90*)

=5...255

Show 6 more labels / short text on this page
Operation Value · =Restore · =Do Not Restore · Operation Value · Print timeout =Disabled · Auto Continue =Disabled*
Page 149 of the Lexmark Printer user manual — 4085-001
Page 149 · click to enlarge
Page 149

4085-001

Setting or Operation Value

Display Language Default set by country

Show 16 more labels / short text on this page
=English · =French · =German · =Italian · =Spanish · =Danish · =Norwegian · =Dutch · =Swedish · =Portuguese · =Finnish · =Japanese · Alarm Control =Off · =Single* · =Continuous · Diagnostic Aids 3-55
Page 150 of the Lexmark Printer user manual — PCL EMUL MENU
Page 150 · click to enlarge
Page 150

4085-001

Setting or Operation Value

Ink Low Alarm =Off

Dry Time Delay =Disabled*

=3...30

PCL EMUL MENU

The following table lists the menus and settings in the PCL EMUL MENU, and their corresponding values. The factory default value for each setting is indicated by an asterisk.

Intermediate Menu or Setting Value

Font Name =list of available font names for the default font source (R0 Courier*)

Symbol Set =list of symbol sets available for the default font (US=PC-8* / NonUS=PC-850*)

=Single* · =Continuous · =Auto

Page 151 of the Lexmark Printer user manual — Font Name Display Format
Page 151 · click to enlarge
Page 151

4085-001

Intermediate Menu or Setting Value

Lines per Page =1... 255 (US=60* / NonUS=64*)

Auto CR after LF =Off*

Auto LF after CR =Off*

Font Name Display Format

The font names are shown on both lines of the operator panel using the following format.

An equal sign precedes the font name, signifying the value list level of the menus.

S represents the font source abbreviation (R for resident, D for download, F for flash, and K for disk).

##### represents the font ID. The maximum length is five digits.

ThisIsTheFontName represents the font name from the font data. If the font name is too long to fit on the display, then it is truncated.

An asterisk is displayed after the factory default font name.

Show 7 more labels / short text on this page
Orientation =Portrait* · =Landscape · =On · =On · =S##### ThisIsThe- · FontName* · Diagnostic Aids 3-57
Page 152 of the Lexmark Printer user manual — PARALLEL MENU
Page 152 · click to enlarge
Page 152

4085-001

Symbol Set Display Format

The symbol sets are shown on both lines of the operator panel using the following format.

An equal sign precedes the symbol set ID, signifying the value list level of the menus.

SSID represents the symbol set ID (that is, 8U for Roman-8 symbol set).

PARALLEL MENU

The following table lists the menu and settings in the parallel port menus and their corresponding values. The factory default value for each setting is indicated by an asterisk.

NPA Mode a =On

Parallel Buffer a =Disabled

=3 K ... (max size allowed)

Show 12 more labels / short text on this page
=SSID ThisIsSym- · bolSetName · Setting Value · =Off · =Auto* · =Auto* · Advanced Status =Off · =On* · Protocol =Standard · =Fastbytes* · Honor Init =Off* · =On
Page 153 of the Lexmark Printer user manual — USB MENU
Page 153 · click to enlarge
Page 153

4085-001

a Whenever the value of NPA Mode, Parallel Buffer, or Job Buffering is changed from the operator panel, the printer automatically restarts upon exiting the menus to reconfigure memory.

USB MENU

The following table lists the menus and printer settings contained in the USB port menus and their corresponding values. The factory default value for each printer setting is indicated by an asterisk.

NPA Mode a =On

USB Buffer a =Disabled

=3K ... (max size allowed)

a Whenever the value of NPA Mode, USB Buffer, or Job Buffering is changed from the operator panel, the printer will automatically reboot upon exiting the menus in order to reconfigure memory.

Show 12 more labels / short text on this page
Setting Value · Parallel Mode 1 · =Off* · =On · Parallel Mode 2 · =Off · =On* · Operation Value · =Off · =Auto* · =Auto* · Diagnostic Aids 3-59
Page 154 of the Lexmark Printer user manual — 4085-001
Page 154 · click to enlarge
Page 154

4085-001

Configuration Menu Group

The Configuration Menu group contains a set of menus, settings and operations which are infrequently required by a user. Generally, the options made available in this menu group are used to configure a printer for operation. Each option is displayed on the operator panel in the order shown. The names of the top-level menus are capitalized. For a detailed description of each operation, follow the reference contained in the following table. Access to the Configuration Menu Group is gained by using a POR key sequence. For additional information regarding these sequences, see “Printer Operations” on page 3-1.

To indicate that the Configuration Menu Group is currently active, the CONFIG MENU is shown as a top level menu on the first line of the display.

Intermediate Menu, Setting or Operation Value

Only displayed when the PJL PASSWORD Environment variable is set to zero.

For additional information regarding modification of this printer setting, see “Disable/Enable Operator Panel Menus” on page 3-2.

Factory Defaults =Restore All

For additional information regarding this operation see “Clear NVRAM (non- critical sections only)” on page 3-3.

Panel Menus · =Disable · =Enable*

Page 155 of the Lexmark Printer user manual — - E
Page 155 · click to enlarge
Page 155

4085-001

Intermediate Menu, Setting or Operation Value

Coarse Alignment No selections exist for this operation. Press Select to initiate this operation. See “Aligning the Printheads” on page 3-5. After the alignment page is printed, the user enters alignment values for each of the sections of the alignment page.

- D

=1...15 (8*)

- E

=1...27 (13*)

Enable PHCE Mode =Disable*

Exit Config Menu No selections exist for this operation. Press Select to exit the CON-FIG MENU and restart the printer.

=Enable · Diagnostic Aids 3-61

Page 156 of the Lexmark Printer user manual — REGISTRATION
Page 156 · click to enlarge
Page 156

4085-001

Diagnostics Menu Group (Mode 1: Printing)

The Diagnostics Menu group contains multiple menus. They are displayed on the operator panel in the order shown. The names of the top-level menus are capitalized. For a detailed description of each Diagnostic test, follow the reference contained in the following table.

Top-Level Menu Intermediate Menu, Setting, or Operation Value

REGISTRATION

The following printer settings are in the REGISTRATION menu. However, they are not displayed as shown. See “Registration” on page 3-19 for a description of how the settings are displayed

  • Tray1
  • Tray 2 Note: Only displayed if Tray 2 is installed.
  • MP Feeder Note: Only displayed if the printer is configured with a Multi-Purpose Feeder

Left Margin =20...20 (0)

=20...20 (0

Top Margin

Page 157 of the Lexmark Printer user manual — Diagnostics Menu Group (Mode 2: Non-printing)
Page 157 · click to enlarge
Page 157

4085-001

Top-Level Menu Intermediate Menu, Setting, or Operation Value

PRINT TESTS

Only displayed if Tray 2 is installed.

Prt Contacts Pg See “Contacts Page Print Test” on page 3-22.

EXIT DIAGNOSTICS

See “Exiting Diagnostics Mode” on page 3-39.

Diagnostics Menu Group (Mode 2: Non-printing)

The Diagnostics Menu group contains multiple menus. They will be displayed on the operator panel in the order shown. The names of the top-level menus are capitalized. For a detailed description of each Diagnostic test, follow the reference in the following table.

Show 9 more labels / short text on this page
Tray 1 =Single · =Continuous · Tray 2 · =Single · =Continuous · MP Feeder · =Single · =Continuous · Diagnostic Aids 3-63
Page 158 of the Lexmark Printer user manual — BASE SENSOR TESTS
Page 158 · click to enlarge
Page 158

4085-001

Top-Level Menu Intermediate Menu, Setting, or Operation Value

INPUT TRAY TESTS

Tray 1 See “Tray 1 Sensor Test” on page 3-27.

Tray 2 See “Tray 2 Sensor Test” on page 3-27.

MP Feeder See “MP Feeder Sensor Test” on page 3-28.

HARDWARE TESTS

LCD Test See “LCD Hardware Test” on page 3-22.

Button Test See “Button Test” on page 3-23.

DRAM Memory Test See “DRAM Memory Test” on page 3-23.

ROM Memory Test See “ROM Memory Test” on page 3-24.

Parallel Wrap See “Parallel Wrap Test” on page 3-25.

BASE SENSOR TESTS

Paper Path Sensors See “Paper Path Sensors” on page 3-29.

Supplies Sensors See “Supplies Sensors” on page 3-29.

See “Miscellaneous Sensors” on page 3-30.

Ink Level Test See “Ink Level Sensor Test” on page 3-31.

Miscellaneous Sensors

Page 159 of the Lexmark Printer user manual — PRINTER SETUP
Page 159 · click to enlarge
Page 159

4085-001

Top-Level Menu Intermediate Menu, Setting, or Operation Value

SUBSYSTEM TESTS

Uncap Printheads See “Uncap Printheads” on page 3-31.

Cap Printheads See “Cap Printheads” on page 3-31.

Carrier System Test See “Carrier System Test” on page 3-32.

Index System Test See “Index System Test” on page 3-33.

Maintenance Sled Test See “Maintenance Sled Test” on page 3-33.

SUPPLIES TESTS

Ink Tank Memories See “Ink Tank Memories” on page 3-34.

Printhead Memories See “Printhead Memories” on page 3-34.

K&C TSR See “K&C TSR Test” on page 3-35.

M&Y TSR See “M&Y TSR Test” on page 3-35.

PRINTER SETUP

Defaults =U.S.*

=Non-U.S.

Page Count =0 to 9999999 (0)

Perm Page Count =0 to 9999999 (0)

Serial Number =xxxxxxxx (printer serial number) where x = A-Z or 0-9

Par S Strobe Adj =-4 to 6 (0)

Diagnostic Aids 3-65

Page 160 of the Lexmark Printer user manual — EXIT DIAGNOSTICS
Page 160 · click to enlarge
Page 160

4085-001

Top-Level Menu Intermediate Menu, Setting, or Operation Value

ERROR LOG

Display Log See “Viewing the Error Log” on page 3-37.

Clear Log See “Clearing the Error Log” on page 3-38.

EXIT DIAGNOSTICS

See “Exiting Diagnostics Mode” on page 3-39.

=Yes · =No

Page 161 of the Lexmark Printer user manual — Handling ESD-Sensitive Parts
Page 161 · click to enlarge
Page 161

4085-001

4. Repair Information

This chapter explains how to make adjustments to the printer and how to remove defective parts.

Handling ESD-Sensitive Parts

Many electronic products use parts that are known to be sensitive to electrostatic discharge (ESD). To prevent damage to ESD-sensitive parts, follow the instructions below in addition to all the usual precautions, such as turning off power before removing logic boards:

  • Keep the ESD-sensitive part in its original shipping container (a special “ESD bag”) until you are ready to install the part into the printer.
  • Make the least-possible movements with your body to prevent an increase of static electricity from clothing fibers, carpets, and furniture.
  • Put the ESD wrist strap on your wrist. Connect the wrist band to the engine ground point. This discharges any static electricity in your body to the printer.
  • Hold the ESD-sensitive part by its edge connector shroud (cover); do not touch its pins. If you are removing a pluggable module, use the correct tool.
  • Do not place the ESD-sensitive part on the printer cover or on a metal table; if you need to put down the ESD-sensitive part for any reason, first put it into its special bag.
  • Printer covers and metal tables are electrical grounds. They increase the risk of damage because they make a discharge path from your body through the ESD-sensitive part. (Large metal objects can be discharge paths without being grounded.)
  • Prevent ESD-sensitive parts from being accidentally touched by other personnel. Install printer covers when you are not working on the printer, and do not put unprotected ESD-sensitive parts on a table.
  • If possible, keep all ESD-sensitive parts in a grounded metal cabinet (case).
  • Be careful in working with ESD-sensitive parts when cold weather heating is used because low humidity increases static electricity.

Repair Information 4-1

Page 162 of the Lexmark Printer user manual — Releasing Plastic Latches
Page 162 · click to enlarge
Page 162

4085-001

Adjustments

The user is directed, in the Printer Control program, to perform the printhead to printhead and bidirectional alignment adjustments after replacing a print cartridge.

Removal Procedures

The following procedures are arranged according to the name of the printer part discussed.

Releasing Plastic Latches

Many of the parts are held in place with plastic latches. The latches break easily; release them carefully. To remove such parts, press the hook end of the latch away from the part to which it is latched.

Page 163 of the Lexmark Printer user manual — 4085-001
Page 163 · click to enlarge
Page 163

4085-001

Rear Cover Removal

1. Open the rear door. 2. Remove Multi-Purpose Feeder. 3. Remove two clips and remove the top door. 4. Remove the four screws {A}. 5. Depress the four latches {B}. 6. Remove the rear cover.
Lexmark Printer — 4085-001 diagram (page 163)
Fig. 4

Repair Information 4-3

Page 164 of the Lexmark Printer user manual — 4085-001
Page 164 · click to enlarge
Page 164

4085-001

Lexmark Printer — 4085-001 diagram (page 164)
Fig. 5
Page 165 of the Lexmark Printer user manual — Exit Tray Removal
Page 165 · click to enlarge
Page 165

4085-001

Operator Panel Cover/Operator Panel Removal

1. Remove the rear cover. 2. Remove the screw {A}. 3. Lift the cover and unplug the operator panel from the engine board. 4. Remove the four screws located on the rear operator panel housing. 5. Remove the operator panel.
Lexmark Printer — 4085-001 diagram (page 165)
Fig. 6

Exit Tray Removal

1. Remove the paper tray. 2. Depress the latch on the bottom of the tray. 3. Lift the front of the exit tray and pull forward to remove. Note: Use care not to damage the bat wings.

Repair Information 4-5

Page 166 of the Lexmark Printer user manual — 4085-001
Page 166 · click to enlarge
Page 166

4085-001

Left Frame Cover Removal

1. Open the top door. 2. The restraint screw does not have to be removed. The restraint has a T-end which can be twisted and removed. Partially close the top cover, twist the end of the strap that is in the machine and remove. 3. Remove the two screw {A} from the left frame cover. 4. Remove the cover.
Lexmark Printer — 4085-001 diagram (page 166)
Fig. 7
Page 167 of the Lexmark Printer user manual — 4085-001
Page 167 · click to enlarge
Page 167

4085-001

Left Cover Removal

1. Remove the rear cover. 2. Remove the exit tray cover. 3. Move carrier to the right. 4. Remove the screw {A} from the left side of the carrier frame. 5. Remove the two screws {B} from the left front side of the paper tray frame. 6. Remove the cover. Note: When reinstalling, reinsert cover guides before installing the screws. Cover guides are located on the bottom edge of the cover.
Lexmark Printer — 4085-001 diagram (page 167)
Fig. 8

Repair Information 4-7

Page 168 of the Lexmark Printer user manual — 4085-001
Page 168 · click to enlarge
Page 168

4085-001

Lexmark Printer — 4085-001 diagram (page 168)
Fig. 9
Page 169 of the Lexmark Printer user manual — 4085-001
Page 169 · click to enlarge
Page 169

4085-001

Right Cover/Power Switch Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3. 2. Remove the exit tray. Refer to “Exit Tray Removal” on page 4-5. 3. Remove the operator panel cover. Refer to “Operator Panel Cover/Operator Panel Removal” on page 4-5. 4. Move the carrier to the left. 5. Disconnect the power switch from the power supply. Note the wire routing. 6. Remove two screws {A} from the right carrier frame. 7. Remove the two screws {B} from the lower right front side of the paper tray frame. 8. Remove the cover. Note: When reinstalling, reinsert the cover guides before installing the screws. Cover guides are located on the bottom edge of the cover.

Lexmark Printer — 4085-001 diagram (page 169)
Fig. 10

Repair Information 4-9

Page 170 of the Lexmark Printer user manual — 4085-001
Page 170 · click to enlarge
Page 170

4085-001

Lexmark Printer — 4085-001 diagram (page 170)
Fig. 11
Page 171 of the Lexmark Printer user manual — 4085-001
Page 171 · click to enlarge
Page 171

4085-001

Left Tray Cover Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3 . 2. Remove the exit tray cover. Refer to “Exit Tray Removal” on page 4-5 . 3. Remove the left cover. Refer to “Left Cover Removal” on page 4-7 . 4. Remove the three screws {A} that secure the left tray cover. 5. Remove the left tray cover.

Repair Information 4-11

Page 172 of the Lexmark Printer user manual — 4085-001
Page 172 · click to enlarge
Page 172

4085-001

Right Tray Cover Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3 . 2. Remove the exit tray cover. Refer to “Exit Tray Removal” on page 4-5 . 3. Remove the right cover. Refer to “Right Cover/Power Switch Removal” on page 4-9 . 4. Remove the three screws {A} that secure the right tray cover. 5. Remove the right tray cover.
Page 173 of the Lexmark Printer user manual — 4085-001
Page 173 · click to enlarge
Page 173

4085-001

Ink Levels and Temperature Sensor with Bracket Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3 . 2. Remove the operator panel cover. Refer to “Operator Panel Cover/Operator Panel Removal” on page 4-5 . 3. Disconnect the ink level and temperature sensor connector (J12) on the engine board. Note the wire routing. 4. Remove the right cover. 5. Remove the screw {A} from the sensor bracket. 6. Remove the sensor and bracket {B}.
Lexmark Printer — 4085-001 diagram (page 173)
Fig. 12

Repair Information 4-13

Page 174 of the Lexmark Printer user manual — 4085-001
Page 174 · click to enlarge
Page 174

4085-001

Engine Board /Cover Removal

1. Remove the rear cover. 2. Remove left frame cover. Refer to “Left Frame Cover Removal” on page 4-6 . 3. Remove the two screws {A} from the engine board cover and the cover. 4. Disconnect all connectors and cables from the engine board. 5. Remove the four screws and remove the engine board. Note the routing of the ground cable.
Lexmark Printer — 4085-001 diagram (page 174)
Fig. 13
Page 175 of the Lexmark Printer user manual — 4085-001
Page 175 · click to enlarge
Page 175

4085-001

Carrier with Card Removal

1. Remove all covers. 2. Remove all ink cartridges from carrier. 3. Remove engine board cover. Refer to “Tray 2 Covers Removal” on page 4-49. 4. Loosen the set screw {A} on the belt tensioner. 5. Remove the tension from the belt and retighten the set screw. 6. Remove the belt keepers from the ends of the belt {B}. The open end of the keepers should face the rear of the carrier. 7. Remove the belt. 8. Disconnect the spring {C} and remove two screws {D} from the support shaft bracket located on the right side. 9. Slide the carrier guide rod out the right side. 10. Remove the encoder strip. Note the routing of the encoder strip through a sensor at the rear of the carrier. Be careful not to touch the encoder strip in any areas that the sensor uses. Handle the encoder strip no further in than 4 cm from each side. 11. Disconnect the carrier clip and cables from the engine board. 12. Remove the carrier. Note: When reinstalling, insure correct orientation of the support shaft bracket and linkage.

Lexmark Printer — 4085-001 diagram (page 175)
Fig. 14

Repair Information 4-15

Page 176 of the Lexmark Printer user manual — 4085-001
Page 176 · click to enlarge
Page 176

4085-001

Lexmark Printer — 4085-001 diagram (page 176)
Fig. 15
Lexmark Printer — 4085-001 diagram (page 176)
Fig. 16
Page 177 of the Lexmark Printer user manual — Multi-Purpose Feeder (MPF) Motor and Sensor Removal
Page 177 · click to enlarge
Page 177

4085-001

Carrier 1st Stage Drive Belt Removal

1. Remove the motor bracket from the printer frame. 2. Loosen the three screws securing the motor plate to the motor assembly. 3. Gently depress the motor so that the 1st stage drive belt is loosened. Retighten the three screws to fix this position. 4. Remove the original belt and install the new belt. 5. Loosen the three screws to allow the motor bracket to apply proper belt tension. Retighten in a clockwise order, as installed in the machine, starting with the screw closest to the tensioner rivet. Next tighten the screw closest to the tensioner spring. 6. Ensure that the belt is aligned by rotating the compound pulley two or three times.

Carrier Printhead Latch Removal

1. Turn the printer off. 2. Open the front cover. 3. Move the carrier to the center. 4. Remove print cartridges from the carrier. 5. Remove the clips and washer from both sides. 6. Disconnect the pogo housing link on the right side. 7. Remove the carrier printhead latch.

Multi-Purpose Feeder (MPF) Motor and Sensor Removal

1. Remove multi-purpose feeder from the printer. 2. Remove the left and right end covers. 3. Remove one screw {A} from the right side of the rear cover. 4. Remove the rear cover. 5. Depress the clips and remove the sensor. 6. Depress the clips on the electrical connector and remove the connector from gear bracket. 7. Remove the three screws {B} from the gear bracket. 8. Remove the gear bracket. 9. Remove the two screws. 10. Remove the motor.

Repair Information 4-17

Page 178 of the Lexmark Printer user manual — 4085-001
Page 178 · click to enlarge
Page 178

4085-001

Lexmark Printer — 4085-001 diagram (page 178)
Fig. 17
Lexmark Printer — 4085-001 diagram (page 178)
Fig. 18
Page 179 of the Lexmark Printer user manual — 4085-001
Page 179 · click to enlarge
Page 179

4085-001

Power Supply Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3 . 2. Disconnect all power supply cables, and ground straps. Note routing of the cables and straps. 3. Remove the three mounting screws {A} that attach the power supply to the frame. 4. Remove the power supply.
Lexmark Printer — 4085-001 diagram (page 179)
Fig. 19

Repair Information 4-19

Page 180 of the Lexmark Printer user manual — 4085-001
Page 180 · click to enlarge
Page 180

4085-001

Pump Housing/Maintenance Station/Ink Waste Tank/ Transport Carrier Motor Removal

1. Remove all covers. 2. Remove the power supply. Refer to “Power Supply Removal” on page 4-19. 3. Slide the ink waste tank out the rear of the printer. Note the routing of the hose into tank. 4. Remove the carrier belt. Refer to “Engine Board /Cover Removal” on page 4-14. 5. Disconnect transport carrier motor cable from engine board. 6. Remove three screws {A} from the transport carrier motor bracket. 7. Remove the motor and bracket. 8. Loosen the screw on the maintenance bracket and depress the spring, then retighten the screw. 9. Remove the spring from the rear of the maintenance station. 10.Remove the screw {B} from the right side of the frame that secures the pump housing maintenance station assembly. 11.Push in the guide post {C} and move the pump housing maintenance station assembly forward and down to disconnect it from the shaft. 12. Slide the assembly out the rear of the printer and remove.

Lexmark Printer — 4085-001 diagram (page 180)
Fig. 20
Page 181 of the Lexmark Printer user manual — 4085-001
Page 181 · click to enlarge
Page 181

4085-001

Lexmark Printer — 4085-001 diagram (page 181)
Fig. 21

Repair Information 4-21

Page 183 of the Lexmark Printer user manual — 4085-001
Page 183 · click to enlarge
Page 183

4085-001

Cover-Open Sensor Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3 . 2. Remove the exit tray cover. Refer to “Exit Tray Removal” on page 4-5 . 3. Remove the left cover. Refer to “Left Cover Removal” on page 4-7 . 4. Remove the engine card cover. 5. Unplug the cover-open sensor (J18) connector. 6. Depress two latches and remove the cover-open sensor.

Repair Information 4-23

Page 184 of the Lexmark Printer user manual — 4085-001
Page 184 · click to enlarge
Page 184

4085-001

RIP-EMC Shield Assembly/RIP Card Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3. 2. Remove the power supply. Refer to “Power Supply Removal” on page 4-19. 3. Disconnect (J14) RIP cable from the engine board. 4. Remove the six screws {A} from the RIP card. 5. Remove the RIP card. Note routing of cable. 6. Remove the six screws {B} from the shield assembly. 7. Remove the shield assembly. Note: Anytime the RIP card is replaced, a course alignment has to be done. Refer to “Coarse Alignment” on page 3-5.

Lexmark Printer — 4085-001 diagram (page 184)
Fig. 22
Page 185 of the Lexmark Printer user manual — 4085-001
Page 185 · click to enlarge
Page 185

4085-001

Lexmark Printer — 4085-001 diagram (page 185)
Fig. 23

Repair Information 4-25

Page 186 of the Lexmark Printer user manual — 4085-001
Page 186 · click to enlarge
Page 186

4085-001

PerfectFinish Sensor Assembly/Rear Paper Path Sensor Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3. 2. Remove the power supply. Refer to “Power Supply Removal” on page 4-19. 3. Remove the RIP-EMC shield assembly and RIP card. Refer to “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24. 4. Disconnect the wire from the PerfectFinish sensor. 5. Remove two screws from the PerfectFinish sensor. 6. Remove the PerfectFinish sensor. 7. Remove the PerfectFinish tank. 8. Remove two screws and remove the PerfectFinish cartridge. 9. Unsnap the rear paper path sensor arm and remove. Note the position of the spring. 10. Lift the left side, unlatch the paper path sensor. 11. Disconnect the wire from paper path sensor. 12. Remove the paper path sensor.

Page 187 of the Lexmark Printer user manual — 4085-001
Page 187 · click to enlarge
Page 187

4085-001

Frame From Base Removal

1. Remove all covers. Refer to “Rear Cover Removal” on page 4-3. 2. Remove the power supply. Refer to “Power Supply Removal” on page 4-19. 3. Remove the maintenance tank through the rear of the printer. 4. Disconnect (J2) the transport carrier motor from the engine board. 5. Disconnect (J17) the paper port II from the engine board. 6. Disconnect the star wheel follower spring {A} from the base assembly. 7. Remove the four screws {B} from the left side frame plate. 8. Remove the two screws {C} on the right side frame plate. 9. Before placing the printer on its back, remove the PerfectFinish applicator to prevent spilling. 10. Place the printer on its back and remove five screws {D} from the base. 11. Lift and slide the frame forward and remove.

Lexmark Printer — 4085-001 diagram (page 187)
Fig. 24

Repair Information 4-27

Page 188 of the Lexmark Printer user manual — 4085-001
Page 188 · click to enlarge
Page 188

4085-001

Lexmark Printer — 4085-001 diagram (page 188)
Fig. 25
Page 189 of the Lexmark Printer user manual — Cam Engine Motor with Gear Removal
Page 189 · click to enlarge
Page 189

4085-001

Lexmark Printer — 4085-001 diagram (page 189)
Fig. 26

Cam Engine Motor with Gear Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3 . 2. Remove the exit tray cover. Refer to “Exit Tray Removal” on page 4-5 . 3. Remove the left cover. Refer to “Left Cover Removal” on page 4-7 . 4. Disconnect the cam engine motor connector (J8) from the engine board. 5. Remove the two screws {A} from the motor. 6. Remove the motor through the front of the printer. Note the routing of the wires.

Repair Information 4-29

Page 190 of the Lexmark Printer user manual — 4085-001
Page 190 · click to enlarge
Page 190

4085-001

Page 191 of the Lexmark Printer user manual — 4085-001
Page 191 · click to enlarge
Page 191

4085-001

Paper Feed Pick Arm Assembly with Motor and Paper Path Sensor Removal

1. Remove all covers. 2. Remove power supply. Refer to “Power Supply Removal” on page 4-19. 3. Remove the frame from the base. Refer to “Frame From Base Removal” on page 4-27. 4. Remove the two lower screws on the base of the RIP shield. 5. Disconnect the integrated tray connector (J6) from the engine board and disconnect the paper path sensor. 6. Remove the E-clip {A} from the pick assembly shaft. 7. Remove the screw {B} from the paper feed frame assembly. 8. Slide the shaft to the left and remove the pick arm assembly. 9. Disconnect the wire from the paper path sensor and snap the sensor out to remove. When reinstalling, note the routing of the wires and position of spring.

Lexmark Printer — 4085-001 diagram (page 191)
Fig. 27

Repair Information 4-31

Page 192 of the Lexmark Printer user manual — 4085-001
Page 192 · click to enlarge
Page 192

4085-001

PerfectFinish Gear Plate Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3 . 2. Remove E-clips {A} from bellcrank diverter link and remove link. 3. Remove helical drive gear {B} and cartridge drive gear under it. Note the position of the cartridge drive gear under the helical drive gear. 4. Remove three screws and remove plate.
Lexmark Printer — 4085-001 diagram (page 192)
Fig. 28
Page 194 of the Lexmark Printer user manual — 4085-001
Page 194 · click to enlarge
Page 194

4085-001

Encoder Disk Feed Roller Assembly Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3. 2. Remove the operator panel cover. Refer to “Operator Panel Cover/Operator Panel Removal” on page 4-5. 3. Remove the exit tray cover. Refer to “Exit Tray Removal” on page 4-5. 4. Remove the left cover. Refer to “Left Cover Removal” on page 4-7. 5. Remove the thrust bracket CBM {A}. 6. Remove the index board assembly. 7. Remove the five backup roller springs {B}. Note orientation of springs before removing. 8. Remove the encoder disk feed roller assembly through the left side of the printer. Note: The index card and the encoder disk feed roller must be replaced as a matching set. See “Index Card Assembly Removal” on page 4-22. Also replace the thrust bracket and the cleaning roller.

Page 195 of the Lexmark Printer user manual — 4085-001
Page 195 · click to enlarge
Page 195

4085-001

Lexmark Printer — 4085-001 diagram (page 195)
Fig. 29

Repair Information 4-35

Page 196 of the Lexmark Printer user manual — 4085-001
Page 196 · click to enlarge
Page 196

4085-001

Star Wheel Shaft Assembly Removal

1. Remove all covers. 2. Remove the carrier and belt. Refer to “Engine Board /Cover Removal” on page 4-14. 3. Remove pump housing maintenance station, tank, and transport carrier motor. Refer to “Pump Housing/Maintenance Station/Ink Waste Tank/Transport Carrier Motor Removal” on page 4-20. 4. Disconnect the spring {A} connecting the base assembly to the star wheel cam follow assembly. 5. Remove the E-clip {B} from the right end of the star wheel shaft. 6. Slide the shaft to the left and lift out. Disconnect the star wheel cam follow from the cam shaft assembly. 7. Remove the star wheel assembly.

Page 197 of the Lexmark Printer user manual — 4085-001
Page 197 · click to enlarge
Page 197

4085-001

Lexmark Printer — 4085-001 diagram (page 197)
Fig. 30

Repair Information 4-37

Page 198 of the Lexmark Printer user manual — 4085-001
Page 198 · click to enlarge
Page 198

4085-001

Paper Feed Platen Assembly Removal

1. Remove all covers. 2. Remove the carrier and belt. Refer to “Engine Board /Cover Removal” on page 4-14. 3. Remove the pump housing maintenance station, tank, and the transport carrier motor. Refer to “Pump Housing/Maintenance Station/Ink Waste Tank/Transport Carrier Motor Removal” on page 4-20. 4. Remove the star wheel shaft. 5. Press down gently on both sides and remove the paper feed platen out through the front of the printer. Be careful not to damage the platen bias studs. 6. Remove the paper feed platen.

Page 199 of the Lexmark Printer user manual — 4085-001
Page 199 · click to enlarge
Page 199

4085-001

Exit Shaft with Gear Removal

1. Remove all covers. 2. Remove carrier and belt. Refer to “Engine Board /Cover Removal” on page 4-14. 3. Remove pump housing, maintenance station, tank, and transport carrier motor. Refer to “Pump Housing/Maintenance Station/Ink Waste Tank/Transport Carrier Motor Removal” on page 4-20. 4. Remove star wheel shaft. Refer to “Star Wheel Shaft Assembly Removal” on page 4-36. 5. Remove paper feed platen. Refer to “Paper Feed Platen Assembly Removal” on page 4-38. 6. Remove the E-clip from the right end of the exit shaft. 7. Move exit shaft to the left, lift and pull to the right to remove the exit shaft gear {A}. Note the orientation of the gear before removal. 8. Remove the exit shaft.

Lexmark Printer — 4085-001 diagram (page 199)
Fig. 31

Repair Information 4-39

Page 200 of the Lexmark Printer user manual — 4085-001
Page 200 · click to enlarge
Page 200

4085-001

Paper Feed Frame and Motor/Cam Shaft Assembly Removal

1. Remove all covers. 2. Remove the carrier and belt. Refer to “Engine Board /Cover Removal” on page 4-14. 3. Remove pump housing, maintenance station, tank and transport carrier motor. Refer to “Pump Housing/Maintenance Station/Ink Waste Tank/Transport Carrier Motor Removal” on page 4-20. 4. Remove the star wheel shaft. See “Star Wheel Shaft Assembly Removal” on page 4-36. 5. Remove paper feed platen. Refer to “Paper Feed Platen Assembly Removal” on page 4-38. 6. Remove encoder disk and feed roller assembly. Refer to “Encoder Disk Feed Roller Assembly Removal” on page 4-34. 7. Remove frame from base. Refer to “Frame From Base Removal” on page 4-27. 8. Disconnect all cable connectors from the engine board. 9. Remove the two E-clips {A} on the backup roller assembly shaft. 10. Remove the two upper frame support screws {B}. 11. Move the paper feed frame with motor to the right and remove. 12. Pull the cam shaft assembly to the right and remove the gear. 13. Remove the cam shaft assembly. Before removing the paper feed frame and motor, note the position of the bat wings on the cam shaft.

Page 201 of the Lexmark Printer user manual — 4085-001
Page 201 · click to enlarge
Page 201

4085-001

Lexmark Printer — 4085-001 diagram (page 201)
Fig. 32

Repair Information 4-41

Page 202 of the Lexmark Printer user manual — 4085-001
Page 202 · click to enlarge
Page 202

4085-001

Lexmark Printer — 4085-001 diagram (page 202)
Fig. 33
Page 203 of the Lexmark Printer user manual — 4085-001
Page 203 · click to enlarge
Page 203

4085-001

Left Index Frame Pivot Assembly Removal

1. Remove all covers. 2. Remove the carrier and belt. Refer to “Engine Board /Cover Removal” on page 4-14. 3. Remove the pump housing, maintenance station, tank, and transport carrier motor. Refer to “Pump Housing/Maintenance Station/Ink Waste Tank/Transport Carrier Motor Removal” on page 4-20. 4. Remove the star wheel shaft. Refer to “Star Wheel Shaft Assembly Removal” on page 4-36. 5. Remove paper feed platen. Refer to “Paper Feed Platen Assembly Removal” on page 4-38. 6. Remove encoder disk feed roller assembly. See “Encoder Disk Feed Roller Assembly Removal” on page 4-34. 7. Remove the frame from the base. Refer to “Frame From Base Removal” on page 4-27. 8. Disconnect all cable connectors from the engine board. 9. Remove paper feed frame and motor. Refer to “Paper Feed Frame and Motor/Cam Shaft Assembly Removal” on page 4-40. 10. Remove the index motor. Refer to “Index Motor Assembly Removal” on page 4-33. 11. Remove the two index frame springs {A}. 12. Remove the three screws {B} from the left index frame pivot assembly. 13. Remove the left index frame pivot assembly.

Repair Information 4-43

Page 204 of the Lexmark Printer user manual — 4085-001
Page 204 · click to enlarge
Page 204

4085-001

Page 205 of the Lexmark Printer user manual — 4085-001
Page 205 · click to enlarge
Page 205

4085-001

Right Index Frame Pivot Assembly Removal

1. Remove all covers. 2. Remove the carrier and belt. Refer to “Engine Board /Cover Removal” on page 4-14. 3. Remove the pump housing, maintenance station, tank and the transport carrier motor. Refer to “Pump Housing/Maintenance Station/Ink Waste Tank/Transport Carrier Motor Removal” on page 4-20. 4. Remove the star wheel shaft. Refer to “Star Wheel Shaft Assembly Removal” on page 4-36. 5. Remove the paper feed platen. Refer to “Paper Feed Platen Assembly Removal” on page 4-38. 6. Remove encoder disk feed roller assembly. Refer to “Encoder Disk Feed Roller Assembly Removal” on page 4-34. 7. Remove the two index frame springs {A}. 8. Remove three screws and washers {B} from the right index frame pivot assembly. 9. Remove the right index frame pivot assembly.

Lexmark Printer — 4085-001 diagram (page 205)
Fig. 34

Repair Information 4-45

Page 206 of the Lexmark Printer user manual — 4085-001
Page 206 · click to enlarge
Page 206

4085-001

Bat Wings and Bushings Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3 . 2. Remove the spring between the cam followers. 3. Remove the two E-clips from the ends of the bat wing shaft. 4. Remove bushings. 5. Pull forward and remove.
Page 207 of the Lexmark Printer user manual — 4085-001
Page 207 · click to enlarge
Page 207

4085-001

Backup Roller Assembly Removal

1. Remove all covers. 2. Remove carrier and belt. Refer to “Engine Board /Cover Removal” on page 4-14. 3. Remove pump housing, maintenance station, tank and transport carrier motor. Refer to “Pump Housing/Maintenance Station/Ink Waste Tank/Transport Carrier Motor Removal” on page 4-20. 4. Remove star wheel shaft. Refer to “Star Wheel Shaft Assembly Removal” on page 4-36. 5. Remove the paper feed platen. Refer to “Paper Feed Platen Assembly Removal” on page 4-38. 6. Remove the backup roller springs. 7. Remove the index board assembly. Refer to “Index Card Assembly Removal” on page 4-22. 8. Remove the encoder disk feed roller assembly. Refer to “Encoder Disk Feed Roller Assembly Removal” on page 4-34. 9. Remove the frame from the base. Refer to “Frame From Base Removal” on page 4-27. 10. Disconnect all cable connectors from the engine board. 11. Remove, from the left side frame, two E-clips on the right side of the backup roller assembly. 12. Move the paper feed frame and motor to the right and remove. Refer to “Paper Feed Frame and Motor/Cam Shaft Assembly Removal” on page 4-40. 13. Move the backup roller assembly shaft to the left and remove it from the right bushing. 14. Move the backup roller assembly to the right and out of the inner deflector and remove. Note: When removing the backup roller assembly, use care not to damage the paper sensor flag.

Repair Information 4-47

Page 208 of the Lexmark Printer user manual — Carrier/Cable Retainer Removal
Page 208 · click to enlarge
Page 208

4085-001

Backup Roller Spring Removal

1. Lift the front door on the printer. 2. Press the coil on the backup roller spring to center and remove. Note the position of the spring before removing.

Carrier/Cable Retainer Removal

1. Remove all covers. 2. Remove the engine board cover. 3. Disconnect carrier cables from the engine board. 4. Remove the carrier guide shaft from the carrier. 5. Unlatch the cable restraint, disconnect carrier cables from the rear of the carrier and remove. 6. Depress the retainer cable clip, move the cable to the right and remove.
Page 209 of the Lexmark Printer user manual — Tray 2 Covers Removal
Page 209 · click to enlarge
Page 209

4085-001

Peristaltic Pump Removal

1. Remove the rear cover. Refer to “Rear Cover Removal” on page 4-3 . 2. Remove the exit tray. Refer to “Exit Tray Removal” on page 4-5 . 3. Remove the operator panel cover. Refer to “Operator Panel Cover/Operator Panel Removal” on page 4-5 . 4. Remove right cover. Refer to “Right Cover/Power Switch Removal” on page 4-9 . 5. Remove the power supply and tank. Note: When reinstalling the pump, be sure the gear alignment is correct.
6. Remove the two screws from the peristaltic pump and disconnect the pump from the gear.

Tray 2 Covers Removal

1. Remove ten screws {A} from Tray 2 covers. 2. Remove the covers.
Lexmark Printer — Tray 2 Covers Removal diagram (page 209)
Fig. 35 · Tray 2 Covers Removal

Repair Information 4-49

Page 210 of the Lexmark Printer user manual — 4085-001
Page 210 · click to enlarge
Page 210

4085-001

Tray 2 Paper Pick Arm Assembly Removal

1. Remove all covers 2. Remove eight screws {A} from Tray 2 base. 3. Remove E-clip {B} from pick assembly shaft. 4. Remove the screw {C} from the paper feed frame assembly. 5. Slide the shaft to the left and remove the pick arm assembly.
Lexmark Printer — 4085-001 diagram (page 210)
Fig. 36
Page 211 of the Lexmark Printer user manual — 4085-001
Page 211 · click to enlarge
Page 211

4085-001

Lexmark Printer — 4085-001 diagram (page 211)
Fig. 37

Repair Information 4-51

Page 212 of the Lexmark Printer user manual — 4085-001
Page 212 · click to enlarge
Page 212

4085-001

Tray 2 Paper Feed Motor and Card Assembly Removal

1. Remove the left cover from Tray 2. 2. Remove the four screws from the paper port connector frame. 3. Remove the paper port connector frame. 4. Remove the two paper feed motor screws {A}. 5. Disconnect the paper feed motor connector. 6. Remove the motor.
Lexmark Printer — 4085-001 diagram (page 212)
Fig. 38
Page 213 of the Lexmark Printer user manual — J14 RIP
Page 213 · click to enlarge
Page 213

4085-001

5. Connector Locations

Engine Board

J3 Maintenance Station Motor and Homing

J5 Thin-Coat Motor and Encoder

J12 Ink-Level and Temperature Sensing

J14 RIP

J17 Paper Port II Tray2

Show 15 more labels / short text on this page
J1 Power Supply · J2 Carrier Motor · J4 Operator Panel · J6 Integrated Tray · J8 Cam System · J9 Thin-Coat Sensing · J10 MPF-Feeder · J11 Paper-Path Sensing · J15 Index System · J16 Index Motor · J18 Cover-Open Sensor · J21 Carrier Connector · J22 Carrier Connector · J23 Carrier Connector · Connector Locations 5-1
Page 214 of the Lexmark Printer user manual — 4085-001
Page 214 · click to enlarge
Page 214

4085-001

RIP Card

Page 215 of the Lexmark Printer user manual — 4085-001
Page 215 · click to enlarge
Page 215

4085-001

RIP Card (cont.)

J4 USB

Show 4 more labels / short text on this page
J1 Power Supply · J2 Engine · J3 Parallel · Connector Locations 5-3
Page 216 of the Lexmark Printer user manual — 4085-001
Page 216 · click to enlarge
Page 216

4085-001

Optional Tray 2

J1 Paper Feed Motor

J3 Paper Feed Pic Motor

J4 Paperport II and Power

J2 Passthru Sensor

Page 217 of the Lexmark Printer user manual — Carrier Transport System Pulleys
Page 217 · click to enlarge
Page 217

4085-001

6. Preventive Maintenance

This chapter contains lubrication specifications. Follow these recommendations to prevent problems and maintain optimum performance.

Lubrication Specifications

Lubricate only when parts are replaced or as needed, not on a scheduled basis. Use of lubricants other than those specified can cause premature failure. Some unauthorized lubricants may chemically attack polycarbonate parts. Use IBM no. 10 oil, PN 1280443 (Approved equivalents: Mobil DTE27, Shell Tellus 100, Fuchs Renolin MR30), IBM no. 23 grease (Approved equivalent Shell Darina 1), and grease, PN 99A0394 Nyogel 744 to lubricate appropriate areas of the machine.

Numbers in {} refer to items in Assembly 4: Carrier Transport.

Carrier Shafts

  • Apply Nye Nyogel 744 uniformly across the top portion of the 8mm {1} and 12mm carrier shafts. The grease should be visible to the eye on the shafts, but not dripping from the shafts. Use 0.03 to 0.06 grams for the 8mm shaft {1}. For reference, use 0.08 to 0.16 grams for the 12 mm shaft.
  • Remove any excessive coatings or accumulations with a lintfree cloth. When applying Nyogel 744 to the top of the 8mm shaft, ensure that no grease contacts the encoder strip as a carrier system stall could result during the Power-OnSequence or during printing. Note: Do not let the Nyogel 744 come in contact with the pogo pin housing. May cause machine failure.

Carrier Transport System Pulleys

  • Apply Shell Tellus #100 to the pulley bores of the top idler pulleys {3} and tensioner {13}. The amount of oil to b used should be visible in the pulley bore, but should not drip. For reference, use approximately 0.003 grams per pulley.

Preventive Maintenance 6-1

Page 218 of the Lexmark Printer user manual — Carrier Card Pogo Pins
Page 218 · click to enlarge
Page 218

4085-001

  • Avoid oil contact with the outer pulley surface and flanges that contact the belt.

Motor Pulley Studs

  • Apply Shell Tellus #100 oil to the idler stud and compound pulley stud {8}. The amount of Shell Tellus #100 to be used should be visible on the stud but not dripping or running onto the motor bracket, pulleys or frame. For reference, use approximately 0.005 grams on the compound pulley stud and approximately 0.003 grams on the idler pulley stud.

Carrier Latch Camshaft Lubrication

  • With the carrier handle raised to disengage the camshaft, apply small drops of Nye Uniflor 8512 (0.01 grams to 0.02 grams per cam) to the carrier backup bracket in the regions directly behind the camshaft lobes.
  • Open and close the handle a couple of times to ensure that the contacting surfaces of the cams and bracket have been lubricated.
  • If appropriate, remove any excess lubricant from the bracket around these regions, being careful to avoid contamination of the carrier card or carrier cables. Lubricant should not drip down the carrier card bracket.

Carrier Card Pogo Pins

  • Use Nye Tact 570H-10 to lubricate the ink tank pogo pins on the carrier card assembly. Use of an appropriate fixture is needed to properly lubricate the ink tank pogo pins. For reference, this amount should be about 0.05 grams wet.
  • Shake well before applying Nyetact 570H-10 lubricant. Depress the applicator bottle on each set of pogo pins only once, avoiding excessive drippage on other parts of the carrier card.
Page 219 of the Lexmark Printer user manual — 4085-001
Page 219 · click to enlarge
Page 219

4085-001

7. Parts Catalog

How To Use The Parts Catalog

  • NS: (Not Shown) in the Asm-Index column indicates that the part is procurable but is not shown in the illustration.
  • PP: in the Description column indicates the part is available in the listed parts packet.

Parts Catalog 7-1

Page 220 of the Lexmark Printer user manual — 4085-001
Page 220 · click to enlarge
Page 220

4085-001

Assembly 1: Covers

Page 221 of the Lexmark Printer user manual — 4085-001
Page 221 · click to enlarge
Page 221

4085-001

Assembly 1: Covers

Part Number Units Description

1-1 12G6073 1 Cover Assembly, Manual Feed

2 12G6070 1 Door, Rear

3 12G6069 1 Cover, Rear

4 12G6065 1 Cover, Operator Panel

5 12G6061 1 Cover, Right

6 12G6063 1 Cover, Right Tray

7 12G6072 1 Cover Assembly, Exit Tray

8 12G6075 1 Paper Tray Assembly

9 12G6062 1 Cover, Left Tray

10 12G6060 1 Cover, Left

11 12G6071 1 Top Door Assembly

12 12G6064 1 Cover, Left Frame

NS 12G6076 Screws, (PP)

Asm- Index · Parts Catalog 7-3

Page 222 of the Lexmark Printer user manual — 4085-001
Page 222 · click to enlarge
Page 222

4085-001

Assembly 2: Paper Feed

Page 223 of the Lexmark Printer user manual — 4085-001
Page 223 · click to enlarge
Page 223

4085-001

Assembly 2: Paper Feed

Part Number Units Description

2-1 12G6024 1 Paper Out Sensor

2 12G6000 1 Paper Feed Pick Assembly with Motor

3 12G6092 2 Pick Tires

Asm- Index · Parts Catalog 7-5

Page 224 of the Lexmark Printer user manual — 4085-001
Page 224 · click to enlarge
Page 224

4085-001

Assembly 2 (cont.): Paper Feed

Page 225 of the Lexmark Printer user manual — 4085-001
Page 225 · click to enlarge
Page 225

4085-001

Assembly 2 (cont.): Paper Feed

Part Number Units Description

2-2 12G6003 1 Left Bat Wing with Bushings

3 12G6004 1 Right Bat Wing with Bushings

4 12G6005 1 Bat Wing Follower Assembly

Asm- Index · Parts Catalog 7-7

Page 226 of the Lexmark Printer user manual — 4085-001
Page 226 · click to enlarge
Page 226

4085-001

Assembly 2 (cont.): Paper Feed

Lexmark Printer — 4085-001 diagram (page 226)
Fig. 39
Page 227 of the Lexmark Printer user manual — 4085-001
Page 227 · click to enlarge
Page 227

4085-001

Assembly 2 (cont.): Paper Feed

Part Number Units Description

2-5 12G6010 1 Deflector Assembly, Second Path

6 12G6031 1 Paper Exit Backup Roll Assembly

7 12G6008 1 Motor Assembly, PerfectFinish

8 12G6028 1 Platen with Spring and Levers Assembly

9 12G6027 1 Shaft, Exit Assembly with Gears

10 12G6029 1 Star Wheel Shaft Assembly

11 12G6006 1 Plate, Right Pivot

12 12G6026 1 Cam Shaft Assembly with Spring

13 12G6013 1 Motor, Camshaft

14 12G6074 1 Static Brush Bracket Assembly

15 12G6025 1 Motor, Index Assembly

16 12G6032 1 Starwheel Follower with Spring Assembly

17 12G6014 1 Plate, Left Pivot

18 12G6007 1 Left Plate Assembly, Automatic Sheet Feed

19 12G6009 1 PerfectFinish Drive Plate Assembly

NS 12G6094 1 Roller, Cleaning

NS 12G6095 1 Applicator, Cartridge Assembly

NS 12G6250 1 Sensor Assembly with Cable - Fluid Level

NS 12G6076 Screws, (PP)

NS 12G6097 1 Retainer/Bearing/Bushing (PP)

NS 12G6098 1 Spring (PP)

NS 12G6099 1 Washer/Clip/Keeper/Tubing (PP)

Asm- Index · Parts Catalog 7-9

Page 228 of the Lexmark Printer user manual — 4085-001
Page 228 · click to enlarge
Page 228

4085-001

Assembly 3: Electronics

Page 229 of the Lexmark Printer user manual — 4085-001
Page 229 · click to enlarge
Page 229

4085-001

Assembly 3: Electronics

Part Number Units Description

3-1 12G6059 1 RIP Card

2 12G6058 1 Shield, RIP Enclosure

3 12G6067 1 Cable, Operator Panel

4 12G6066 1 Operator Panel Assembly

5 12G6057 1 Power Supply

6 12G6048 1 Engine Board

7 12G6055 1 Sensor, Ink Level

8 12G6044 1 Index Card/Feedroll Encoder Disc Assembly

9 12G6018 1 Top Door Switch with Retainer

10 12G6053 1 Cable, Engine to RIP

11 12G6093 1 Bracket, Thrust

12 1339535 1 Power Cord, Canada, United States, Bolivia, Caribbean, Columbia, Costa Rica, Dominican Republic, Ecuador, El Salvador, Guatemala, Honduras, Mexico, Nicaragua, Panama, Peru, Puerto Rico, Venezuela, Virgin Islands, Papua, New Guinea, Phillippines, South Korea, Taiwan, Thailand

12 1339542 1 Power Cord, Italy

12 1342530 1 Power Cord, Brazil, Paraguay, Uruguay

12 1342534 1 Power Cord, Chile

12 1339537 1 Power Cord, Abu Dhabi, Ajman, Bahrain, Dubai, Fujeirah, Iraq, Kuwait, Lybia, Oman, Pakistan, Qatar, Ras-Al- Khaimah, Sharjah, U.A.E., UK/Ireland/ Iceland, Umm-Al-Qwain, Yemen, Hong Kong, Malasia, Singapore

12 1339536 1 Power Cord, Australia, New Zealand

12 1339539 1 Power Cord, Israel

12 1339540 1 Power Cord, Switzerland (Fr), Switzerland (German) Switzerland (It)

12 1339541 1 Power Cord, Botswana, Lesotho, Namibia, South Africa, Bangladesh, Sri Lanka

Asm- Index · Parts Catalog 7-11

Page 230 of the Lexmark Printer user manual — 4085-001
Page 230 · click to enlarge
Page 230

4085-001

Assembly 3 (cont.): Electronics

Page 231 of the Lexmark Printer user manual — 4085-001
Page 231 · click to enlarge
Page 231

4085-001

Assembly 3 (cont.): Electronics

Part Number Units Description

12 1339545 1 Power Cord, Argentina

12 1339538 1 Power Cord, Albania, Algeria, Armenia, Austria, Azerbijan, Belarus, Belgium, Benin, Bosnia, Bulgaria, Burkina-Faso, Cameroon, Central African Republic, Chad, Chechenya, Comoros, Congo, Croatia, Czek Republic, Djbouti, Egypt, Equatorial Guinea, Estonia, Euro English, Finland, France, French Guyana, Gabon, Gambia, Georgia, Germany, Greece, Guadeloupe, Guinea, Hungary, Iran, Ivory Coast, Jordan, Kazakhstan, Kirghizistan, Kyrgyz Republic, La Reunion, Latvia, Lebanon, Lettonia, Lithuania, Macedonia, Madagascar, Mali, Martinique, Mauritania, Mauritius, Mayottes, Moldavia, Moldova, Morocco, Netherlands, New Caledonia, Niger, Norway, Poland, Portugal, Romania, Russia, Saint Pierre et Miqueion, Senegal, Seychelles, Slovakia, Slovenia, Spain/Catalan, Sweden, Syria, Tahiti, Tajikistan, Togo, Tunisia, Turkey, Turkmenistan, Ukraine, Uzbekistan, Vanuatu, Wallis & Futuna, Yugoslavia (Serbia & Montenegro)

12 1342514 1 Power Cord, Saudia Arabia, Indonesia, Japan

12 43H9547 1 Power Cord, Peoples Republic China

NS 12G6012 1 Cables, Camshaft Motor and TDC Sensor

NS 12G6017 1 PerfectFinish Sensor (Flag)

NS 12G6045 1 Power Switch with Cable

NS 12G6046 1 Input Sensor

NS 12G6047 1 PerfectFinish Sensor Cable

NS 12G6050 1 Cable, Auto Connect - Tray 2

NS 12G6051 1 Cable, Rear Feeder

NS 12G6052 1 Cable, Index Sensor

NS 12G6054 1 Cable, Fluid Level Sensor

NS 12G6068 1 Cover, Engine Board Assembly

NS 12G6076 1 Screws, (PP)

Asm- Index · Parts Catalog 7-13

Page 232 of the Lexmark Printer user manual — 4085-001
Page 232 · click to enlarge
Page 232

4085-001

Assembly 3 (cont.): Electronics

Page 233 of the Lexmark Printer user manual — 4085-001
Page 233 · click to enlarge
Page 233

4085-001

Assembly 3 (cont.): Electronics

Part Number Units Description

NS 12G6097 1 Retainer/Bearing/Bushing (PP)

NS 12G6098 1 Spring (PP)

NS 12G6099 1 Washer/Clip/Keeper/Tubing (PP)

Asm- Index · Parts Catalog 7-15

Page 234 of the Lexmark Printer user manual — 4085-001
Page 234 · click to enlarge
Page 234

4085-001

Assembly 4: Carrier Transport

Page 235 of the Lexmark Printer user manual — 4085-001
Page 235 · click to enlarge
Page 235

4085-001

Assembly 4: Carrier Transport

Part Number Units Description

4-1 12G6033 1 Shaft, Upper Carrier with Brackets

2 12G6037 1 Belt, Carrier Drive with Keepers

3 12G6038 2 Pulley Assembly with Shaft-Top Idler

4 12G6040 1 Clip, Encoder Strip

5 12G6039 1 Encoder, Carrier Drive

6 12G6035 1 Carrier Cables with Retainer and Clamps

7 12G6016 1 Belt, Carrier Drive

8 12G6015 1 Motor, Carrier Drive Assembly with Belt

9 12G6034 1 Carrier Assembly with Cables and Clamps

10 12G6036 1 Printhead Latch, Carrier

11 12G6042 1 Gears, Compound/Carrier Lift

12 12G6041 1 Carrier Lift Assembly

13 12G6030 1 Tensioner, Carrier Drive Belt

14 12G6200 1 Link, Pogo Housing

NS 12G6076 Screws, (PP)

NS 99A0394 1 Grease Packet, Nyogel 744

NS 99A0462 1 Grease Packet, IBM 23

NS 12G6097 1 Retainer/Bearing (PP)

Asm- Index · Parts Catalog 7-17

Page 236 of the Lexmark Printer user manual — 4085-001
Page 236 · click to enlarge
Page 236

4085-001

Assembly 5: Maintenance Station

Page 237 of the Lexmark Printer user manual — 4085-001
Page 237 · click to enlarge
Page 237

4085-001

Assembly 5: Maintenance Station

Part Number Units Description

5-1 12G6056 1 Waste Ink Bottle with Belt Shield

2 12G6022 1 Maintenance Regulator Assembly

3 12G6019 1 Maintenance Motor Assembly with Gear

4 12G6021 1 Peristaltic Pump Assembly

5 12G6020 1 Maintenance Station Assembly

6 12G6091 2 Wipers, Maintenance

7 12G6024 1 Maintenance Homing Sensor

8 12G6099 1 Washer/Clip/Keeper/Tubing (PP)

NS 12G6023 1 Maintenance Cable

NS 12G6076 Screws, (PP)

Asm- Index · Parts Catalog 7-19

Page 238 of the Lexmark Printer user manual — 4085-001
Page 238 · click to enlarge
Page 238

4085-001

Assembly 6: Optional Tray 2

Page 239 of the Lexmark Printer user manual — 4085-001
Page 239 · click to enlarge
Page 239

4085-001

Assembly 6: Optional Tray 2

Part Number Units Description

6-1 12G6088 1 Cover, Rear (OP Tray 2)

2 12G6002 4 Wear Strips

3 12G6049 1 Paper Feed Pick Assembly with Motor - 250 Option Final Assembly

4 12G6046 1 Sensor, Tray 2 Passthru

5 12G6086 1 Cover, Right Side (OP Tray 2)

6 12G6085 1 Cover, Front (OP Tray 2)

7 12G6089 1 Card, Secondary Tray

8 12G6001 1 Detent - Paper Tray 2 with Spring

9 12G6083 1 Motor, Redrive with Gear Assembly

10 12G6087 1 Cover, Left Side (OP Tray 2)

NS 12G6078 1 Cable, Tray 2 Power and Paper Port

NS 12G6080 1 Cable, Tray 2 Stepper Motor

NS 12G6076 1 Screw (PP)

NS 12G6098 1 Spring (PP)

Asm- Index · Parts Catalog 7-21

Page 240 of the Lexmark Printer user manual — 4085-001
Page 240 · click to enlarge
Page 240

4085-001

Assembly 7: Optional Multi-Purpose Feeder

Page 241 of the Lexmark Printer user manual — 4085-001
Page 241 · click to enlarge
Page 241

4085-001

Assembly 7: Optional Multi-Purpose Feeder

Part Number Units Description

7-1 12G6077 1 Guide, MPF Rear Paper

2 12G6011 1 Feeder, Auxillary Sheet

3 12G6084 1 MFP Motor with wire

Asm- Index · Parts Catalog 7-23

Page 242 of the Lexmark Printer user manual — 4085-001
Page 242 · click to enlarge
Page 242

4085-001

Assembly 8: Optional MarkNet External Print Server

Page 243 of the Lexmark Printer user manual — 4085-001
Page 243 · click to enlarge
Page 243

4085-001

Assembly 8: Optional MarkNet External Print Server

Part Number Units Description

8-1 12G6090 1 MarkNet™ External Print Server

NS 12G6251 1 MarkNet XP Cable

Asm- Index · Parts Catalog 7-25

Page 244 of the Lexmark Printer user manual — 4085-001
Page 244 · click to enlarge
Page 244

4085-001

Page 246 of the Lexmark Printer user manual — S
Page 246 · click to enlarge
Page 246

4085-00X

Power Consumption 1-1 Print Quality Test Page 3-8 Printer Indicator Light 1-4 Printer Messages 1-6 Printer Operations

Left Index Frame Pivot 4-43 Left Tray Cover 4-11 Maintenance Station 4-20 Multi-Purpose Feeder Motor 4-17 Multi-Purpose Feeder Sensor

CE Diagnostics Mode 3-2 Clear NVRAM 3-3 Disable/Enable OP Menus 3-2 Flash Engine Code Mode 3-3 Power-On Reset Button Functions

4-17 Operator Panel 4-5 Paper Feed Frame 4-40 Paper Feed Motor 4-40 Paper Feed Pick Assembly 4-31 Paper Feed Platen 4-38 PerfectFinish Gear Plate 4-32 PerfectFinish Motor 4-33 PerfectFinish Sensor 4-26 Peristaltic Pump 4-49 Power Supply 4-19 Pump Housing 4-20 Rear Cover 4-3 Rear Paper Path Sensor 4-26 Right Cover 4-9 Right Index Frame Pivot 4-45 Right Tray Cover 4-12 RIP Card 4-24 Star Wheel Shaft 4-36 Temperature Sensor 4-13 Transport Carrier Motor 4-20 Tray 2 Card Assembly 4-52 Tray 2 Covers 4-49 Tray 2 Paper Feed Motor 4-52 Tray 2 Paper Pick Arm Assembly

3-1 Printer Settings 1-9 Printing Menu Settings Page 3-10 Problems

Carrier Transport 2-50 Communications 2-50 Maintenance Station 2-50 Operator Panel 2-51 Paper Feed 2-51 Power 2-51 Print Quality 2-52

R

Ready Menu Group 3-48 Removals

Backup Roller Assembly 4-47 Backup Roller Spring 4-48 Bat Wings 4-46 Cam Engine Motor 4-29 Cam Shaft 4-40 Carrier Cable and Retainer 4-48 Carrier Printhead Latch 4-17 Carrier with Card 4-15 Cover-Open Sensor 4-23 Encoder Disk Feed Roller

4-50 Repair Information 4-1 Resetting the Printer 3-14 Restoring Factory Defaults 3-12

S

Assembly 4-34 Engine Board 4-14 Exit Shaft with Gear 4-39 Exit Tray Cover 4-5 Frame From Base 4-27 Index Board 4-22 Index Motor 4-33 Ink Level Sensor 4-13 Ink WasteTank 4-20 Left Cover 4-7

Safety Information viii Service Checks 2-53

Cam System Motor 2-69 Index Motor 2-56 Maintenance Functions 2-53 Maintenance Station 2-53 Multi-Purpose Feeder Motor 2-57 Multi-Purpose Feeder Sensor

X-2 Service Manual

Page 247 of the Lexmark Printer user manual — U
Page 247 · click to enlarge
Page 247

4085-001

Operator Panel (Buttons) 2-58 Operator Panel (LCD) Display

W

2-59 Options 2-59 Paper Feed 2-60 Power Supply 2-63 Print Quality 2-65 RIP Card 2-64 Transport 2-67 Service Messages 2-2 Start 2-1 Status Messages 2-14 Symptom Tables 2-50

Part Numbers

12G6000 7-5 12G6002 7-21 12G6003 7-7 12G6004 7-7 12G6005 7-7 12G6006 7-9 12G6007 7-9 12G6008 7-9 12G6009 7-9 12G6010 7-9 12G6011 7-23 12G6012 7-13 12G6013 7-9 12G6014 7-9 12G6015 7-17 12G6016 7-17 12G6017 7-13 12G6018 7-11 12G6019 7-19 12G6020 7-19 12G6021 7-19 12G6022 7-19 12G6023 7-19 12G6024 7-5, 7-19 12G6025 7-9 12G6026 7-9 12G6027 7-9 12G6028 7-9 12G6029 7-9 12G6030 7-17 12G6031 7-9 12G6032 7-9 12G6033 7-17 12G6034 7-17 12G6035 7-17 12G6036 7-17 12G6037 7-17 12G6038 7-17 12G6039 7-17 12G6040 7-17 12G6041 7-17 12G6042 7-17

T

Cap Printheads 3-31 Carrier System 3-32 DRAM Memory 3-23 Index System 3-33 Ink Level Sensor 3-31 Ink Tank Memories 3-34 K&C Thermal Sense Resistor

3-35 LCD Hardware 3-22 M&Y Thermal Sense Resistor

3-35 Maintenance Sled 3-33 Miscellaneous Sensors 3-30 MP Feeder Sensor 3-28 Paper Path Sensors 3-29 Parallel Wrap 3-25 Printhead Memories 3-34 ROM Memory 3-24 Supplies Sensors 3-29 Tray 1 Sensor 3-27 Tray 2 Sensor 3-27 Uncap Printheads 3-31 Tools 1-3

U

Unsolicited Manual Feed 3-10 User Error Messages 2-69 User Status Messages 2-10

Tests

Page 248 of the Lexmark Printer user manual — 4085-00X
Page 248 · click to enlarge
Page 248

4085-00X

12G6044 7-11 12G6045 7-13 12G6046 7-13 12G6047 7-13 12G6048 7-11 12G6049 7-21 12G6051 7-13 12G6052 7-13 12G6053 7-11 12G6054 7-13 12G6055 7-11 12G6056 7-19 12G6057 7-11 12G6058 7-11 12G6059 7-11 12G6060 7-3 12G6061 7-3 12G6062 7-3 12G6063 7-3 12G6064 7-3 12G6065 7-3 12G6066 7-11 12G6067 7-11 12G6068 7-13 12G6069 7-3 12G6070 7-3 12G6071 7-3 12G6072 7-3 12G6073 7-3 12G6074 7-9 12G6075 7-3 12G6076 7-3, 7-9, 7-13, 7-17, 7-19, 7-21 12G6077 7-23 12G6078 7-21 12G6080 7-21 12G6081 7-21 12G6083 7-21 12G6084 7-23 12G6085 7-21 12G6086 7-21 12G6087 7-21 12G6088 7-21 12G6089 7-21 12G6090 7-25 12G6091 7-19 12G6093 7-11

12G6094 7-9 12G6095 7-9 12G6097 7-9, 7-17 12G6098 7-9, 7-21 12G6099 7-9, 7-19 12G6200 7-17 12G6250 7-9 12G6251 7-25 1339535 7-11 1339536 7-11 1339537 7-11 1339538 7-13 1339539 7-11 1339540 7-11 1339541 7-11 1339542 7-11 1339545 7-13 1342514 7-13 1342530 7-11 1342534 7-11 43H9547 7-13 99A0394 7-17 99A0462 7-17

X-4 Service Manual

Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Display codes

Error codes

What the fault codes shown on the display mean and how to clear them.

CodeMeaningFix
900Perform the “RIP Card Service Check” on page 2-64 . p.25
902Replace the engine board. See the “Engine Board / Cover Removal” on page 4-14 . p.25
903Check RIP/Engine cable. Replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 . p.25
904Check cables. Replace the board in the optional tray. p.25
905Replace the engine board. See the “Engine Board / Cover Removal” on page 4-14 . p.25
906Replace the engine board. See the “Engine Board / Cover Removal” on page 4-14 . p.25
907Check cabling to index board. 10 - Replace engine board. See “Engine Board /Cover Removal” on page 4-14 . 20 - Replace index board. See “Index Card Assembly Removal” on page 4-22 . 30 - Replace engine board. 40 and 50 - Replace index board. p.26
908Check cabling to index board. Replace index board. See “Index Card Assembly Removal” on page 4-22 . p.26
910Perform the “Carrier System Test” on page 3-32 . This would be caused by printhead contacts or carrier card. Note: “Carrier Systems Test” would not find this. p.26
915Perform the “Index System Test” on page 3-33 . See “Index Motor Service Check” on page 2-56 . If problem still exists, go to “Index System Test” on page 3-33 . p.27
920See “Index Card/Sensor Service Check” on page 2-67 . p.27
921Check Motor and Encoder. See “Index Motor Service Check” on page 2-56 . If problem still exists, go to “Index System Test” on page 3-33 . p.27
922Check Multi-Purpose Feeder Motor. See “Multi- Purpose Feeder (MPF) Motor and Sensor Service Check” on page 2-57 . p.27
923See “Entering CE Diagnostics Mode” on page 3-2 . p.27
925See “Entering CE Diagnostics Mode” on page 3-2 and “Maintenance Sled Test” on page 3-33 . p.27
928Perform “Ink Level Sensor Test” on page 3-31 . p.27
930Check all contacts and cables. If tests fail, replace the printheads. If failure still occurs, replace engine board. p.28
931Check the printhead and tank contacts.Check the carrier to engine cables. Check the printhead and tank memory chip placement. If the problem remains, replace the engine board. See the “Engine Board / Cover Removal” on page 4-14 . p.28
932Replace printheads. See “Change Printheads” on page 3-4 . If contents of printhead memory are still invalid, replace engine board. See “Engine Board /Cover Removal” on page 4-14 . Check carrier cables. p.28
933Check the printhead/ carrier contacts. Try replacing the printheads before replacing the carrier. Check the carrier cable. If cable is OK, replace carrier. See “Carrier/Cable Retainer Removal” on page 4-48 . Try replacing both printheads. If problem remains, replace engine board. See “Engine Board /Cover Removal” on page 4-14 . p.28
934Check the carrier/ printhead contacts. Try replacing both printheads before replacing carrier. Check the carrier cable. If cable is OK, replace carrier. See “Carrier/Cable Retainer Removal” on page 4-48 . If problem remains, replace engine board. See “Engine Board /Cover Removal” on page 4-14 . p.29
935Try replacing the printheads before replacing carrier. Check the carrier cable. If cable is OK, replace carrier. See “Carrier/Cable Retainer Removal” on page 4-48 . If problem remains, replace engine board. See “Engine Board /Cover Removal” on page 4-14 . p.29
936Try replacing the printheads before replacing carrier. Check the carrier cable. If cable is OK, replace carrier. See “Carrier/Cable Retainer Removal” on page 4-48 . If problem remains, replace engine board. See “Engine Board /Cover Removal” on page 4-14 . p.29
938Check the printhead contacts. Overheated. Replace printhead. See “Change Printheads” on page 3-4 . If problem remains, replace carrier assembly. p.29
939Unplug and replug the AC power cord to see if the problem goes away. Check the RIP card cable connections. If the connections are good, replace the engine board. See “Engine Board /Cover Removal” on page 4-14 . If the problem remains, replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 . Note: The RIP software can cause a 939 error. p.30
953Replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 . p.30
954Replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 . p.30
955Replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 . p.30
956Replace the RIP card. See “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 . p.30
957Replace the RIP card. See “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 . p.30
960Replace the RIP card. See the “RIP-EMC Shield Assembly/RIP Card Removal” on page 4-24 . p.31
980Check connection between engine board and optional card. p.31
985Check engine to tray 2 cable and contacts. Replace tray 2 card. Look for PerfectFinish leaks. p.31
Fix-it

Troubleshooting

Common problems, likely causes, and what to do.

ProblemPossible causeRemedy
Blank display, carrier moves, paperfeed motor turnsSee the “Operator Panel (LCD) Display Service Check” on page 2-59 . p.71
All diamonds on displaySee the “Operator Panel (LCD) Display Service Check” on page 2-59 . p.71
Performing Self Test remains on display, no motors turnSee the “Power Supply Service Check” on page 2-63 . p.71
Index motor does not turnSee the “Index Motor Service Check” on page 2-56 . p.71
Maintenance motor does not turnSee the “Maintenance Station Service Checks” on page 2-55 . p.71
Carrier drives into side frameSee the “Carrier System Test” on page 3-32 . If carrier system test fails, replace the carrier assembly. p.71
Printer indicator light does not come on or fails to stay onSee the “Operator Panel (LCD) Display Service Check” on page 2-59 . p.71
POST is incomplete, printer indicator light is on, no motors turn and performing self-test is displayedSee the “Power Supply Service Check” on page 2-63 . p.71
Printer inoperableSee the “Power Supply Service Check” on page 2-63 . p.71
• No carrier movement • Slow carrier movement • Carrier stops • Carrier does not move to cartridge load position when opening access door • Carrier strikes left side frame. See page 2-48.See the “Transport Service Check” on page 2-67 . See the “Carrier System Test” on page 3-32 . p.72
Printer not communicating with host computerSee the “Parallel Wrap Test” on page 3-25 . p.72
Not able to print test pageCheck the USB cable and engine board cable connection. If okay, replace RIP card. p.72
• Fails to cap the printhead • Fails to clean the printhead • Pump fails to work • Maintenance assembly does not move • Maintenance assembly moves to forward position, then will not return • Access door switch does not work • Peristalic pump or motor does not work.See the “Maintenance Station Service Checks” on page 2-55 . See the “Maintenance Sled Test” on page 3-33 . p.72
Printer indicator light does not: • Turn on • Flash • Turn off • All diamondsSee the “Operator Panel (LCD) Display Service Check” on page 2-59 . p.73
One or two pels missingReplace the operator panel assembly. p.73
Only one button inoperativeReplace the operator panel assembly. p.73
More than one button inoperativeSee the “Operator Panel (Buttons) Service Check” on page 2-58 . p.73
Paper fails to stop at first print line • Fails to pick paper • Picks more than one sheet of paper • Picks paper but fails to feed • Paper jams • Paper fails to exit • Noisy paper feed • Paper skewsSee the “Paper Feed Service Check” on page 2-60 . p.73
• Paper does not feed, motor does not turn • Paper does not feed - motor attempts to turnSee “Paper feed pick assembly does not feed, paper feed pick motor does not turn” on page 2-61 . p.73
• Voids in characters • Light print • Prints off the page • Fuzzy print • Carrier moves but does not print • Printhead drying prematurely • Vertical alignment off • Excessive ink flow (flooding) • Horizontal bandingSee the “Print Quality Service Check” on page 2-65 . p.74
• Ink smearing • Vertical streaks on paper • Print lines crowdedSee the “Paper Feed Service Check” on page 2-60 . p.74

Ask about the Lexmark Printer

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the Lexmark Printer

Be the first to ask — other owners or our team will answer.

Original document

Lexmark Printer manual PDF

248 pages·3.6 MB·Printer·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…